met hemoglobin practical hematology lab - lab 11 -

10
Met Hemoglobin Practical Hematology Lab - LAB 11 -

Upload: osborne-bryan

Post on 05-Jan-2016

226 views

Category:

Documents


6 download

TRANSCRIPT

Page 1: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Met Hemoglobin

Practical Hematology Lab

- LAB 11 -

Page 2: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Methemoglobin (Hi) is a form of hemoglobin In which the ferrous ion( Fe2+) has been oxidized to the ferric state(Fe3+) and is, therefore, incapable of reversibly combining with oxygen (and, therefore, cannot transport the oxygen molecule).

Normally, a small amount of methemoglobin is continuously being formed in the red cell, but is, in turn, reduced by the red blood cell enzyme systems:

NADH methemoglobin reductase (cytochrome-b5 reductase) (major pathway).

NADPH methemoglobin reductase (minor pathway) And to a lesser extent the ascorbic acid and glutathione enzyme

systems.

introduction

Page 3: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Clinical significanceIncreased amounts may be found in both hereditary

and acquired disorders. The hereditary form of methemoglobinemia is found in

disorders in which the red blood cell reducing systems are abnormal and unable to reduce methemoglobin back to oxyhemoglobin.

In the presence of hemoglobin M, where the structure of the polypeptide chains making up the hemoglobin molecule is abnormal (there is a tendency toward oxidation of hemoglobin, with a decreased ability to reduce it back to oxyhemoglobin).

Page 4: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Clinical SignificanceThe acquired causes of methemoglobinemia are mainly

due to certain drugs and chemicals, such as nitrates, nitrites, quinones, chlorates, sulfonamides and aniline dyes.

Normal Ranges Methemoglobin is normally present in the blood in a

concentration of 0.03 to 0.13 g/ dL, but a normal range should be determined by each laboratory. Slightly higher levels are present in infants and heavy smokers.

Page 5: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Principle Whole blood is diluted with a phosphate buffer solution. Methemoglobin has a maximum absorbance at a wavelength of

630 nm. The diluted specimen is read in a spectrophotometer at 630 nm

and the absorbance reading noted (D1). Neutralized sodium cyanide is added to the mixture, converting

the methemoglobin to cyanmethemoglobin, and read on the spectrophotometer (D2).

The change in optical density is directly proportional to the amount of methemoglobin present.

The methemoglobin in g/dL is then calculated using a factor, previously determined, for the spectrophotometer used.

Page 6: Met Hemoglobin Practical Hematology Lab - LAB 11 -

ProcedureDetermination of calculation factor, F:Before the methemoglobin results can be calculated, a

calibration factor for the spectrophotometer being used must be determined. This is done one time only, or whenever a different spectrophotometer is used for the procedure.

Obtain a whole blood sample and determine the hemoglobin concentration in g/dL.

Place 5.0 mL of 0.017 M phosphate buffer into each of two test tubes. Add 50 µL of the whole blood specimen to one tube and mix. The second tube is to be used as the blank.

Add 20 µL of freshly prepared 20% potassium ferricyanide to both tubes. Mix and allow to stand for 2 minutes.

Page 7: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Read on the spectrophotometer at 630 nm, using the blank to set the optical density at 0, and record the absorbance ( Dx).

Add 20 µL of neutralized sodium cyanide to both tubes. Mix and allow to stand for 2 minutes. Read on the spectrophotometer as above and record the optical density ( Dy).

F =Hgb (g/dL)/Dx - Dy•  

Procedure

Page 8: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Procedure for testing patient specimenLabel and place 5 mL of 0.0 17M phosphate buffer into one tube

for each specimen and control to be tested and one additional tube to serve as a blank.

Add 50 µL of whole blood to the appropriately labeled tube and mix well. Allow to sit at room temperature for 5 minutes .

Read on the spectrophotometer at a wavelength of 630 nm, using the blank to set the optical density at 0. Record the absorbance of the solution (D1)

Add 20 µL of neutralized sodium cyanide reagent to each tube including the blank, and mix. Allow to sit for 2 minutes. Read as in step c above record the optical density (D2).

Procedure

Page 9: Met Hemoglobin Practical Hematology Lab - LAB 11 -

Calculation of results Met hemoglobin (g/dL) = ( D1 – D2) x F

Normal value• Met hemoglobin <2% of total hemoglobin in normal

blood, slightly higher in infants, particularly if premature.

Note The presence of a large amount of SHb will result in an

erroneously low measurement of total Hb.

Page 10: Met Hemoglobin Practical Hematology Lab - LAB 11 -