section 1 - pdf4pro
TRANSCRIPT
1/1
1
ELECTRICAL PARTS &
ACCESSORIES INCLUDING
HEADLIGHT & TAILLIGHT
BRACKETS, LICENSE PLATE
HOLDERS, & HORNS.
SECTION 1
ELECTRICAL
PART APPLICATION / OEM JISNO. YEARS NO. NO. ASSY
STANDARD BATTERIES1-97 FL & FLH models 1965/1984. Sportster® models 66007-84 YHD-12 12 240 28 8-1/8” 5-1/4” 6-1/2”
electric start 1967/1978, except XLCR.1-33 FX & XL models (kickstart only) 1970/1978. 66006-70 12N7-4A 12 74 7 5-5/16” 3” 5-1/4”
1-76 FX models (electric start) 1973 & later. 65991-75C YB16-B 12 240 19 6-7/8” 4” 6-1/8”
FXR models 1982 & later. Softail® models 1984/1990. Sportster® 1979/1996. XLCR 1977 & 1978.
1-67 FLT, FLHT & FLHR models 1980/1996. 66010-82 Y50-N18L-A 12 260 20 8-1/8” 3-9/16” 6-3/8”
1-98 All Softail® & Dyna® models 1991/1996. 65989-90A YB16HL-A-LM 12 255 19 6-7/8” 4” 6-1/8”
1-71 Custom 12V; use with early 6V style tanks. 12N5.5A-3B 12 60 5.5 4-1/16” 3-9/16” 4.5”
LOW MAINTENANCE BATTERYThis battery fights sulfate crystal buildup on battery plates. Helps the battery last longer. This is the OEM equivalent for thesemodel years.
1-58 Softail® 1984 thru 1990. Electric start FX & FXR, 65991-82A YB-16-B-LM 12 240 19 6-7/8” 4” 6-1/8”
1973 thru 1994. XL 1979 thru 1996.
MAINTENANCE-FREE BATTERIES1-55 All Softail® & FXD models 1997 & later. XL models 65989-97 YTX20L-BS 12 270 18 6-7/8” 3-7/16” 6-1/8”
883 & 1200 1997 & later. Buell S3, S3T Thunderboltmodels 1997 & later. Buell X1 Lightning models 1999.Buell M2 Cyclone models 1997 & later.
1-56 FX models (electric start) 1971 & later. FXD models 66672-96 YTX20-BS 12 270 18 6-7/8” 3-7/16” 6-1/8”
1991/1996 NOTE 1. All Softail® models 1984/1990.XL models 1979/1996. Buell models 1987/1996.
1-110 Custom application. This is a very small N/A YTZ14S 12 230 11 6” 3-7/16” 4-3/8”
battery; excellent for use where space orheight is an issue. See example photo above.
1-57 FLH & FLHT models 1997 & later. 66010-97A YTX30-L 12 335 30 6-9/16” 5” 6-7/8”
1-115 XL & XLH (Sportster®) models 2004 & later. 65958-04 YTX14L-BS 12 200 12 6” 3.4375” 5.75”
NOTE 1: Requires use of below battery installation kit for Dyna Glide® models 1991 thru 1996.
1/2
1 A. THUNDERVOLT® BATTERIES
Maintenance-free 12V motorcycle batteries featuring gas recombination technology. These 20 amp hour batteries have 270 coldcranking amps producing a high rate of discharge current, giving consistent starting and excellent reserve capacity. SOLD EACH
LEN
GTH
WID
TH
CO
LD C
RA
NK
AM
PS
AM
P H
OU
RS
VO
LTS
HE
IGH
T
-
+
-+
-+
- +
-+
- +
-+
- +
-+
- +
-+
This kit is necessary when installing maintenance-free batterypart No. 1-56 in Dyna Glide® models 1991 thru 1996.
78-327 Battery installation kit. SOLD AS KIT
- +
A
B
B. BATTERY INSTALLATION KIT
1-110
1/3
1A. THUNDERVOLT® AGM BATTERIES
Ultima’s AGM Thundervolt® batteries are the highest performance batteries we offer today! These are an industry first, with a direct fitaftermarket replacement for OEM# 65989-97A. These batteries provide some of the highest power ratings available in theAftermarket.
FEATURES:• Patented post design reduces internal battery resistance by
replacing 3 internal connections with 1.• Flush mount, threaded terminals allow for easy connection to
bike terminals.• Nonspillable, sealed AGM Valve Regulated Lead Acid (VRLA)
design is maintenance free and meets all requirements for shipment via air carrier.
• Rugged construction has been lab tested and field tested to ensure long life, even in demanding V-Twin applications.
• Higher AH capacity than OEM means more starting capacity before wearing battery down, particulararly useful for those stubborn steeds.
• Manufactured by an ISO 9001:2000 registered factory• Patented Cast-On-Stip (COS) manufacturing technology ensures
consistent long battery life.
Ultima OEM Part No. Part No. Applications1-140 65989-97B Softail 1997/later, XL 1997/2003, Dyna 1997/later, VROD (except VRSCR) 2007/later1-142 66010-97B FLH, FLT 1997/later★1-143 65958-04 XL models 2004★1-144 65989-90B Dyna & Softail models 1991/1996★1-145 65991-82B Electric start FX and FXR 1973/1994; XLCR 1977/1978, XL models 1979/1996; Softail models 1984/1990;
FXR models 1999/2000★1-146 66010-82B FLHR, FLHT, and FLT Touring models 1980/1996★1-141 66007-84 FL & FLH models 1965/1984. Sportster® models electric start 1967/1978, except XLCR.★1-147 65948-00 VRSC models 2002/2006, VRSCR 2007★1-148 66006-70 FX & XL models (kickstart only) 1970/1978.
★1-150 V-Twin Terminals. Replacement terminals & screw for above battery. Except 1-148 & 1-141.
1-140
A
C
D. BATTERY TENDER TWIN 800The BT-TWIN housing is a very close replica of the popular V-Twinmotorcycle engine configuration. An internal sound chip mimics thesound of a motorcycle engine starting when you connect the charger toa battery. For your convenience, there is also a button to let you acti-vate the sound at any time.
This charger has 2 separate 12 volt outputs with 800 millamps of pureconstant current charging power. Coupled with a brain (IC chip), thecharger will constantly monitor, charge, and then maintain your bat-tery.
• "Supersmart" Technology
• Spark Proof
• Short Circuit Protected
• Reverse Polarity Protected
• Dual Output
• Weighs only 2 Pounds
• 3 Year Warranty
1-108 Battery Tender Twin 800, 12 volts @ 800 mA SOLD EACH
1/4
1
B. ULTIMA BATTERY CHARGER“Trickle charge” battery charging system. Comes complete with twopigtails and 2 alligator clips.
1-121 Ultima Battery Charger SOLD EACH
A
D
C. EZ CHARGERNew generation fail-safe automatic battery charger. New technologykeeps the battery at full charge all winter long. Worry free. Just plug in.Won’t cook your battery. Perfect for charging and holding full chargeon batteries for motorcycles as well as automobiles, snowmobiles, jetskis and stand-by generators.
The EZ Charger is not just another “trickle charger.” The EZ Charger isa solid state, automatic battery charger that is designed to charge 12Vlead acid batteries to full charge and then to retain that full charge(unattended) for extended storage periods.
1-102 EZ Charger; has two pigtails — one with alligator SOLD EACH
clips and another with rings.1-101 EZ Charger; has pigtail with rings.
1-102
1-101
B
For the economy conscious, we offer these batteries — quality at the right price.
A. BATTERIES - COMPETITIVE PRICED
-+
-
+
-+
- +
- +
PART AMPNO. JIS NO. VOLT HOURS LENGTH WIDTH HEIGHT ASSEMBLY
1-4 12N7-4A 12 7 5-3⁄8” 3” 5-1⁄4”
1-6 Y50-N18L-A 12 20 8-1⁄8” 3-9⁄16” 6-7⁄16”
1-5 12N5.5A-3B 12 5.5 4-1⁄16” 3-9⁄16” 4-1⁄2”
1-2 YB16-B 12 19 6-15⁄16” 4” 6-1⁄8”
1-3 YHD-12 12 32 8-1⁄8” 5-1⁄4” 6-1⁄2”
SOLD EACH
1/5
1A. BATTERY TENDERBattery Tender Plus is a 1.25 amp battery charger without the damag-ing effects of a trickle charger. Includes quick-connect harness forhard-to-reach areas. Requires 115 VAC.
1-105 Battery Tender Plus; 12V @ 1.25A. SOLD EACH
Battery Tender Junior is perfect for all lead acid, sealed maintenancefree and gel cell batteries. Includes quick-connect harness for hard-to-reach areas. Requires 115 VAC.
1-104 Battery Tender Junior; 12V @ 750 mA. SOLD EACH
B. YUASA AUTOMATIC BATTERY CHARGER900mA Charger — most powerful available for this size charger. Peaksat 14.4V and then goes to float mode. Perfect for maintaining ourThunder Volt sealed batteries. 3-Light display tells you the charger sta-tus at a glance.Fully automatic with reverse polarity protection — mistake proof. Willnever overcharge your battery! Includes alligator clip and quick con-nect harness. This baby has it all!
1-107 Yuasa 900mA automatic charger. SOLD EACHB
A
Fits 1985 & later Softail® oil tanks. Molded rubber. Will work on allyears Softail®.
78-322 Battery cushion. OEM 66210-85B and SOLD EACH
OEM 66210-97.
Cushion kit is ideal for battery boxes & custom oil tanks. Pure neo-prene closed cell foam rubber is non-absorbent & comes with adhe-sive backing. This cushion keeps vibration, the main cause of crackedbatteries, to a minimum.
78-173 5” x 8” For FLH 1965 thru 1984 or cut SOLD EACH
to size.78-217 4” x 6-1⁄2” For FXE 1973 thru 1984.
D. BATTERY COMPARTMENT CUSHION KITS
BLACKNEOPRENE FOAM
E. BATTERY CUSHION FOR SOFTAIL®
F
C
Complete support bracket with grommet.
14-25 For XLH 1967 thru 1978. Replaces SOLD EACH
OEM 66480-67 and OEM 11422.CHROMEPLATED
14-26 Fits FXE 1973 thru 1984. SOLD EACH
OEM 66225-73.
CHROMEPLATED
G. BATTERY SUPPORT BRACKET FOR XLH
F. BATTERY CARRIER & STARTER MOTORBRACKET FOR FXE
D
E
The answer to starting that bike with a dead battery & no kick starter.This set of heavy duty cables measures over 5 feet long and is still com-pact enough to carry with you.
97-5 Jumper cables. SOLD EACH
C. MOTORCYCLE JUMPER CABLE
1-105
1-104
G
1/6
1
D. BATTERY CARRIER TRAYSReplacement battery carrier complete with battery pad, rubber mount-ing studs, brackets. Hardware included with kits except for part No. 14-23.
14-20 Fits FL 1974 thru 1979. OEM 66204-74. SOLD AS KIT
14-21 Fits FXE 1973 thru 1983. OEM 66191-73.14-23 Fits XLH 1967 thru 1977. OEM 66205-75. No hard-
ware included.
14-23
ALLPARTS
CHROMEPLATED
14-20
14-21
For H-D® Big Twin 1937 thru 1964. All parts chrome plated.
89-3 Battery cover. OEM 66373-36. SOLD EACH
5-72 Plate & fender bracket. SOLD EACH
OEM 62585-36.89-36 Battery/oil tank plate. OEM 62575-36. SOLD EACH
5-70 Battery rods. OEM 66390-36. SOLD AS PAIR
14-30 Battery support bracket. SOLD EACH
OEM 62584-58. Paughco.14-31 Bracket spacers. OEM 62581-36. SOLD AS PAIR
Paughco.
C. BATTERY PLATES, PADS, RODS & BRACKETS
89-3ALL PARTS
CHROMEPLATED
89-36
5-72
5-70
14-30
14-31
C
D
A. BATTERY TRAY MOUNT
CHROMEPLATED
Chrome plated battery tray mount.
14-28 Fits FLH 1965 thru 1986. Replaces SOLD EACH
OEM 66212-65.
Protects chrome and paint from battery acid discharged from the venttube. Easy to install on any model. Several types to choose from.Economical plastic catch tank with tie wraps for mounting and venttube. Also custom billet in natural, black or chrome; includes plasticcatch tank and mount bracket.
1-15 Battery acid catch tank. SOLD EACH
B. BATTERY ACID CATCH TANKS
A
B
1/7
E. BATTERY TOP COVERS
D. WRAP AROUND BATTERY COVERS
89-120
89-11989-181CHROME PLATED
HEAVY GAUGE STEEL
89-120 For FL and FLH. OEM 66370-65. SOLD EACH
89-119 For FXE, FXS, FXEF & Low Rider®, also 883cc1100cc & 1200cc Evolution®. OEM 66367-73.
89-181 All FX & Sportster® 1970 thru early 1978. Kickstart only. OEM 66369-70.
89-230 For XLH 1967 thru 1978. OEM 66369-67.
89-35 For electric start Super Glide® 1973 SOLD EACH
thru 1986 except FXR & FXRS, also Sportster® 1982 thru2003. Plain.
89-88 Fits FL, FLH, FLH-80, Classic, 1970 & later.OEM 66378-70. Plain.
89-255 Same application as above part No. 89-88except ribbed. OEM 66378-70.
89-22 For BSA/Triumph, Sportster® XLCH (kickstart)1970 thru 1978, and Super Glide® kickstart. Plain.
89-143 For Sportster® 1980 & 1981. Plain.89-231 For early XLH, and Sportster® electric start,
1967 thru 1978. OEM 66379-67. Plain.89-256 Same application as above part No. 89-231 except ribbed.
89-230
CHROMEPLATED
RIBBED
B. BATTERY COVER FOR DYNA®Wrap-around top / side cover with black painted accent at bottom.
89-500 For Dyna® 1991 & later. Replaces SOLD EACH
OEM 66192-99.
CHROMEPLATED
C. BATTERY COVER FOR FXD89-501 For FXD 1997 & later. SOLD EACH
Replaces OEM 66375-99.
CHROMEPLATED
Top, bottom, and strap to hold FXE style battery for use with our partNo. 26-126 oil tank in rigid Sportster® frames.
14-29 Battery box kit. SOLD AS KIT
A. BATTERY BOX KIT FOR RIGID FRAME SPORTSTER®
A
B
C
D
E
1
1/8
1
B. ULTIMA INDIVIDUAL CABLES — SOLD EACH
END LUG SIZES 8” 9” 10” 11” 12” 13” 14” 15” 16” 17” 30” 33”
1/4” and SMOKE 18-713 18-714 18-715 18-716 18-717 18-718 18-719 18-720 18-721 18-722 18-723 18-724
5/16” lugs CLEAR 18-743 18-744 18-745 18-746 18-747 18-748 18-749 18-750 18-751 18-752 18-753 18-754
1/4” and SMOKE 18-725 18-726 18-727
3/8” lugs CLEAR 18-755 18-756 18-757
5/16” and SMOKE 18-728 18-729 18-730
3/8” lugs CLEAR 18-758 18-759 18-760
ULTIMA PREMIUM BATTERY CABLES
Check out our new line of premium battery cables!
Available in clear braid & clear smoked.
• Super flexible multi-stranded therefore not affected by V-twin vibration.
• Pure oxygen free copper stranding individually tinned preventing corrosion.
• Heavy duty copper lugs silver plated for long lasting trouble free connections.
• Minimum voltage drop for sure starting.
A. ULTIMA CABLE SETSBATTERY TO
SMOKE CLEAR GROUND SOLENOID / SOLENOIDPART NO. PART NO. YEAR LENGTH STARTER TO STARTER
ALL FLH & FLT DRESSER MODELS
18-701 18-731 1965 / 1979 9” 16” 16”
18-702 18-732 1980 / 1988 9” 30” 30”
18-703 18-733 1989 / 1992 33” 33” —
18-704 18-734 1993 -LATER 13” 14” —
ALL FXST & FLST SOFTAIL®
18-705 18-735 1984 / 1988 8” 17” 15”
18-706 18-736 1989 / 2001 10” 12” —
18-707 18-737 1989 - LATER 10” 14” X-LONG —
ALL FXR LOW RIDER®
18-708 18-738 1982 / 1988 12” 16” 16”
18-709 18-739 1989 - LATER 12” 16” —
ALL FXD DYNA®
18-710 18-740 1991 / 2002 10” 15” —
18-711 18-741 2003 - LATER 15” 16” —
ALL SPORTSTER®
18-712 18-742 1981 - LATER 11” 16” —
GET THE MOST FROM YOUR
STARTER AND BATTERY WITH
ULTIMA CABLES
C. SHOP PAKSIncludes 1 of each cable above.18-199 Clear SOLD AS PKG.
18-198 Smoke
CLEAR SMOKE
1/9
1Part No. 5-129 & 5-220 are made of black rubber. The other straps aremanufactured to meet or exceed H-D® specifications from 18 gaugestainless steel with plated eye bolts to prevent rust.
5-30 1967 Thru 1978 XLH & Sportster®. OEM 66470-67.SOLD EACH
5-31 1970 And later FLH, FL & H-D® 74”. OEM 66383-70.5-32 1970 And later XLCH & FX. OEM 66470-70.5-33 1973 And later all FX, electric start and 883cc,
1100cc & 1200cc Evolution®. OEM 66476-73.5-129* 1984/1991 FXST & FLT and 1979 Sportster®.
OEM 66105-77.5-220* 1992/1999 Softail®. 2 Piece. OEM 66109-93
& 66111-93.
*Part No. 5-129 & 5-220 are interchangeable.
A. BATTERY STRAPS
5-129 5-30
5-31
Sumax’ Heavy Duty cables are a very flexible 8 gauge 50amp ratedcopper core, PVC insulation, SGT jacket with crimped insulated ringterminals (1/4” & 5/16” eyelets). These are an excellent replacementcable at a very affordable price for all stock H-D® motorcycles. 100%U.S.A. MADE
Dealer assortment 10-pack. Comes with 4 of 8-1⁄2” cables, 3 of 11”cables, 2 of 15” cables, and 1 of the 8-1⁄2” braided ground cable.
18-180 SOLD AS PKG. OF 10
8-1⁄2” Cable with 5⁄16” & 3⁄8” eyelets. Used as battery ground strap onFL 1965 & later, FXE 1973 & later, and XL 1981 & later.
18-177 Replaces OEM 70209-65A, SOLD AS PKG.OF 6
70461-67, and 70011-81.
11” Cable with 5⁄16” & 3⁄8” eyelets. Used as a positive battery cable onXL & XLS late 1975 & later, and negative cable on XL & XLS 1979 &later, also solenoid to starter cable on FLT 1980 & later.
18-178 Replaces OEM 70097-75 & 70100-70. SOLD AS PKG. OF 6
15-1⁄2” Cable with 5⁄16” & 3⁄8” eyelets. Used as positive battery cableon XLH 1967 thru early 1975, XL 1982 & later, also battery to solenoid &solenoid to starter cables on FL 1965 & later and FX series 1973 & later.
18-179 Replaces OEM 70069-65A & 70083-82. SOLD AS PKG. OF 6
11-3⁄4” Cable. Used as positive battery cable on FXST models.
18-257 Replaces OEM 70078-91. SOLD AS PKG. OF 6
Heavy duty kits for late models.
18-470 For Softail® 1989 thru 2003; 10” & 12”.18-471 For Dyna® 1991 thru 2003; 10” & 15”.18-472 For FXR 1989 thru 2003; 12” & 16”. SOLD AS KIT
18-473 For FLT® 1992 thru 2003; 13” & 14”.18-474 For XL 1981 thru 2003; 11” & 16”.
B. SUMAX BATTERY CABLES
5-220
Sumax’ Extreme Duty cables are a very flexible 2 gauge 180amprated copper core, with closed barrel style terminals (1/4” & 1/16”eyelets) made of tinned copper insulated by black heat shrinksleeves. These very fat and very flexible cables will transfer morecranking power with less voltage drop than any other cable onthe market. They are designed to work with all your big horse-power motors on the market today. 100% Made in the U.S.A.
18-475 For Softail® 1989 thru 2004; SOLD AS KIT
10” & 12”.18-476 For Dyna® 1991 thru 2004; 10” & 15”.18-477 For FXR 1989 thru 1994; 12” & 16”.18-478 For FLT® 1993 thru 2004; 13” & 14”.18-479 For XL 1981 thru 2003; 11” & 16”.
HEAVY DUTY
A
B
1/10
1
INDIVIDUAL CABLES — SOLD EACH
END LUG SIZES 12” 16”
1/4” and 5/16” lugs 18-395 18-399
POSITIVE BATTERY CABLES18-106 Battery positive terminal cable for Super Glide®, all models SOLD EACH
1971 thru 1981. Measures center to center 16-3⁄4”. Cable end holesare 3⁄8” & 5⁄16”. OEM 70069-65A.
18-107 Battery positive terminal cable for Sportster® 1975 thru 1977. Measurescenter to center 13”. Cable end holes are 3⁄8” & 5⁄16”. OEM 70097-75.
NEGATIVE BATTERY GROUND STRAP/CABLE18-109 Ground strap for electric start Sportster® 1968 thru 1977. SOLD EACH
Measures center to center 9-1⁄8”. Strap end holes on both endsare 5⁄16”. OEM 70235-67.
18-108 Ground cable for FL & FLH, 1965 thru 1978. Measures center to center9-1⁄4”. Cable end holes are 3⁄8” & 5⁄16”. OEM 70209-65.
18-106
18-109
B. ELECTRIC CABLES
A. MEGA•CABLES FOR STARTERS WITH HIGH TORQUE
Got big compression?! Starter drags?! Maybe it’s not the starter or thebattery.
Many times inferior cables are the problem. Check these out!
✧ Less voltage drop.
✧ Gold plated heavy copper terminals
✧ Super-flexible silicone jacketed.
✧ 1,665 Strands of tinned copper wire.
✧ Extends life of battery and starter on stock applications.
CABLE SETSBATTERY TO
PART GROUND SOLENOID / SOLENOIDNO. YEAR LENGTH STARTER TO STARTER
ALL FLH & FLT DRESSER MODELS
18-381 1965 / 1979 9” 16” 16”
18-382 1980 / 1988 9” 30” 30”
18-383 1989 / 1992 33” 33” —
18-384 1993 / 2001 13” 14” —
ALL FXST & FLST SOFTAIL®
18-385 1984 / 1988 8” 17” 15”
ALL FXR LOW RIDER®
18-387 1982 / 1988 12” 16” 16”
18-388 1989 / 1994 12” 16” —
ALL FXD DYNA®
18-389 1991 / 2001 10” 15” —
GET THE MOST FROM YOUR
STARTER AND BATTERY WITH
MEGA●CABLES
A
B
1/11
1
B. WEDGE MOUNT LED BULBSStock style wedge mount bulbs for late 2003 applications.
6-68 3156 Wedge mount single element. SOLD EACH
6-69 3157 Wedge mount dual element.
Custom wedge mount bulbs. SOLD EACH
6-112 Wedge mount single element Amber.6-113 Wedge mount dual element Red.6-114 Wedge mount dual element Amber.
6-114
A. L.E.D. BULBS
RED AMBERDESCRIPTION LEDS LEDS
Angled, single contact 6-5 6-9
Angled, dual contact 6-6 6-10
Straight, single contact 6-3 6-7
Straight, dual contact 6-4 6-8
SOLD EACH
STRAIGHT
ANGLED
Water and vibration proof. Will last up to 100,000 hours. 31 LEDs perbulb. 1-5/8” O.D.
NOTE: Dual contact = 1157, single contact = 1156.
D. REPLACEMENT LED BULBThis 1157 replacement bulb has 18 Red LED’s facing out and 6 WhiteLED’s to illuminate license plate.
6-117 1157 LED; replacement for dual SOLD EACH
filament bulb for taillight / license.
“Mega Bright” halogen taillamp could help keep you from getting runover. 15 Watt taillight is 800% brighter than standard bulbs, and stoplight is 50 watts — 3 times brighter than stock. One of the best safetyitems you can buy!
6-64 “Mega Bright” halogen bulb. Fits SOLD EACH
right into the stock bulb base.
E. MEGA BRIGHT TAILLAMP BULB
Sight not that crisp on night rides? Advances in technology allow a 30to 40% increase in perceived light. While replacing the standard H-412V 60/55w bulb, the XB3 xenon boosted bulb uses a new coatingmaterial that actually increases the color temperature of the bulb tomove the light closer to daylight. Xenon gas is used to cool the fila-ment and allow the halogen process to produce a higher light output.The special blue coating increases the whiteness of the light with onlya trace of blue at the headlight periphery. Don’t confuse these with theblue coated bulbs currently being marketed.
6-63 XB3 Xenon bulb. No wiring SOLD EACH
modifications or special installation required.
C. XB3 XENON BOOSTED HEADLAMP BULB
F. H-4 XENON BULBSXenon gas is used to cool the filament and allow the halogenprocess to produce a higher light output. No wiring modificationsor special installation required.
