STANDARD r

.nm

138mm I— with

spring 9.52mm —.. installed

HEAT SINK

MOUNTING — — 2.79mm

CLIP I — 1.38mm 6.22mm [1.. with

• spring

9.52mm

Left hand guide as viewed from insert end.

6.22mm

2.21mm—

--"."11FZI111111111.... O

SPRING GUIDE INSERT

2mm Lrl

3.8mm METRI—GUIDE (STANDARD)

100MM

120MM

' installed

THE METRI GUIDE Metri—Guide gives you all the Unitrack

quality and advantages in a metric card guide.

Mounting Centers start at 40 millimetters, increasing in 20 millimeters increments.

Standard Guide shown here, available in Heat Sink models see ordering information.

Spring finger insert is available in phosphor

bronze

ORDERING INFORMATION How to order Metri—Guide

Heat Sink Model

KG X X XXXX X

Metri—Gulde j-- i I --LL = Left Handed

Type of plating R = Right Handed Length In millemeters

0—NO FINISH 3—CLEAR ANODIZE (up to 1 meter) 1—CLEAR MITE 4—GOLD ANODIZE bOn 40mm 2=GOLD IRIDITE 5=ELACK ANODIZE 20mm increments

Spring Insert 1. P. = Phosphorus Bronze

Example : MG I P 120 would be an Assembly CLEAR IRIDITE, PHOSPHORUS BRONZE INSERT-100MM LG

with MOUNTING CENTERS 120MM

STUD MOUNTING AVAILAEIL.E. CONSULT FACTORY

Standard

MG X X )0CXX

Metri—Guide Type of plating

ONO FINISH 3—CLEAR ANODIZE 1=CLEAR IRIDITE 4=GOLD ANODIZE 2=GOLD IRIDITE 5=BLACK ANODIZE

—E.L.angth In manometers (up to 1 meter) Min 40mm 20mm increments Spring Insert

1. P. = Phosphorus Bronze

UNITRACK UNITRACK INDUSTRIES, INC. 967 E. Masten Circle, Milford, Delaware 19963 (302) 424-5050 • FAX (302) 424-5055 www.unitrackind.com

9

UIMITRACKUNITRACK INDUSTRIES, INC.967 E. Masten Circle, Milford, Delaware 19963(302) 424-5050 • FAX (302) 424-5055www.unitrackind.com

THE METRI GUIDEMetri—Guide gives you all the Unitrack

quality and advantages in a metric card guideMounting Centers start at 40 millimetters,increasing in 20 millimeters increments.

Standard Guide shownhere, available inHeat Sink modelssee ordering information.

SPRING GUIDE INSERT20mm-^

2mm

I

I

20nn 2,5mm

i2.25mm-

3r33

f3.8mm METRI-GUIDE (STANDARD)

ZD

-1 5nn--

3D ZD

O OC O

•100MM

120MM

Spring finger insertis available in phosphor

bronze

STANDARD

6.22mm j

9.52mm

1.38mm

J withspringinstalled

HEAT SINKI— 2.79mm

MOUNTING

^^.221^m

9.52mm

1.38mm

_l_ with-r- spring' installed

Left hand guideas viewed frominsert end.

ORDERING INFORMATION

Molri-Guide

Type of platingO-NO RNISH 3-CLEAR ANODIZE1=CLEAR IRIDITE 4=G0LD ANODIZE2=G0LD IRIDITE 5=BLACK ANODIZE

MG

.J

Stondord

X X XXXX

How to order Metri—Guide

^ngth In mtllamaters(up to 1 meter)Min 40mm20mm incremente

' Spring Insert1. P. = Phosphorus Bronze

Matrl-Gulde-

Type of plating0-NO FINISH 3-CLEAR ANODIZE1-CLEAR IRIDfTE 4-GOLD ANODIZEZsGOLD IRIDITE SaBLACK ANODIZE

Example : MG J_P 120 would be an AssemblyCLEAR IRIDITE, PHOSPHORUS BRONZE INSERT-100MM LG

wHh MOUNTING CENTERS 120MM

STUD MOUNTING AVAILABLE. CONSULT FACTORY

Heat Sink Model

KG X

JXXXX_ X

T_L = Left HandedR = Right Handed

txngth In mlllemeters(up to 1 meter)Min 40mm20mm Increments

- Spring Insert1. P. s: Phosphorus Bronze

.156

.125

t A__

f I I 1 -1- .150

.015 .095

ORDERING INFORMATION

.00' 0•0" 000r

I..-- 6.000

6.375

TRACK STYLE GROUND-R-GUIDE FURNISHED WITH MOUNTING CLIPS AS STANDARD

3/16"

