skee2413 on induction motor [compatibility mode]
DESCRIPTION
MotorTRANSCRIPT
Chapter 4.
Three-phase Induction Machines
Introduction The induction machine is the most rugged and
the most widely used machine in industry. Both stator and rotor winding carry alternating
currents. The alternating current (ac) is supplied to the
stator winding directly and to the rotor winding by induction – hence the name induction machine.
Application (1-phase): washing machines, ceiling fans, refrigerators, blenders, juice mixers, stereo turntables, etc.
2-phase induction motors are used primarily as servomotors in a control system.
Application 3-phase: pumps, fans, compressors, paper mills, textile mills, etc.
Induction Machine
Construction
Construction
Unlike dc machines, induction machines have a uniform air gap. The stator is composed of laminations of high-grade sheet steel.
A three-phase winding is put in slots cut on the inner surface of the stator frame.
The rotor also consists of laminated ferromagnetic material, with slots cut on the outer surface.
Squirrel-cage Rotor
Wound Rotor
Wound rotor
Slip ring
Construction
The three-phase winding are displaced from each other by 120 electrical degrees in space
Current flows in a phase coil produce a sinusoidally distributed mmf wave centered on the axis of the coil.
Alternating current in each coil produces a pulsating mmf wave. Mmf waves are displaced by 120 degrees in space from each other. Resultant mmf wave is rotating along the air gap with constant peak.
Cross-sectional view Y-connected stator ∆-connected stator
Induction Motor Operation
RMF – rotating magnetic field
Rotating Magnetic Field – consider 2-pole machine
a) Three phase stator winding, aa’, bb’ and cc’ displaced by 120o.
b) Mmf (pulsating) in space at various instants due to a.c current in coil aa’
c) Instantaneous 3 phase current
a. Graphical Method – Resultant mmf (magnitude and direction)
Resultant mmf
Mmf phase a
at t = t0= t4
Graphical Method
Constant amplitude, move around the air gap
n = synchronous speed
f = f1= supply freq.,
p = no of polesrpm
pairs pole p ; radsf2
rad/sin speed sSynchronou
1-11 ===
ppe πωω
b. Analytical Method
Motion of the resultant mmf
N = effective number of turns
ia= current in phase ‘a’
Analytical Method
Induced Voltages
where r = radius of the stator; ι = axial length of stator
A
Induced Voltages
V per phase
At Standstill operation
E1 = 4.44f1N1ΦpKw1
E2 = 4.44f2N2ΦpKw2 ; f1 = f2
E2 = 4.44f1N2ΦpKw2
Running Operation
120
pnf =
at slip s
* E2 – induced rotor voltage at standstill
frequency slip :
pair pole :
frequencyrotor :
frequencysupply :
frequency ssynchronou :
:where
)1(
; s ;
radsin edreprensent beCan
2
2
-1
ω
ωωω
ωω
ωωωω
ωωω
p
s
ps
m
e
s
sm
es
ss
ms
−=
==−=
Example 1
A three-phase, 100 hp, 460 V, four-pole, 60 Hz induction machine delivers rated output power at a slip of 0.05. Determine the
(a) Synchronous speed and motor speed.(b) Speed of the rotating air gap field.(c) Frequency of the rotor circuit.(d) Slip frequency (in rpm).(e) Speed of the rotor field relative to the
(i) rotor structure(ii) stator structure(iii) stator rotating field
(f) Rotor induced voltage at the operating speed, if the stator-to-rotor turns ratio is 1:0.5
Pg 219: 1800 &1710rpm, 1800rpm, 3 Hz, 90 rpm, (90rpm, 1800rpm, 0rpm), 6.64 V/ph)
Sol_pg21
Equivalent Circuit Model
• To study and predict the performance of the induction machine
Equivalent Circuit Model
Equivalent Circuit Model
Induction Motor Drives SEE4433 Dr Zainal / Dr Awang
25
Stator voltage equation:
V1 = R1 I1 + j(2πf)LlI1 + Eag;
Eag – air gap voltage or back e.m.f
Eag = E1 = k f1 φag
Rotor voltage equation:
E2 = R2 I2 + js(2πf)Ll2
E2 = k f2 φag = k sf1 φag = sE1
E2 – induced emf in rotor circuit ; E1=R2/sI2+j2πfLI2
Equivalent Circuit Model
Equivalent Circuit Model
sE2 – rotor voltage at standstill
Equivalent Circuit Model
This model is not convenient to use to predict
circuit performance
Equivalent Circuit Model
Example 2
A three-phase, 15 hp, 460 V, four-pole, 60 Hz, 1728 rpm induction motor delivers full output power to a load connected to its shaft. The windage and friction loss of the motor is 750 W. Determine the
(a) mechanical power(b) air gap power(c) rotor copper loss.