6-65 60/55W bulb. SOLD EACH
6-66 100/90W bulb.6-67 130/90W bulb.
A
B
C
D
E
F
6-68
1/12
1
ALL BULBSSOLD EACH
BULBSNOT SHOWN
TO SCALE
18.5
35C
E
25.5
45
25.5
45
21.5
12
A
B
D
F
STOCK BULBSAMERICAN6-11 A4813/1154 B 6V 18⁄3W Taillight. H-D® No. 68165-476-54 A62 D 6V 3W Instrument light - H-D® No. 68462-49
Hi-Lo.6-55 A72 D 12V 3W Instrument light - H-D® No. 68462-64
Hi-Lo.6-40 1156 A 12V Turn signal. H-D® No. 68572-64A6-43 GE1034 / 1157 B 12V 18⁄6W All taillights. H-D® No. 68165-64
ENGLISH6-11 A4813 B 6V 18⁄3W Taillight. 6V models.6-43 GE1034 / 1157 B 12V 18⁄6W Taillight. 12V models.
HONDA6-11 A4813 B 6V 18⁄3W Taillight. 6V models.6-43 GE1034 / 1157 B 12V 18⁄6W Taillight. 12V models.
KAWASAKI6-11 A4813 B 6V 18⁄3W Taillight. 6V models.6-43 GE1034 / 1157 B 12V 18⁄6W Taillight. 12V models.
SUZUKI6-11 A4813 B 6V 18⁄3W Taillight. 6V models.6-43 GE1034 / 1157 B 12V 18⁄6W Taillight. 12V models.
YAMAHA6-11 A4813 B 6V 18⁄3W Taillight. 6V models.6-43 GE1034 / 1157 B 12V 18/6W Taillight. 12V models.
SEALED BEAM UNITSPART MFG.NO. NO. REF. VOLTAGE APPLICATION MODELS
7-42 GE6006 H 6V 30/30W H-D® No. 67717-48. 7” Dia. sealed beam.7-47 GE6012 H 12V 60/50W H-D® No. 67717-64 and all Japanese with
7” dia. sealed beam.7-39 GE4020/ I 6V 30/30W H-D® No. 67717-59.
TS40677-25 GE4420/ I 12V 30/30W H-D® No. 67717-65. Late Sportster®.
TS4467 M.W. part No. 8-16 lights.7-52 H 5006 N/A 12V 50/35W H-D® No. 67698-81B. 12V Halogen “Motorcycle”
sealed beam. 5-3⁄4” Dia.7-26 H 5006 35/35W H-D® No. 67698-81B. 5-3⁄4” Dia. quartz halogen.
CUSTOM BULBS6-11 A4813 B 6V 18/3W All taillights.6-43 GE 1034 B 12V 18/6W All taillights.6-56 A1272 E 12V 2W VDO instruments.6-48 H-3 F 12V 55W Quartz iodide.6-32 H-4 G 6V 60/55W Quartz iodide. M.W. part No. 7-45 & 7-46 lights.6-52 H-4 G 12V 60/55W Quartz iodide. M.W. part No. 7-45 & 7-46 lights.6-61 H-4 G 12V 100/55W Quartz iodide. M.W. part No. 7-45 & 7-46 lights.6-57 A4125 C 12V 15W King marker. M.W. part No. 8-80 lights.6-55 A7113 D 12V 3W Queen marker. M.W. part No. 8-82 & 8-83 lights.6-14 MR16 Spot 20W Beacon-2 Halogen marker lights.6-15 MR16 Spot 35W Beacon-2 Halogen marker lights.
G
7.031"MAX.
5"MOL
5.700"MAX.
4"MOL
H
I
1/13
1
CHROMEPLATED
5-1⁄2” Triple chrome plated 12V headlamp with bottom mount and highbeam indicator light.
8-142 Headlamp with sealed beam. SOLD EACH
7-54 Replacement 12V sealed beam.
D. 5-1⁄2” CUSTOM SEALED BEAM HEADLAMPD
B. INDICATOR LAMPSThese 3/8” diameter one-piece indicator lights are perfect for customor stock applications. They’re used on many 1984 thru 1993 models. 6”Long leads with wiring pins.
8-157 Red. Replaces OEM 68489-86. SOLD EACH
8-158 Amber. Replaces OEM 67864-86.8-159 Green. Replaces OEM 68574-86.8-160 Blue. Replaces OEM 67862-86.8-161 Replacement clip. OEM 68608-83.18-39 Replacement wiring terminal pin. OEM 72039-71.
The Xe7 Xenon bi-function HID headlamp module provides an extraor-dinary upgrade for motorcycles equipped with 7” round incandescentor halogen headlamps. The classic chrome bezel (front surface area)styling provides a very unique look — clean, distinct & noticeable. TheXe7 headlamp kit comes with everything you need to add performance& style to your motorcycle. In some cases, modification to the lightbucket may be required to accommodate the Xe7 housing.
HID (High intensity discharge) headlights are the brightest lightsavailable.3000 Hour life expectancy.Draws only 35 watts.The 3” o.d. projector lens is shatterproof
and passes DOT requirements.Dressers will require headlight bucket modification.Complete instructions included.
8-313 7” Round headlamp. SOLD EACH
C. XSIGHTING LIGHTING Xe7 HEADLAMP
A. LED BULBSPART NO. OFNO. PIECES COLOR FILAMENT REPLACES
6-101 19 Red Dual 1157
6-102 19 Amber Dual 1157
6-103 19 Red Single 1156
6-104 19 Amber Single 1156
SOLD EACH
6-101,6-102
19 PIECE
A
B
C
1/14
1 A. CUSTOM HALOGEN HEADLAMPS & SPOTLAMPS
These headlamps are designed with a new diamond cut reflective sys-tem that concentrates the beam on the road. Designed as a directreplacement for most headlamps. DOT approved for use with 55/60watt, 12V H-4 bulb (included).
7” DIAMETERDOT approved for use with 55/60 watt, 12V H-4 bulb (included).
6-52 Replacement H-4, 55/60, 12V bulb. SOLD EACH
5-3/4” DIAMETER7-58 Ice; clear lens with bulb cover.SOLD EACH
6-52 Replacement H-4, 55/60, 12V bulb.
4-1/2” DIAMETER MATCHING SPOTLAMPSDOT approved. Comes with H3 55 watt bulb.
7-66 Trillient style halogen passing lamp. SOLD AS PAIR
7-67 Bullet style halogen passing lamp. SOLD AS PAIR
6-48 Replacement H-3, 55W, 12V bulb. SOLD EACH
ICE
TRILLIENT
BULLET
A
B. REPLACEMENT HEADLAMPSReplacement headlamps, H4 55/60W bulb included, available with orwithout tri bar.
4-1/2” DIAMETER★8-436 Lamp unit, tri bar. SOLD EACH
★8-437 Lamp unit, plain.
5-3/4” DIAMETER★8-438 Lamp unit, tri bar. SOLD EACH
★8-439 Lamp unit, plain.
B
Light it up with these all new Ultima L.E.D. headlamps. We have com-bined an L.E.D. “halo” with a halogen bulb wired seperately so as notto interfere with everyday highway usage. Just flip the switch at thenext parade or bike show & you have instant crowd gathering illumina-tion. L.E.D. colors available in Red, White, Blue or Amber. 5-3/4 diame-ters, H4 55/60 W. DOT approved. SOLD EACH
5-3/4" HEADLAMPS (LAMP ONLY) W/TRI-BAR★8-440 Ultima L.E.D. headlamp, red.★8-441 Ultima L.E.D. headlamp, clear/white.★8-442 Ultima L.E.D. headlamp, blue.★8-443 Ultima L.E.D. headlamp, amber.
C. ULTIMA HALO L.E.D. REPLACEMENTHEADLAMP
C
TRI BAR
1/15
1Our chromed aluminum spun headlights are a great choice for yourbike. They come with or w/o a visor, with tri-bar, H4 55/60 W bulb andare available in several styles and sizes. SOLD EACH
4-1/2” DIA. • 6-3/4” LENGTH8-20 Headlight w/round visor, tri bar.
★8-40 Headlight w/round visor, plain.8-331 Headlight w/point visor, tri bar.
★8-431 Headlight w/point visor, plain.8-332 Headlight no visor, tri bar.
★8-432 Headlight no visor, plain.
5-3/4” DIA. • 9-1/2” LENGTH (LONG BODY)8-21 Headlight w/round visor, tri bar.
★8-41 Headlight w/round visor, plain.8-327 Headlight w/o visor, tri bar.
★8-427 Headlight w/o visor, plain.8-333 Headlight w/pointed visor, tri bar.
★8-433 Headlight w/pointed visor, plain.
5-3/4” DIA. • 8-1/2” LENGTH (SHORT BODY)8-335 Headlight w/o visor, tri bar.
★8-435 Headlight w/o visor, plain.8-334 Headlight w/visor, tri bar.
★8-434 Headlight w/visor, plain.
5-3/4” DIA. • 6-3/4” LENGTH (CUSTOM TYPE)8-251 Headlight w/o visor.8-252 Headlight w/visor.
7” DIA. • 8-1/2” LENGTH (SHORT BODY)★8-477 Headlight w/visor, tri bar.★8-478 Headlight w/visor, plain.
A. CHROMED ALUMINUM HEADLIGHTSWITH OR WITHOUT TRI BAR
8-20
8-21
8-331
8-332
8-327
8-333
8-251
8-335
8-334
8-252
1/16
1A
8-336
8-337
8-338
8-339
8-340
Chromed aluminum projection headlights are 4-1/2” in dia., 8” long,
H1-75 W, Single Beam (Hi or Low). SOLD EACH
8-336 Projection bullet style headlight, w/o visor.
A. PROJECTION BULLET STYLEHEADLIGHTS
Chromed aluminum eyeball type headlights are w/ tri-bar, 5-3/4” india, H4-55/60 W-hi and low Beam. SOLD EACH
8-337 Eyeball bullet style headlight, 9-1/2” L (long body).8-338 Eyeball bullet style headlight, 8-1/2” L (short body).
B. EYEBALL BULLET STYLE HEADLIGHTS
B
Chromed aluminum headlights are w/o tri-bar, 3-1/2” in dia, 5-1/2”long, 12V H4-55/60W-hi and low Beam. SOLD EACH
8-339 Headlight w/visor.8-340 Headlight w/o visor.
C. CHROME HEADLIGHTS
C
U.S.A. MADE light bars designed for use with National Cycle’s HeavyDuty windshield series. Light bars are fully assembled and are pre-wired for easy installation. Includes turn signals. Chrome plated.
11-116 For XL 1987 & later, Dyna® 1993 & later, SOLD AS KIT
FXR & FXRS 1982 thru 1994, andFXLR 1987 thru 1994. (Narrow Glides®).
11-117 For FXDWG 1993 & later, FXWG 1980 thru 1985,FXDG 1983, FXST/I 1984 thru 1990 and1999 & later, FXSTD/I 2000 & later,FXSTB/I 1999 & later, and FXSTC 1987 thru 1999.Will not fit FXSTF.
E. SPOTLIGHT BARS
CHROMEPLATED
Chrome plated spotlight bars with distinctive V-styling. Check out theV-style rear signal kit on page 1-36.
11-147 Fits FLST 1986 thru 2003. SOLD EACH
11-148 Fits Road King® 1994 thru 2003.
D. V-STYLE SPOTLIGHT BARS
CHROMEPLATED
E
D
1/17
1A chrome plated reproduction of 1962 & later FL type spotlight. SAE Y97approved with H3 12V, 55 watt halogen bulb. One wire lead.
8-194 4-1/2” Late model spotlight, OEM 68652-64B. SOLD EACH
6-48 Replacement bulb only.8-127 Chrome assembly w/diamond cut reflector & 30 Watt bulb.8-143 Replacement composite light beam with 30 Watt bulb.8-144 Replacement composite light beam with 35/35 Watt bulb.
CHROMEPLATED
A. 4-1⁄2” LATE MODEL SPOTLIGHT
Classically styled 5-3/4” chrome headlights come completely assem-bled. Includes blue high beam indicator and mounting block. DOT 9809approved. 12V; includes a 55/60 watt H4 bulb. Brighter is better!
8-195 Bottom mount headlight. SOLD EACH
8-196 Side mount headlight.CHROMEPLATED
B. 5-3/4” HEADLIGHTS
8-195BOTTOMMOUNT
8-196SIDE
MOUNT
Beautifully chromed 7” diameter headlight. OEM style, bottom mountFL style is perfect for restoration or custom FL applications. IncludesH4 55/60 watt bulb. No high beam indicator. DOT 9913-A approved.
8-197 7” headlight. SOLD EACH
6-52 Replacement bulb only.
C. 7” CHROME HEADLIGHT
Chrome plated mini headlight designed for use on highway bars asadditional lighting. 12V, 30 Watt sealed beam, Hi-Lo indicator light, andbottom mount are all included. Parts also available separately.
8-137 Complete headlight with sealed beam. SOLD EACH
7-53 Replacement sealed beam only.6-55 12V Indicator bulb only.
CHROMEPLATED
D. 4-1⁄2” MINI HEADLIGHT
CHROMEPLATED
DIAMOND CUTREFLECTOR
A
B
D
C
E
The below lights with diamond cut reflectors have 35/35 Watt bulb.
8-112 Chrome assembly with diamond cut reflector. SOLD EACH
8-143 Replacement composite light beam with 30 Watt bulb.8-144 Replacement composite light beam with 35/35 Watt bulb.
E. CHROME SPOTLIGHT
CHROMEPLATED
Complete stretched headlight shell assembly (less bulb) has a smoothcontoured retaining ring and unique domed shape. Lights are soldwithout sealed beam. Parts also available separately.
8-151 For FXSTS Softail Springer® 1993 & SOLD EACH
later; stock replacement.8-152 For FXDWG, FXST & FXWG, 1980 & later and
FXSTS 1988 thru 1992. With bates style tabs &mount block. Also for use on custom applications.
ALSO PURCHASE7-39 6V Replacement sealed beam. SOLD EACH
7-25 12V Replacement sealed beam.7-26 12V Sealed beam — quartz halogen. 5-3⁄4” Dia.
Replaces OEM 67698-81B.7-52 12V “Motorcycle” sealed beam — halogen.
5-3⁄4” Dia. Replaces OEM 67698-81B.
CHROMEPLATED
F. 5-3⁄4” STRETCHED HEADLIGHTSF
1/18
1
Allows the use of a 1-wire (horn button).type switch to operate high/low beam headlights on 12V systems.Perfect for custom handlebar switch set-up.
17-116 Headlight relay. SOLD EACH
E. HEADLIGHT RELAYE
B. BULLET STYLE HEADLIGHT & SPOTLIGHTWITH ACCENT LINES
Chrome plated, 12V lights with bullet styling and ball mill style accentlines. 3⁄8-24 Bottom stud mount.
8-145 4.5” Spotlight. SOLD EACH
8-146 5.75” Headlight.
Replacement spotlamp housing for OEM 68671-69. Used on 1965 &later Big Twin. Mounts like stock passing light.
8-138 Spotlamp with sealed beam. OEM 68671-69. SOLD EACH
8-95 Spotlamp housing only.7-51 12V, 30W replacement sealed beam only.
Wagner #4449, 2 screws.Spotlight mounting bracket sets.11-100 For early FL, 1949 thru 1961. SOLD AS PAIR
OEM 68603-49 & 68604-49.11-54 For late FL, 1961 thru 1984. OEM 68603-62.11-201 Springer style. For FLST 1984 &
later. OEM 58092-87.
ALL PARTSCHROMEPLATED
11-54
8-138
C. SPOTLIGHT & BRACKETS
CHROMEPLATED
8-78 Complete light without sealed beam for Sportster®1954 thru 1973 and Super Glide®1971 thru 1974. OEM 67733-72.
8-89 Complete light without sealed beam forSportster® 1974 & later and Super Glide®1975 & later. OEM 67743-75.
86-58 Rubber ring only. OEM 67719-63.7-25 12V sealed beam.7-39 6V sealed beam. SOLD EACH
CHROMEPLATED D. SPORTSTER®/ SUPERGLIDE® STYLE
HEADLIGHT
A. CUSTOM HEADLIGHT SHELLSThese custom shells really open your options for making the perfectcustom headlight for your bike. Pick a custom headlight of your choiceto get exactly the look you want.
Die cast aluminum housing weighs less than heavy billet aluminumshells. Pure custom at a budget price.
5-3/4” DIAMETER SHELLS
8-203 Smooth shell. SOLD EACH
7” DIAMETER SHELLS8-201 Smooth shell. SOLD EACH
8-202 Flamed shell.4-1/2” DIAMETER SPOTLIGHT SHELLS
Custom spotlight shells match our headlight shells above. Pick a styleof custom spotlight found on page 1-13.
8-205 Smooth shell. SOLD EACH
8-206 Flamed shell.
CHROMEPLATED
FLAMEDSMOOTH
11-201
A
B
C
D
1/19
1
“Hi-Lo” beam indicator light glows when high beam is on. 5.70”Diameter sealed beam.
8-16 12V Bottom mount sealed beam head- SOLD EACH
lamp. Mounting bolt included.8-139 12V Bottom mount sealed beam headlamp with
halogen motorcycle sealed beam.86-69 Replacement chrome ring.7-39 6V Replacement sealed beam.6-54 6V Replacement indicator bulb.7-25 12V Replacement sealed beam.7-26 12V Sealed beam — quartz halogen. 5-3⁄4” Dia.
Replaces OEM 67698-81B.7-52 12V “Motorcycle” sealed beam — halogen.
5-3⁄4” Dia. Replaces OEM 67698-81B.6-55 12V Replacement indicator bulb.
Headlamps fit Big Twin models using Wide Glide® forks. Lights aresold without sealed beam.
8-77 Headlamp for 1949 thru 1959; like original, SOLD EACH
without hi beam indicator. OEM 67701-49. Includesmounting bracket part No. 11-45.
ALSO PURCHASE7-47 Sealed beam 12V. SOLD EACH
7-42 Sealed beam 6V.7-45 Quartz unit 12V.11-45 Mounting bracket for part No. 8-77 (see page 1-21).
CHROMEPLATED
BOTTOMMOUNT
86-103
Headlight Conversions are exact replacements for sealed beam usedon most big bikes. They provide substantially improved lighting withlittle or no modifying, at a modest cost. A dual filament bulb allowshigh or low beam operation. Quartz iodide/350,000 candlepower.
7-45* Quartz unit 12V, 7” dia. SOLD EACH
7-46* Quartz unit 12V, 5-3⁄4” dia.6-52 12V Replacement bulb, 60/55W.6-61 12V Replacement bulb, 100/55W.6-32 6V Replacement bulb, 60/55W.
*For 6V applications — order 12V conversion kit and replace bulb withour part No. 6-32 H4 bulb.
D. 7” H-D® STYLE HEADLAMP
A. CONVERSION HEADLIGHTS
B. SEALED BEAM HEADLAMPS
C. 7” FAT BOY® & HERITAGE® STYLE HEADLAMP
Lamp is sold without sealed beam.
8-147 Headlamp for 1986 & later Fat Boy® & SOLD EACH
Heritage®. Replaces OEM 67789-91. Bottommount — includes mounting block.
ALSO PURCHASE7-47 Sealed beam 12V. SOLD EACH
7-42 Sealed beam 6V.7-45 Quartz unit 12V.86-103 Mounting block kit (OEM 67768-86), and hardware.86-104 Rim kit (OEM 68050-93, 68051-93, and three
of 68052-93).
CHROMEPLATED
86-104
8-147
A
B
C
DCHROMEPLATED
1/20
1
This new headlight is manufactured from spun aluminum & then showchrome plated. Headlamp unit is secured with a threaded chrome plat-ed bezel that is sealed with an O-ring. Complete with 5-3/4” halogenheadlight unit and 12V, 60/55 watt, H4 halogen bulb. Bottom mount.
8-182 5-3/4 Headlamp. SOLD EACH
8-183 Same as above part No. 8-182 except with blue halogen bulb.
86-2 Mounting block for headlight SOLD EACH
Replacement bulbs for part No. 8-182 see page 1-12.Replacement bulbs for part No. 8-183 use bulb part No. 6-63.
Bottom mount headlight has two H3 12V/55 w bulbs. The housings arehand polished and chrome plated. They are ECE approved for highbeam and fog lamp. Measures 152mm x 70.4mm x 60.6mm.
8-315 Headlight with Clear lens. SOLD EACH
8-316 Headlight with Blue lens.8-317 Blue replacement lens.8-318 Clear replacement lens.
A. ‘WAVE’ HEADLIGHTS
ACHROMEPLATED
B. 5-3/4” BULLET STYLE SPUN ALUMINUMHEADLAMP
B
This Cateye Headlight Assembly w/12 volt 60/55 - watt H4 bulb, mea-sures 7” long x 5” wide x 3 7/8”
8-322 Crome billet aluminum headlight. SOLD EACH
F. CATEYE HEADLIGHT ASSEMBLY
CHROMEPLATED 8-141 Headlamp with sealed beam. SOLD EACH
7-54 Replacement 12V sealed beam.
C. 5-1⁄2” BULLET SEALED BEAM HEADLAMP
C
E. 7” BULLET SEALED BEAM HEADLAMP
CHROMEPLATED
7” Bullet style 12V headlamp similar to the early Springer®
headlamp with high beam indicator light.
8-140 Headlamp with sealed beam. SOLD EACH
7-47 Replacement 12V sealed beam.
E
F
CHROMEPLATED
8-212 5-3/4” headlight w/frenched trim ring. SOLD EACH
D. 5-3/4” BULLET HEADLIGHTD
1/21
1
Light bolt size is 1⁄2”, mounting holes for the bolts are 4-1⁄2” to 5-1⁄4”apart. Fits most motorcycles with pinch bolts on lower tree.
11-42 For Sportster®, Super Glide® & narrowcustom trees. SOLD EACH
Custom headlight brackets to mount 7” headlights.
11-108 For late Sportster®, FX and custom SOLD EACH
narrow triple trees. 4-1⁄2” Center to centermounting holes.
11-109 For Wide Glide® and early Sportster®. 2-1⁄2”Center to center mounting holes.
To mount M.W. part No. 8-77 7” headlight to H-D® Big Twin WideGlide® front fork.
11-45 For 1949 thru 1976. OEM 67810-48. SOLD EACH
11-51 For 1977 & later. Fits all FXWG front ends.4” Center to center mount. 5⁄16” Mounting hole.
CHROMEPLATED
11-40 For early Sportster® & Wide Glide®. SOLD EACH
40-551 Chrome Horse® headlight bracket SOLD AS KIT
screw kit with stainless steel button head allens.
CHROMEPLATED
CHROMEPLATED
CHROMEPLATED
A. HEADLIGHT BRACKET FOR SPORTSTER® &FLH WIDE GLIDE®
D. HEADLIGHT MOUNT FOR HYDRA GLIDE™
E. BOTTOM MOUNT HEADLIGHT BRACKET
F. HEADLIGHT MOUNTING PLATES
C. CUSTOM HEADLIGHT BRACKETS
11-109
11-108
11-59 11-113
11-59 Fits FXWG 1980 thru early 1985 and SOLD EACH
FXST/C, 1984 & 1985. OEM 67773-80.11-113 Fits FXST/C 1986 & later. SOLD EACH
OEM 67773-80A.40-551 Chrome Horse® headlight bracket SOLD AS KIT
screw kit with stainless steel button head allens.
Headlight bracket to fit bolts spaced 3-1⁄4” to 5-3⁄4” apart. Fits boltsize 5⁄8’’ or smaller. 12” Hole for headlight.
11-10 Headlight bracket. SOLD EACH
CHROMEPLATED
Beautiful brackets for mounting a custom side mount headlight. 3⁄8”Hole for headlight bolt.
11-26 Two adjustment slots to fit any size SOLD AS PAIR
fork tubes except Wide Glide®.
G. SIDE MOUNT BRACKETS
B. SINGLE HEADLIGHT BRACKET
B
C
DE
F
A
G
11-155 Mounts headlight to the bottom bolt of the shock absorber on Paughco springers. SOLD EACH
11-156 For Wide Glide triple trees.11-157 For FLST with tin covers.11-158 7/8” tall post.11-159 For 1993-1999 FXSTS.
H. HEADLIGHT BRACKETS
H
11-155
11-156
11-159
11-158
11-157
1/22
1
89-257 For FL 1960 & later. OEM 67847-60 & SOLD AS SET
OEM 67848-60.86-70 Headlight rim, gasket & spring clips. SOLD AS KIT
Fits FL & FLH 1960 thru 1980. OEM 67712-60A.89-107 Visor for all 7” Big Twin headlights SOLD EACH
1949 & later, also part No. 8-77. OEM 67752-77T.
89-257CHROMEPLATED
ALUMINUM
86-7089-107
B. HEADLIGHT HOUSING FOR FL
C. FRONT FORK & HEADLAMP TRIM FOR FLChrome plated or stainless steel.
89-139 Stainless steel front fork panel. SOLD EACH
OEM 46273-49.89-140 Stainless steel rear right fork panel. OEM 46283-49.89-141 Stainless steel rear left fork panel. OEM 46281-49.89-278 Chrome plated rear left fork panel.