11OLE 3/16" +.125/.128

°MEM MOUNTING CLIP

CATALOG No. MC1000 HOLES

OPTIONAL MOUNTING METHODS

STUD IfOUNTING

4-40 SS STUD I 1/4" LONG

U N IT R AC UNITRACK INDUSTRIES, INC.

e 967 E. Masten Circle, Milford, Delaware 19963 (302) 424-5050 • FAX (302) 424-5055 www.unitrackind.com

TM GROUND—R—GUIDE The Grounding Card Guide

OPEN STYLE The Ground—R—Guide, with spring finger action found only in UNITRACK card guides offers exceptional grounding features. The OPEN STYLE Ground—R—Guide can be mounted to a chassis or motherboard with rivets, using the holes provided in the

guide. Ground—R—Guide is available in three metals: phosphor bronze, stainless steel and beryllium copper.

FEATURES * The firm grip afforded by the

spring fingers develops a useful pressure contact over the length

of the p.c. cord for excellent electrical current passage.

* Large contact area of spring fingers provides a stable ground potential.

HOW TO ORDER

XX 1000 - XXX

Length in inches (in 1/2 in increments in sizes to 36 inches.)

Semi—hollow Aluminum Rivet

Catalogue No.1000R

TRACK STYLE

The TRACK STYLE Ground—R—Guide affords grounding for p.c. boards with the patented spring finger action found only in UNITRACK card guides. GB1008

Metal: PB=Phosphor Bronze BC-Beryllium Copper SS=Stainless Steel

Series

* TRACK STYLE Ground-R-Guide available for spanning open spaces. See below. Spring fingers give good shock and vibration damping.

* Available to exact lengths to customer specifications or in long lengths for customer cutting.

* Special assemblies also available.

FEATURES * Pressure developed by spring

fingers provides contact over entire length of p.c. card for excellent electrical current passage.

* Aluminum extrusion provides *

Metal: PB=Phosphor Bronze BC=Beryllium Copper SS=Stainless Steel

UN

Series J

rigid guide for spanning open areas (often required for air circulation or cooling). Available to hold 1/1 6" thru 1/8" p.c. cards. Spring fingers provide shock and vibration damping.

MOUNTING: (optional) H-Guide Bar with holes S=Guide Bar with studs

Length in inches (in 1/2 in increments in sizes to 36 inches.)

STANDARD SPACING OF AND STUDS

Guides up to 6 inches long-2 holes, or 2 studs spaced 1/2" from each end of the guide. Guides up to 10 inches long-3 holes, or 3 studs evenly spaced with the end holes or hardware 1/2" from each end of the guide. Guides over 10 inches long-4 holes, or 4 studs evenly spaced with the end holes or hardware 1/2" from each end of the guide. Longer guides, consult factory. Holes not available with Berylium Copper.

* Special placement (other than standard),consult factory

.173

.245 .045

1—.375

T

HOW TO ORDER xx

1008 - xx.x x

Type of Plating: 1 = Clear indite 2 = Gold indite 3 = Clear Anodize 4 = Gold Anodize 5 = Black Anodize

Example: UNSS1008-6 would be an assembled unit of: 6" long GB1008 Guide Bar; one 5.5" long SS1000 Stainless Steel card guide and two MC1000 mounting clips. Mounting hole centers would be 6.375 inches.

10

Thermal characteristics for two 6 inch long KOOLER-GUIDES type

KGPB375-6 holding an aluminium test card .060" thick x 4.5" wide x 6" long.

90

70

60

50

40

30

Tests prove the positive heat dissipating ability of the Kooler-Guide. The unique spring fingered configuration firmly pressing the P.C. card against the guide enables the heat to be more effectively reduced.

9 The solution to densely packaged

heat producing products.

The various mounting methods available increase the versatility of the Kooler-Guides.

