nic 510 and meter labeling product requirements...nic 510 and meter labeling product requirements 23...

NIC 510 and Meter Labeling Product Requirements 23 December 2015 Silver Spring Networks 1

Silver Spring Networks

555 Broadway Street

Redwood City, CA 94063

www.silverspringnet.com

NIC 510 and Meter Labeling Product Requirements

http://www.silverspringnet.com

Confidential Information of Silver Spring Networks®, Inc., provided under nondisclosure obligations.

Copyright © 2015 Silver Spring Networks, Inc. All rights reserved.

The following are registered trademarks of Silver Spring Networks, Inc: the Silver Spring Networks name and logo, Altogether Brilliant®, Connect to the Energy Network®, CustomerIQ®, GreenBox®, GridScape®, Micromesh®, Power Over Energy®, Silver Spring®, Silver Spring Networks (and design)®, UtilityIQ®, UtilOS®.

The following are trademarks of Silver Spring Networks, Inc: Connect to The Everything Network™, EnergyIQ™, Gen™, GreenIQ™, MicroAP™, Milli™, NetworkIQ™, OPSIQ™, Rings Logo™, SensorIQ™, SilverLink™, Streetlight.Vision™, The Internet of Important Things™.

All other company and product names are used for identification purposes only and may be registered trademarks, trademarks, or service marks of their respective owners.

Please consider the environment before printing this document.


NIC 510 and Meter Labeling Product Requirements

Customer Support

Telephone Hours Email

Toll free within the US and Canada:1-888-SSN-9876(1-888-776-9876)

Non-toll-free: 1-650-839-4298

5:00 AM - 6:00 PM US Pacific Time

[email protected]

In Australia:1300 706 769

9:00 AM - 9:00 PMAustralia Eastern Time

[email protected]

Contact us on the Web: http://www.silverspringnet.com/services/customer-support/

Contact us. Email [email protected] with suggestions or corrections for this or any document.

mailto:[email protected]

mailto:[email protected]

http://www.silverspringnet.com/services/customer-support

mailto:[email protected]?Subject=Documentation%20Suggestion

NIC 510 and Meter Labeling Product Requirements 1 About the Silver Spring Networks Network Interface Card, NIC 510

1 About the Silver Spring Networks Network Interface Card, NIC 510

The Silver Spring Networks NIC 510 is a network interface card that enables

machine-to-machine communication over 900 MHz and 2.4 GHz ISM bands.

ReferencesGuidelines for 64-bit Global Identifier (EUI-64™) Registration Authority, IEEE Standards

Association.

Figure 1. Silver Spring meter NIC



NIC Address LabelingFor radio identification, the host device shall have an auxiliary label containing the Silver

Spring Networks NIC address presented in text (16 alphanumeric digits) and bar code

formats.

• Bar Code Type = Code 3 of 9

• Bar Code Font Size = unknown

• Font Type = unknown

• Font Size = unknown

• Bar Code Label Dimensions = 1.0ʺ x 1.5ʺ

• Bar Code Material Type = Static Dissipative Polyimide

Figure 2 shows an example of the NIC address label, which is consistent with FCC

requirements set forth in FCC and Industry Canada Guidelines for Devices Containing a

Transmitter Module on page 7, and contains the Silver Spring Networks corporate name and

NIC EUI-64 address.

NIC Labeling The Silver Spring Networks meter NIC has two labels relevant to meter final assembly and

RMA: the FCC and Part Number label and the Silver Spring NIC address label. Both labels

are located on the bottom side of the NIC PCA.

The FCC ID label is 1ʺ x .375ʺ inches (2.5 x 1 cm).

Figure 3 shows an example of the FCC ID label found on the meter NIC.

Figure 2. Example of NIC address label for NIC510

Figure 3. Sample FCC ID label for meter NIC510

Silver Spring Networks1234567890123456

Contains: FCC ID: OWS-NIC511-03IC: 5975A-NIC51103



Figure 4 shows the placement of the labels.