A. FORK TIN FOR HERITAGE SOFTAIL® & FAT BOY®
Chrome plated steel tins to give that “antique” look. Chrome hardwareincluded.
89-349 Fits all Heritage Softail® and Fat SOLD AS KIT
Boy®, 1986 & later. Replaces OEM 67808-86,67816-86 & 67820-86.
CHROMEPLATED
89-141LEFT
89-140RIGHT
Chrome plated steel with six different center styles to choose from. Noneed to replace your bulb with a big-buck over-powered aviator bulb.Holds in place with headlight trim ring. U.S.A. MADE – A/C.
D. A/C TRI-BAR HEADLIGHT TRIM 5-3⁄4” AND 7”
FOR FOR5-3⁄4” DIA. 7” DIA. DESCRIPTION
89-420 89-426 Trim ring with long chrome bullet.
89-422 89-428 Trim ring with short chrome bullet.
— 89-429 Trim ring with glass amber dot.
89-424 89-430 Trim ring with glass blue dot.
SOLD EACH
A
B
C
D89-426
1/23
1
L.E.D. TAILLIGHTSWhy use L.E.D. taillights
➤ Low current draw — very efficient.➤ Does not generate heat.➤ Two times brighter than a halogen bulb.➤ More vibrant red color.➤ Vibration proof — no filament to break away.➤ Life expectancy is 100,000 hours.
➤ Flush mount lights are almost invisible when not energized.
8-9 Large tear drop; 4-1/2” x 2” red lens. SOLD EACH
8-10 Small tear drop; 3-5/8” x 1-5/8” red lens.
L.E.D. LIGHTS AND CONVERSION KITS - BY HITECH
LIGHTEMITTINGDIODES
L.E.D. CONVERSION ARRAYS FOR POPULAR TAILLIGHT STYLESThese L.E.D. inserts bring high tech and high visibility to pre-existingtaillight installations. Easily replaces the backing plate & bulb connec-tors in various taillights.
8-2 Array for cateye taillights. SOLD EACH
8-3 Array & smooth lens for cateye taillights.8-4 Array only for custom Fat Bob® taillights
part No. 8-129, 8-131 & 8-133 on page 1-25.8-5 Array only for 1973 thru 1999 OEM style taillights.8-6 Array only for tombstone taillights.8-7 Array & smooth lens for tombstone taillights.8-8 Array only for 1955 thru 1972 OEM style taillights.
CHROMEPLATED
8-4
8-8
8-5
TAILLIGHTNOT INCLUDED
L.E.D. CONVERSION KITS FOR FXST & FXDWGDeep chrome brackets with single or double row L.E.D. light arrays. Used as running and brake lights.
➤ Smooth red lens: Emits a brighter beam type light and allows each individualL.E.D. to show behind lens.
➤ Prism red lens: Diffuses the light to give an appearance much like a stock lens.
Also in this group is the new L.E.D. with turn signals (available in double row only). Approximately
1-1/4” ends on each side function as turn signals — very clean. A Badlands Load Equalizer
found on page 1-35 must be used with the turn signal kit.
All below kits include bracket.
FXDWG DESCRIPTION LENS
8-169 Double row Prism red lens
8-171 Double row with turn signals Prism red lens
SOLD AS KIT
8-3
8-7
8-9
1/24
1 A. COMPLETE L.E.D. TAILLAMPASSEMBLIES
LED lamps use high grade bulbs that emit the brightest light and theyall are encased in epoxy resin to stop vibration and moisture damage.Check the number of LEDs in each assembly — the larger the numberof LEDs the brighter the taillamp. These are top quality. SOLD AS KIT
FOUR
MOST
POPULAR
STYLES
B. SKULL LENS CATEYE TAILLIGHTSCHROMEPLATED
8-221LENS
8-222LENS
These new taillights feature a raised skull molded into the lens. Allhave a new body design with stepped profile that gives a custom“machined” look. Taillights are 12V and are supplied with conventionalbulbs installed.
LENS STYLE WITH BULB WITH LEDs
Clear skull with Red lens. 8-220 8-223
Red skull with Clear lens. 8-221 8-224
Clear skull with Clear lens. 8-222 —
(Red bulb) SOLD AS KIT
Beautiful oval taillight with large license illumination lens. Flat backfor universal mounting. Mounting screws 2” center to center. Willmount on part No. 11-39 taillight mount, but for something special, useon the CHROME HORSE® stainless steel side mount part No. 11-120.
8-79 12V Taillight with plain lens. SOLD EACH
8-136 12V Taillight with blue dot lens.8-2 LED Conversion array for cateye taillights.86-71 Red plain lens only.86-98 Blue dot lens only.
E. CATEYE TAILLIGHT
D. CUSTOM CATEYE TAILLIGHTS WITH LEDARRAY
CHROMEPLATED
This cateye taillight is complete with LED array. Available in two lenscolors — either red or clear. Although the LED array appears to haveclear elements, when lit, the clear lens taillight shines red. Mountingscrews 2” center to center. Will mount on the CHROME HORSE®stainless steel side mount part No. 11-120 seen on page 1-38.
8-185 12V LED taillight with clear lens. SOLD EACH
8-186 12V LED taillight with red lens.Similar to above cateye taillights except with stepped style housing.8-261 12V LED taillight with clear lens. SOLD EACH
8-262 12V LED taillight with red lens.
8-185CLEARLENS
8-261STEPPEDHOUSING
Our new late H-D® style taillight features an LED array for those whowant the brightest taillight available.
8-193 Fits XL, FX & all Big Twin 1973 SOLD EACH
& thru 1999. Replaces OEM 68008-73.
CHROMEPLATED
C. LATE STYLE L.E.D. TAILLAMP
8-220
CHROMEPLATED
PART RED WHITE CURRENT NO. DESCRIPTION LEDs LEDs DRAW RUN BRAKING
8-11 Cateye 60 3 3.75w 6w
8-19 Cateye conversion array only 60 3 3.75w 6w
8-12 Stock style 1973 / 1999 80 3 5.25w 9w
8-13 Tombstone 48 3 3w 4.5w
8-14 Fat Bob® style 60 3 3.75w 6w
A
B
C
D
E
1/25
1
D. CUSTOM FAT BOB® STYLE TAILLIGHT WITHINTEGRAL TURN SIGNALS & CUSTOM GRILL
This new custom taillight is designed to fit FXSTC & FXWG models orany custom application using a Fat Bob® style rear fender with cus-tom tail light brackets. Special features include a smooth radius shapethat will blend with the shape of fat bob fenders, a custom slotted grillface, integral turn signal lights, and clear lens on bottom with licenselight.
8-124 Custom Fat Bob® taillight with SOLD EACH
integral turn signals. Chrome plated.
CHROMEPLATED
F. SEMI-DIAMOND L.E.D. TAILLAMP CHROMEPLATED
Die cast chrome with LED array of 37 red and 4 amber.
8-156 Custom taillight. SOLD EACH
This chrome plated custom taillight with smooth style lens is designedto fit 1973 thru 1999 models or any custom application using a FatBob® style rear fender with custom taillight brackets.
8-199 Custom taillight with smooth lens SOLD EACH
and conventional style taillight bulb.
B. CUSTOM FAT BOB® STYLE TAILLIGHT WITHSMOOTH STYLE LENS
CHROMEPLATEDChrome plated die cast 12V taillight. Flat back with 2” center to center
holes for easy mounting.
8-132 Standard bulb illumination. SOLD EACH
8-215 With LED illumination .
CHROMEPLATED
C. MALTESE SHAPED TAILLIGHTS
A. CUSTOM CATEYE TAILLIGHT & BRACKET
CHROMEPLATED
Die cast, chrome plated fender mount bracket is included.
8-289 12V LED taillight with clear lens. SOLD EACH
Die cast chrome with LED array.
8-285 Custom taillight. SOLD EACH
E. DIAMOND L.E.D. TAILLAMP
A
B
C
D
E
F
G
CHROMEPLATED
G. CATEYE L.E.D. TAILLIGHT ASSY.
Custom cateye LED taillight assy. w/turn signal function.
8-341 Cateye L.E.D. taillight assy. SOLD EACH
H
H. DRILLED TAILLIGHTS
Custom taillight assy. w/license bracket.
★8-216 Drilled taillight, brass. SOLD EACH
★8-217 Drilled taillight, aluminum.
1/26
1 A. THE ORIGINAL CHOPPER TAILLIGHTThe first chopper builders choose these taillights for the combinationof toughness and small size. They held up well on “bone-rattlin” hard-tails. Die cast, chrome plated. Due to small size of lens, use only forshow and restoration purposes. Not DOT approved.
11-143 12V Taillight, red lens, conventional SOLD EACH
style taillight bulb.8-302 12V Taillight, red lens, LED illumination .
8-301 Same as above part No. 11-143 except polished.86-155 Replacement lens for above taillights.
A
B. EXTENDED LENS SPARTO TAILLIGHTThis sparto taillight features a new extended round lens for a newlook. Hardware included.
11-131 Sparto taillight, extended lens. SOLD EACH
B
C. CUSTOM TOMBSTONE TAILLIGHTS WITH LED ARRAY
8-266 12V LED taillight with red skull lens. SOLD EACH
C
Includes mounting gasket and license mount. 12V.
8-70 Taillamp. OEM 68002-47. SOLD EACH
86-45 Red lens only.11-53 License bracket only.
NOTE: Taillight not recommended for street use.
CHROMEPLATED
D. BEEHIVE TAILLIGHT 1939 thru 1946
D
E. WIDE TOMBSTONE TAILLIGHT WITH LED ARRAY
Our new wide tombstone LED taillight has the styling of the originalequipment taillight except it has been redesigned to fit 1973 & later OEfenders. Fits all Big Twin models 1973 thru 1999 (except FLSTS & mod-els with Fat Bob® style rear fenders) and Sportster® models 1973 thru1998. Models with fender mounted turn signal light bar require reloca-tion of the light bar.
8-192 Wide tombstone LED taillight. SOLD EACH
8-198 Same as above part No.8-192 except withconventional style taillight bulb.
E
1/27
1
12 Volt bulb included. U.S.A. MADE.
8-65 Fender mount. SOLD EACH
8-62 Side mount.
D. CUSTOM LICENSE BRACKET & TAILLIGHT
CHROMEPLATED
8-65
8-62
Under fender mount like FXWG models. Due to slotted mounting holesfor taillamp, various custom lamps can be used. Two types to choosefrom — wide for Fat Bob® fenders on FXWG & Softail®, or narrowfor FX & Sportster® width rear fenders.
11-76 Wide bracket for Fat Bob®, FXWG SOLD EACH
and Softail®.11-77 Narrow bracket for FX and Sportster®.
CHROMEPLATED
Exact replica of H-D® OEM 59993-80A. Fits FXWG stock fender andpart No. 19-50 fender for custom application.
11-47 Painted flat black. SOLD EACH
11-55 Chrome plated.
E. LICENSE PLATE & LIGHT BRACKET
F. LICENSE PLATE & LIGHT BRACKET
D
E
F
B. TOMBSTONE TAILLIGHTTombstone taillights are available in both standard 12V bulb or withLED array. Both are all metal replica of H-D® early style taillight usedas original equipment on 1947 thru 1954 models, OEM 68003-47T.Superbly crafted & chromed. Universal fender mounting for most appli-cations. Includes chrome plated license mount, black rubber mountinggasket for paint protection, and either 12V bulb or LED array.
8-56 Complete taillight with 12V bulb. OEM 68003-47. SOLD EACH
8-191 Complete taillight with LED array.8-6 LED Conversion array ONLY for
tombstone taillights. See page 1-23.8-7 LED Conversion array & smooth lens
for tombstone taillights. See page 1-23.86-34 Red replacement lens. OEM 68090-47.
NOTE: Taillight not recommended for street use.
CHROMEPLATED
Beautiful all-metal, show chrome housing with the latest in taillightlens optics. Strong flush mounting. Includes 12V bulb.
8-73 Taillight. SOLD EACH
A. FLUSH MOUNT TAILLIGHT
A
B
C
C. MINI LED TOMBSTONE TAILLIGHTThese taillights feature a red LED array and measure approximately4.5” long and 2.5” wide.
8-211 Mini Tombstone taillight, w/ license plate bracket.SOLD EACH
8-191
1/28
1
Adjustable taillight/license bracket is perfect for use with our FatBob® style fenders for wide frames. Adjustable from 7.5” to 9” wide.Use with taillamp part No. 8-133.
11-48 Taillight bracket for wide rear fender. SOLD EACH
Classic cateye style taillight with the chrome plated taillight/
license plate bracket. Fits FXWG and FXST models 1980 & later.
8-134 Taillight and bracket kit. SOLD AS KIT
Bring back that nostalgic look by customizing any lens with the BlueDot. Can be installed by drilling hole in lens and is held in place bychrome ring. May not be approved in some states.
86-72 Chrome ring & blue jewel. SOLD EACH
E. BLUE DOTS
RINGCHROMEPLATED
A. CUSTOM FAT BOB® STYLE TAILLIGHT &BRACKET KITS
Custom Fat Bob® style taillights come complete with a chrome platedmounting bracket. Fits FXWG and FXST models 1980 & later.
8-129 Complete taillight kit with stock style SOLD AS KIT
taillight mounting bracket.8-131 Complete taillight kit with custom style. SOLD AS KIT
taillight mounting bracket.8-133 Taillight only for above kits. SOLD EACH
8-4 LED Conversion array only for above SOLD EACH
custom Fat Bob® style taillights partNo. 8-129, 8-131 & 8-133.
BRACKETSCHROMEPLATED
8-129
8-131
B. CATEYE TAILLIGHT and BRACKETCHROMEPLATED
C. ADJUSTABLE TAILLIGHT & LICENSEBRACKET FOR WIDE FENDERS
CHROMEPLATED
11-32 U.S.A. MADE license bracket fits SOLD EACH
various license back plates, or mount plate directly.
CHROMEPLATED
D. SIDE MOUNT LICENSE BRACKET
A
B
C
D
E
F
F. EURO LED TAILLIGHT8-325 Euro LED taillight for ‘73-’98 HD models. Features a
chrome backing plate included & 36” of protective coatedcolor coded wiring for easy installation. SOLD EACH
8-326 Euro LED taillight for ‘99-present HD models. Fits exist-ing backing plate & screws & has 5” color coded wiring foreasy installation. SOLD EACH
8-3268-325
Chrome die cast taillight with stainlessstrap license bracket.
8-254 Taillight assy. with standard bulb. SOLD EACH
8-288 Taillight assy. with LED illumination.86-138 Replacement red lens for above part No. 8-254.86-137 Replacement red lens for above part No. 8-288.
CHROMEPLATED
G. VINTAGE TEARDROP TAILLIGHT
G
1/29
1
CHROMEPLATED
8-255Chrome die cast taillight housing with twin bulbs.
8-255 Taillight assembly with two 12V bulbs SOLD EACH
and aluminum license plate bracket.8-256 Taillight only.8-257 Aluminum license plate bracket only.
C. TWIN BULB CUSTOM CATEYE TAILLIGHT
C
B. EARLY H-D® STYLE TAILLIGHT & LENSOriginal style taillight in chrome, with 12V bulb. Fits 1955 thru 1972Sportster®, Big Twin, and many custom applications.
8-59 Chrome plated taillight. SOLD EACH
OEM 68010-64B.8-8 LED Conversion array only for 1955 thru 1972
OEM style taillights. See page 1-23.11-44 License bracket; 2 hole. OEM 59995-55A.11-99 License bracket; 3 hole. OEM 59998-75T.86-41 Red lens only. OEM 68090-69.
License bracket screw kit with Chrome Horse® stainless steel buttonhead allen screws and nylon insert lock nuts.
40-552 Fits all models with 3 hole license SOLD AS KIT
plate bracket.40-553 Fits all models with 2 hole license plate
bracket.
CHROMEPLATED
8-59
11-44
86-86
86-4111-99
Original style taillight for XL, FX, and all Big Twins 1973 thru 1999.
8-74 Taillight with 12V bulb. OEM 68008-73. SOLD EACH
8-5 LED Conversion array & lens for 1973 thru 1999OEM style taillights. See page 1-23.
86-132 Clear lens only. Fits 1957 thru 1972 FL & XL.86-133 Clear lens only. Fits 1973 thru 1998 FL, FX & XL.86-42 Lens only, plain. OEM 68034-77.86-79 Lens only with Blue Dot installed.86-100 Lens only with Blue Dot chevron grill.78-169 Gasket only. OEM 68123-73.89-321 Taillight trim grill with chevron for above part
No. 8-74 taillight or OEM taillight on 1973 & laterBig Twin & Sportster®.
86-131 Lens only, for 1999 thru 2003. OEM 68140-99A.86-154 Lens only, fits late 2003 & 2004 wedge bulb.86-130 Laydown style lens only, for 1999 thru 2003.86-151 Laydown style lens only, with license lens facing
up. Fits late 2003 & 2004 wedge bulb.86-153 Laydown style lens only, with license lens facing
down. Fits late 2003 & 2004 wedge bulb.86-134 Clear laydown style lens only, with license lens
facing down. Fits 1973 thru 1998 and 1999 FLST.86-152 Clear laydown style lens only, with license lens
facing down. Fits late 2003 & 2004 wedge bulb.86-135 Clear lens with reflector assy. Fits 1999 thru 2003
FLT.86-136 Clear laydown style lens with reflector assy. and
with license lens facing up. Fits 1999 thru 2003 FLT.86-150 Clear laydown style lens with license lens facing
up. Fits late 2003 & 2004 wedge bulb.
86-79
86-42
8-74 CHROMEPLATED
89-321 CHROMEPLATED
86-150
A. LATE H-D® STYLE TAILLIGHT
86-130
86-133
86-135
86-134
86-154
A
B
1/30
1
These chrome plated, die cast, quality replica fender lights includerubber gasket, wire, and 12V bulb.
8-97 Fender light with clear lens. SOLD EACH
8-98 Fender light with amber lens.
Chrome plated covers for popular style taillights.
89-390 Die cast skull cover gives a unique SOLD EACH
touch to your tombstone taillight. Fits alltombstone taillights.
89-391 Die cast cover with eagle fits all cateye taillightswithout blue dots.
89-392 Steel cover fits all cateye taillights with or with-out blue dots.
Die cast construction. Amber lens.
8-75 Fender light, 12V, 5⁄16” dual stud mount. SOLD EACH
OEM 59140-85T. NOTE: Taillight not recommended for street use.
CHROMEPLATED
89-392
CHROMEPLATED
89-391
E. 1950’S STYLE FENDER LIGHTS
B. FRONT FENDER LIGHT
A. TAILLIGHT LENS COVER
C. CHROME BILLET DERBY COVER AND SIDEMOUNT CURVED LICENSE BRACKET WITHTAILLIGHT
8-232 Fits 1999 & later Twin Cam 88®. SOLD EACH
With half moon LED taillight.8-233 Fits 1984 thru 1999 Big Twin. With half moon LED
taillight.8-234 Fits 1999 & later Twin Cam 88®. With diamond
LED taillight.8-235 Fits 1984 thru 1999 Big Twin. With diamond LED
taillight.CHROMEPLATEDBILLET 8-232
D. BIG TWIN FENDER LIGHTS
CHROMEPLATED
8-125
Reproductions of the popular fender trim lights used on Big Twins.These lights will work on all models with the large dresser style fend-ers. Don’t forget part No. 89-360 fender spear set found on page 2-35.
8-125 Front trim light with amber lens. SOLD EACH
OEM 59082-79.8-126 Rear trim light with red lens. OEM 59658-79.
LED Replacement for lights on FL type fender 1980 & later. Snaps intostock light fixture. No need for a load equalizer — just plug it in.
8-207 Red LED Rear fender light. SOLD EACH
8-234
8-235
A
B
C
D
E
89-390
1/31
1
Wedge style 12V marker light is chrome plated, 2” high x 3-1⁄2” long x1-1⁄4 “ wide.
8-114 Wedge light, red lens, standard bulb. SOLD AS PAIR
8-115 Wedge light, amber lens, standard bulb.8-178 Wedge light, LED’s with amber lens.
E. SPLIT LENS MARKER LIGHT/TURN SIGNALDie cast, chrome plated, flush mount marker light with split lens.
8-128 Marker lights with amber lens, standard bulb. SOLD AS PAIR
8-179 Marker lights with LED’s & amber lens.
F. WEDGE MARKER LIGHTSCHROMEPLATED
Custom marker lights of chrome plated cast alloy. The hooded lensopening & wedge shape make these marker lights stand out. BothKing and Queen are 12V. The King is available in single or double fila-ment models, the Queen in single filament only. The point-of-sale dis-play packaging lets the consumer view the light from all angles.KING MARKER8-93 Red light, dual filament. SOLD EACH
8-94 Amber light, dual filament.6-57 Replacement bulb; 12V, single filament. Will also
work with our bullet lights (at left).6-58 Replacement bulb; 12V, dual filament. Will also
work with our bullet lights (at left).QUEEN MARKER8-82 Red light, single filament. SOLD EACH
8-83 Amber light, single filament.6-55 Replacement bulb; 12V, single filament.
CHROME PLATED
A. KING & QUEEN MARKER LIGHTS
B. CUSTOM BULLET MARKER LIGHTSA beautiful copy of H-D® old style marker lights with either red, blueor amber lens, 12V bulb & hidden wire mounting base. Can be mountedanywhere.The below part numbers are with single element. Use replacementbulb part No. 6-57.8-55 Bullet light with red lens. SOLD EACH
8-102 Bullet light with amber lens.8-103 Bullet light with blue lens.The below part numbers are with dual element. Use replacement bulbpart No. 6-58.8-104 Bullet light with red lens. SOLD EACH
8-105 Bullet light with amber lens.8-106 Bullet light with blue lens.Replacement lenses for all above bullet lights.86-55 Amber lens only. SOLD EACH
86-53 Red lens only.86-54 Blue lens only.
CHROMEPLATED
D. RED CUSTOM BULLET LIGHTS WITH LED ARRAY
8-260 Chrome die cast housing with clear lens.SOLD AS PAIR SINGLE FILAMENT
C. MALTESE LED MARKER LIGHTS
8-271 Maltese, chrome billet housing with red lens. SOLD AS PAIR
CHROMEPLATED
A
B
C
D
E
F
8-82
CHROMEPLATED
D. CHROME BULLET LIGHTS
CHROMEPLATED
Bullet lights add a custom look to choppers or dressers. Single element,3” length, 1-1/2” from stand off to top, 5/16” mount stud with rubbergrommet.
SMOOTH
LEADBALLMILL
BULB BULB LED LED LENSSMOOTH BALL MILL SMOOTH BALL MILL COLOR
8-122 8-303 8-309 8-305 Amber
8-123 8-304 8-311 8-307 Red
— — 8-310 8-306 Clear
— — 8-312 8-308 Blue
SOLD AS PAIR
BALLMILL
C. MINI MARKER LIGHTSDiamond style 12V mini marker light is die cast, chrome plated, 2”wide x 1-1⁄4” high. Thru bolt wiring.
8-116 Diamond light, red lens. SOLD EACH
8-117 Diamond light, amber lens.Diamond style LED mini marker light is die cast & chrome plated, withthru bolt wiring.8-279 Diamond LED light, red lens. SOLD AS PAIR
8-280 Diamond LED light, amber lens.Bantam style 12V mini marker light is ABS chrome plated, 1-5⁄8” widex 1-1⁄4” high. Thru bolt wiring.8-118 Bantam light, red lens. SOLD EACH
8-119 Bantam light, amber lens.
CHROMEPLATED
DIAMOND
BANTAM
C
D
REPLACEMENT REPLACEMENT COLORLENS BULB
86-160 — Amber
86-163 — Red
86-161 6-116 Clear
86-162 — Blue
SOLD EACH
1/32
1These Hyper-lite custom designed marker light/mini spotlights aremade from aluminum & are beautifully chrome plated. They feature a12V halogen 35W bulb which can be easily replaced, & all necessarywiring & hardware. The visor is o-ring sealed for a water tight seal.They have special reflective mirror glass lenses. Two sets of lenses aresupplied with each pair for different applications or as replacements.Can be used as marker lights or mini spotlights. Approx. 4-1/4” long,O.D. 2-3/8”.
8-352 Hyper-lite with (2)clear & (2)smoke lens set. SOLD AS PAIR
8-353 Hyper-lite with (2)red & (2)amber lens set.
A. HYPER-LITE CUSTOM MARKER LIGHTS
A
These Hi-glide EU approved lights are made from billet aluminum &are beautifully chrome plated w/extra heavy duty LED’s. Easy toinstall & come supplied with all mounting hardware.
8-350 Hi-Glide dual amber LED light. SOLD EACH
O.D. 1.60” x 3.00” L x 3.40” W8-351 Hi-Glide red LED light.