.050

STANDARD SERIES KG375 Kooler-Guide with mounting clips hole dia. (±.003) .128

SERIES KG375-S Kooler-Guide with 4-40 X 1/4" long threaded S.S. Studs

.150—s1.120

.240

HOW TO ORDER

KG XX 375 - XX.X XX X

Kooler Guide

Metal: PB = Phosphor Bronze BC = Beryllium Copper SS = Stainless Steel

Series

Test Point B fi

.240

. Test Aluminium t Point A Test Card

Kooler Guide PB 1000 Insert

Kooler Guide

Metal: PB = Phosphor Bronze BC = Beryllium Copper

Card Insertion SS = Stainless Steel

Right Heat Sink

Tab Heat Sink

Tab Left

UNITRACK INDUSTRIES, INC. 967 E. Masten Circle, Milford, Delaware 19963

UNITRACK (302) 424-5050 • FAX (302) 424-5055 www.unitrackind.com

KOOLER-GUIDEP" U.S.Patent No. 4,096,547

UNITRACK'S KOOLER-GUIDE acts as a heat sink to effectively dissipate heat from "Hot" printed circuit cards. Metal fingers press the P.C. card into intimate contact with the guide bar over its entire length. This large contact area transfers the heat rapidly from the P.C. card to the Kooler-Guide and into the chassis or cold frame holding the guide.

Kooler-Guide is designed for P.C. cards .040" to .095" thick. The various mounting methods avail-able make the Kooler-Guide useful for almost any packaging or heat dissipation requirement.

-. TEMP. RISE OF KOOLER GUIDE AT POINT "R-- WITH C

I

RD IN KOOLER GUIDE

10 20 30 40 WATTS

LEFT HAND GUIDE VIEWED FROM INSERTION END

Heat Source

/ COLD FRAME AT AMBIENT TEMPERATURE

S = Stud Mounting (Optional)

L = Left handed R = Right handed

_Length in inches in V2 inch increments.

Type of Plating: 1 = Clear Iridite 2 = Gold Iridite 3 = Clear Anodize 4 = Gold Anodize 5 = Black Anodize

The Kooler-Guide insert is available in your choice of the following:

• PHOSPHOR BRONZE (PB) • STAINLESS STEEL (SS) • BERYLLIUM COPPER (BC)

Standard spacing of holes, studs or swage nuts.

• Guides up to 6 inches long - 2 holes, 2 studs or 2 swage nuts spaced 1/2" from each end of the guide.

• Guides up to 10 inches long - 3 holes, 3 studs or 3 swage nuts evenly spaced with the end holes or hardware 1/2" from each end of the guide.

• Guides over 10 inches long - 4 holes, 4 studs or 4 swage nuts evenly spaced with the end holes or hardware 1/2" from each end of the guide.

• Holes not available in Beryllium Copper for series 375.

Dimensions in inches. Tolerance: All dimensions under 6" • .010: over 6" • .020.

SERIES KG690-H Kooler-Guide mounting flange with .136 dia. holes.

SERIES KG690-N Kooler-Guide mounting flange with 4-40 threaded swage nuts.

.4— .375 —li .690

Card Insertion

Series TO ORDER RIGHT OR LEFT HAND GUIDES -

Add letter to end of catalog number, L=Left, R =Right. When viewed from the entry end, the heat sink tab signifies right or left.

HOW TO ORDER

XX.X Type of Plating:

1 = Clear Iridite 2 = Gold Iridite 3 = Clear Anodize 4 = Gold Anodize 5 = Black Anodize

11

L = Left handed R = Right handed

—Length in inches in V, inch increments.

H = Mounting Flange with holes

N = Mounting Flange with swage nuts

UIMITRACK

UNITRACK INDUSTRIES, INC.967 E. Masten Circle, Milford, Delaware 19963(302) 424-5050 • FAX (302) 424-5055www,unitrackind.com

KOOLER-GUIDEU.S.Patent No. 4,096,547

UNITRACK'S KOOLER-GUIDE acts as a heat sinkto effectively dissipate heat from "Hot" printedcircuit cards. Metal fingers press the P.C. cardinto intimate contact with the guide bar over itsentire length. This large contact area transfersthe heat rapidly from the P.C. card to the Kooler-Guide and into the chassis or cold frame holdingthe guide.

Kooler-Guide is designed for P.C. cards .040" to.095" thick. The various mounting methods available make the Kooler-Guide useful for almostany packaging or heat dissipation requirement.

Thermal characteristics for two 6 inch long KOOLER-GUIOES type

KGPB375-6 holding an aluminium test card .060" thick x 4.5" wide x6" long.

Tests prove the positive heat dissipating ability of the Kooler-Guide. The unique springfingered configuration firmly pressing the P.C. card against the guide enables the heatto be more effectively reduced.

The solution to densely packagedheat producing products.

- -

The various mounting methods availabie Increase the versatility of the Kooler-Guides.

