ec-aht-o1 user manual

User Manual

EC-AHT-O1

Handheld Terminal

EC-AHT-O1 User Manual V1.0 2

Copyright Copyright2021 EC Electronics Limited. All rights reserved. No part of this document may be reproduced, distributed, translated, or stored in any form without the prior written permission of EC Electronics Limited. All brands and product names mentioned herein may be trademarks or registered trademarks of their respective owners. Product specifications are subject to change without prior notice.

Disclaimer The contents of this document are provided as is. EC Electronics Limited makes no representations or warranties with respect to the contents herein and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose. EC Electronics Limited reserves the right to revise this document at any time without prior notice.


Regulatory Information

FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement This device should be installed and operated with a minimum separation distance of 20cm between the radiator and all persons. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. CE Statement The SAR limit of Europe is 2.0 W/kg. The highest SAR value reported under this standard during product certification for body worn operation is 0.952 W/kg. To maintain compliance with RF exposure requirements, use accessories that maintain a 1.5cm separation distance between the user's body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided. Hereby, EC Electronics Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.


Safety Information

Please read the following information carefully before using the device for the first time, and keep this User Manual in a safe place for future reference. Always treat the device with care and keep it in a clean and dust-free environment. Do not expose the device to extremely hot, cold or humid environment. The operation

temperature is from –10°C to 50°C. Do not use the device in wet or rainy conditions. Do not charge the device in extremely hot (> 40°C) or cold conditions (< 0°C). Do not attempt to disassemble or modify the device including the charger. Do not operate the device when your hands are wet. Do not insert foreign objects into the openings of the device. Use only the adaptor and battery approved for the device. The adapter shall be installed near the device and shall be easily accessible. Do not use the adaptor if the power cord or plug is damaged. Do not disassemble, crush or puncture the battery. Do not expose the battery to high temperatures. Do not let battery terminals touch other metal objects that could lead to short-circuit of the

battery. Do not dispose of the battery in fire or water. Dispose of used battery properly according to local laws and regulations. The device shall only be connected to a USB interface of version 3.0 or higher. The connection

to so called power USB is prohibited.

Battery Safety Charge battery only at ambient temperatures ranging from 40°C. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to battery manufacturer’s instructions. CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. CAUTION: Battery charging temperature upper limit is 40°C.

Adapter Safety When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 0°C~40°C. For altitude 2km below use only


Contents

Disclaimer ........................................................................................................................... 2

Regulatory Information ..................................................................................................... 3

Safety Information ............................................................................................................. 4 Battery Safety ............................................................................................................................................ 4 Adapter Safety ........................................................................................................................................... 4

1. Product Specifications ............................................................................................... 6

2. Getting Started ............................................................................................................ 9

2.1 Charging the Terminal .................................................................................................... 9 2.1.1 Charging with a USB charger ........................................................................................................ 9

2.2 Powering the Terminal On and Off ................................................................................ 9 2.2.1 Powering on the Terminal .............................................................................................................. 9 2.2.2 Powering off the Terminal .............................................................................................................. 9

2.3 Suspending the Terminal ............................................................................................... 9

2.4 Soft Reset ........................................................................................................................ 9

2.5 Fixing the Phone Strap ................................................................................................. 10

3. Using Wi-Fi................................................................................................................. 11

3.1 Connecting to a Wi-Fi Network .................................................................................... 11

3.2 Disconnecting from a Wi-Fi Network ........................................................................... 12

3.3 Disconnecting the Selected AP Name from a Wi-Fi Network Permanently ............... 12

4. Using BT .................................................................................................................... 13

4.1 Connecting a BT Device ............................................................................................... 13

4.2 Disconnecting a BT Device .......................................................................................... 14

4.3 Disconnecting the Selected AP Name from a Wi-Fi Network Permanently ............... 15

5. Using Cellular ............................................................................................................ 16

5.1 Inserting a SIM card ...................................................................................................... 16

5.2 Setting up Mobile Data ................................................................................................. 16

5.3 Disconnect Mobile Data ............................................................................................... 17

6. Using NFC .................................................................................................................. 18

6.1 Reading a NFC Tag ....................................................................................................... 18

6.2 Enable NFC ................................................................................................................... 18

6.3 Disable NFC .................................................................................................................. 19


1. Product Specifications

Function Technical Specifications CPU Model MT6761D CPU Feature Quad Core 1.8GHz Operating System Android 9.0 GO Battery 5200mAh ROM 16GB RAM 2GB LPDDR3 Display 5.45",HD+ IPS Touch Panel Technology 2 Points Primary Camera Type 5MP Barcode scanner E3 2D Barcode Scanner Buttons Power Button

Multi-function Button Microphone 1pcs Speaker 1pcs System I/O connector Type-C BT Ver 5.0 WLAN IEEE 802.11 ac/a/b/g/n, 2.4G/5G GPS Yes NFC Yes Printer 2" printer Thermal paper Width 57 mm, Diameter 40 mm Charger 1, 5V2A


Device Overview

No. Item Description

1 Earphone Jack Connect a stereo earphone

2 Volume Down Button

Compatible with the functions of code scanning and volume down adjustment

3 NFC Reader Scanning area for NFC tags

4 Indicator Lamp Used for indicating the steps for swiping card and charging state

5 Mic Mic in

6 Type-C USB Used for charging equipment and data transfer

7 Power Button

Short Press: Light the screen, lock the screen. Long Press: In shutdown state, long press 2-3 seconds to turn on; When in use, press 2-3 seconds for a long time, and you can choose to turn off, turn on or screen capture. In the crash state, press 10 seconds to restart automatically.