O.D. 2.20” x 3.50”
B. HI-GLIDE INDICATOR/MARKER LIGHTS
B
1/33
1
17-125 12V Rectangular flasher. For XL 1965 & later, FL 1965 thru 1984, FLT 1980 & later, FX 1971 & laterand FXR 1982 & later. 12V Rectangular flasher.SOLD EACH
LOAD EQUALIZER17-132 Load equalizer. Used to prevent SOLD EACH
irregular lighting when small LED turn signals areinstalled.
B. FLASHERS
2-1/4” Diameter x 2-1/2” long, chrome plated, die cast halogen lightwith multi-faceted reflector. All lenses use a rubber gasket to seal theunit. NOTE: Not DOT approved — for show use only.
Clear 50w lights can be used as touring lights — really makes things“glow in the dark” (check the motorcycle’s charging system to be sure itcan handle this current draw).
Red lens units can be used as rear turn signals (35w).
Amber lens can be used as front turn signals (20w).
Universal mounts can be used where you can adapt them. Designed tofit most applications, it has a chromed steel center drilled 3/8-16 shoul-dered mounting post to hide the wires.8-175 50w Flood light, Clear lens.8-176 35w Rear light, Red lens.8-177 20w Front light, Amber lens.
REPLACEMENT PARTS86-115 One pair of Amber lenses. SOLD AS PAIR
86-116 Lens gasket. SOLD EACH
86-118 Chrome bezel. SOLD EACH
6-14 20W No. MR16 spot bulb. SOLD EACH
6-15 35W No. MR16 spot bulb. SOLD EACH
6-16 50W No. MR16 flood bulb. SOLD EACH
A. BEACON-2 HALOGEN LIGHTS
8-175
CHROMEPLATED
17-125SOLD AS PAIR
A
B
D. MARKER LIGHT MOUNTING KITKit includes four chrome plated mounting blocks and hardware formounting bullet lights and similar sized marker lights. This kit allowsfor vertical mounting of these types of lights at the top tree on 35mmfront forks, 1987 & earlier. Can be used at the rear on fender struts aswell as many other custom light mounting situations.11-104 Marker light mounting kit. SOLD AS KIT
CHROMEPLATED
E. CLEAR LENSES FOR DIRECTIONALSIGNALS
Clear lenses for front only or use with LED lights. NOTE: Some states do notallow clear lenses — check with your local authorities.
86-120 Clear lens. Replaces OEM 68457-86. SOLD EACH
86-121 Clear lens, flat, small. Replaces OEM 68571-63A.86-122 Clear lens, flat, large. Replaces OEM 68440-86.
86-120 86-121 86-122
Kit includes four lights with mounting hardware.
8-286 Fits 2000 thru 2002 Softail®, 1990 thru 2002 Sportster®and 1991 thru 2002 Dyna®. Replaces OEM 68005-99.
8-287 Fits 1988 thru 1999 Softail®. Replaces OEM 68007-99.SOLD AS KIT
C
D
E
C. BULLET STYLE DIRECTIONAL SIGNALS
CHROMEPLATED
1/34
1 A. DUECE™ STYLE DIRECTIONAL SIGNALLIGHTS
8-190 Duece™ style turn signal kit. This 12V, SOLD AS KIT
U.S.A. MADE, Duece™ style turn signal with dual filamentkit includes: qty. 2 of part No. 8-188 front signal withamber lens (OEM 68885-00), and qty. 2 of part No. 8-189rear turn signal with amber lens (wiring thru mount hole).
8-269 Duece™ style turn signal kit. This SOLD AS KIT
Duece™ style turn signal with dual filament kit includes:qty. 4 of part No. 8-188 front signal with amber lens (OEM68885-00 & 68972-00), and qty. 2 red lenses.
8-188 Complete front dual filament amber SOLD EACH
turn signal. OEM 68972-00.8-189 Complete rear dual filament amber SOLD EACH
turn signal with the wiring run thru the mounting hole.8-270 Complete rear dual filament amber SOLD EACH
turn signal. OEM 68977-00.86-123 Amber lens only. OEM 68973-00. SOLD EACH
86-124 Red lens only. SOLD EACH
86-125 Clear lens only (for use with LED bulb). SOLD EACH
B. LED TURN SIGNALS
CHROMEPLATED
8-272
11-205 8-272 Clear lens, fits 1986 thru 1992 FLH, SOLD AS PAIR
FLST, FXRT & FXRD (DOT approved).8-273 Bullet style with clear lens. SOLD AS PAIR
Fits 2000 & later (DOT approved).11-205 Front turn signal mount kit. Fits XL, SOLD AS KIT
FXD, FXST, FLSTF, FLSTS. Chrome plated.Replaces OEM 68226-03.
A
B
8-273
C. LED TURN SIGNAL KITSThese mini LED lights feature high quality wiring, bright LED’s, andall have dual wired function for custom use.
TURNSIGNAL SOLD EACH
8-342 Amber LED turnsignal.8-343 Red LED turnsignal.
TURNSIGNAL W/MOUNTING STUD SOLD AS PAIR
8-344 Amber LED turnsignal, w/53mm mounting stud.8-345 Red LED turnsignal, w/53mm mounting stud.
TURNSIGNAL W/CLAMP KIT SOLD AS PAIR
8-346 Amber LED turnsignal, w/41mm clamp kit.8-347 Red LED turnsignal, w/41mm clamp kit.8-348 Amber LED turnsignal, w/39mm clamp kit.8-349 Red LED turnsignal, w/39mm clamp kit.
C8-342
8-344
8-346
1/35
1These U.S.A. MADE brackets & hardware are available individually andwill work with all M.W. H-D® style turn signals.
11-78 Bracket to lamp. OEM 68477-73. SOLD EACH
11-79 Rear turn signal support with screw. SOLD EACH
OEM 68480-73.11-98 Rear turn signal support. OEM 68480-93. SOLD EACH
Fits Dyna Glide®, FXDL & FXDWG, 1993 andlater and Sportster® 1993 & later.
11-1 Rear turn signal support. OEM 68480-02. SOLD EACH
Fits Softail® FXSTI, FXSTFI, FLSTSI, FXSTST,and FXSTBI.
11-2 Rear turn signal support. OEM 68821-00. SOLD EACH
Fits Softail® FXSTD & FXSDI, 2000 & later.11-80 Handlebar clamp with screw. OEM 68487-82 SOLD EACH
& 68486-82A.11-81 Rear turn signal stud (1-7/8” long), with SOLD AS PAIR
nut. OEM 68493-87.11-82 Rear short stud only (1-1⁄4” long). SOLD AS PAIR
Moves signal in close for sleeker look.11-85 Rear short stud only (5⁄8” long). SOLD AS PAIR
11-83 Stud with spacer. OEM 68528-77A. SOLD EACH
11-86 Low head socket screw. OEM 4070. SOLD EACH
11-87 1⁄4” Chrome spacer. SOLD EACH
11-88 1⁄2” Chrome spacer. SOLD EACH
11-89 3⁄4” Chrome spacer. SOLD EACH
11-90 1” Chrome spacer. SOLD EACH
11-91 1-1⁄4” Chrome spacer. SOLD EACH
11-92 Chrome spacer assortment. Includes SOLD AS PKG.
one each of above individual spacers.
11-3 Directional signal mount kit for front SOLD AS KIT
signals for most H-D®. OEM 68185-00.
11-78
11-80
11-83
11-82& 11-85
11-8611-87THRU11-91
11-81
11-98
11-79
A. TURN SIGNAL MOUNTING HARDWARE for H-D®
11-1
11-2
Rear turn signal mount for all 4 speed FL 1974 thru 1984 and FLST 1986thru 1988.
11-72 Stock size. OEM 68510-74A. SOLD EACH
11-106 4” Shorter than stock.
CHROMEPLATED
B. REAR TURN SIGNAL MOUNTS for FL
17-132 Used to prevent irregular lighting SOLD EACH
when small LED turn signals are installed.
C. LOAD EQUALIZER FOR USE WITH LED’S
11-3
A
B
1/36
1
C. V-STYLE REAR TURN SIGNAL KITFits 1974 thru 1984 4 speed FL, 1986 & later Heritage Softail®, 1991 &later FLT, FLHT, FLHS, & Road King® models. Check out the V-stylespotlight mounting bar on page 1-13.
11-202 Chrome V-bracket only. SOLD EACH
11-203 Complete kit assembled with amber LED SOLD AS KIT
marker lights (extra red lenses included).8-241 LED Amber marker lights (extra red SOLD AS PAIR
lenses included).
11-202
11-203
8-241
CHROMEPLATED
Front signal swivel kit with extra retainer & receptacle ball.
11-204 Fits XL, FLSTC, FLSTS, FLSTF, FXSTS, SOLD AS KIT
FXD, FXDL & FXDWG.
A. TURN SIGNAL SWIVEL KIT
CHROMEPLATED
Chrome plated mounting hardware for FL turn signals, 1968 thru 1995.Can also be used on custom applications.
11-101 Kit; includes all items. Fits 1968 thru SOLD AS KIT
1982. OEM 68518-68.11-102 Clamp. 5⁄8” Dia. OEM 68795-68. SOLD EACH
11-103 Bracket. Fits 1968 thru 1995. SOLD EACH
OEM 68519-68.11-101
B. TURN SIGNAL MOUNTING KIT for FL
CHROMEPLATED
11-10211-103
D. LED TURN SIGNAL KITKit includes 2 front bullet style signals w/dual function amber LED’sand clear lenses, 2 front signal clamps for 41 mm forks. 2 rear bulletstyle signals w/dual function, red LED’s and clear lenses, and 2 rearDuece™ style mounts.
8-321 Turn signal kit SOLD AS KIT
A
B
C
D
1/37
1
C. DUAL FILAMENT AMBER TURN SIGNAL UNIT. FITS MOSTH-D® MODELS, 1986 & LATER.
8-99 Complete amber turn signal without threads. OEM68404-86.
8-150 Complete red turn signal without threads.8-200 Complete red turn signal with threads.86-83 Amber lens only. OEM 68457-86.86-84 Red lens only.86-92 Red lens with blue dot installed, only.86-120 Clear lens, for front only. SOLD EACH
DIRECTIONAL SIGNAL LIGHTS — ORIGINAL H-D® STYLE
A. THESE 12V, DOUBLE CONTACT (EXCEPT PART NO. 8-84) H-D® REPLICA TURN SIGNALS CAN BE USED ON ANY MOTORCYCLE.
8-85 Complete early amber turn signal. SOLD EACH
OEM 68557-70A.8-84 Complete single element early amber turn signal.8-86 Complete early red turn signal.86-87 Early amber lens only. OEM 68571-63A.*86-88 Early red lens only. OEM 68570-63.*86-93 Early red lens with blue dot installed, only.*86-121 Early clear lens, for front only.*
8-88 Complete late amber turn signal. SOLD EACH
OEM 68400-86.8-87 Complete late red turn signal.*86-89 Late amber lens only. OEM 68440-86.*86-90 Late red lens only.*86-94 Late red lens with blue dot installed, only.*86-122 Late clear lens for front only.*
*Chris Products
B. FLAT STYLE LENS SINGLE FILAMENT TURN SIGNAL AND RUNNING LIGHTS.8-107 Complete amber turn signal with SOLD EACH
threads. Dual filament.8-108 Complete amber turn signal light with threads.
Single filament.86-87 Amber lens only. OEM 68571-63A.86-88 Red lens only. OEM 68570-63.86-93 Red lens with blue dot installed, only.86-121 Clear lens, for front only.
D. AMBER TURN SIGNAL UNIT WITH SINGLE FILAMENT FORFX, FXR, & XL, 1973 THRU 1985.
8-71 Complete amber turn signal with SOLD EACH
threads. OEM 68514-73.8-101 Complete amber turn signal without threads.
OEM 68515-77A.86-50 Amber lens only. OEM 68483-73.86-85 Red lens only.86-91 Red lens with blue dot installed, only.
CHROMEPLATED
CHROMEPLATED
CHROMEPLATED
CHROMEPLATED
86-89
86-120
86-122
8-85
8-107
8-99
8-71
A
B
C
D
86-87
86-85
1/38
1 DIRECTIONAL SIGNAL LIGHT KITS — ORIGINAL H-D® STYLE
This 12V, U.S.A. MADE, late style turn signal kit includes:
MIDWESTOEM NO. PART NO. DESCRIPTION
68406-86 Signal w/amber lens.68487-82 & 11-80 Handlebar clamps68486-82A68477-73 11-78 Bracket to lamp.68480-73 11-79 Rear signal support.
86-84 Extra red lenses.86-92 Extra red lenses.
68457-86 86-120 Clear lens (available separately).
8-111 Late style (1986 & later) turn signal kit. SOLD AS KIT
This 12V, U.S.A. MADE, early style turn signal kit includes:
MIDWESTQTY. OEM NO. PART NO. DESCRIPTION
4 68514-73 8-71 Signal w/amber lens.2 68487-82 & 11-80 Handlebar clamps.
68486-82A2 68477-73 11-78 Bracket to lamp.2 68480-73 11-79 Rear signal support.2 86-85 Extra red lenses.
8-110 Early style (1973 thru 1986) turn SOLD AS KIT
signal kit.
12V, U.S.A. MADE , flat lens turn signal kit. A variable load flashersuch as part No. 17-125 (see page 1-80) must be used to activate lampassemblies. NOTE: Kit does NOT include any mounting brackets,clamps or extra lenses. They MUST be ordered separately.
8-109 Flat lens style turn signal kit. SOLD AS KIT
Replacement parts and mounting hardware for above kit:MIDWEST
OEM NO. PART NO. DESCRIPTION
8-107 Signal w/amber lens.68487-82 & 11-80 Handlebar clamps.68486-82A68477-73 11-78 Bracket to lamp.68480-73 11-79 Rear signal support.68570-63 86-88 Extra red lenses.68571-63A 86-121 Clear lens, flat, small.
1/39
1LOAD EQUALIZERDesigned to return amperage draw to the correct factory specificationwhen aftermarket marker lights are used to replace stock turn signalson H-D’s® which have a self-cancelling system. Can also be used inplace of a heavy duty flasher on early model bikes when small markerlamps with wedge bulbs are being used as turn signals.
17-83 Load Equalizer SOLD EACH
LOAD EQUALIZER IIPerforms the exact same function of part No. 17-83 above with theadded feature of allowing retention of the emergency flasher capabili-ty. This unit has a built-in thermoster which retains the resistors’ heatwhile your bike is functioning in the emergency flasher mode.
17-111 Load Equalizer II. SOLD EACH
LOAD EQUALIZER IIINew for H-D® equipped with the TSSM security/alarm module or theTSM turn signal module. This module works flawlessly with the newgeneration of H-D® modules and is compatible with virtually any ofthe custom turn signals available. Works great with halogens andLED’s too. Unlike others, this module allows your security system towork properly all the time.
If you have a security light that is not functioning correctly (stays onall the time) or your turn signals are blinking erratically, this modulewill solve any related problem. This new module produces absolutelyno heat and is also intended for 1991 & later standard turn signal mod-ules. This new solid state module has solved our problem of having touse ceramic resistors that produce unwanted heat.
➤ Will run emergency flashers for any amount of time.➤ The only load equalizer designed for parade use.➤ Solid state construction and waterproof.➤ This module has a built-in solid state flasher.➤ Works on any H-D® with self cancelers.➤ U.S.A. Made with quality components.
17-123 Load Equalizer III. SOLD EACH
This new module has been miniaturized while adding new &improved features. This will give any H-D® without the 1991 & laterself canceller the same similar convenient features. Includes simplewiring diagrams for stock OEM wiring, as well as custom wiring andalso will work well on custom manufactured motorcycle. Featuresinclude:
➤ Nine second timed flashing that automatically cancels.➤ Can manually cancel at any time (quick lane change).➤ Has built-in emergency flasher mode.➤ This module has a built-in solid state flasher.➤ Built-in load equalizer, runs LED’s up to 100 watts.➤ Measures 2-7/8” long, 1-3/8” wide, 7/8” deep.➤ Includes wire connectors and simple diagrams.
17-110 Automatic turn signal shut off Module III.SOLD EACH
Snap a set of red lenses into your rear stock turn signals andinstall the iIluminator module. Now your bike has 3 runninglights, hit your brake and you have three brake lights, touch yourturn signal button and you maintain your turn signal functionwhile the other side remains a running light, or if you’re braking, abrake light. This unit has a built-in Load Equalizer.
17-112 The Illuminator. SOLD EACH
17-83
17-110
A. LOAD EQUALIZERS
C. THE ILLUMINATOR
B. AUTOMATIC TURN SIGNAL SHUT OFF MODULE III
A
B
C17-112
1/40
1
D. VISORS
Standard 1973 thru 1999 taillight visor.
89-208 Fits all models 1973 & later mounted SOLD EACH
with license light up.
Replacement die-cast visor.
89-204 Visor, plain. OEM 67809-70. SOLD EACH
89-206 Fits FX & Sportster® 1975 thru 1985, SOLD EACH
FXR 1982 thru 1983, FXRS 1982 thru 1985.OEM 67809-75.
40-549 Chrome Horse® stainless steel head- SOLD AS KIT
light visor screw kit for FX & FXR, 1971 &later, and XL 1970 & later.
Steel stamped cover only for headlight visor.
89-83 Cover with no cut out for indicator lights. SOLD EACH
89-84 Cover with cut out for indicator lights.
CHROMEPLATED
CHROMEPLATED
89-243
89-97
89-95
89-96
89-98
Chrome molded taillight visor with four slots that will dress up the reartaillight.
89-397 Taillight visor for Big Twin and Sport- SOLD EACH
ster® 1973 thru 1999, except FXST and FXWG.
CHROMEPLATED
A. VISOR FOR H-D® LATE STYLE, ALL-PLASTICTAILLIGHT
B. HEADLIGHT VISORS & VISOR COVERS
C. CUSTOM TAILLIGHT VISORVISOR
VISORCOVER
APPLICATION PART NO. DESCRIPTION UNIT
Headlight 89-243 Fits Sportster® 5-3⁄4” headlights. Will also fit 7” headlight, but shorter & SOLD EACH
much more stylish than below part No. 89-107. OEM 67750-88T.Headlight 89-107 Fits all 7” Big Twin headlights 1949 & later part No. 8-77. OEM 67752-77T. SOLD EACH
Spotlight 89-97 Designed to fit the H-D® 6V or 12V spotlight. OEM 67783-78T. SOLD AS PAIR
Marker light 89-95 Designed to fit the bullet shaped marker lamps. OEM 67785-78T. SOLD AS PAIR
Turn signal 89-96 Designed to fit late style H-D® turn signals. OEM 67737-88T. SOLD AS PAIR
Taillight 89-98 Designed to fit H-D® 74” taillight 1955 thru 1972 part No. 8-59. SOLD EACH
OEM 68014-88T.
A
B
C
D
1/41
1These skeleton ornaments are available to fit 7” & 5-3/4” headlightvisors as well as stock harley taillights (slight curve). There is also aflat version for u niversal fit. They can be attached with many adhe-sives (not included). Make a statement with the “No. 1” version thathas its middle fingers raised.
89-673 Gold 7” visor ornament SOLD EACH
89-674 Chrome 7” visor ornament89-675 Gold 7” visor ornament, No. 189-676 Chrome 7” visor ornament, No. 189-677 Gold 5-3/4” visor ornament89-678 Chrome 5-3/4” visor ornament89-679 Gold 5-3/4” visor ornament, No. 189-680 Chrome 5-3/4” visor ornament, No. 189-681 Gold taillight ornament89-682 Chrome taillight ornament89-683 Gold taillight ornament, No. 189-684 Chrome taillight ornament, No. 189-686 Chrome flat ornament89-687 Gold flat ornament, No. 189-688 Chrome flat ornament, No. 1
A. MOTHERS CUSTOM CYCLES SKELETON ORNAMENTS
89-678
89-682
89-686
89-688
DETAIL
C. CHROME LICENSE PLATE HOLDERS
Chrome license plate holder used on most model H-D®. Mounts instock location of original.
11-44 License bracket; 2 hole. OEM 59995-55A. 11-99 License bracket; 3 hole. OEM 59998-75T.
Chrome Horse® license bracket screw kit with stainless steel buttonhead allen screws and nylon insert lock nuts.
40-552 Fits all models with 3 hole license plate bracket.40-553 Fits all models with 2 hole license plate bracket.
This light and license mounting plate adapts to most any cycle. It’smade from heavy 18 gauge steel, and measures 7” wide and 7” high.
11-39 Fits taillights part No. 8-73, 8-79, SOLD EACH
8-185, and 8-186.
11-44
11-99
B. TAILLIGHT LICENSE BRACKET
Die cast chrome plated license plate bracket has 3 hole mounting likestock H-D® bracket. Rubber spacers help eliminate vibration, and letsyou adjust plate angle.
11-96 Fits all H-D® models with 3 or 2 hole SOLD EACH
mounting. Can be used on many custom applications.
CHROMEPLATED
D. LAY DOWN LICENSE PLATE BRACKET
SOLD EACH
SOLD AS KIT
A
B
C
D
1/42
1
C. MALTESE KROMETSA decorative fastener that can be used anywhere on the bike but isbest suited for license plate mounting. Excellent finish and detail.Removable stud, nylock nut and washers.
41-99 Maltese krommets. SOLD AS PAIR
3/4”APPROX.
3/8”SHOULDER
5/8” SQUARE FACE
C
D. LICENSE PLATE BUSHING AND SPACER
Reduces an axle mounted license plate bracket hole from 1” to 3/4”.40-710 Bushing and spacer kit SOLD EACH
D
B. STAINLESS STEEL SIDE MOUNT LICENSEBRACKETS
Side mount license/taillight mounts are fabricated from heavy gaugestainless steel then show polished to a beautiful finish. Designed tomount on axle.
11-120 Left side bracket for 3/4” axle & cateye taillight. SOLD EACH
11-139 Right side bracket for 3/4” axle & cateye taillight.11-124 Left side bracket for 1” axle & cateye taillight.11-125 Left side bracket for 3/4” axle & diamond taillight.11-126 Left side bracket for 1” axle & diamond taillight.11-127 Left side bracket for 3/4” axle & cateye taillight with
extended arm to mount on inside of swing arm.11-128 Left side bracket for 1” axle & cateye taillight with
extended arm to mount on inside of swing arm.11-129 Left side bracket for 3/4” axle & diamond taillight with
extended arm to mount on inside of swing arm.11-130 Left side bracket for 1” axle & diamond taillight with
extended arm to mount on inside of swing arm.Side mount license brackets only (no taillight mount area).11-144 Left or right side license bracket for 3/4” axle. SOLD EACH
11-150 Left side license bracket for 1” axle with extendedarm to mount on inside of swing arm.
A. TILT-DOWN LICENSE PLATE MOUNTThis mount plate tilts your license plate back. Allows easier on/offwithout catching your foot on the straight-up type mount. It also lookscool! Fits 7” x 4” license plates.
11-146 For Road Glide®, FLT Standard and SOLD EACH
Road King®, 1999 & later. Replaces OEM 53385-00.CHROMEPLATED
11-12011-124
11-126
11-125
11-128
11-127
11-130
11-129
11-144
A
B
1/43
1A. BILLET SIDE MOUNT LICENSE, TAILLIGHT, AND BRAKE CALIPER SUPPORT BRACKETS
These side mount license, taillight and brake caliper support bracketsare CNC machined and beautifully “Show Chrome” plated. Licensemounts are horizontal and include billet license frame and all neces-sary mounting hardware. Now available with 36 LED taillight. Caliper support brackets accept all 4 piston billet calipers.
Fits all Softail® models 1987 & later.
11-141 Billet side mount license, taillight, and brake caliper support bracket, with LED taillight. Fits all “Wide Tire” Softail® style motorcycles. Accepts cateye taillight part No. 8-79, 8-185, and 8-186.
11-141 CHROMEPLATED
A
CC. CHROME LICENSE PLATE FRAME WITH TRUCKER GIRL TAILLIGHT
8-294 Side mount license plate frame with trucker girl LEDtaillight (vertical mount) chromed. For 7” wide x 4” talllicense plate, fits 86’-up Softail. SOLD EACH
B. ULTIMA BRAKE LIGHT LICENSE FRAMEThis frame is made from strong yet lightweight aluminum that ischrome plated to a brilliant shine. This sleek design maximizesplate visibility and features bright LED brake lights on either side.Great for an easy install that gives your bike a custom look!
11-121 Ultima Brake light license frame. SOLD EACH
B
PATENT# D564,429
License plate frame measures 7-1⁄4” x 4-1⁄4”.
11-37 Plain license plate frame. SOLD EACH
40-554 Chrome Horse® license plate frame SOLD AS KIT
screw kit with stainless steel button head allens,washers, and nylon insert lock nuts.
E. LICENSE PLATE FRAME
CHROMEPLATEDE
D. CUSTOM SIDE MOUNT LICENSE BRACKETThis horizontal side mount license bracket bolts to softail beltguard tabs and has a LED license plate light.
