hilton_backwall-kiosk

P.O. Box 110527 Durham, NC 27709 • 4018 Patriot Dr. Ste. 100, Durham, NC 27703tel 919.544.6504 • fax 919.544.6729 • [email protected] • www.godfreygroup.com

EliteMarketing-HiltonV7_58069_INS-CustLamKiosk_6-15

Setup InstructionsSetup InstructionsElite Marketing Group-Hilton V7_58069

Custom Laminate Backwall-Counter Kiosk Assembly

EliteMarketing-HiltonV7_58069_INS-CustLamKiosk_6-15Elite Marketing Group-Hilton V7_58069

Custom Laminate Backwall-Counter Kiosk Assembly_Details


Backlit HeaderAssembly

Minka LaveryBrushed NickelWall SconceFlat-ScreenMonitor

Flat-Shelf Units

Backlit FramedGraphic

LeftFront Desk

Left BackwallCabinet

Left BackwallCabinet

RightFront Desk

RightFront Desk

Lower RightBackwall Cabinet

Upper RightBackwall Cabinet

Backlit Header

BacklitHeader

Backlit FramedGraphic

Wall Sconce

Image Front View Image Rear View

Order of Assembly1. Assemble the Backwall Cabinets by attaching the

Upper Backwall to the Lower Backwall.2. Attach the Side Left Backwall Cabinet to the

adjacent Backwall.3. Attach the Left Front Desk to the Backwall. Then

attach the Right Front Desk to the Backwall and Left Front Desk.

4. Attach the Backlit Header to the top of the Backwall.

5. Attach the Flat-Screen Monitor, Floating Shelves and Sconce Wall Light Fixtures to the Backwall Modules. Install the Framed Graphic Panels on the Left and Front side of the Counter Kiosk Assembly.

6. Once the Power Cords are cabled down to the Floor, attach the Light Fixture Sheet to the Upper Backwall backside. Attach the Light Bar Fixtures to the Fixture Sheet at the clips. Cable the cords to the terminal strips on the Backwall base.

5. Attach the Large Framed Backlit Graphic to the Upper Backwall backside as shown above.

Elite-HiltonV7_INS-CustLamKiosk_Step1_6-15Elite Marketing Group-Hilton V7_58069

Custom Laminate Backwall-Counter Kiosk Assembly_Step 1-Backwall Attachment


Lower Rt.BackwallCabinet

Lower Rt. Backwall Cabinet_Front View

Lower Rt. Backwall Cabinet_Back View

Rt. Upper Backwall Cabinet_Back View

Upper Rt.BackwallCabinet

Isometric Rear ViewAssemblyDetail Framing in the Illustration Models are not shown for clarity. Images of the components are shown as they were produced.1. Position the Lower Right Backwall at the desired

location. Note that the Cabinet Doors face the back side.2. Place the Upper Right Backwall onto the Lower Right

Backwall and secure at 12 places using the 1-3/4" pan-head bolt and washer fasteners detailed at right. Note that there are threaded inserts in the top framing plate of the Lower Backwall Cabinet.

Fastener DetailSecure Upper and Lower Right Backwall Cabinets together at 12 places using 1/4-20x 1-3/4" Pan- Hd. Bolt and Washer Fasteners.

Rt. Lower-Upper Backwall Cabinet_Front View

Flat-ScreenMonitor RemainsAttached to Wall

Backlit HeaderMounting

Location of BacklitGraphic Frame

Slot Cutouts forFloating Shelves

Left and RightFront DeskLocations


Custom Laminate Backwall-Counter Kiosk Assembly_Step 2-Lt. Backwall Attachment



LeftBackwallCabinet


Isometric Rear View

Attachment Side_Lt. Backwall Cabinet

Image Rear View_Attached to Backwall

Assembly1. Position the Left Backwall Cabinet adjacent to the Upper

and Lower Backwall as shown.2. Secure the Left Backwall Cabinet to the Backwall at 10

places using the 2" pan-head bolt and washer fasteners detailed at right. Note that there are threaded inserts in the Side Framing of the Upper and Lower Backwall Cabinets.

Fastener DetailSecure Left Backwall Cabinet to Upper and Lower Right Backwall Cabinets at 10 places using 1/4-20x 2" Pan-Hd. Bolt and Washer Fasteners.