Figure 4. Label locations on the Silver Spring meter NIC

Catalog number Model number FCC ID IC Certification

Silver Spring MAC address

Silver Spring part number


NIC 510 and Meter Labeling Product Requirements 2 FCC and Industry Canada Government Guidelines

2 FCC and Industry Canada Government Guidelines

Silver Spring Networks meter NIC

FCC ID: OWS-NIC511-03

IC: 5975A-NIC51103

RequirementsThe Silver Spring Network meter network interface card (NIC) is REQUIRED to be

professionally installed by a properly trained technician. Improper installation could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

The antenna of this transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

The device should be installed so that people will not come within the specified distance of

the antenna as listed below.

US installations: The device should be installed so that people will not come within 20

cm (8 in.) of the antenna.

Canada installations (IC): The device should be installed so that people will not come

within 29 cm (11.4 in.) of the antenna.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Table 1. NIC models

Model No.900 MHz

2.4 GHz

Internal Antenna

Off-Board Antenna FCC ID IC ID

NIC 511-0303 x x x x

OWS-NIC511-03 5975A-NIC51103NIC 511-0302 x x x

NIC 511-0301 x x x



This equipment has been tested and found to comply with Part 15 of the FCC Rules. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception (which can be determined by turning the equipment off and on), the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Exigences d'Industrie CanadaLa carte d’interface réseau (NIC) Silver Spring Network Relay Point (NRP) DOIT être

installée par un technicien ayant reçu une formation adéquate. Une installation incorrecte

peut annuler l’autorisation de l’utilisateur à se servir de l’équipement.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et.

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

L’antenne de cet émetteur ne doit pas se trouver à proximité de ou fonctionner en association

avec une autre antenne ou un autre émetteur.

Lʹappareil doit être installé de telle sorte que les gens ne viendront pas au sein de 29 cm (11.4

in.) de lʹantenne.

Les changements ou modifications apportés sans l’approbation expresse de l’autorité

responsable de la conformité pourront entraîner l’annulation de l’autorisation d’utilisation

de cet équipement.

FCC and Industry Canada Guidelines for Devices Containing a Transmitter Module

The following is an extract from FCC PART 15 UNLICENSED MODULAR TRANSMITTER

APPROVAL, DA 00-1407, Released: June 26, 2000, Section 6 describing labeling requirements

for devices containing a modular transmitter.

Section 6. The modular transmitter must be labeled with its own FCC ID number, and, if

the FCC ID is not visible when the module is installed inside another device, then the

outside of the device into which the module is installed must also display a label

referring to the enclosed module. This exterior label can use wording such as the

following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID:

XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The

Grantee may either provide such a label, an example of which must be included in the



application for equipment authorization, or, must provide adequate instructions along

with the module which explain this requirement.

In the latter case, a copy of these instructions must be included in the application for

equipment authorization.

The following is an extract from RSS-GEN, General Requirements and Information for the

Certification of Radio Apparatus, Section 3.2.1, describing labeling requirements for a host

device integrating a radio module.

The host device shall be properly labelled to identify the modules within the host device.

The Industry Canada certification label of a module shall be clearly visible at all times when

installed in the host device, otherwise the host device must be labelled to display the

Industry Canada certification number of the module, preceded by the words “Contains

transmitter module”, or the word “Contains”, or similar wording expressing the same

meaning, as follows:

Contains transmitter module IC: XXXXXX-YYYYYYYYYYY

where XXXXXX-YYYYYYYYYYY is the moduleʹs certification number.

L’extrait suivant provient du Cahier des charges sur les normes radioélectriques (CNR);

exigences générales et information relatives à la certification des appareils radio, section

3.2.1, et décrit les exigences en matière d’étiquetage pour un dispositif hôte intégrant un

module radio.

Le dispositif hôte doit être correctement étiqueté afin d’identifier les modules qu’il

comprend.

L’étiquette de certification Industrie Canada d’un module doit toujours être bien visible lors

de l’installation sur un dispositif hôte. Dans le cas contraire, le dispositif hôte doit être

étiqueté de façon à afficher le numéro de certification Industrie Canada du module, précédé

de l’expression « Contains transmitter module » ou du mot « Contains », ou d’une

formulation similaire ayant la même signification. Par exemple :

Contains transmitter module IC : XXXXXX-YYYYYYYYYYY

où XXXXXX-YYYYYYYYYYY représente le numéro de certification du module.

The applicant for equipment certification of the module shall provide with each unit of the

module either a label such as described above, or an explanation and instructions to the user

as to the host device labelling requirements.