11-308 Left side horizontal mount. SOLD EACH
D
1/44
1 A. CHROME BILLET LICENSE PLATE FRAMEWITH DIAMOND LED TAILLIGHT
11-301 Mounts on rear fender. Fits most models 1973 thru 2003Softail®. SOLD EACH
11-302 Radius side mount. Fits 1986 & later Softail®.11-303 Horizontal side mount. Fits 1986 & later Softail®.11-304 Vertical side mount. Fits 1986 & later Softail®.8-285 Die cast, chrome plated diamond taillight only, with LED
illumination.
8-291 Replacement LED board for above part numbers.86-165 Replacement lens for above part numbers.
ALL PARTSCHROME PLATED
BILLET
11-301
11-303
B. CHROME LICENSE PLATE FRAMES WITHBOX LED TAILLIGHT
8-230 Plain, for fender mount for all models 1973 thru 2003.SOLD EACH
8-231 Skull, for fender mount for all models 1973 thru 2003.8-227 Skull, horizontal side mount for Softail®..8-292 Replacement LED board for above part numbers.
ALL PARTSCHROME PLATED
8-227
8-230
11-302
8-285
A
B
Fite 97’-05’ FLT, FLHT, FLTR and FLHR models. Can also be used forcustom use on any 3-hole license plate assembly.11-112 Chrome license plate mounting bracket. SOLD EACH
C. CHROME 3-HOLE LICENSE PLATE BRACKET
11-52 Outside dimensions 7-1⁄8” wide x 5-5⁄16” SOLD EACH
high. Holes measure center to center 5-9⁄16”wide x 2-5⁄8” high. Fits 4” x 7” license plate.
40-554 Chrome Horse® license plate frame SOLD AS KIT
screw kit with stainless steel buttonhead allens, washers, and nylon insert lock nuts.
D. EAGLE LICENSE PLATE FRAME
D
CHROMEPLATED
DIECAST
C
1/45
1A. CHROME BILLET MALTESE LED TAILLIGHT/LICENSE PLATE BRACKETS
Below mounts fit 7” x 4” license plates.8-274 Billet fender mount license / LED taillight. Fits most models
1973 thru 2003. Includes rubber mount block & hardware.8-275 Billet side mount radius, vertical license / LED taillight.
For 1986 & later Softail®.8-276 Billet side mount horizontal license / LED taillight.
For 1986 & later Softail®.8-277 Billet side mount vertical license / LED taillight.
For 1986 & later Softail®.8-293 Replacement LED board for above part numbers.
ALL PARTSCHROME PLATED
BILLET
8-2748-276
8-2758-277
B. CHROME BILLET CUSTOM LED TAILLIGHT /LICENSE PLATE BRACKETS
Below mounts fit 7” x 4” license plates.8-148 Billet side mount vertical license / LED taillight.
For 1986 thru 1999 Softail®. SOLD EACH
8-149 Billet side mount radius, vertical license / LED taillight.For 1986 thru 1999 Softail®.
8-354 Billet side mount vertical license / LED taillight. For 1986 thru 1999 Softail®. SOLD EACH
8-355 Billet side mount radius, vertical license / LED taillight.For 1986 thru 1999 Softail®.
8-154 Billet side mount horizontal license / LED taillight. For 1986 thru 1999 Softail®.
8-155 Billet license / LED taillight. Includes backing plate, rubber mount block & hardware.
8-290 Replacement LED board for above part numbers.86-164 Replacement lens for above part numbers.
8-148
8-154
8-149
8-155
A
B
8-354 8-355
ALL PARTSCHROME PLATED
BILLET
C. CURVED STYLE LICENSE PLATE HOLDERS
This license plate is made from billet aluminum and beautifullychrome plated. Comes with mounting hardware & base rubber mount.
11-309 4”x7” curved license plate assy., chrome. SOLD EACH
This license plate is a two peice assembly with a chrome alulminumouter surround, black steel backing plate & mounting hardware.
11-310 4”x7” curved license plate assy., chrome. SOLD EACH
C
11-309
11-310
1/46
1
Russell Performance’s three unique styles of license plate frames are madeof durable die cast zinc, featuring extra thick walls — an enduring qualitythat can be both seen and felt. Available in carefully plated, extra heavy,show chrome or double plated brass. There’s a Russell Performance licenseplate frame to enhance any motorcycle.
BORN IN THE U.S.A.: This distinctive chain design will enhance the appear-ance of any motorcycle. Patented.
TORNADO TWIST: Designed to appeal to today’s upscale motorcycle owners.
NEVADA NUGGET: A sophisticated design to set any motorcycle apart fromthe crowd. Patent pending.
BRASS CHROME DESCRIPTION
11-64 11-65 Born In The U.S.A. frame. SOLD EACH
11-68 11-69 Tornado Twist frame.
11-61 Nevada Nugget frame.
BORN INTHE U.S.A.
TORNADOTWIST
NEVADANUGGET
E. CUSTOM LICENSE PLATE FRAMES
Replacement bulb and harware kits for Arlen Ness license plate framesMW#11-110 & 11-111.
6-62 Replacement bulb. SOLD EACH
40-554 Chrome Horse® license plate frame SOLD AS KIT
screw kit with stainless steel button head allens, washers,and nylon insert lock nuts.
F. BULB & HARDWARE FOR NESS-TECH™LICENSE FRAMES
E
U.S.A. MADE light bar will allow mounting of up to 4 lights. U.S.A.MADE chrome back up plate included. SOLD EACH
11-28 8” x 4-1⁄2” license back-up plate. Also replace-ment plate for license plate frame part No. 11-35.
CHROMEPLATED
C. LICENSE PLATE FRAME & LIGHT BAR
A neat dress-up for the back of license, this chrome plated steel back-ing plated fits 7” x 4” plates.
11-97 Louvered backing plate. OEM 59899-88T. SOLD EACH
CHROMEPLATED
A. LOUVERED LICENSE BACKING PLATE
Features custom built-in lights with amber lenses that can be used ascustom turn signals or marker lights. Accepts 7.25” x 4.25” licenseplates.
11-122 Die cast, chrome plated aluminum SOLD EACH
license frame.6-62 Replacement bulb for above part No. 11-122.
CHROMEPLATED
B. DIE CAST LICENSE FRAME WITH LIGHTS
11-28
11-115 License plate frame with bolt kit. SOLD EACH
D. LICENSE FRAME FITS 7” X 4” LICENSE PLATES
CHROMEPLATED
A
B
C
D
1/47
1CHROMEPLATED “Electric” Kromets are great for license hold down bolts — gives extra
light to rear of bike. They can be used any place you may normally usethe standard kromets. Easy mounting with hollow mount stud forwiring. 12V.
41-971 “Electric” kromet. Red. SOLD EACH
41-972 “Electric” kromet. Amber.41-973 “Electric” kromet. Blue.
Traditional chrome plated decorative fasteners which can beused anywhere on the bike.41-284 Must buy package of twenty. SOLD AS PKG.
A. “ELECTRIC” KROMETS & CHROME KROMETS A
ELECTRIC
D
40-800 3-winged license plate bolts. SOLD AS PAIR
B. 3-WINGED LIGHTED LICENSE PLATE BOLTS
D. ARMATURES
Fits H-D® generators. Each set consists of one shunt & one regulat-ing coil. These coils feature high strength warp-free iron laminates,heat resistant, heavy gauge copper core wiring, wrapped woven clothinsulation (not paper), soldered field & ground terminals, and arematched paired for exact amperage values. SOLD EACH
53-283 Model 65A. 12V. U.S.A. MADE. OEM 30201-65.53-214 Model 65A. Imported. OEM 30201-65T.
Hard-to-find parts needed to rebuild generators for Harley-Davidsons®.
77-113 Fits No. 32E & 52 generators, 1936 SOLD AS KIT
thru 1957 Big Twins. American made.77-114 Fits Big Twin 1958 thru 1969 and Sportster®
1958 thru 1981.
77-11477-113Imported armature for H-D®.
53-152 For H-D® 65, 12 volt. OEM 30851-65TA. SOLD EACH
U.S.A. MADE armature for H-D®.53-215 For H-D® 65, 12 volt. OEM 30851-65A. SOLD EACH
C. SMALL PARTS & GASKET KITS FOR GENERATORS
E. FIELD COILS
E
B
C
1/48
1
C. U.S.A. MADE GENERATOR with BUILT-IN REGULATOR
Our top of the line 12 volt generator fits Big Twin, Sportster® & Servi-Car with 12V system. 5⁄16” Mounting screws. We also carry many ofthe repair & replacement parts for these generators.
70-117 Black generator. OEM 29975-65TA. SOLD EACH
70-121 Chrome generator. OEM 29976-83T. NO EXCHANGE NECESSARY
70-196 Black generator with finned built-in regulator.70-197 Chrome generator with finned built-in regulator.
A. MIDWEST’S GENERATORS
Top quality U.S.A. MADE 12V generator will accept Midwest or H-D® rebuild and replacement internal parts. This generator isbacked by a twelve month factory warranty.70-147 Black generator. Fits Big Twin 1958 thru SOLD EACH
1969, Sportster® 1965 thru 1981, and Servi-Car with 12Vsystem. Replaces OEM 29975-65A.
B. U.S.A. MADE GENERATOR
This U.S.A. MADE generator with built-in regulator will deliver moreamps when cold for faster recharging after starting. As the generatorheats up, current cuts back to extend generator life. This generator isbacked by a two year factory warranty.
70-148 Black generator. Fits Big Twin 1958 SOLD EACH
thru 1969, Sportster® 1965 thru 1981,and Servi-Car with 12V system.Replaces OEM 29975-65A.
70-117
70-196
70-197
A
B
C
D. GENERATOR END COVERHeavy gauge steel stamping, finest quality. Easy to install.
89-32 For Sportster® & 74 C.I. 1958 & later. OEM 31081-83T.SOLD EACH
CHROMEPLATED
D
89-10 For 74” & Sportster®, 1958 & later (generator equippedmodels). Easy to install. OEM 31080-83T. SOLD EACH
CHROMEPLATED
E. TWO BRUSH GENERATOR COVERE
1/49
1GENERATOR PARTSALL PARTS SOLD EACH EXCEPT AS NOTED
1 95-174 NEEDLE BEARING 74” 1961/1969 SPORTSTER® 1961/1981 (OEM 9064)
2 96-241 LOCKWASHER 1⁄4” (OEM 7036)
3 53-254 BLACK END COVER COMMUTATOR 65A MODEL GENERATOR (OEM 30132-61A)
53-324 CHROME END COVER COMMUTATOR 65A MODEL GENERATOR OEM 30132-61A)
4 95-103 OIL SEAL BRUSH END NEEDLE BEARING TYPE 74” 1961/1969, SPORTSTER® 1961/1976 SERVI-CAR 1961/1966 (OEM 12002)
5 53-185 BRUSH HOLDER 12 VOLT H-D® 65A GENERATOR (OEM 30350-65)
6 53-256 POLE SHOE SCREW (USE 2) 58 & 65A (OEM 30280-58)
7 53-144 BRUSHES 74” 1958 & LATER, XL, XLCH, SERVI-CAR U.S.A. MADE (OEM 30426-58) SOLD AS SET (2 BRUSH SET)
8 53-253 GENERATOR DRIVE END COVER 58 & 65A. ALUMINUM (OEM 30095-61)
9 95-102 OIL SEAL GEAR END 61” & 74” OHV 1946 & LATER FLATHEADS, & 45” (OEM 30145-46A)
10 95-101 BEARING GEAR END (OEM 9007) U.S.A. MADE
11 53-311 SNAP RING (OEM 11004) U.S.A. MADE
12 53-252 GEN. FRAME SCREW SPORTSTER® 1958/1980 74” 1958/1969 (OEM 30012-58)
13 53-193 DEFLECTOR 1958 & LATER (OEM 31035-58)
14 53-161 GEAR 14 TOOTH (OEM 31073-63A)
15 53-298 OIL SEPARATOR WASHER (OEM 31067-63)
16 53-146 BRUSHES ALL BIG TWINS 1953/1957 ACCUMAX (OEM 30425-51) SOLD AS SET (3 BRUSH SET)
53-144 BRUSHES 74” 1958 & LATER, XL, XLCH, SERVI-CAR U.S.A. MADE (OEM 30426-58) SOLD AS SET (2 BRUSH SET)
32
SEE PAGE 1-48FOR GENERATOR
1
SEE PAGE 1-47FOR ARMATURES
5
4
SEE PAGE 1-47FOR COILS
6
16
8
7
6
9
13
12
10
11
14
15
16
2
7
1/50
1Solid state 12V regulator hides inside of end cap. Great for custombikes where you don’t want a lot of stuff hanging off or you want totrash that old mechanical regulator.
53-421 Regulator; hides inside chrome end SOLD EACH
cover (included).53-601 Black finned generator end cap with regulator
& bearing.53-602 Chrome finned generator end cap with
regulator & bearing.
A. GENERATOR END REGULATOR
53-421
C. CHARGING SYSTEMKit includes chrome solid state voltage regulator, stator, rotor (yourchoice of heavy duty or late OEM style), and mounting hardware. Fits1970 thru 1999.
53-605 Kit with heavy duty rotor; 32 amp. SOLD AS KIT
53-606 Kit with late OEM style rotor; amp. SOLD AS KIT
53-55 Kit with 38 amp components. SOLD AS KIT
53-630 Rotor spacer, small. OEM 29961-85. SOLD EACH
53-631 Rotor spacer, large. OEM 29960-85. SOLD EACH
B. ROTORSThese rotors have enclosed magnets; no chance that they can comeloose. Fits Big Twin 1981 & later. Replaces OEM 29957-81B & 29957-85A. Rotors will work on all H-D® Big Twin with correctly matchedstator and volt pak. Refer to service manual for proper spacing due todifferent sprocket shaft lengths and compensator stack heights.
53-603 Heavy duty rotor; 22/32 amp. SOLD EACH
15/32” Thick at splines. “No tear out.”53-604 Late OEM style rotor; 22-32 amp. .195” Thick at
splines. Supplied with two washer spacers:OEM 29961-85 (1.75” O.D. x .093” thick) andOEM 29960-85 (2.81” O.D x .219” thick).
53-52 Rotor; 38 amp. OEM 29981-95.
53-602
Generator mounting screws to mount H-D® or Midwest generators.Authentic reproductions. Perfect for restorers or rebuilders.
53-195 For Big Twin 1936 thru 1957. SOLD AS SET
53-194 For Big Twin 1958 thru 1969.53-240 For H-D® 45” 1937 thru 1951.53-241 For H-D® 45” 1958 thru 1973.
SEE SECTION 14 FOR ALLEN TYPE SCREWS
HIGH QUALITYCHROME PLATED
D. GENERATOR SCREW KITS
53-603
53-605
53-601
53-606
53-631
53-630
53-55
A
B
C
D
1/51
1Accel’s 6V & 12V generator overhaul kit is blister packaged to show offthe top notch parts that are included: Accel’s famous brush sets, a spe-cial double lip oil seal (guards against oil leakage into the generator),and a UL approved fiber generator cover gasket impregnated withchemical solids to maintain a seal under extreme conditions.
PART GENERATORNO. VOLTAGE MODEL YEAR MODEL
12V #65 1965/1982 XL, FL series.77-159 6V #58 1958/1960 XL, XLH, XLCH,
FL, FLH.6V #61 1961/1964 XL, XLH, XLCH.
SOLD AS KIT
A. GENERATOR OVERHAUL KIT
A
53-296 Fits all Big Twins 1971 & later. SOLD EACH
OEM 29954-71.PLASTIC
B. ALTERNATOR PLUG RETAINER
B
D. STATOR & ROTOR53-676 32 Amp rotor / stator kit, includes SOLD AS KIT
rotor kit OEM 29957-81B & stator OEM 29970-88.53-677 32 Amp stator, replaces OEM 29970-88. SOLD EACH
Fits 1989 thru 1999 Big Twin.53-678 32 amp rotor kit. Replaces SOLD AS KIT
OEM 29957-81B. Fits 1976 thru 1999 models.53-679 38 Amp 3 phase rotor / stator kit. Charges 15 SOLD AS KIT
amps at 800 RPM. Includes rotor kit OEM 29981-95 & stator OEM 30017-01.
53-680 38 amp 3 phase stator, replaces OEM 30017-01. SOLD EACH
Fits 2001 thru 2004 Softail® & 2004 Dyna®.53-681 38 Amp rotor kit, replaces OEM 29981-95. SOLD AS KIT
Fits 2000 & later models with 3 phase 38 amp system.
D
C
Attached direct to the engine case to ensure that your plug stays inplace and helps prevent any unwanted electrical shorts.53-129 Chrome alternator plug retainer, fits Big Twins 70’-88’.53-130 Chrome alternator plug retainer,
fits Big Twins 89’-present. SOLD EACH
C. CHROME ALULMINUM ALTERNATOR PLUG RETAINER
1/52
1
Leaders in New Technology™Leaders in New Technology™Leaders in New Technology™Leaders in New Technology™
C. VOLTAGE REGULATORS FOR BIG TWIN 1970& LATER AND LATE SPORTSTER®
The Series style replacements’ voltage output is calibrated formaintenance free batteries. The series circuitry opens chargingsystem when battery is fully charged, resulting in cooler statoroperation and extended system life. Chrome billet case. Bolt-onreplacement. SOLD EACH
53-577 For 22 amp Big Twin 1981 thru 1988.53-579 For 15 amp Big Twin 1970 thru 1975.
C
BIG TWIN53-186 Fits 1970 thru 1975 H-D® 74” 4 Wire, SOLD EACH
15 amp. OEM 29965-70.53-128 Fits 1976 thru 1980 H-D® 74” & 80”. 2 Wire,
17.8 amp. OEM 29965-75.53-251 Fits 1981 thru 1988 H-D® 80” 2 Wire, 22 amp.
OEM 29965-81.53-319 Fits all models 1989 thru 1999 H-D® 80”.
32 Amp. OEM 29970-88. Will also work on earlier modelswhen equipped with high output 32 amp alternator kit.
53-54 38 Amp. Replaces OEM 30017-01.
SPORTSTER®53-300 Fits Sportster® 883cc, 1100cc and SOLD EACH
1200cc, 1986 thru 1990. 19 Amp. OEM 29967-84A.53-320 Fits Sportster® 883cc & 1200cc, 1991 & later.
22 Amp. OEM 29967-89.
53-216 Stator locking kit; fits all Big Twins 1970 thru 1986. SOLD AS KIT
41-469 Stator screw kit. SOLD AS KIT
53-128
A. STATORS
U.S.A. MADE STATORSThese OEM quality U.S.A. MADE stators are covered by a limited oneyear warranty. Molded or unmolded versions available where listed.The quality you expect with a budget price. Just like stock.
ACCEL “LECTRIC” STATORSU.S.A. MADE from the finest components available, these high qualitystators are backed by a lifetime replacement warranty on all eight partnumbers which cover all H-D® twins from 1970 & later. Each stator isindividually wrapped and packaged in an attractive four color displaybox. See page 1-46 for stainless steel screw kit.
B. U.S.A. MADE STATORS
U.S.A. MADE ACCEL OEMPART NO. PART NO. NO. YEAR MODEL STYLE
BIG TWIN
53-607 53-339 29965-70 1970 / 1975 Big Twin Unmolded
53-608 53-340 29965-75 1976 / 1980 Big Twin Molded
53-609 53-341 29965-81 1981 / 1988 Big Twin Molded
53-610 53-342 29965-81A 1981 / 1988 Big Twin Unmolded
53-613 53-345 29970-88A 1989 & Later Big Twin Unmolded
SPORTSTER
53-611 53-343 29967-84A 1985 / 1990 XL Unmolded
53-612 53-344 29967-84 1985 / 1990 XL Molded
53-614 53-346 29967-89 1991 & Later XL Unmolded
SOLD EACH
A
B
1/53
1U.S.A. MADE SOLID STATE ELECTRONIC VOLTAGE REGULATORSThese quality manufactured solid state voltage regulators cover the popu-lar H-D® applications. Highly reliable; the ceramic & circuit board tech-nology gives a combination of improved electrical regulation with lowertemperatures. Available chrome plated or black with polished fins. 30 Daywarranty.
ACCELH-D® owners & mechanics will welcome Accel’s solid state voltage regu-lators that cover every H-D® application. Each regulator is designed toperform with high reliability and features Accel’s exclusive chrome finishfor that custom look. All units are set to factory OEM specifications.Accel’s unique circuitry ensures that the battery cannot be drained by thecharging system while the bike is not in use. Each unit comes completewith installation instructions. Limited life time warranty.
ARLEN NESSAccel & Arlen have teamed up to offer the ultimate in custom styling andAmerican made quality & performance. Starting with the first in a seriesof products…the Arlen Ness Signature Edition voltage regulators have aunique design, are show chrome plated, assembled with Accel’s lateststate-of-the-art electronic circuitry and bolt on like the stock unit.
NOWCHROME!
CHROMEPLATED
AC
CE
L E
LEC
TR
ON
IC V
OLT
AG
ER
EG
ULA
TOR
S —
CH
RO
ME
AR
LEN
NE
SS S
IGN
ATU
RE
VO
LTA
GE
RE
GU
LATO
RS
CH
RO
ME
PLA
TED
U.S
.A.
MA
DE
RE
GU
LATO
RS
BLA
CK U
.S.A
. MA
DE
RE
GU
LATO
RS
CON
NE
CTO
R T
YPE
A B C D
E F G
CONNECTOR
TYPES
SOLID STATE ELECTRONIC VOLTAGE REGULATORS
BLACK
CHROMEPLATED
H
APPLICATION YEAR OEM NO. CHARGING SYSTEM
FL & FLH. 1958/1964 74510-59 Replaces6V mechanical H 53-305 —
XL, XLH & XLCH. 1958/1964 74510-47A regulator for 6V generator.
FL & FLH. 1965/1969 74511-65 Replaces 12V mechanical H 53-552 53-306 53-222 —
XL, XLH & XLCH. 1965/1977 74510-64 regulator or 12V generator.
FL & FLH. 1970/1975 74510-70A 15 Amp alternator. A 53-547 53-302 53-262 —
FX & FXE. 1971/1975
FL, FLH, FLH-80, FLT & Classic 1976/1980 74512-79A 17.8 Amp alternator B 53-548 53-303 53-219 —
FX, FXE, FXS, FXS-80 & FXEF-80. 1976/1980
XLCH. 1977 74504-78 12V Generator E 53-549 53-304 53-220
XLH, XLCH & XLS. 1978/1981
FLH 80 & Classic. 1981/1984 74516-86 22 Amp alternator. D 53-550 53-309 53-264 —
FX, FXE, FXEF, FXS & FXB. 1981/1985
FXWG. 1981/1986
FLT & FLHT Classic 1981/1988
FXR, FXRS, FXRT & FXRP. 1982/1988
Softail® models. 1986/1988
XL, XLS & XLX. 1982/1984 74504-82 12V Generator. F 53-551 53-308 53-263 —
XL. Late 1986/ 74523-84A 19 Amp alternator. G 53-553 53-310 53-290 ––
1990
All Big Twin models. 1989 & Later 74519-88 32 Amp alternator. C 53-544 53-543 53-322 53-335
XL. 1991/1993 74523-91 22 Amp alternator. G 53-542 53-541 53-362 ––
XL 883 / 1200. 1994 & Later 74523-94A 53-546 53-545
SOLD EACH
1/54
1 MIDWEST’S POWERPAKS
U.S.A. MADE POWERPAKS, solid state voltage control units, significantly & economically upgrade the electrical system of motorcy-cles. They exceed all factory design specifications, delivering improved electrical performance for lighting, battery charging & igni-tion while preventing damage to all power sources (generators, alternators, flywheel magnetos, etc.) and wiring systems. Lightsdeliver increased brilliance, last longer, and normally stop flickering. Batteries are kept at precise charging levels and will not boilover or go “flat.” Exact voltage control for other systems, particularly ignition, results in easier starting, increased performance andelimination of high speed miss due to faulty current control. Many motorcycles can be converted to batteryless (battery elimination)mode for special applications when these Powerpaks are used in conjunction with our part No. 53-125 capacitor. Among the mostadvanced & reliable voltage control units available, they are impervious to heat, cold, vibration, shock, moisture, oil, dust, dirt, & vir-tually all common elements. There are no moving parts and they never require adjustment or maintenance. Easily & compatiblyinstalled to stock wiring. Eliminate unreliable stock regulators, rectifiers, relays, zenor diodes, capacitors, ballast resistors, & induc-tors with our POWERPAKS.
ONE YEAR WARRANTY: All warranteed solid state electronics are guaranteed against any manufacturing defects for one yearfrom the date of purchase. Each unit is warranteed against normal use failure from moisture, corrosion, engine vibration, ambientheat and cold when properly installed. MIDWEST waives responsibility for failure of faulty OEM, aftermarket or other replacementelectrical parts (lights, fuses, wiring shorts, etc.). All warranty claims must be processed through our MIDWEST customer servicedepartment. All warranty claims must be accompanied by MIDWEST invoice number and purchase date.