-I—

•H

LEFT HAMD CUlOE VIEWEDFROM INSERTION END

STANDARD

SERIESKG375Kooler-Guide

with mounting clipshole dia. (±.003) .128

SERIES

KG375-SKooler-Guide

with 4-40 X Va"longthreaded S.S. Studs

. Tc«tf Point A '

. AiuminkumTe«t Cord HOW TO ORDER

COLD FRAME AT AMBIENT TEMPERATURE

The Kooler-Guide insert is available inyour choice of the following:

• PHOSPHOR BRONZE (PB)• STAINLESS STEEL (88)• BERYLLIUM COPPER (BC)

Standard spacing of holes, studs or swage nuts.

• Guides up to 6 inches long - 2 holes, 2 studs or 2 swagenuts spaced V?" from each end of the guide.

• Guides up toiO inches long-3 holes, 3 studs or 3 swagenuts evenly spaced with the end holes or hardware Vz"from each end of the guide.

• Guides overlO inches long - 4 holes, 4 studs or 4 swagenuts evenly spaced with the end holes or hardware Vz"from each end of the guide.

• Holes not available in Beryllium Copper for series 375.

Dimensions in incnes.

Tolerance: All dimensions under

6' • .010: over 6" - .020.

Kooler Guide

Metal:PB s Phosphor BronzeBC = Berylllum CopperSS = Stainless Steel

U-1/2"

SERIES

KG690-HKooler-Guide

mounting flange with.136 dia. holes.

I S = Stud Mounting(Optional)

L= Left handedR = Right handed

.Type of Plating:1 = Clear Irfdite2 = Gold Iridite3 = Clear Anodize

4 = Gold Anodize

5 = Black Anodize

Length in inchesin 'A Inch increments.

SERIES

KG690-NKooler-Guide

mounting flangewith 4-40 threaded

swage nuts.

Heat Sink

Tab

Heat Sink

Tab HOW TO ORDER

IL

TO ORDER RIGHT OR LEFT HAND GUIDES -

Add letter to end of catalog number, L=Left, R = Right.When viewed from the entry end, the heatsink tab signifies right or left.

Kooler Guide

Metal:PB = Phosphor BronzeBC = Beryllium CopperSS = Stainless Steel

Type of Plating:Mounting Flange 1 = Clear Iriditewith holes 2 = Gold Iriditewith holes 2 = Gold Indite

N= Mounting Flange 3 s Clear Anodizewith swage nuts 4 = Gold Anodize

I—L = Left handedR = Right handed

Length in inchesin A inch Increments.

5 = Black Anodize

UNITRACK SERIES 4700 U.S Patent 3.950.057

SERIES 4700

The Series 4700 UNITRACK Card Guides incorporate the patented* spring finger action of UNITRACK Card Guides to accommodate p.c. cards up to 6' long! Now "big" boards can be held with the card guide that provides vibration and shock damping for p.c. cards 1/16" to 1/8" thick. Dimensionally stable polycarbonate plastic segments are simply slid into the guide bar to make any length card guide needed. Mounting clips lock the segments within the guide bar, as well as provide a positive mounting method. Other special mounting arrangements are available, such as bonding, rivet-ing, etc.

Series 4700 UNITRACK Card Guides are available as assemblies to exact lengths or as individual parts to be assembled by the customer. Although many large p.c. cards are mounted to a solid chassis, the rigid guide bar makes it possible to easily span open spaces.

I

Segments slide into guide bar to make any length card guide.

OPTIONAL MOUNTING METHODS Guide bar with flange and mounting holes. Also available but not shown is guide bar with flange and swage nuts.

Spring finger segment of polycarbonate.

/ .230

Mounting clips lock in segments and provide mount-ing holes at each end.

.255 r G-

300 060

J-1

,-- 495

Guide Bar GB4718 Recommended for board thickness .060"-.140"

125 128 dia

— F- 11 385

- 190 1/4" to start of first segment — .375 --

Mounting Clip Cat. No. MC4700

Part Cat. No.

8" Segment SG4700-8

NOTE: Length of Guide bar is 1/2" longer than Dash No. Mounting hole dimensions are .875" longer than Dash No.

Example: UN4718-14 would be an assembled unit of: One GB4718 fourteen and one half inches long, SG4700 segments and two MC4700 mounting clips. Mounting hole dimensions would be 14.875 inches.

Mounting Clip

MC4700

Dash Mounting No. Hole Centers

Standard spacing of holes, studs or swage nuts.

• Guides up to 6 inches long - 2 holes, 2 studs or 2 swage nuts spaced '/2" from each end of the guide.