Pg 226: 11940 W, 12437.5 W, 497.5 W
Sol_pg29
Equivalent Circuit Model
Assume small volt
drop across R1and X1 – ease computation of IΦ and I2’,
V1 = E1
Due to machine air gap, IΦ is high- 30-50% of full –load
current, X1 is high, core loss (Rc) is lumped into the
mechanical losses
Equivalent Circuit Model
R12<<(X1+Xm)2
X1 << Xm
For simplification, replace V1, R1,X1, Xm with Vth, Rth, Xth ( at terminal Pag)
Equivalent Circuit ParametersRc, Xm, R1, X1, X2, R2
No-Load Test The parameters of the equivalent circuit, Rc, Xm, R1, X1,
X2, and R2 can be determined from the results of a no-load test, a blocked-rotor test and from measurement of the dc resistance of the stator winding.
The no-load test, like the open circuit test on a transformer, gives information about exciting current and rotational losses.
This test is performed by applying balanced polyphase voltages (415V) to the stator windings at the rated frequency(50Hz).
The rotor is kept uncoupled from any mechanical load.
R1 X1
Xm
I1
cctopen 0
R
s
R
0;N
NNs
NN load, noAt
22
s
rs
sr
→∞==∴
=−=
≈
Blocked-Rotor Test The blocked-rotor test, like the short-circuit test on a
transformer, gives information about leakage impedances. In this test the rotor is blocked so that the motor cannot rotate,
and balanced polyphase voltages are applied to the stator terminal ( increases voltage until stator current reaches its rated value).
The blocked-rotor test should be performed under the same conditions of rotor current and frequency that will prevail in the normal operating conditions.
The IEEE recommends a frequency of 25% of the rated frequency for the blocked-rotor test. However, for normal motors of less than 20 hp rating, the effects of frequency are negligible and the blocked-rotor test can be performed directly at the rated frequency
cctopen , 1
R
s
R
1;N
NNs
;0N ),rotor test(block load fullAt
222
s
rs
r
2 mm XXRR ⟨⟨→==∴
=−=
=
R1 X1 X2
R2
Equivalent Circuit Parameters Measurement of average dc resistance per stator
phase : R1
No load test :VNL
INL
PNL
Blocked-rotor test:VBL
INL
PNL
Example 3 The following test results are obtained from a three-phase, 60 hp, 2200 V,
six-pole, 60 Hz squirrel-cage induction motor. No-load test:
supply frequency = 60 HZline voltage = 2200 Vline current = 4.5 Ainput power = 1600 W
Blocked-rotor test:frequency = 15 Hzline voltage = 270 Vline current = 25 Ainput power = 9000 W
Average DC resistance per stator phase:R1 = 2.8 ohm
(a) Determine the no-load rotational loss.(b) Determine the parameters of the IEEE-recommended equivalent circuit.(c) Determine the parameters (Vth, Rth, Xth) for the thevenin equivalent circuit.