A B C
CONNECTOR TYPES
H-D® WITH 2-BRUSH GENERATORFor all Sportsters® 1978 & earlier and H-D® 74” with 2-brush genera-tor, this unit provides superior performance & reliability comparedwith old mechanical and points-type units (Delco, Bosch, etc.).Eliminates electrical failures & battery charging problems. Easy start-ing, full lighting & ignition in batteryless operation on magnetoequipped bikes if used with our part No. 53-125 capacitor. NO PLUG (3bare wires).
53-26 Replaces all 12V mechanical regulators. SOLD EACH
ALL FL, FLH, & FX, 1970 THRU 1975This unit vastly increases electrical performance for lighting, batterycharging, & ignition. Eliminates electrical output problems commonwith standard control units. Plugs into the stock output lead & offersbatteryless lighting & ignition when used with our part No. 53-125capacitor. Installs easily with 4 hole female plug & 1 bare wire. PLUGTYPE: B.
53-31 For FL, FLH & FX, 1970 thru 1975. SOLD EACH
H-D® FL, FLH, & FX, 1976 THRU 1980This unit greatly upgrades the performance & reliability of the currentoutput for lighting, battery & ignition. Replaces stock voltage controlunits and mounts quickly & cleanly to custom bracket part No. 5-68.Offers batteryless lighting & ignition when used with part No. 53-125capacitor. Installs easily with 2 hole female plug & 3 bare wires. PLUGTYPE: C.
53-35 For FL, FLH & FX, 1976 thru 1980. SOLD EACH
BIG TWIN 1981 THRU 1988 WITH 24 AMP ALTERNATORThis unit provides vastly improved control for voltage regula-tion & battery charging current. Specially designed for the lat-est 24 amp high-output alternator. May be used for battery-less operation when used with our part No. 53-125 capacitor.Installs easily with 2-plug male lead. PLUG TYPE: A.
53-212 For FLH 80, Classic, FLT, FLHT Classic, SOLD EACH
FX, FXE, FXEF, FXS, FXB, FXST, FXSTC, FLSTC, FXR, FXRS, FXRT, FXRP & FXWG.
53-47 Economy model. Fits same applications as abovepart No. 53-212. Excellent Japanese quality.
SOFTAIL® 2001 & LATERThis unit is 38 amp, chrome. Replaces OEM 74610-01 & 74540-01 (imported). PLUG NOT SHOWN.
53-53 For Softail® 2001 & later. SOLD EACH
53-53
1/55
1
B. BATTERYLESS STARTING BOOSTER CAPACITOR
This capacitor voltage storage unit greatly increases spark voltage atstarting RPM when using batteryless operation with a voltage regulator/ rectifier, such as our Powerpaks. Filters current surges to protect sen-sitive electronic ignition components and reduces low speed light flick-ering. For all alternator / generator systems with the battery eliminat-ed. Compatible for use with our Powerpaks.
53-125 Capacitor. SOLD EACH
A. POWERPAKS FOR IMPORTED MOTORCYCLES
D. REGULATOR / RECTIFIER CUSTOM MOUNTING BRACKET
For all 3-phase, permanent magnet alternators, this unit precisely regu-lates A.C. output voltage and rectifies exact D.C. charging current.Replaces all stock voltage control units and offers a optional battery-less lighting & ignition operation when used with our part No. 53-125capacitor.
For all single-phase, permanent magnet alternators, this unit precisely reg-ulates A.C. output voltage and rectifies exact D.C. charging current. Installseasily with 3 bare wires. Offers optional batteryless lighting & ignitionoperation when used with our part No. 53-125 capacitor.
For: BENELLI: All 250 Twins. BRITISH (Lucas): All 1962 & later BSA,TRIUMPH, NORTON, etc. HONDA: All 4-cycle singles & all 1979 &later Twins. KAWASAKI: All 4-cycle Twins, H-2 Triple & early 550/late650 Fours. LAVERDA: All 1200/1000 Triples & all 500 Twins. YAMAHA:SR-250.
53-34 For above applications. SOLD EACH
This custom mounting bracket is made from rugged stainless steel andgiven a brushed finish. Bolts to the bottom front motor mount of all 74”& 80” or fits readily to most other motorcycles. Accepts all ourPowerpaks.
5-68 Bracket. SOLD EACH
ONE YEARWARRANTY
E. HEAVY DUTY POWERPAK MOUNTThis one won’t split apart — 5mm (.1970”) thick chrome plated steel.Bolts to the bottom of front motor mount on Big Twin. 5/16 - 18 Studsfor easy mounting of powerpak.
5-233 Heavy duty powerpak mount bracket.SOLD EACH
CHROMEPLATED
OVER 3/16”THICK
C. VOLT PAK MOUNT FOR ULTIMA® MOTORSDESIGNED BY EASTON CUSTOMS
Mounts volt pak in the traditional spot off front motor mount bolts.Mount is threaded and bolt comes in from the bottom giving a niceclean look. Volt Pak sets at approx. 45˚ angle for max air flow acrossfins. The stock motor case mounted oil filter will not work. Designedfor Ultima® motors will work on stock motors as well.5-260 Volt Pak mount SOLD EACH
A
B
C
D
E
1/56
1
89-381 Cover fits most voltpaks. SOLD EACH
CHROMEPLATED
D. CHROME PLATED FINNED VOLTPAK COVER
Can be used on any 12 volt application. OEM 74511-65.
53-23 For XLCH 1965 and later and XLH SOLD EACH
1965 & 1966.
53-274
53-269
53-275
This high quality U.S.A. MADE regulator will directly mount to thegenerator end cap. NOTE: Because of the 15° angle difference betweenBig Twin and Sportster®, you must order part No. 70-150 below whenusing on Big Twin. This will enable the fins to line up with the motor.
70-149 Generator end regulator. Fits H-D® SOLD EACH
No. 29975-65A generators on Big Twin 1965thru 1969 and Sportster® 1965 thru 1981.
70-150 End plate.
B. BOSCH VOLTAGE REGULATOR
C. U.S.A. MADE GENERATOR END REGULATOR
A. 6 & 12 VOLT VOLTAGE REGULATORS for H-D®
Heavy duty shock mounted steel bases. Vibration resistant internal wire connections.OEM style covers now with your choice of chrome plated or hard gloss black finishes.Fiber and mylar insulating pads. Large diameter contact surfaces. U.S.A. MADE.
CHROME BLACKPART NO. PART NO. OEM NO. YEAR MODEL / APPLICATION
12 VOLT53-274 53-165 74510-64 1965/1969 FL, FLH.
1965/1977 XLH.
ELECTRO-MECHANICAL VOLTAGE REGULATOR (BOSCH TYPE)53-269 53-268 74511-65 1965 & 1966 XLH.
1965/1977 XLCH.
6 VOLT53-275 –– 74510-47A 1952/1964 All “K” Model Twins, XL,
1958/1964 FL, FLH Twins.
ALL PARTS SOLD EACH
A
B
C
D
E. REGULATOR (BOSCH) MOUNTINGBRACKET
Used for Bosch regulator (part No. 53-23) or Bosch type regulator. Putthe regulator where it belongs, on top of the generator. Mount to gen-erator frame screw. Allows you to use stock end cover.
5-69 For Sportster® and H-D® 74”. SOLD EACH
CHROMEPLATED
E
1/57
Exact reproduction for all H-D® rubber mounted motors.
5-126 Fits Shovel® 1980 thru 1985 and FLT & FXR 1984 & later.OEM 74529-79. SOLD EACH
89-1 For Prestolite starter motor on FL 4 SOLD EACH
speed (except Classic) 1966 thru 1982, andXLH 1967 thru 1980. OEM 31350-83T.
89-92 For Hitachi starter motor on FX 4 speed 1974 thru 1986,and XLH 1974 thru early 1976.OEM 31351-83T.
89-280 For all 5 speeds 1980 thru 1988. OEM 31507-87T.
89-34 Fits 1968 & later starter motors only. SOLD EACH
For use on H-D® 74”, 80” and Sportster®.OEM 31565-67.
CHROMEPLATED
Oblong, use with large Delco Remy regulators and 2 brush generators.
89-4 Large Delco Remy regulator cover. SOLD EACH
This rectifier mounting bracket fits OEM and accessory rectifiers.
5-85 For FL & FX, 1976 & later. SOLD EACH
OEM 74533-75B.
89-1
89-92
89-280
ALL PARTSCHROME PLATED
CHROMEPLATED
Chrome relay cover fits all FL 1965 thru 1984. OEM 66425-68.
89-282 Relay cover. SOLD EACH
CHROMEPLATED
C. RECTIFIER MOUNTING BRACKET for BIG TWIN
E. STARTER COVERS
B. LARGE REGULATOR COVER
D. RECTIFIER/REGULATOR BRACKET
F. STARTER RELAY COVER
G. STARTER MOTOR END COVER
89-525 Cover kit for 1989 thru 1999 Softail®. OEM 74578-97.89-526 Cover kit for 1991 & later Dyna®. OEM 74577-97.89-527 Cover kit for 1985 & later XL (shown). OEM 74579-97.89-537 Cover kit for 2001-2006 Softail®. OEM 74597-01.
SOLD AS KIT
A. REGULATOR COVERS
A
B
D
G
E
F
CHROMEPLATED
CHROMEPLATED
1
1/58
1REPLACES
PART NO. OEM NO. YEAR MODEL
53-284 Accel, chrome 71469-65B 1967/1978 XLH, XLCR & XLT.
53-285 Accel, zinc. 1979 & 1980 XL models.
53-456 Midwest brand, zinc finish, 1965/1984 FL & FLH (except FLT).
(best buy) 1971/1985 FXE, FXEF & FXS1979/1985 FXE-80, FXEF-80 & FX-80
1980/1985 FXB.
1984/1988 FXST
1983/1985 FXSB.
1985 & 1986 FXWG.
53-286 Accel, chrome 31489-79B 1980/1988 FLT.
53-457 Midwest brand, 1984/1988 FLT Classic.
zinc finish, (best buy) 1982/1988 FXR.
1984/1988 FXRP.
1984/1988 FXRP.
SOLD EACH
U.S.A. MADE repair kit for H-D-® solenoids OEM 71465-85T, 71469-65and 31489-79B.
53-288 SOLD AS KIT
A. REPLACEMENT SOLENOIDS
B. SOLENOID REPAIR KIT
Available in standard or stronger versions, each set is complete withepoxy/cloth-wrapped coils with long-life sintered metal brushes.Features include five turns of solid copper ribbon which yield up to20% more torque for faster starting for stock & modified H-D®engines. Replaces OEM 31540-66.
Fits FL FLH & FLH-80, 1966 thru 1982, FLT Classic 1980 thru 1983, FXR& FXRS, 1982 thru early 1983, XLH 1967 thru 1978, and XL & XLS 1979 &1980. (Prestolite.)
53-278 Stronger starter field coils. SOLD AS SET
E. STARTER FIELD COILS
53-293 Fits Sportster® 1967 thru 1980 SOLD EACH
OEM 31424-67.53-294 Fits Big Twin 1965 thru 1980. OEM 31445-65A.
53-293 53-294
H. BENDIX STARTER GEAR SHIFT LEVERS
U.S.A. MADE Bendix 5 roller starter gear. For 1965 thru 1988.Replaces OEM 31443-65.
53-157 Midwest brand (best buy). SOLD EACH
53-367 Accel.
70-111 Fits FL 1970 thru 1982, FX 1971 thru SOLD EACH
1984, FXWG 1980 thru 1983, chain drive4 speed models. OEM 31482-70.
F. STARTER SHAFT
G. STARTER GEAR
Complete starter jackshaft assembly;including coupler, springand all necessary clips. SOLD AS ASSY
70-181 Fits Big Twin 1989 thru 1993, 9 tooth.70-182 Fits Big Twin 1994 & later, 10 tooth.
I. STARTER JACKSHAFT ASSEMBLIES
70-184 Fits Big Twin 1991 & later.OEM 31604-91. SOLD AS KIT
C. STARTER SOLENOID REPAIR KIT
Fits all models 1991 & later except V-Rod®.
89-8 Chrome cover. Replaces OEM 31783-00 SOLD EACH
& 31688-90.
D. SOLENOID COVERCHROMEPLATED
A
B
C
D
E
F
GH
I
1/59
1
BELT DRIVE BIG TWIN 4 SPEED 1982 & LATER
��������������������
��������������������
SEE PAGE 1-59 FOR STARTER DRIVE GEAR
2
1
4
3
6
SEE PAGE 1-59 FOR STARTERDRIVE GEAR
3
SEE PAGE 1-59 FOR STARTERDRIVE GEAR
3
2
1
9
8
5
SPORTSTER® 1967 THRU 1980
BIG TWIN 1965 THRU 1982
7
7
7
1 95-413 THRUST WASHER FL & FX 1965/1985 (OEM 31502-65) SOLD AS PAIR
2 95-226 NEEDLE BEARING (OEM 9063)
3 96-310 RET. RING (OEM 11039) U.S.A. MADE
4 78-155 GASKET FL, FLH & FX, 1965/1982 (OEM 60559-80)
5 70-111 STARTER SHAFT FL 1970/1982 FX 1971/1983 EXCEPT FXB & FXSB (OEM 31482-70)
6 53-295 OIL DEFLECTOR PLATE 1965/1982 (OEM 60516-65A)
7 95-598 STARTER SHAFT BEARING TORRINGTON (OEM 9062)
8 70-109 STARTER HOUSING PRESTOLITE TYPE STARTER. 1965/E. 1979. (OEM 31465-65)
70-110 STARTER HOUSING HITACHI TYPE STARTER 1973/E. 1979. (OEM 31572-73)
9 96-241 LOCKWASHER (OEM 7036)
STARTER DRIVE PARTSSOLD EACH EXCEPT AS NOTED — ALL PARTS MEET OR OR EXCEED OEM SPECIFICATIONS
1/60
1
1.4 KW Series
ULTIMA THUNDER FIRE™HEAVY DUTY STARTERS 89’-06’
Ultima is setting the standard in Starter performance and value with the new HeavyDuty series Thunder Fire starters for 1989 thru 2006 model Big Twins, except 2006Dynas. These Starters are built with all new tooling and all parts are new not Re-man-ufactured like some of our competitors. We have made improvements to the key com-ponents in these starters to insure long life and exceptional performance. We are sureyou will agree these are a best value product.
1.4 KW SERIES• Availible in Black or Chrome• Fits all 89/05 model Big Twins with no clearance issues• Works with OEM battery• Each Starter is individually tested with data sheet included
1.75KW SERIES• Great upgrade for stock and 1.4 Kw starters. Made for trouble free starting
of most small strokers • Fits some stock applications on Big Twins where 3/4” longer body
is not a problem. • Includes manual push button cap on solenoid• Works with OEM battery• Each Starter is individually tested with data sheet included
2.0 KW SERIES• Made for Big Inch engines• Heavier Clutch Gears• Fits some stock applications on Big Twins where 7/8” longer body
is not a problem. • Fits FLT and Dyna when used with 70-230 oil filler spacer • Includes manual push button cap on solenoid• Requires a 300 amp Battery and good cables for best results• Each Starter is individually tested with data sheet included
2.4 KW SERIES• Made to Start anything Big Inch• Heavier Clutch Gears• Includes manual push button cap on solenoid• Requires a 300 Amp Battery and good cables for best results• Each Starter is individually tested with data sheet included
TOP POST STARTERS ANGLED POST STARTERS
70-220 1.4 Kw Chrome Plated 70-222 1.4Kw Chrome Plated70-221 1.4 Kw Wrinkle Black 70-223 1.4Kw Wrinkle Black70-224 1.75 Kw Chrome Plated 70-225 1.75 Kw Chrome Plated70-226 2.0 Kw Chrome Plated 70-227 2.0 Kw Chrome Plated70-228 2.4 Kw Chrome Plated 70-229 2.4 Kw Chrome Plated
1.75 KW Series
2.0 KW Series 2.4 KW Series
Angled Post
Top PostBlack Wrinkle finish
STARTER BOLTS70-218 Starter Bolt; 1/4”-20 x 5-1/4”70-219 Starter Bolt; 1032” x 6”
ULTIMA THUNDER FIRE™ HEAVY DUTY STARTERS06’ & LATER DYNAS, 07’ & LATER BIG TWINS
Ultima has continued the standard in Starter performance and valuewith the new Heavy Duty series Thunder Fire starters for 2007 & latermodel Softail & Touring models, and 2006 & later Dyna. TheseStarters are built with all new parts & tooling. Not Re-manufacturedlike some of our competitors. Works with OEM battery & individuallytested w/data sheet included. We are sure you will agree these are abest value product.
1.4 KW SERIES★70-235 1.4 Kw, Thunder FireTM starter, wrinkle black.★70-236 1.4 Kw, Thunder FireTM starter, chrome plated.★70-237 1.4 Kw, Thunder FireTM starter, plain.
1.75 KW SERIES★70-238 1.75 Kw, Thunder FireTM starter, wrinkle black.★70-239 1.75 Kw, Thunder FireTM starter, chrome plated.★70-240 1.75 Kw, Thunder FireTM starter, plain.
1/61
Item Part Number Description Number1 Connector 70-2012 Electro-magnetic Switch Assembly and Housing (Angled Post), Chrome, includes # 1,20,28 70-204
Electro-magnetic Switch Assembly and Housing (Angled Post), Black, includes # 1,20,28 70-203Electro-magnetic Switch Assembly and Housing (Top Post), includes # 1,20,28 70-266
3 Starter Seal/Gasket Kit 70-2124 Yoke Assembly, Includes Internals plus 2 Brushes and Connector (for 1.4KW Starter), Chrome 70-213
Yoke Assembly, Includes Internals plus 2 Brushes and Connector (for 1.4KW Starter), Black 70-207Yoke Assembly, Includes Internals plus 2 Brushes and Connector (for 1.75KW Starter), Chrome 70-214
5 Insulating Boot 70-2156 Bearing, Armature, 6002 Series 70-2177 Armature Assembly (for 1.4KW Starter), includes # 6,8 70-205
Armature Assembly (for 1.75KW Starter), includes # 6,8 70-2068 Bearing, Armature, 608 Series 70-2679 Spring, Brush - Includes 2 springs 70-26810 Brush Plate Assembly, Includes 2 Brushes and 2 Springs 70-20811 Starter End Cap, Chrome 70-269
Starter End Cap, Black 70-26312 Fastener Kit, Brush Plate (2 Screws), Chrome 70-270
Fastener Kit, Brush Plate (2 Screws), Black 70-26413 Fastener Kit, Starter Housing (2 Screws), Chrome 70-271
Fastener Kit, Starter Housing (2 Screws), Black 70-26514 Steel Ball 70-27215 Spring 70-27316 Plunger Assembly 70-25017 Solenoid Cover Assembly (for 1.4KW Starter), Chrome 70-251
Solenoid Cover Assembly (for 1.4KW Starter), Black 70-261Solenoid Cover Assembly w/push button (for 1.75KW Starter) 70-274
18 Idler Gear 70-25219 Bearing and Shaft Assembly, Idler Gear 70-25320 Starter Post Assembly, Main Power (long post) 70-25421 Fastener Kit, Starter Housing (2 Screws) 70-25522 Face Plate, Starter Housing, Chrome 70-256
Face Plate, Starter Housing, Black 70-26223 Bearing, Clutch, 6004 Series 70-25724 Clutch Assembly, Starter, includes # 23,25 70-21125 Bearing, Clutch, 6904 Series 70-25826 Spring 70-25927 Output Shaft, Starter 70-26028 Starter Post Assembly, Solenoid to Starter Motor (short post) 70-283
ULTIMA 1.4 & 1.75 KW THUNDERFIRE STARTERS 1
1/62
1
Item Part Number Description Number1 Electro-magnetic Switch Assembly and Housing (Angled Post), includes # 2,11,27 70-275
Electro-magnetic Switch Assembly and Housing (Top Post), includes # 2,11,27 70-2852 Connector 70-2763 Starter Seal/Gasket Kit 70-2774 Spring, Brush - Includes 2 springs 70-2785 Brush Plate Assembly, Includes 2 Brushes and 2 Springs 70-2796 Bearing, Armature, 6200 Series 70-2807 Armature Assembly (for 2.0KW Starter), includes # 6,8 70-281
Armature Assembly (for 2.4KW Starter), includes # 6,8 70-2828 Bearing, Armature, 608 Series 70-2679 Yoke Nut-Pin (2 Nut-Pins) 70-28410 Yoke Assembly, Includes Internals plus 2 Brushes and # 9 (for 2.0KW Starter) 70-286
Yoke Assembly, Includes Internals plus 2 Brushes and # 9 (for 2.4KW Starter) 70-28711 Starter Post Assembly, Main Power (long post) 70-28812 Steel Ball 70-27213 Spring 70-27314 Plunger Assembly 70-28915 Insulating Boot 70-29116 Solenoid Cover Assembly, w/Push Button 70-29217 Fastener Kit, Starter Housing (2 Screws) 70-29318 Fastener Kit, Starter Housing (2 Screws, 2 Washers) 70-29419 Drive Gear, Armature 70-29520 Idler Gear 70-29621 Bearing and Shaft Assembly 70-29722 Face Plate, Starter Housing 70-29823 Bearing, Clutch, 6004 Series 70-25724 Clutch Assembly 70-24725 Spring 70-24826 Output Shaft, Starter 70-24927 Starter Post Assembly, Solenoid to Starter (short post) 70-300
ULTIMA 2.0 & 2.4 KW THUNDERFIRE STARTERS
1/63
1ULTIMA THUNDER FIRE™HEAVY DUTY STARTERS
FOR 1965 THRU 1986 MODEL BIG TWINS
Our Starters are designed to replace the obsolete designs of thePrestolite and Hitachi starters used on 1965 thru 1986 model BigTwins. Based on all new tooling some of these models will offerover two times as much cranking power over their olderdesigned counterparts. These starters boast a 1.4 + KW ratingand will turn over Stockers and Strokers with ease. These are ahighly recommended upgrade for older models.
70-231 1980/1985 FLT, FLHT, FXR models rubber mounted engine, 5 speed transmission and exposed rear chain.
70-230 All Big Twin models 1986 thru 1988.70-232 1979/Early '84 models with 4 speed
transmission and rear chain drive.70-233 All Big Twin models 1967/ Early 1979
with solid mount engine.
70-230
70-231
70-232
70-233
These starters boast a 1.4 + KW rating and will turnover Stockers and Strokers with ease. These are ahighly recommended upgrade for 1981 thru 2007Sportster® models.
70-234 1981 / 2007 Sportster® models.
THUNDER FIRE® HEAVY DUTY STARTERSFOR 1981/ LATER SPORTSTERS®
70-234
1/64
1Fits FL 1966 thru 1981, FLT 1980 thru 1982, FXR 1982, XL 1967 thru 1973,and XL 1977 thru 1980.
A fine restoration item, this reproduction of the H-D® OEM Prestoliteelectric starter motor is available in chrome or black. We also offermany of the replacements parts for this starter motor.
70-130 Complete black starter motor assembly. OEM 31458-66A.SOLD EACH
70-131 Complete chrome starter motor assembly. SOLD EACH
OEM 31458-66A & 31463-88T.
B. REPLACEMENT PARTS FOR PRESTOLITE-TYPE STARTER MOTORS
A
70-140 Chrome commutator end cover with bushing. SOLD EACH
OEM 31578-73.70-141 Armature. Includes bearing for above SOLD EACH
starter motors. OEM 31580-73.70-142 4-Brush set for above starter motors. SOLD AS SET
OEM 31582-73.70-143 Complete brush holder assembly. OEM 31581-73. SOLD EACH
70-144 Drive gear end ball bearing. OEM 31583-73. SOLD EACH
70-145 Thru-bolt kit. OEM 31576-73. SOLD AS KIT
14-26 Battery and Hitachi starter motor SOLD EACH
bracket. Fits FXE 1973 thru 1984. Chrome plated.
D. REPLACEMENT PARTS FOR HITACHI-TYPESTARTER MOTORS
C
14-27CHROMEPLATED
70-141
A. ULTIMA THUNDER FIRE™ PRESTOLITE-TYPESTARTER MOTORS
70-132 Chrome commutator end cover with SOLD EACH
bushing. OEM 31536-66.70-133 Armature for above starter motors. SOLD EACH
OEM 31542-66.70-134 4-Brush set for above starter motors. SOLD AS SET
OEM 31541-66.70-135 Complete brush holder assembly. OEM 31537-66. SOLD EACH
70-137 Thru-bolt kit. OEM 31535-66. SOLD AS KIT
14-27 Prestolite starter motor bracket. Fits SOLD EACH
FL models late 1966 thru 1982 and Classic 1979 thru 1981.Replaces OEM 31476-66. Chrome plated.
C. ULTIMA THUNDER FIRE™ HITACHI-TYPE STARTER MOTORS
Fits FL 1982 thru 1984, FXR & FLT 1983 thru 1988, FXST 1984 thru 1988,FXE 1974 thru 1988, and XL 1974 thru 1976.