8 Volume up Button Compatible with the functions of code scanning and volume up adjustment

9 Extend Pins To connect to dock. (Need to buy dock separately)

A Phone Strap Phone Strap Hole

B Printer

Printing instructions This device supports 58mm thermal paper with the specifications of 57±0.5mmφ40mm ① Open the paper container ② Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter; ③ Close the cover of the paper container to finish printing paper feeding. Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.


C 2D Scanner Scan QR Code (Optional)

D Rear Camera Supports photographing and 1D/2D code quick scanning

E SIM Card Slot MicroSIM card slot (SIM 1 & SIM 2)

F Battery Connector Connect the battery

G Battery 3.6V 5200mAh battery


2. Getting Started

2.1 Charging the Terminal The terminal can be charged through the docking station or a USB adaptor.

2.1.1 Charging with a USB charger

1. Plug the USB charging cable supplied with the terminal into a USB charger. 2. Connect the other end of the USB charging cable into the Type 3 USB port of the terminal. 3. Plug the USB charger into a suitable power socket, and fully charge the terminal.

While charging, the device and the charger may become hot and stop charging. This usually does not affect the device’s lifespan or performance and is in the device’s normal range of operation. Disconnect the charger from the device and wait for the device to cool down.

2.2 Powering the Terminal On and Off

2.2.1 Powering on the Terminal

Press and hold the Power key for 3 seconds to power on the terminal.

2.2.2 Powering off the Terminal

Press and hold the Power key for 3 seconds, and follow the screen instructions to power off the device.

2.3 Suspending the Terminal

If the terminal is on, press the Power key once to suspend the device (i.e. entering sleep mode), saving battery power.

To resume operation from sleep mode, press the Power key once.

2.4 Soft Reset

Soft reset shuts down and reboots the device. It preserves installed applications, settings, and saved data. To perform a soft reset:

1. Open the rear cover. 2. Unplug the battery connector and plug in again. 3. The terminal shuts down and reboots.

Battery Connector


2.5 Fixing the Phone Strap An optional phone strap is available for the terminal. To fix the phone strap on the terminal: 1. Turn over the terminal. 2. Tight the phone strap into the phone strap hole


3. Using Wi-Fi

3.1 Connecting to a Wi-Fi Network

1. Go to “Settings”, choose ‘Network & Internet”, Choose WIFI and switch it on.

2. Select a network from the AP list, input the network password, and click Connect. Once connected, it displays Connected under the network name, also shows the WIFI symbol on the right top of the screen.


3.2 Disconnecting from a Wi-Fi Network

1. Go to “Settings”, choose ‘Network & Internet”, select WIFI and switch it off. 3.3 Disconnecting the Selected AP Name from a Wi-Fi Network Permanently

1. Go to “Settings”, choose ‘Network & Internet”, choose WIFI, your selected network shows connected. Click the select network and choose “Forget”, then it will not shown “Connected” on the AP list.

2. If needs to re-connect the previous AP after the above step is made, repeat step 4.1.


4. Using BT

4.1 Connecting a BT Device

To connect to a BT device: 1. Make sure the BT device is within range and set to be discoverable. 2. Go to “Settings”, choose ‘Connected Devices”, click “Visible as O1” to other devices”, the

select “BT”

3. Turn on the “BT”, select a device from the BT device list. A “BT pairing code” will appear on the terminal and the selected device, click “Pair” on both devices. Once paired, the connected device will shown on the “Currently connected” page.

Note: Some BT devices may require software driver installation.


4.2 Disconnecting a BT Device

To disconnect a BT Device: 1. Go to “Settings”, choose ‘Connected Device”, select “Connection Preferences”, Click “BT”

and switch it off.


4.3 Disconnecting the Selected AP Name from a Wi-Fi Network Permanently 1. Go to “Settings”, choose ‘Connected Device”, select “Previously Connected Device”, choose the

setting icon of connected device that needs to disconnect permanently, click “Forget” and “Forget Device”.


5. Using Cellular

5.1 Inserting a SIM card

1. Power off the terminal. 2. Open the rubber cover, remove the battery to locate the SIM card slot. 3. Insert the SIM card into SIM 1 or SIM 2 (Lower level is SIM 1, upper level is SIM 2)

4. Power on the terminal. 5.2 Setting up Mobile Data

1. Go to “Settings”, choose ‘Network & Internet”, turn on the “SIM Slot 1 or 2” that had installed the SIM card, enable the “Mobile Data” and “Automatically Select Network”.

2. Mobile data will be connect automatically


5.3 Disconnect Mobile Data

1. Go to “Settings”, choose ‘Network & Internet”, turn off the “SIM Slot 1 or 2”.


6. Using NFC

EC-AHT-O1 is equipped with an NFC controller operating at 13.56MHz for reading and writing NFC tags. It supports the following protocols: ISO 14443 A/B MIFARE Felica NFC Forum Tags ISO 15693 6.1 Reading a NFC Tag

NFC is turned on by default. To read a NFC tag, place the tag at approx. 2 cm from the NFC scanning area.

6.2 Enable NFC

1. Go to “Settings”, choose ‘Connected Device”, select “Connection Preferences”, Click “NFC” and switch it on.


6.3 Disable NFC 1. Go to “Settings”, choose ‘Connected Device”, select “Connection Preferences”, Click “NFC” and

switch it off.

- End of Document -


Manufacturer: EC LINE Thank you very much for using EC Line product For service, please contact [email protected]

www.eclinepos.com

www.ecline.com.hk

ec-aht-o1 user manual

Documents