fuel d eliver y - nickels performance
TRANSCRIPT
59FU
EL DELIV
ERY
EZ-EFI 2.0® SELF TUNING ENGINE CONTROL SYSTEM BASE KIT - 30400-KIT
EZ-EFI SELF-TUNING FUEL INJECTIONSYSTEMS - 30226-KIT
The EZ-EFI 2.0® Base Kit includes everythingneeded for an EFI conversion except an EFI supported fuel system. FAST™ also offers Master Kits that include in-tank or inline fuel pump kits.• Full Color Touch Screen Display w/Garmin
GPS-Style Suction Cup Mount• 1200 HP-Capable Throttle Body w/ Internal Fuel
Injectors & Sensors• Fully Mesh Wrapped Main Harness w/Wide-Band
O2 Sensor• USB Communications Cable• Engine Control Unit (ECU)
FAST EZ-EFI Self-Tuning Carburetor to ElectronicFuel Injection Conversion Kit. No laptop or tuningexperience needed! This kit includes the following:Throttle Body, Fuel Injector, Sensor & gasket,Wiring Harness, Hand held control module withcable & power adapter, EZ-EFI control unit, CoolantTemp Sensor 3/8" NPT (1/2" NPT AdaptorIncluded), and a wide band O2 sensor, bung &plug. FAST® engineers set out to develop the ultimate fueling strategy for the EZEFI ®.
EZ-EFI SELF-TUNING FUEL INJECTIONSYSTEMS - 30227-KITEasy-to-use setup wizard provides compre-hensive walk-through and system tunesitself. System includes ECU, wide-bandoxygen sensor, wiring harness, fuel injec-tors, fuel pump kit and throttle body for aneasy installation. Bolts on to ANY naturallyaspirated, gasoline engine up to 600 hp.Protected by a limited lifetime warranty soyou can purchase with peace of mind; Idealfor street rods and muscle cars
Fuel13v4o_Layout 1 10/31/13 2:14 PM Page 59
77FU
EL DELIV
ERY
STREET PERFORMANCECARBURETORS
#0-7448
Intended for short circle track racing. Chokehardware and related provisions are deleted forsmoother airflow. 30cc accelerator pump, GFLTdiaphragm.
DESCRIPTION PART NO.350 CFM, Metering block w/changeable emulsion bleeds 0-80787-1
500CFM, HP metering block w/non-adjustable metering 0-80583-1
Manual choke. Center hung float bowl. Universalthrottle lever. Ford A/T kickdown. Power valveblow-out protection. All metal parts. Withoutautomatic overdrive transmission. Non-emission.
2-BBL KEITH DORTON COMPETITIONCARBURETORS
DESCRIPTION PART NO.350 CFM, 2 bbl. w/30cc accelerator pump 0-7448
500 CFM, 2 bbl. w/50cc accelerator pump, classic finish 0-4412C500 CFM, 2 bbl. w/50cc accelerator pump, shiny finish 0-4412S
DESCRIPTION PART NO.Stock-300HP - 570 CFM 0-80570300-400HP - 670 CFM 0-80670400-500HP - 770 CFM 0-80770
500+HP - 870 CFM 0-80870
STREET AVENGER™ CARBURETORSAll Holley Street Avenger components are dyno matchedspecifically for the key engine families used by today’sstreet performance enthusiast. All components areSTREET READY RIGHT OUT OF THE BOX!
DESCRIPTION PART NO.750 CFM, Vacuum Secondary, Single Inlet, Shiny FR-3310S
350 CFM, 2BBl Manual Choke, Single Inlet, Classic FR-7448
REMANUFACTURED CARBURETORSClassic or Shiny finish.
SEASONAL
DESCRIPTION PART NO.670 CFM, 4bbl. 0-90670
Side hung floats. Electric choke. Quick-changevacuum secondary. Spring-loaded needle andseat assemblies. Power valve blow-outprotection. 4 Vacuum ports. High vacuum signalprimary annular boosters. universal with FordA/T kickdown lever.