Figure 5. Sample FCC ID label for devices containing a NIC (NIC510)

Model: NIC 511-0303

Contains FCC ID:OWS-NIC511-03 IC:5975A-NIC51103



NIC 510 External Antenna IntegrationThis radio transmitter 5975A-NIC51103 has been approved by Industry Canada to operate

with the antenna types listed Table 2 with the maximum permissible gain and required

antenna impedance for each antenna type indicated. Antenna types not included in this list,

having a gain greater than the maximum gain indicated for that type, are strictly prohibited

for use with this device.

Cet émetteur radio 5975A-NIC51103 a été approuvé par Industrie Canada pour fonctionner

avec les types dʹantenne énumérés dans le tableau 1 ci-dessous avec le gain maximal

admissible et lʹimpédance dʹantenne requise pour chaque type dʹantenne indiqué. Les types

dʹantennes ne figurant pas dans cette liste, ayant un gain supérieur au gain maximum

indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil.

Under Industry Canada regulations, this radio transmitter may only operate using an

antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry

Canada. To reduce potential radio interference to other users, the antenna type and its gain

should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour

l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son

gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Safety Information

Careful planning of every job is essential. Nothing should be taken for granted. Do not take

chances!

• Read and follow all approved policies and procedures provided by your employer

associated with the procedures in this manual.

• The procedures in this manual must only be performed by qualified workers in

accordance with local utility safety practices, utility requirements, and applicable OSHA

and NFPA standards.

Table 2. Antenna types

Antenna Type 900 MHz Gain (dBi) 2.4 GHz Gain (dBi)Antenna Impedance

Omni Directional 3 4.5 50

Wrap Around 1 3.5 50

XXX WARNING: Severe shock and explosion hazard! Touching energized parts can result in massive equipment damage, and severe injury or death. Short-circuiting energized parts will result in blinding flash and explosion. Opening and closing electrical circuits can also produce dangerous and explosive arc flashes. Involuntary muscular reactions associated with electrical shock may result in other injuries. Observe the following safety guidelines.



• The information contained in this document is intended to aid qualified personnel, and is

not a replacement for the proper training required to make a person qualified.

• Silver Spring Networks assumes no liability for the customerʹs failure to follow these

safety guidelines.

General Electrical Safety• Perform the procedures in this manual in accordance with applicable workplace

standards established by the following agencies:

— Occupational Safety and Health Act (OSHA).

— The National Electrical Code published by the National Fire Protection Association

(NFPA-70).

— National Electrical Manufacturers Association (NEMA).

— Electronics Industries Association (EIA).

— Insulated Power Cable Engineers Association (IPCEA).

• American National Standards Institute (ANSI). Whenever possible, de-energize all

circuits or equipment before working on them.

• Maintain a minimum clearance of 10 feet (3 meters) between line potential and all

unqualified persons at all times.

• Keep unauthorized people out of the work area. Be especially cautious of children, who

tend to be drawn to work activity.

• Determining if a circuit is OFF can be difficult in some instances. Check for circuit voltage

with an appropriate voltmeter before working on equipment presumed to have been de-

energized. Tiebreakers, double throw disconnect switches, automatic transfer switches

and emergency generators can supply power through an alternate circuit or from another

source.

• 120V current can be just a lethal as higher voltages because current flow through a body

depends upon the bodyʹs resistance.

• Do not trust insulation and/or weatherproofing on a wire as protection from shock.

• Use electrically insulated tools. Inspect portable electrical equipment or tools for defects

and remove any defective devices from service immediately. All portable electrical

equipment must have Ground Fault Circuit Interrupter (GFCI) protection.

• Select the right tool for the job. Use tools properly. Keep tools in good working order.

• Make sure the work area is free of any flammable material. Flammable vapors can be

ignited by an arc flash.

• Keep the work area clean and dry. Cluttered work areas cause accidents and injuries.

• Provide good lighting in the work area. You cannot work safely if you cannot see what

you are doing.

• Report unsafe conditions or defective equipment to your immediate supervisor.

• Handle material carefully. Lift and carry properly.


nic 510 and meter labeling product requirements...nic 510 and meter labeling product requirements 23...

Documents