A reproduction of the H-D® OEM electric starter motor used on manyapplications from 1973 thru 1987 is available in chrome or black. Wealso offer many of the replacements parts for this starter motor.
70-138 Complete black starter motor assembly. OEM 31570-73.SOLD EACH
70-139 Complete chrome starter motor assembly. SOLD EACH
OEM 31570-73 & 31559-89T.
B
D
1/65
1
Leaders in New Technology™Leaders in New Technology™Leaders in New Technology™Leaders in New Technology™
AA. GENERATION III STARTERS BY COMPU-FIRE
The GEN III starters are the only starters in the industry that are engi-neered for cranking the large displacement, high compression enginesused in the American made V-TWin without the need forcompression releases. The GEN III starter will produce full start-ing torque drawing only 270 amps from the battery by using high ener-gy neodymium magnets, high efficiency motor windings and 6:1 plane-tary gear reduction. The splined output shaft, steeped jackshaft boltand shortened case design allow just one part number to cover all BigTwin 1990 & later. Also available for Sportster®.
70-198 For 1990 & later Big Twin (shown). SOLD AS KIT
Made by the biggest name in starter drives — Accurate. High qualityand great price.
70-209 Replaces OEM 31567-81. Use on SOLD EACH
Sportster® 1981 thru 1990.70-210 Replaces OEM 31663-90. Use on Big Twin 1991 thru 2002,
and Sportster® 1991 thru 2002.70-211 Best value. Replaces OEM 31663-90. Same application as
above part No. 70-210.
B. STARTER DRIVE CLUTCH ASSEMBLIES
C. START BOOST RELAYThis start boost relay provides full battery voltage to the coil duringcranking, eliminating the 1 -2 volt drop through the wiring harness insingle-fire applications. Makes start-up quicker and easier, especiallywith high compression or stroker engines.
53-123 Start boost relay. SOLD EACH
D. ELECTRICAL RELAYHeavy duty multi use 14VDC electrical relay. Fits Big Twin & Sportstermodels and custom applications.
53-695 Multi use electrical relay 14VDC. OEM 31504-91A. SOLD EACH
70-209
70-210
B
C
D
17-301 Fits Big Twin 1990 & later, and SOLD EACH
Sportster® 1995 & later.
F. DIRECT STARTER BUTTON
70-330 Fits all OEM style 89’ and later 1.2kw, 1.4kw and 1.75kw starters. Same part used on all Thunderfire 1.4 and 1.75kw starters. SOLD AS KIT
E. ULTIMA® THUNDERFIRE STARTER PUSH BUTTON
E
F
G. MINI RELAYThis mini relay can be used as a starter or headlight relay.Replacement relay for Ultima and other aftermarket wiring modules.18-535 Replacement starter/headlight relay. SOLD EACH
G
1/66
11 53-134 STARTER RELAY FL & FLH 1965/1973, XLH 1967/E. 1968, AND XLH L. 1971 / 1974. ZINC FINISH (OEM 71455-67)
53-265 STARTER RELAY 1980/1992 MOST MODELS BIG TWIN & SPORTSTER®. MIDWEST (BEST BUY) (OEM 31506-79B)
53-368 STARTER RELAY 1980/1992 MOST MODELS BIG TWIN & SPORTSTER®. ACCEL (OEM 31506-79B)
NOTE: DUE TO MID YEAR CHANGE, EARLY 1993 APPLICATION IS NOT LISTED. YOU MUST CHECK THE RELAY TO DETERMINE WHICH
TYPE YOU NEED.
53-407 FITS L. 1993 & LATER MODELS BIG TWIN & SPORTSTER® (OEM 31504-91A). ALSO USED AS BRAKE LIGHT RELAY ON 1991 & LATER
FLT MODELS.
53-505 BLUE STREAK STARTER RELAY (OEM 71463-73)
53-287 U.S.A. MADE STARTER RELAY (OEM 71463-73)
2 53-325 OVER RUN SPRING BIG TWIN 1956/1988 AND SPORTSTER® 1965/1980 (OEM 31438-65A)
3 89-46 CHROME SOLENOID COVER
4 53-247 BLACK RUBBER SOLENOID BOOT ALL MODELS (OEM 31444-65A)
5 89-237 CHROME SOLENOID END COVER ALL MODELS. FITS OVER RUBBER SOLENOID BOOT
6 53-321 RUBBER SOLENOID INNER BOOT BIG TWIN 1965/1988 AND SPORTSTER® 1967/1980 (OEM 31441-65A)
4
62
1(53-505, 53-287)
SEE PAGE 1-8 FORELECTRIC CABLES
5
3
1(53-265, 53-368)
STARTER/SOLENOID PARTS FOR H-D® ALL YEARSSOLD EACH EXCEPT AS NOTED
17-40 Fits H-D® 74 C.I. mechanical SOLD AS KIT
brake. Includes OEM 72003-34 & 42280-35.
A. BRAKE LIGHT SWITCH ASSEMBLY
Push off type switch for 1967 thru 1974 Sportster® rear brakes. Canalso be used on many custom applications where the brake pedalpushes against the switch for the off position. Replaces OEM 72004-70.
17-58 Stoplight switch. SOLD EACH
CHROMEPLATED
Rear push type stoplight switch for FX 1973 thru 1977.
17-75 Rear stoplight switch. Replaces SOLD EACH
OEM 72005-73A.
CHROMEPLATED
C. STOPLIGHT SWITCH for SPORTSTER®
B. REAR STOPLIGHT SWITCH for FX
1(53-134)
A
B
C
OEM72003-34
OEM 42280-35
CHROMEPLATED
1/67
1Virtually waterproof. Enclosed terminals. Swivel mounted 5” length.
17-19 Universal application on motorcycles, SOLD EACH
mini-bikes and snowmobiles.
A. UNIVERSAL LUCAS TYPE STOP LIGHTSWITCH
PARTNO. OEM NO. YEAR MODEL
17-43 72002-51A 1951/1973 Servi-Car 750cc/45”).1958/1970 FL & FLH(1200cc/74”).
17-44 72023-71 1979 & Later XL, all models.1971/1984 FL (1200cc/74”, 1340cc/80”).1971 & 1972 FX (1200cc/74”).
Late 1979/1983 FX (1200cc/74”, 1340cc/80’’).1982 & 1983 FXR (1340cc/80”).Late 1984 & All Evolution® Big TwinLater Twin (1340cc/80”, including1991 & 1992 Dyna Wide Glide®).
17-61
17-64
17-65
HEAVY DUTYCONTACTS
17-44
17-43
E. OIL PRESSURE SWITCHES
B. STOPLIGHT SWITCHES for H-D®
HYDRAULIC BRAKES
17-72 Replaces OEM 33900-59. Fits FL & FLH SOLD EACH
1959 thru 1964, FX late 1973 thru early 1979, and Big Twin 5speed 1982 & later.
17-703 Replaces OEM 33901-79. Fits Big Twin 4 speed 1979 & later.17-702 Replaces OEM 33904-00. Fits Softail® 2000 & 2001 and all
Dyna® and FLT 2001.17-701 Replaces OEM 33902-98. Fits Softail® 1998 & 1999 and
Dyna® and FLT 1998 thru 2000.
PLAINMETAL
C. TRANSMISSION NEUTRAL SWITCHES
17-72
17-703
Protect your Harley’s® engine with reliable U.S.A. MADE oil pressureswitches. These oil pressure switches are designed to stringent qualitycontrol specifications, assuring accurate pressure thresholds. Heavy-duty electrical contacts, brass pressure ferrules, rugged thermoplasticinsulators, and corrosion-resistant plated steel shells are used for max-imum dependability.
PART NO. OEM NO. YEAR MODEL
17-61 26552-72 1941/1984 FL, FLHT & FLH-80.1980/1983 FLT & FLHT.1982 & 1983 FXR, FXRS & FXRT.1971/1984 FX, FXE, FXS1200, FXEF-80,
FXS-80, FXB-80 & FXWG-80.17-64 26554-77 L. 1977/1992 XL.17-65 26561-84 1984/1986 All FX Models
1987/1992 All FXR Models1984/1992 All Softail® Models1991 & 1992 All Dyna Wide Glide® models.1984 & 1985 FXRT & FXRS.1984 & 1985 FLT Classic, FLHT Classic.
SOLD EACH
17-74 Fits FX, FXE, XLH & XLCH, 1973 thru SOLD EACH
1977. OEM 70124-75.17-60 Fits FX 1978 thru 1985, FXR 1982 thru 1988 and
XL 1978 thru 1988. OEM 71425-77.
CHROMEPLATED
17-74
17-60
D. IGNITION SWITCHES
A
B
C
D
E
1/68
1
For Big Twin. Replaces OEM 7150136A. Both early cover included.
17-45 Switch with covers & keys. SOLD EACH
17-801 Mechanical switch with round key.17-803 Stainless steel mechanical switch with round key.
F. CHROMED IGNITION SWITCH
D. FAT BOB® STYLE IGNITION SWITCH withROUND KEY
Switch fits FLH, FLHR, and FXDWG models, 1995 & later, and allSoftail® models 1996 & later.
17-115 Switch with round key. Replaces SOLD EACH
OEM 71501-93 & OEM 714313-96.
17-21 U.S.A. MADE 3 Way ignition switch: SOLD EACH
left accessories, center off, right accessories & ignition. Mounts thru 3⁄4” hole.
17-27 U.S.A. MADE 4 Way ignition switch: leftaccessories, center off, right accessories &ignition, extreme right start. Four stud terminal.Mounts thru 3⁄4” hole.
E. IGNITION SWITCH, IGNITION-STARTERSWITCHES
D
E
F
CHROMEPLATED
Universal insulated switch with two screw terminal. Mountsthrough 5⁄8” hole.
17-30 SOLD EACH
C. UNIVERSAL PUSH BUTTON STARTERSWITCH
This is by far the best U.S.A. MADE custom switch you could install.Look at the list of features incorporated into this universal mountedpush button switch:
➤ 60 Amps at 12V.➤ Housing rolled over insulator to seal out dust & moisture.➤ Silver contacts.➤ Black molded plunger.➤ Chrome plated protection collar prevents accidental start.➤ Combination screw and 1⁄4” male blade terminal with locking hole.
17-82 Mounting stem 5⁄8” long, 5⁄8” diameter, SOLD EACH
1-13⁄16” overall length.
B. HEAVY DUTY STARTER SWITCH
B
C
Heavy duty 12v switch measures 7/8” dia. and flush mounts to any flatsurface.
17-133 Polished stainless push button switch. SOLD EACH
A. STAINLESS PUSH BUTTON SWITCHES
17-133
A
1/69
1
17-36 Handlebar light switch to fit H-D®. SOLD EACH
Replaces OEM 71840-29.
CHROMEPLATED
G. HANDLEBAR SWITCH
17-41 Switch for 7⁄8” diameter. SOLD EACH
17-42 Switch for 1” diameter.
F. HORN & HEADLIGHT DIP SWITCHF
G
Now the ignition can have the security of a round key with multi-posi-tion switch. Key won’t fall out in the “Off” position. Fits all FXR & XL,FX 1973 thru 1985, and all FXD. OEM 71428-90A. Easy installation.
17-84 Two-position switch. SOLD EACH
17-124 Three-position switch.
A. ROUND KEY IGNITION SWITCHES
Reproduction of late style switch retrofits to earlier models to give theease of electronic ignition. Resists corrosion & vibration. Includesreversible keys and both styles of switch caps.
17-109 Switch with all stainless steel SOLD EACH
construction (best quality).17-802 Standard switch with round key.17-85 Standard switch.17-804 Stainless steel switch with round key.
CHROMEPLATED
B. FAT BOB® STYLE ELECTRONIC IGNITIONSWITCHES
17-804
This starter switch has fast become a custom builder’s favorite due toits many features. Designed for marine use, it has special weather-proofing & stainless steel terminals. Push key for choke can be used toactivate horn. Overall length 2”, diameter 1-1/2”, mounting hole 13/16”,with flat side so switch can’t turn in hole. Furnished with terminalhardware, mounting nut and two keys. May also use with magneto.Switch housing is made of Black Delrin — “strong stuff.”
17-1 Ignition starter switch. SOLD EACH
C. IGNITION STARTER SWITCH
A
B
C
CHROMEPLATED
Polished stainless switch kit and mounting panel. Includes one pushbutton starter switch, one stop switch, and 2 foot of wiring on a cus-tom 16 gauge polished stainless backing plate that can be mountedanywhere.
17-135 Switch kit w/mounting panel. SOLD AS KIT
D. SWITCH KIT WITH MOUNTING PANEL
D
U.S.A. MADE toggle switches available in 2 position on-off or 3 posi-tion on-off-on. Butt mount thru 1⁄2” hole.
17-46 2 Position, on-off. SOLD EACH
17-47 3 Position, on-off-on.
CHROMEPLATED
17-46
E. HEAVY DUTY TOGGLE SWITCHES
E
1/70
1
17-3 Universal. Mounts anywhere. SOLD EACH
3⁄4” Switch hole.17-9 Locates switch on transmission cover forward
or rear of kicker arm on Big Twin. 3⁄4“ Switch hole.
17-3
17-9
CHROMEPLATED
C. KEY SWITCH PLATES
Chrome cover-up for when you custom mount the ignition switch. Alsoused with our Ultima® rigid Build-A-Bike® kit and our part No. 5-218heavy duty motor mount.
17-25 Custom cover for relocated ignition SOLD EACH
switch.
D. CHROME SWITCH COVER FOR RELOCATION
CHROMEPLATED
17-35 Handlebar starter or horn switch to fit SOLD EACH
H-D®. OEM 71800-26A.
CHROMEPLATED
A. HANDLEBAR PUSH BUTTON SWITCH
Cateye dash mounting plate dimmer switch with knob. Includes tworivets and set screw. OEM 71600-39.
17-57 Fits part No. 21-129 & 21-131 SOLD EACH
cateye mounting plates.
CHROMEPLATED
KNOB
E. DIMMER SWITCH
F. HANDLEBAR WIRING HARNESS KITHandlebar wiring harness kits come 48” long with color coded wires andcover sheath. Switches are attached for both right and left sides.
CHROME BLACK OEM NO. MODEL
18-275 1972 thru 1981 Big Twin .
1973 thru 1981 Sportster®.
18-231 18-230 1982 thru 1995 Big Twin.
1982 thru 1995 Sportster®.
18-331 18-332 1996 & Later Big Twin.
1996 & Later Sportster®.
SOLD AS KIT
STAINLESSSTEEL
12mm Round small stainless steel push button switch includes a special radiusshaped spacer for in-handlebar mounting. Must be used with a switch relay.May be used for turn signal, starter, horn, kill, or high / low. With the spacerremoved, it can be installed on flat surfaces.
17-131 Mini switch. Installation requires SOLD EACH
a 9/32” (7.1mm) drill and 5/16” UNF tap. Includes two 20”wires.
B. MINI PUSH BUTTON SWITCHA
B
C
D
E
G. BIKETRONICS PLUG-IN LIGHTING CONTROL HARNESSES
This harness allows simple plug-in installation so there is no need tosplice or hack into your factory harnesses. It won’t interfere with OEMfunctionality and is compatible with alarm equiped bikes. For FL’s,Touring & Dynas, 1997-up w/TourPak. SOLD EACH.
18-556 Pak Power harness, plug-in auxiliary cigarette lighter style receptacle. Includes safety cap and in-line fuse.
PAK POWER
G
1/71
1
17-91B. HANDLEBAR CONTROL SWITCHES FOR
BIG TWIN & SPORTSTER® 1982 THRU 1995AND 1996 & LATER
17-90 17-89
17-87
A. HANDLEBAR CONTROL SWITCHES FOR H-D®1971 THRU 1981
17-50
17-51
17-52
17-49
These replacements for OEM units are available factory color black orchrome as listed below.
CHROME BLACK OEM NO. DESCRIPTION
17-87 17-53 71547-75 Rocker switch run/off.
17-88 17-54 71546-75 Rocker switch hi/low.17-49 72001-69A Handlebar stoplight switch.17-51 71484-72 Switch for starter, horn, or turn sig-
nal on H-D® handlebar controls.17-89 17-50 71535-72 Long button cap for turn signal
handlebar switch.17-90 17-52 71534-72 Short button cap for turn signal
handlebar switch.
SOLD EACH
Switch assemblies with color coded wire already soldered for easyinstallation. Available in factory color black or chrome style.
1982 THRU 1995CHROME BLACK OEM NO. DESCRIPTION
17-86 71574-82 Handlebar stoplight71590-92 switch.
17-91 17-95 71589-92 Engine run/off, starter.17-92 17-96 71591-92 Right turn switch.17-93 17-97 71597-92 High/Lo, horn.17-94 17-98 71599-92 Left turn switch.
1996 & LATERCHROME BLACK OEM NO. DESCRIPTION
17-100 71590-96 Handlebar stoplight switch.
17-101 17-105 71589-96 Engine run/off, starter.
17-102 17-106 71591-96 Right turn switch.
17-103 17-107 71597-96 High/Lo, horn.
17-104 17-108 71598-96 Left turn switch.SOLD EACH
DIRECT OEM REPLACEMENTS SOLD EACH
PART NO. OEM NO. YEAR MODEL
53-650 26558-84 1986/1993 All Sportsters®.1984/1990 FXST.1986/1989 FLT.
53-651 26557-83 1983/1985 XL, XLS & XLX.1984/1990 All FXR.
53-652 26566-91 1991/1995 All FXST & FLST.
D. BLUE STREAK VOESVACUUM OPERATED ELECTRICAL SWITCHES
High quality U.S.A. MADE vacuum operated electrical switches for useas direct replacements or custom bike building.
SELF ASSEMBLY KITS SOLD EACH
53-653 Set at 3” of mercury.53-654 Set at 4” of mercury.53-655 Set at 5” of mercury.53-656 Set at 6” of mercury.
CHROMEPLATED
Compact horn button/kill switch.
17-5 Switch for 1” diameter. SOLD EACH
C. HORN BUTTON / KILL SWITCH
A
B
C
17-101
17-86
53-650
53-655
D
1/72
1
A. DIAGNOSTIC WIRING SYSTEMSWire Plus offers a complete line of self-diagnostic wiring systems to fit anystock or custom application.
All Wire Plus systems modules feature Solid State breaker technology,(breakers that never need to be replaced) and a replaceable start relay thatcan be purchased at an auto parts store. These components are molded intoan epoxy encapsulated module that is waterproof and vibration resistant.Most systems include a compact pre-assembled harness for easy installa-tion, extended for any frame style. Systems feature onboard LED’s thatdiagnose breakers, start circuits and momentary switch functions, and areavailable in chopper style. (for use with minimal system switches) All WirePlus system connectors are now Deutsch weather proof connectors for theirsmall size and reliability!
18-490 Two Plug ignition harness that provides all sensor wiresrequired by stock, and after market, ignition modules. Includeswires and connectors for: M.A.P. sensor, Crank sensor, BankAngle sensor, Ign. Coil, Ign. module, service engine light,tachometer and Data Link. SOLD AS KIT
18-492 Two Plug ignition harness that must be used with after marketignition modules. Includes wires and connectors for: M.A.P.sensor, Crank sensor, Ign. Coil, Ign. module, service enginelight, tachometer and Data Link. SOLD AS KIT
B. DIGITAL INSTRUMENT PANELS* All digital instruments require digital signal from transmission sensor for speedoand an ignition module with tach output.Rectangular Instrument panels provide speedometer, bar graphtachometer, trip, odometer and all indicator light functions and new flatpanel design that reduces module depth to less than 1” deep with all elec-tronics onboard. (no external brain box) unit measures 2”W x 3.35”L.Features super bright display technology for true daylight readability with alight sensor for auto-dimming at night. Mounting brackets available formost T-bars and 2 piece riser applications. (mounting bracket is requiredand sold seperatly)Digital speedometer with bar graph tachometer.
57-310 Bar mount speedo/tach combination. SOLD AS KIT
57-311 Panel mount speedo/tach combination.
Mounting brackets - required except for panel mount. SOLD EACH
57-312 Mounting bracket for 1” handlebars.57-313 Mounting bracket for 1-1/4” handlebars.57-314 Mounting bracket for 1-1/2” handlebars.57-315 Tab mount for aftermarket digital speedo mounts.
C. MOTOR MOUNTED START SYSTEMChopper style system with chrome billet housing that mounts an automo-tive style start switch (included) and three built-in (hidden) switches forturn signals, high/low and horn. Bolts to any FXR style top motor mountthat does not have threaded holes. Designed to be used with part No. 5-249or 5-250 top motor mount with integral coil bracket.
18-493 Chopper style wiring system. SOLD AS KIT
18-494 Wiring system for use with standard turn signals.18-495 Wiring system w/Auto Cancel Turns and rear lighting control:
Provides a toggle for headlight (low-off-high) and a momen-tary toggle for turns (right-off-left) and a momentary pushbutton for horn. Turns will be automatically canceled and rearturns will be running and brake lights also.
17-128 Motor mounted chrome billet housing that accepts an automo-tive style start switch (included).
WIRE PLUS MODULAR MOTORCYCLE WIRING SYSTEMS & ACCESSORIES
MOTOR MOUNTED WIRING SYSTEM
DIGITAL INSTRUMENT PANEL
SYSTEM MODULE SHOWN ACTIVATED UNDER WATER
Wire Plus offers a complete line of self-diagnostic wiring systems to fit any stock or custom application. All Wire Plus systems featuresolid state breaker technology, (breakers that never need to be replaced) and all components are combined in one compact weather-proof design.
MOUNTING BRACKETS
A
B
C
1/73
1A. AUTOMOTIVE START MID FRAME SYSTEMThis new system is the ultimate chopper style wiring system. The pre-assembled harness is configured for an automotive style start switch (soldseperatly) which eliminates start circuit wiring in the harness. It features asolid-state breaker pack (breakers that will never burn out) that measuresapprox. 1”x 1” and is molded in waterproof epoxy with diagnostic Led’s. Thissystem is supplied with an installation kit that allows the builder toadd indicator and turn signal wires.18-497 This kit mounts breaker module and ignition SOLD AS KIT
switch at the motor mount area.18-498 Mid Frame system with chopper style harness for automotive
style start.
B. Z1 MINI MID FRAME SYSTEMThese new systems have the smallest power modules ever! Designed forBobber and Chopper style bikes with a round oil tank or springs under theseat with no place to hide anything. This module is supplied with a billetaluminum cover, for visible mounting, with holes for viewing diagnosticlights and measures just 1.8” W x 2” H x .85” Deep! Mounts anywhere inthe oil tank area. Auto-cancel module sold separately. 18-527 Mid Frame system with harness for stock style handlebar
controls.With or without turns or auto-cancel. SOLD EACH
18-528 Mid Frame system with chopper style harness for minimalsystem switches. With or without turns.
18-524 Mid Frame system with harness for stock style handlebarcontrols. Includes a seperate 15 amp breaker and wiring forcorrect connection of compression releases needed for biginch motors. With lighting control module included.
C. Z1 STANDARD MID FRAME SYSTEMSame features as Z1 Mini but supplied with longer billet cover for mountingof both modules in one compact location. SOLD EACH
18-525 Mid Frame system with harness for stock style handlebar controls. With lighting control module included.
18-526 Mid Frame system with harness for stock style handlebarcontrols. Includes a separate 15 amp breaker and wiring forcorrect connection of compression releases needed for biginch motors. With lighting control module included.
D. BILLET TOP MOTOR MOUNTChromed billet construction, provides a coil mounting location that is upand behind the normal top motor mount leaving this area open for WirePlus switch housings and other billet products. Mounts Twin Cam coils andmost new style coils that do not have the electrical connections on theends. (Crane Hi-4, Dyna 2000i) NOTE: Due to motor and frame variations and this coil mounting location this part will require custom fitting to your applicaton. Spacing will berequired.5-249 Fits all Twin Cam® & Evolution® engines up to 100 C.I. SOLD EACH
5-250 Fits all Twin Cam® & Evolution® engines 101 C.I. and up.
E. 005 SERIES FLAT SIDE TANK STYLEMounts under ignition switch between flat side gas tanks. Auto cancelmodule sold separately.
18-512 Flat side system with chopper style harness forminimal switches. Works with or without turn signals.
SOLD AS KIT
WIRE PLUSMODULAR MOTORCYCLE WIRING SYSTEMS & ACCESSORIES
BILLET TOP MOTOR MOUNT
AUTOMOTIVE START MID FRAME SYSTEM
Z1 MINI MID FRAME SYSTEM
Z1 STANDARD MID FRAME SYSTEM
A
B
C
D
1/74
1
17-126 & 17-127WINGED BILLET IGNITION SWITCH HOUSINGS
C
A. SEAT POST WIRING SYSTEMSWire Plus seat post wiring systems are billet construction with built inignition switch. Mounts to the seat post coil bracket on Big Twins from1941 thru 1984 and custom frames using the same style coil mount.Includes a built in power module, with diagnostic LED’s, that providesa complete breaker system for the protection of all components, includ-ing electric compression releases. Also features a replaceable startrelay, circuitry for headlight off at startup & optional connections forneutral and clutch switch safety found on 2007 & up controls.
