jeopardy design process sketching projectile motion simple machines safety q $100 q $200 q $300 q...
TRANSCRIPT
Jeopardy
Design Process Sketching
Projectile Motion
Simple Machines Safety
Q $100
Q $200
Q $300
Q $400
Q $500
Q $100 Q $100Q $100 Q $100
Q $200 Q $200 Q $200 Q $200
Q $300 Q $300 Q $300 Q $300
Q $400 Q $400 Q $400 Q $400
Q $500 Q $500 Q $500 Q $500
Final Jeopardy
$100 Question – Design Process
This early stage of the design process is where you figure out what issues you are trying to solve.
Categories
$100 Answer – Design Process
Categories
What is…Identify the Problem?
$200 Question – Design Process
Categories
This last step of the design process allows designers to look back on the design process and determine what they would do differently the next time.
$200 Answer – Design Process
Categories
What is…Reflection?
$300 Question – Design Process
Categories
During this step of the design process, engineers start to see if their prototypes will work for the first time.
$300 Answer – Design Process
Categories
What is…Evaluation and Test?
$400 Question – Design Process
Categories
This step of the design process follows next in the sequence below:Immersion, Identify the Problem, Develop Specifications, Conceptualize, Plan and Select Materials, ____________
$400 Answer – Design Process
Categories
What is…Produce?
$500 Question – Design Process
Categories
During this stage of the design process, designers identify functional requirements and constraints the product must meet.
$500 Answer – Design Process
Categories
What is…Develop Specifications?
$100 Question – Sketching
Categories
This view is in the lower right hand corner of a 3-view sketch.
$100 Answer – Sketching
Categories
What is…The Right Side View?
$200 Question – Sketching
Categories
This view is in the upper left hand corner of a 3-view sketch.
$200 Answer – Sketching
Categories
What is…The Top View?
$300 Question – Sketching
Categories
This view of an object does the best job illustrating the true shape of the object.
$300 Answer – Sketching
Categories
What is…The Front View?
$400 Question – Sketching
Although they have different purposes, these two different types of lines are shown as dashed lines in a 3-view sketch.
Categories
$400 Answer – Sketching
Categories
What are…Projection and Hidden Lines?
$500 Question – Sketching
Categories
Unlike the 3-view sketches we worked on in class, this type of drawing shows a 3-dimensional view of an object.
$500 Answer – Sketching
Categories
What is…Isometric?
$100 Question – Projectile Motion
Categories
This force pulls all objects toward the center of the earth.
$100 Answer – Projectile Motion
Categories
What is…Gravity?
$200 Question – Projectile Motion
Categories
The motion of this type of object is only influenced by gravity.
$200 Answer – Projectile Motion
Categories
What is…A Projectile?
$300 Question – Projectile Motion
Categories
Dropped from the same height, two objects of different weights will hit the ground at ________ time (ignoring air resistance).
$300 Answer – Projectile Motion
Categories
What is…The Same
$400 Question – Projectile Motion
Categories
Expressed in feet per second, squared, what is the value of the acceleration due to gravity?
$400 Answer – Projectile Motion
Categories
What is…32 feet per second squared?
$500 Question – Projectile Motion
Categories
A projectile is fired at an initial velocity of 10 ft/sec and a firing angle of 30 degrees. If we keep the initial velocity the same for a second shot, this angle, larger than 30 degrees, could also be used to achieve the same range.
$500 Answer – Projectile Motion
Categories
What is…60 degrees?
$100 Question – Simple Machines
Categories
In this type of gear system, the gears turn in opposite directions.
$100 Answer – Simple Machines
Categories
What is…A Spur Gear System?
$200 Question – Simple Machines
Categories
Used to pry up objects, a crowbar is this type of simple machine.
$200 Answer – Simple Machines
Categories
What is…A Lever?
$300 Question – Simple Machines
Categories
Used to describe a twisting force, this is what you want to maximize in your mousetrap car to be able to pull as much weight as possible.
$300 Answer – Simple Machines
Categories
What is…Torque?
$400 Question – Simple Machines
Categories
Using a single moveable pulley with a rope running through it, you would have to pull on the rope with this much force to lift a 300 pound object attached to the other end.
$400 Answer – Simple Machines
What is…150 Pounds?
Categories
$500 Question – Simple Machines
Categories
In any simple machine where the input force travels farther than the output force, the output force will be _______ than the input force.
$500 Answer – Simple Machines
What is…Greater?
Categories
$100 Question – Safety
Categories
When working with tools and machines, this item of safety gear is critical for protecting your eyesight.
$100 Answer – Safety
Categories
What are…Safety Glasses?
$200 Question – Safety
Categories
This tool, used to remove small amounts of material and achieve the final shape of an object, should never be used without its handle.
$200 Answer – Safety
Categories
What is…A File?
$300 Question – Safety
Categories
During drill press operation, the material being drilled should extend ________ of the table.
$300 Answer – Safety
Categories
What is…To the Left?
$400 Question – Safety
Categories
Although used to remove drill bits from a drill press, this tool is not typically used to remove drill bits from a hand drill.
$400 Answer – Safety
Categories
What is…a Chuck Key?
$500 Question – Safety
Categories
Cutting a radius on the band saw tighter than this can cause breakage of the blade.
$500 Answer – Safety
Categories
What is…4 Times the Width of the Blade?
Final Jeopardy
Categories
Although all of the steps have a purpose and are significant, name 5 steps of the design process, in order, that had the most impact on your designs this semester.
Final Jeopardy AnswerWhat are…ImmersionIdentify the ProblemDevelop SpecificationsConceptualizePlan and Select MaterialsProduceEvaluate and TestModifyReflect
Categories