Swing Door

FramedBacklitGraphic

AdjustableShelves onStandardHardware


Custom Laminate Backwall-Counter Kiosk Assembly_Step 3- DesksAttachment to Backwall


Image Rear View_Front Left Desk

Image Rear View_Front Right Desk Isometric Front-Right View_

Attached Desks to Backwall

Assembly1. Position the Left Front Desk against the Backwall as

shown. Secure Desk at 8 places using the 2" bolt and washer fasteners detailed below. Note that both Front Desks shipped with their Laminate Tops secured in-place.

2. Position the Right Front Desk against the Backwall and adjacent to the Left Front Desk as shown. Secure the Right Desk to the Left Desk at 2 front places using the 2-1/2" bolt and washer fasteners and 2 back places using the 2" bolt and washer fasteners detailed below.

3. Then Secure the Right Front Desk to the Backwall as shown. Secure at 4 places using the 2" bolt and washer fasteners detailed below.

Fastener DetailSecure Front Left Desk to Backwall Cabinets at 8 places using 1/4-20x 2" Pan-Hd. Bolt and Washer Fasteners.

Fastener DetailSecure Front Right Desk to Backwall Cabinets at 2 places using 1/4-20x 2-1/2" Pan-Hd. Bolt and Washer Fasteners and 2 places with the2" Pan-Hd. Bolt andWasher Fasteners.

Fastener DetailSecure Front Right Desk to Backwall Cabinets at 4 places using 1/4-20x 2" Pan-Hd. Bolt and Washer Fasteners.

2-1/2"

2-1/2" 2"

2"

2" 2"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2"

2-1/2"

2-1/2"

2"

2"

2"

2" 2"



LeftBackwallCabinet

LeftFront Desk

RightFront Desk

Laminate Tops ShipSecured to Top ofBoth Desk Frames

Place Shelf PanelInside Desk Support

Safe SecuredInside Desk


Custom Laminate Backwall-Counter Kiosk Assembly_Step 4- Backlit Header Attachment to Backwall


Isometric Front-Right View_Attached Desks to Backwall

Assembly1. Slide the Header over the top of the Backwall and with

help holding the Header Frame, secure it from the backside at 10 places using the 1-3/4" bolt and washer fasteners detailed above.

2. On the Header End Panels, secure with a 1-1/2" pan head bolt and washer from the backside thru the Upper Backwall Cabinet.

3. Note that the Backlit Header shipped intact with the Light Fixture Bars shown above installed and prewired in-series.

Refer to the attached Light Fixture Detail Sheet for additional information.

4. There are 2 Vented Sintra Panels that fit into the top groove of the Header/Backwall as shown in the illustration top right.

LeftBackwallCabinet

BacklitHeader



LeftFront Desk

RightFront Desk

Fastener DetailSecure Backlit Header Assembly to Upper Backwall Cabinet at 10 places using 1/4-20x 1-3/4" Pan-Hd. Bolt and Washer Fasteners from the backside.

Fastener DetailSecure Backlit Header Assembly to Upper Backwall Cabinet at End Panels Only using 1/4-20x 1-1/2" Pan-Hd. Bolt and Washer Fasteners from the backside at 1 place each End.

Image Front View_Upper Backwall Header BoltLocations

Image Top Back View_Backlit Header Attached to Upper Backwall

2 Vented SintraPanels Set inTop Groove

Header FrameAssembly ShipsIntact

Bolt Header to Top of Upper Backwall fromthe Backside at 10Locations


Custom Laminate Backwall-Counter Kiosk Assembly_Step 5- Accessories


A. There are 4 Framed Graphic Panels that ship intact.

B. On the 2 larger Framed Graphics, handle the longer sides in the middle to prevent the frame from deflecting and releasing the Graphic Panel.

A. There are 3 Sconce Wall Light Fixtures that need to be installed.1

Cable Hardwired Corddown grommet to TerminalStrip Below.

2

Secure Sconce Light Fixtureto Wall at 2 places with the pan-hd. fasteners provided.

3

Slide Flex Sheet into Top Ringand rest on Bottom Ring.

4

Slide Channels into Flex SheetVertical Edges as shown.

5

Slide Flex Sheet down thruBottom Ring and rest on studs.

6

Image shows Sconce Fixture located on front of Left Backwall Cabinet.