Pg: 230: 1429.9 W Sol_pg38(IM)
Performance Characteristics
Induction Motor Drives SEE4433 Dr Zainal / Dr Awang
40
Performance calculation using SPEC
22
2
22
2
21
12
1
11
11
3 :losscopper Rotor
3 :gap-air theacrossPower
3 :loss Core
3 :losscopper Stator
current and voltagephase bemust and :Note
cos3 :PowerInput
RIPPPP
s
RIP
R
VP
RIP
IV
IVP
lr
lclsin
g
mlc
ls
in
=−−=
=
=
=
= φ
I 1 R1 L 1
V 1 Rm L m
L 2
R2
S
I 2
s
RsIPT
PPPP
sPs
sRII
s
RI
PPP
mm
oe
FWFWosh
g
lrgo
ωω2
22
22
22
22
22
2
)1(3
: torquegnetic)(electroma Developed
loss. windageandfriction : ;
:shaft at thePower
)1()1(3
R33
:poweroutput Gross
−==
−=
−=−=−=
−=
s
RpIT
p
s
RIT
ss
ee
ee
e
mm
22
2
1
2
1
22
11
1
3
Then,
frequency.supply theis ;But
3
,)1(
Since
ω
ωωω
ω
ωωω
ωω
=⇒
=
=∴
−=⇒−=
ExampleA single phase equivalent circuit of a 6-pole SCIM thatoperates from a 220 V line voltage at 60 Hz is given below.Calculate the stator current, input power factor, outputpower, torque and efficiency at a slip of 2.5%. The fixedwinding and friction losses is 350 W. Neglect the core loss.Also calculate the starting current.
Solution
I1 R1 X1
V1 Xm
X2
R2
I2
0.2Ω 0.5Ω
20Ω 0.1Ω
0.2Ω
1V 220V line-to line 3
220V 127V
3 2.5% 0.025
= ÷
= =
= =
mN
sp
PPT
WPPP
WsPP
W
PPP
WRIP
W
IVP
AZ
VI
jj
jjj
jXs
RjXjXRZ
XXX
e
o
m
oe
FWosh
go
lsing
ls
oin
oo
in
o
min
m
.4.78
)025.01)(3/60(2
9611
)1()(
Torque neticElectromag
%3.8910758
9611
powerInput
powerOutput Efficiency
611,9350961,9
shaft at thePower
961,9)025.01(216,10)1(
power Gross
216,10 540758,10
loss) core g(neglectinrotor tosferredPower tran
540)2.0)(30(33
758,10
)20)(cos30)(3220(3cos3
200.30202.4
3220
202.4202.0
025.01.0
2.0025.01.0
205.02.0
//)(
20,2.0,5.0
1
21
21
11
11
22
11
21
=−
=−
==
===
=−=−=
=−=−=
=−=
−=
===
===
−∠=∠
==
Ω∠=
++
+++=
+++=
Ω=Ω=Ω=
πωω
φInput power
factor
motors.induction starting taken whenbe should emotors.Carinduction for common is This
current. load full than times5about iscurrent starting that theNote
16776.0
322076.0
202.01.02.01.0
205.02.0
1 ,standstillAt :Solution
11 A
Z
VI
jj
jjjZ
s
in
in
===
Ω=
++
+++==
=
The following results were obtained on a 3 phase, starconnected stator, 75 kW, 3.3 kV, 6-pole, 50 Hz squirrel-cageinduction motor.
No-load (NL) test: Rated frequency, 50 HzVNL = 3.3 kV (line), INL = 5A, PNL = 2500 W
Blocked-rotor (BR) test: Frequency 50 HzVBR = 400 V (line), IBR = 27 A, PBR = 15000 W
DC test on stator resistance per phase = 3.75Ω.
i) Determine the parameters of the IEEE recommended equivalent circuit.
ii) Find the parameters of the Thevenin equivalent circuit as seen from the rotor circuit.
iii) For a slip of 4%, calculate the stator current, power factor and efficiency of the motor.
Example
Sol_pg46