18-499 Chrome Seat Post system with pre-assembled harness forstock style handlebar controls. Includes auto-cancel /lighting control module to run rear turns as running lightsbrake lights and turn signals. SOLD AS KIT
18-500 Chrome Seat Post system with Automotive start switch and pre-assembled chopper style harness for minimal system switches. Can be used with or without turn signals. SOLD AS KIT
18-501 Seat post system with chopper style harness. Includesstart switch, high/low switch and latching module.SOLD AS KIT
B. MOTOR MOUNTED WIRING SYSTEMBillet construction with built in ignition switch. Mounts to most FXRstyle top motor mounts. Includes a built in power module, with diag-nostic LED’s, that provides a complete breaker system for the protec-tion of all components, including electric compression releases. Alsofeatures a replaceable start relay, circuitry for headlight off at startup &optional connections for neutral and clutch switch safety found on2007 & up controls.18-502 Chrome Motor Mount system with pre-assembled harness
for stock style handlebar controls. Includes auto-cancel / lighting control module to run rear turns as running lightsbrake lights and turn signals.
C. WINGED BILLET IGNITION SWITCH HOUSINGS17-126 Mounts to most FXR style top motor mounts that do not
have threaded mounting holes. It houses the 1996 & up Fat Bob style ignition switch (with removable barrel key) usually found between Fat Bob style gas tanks. Chromed billet construction. Ignition Switch not included. SOLD EACH
17-127 Same features as the 17-126 but also mounts a momen-tary start switch & a latching Hi- Low Beam switch(included) hidden behind the end of the housing. Thiseliminates the need for a latching relay. Chromed billetconstruction. Ignition Switch not included.
D. BILLET IGNITION SWITCH HOUSINGMounts to any FXR style top motor mount that does not have threadedmounting holes. It will house a 1996 & later Fat Bob® style ignitionswitch (with removable barrel key) usually found between Fat Bob®
style gas tanks. Chromed billet construction. NOTE: Ignition switch not included.
17-129 Switch housing. SOLD EACH
E. BILLET IGNITION SWITCH HOUSING WITH COIL BRACKET18-521 Mounts to most FXR style top motor mounts that do not
have threaded mounting holes. Houses the 1996 & up Fat Bob style ignition switch (with removable barrel key)usually found between Fat Bob style gas tanks. For use with most coils that do not have electrical connections on the ends. Chromed billet construction. Ignition switchnot included (Fits new style: Crane HI-4, Dyna 2000i Twin Fire, ect) SOLD EACH
WIRE PLUSMODULAR MOTORCYCLE WIRING SYSTEMS & ACCESSORIES
SEAT POST STYLE
MOTOR MOUNT STYLE
A
B
17-129 BILLET IGNITION SWITCH HOUSING
18-521 BILLET IGNITION SWITCH HOUSING
D
E
1/75
1A. BILLET COIL COVER89-287 Chrome billet coil cover for use with most coils that do
not have electrical connections on the ends. Mounts to most FXR style top motor mounts that do not have threaded mounting holes. Chromed billet construction. (Crane HI-4, Dyna 2000i Twin Fire, ect) SOLD EACH
B. WIRE PLUS ACCESSORIES17-130 Ignition switch housing for motor mount SOLD EACH
applications. Includes three position switch.18-515 Auto cancel turn signal module with load SOLD EACH
equalization.18-518 High/low latching module (momentary SOLD EACH
input with latching output).18-519 Switch control module. Provides latching SOLD EACH
circuits for momentary (petite) style switcheswith auto cancel.
18-520 Lighting control module. Provides auto- SOLD EACH
cancel circuit with turn signals as runningand brake lights with modulation.
WIRE PLUSMODULAR MOTORCYCLE WIRING SYSTEMS & ACCESSORIES
18-518 HIGH/LOW LATCHING MODULE
18-520 LIGHTING CONTROL MODULE
17-130IGNITION
WITHHOUSING
89-287COIL BRACKET
A
B
C. TWIN FIN COIL COVER / IGNITION SWITCH
This chrome plated billet aluminum coil cover is made to resemble a V-Twin style motor. Will work on coils mounted between cylinders on thetop motor mount.
89-606 Coil cover with key switch (shown). SOLD EACH
D. IGNITION SWITCH / COIL COVER
89-608 Coil cover with key switch hole 3/4”. SOLD EACH
(does not come with switch)
BILLET ALUMINUM
C
D
CHROMEPLATEDBILLET
1/76
1U.S.A. MADE stock length black harnesses come in kit form andincludes main wiring harness for each model. Color coded with pre-attached wire ends.
BIG TWIN
18-187 For 1948 thru 1957 WL, UL, FL and FLH. SOLD AS KIT
OEM 70321-48.18-188 For 1958 thru 1964 FL and FLH. OEM 70321-58.18-189 For FLH 1965 thru 1969. OEM 70321-65.18-190 For FLH 1970 thru 1972. OEM 70320-70.18-191 For FLH 1973 thru 1977. OEM 70320-73.18-258 For FLH 1978 & 1979. OEM 70320-78.18-259 For FLH 1980 thru 1984. OEM 70320-80.18-192 For FX 1970 thru 1972. OEM 70326-70.18-193 For FX 1973 thru 1977. OEM 70326-73.18-260 For FXWG 1980 thru 1985. OEM 70214-80A.
18-264 Turn signal wiring kit for FL & FLH, SOLD AS KIT
1957 thru 1969.
SPORTSTER®18-261 For 1968 & 1969 XLH electric start. SOLD AS KIT
18-262 For 1970 thru 1972 XLH electric start.18-263 For 1975 & 1976 XLH electric start.18-265 XLH auxiliary wiring harness for use in SOLD AS KIT
conjunction with above main harnesses.For headlight, taillight, handlebar switches,etc.
U.S.A. MADE black vinyl covering resists corrosion, abrasion, oil,etc. Easily pulled through tight spaces. Heavy 16 gauge, not thelight 18 gauge wire.
18-2 100 Foot roll. SOLD AS ROLL
12” extended wiring harness for handlebars. Color coded. Kit includesconnectors and clips.
18-104 Fits 1973 thru 1981. SOLD AS KIT
18-222 Fits 1982 thru 1990.
B. EXTENDED WIRING HARNESSES
D. HANDLEBAR WIRING HARNESS KIT
A. WIRING HARNESSES
E. PRIMARY WIRE ( 16 GAUGE )
Handlebar wiring harness kits come 48” long with color coded wiresand cover sheath. Switches are attached for both right and left sides.
Fits Big Twin 1972 thru 1981 and Sportster® 1973 thru 1981.18-275 With Black switches. SOLD AS KIT
Fits Big Twin and Sportster®, 1982 thru 1995.18-230 With Black switches. SOLD AS KIT
18-231 With Chrome switches.
Fits Big Twin and Sportster®, 1996 & later.18-332 With Black switches. SOLD AS KIT
18-331 With Chrome switches.
U.S.A. MADE. If you’re building from the ground-up or replacing stockwiring, these kits are the hot ticket. Connectors, wire lengths, and wirecolor codes are just like stock. Kits include main harness, handlebarwiring, rear lamp wiring, and dash harness where applicable.
18-333 For FXST 1989 thru 1990. SOLD AS KIT
18-330 For FXST 1991 & 1992.18-335 For FXST 1993 thru 1995.18-336 For FXR/S 1989 thru 1990, without dash.
C. WIRING HARNESSES FOR LATE MODEL FX
18-230
18-331
A
B
C
D
E
1/77
1
D
RIGHT H-BAR GROUND IS MAIN GROUND
C. ULTIMA COMPLETE ELECTRONIC WIRING SYSTEMThis wiring system uses all the latest high tech electronics to makewiring your bike easier. All flasher, relay & circuit interrupters areincluded in one small package that can be mounted in a wide variety oflocations. This module and its plugs are waterproof and LED’s are usedto troubleshoot problems. Kit includes all wires, connectors, module &heat shrink tubing. Instructions included and available online @www.ultimaproducts.com.
18-530 Ultima® wire harness kit. SOLD AS KIT
18-531 Indicator light harness for above part No. 18-530wiring system. 6 Ft. long; can be cut to desired length.
SOLD EACH18-535 Replacement starter/headlight relay. SOLD EACH
B
A
A. ULTIMA PLUS ELECTRONIC WIRING SYSTEMThe newest version of Ultima’s complete wiring systems. This one iseven smaller & more advanced, includes everything needed for instal-lation. Measures 1-13/16 x 3-7/8 x 1. Instructions included and availableonline @ www.ultimaproducts.com.
18-533 Complete kit. SOLD AS KIT
B. ULTIMA SIMPLE WIRING MODULEUltima’s simple wiring module was designed to help simplify wiringwhen only the bare necessities are needed. No larger than a standardstarter relay, the module provides 30 amps secondary protection to themotorcycle’s electrical system. Has a built-in starter relay. Allowsusage of a low amperage ignition switch. Has diagnostic L.E.D.s forignition and start circuit. Compatible with electronic compressionreleases. Instructions included and available online @www.ultimaproducts.com.
★18-536 Ultima® Simple Wiring Module. SOLD EACH
CD. ULTIMA CUSTOM WIRING HARNESS FOR
BIG TWIN CUSTOMS
This new wiring harness is perfect for custom motorcycles using 1985thru 1995 or 1996 & later handlebar controls. Harness is a completemain wiring harness and installs easily for a clean, custom look.Harness is complete to include starter relay, turn signal flasher, circuitbreakers and all necessary pin connectors to install with either 1985thru 1995 or 1996 & later handlebar controls. Use this kit with handle-bar wiring harness part No. 18-230, 18-231, 18-332 and 18-331 found onbelow.18-346 Complete custom main wiring harness. Fits custom FX
models 1985 & later. SOLD AS KIT
1/78
1
WIRE HARNESS KIT18-337 Kit for Fat Bob® tank mounting of module SOLD AS KIT
DASH LIGHT COMPONENTS18-341 Panel for L.E.D. dash mounted lights. SOLD EACH
18-338 Panel for incandescent dash mounted lights.18-340 Harness; 16” long for above dash panels.18-339 Harness; 6’ long for handlebar mounted indicator lights.
B. COMPLETE ELECTRONIC WIRING HARNESS FOR CUSTOM BUILDERS
18-33818-339 18-340
18-341
18-337KIT
B
A. MICRO HARNESS CONTROLLERThunder Heart Performance is pleased to announce the availability oftheir new Micro harness Controller! The Micro Harness Controllerconsolidates all of the electronic functions of a motorcycle (with theexception of instrumentation and engine management) into one, easy-to-hide system! The Micro Harness Controller avoids the wiring“bird’s nest” of other systems so you spend less time wiring yourbike...and more time riding!
Perfect for choppers and saddle tank bikes, the system includes a billetaluminum controller housing, un-terminated “fantail” harness, shrinktubing, and all necessary connectors, and a comprehensive instructionand troubleshooting manual. The result is a durable, professionalinstallation.18-532 Wire Harness sold as kit
A
This complete harness and module allows for true “plug & play” elec-tric wiring. Includes all fuse and flasher components and solid statecircuitry is state of the art. Uses AMP type & Molex connectors for easeof service. Utilizes high tech circuit interrupters instead of mechanicalbreakers. It will even tell you what section of wiring has a short in it tosimplify troubleshooting. Kit includes full harness, module, connec-tors, shrink tubing, and easy-to-follow instructions.
1/79
1
B. CIRCUIT BREAKER MOUNT BRACKET
18-18 U.S.A. MADE fuse holder. Complete with SOLD EACH
6” of 16 gauge wire looped, and 20 amp fuse.
U.S.A. MADE rugged steel bracket with detents permit simple snap-inof circuit breakers. Holds two breakers. A must for the custom builder.Cad plated for rust-free long wear.
17-80 Circuit breaker mount bracket. SOLD EACH
CADPLATED
Ideal waterproof U.S.A. MADE fuseholder. Designed for applica-tions where moisture is a problem. Cap has positive snap actionfor tight fit. 4” Leads (12 gauge). For mini fuse only. Fuses avail-able separately below.
18-19 Waterproof fuse holder. SOLD EACH
Replacement mini fuse. Fits above part No. 18-19 waterproof fuseholder.18-20 15 Amp fuse. SOLD EACH
18-21 20 Amp fuse.18-23 30 Amp fuse.
18-19
18-20
This quality reproduction terminal box is now available pre-assembled,painted black, and ready to install. They are properly insulated to elim-inate grounding and include all necessary mounting hardware. Theinstallation of this box and a new wire harness is a must when restor-ing the electrical system on Big Twins and 45”, 1948 thru 1969.
17-99 Terminal box assembly. SOLD AS KIT
D. ELECTRICAL TERMINAL BOX ASSEMBLY
A. CIRCUIT BREAKERS TYPE 1 CYCLING -AUTOMATIC RESET
G. WATERPROOF FUSE HOLDER
NOTES: PLASTIC VS METALVibration…Plastic housings with mounting brackets are one-piecemolded designs and are less prone to vibration. Metal housings withbrackets are two-piece designs. The bracket is attached by spot weld-ing and can be loosened by vibration.Shorting Out…If a wire should loosen from a terminal on a plastichousing version, it will not short out against the housing as it may dowith a metal housing.Weight…The plastic housing is also lighter than the metal housing.The following part numbers include single U.S.A. MADE circuit break-er with mounting bracket.
METAL PLASTICPART NO. DESCRIPTION PART NO.
17-78 Circuit breaker; 15 amp. 17-12017-63 Circuit breaker; 20 amp. 17-12117-79 Circuit breaker; 30 amp. 17-122
SOLD EACH
U.S.A. MADE circuit breakers for use with snap-in bracket (see right).METAL PLASTICPART NO. DESCRIPTION PART NO.
17-76 Circuit breaker; 15 amp. –––OEM 74589-73.
17-77 Circuit breaker; 20 amp. 17-11817-62 Circuit breaker; 30 amp. 17-119
OEM 74599-77.SOLD EACH
E. FUSE HOLDER
17-7617-120
17-125 12V Rectangular flasher. For XL 1965 & later, FL1965 thru 1984, FLT 1980 & later, FX 1971 & laterand FXR 1982 & later.SOLD EACH
F. FLASHER
This U.S.A. MADE terminal block is another trick item for custom bikesthat gives the wiring job a professional look. Available with 4 terminalstuds. 10 - 24 Thread for long life. ABS base for rugged use.
17-81 Terminal block, 41⁄2’’ long. SOLD EACH
C. TERMINAL BLOCK
A
B
C
D
E
F
G
1/80
1
97-305 Pin crimp tool, for solid pins only. SOLD EACH
97-308 Pin crimp tool, for open crimp pins only.
A. DEUTSCH CRIMP TOOL
DEUTSCH CONNECTORSA
18-565 Open crimp pins, 16-18 gauge wire. OEM 72190-94. PKG. OF 100
18-566 Open crimp sockets, 16-18 gauge wire. OEM 74191-94. PKG. OF 100
18-567 Solid crimp pins, 16-18 gauge wire. OEM 72190-98. PKG. OF 100
18-568 Solid crimp sockets, 16-18 gauge wire. OEM 74191-98. PKG. OF 100
B. DEUTSCH PINS AND SOCKETS
B2-WIRE CONNECTOR 6-WIRE CONNECTOR18-569 Grey, OEM 72102-94GY. 18-606 Grey, OEM 72106-94GY.18-601 Black, OEM 72102-94BK. 18-607 Black, OEM 72106-94BK.3-WIRE CONNECTOR 8-WIRE CONNECTOR18-602 Grey, OEM 72103-94GY. 18-608 Grey, OEM 72108-94GY.18-603 Black, OEM 72103-94BK. 18-609 Black, OEM 72108-94BK.4-WIRE CONNECTOR 12-WIRE CONNECTOR18-604 Grey, OEM 72104-94GY. 18-610 Grey, OEM 72109-94GY.18-605 Black, OEM 72104-94BK 18-611 Black, OEM 72109-94BK.
SOLD EACH
C. DEUTSCH RECEPTACLES REQUIRE DEUTSCH OPEN OR SOLID CRIMP PINS
C
18-602 18-607
2-WIRE CONNECTOR 6-WIRE CONNECTOR18-612 Grey, OEM 72112-94GY. 18-618 Grey, OEM 72116-94GY.18-613 Black, OEM 72112-94BK. 18-619 Black, OEM 72116-94BK.3-WIRE CONNECTOR 8-WIRE CONNECTOR18-614 Grey, OEM 72113-94GY. 18-620 Grey, OEM 72118-94GY.18-615 Black, OEM 72113-94BK. 18-621 Black, OEM 72118-94BK.4-WIRE CONNECTOR 12-WIRE CONNECTOR18-616 Grey, OEM 72114-94GY. 18-622 Grey, OEM 72119-94GY.18-617 Black, OEM 72114-94BK. 18-623 Black, OEM 721129-94BK.
SOLD EACH
D. DEUTSCH PLUGSREQUIRE DEUTSCH OPEN OR SOLID CRIMP SOCKETS
D
18-615 18-618
97-305
18-634 Male open crimp style. PKG. OF 50
18-635 Female open crimp style. PKG. OF 50
G. DELPHI TERMINALS
18-624 1-wire connector. 18-627 5-wire connector.18-625 2-wire connector. 18-626 3-wire connector.
SOLD EACH
H. DELPHI SEALED MALE CONNECTORSREQUIRE OPEN CRIMP MALE TERMINALS
18-629 1-wire connector. SOLD EACH
18-630 2-wire connector.18-631 3-wire connector.18-632 5-wire connector.
I. DELPHI SEALED FEMALE CONNECTORSREQUIRE OPEN CRIMP FEMALE TERMINALS 97-306 Removes terminals from connectors. SOLD EACH
97-307 Crimps most U-barrel terminals SOLD EACH
F. DELPHI TOOLS
DEUTSCH OPEN CRIMP PINS
DEUTSCH SOLID CRIMP PINS
DELPHI CONNECTORS
Kit contains (4) 12s, 8s, 4s, 3s & 2s, (6) 6s & 100 pins and sockets.18-658 Deutsch builders kit, black. SOLD AS KIT
18-659 Deutsch builders kit, gray. SOLD AS KIT
E. DEUTSCH BUILDERS KIT
18-628 Delphi cable seals. SOLD EACH
J. REPLACEMENT DELPHI CABLE SEALS
18-565 18-566
1/81
1AMP MULTILOCK (OEM REPLACEMENT) CONNECTORS
18-660 2-wire connector. SOLD EACH
18-636 3-wire connector.18-661 4-wire connector.18-637 6-wire connector.18-638 8-wire connector.
A. AMP MULTILOCK CAP CONNECTORSREQUIRE OPEN CRIMP STYLE PINS
18-662 2-wire connector. SOLD EACH
18-639 3-wire connector.18-663 4-wire connector.18-640 6-wire connector.18-641 8-wire connector.
B. AMP MULTILOCK PLUG CONNECTORSREQUIRE OPEN CRIMP STYLE SOCKETS
18-642 Open crimp style pins. PKG. OF 100
18-643 Open crimp style sockets. PKG. OF 100
C. AMP MULTILOCK PINS AND SOCKETS
A unique assortment of commonly used amp plugs and caps.Contains 8 each of the 8, 6, 4, 3 and 2 wire connectors. Along with100 pins and sockets.18-644 AMP builders kit. SOLD AS KIT
D. AMP MULTILOCK BUILDERS KIT
18-645 2-wire connector. SOLD EACH
18-646 3-wire connector.18-647 4-wire connector.18-648 6-wire connector.18-664 9-wire connector.18-665 12-wire connector.
E. AMP UNIVERSAL CAP CONNECTORSREQUIRE OPEN CRIMP STYLE SOCKETS
18-649 2-wire connector. SOLD EACH
18-650 3-wire connector.18-651 4-wire connector.18-652 6-wire connector.18-653 9-wire connector.18-654 12-wire connector.
F. AMP UNIVERSAL PLUG CONNECTORSREQUIRE OPEN CRIMP STYLE PINS
18-655 Open crimp style pins. OEM 72038-71. PKG. OF 100
18-656 Open crimp style sockets. OEM 72039-71. PKG. OF 100
G. AMP MATE-N-LOCK PINS AND SOCKETS
A unique assortment of commonly used amp plugs and caps.Contains 6 each of the 12 and 2 wire connectors. 8 of the 9 and 6wire connectors. 4 of the 3 and 4 wier connectors. Along with 100pins and sockets.18-657 Mate-n-lock builders kit. SOLD AS KIT
H. AMP MATE-N-LOCK BUILDERS KIT
AMP MULTILOCK
AMP MATE-N-LOCK
AMP MATE-N-LOCK CONNECTORS
18-642
18-643
1/82
1
These U.S.A. MADE cable ties are made from a weather resistant UVblack nylon.
18-12 7” Cable tie; solid type. SOLD EACH
18-14 11” Cable tie; solid type.
CHECK QTY. DISCOUNT FOR BEST PRICE
Compact and sturdy U.S.A. MADE tool that tightens and cuts cable tiesin one operation. Adjustable tension control to 50 lbs. This tool workswell in hard-to-get-at places.
97-105 Cable tie tool. SOLD EACH
BLACK
97-105
C. CABLE TIES & INSTALLATION TOOL
E. CHROME CABLE TIESMade from weather-resistant UV nylon. Available in three differentlengths.
18-325 4” Long tie. SOLD EACH
18-326 8” Long tie.18-327 12” Long tie.
CHROME
This U.S.A. MADE insulation tubing is the only thing to use for safe,clean, custom wiring jobs. Cut to length, thread your wires, carefullyapply heat and watch what happens. The insulation shrinks to a per-fect custom fit around your wires. Easy to use. Available in bulk orprecut lengths.
18-91 1⁄4” x 5’ Tubing. SOLD EACH
18-93 3⁄8’’ x 5’ Tubing.18-92 1⁄4” x 50’ Tubing.18-94 3⁄8” x 50’ Tubing.
A. HEAT SHRINK TUBING
16-13 Squeeze bulb horn, 7” long. SOLD EACH
This air horn produces total sound output of 107 decibels. Ideally suitedfor application on motorcycles and autos where mounting space is lim-ited and air horns cannot be used. Relay, brackets and hardwareincluded in blister packed set.
16-17 Electric horn, 107 decibles. SOLD AS SETCHROMEPLATED
F. SQUEEZE BULB HORN
D. ELECTRIC HORN
Early style horn.
16-18 12V Horn. SOLD EACH
CHROMEPLATED
G. H-D® STYLE ELECTRIC HORN
Chrome plated horn cover echoes classic styling.
89-491 Fits 1991 & later Big Twin and Sport- SOLD EACH
ster®. Will work on many custom applications.
B. AIR CLEANER STYLE HORN COVER
A
B
C
D
E
F
G
1/83
1This is a chrome plated reproduction of the original 1949 thru 1958 Panhorn and added special brackets to fit Evolutions® & Shovels. Withslight modifications the horn will fit all Big Twin motors.
16-31 12V Horn assy. for Softail® models SOLD AS KIT
1984 thru 1990. Works with the stockexhaust system and air cleaner.
16-23 12V Horn assy. for Pan & Shovel.
CHROMEPLATED
A. TRUMPET HORN
F. SKULL KROMETSA decorative fastener that can be used anywhere on the bike but isbest suited for license plate mounting. The finish and detail of theskull is top quality. Comes with removable stud, nut, lock and flatwasher. 1” High, 5⁄8” wide. 1⁄4-20.
CHROME SKULLS41-960 Painted Black eyes. SOLD EACH
41-961 Purple jeweled eyes.41-962 Indigo Blue jeweled eyes.41-963 Crimson Red jeweled eyes.41-964 Emerald Green jeweled eyes.41-965 Golden jeweled eyes.
GOLD SKULLS41-966 Painted Black eyes. SOLD EACH
CHECK QUANTITY DISCOUNT FOR BEST PRICE SEESECTION 14 FOR “BIG DADDY” SKULLS
High quality chrome finish. Comes with mounting bracket.
16-21 6 Volt horn. SOLD EACH
16-22 12 Volt horn.
Stock style horn cover. Chrome plated.
89-414 Fits 1986 thru 1992 Sportster® and 1991 SOLD EACH
& 1992 FLT & Softail®. OEM 69012-86A.
This 12V horn with spade style terminals has a universal mountingbracket and a chrome plated snap-on cover.
16-32 12 Volt universal horn. SOLD EACH
Cigarette lighter and mounting bracket, with wire.
18-83 Cigarette lighter; fits any bike. SOLD EACH
CHROMEPLATED
CHROMEPLATED
B. HORN COVER
C. SINGLE HORN
D. CUSTOM UNIVERSAL HORN WITH COVER
E. CIGARETTE LIGHTER
A
BC
D
E
F
1/84
1 NOTES