Sconce Wall Light Fixture Assembly and Attachment

All Backlit Graphic Panels areloaded in Metal Frames with 4Mounting Keyholes.

1

Place Bottom of Keyway into Shoulder BoltFastener at all 4 locations then slide Framedown to lock-in-place.

2

Shoulder Bolt Fastener

3

Align Keywayswith ShoulderBolt Fasteners

4

Backlit Opening with Light FixtureBars wired in-series.

5

Backlit Framed Graphic

6

Framed Backlit Graphic Attachment


Custom Laminate Backwall-Counter Kiosk Assembly_Step 6- Accessories


Flat-Screen with Monitor Bracket Attachment

Three Slot Cutouts for installing 3 Floating Shelf Panels. Slide notched end of Shelf Panel in slot cutout. Secure on backside with 1-3/4" pan-hd.bolt and washer fastener. Note that the Shelf Panels and their specific locations are labeled.

Backside view of Floating Shelf Panel 'A' and 'B' secured with one bolt and washer fastener each.

Monitor Wall Bracket ships attached to the face of the Backwall. Bracket is securedwith 1/4-20 x 3/4" pan-hd. bolt and washer fasteners at 4 places.

Image of Flat-Screen Monitor attached to Wall Bracket.

Flat-Screen Monitor Attachment

Floating Shelf Attachment


Custom Laminate Backwall-Counter Kiosk Assembly_Step 7- Light Fixture Sheet


Image Rear View_Exposed Backwall

Image Rear View_Light Fixture Sheet

Image Rear View_Light Fixture Sheet attached to Upper Backwall

Wood BlocksSecure FixtureClips on Front

Fixture Clips onFront Side ofFixture Sheet

4 ShoulderBolts for AttachingFramed Graphic

Velcro Stripson Fixture SheetBacksideFixture Sheet adheres

to Velcro on HorizontalWood Frames

Assembly1. Velcro the Sintra Light Fixture Sheet to the Backside Backwall Framing

as shown. The Light Fixture Clips face the backside.


Custom Laminate Backwall-Counter Kiosk Assembly_Step 8- Light Fixture/Framed Backlit Graphic


Image Rear View_Installed Backlit Framed Graphic

Image Rear View_Light Fixture Sheet with Fixture Bars Attached

Assembly1. Assemble and clip the Light Fixture Bars to the Fixture Sheet as shown.

Note the Fixture Wattages and their orientation. Wire the fixtures in-series and cable the power cord down to the Lower Backwall.

2. Assemble the Framed Graphic and hang in front on the perimeter frame. Refer to the Step 5 for Framed Graphic Panel attachment.

18w

18w

18w

18w

29w

29w

29w

29w

6w

6w

6w

6w

4 ShoulderBolts for AttachingFramed Graphic

Large FramedBacklit Graphic

Fluorescent LightFixtures Clipped toFixture Sheet

Fluorescent Light Fixture Assembly Using Jumper WiresUsing Jumper Wires

FemaleHousingEnd

MaleHousing

End

FemaleHousing

End

MaleHousing

End

FluorescentLights

JumperWire

Female HousingEnd

Power Cord

Connecting Lightsin a Series

Jumper Wire

Jumper Wire

Power Cord

1

2

3

4

Parts

List

Power Cord

FluorescentLights

JumperWire

Female/MaleAdapter

FemaleHousing

End

MaleHousing

End

Velcro onBack Side

Fluorescent Bulb AttachmentFluorescent Bulb AttachmentExteriorSlot1 2 3

Twist the Light Housing so that it lines up with the Exterior Slot

Slide the Fluorescent BulbProngs down into the LightHousings on both ends

Twist the Fluorescent Bulbeither direction until the Bulb Locks in place

Twist Until Bulb Locksin Place

LightHousing

Joining Two FixturesJoining Two Fixtures

1 2 3 Joined Fixtureson a Light Bar

Jumper

Power Cord

Female/MaleAdapter

MaleHousingEnd

FemaleHousingEnd

Attach the Female End of theAdapter to the Male Housing End

Then attach the FemaleHousing End to the

Adapter

Lights attachedtogether withFemale/Male Adapter

Metal Clips -AlternateAttachmentMethod

FluorescentLight_Update_10-13


hilton_backwall-kiosk

Documents