• Guides up to 10 inches long - 3 holes, 3 studs or 3 swage nuts evenly spaced with the end holes or hardware 1/2" from each end of the guide.

• Guides over 10 inches long - 4 holes, 4 studs or 4 swage nuts evenly spaced with the end holes or hardware 1/2" from each end of the guide.

TO ORDER RIGHT OR LEFT HAND GUIDES - Add letter to end of catalog number, L=Left, R=Right.

Basic Cat. No.

Snap-in Rivet RV4700

Guide Bar GB4718

Guide bar with flange FL4718

Specify Left or Right

Dash OPTIONS FOR No. UNFL4718

Basic Cat. No.

.255 r

E 300 .060

I S .

—77-7 ,-- .495 ---- .495

Guide Bar FL4718 Guide bar with flange (Specify holes -H or flange nuts -N) Recommended for board thickness .060‘" - .140"

-H = Holes -N = Swage Nuts -L = Left -R = Right

UN4718 UNFL4718

Dimensions in incnes. Tolerance: All dimensions under 6' -t.010: over 6" .020.

12

-6

6.875" -8

8.875" -10

10.875" -12

12.875" -14

14.875" -16

16.875" -18

18.875" -20

20.875"

-6 - 8 -10 -12 -14 -16 -18 -20

X

.110 INSERT I .

1095

4 - 40 STUD X 1/4"

UN PL

SERIES-

PLASTICS

INSERT

END

VIEW

.187- —.375

X+.375

X

UNPL2008 WITH STUDS OR WITH CLIPS Aluminum strength with the insulation of polycarbonate available with studs or clips, for ease of installation, studs can be placed to suit your cage.

ORDERING INFORMATION

h7— —7-0.50 --1-1

0.375 C •

CLIPS

AS REQ.

INSERTS (LINERS) P2000

X x

MOUNTING: (optional) C=Clips S=Guide Bar with studs

LENGTH IN INCHES (to 36 inches)

Example: UNPL2008-6 would be an assembled unit of: 6" long GB1008 Guide Bar; one 5.5" long PLASTIC INSERT and two MC1000 mounting clips. Mounting hole centers would be 6.375 inches.

STANDARD SPACING OF CLIPS AND STUDS

Guides up to 6 inches long-2 clips, or 2 studs spaced 1/2" from each end of the guide. Guides up to 10 inches long-2 clips, or 3 studs evenly spaced with the end holes or hardware 1/2" from each end of the guide. Guides over 10 inches long-2 clips, or 4 studs evenly spaced with the end studs or hardware 1/2" from each end of the guide. Longer guides, consult factory.

STUDS

HOW TO ORDER 2008 - XX.X

TYPE OF PLATING 1-Clear Iriclite 2-Gold Iridite 3-Clear Anodize 4-Gold Anodize 5-Black Anodize

* Special placement (other than standarcaconstat factory

13

UNPL2008WITH STUDS OR WITH CLIPSAluminum strength with theinsulation of polycorbonateavailable with studs or

clips, for ease ofinstallation, studscon be placedto suit yourcage.

ORDERING INFORMATION

INSERT-| |- .110

J^-095HOW TO ORDER

PL 2008 - XX.X

END

VIEW

.187-

0.375 iSL

4-40 STUD X 1/4"

-.375

STUDS

X+.375

CLIPS

AS REQ.

INSERTS (LINERS)P[2000

SERi

PLASTICS

INSERT

UN X

TX

11-MOUNTING: (optional)C=CiipsS=6utde Bar wrth studs

— LENGTH IN INCHES(to 36 inches)

-TYPE OF PLATING1-Clear Irldlte

2-Gold Indite3-Cl8ar Anodize

4-Gold Anodize5-Black Anodize

Example: UNPL2008-6 would be anassembled unit of: 6" long GB1008Guide Bar; one 5.5" long PLASTICINSERT and two MC1000 mountingclips. Mounting hole centers wouldbe 6.375 inches.

STANDARD SPACING OF CUPS

AND STUDSGuides up to 6 inches long-2 clips, or 2 studsspaced 1/2" from each end of the guide.Guides up to 10 inches long-2 clips, or 3 studsevenly spaced with the end holes or hardware 1/2"from eoch end of the guide.Guides over 10 inches long-2 clips, or 4 studsevenly spaced with the end studs or hardware 1/2'from each end of the guide.Longer guides, consult factory.

:4c Special placeTnejit (other than standard),consult factory

13