TRUCK PERFORMANCE CARBURETORS
ULTRA CARBURETORS
PART NUMBER DESCRIPTION
0-86670RD 670 CFM "Ultra" Street Avenger (RED)
0-86770RD 770 CFM "Ultra" Street Avenger (RED)
0-76750RD 750 CFM "Ultra" Double Pumper (RED)
0-76750BL 750 CFM "Ultra" Double Pumper (BLUE)
0-76750BK 750 CFM "Ultra" Double Pumper (BLACK)
All aluminum construction and areequipped with metering blocks and abase plate made from 6061–T6 billet aluminum. Three differentanodized color options (Red, Blue, or Black). Approximately 5 lbs lessthan a comparable zinc carburetor. Vacuum secondaries allow use ona wide variety of vehicles4 corner idle, 1 timed (spark) port, 2 fullvacuum, and 1 PCV port. Electric Choke.
PART NO. DESCRIPTION0-82751 Mechanical Secondary Double Pumper
750 CFM STREET/STRIP HP CARBURETORS Best Value in a Dual Purpose Street and LightCompetition Carburetor. Model 4150 Street HP;Contoured Main Body. No Choke. 4-bbl.
SPECIALORDER
Double pump. Mechanical secondaries. Dualfeed/center hung float bowls. Manual choke.Power valve blow-out protection. All metal parts.Non-emission. Classic (C) or shiny finish (S).
DESCRIPTION PART NO.600 CFM, 4 bbl. w/center hung floats 0-4776C
650 CFM, 4bbl. vacuum secondary 0-80783C650 CFM, 4 bbl. w/center hung floats 0-4777C
650 CFM, 4 bbl., w/center hung floats, shiny finish 0-4777S750 CFM, 4 bbl. with 4 corner idle system, classic finish 0-4779C750 CFM, 4 bbl. with 4 corner idle system, shiny finish 0-4779S
800 CFM, 4bbl., mechanical secondary 0-4780C850 CFM, 4 bbl. with 4 corner idle system 0-4781C
STREET PERFORMANCE DOUBLE PUMPERSTM
600-850 CFM CARBURETORS
DESCRIPTION PART NO.650 CFM, GM, 4 bbl 0-80555C
650 CFM STREET PERFORMANCECARBURETORSModel 4175 carburetors include your choice ofvacuum or mechanical secondary, an acceleratorpump, power blow out protection, a spread boreflange and choke.
Fuel13v4o_Layout 1 10/31/13 2:17 PM Page 77
78FU
EL D
ELIV
ERY
Calibrated for small displacement V-8 or 6cylinders. Electric choke. Single feed/side hungfloat bowls. Universal throttle lever. Vacuumsecondaries. Non-emission. 4bbl.
600 CFM UNIVERSAL STREETPERFORMANCE CARBURETOR
DESCRIPTION PART NO.600 CFM, w/manual choke (64 & earlier), classic finish 0-1850C600 CFM, w/manual choke (64 & earlier), shiny finish 0-1850S600 CFM, with electric choke & Ford A/T kickdown
lever (1965-69), shiny finish0-80457S
Universal. Double-step down leg boosters. Calibrated for gasoline. Progressive mechanical secondaries. 30cc accelerator pumps. PCV, spark & manifold vacuum ports.
PRO-SERIES HP CARBURETORS
DESCRIPTION PART NO.390 CFM, 4bbl. universal with Ford A/T kickdown lever 0-8007
450 CFM, 2 X 4 tunnel ram 0-9776
Manual choke. Dual feed/center hung float bowls.Vacuum secondaries. Power valve blow-out protec-tion. All metal parts. Non-emission. 4bbl.
750 CFM UNIVERSAL STREETPERFORMANCE CARBURETORS
STREET PERFORMANCECARBURETORS
DESCRIPTION PART NO.750 CFM, classic finish 0-3310C750 CFM, shiny finish 0-3310S
750 CFM, with Ford A/T kickdown lever, includingchrome fuel line kit, shiny finish
0-80508S
Calibrated for small displacement V-8’s or 6 cylinders. Electric choke. Singlefeed/side hung float bowls. Universal throttlelever, vacuum secondaries. Non-emission.
DESCRIPTION PART NO.390 CFM 0-80507-1650 CFM 0-80541-1
650 CFM, shiny finish 0-82651750 CFM, four corner idle, street or strip 0-80528-1
950 CFM, with dual feed DOMINATOR fuel bowls 0-80496-11000 CFM 0-80514-1
COMPETITION DOMINATOR CARBURETOR
Dual feed float bowls. “Soft” progressive linkage. Dual 50cc accelerator pumps. Four corner idle system.Intermediate idle system. Brass floats. Dichromate finish.
DESCRIPTION PART NO.1050 CFM, dual 4 bbl. setups 0-9375-1
1050 CFM, single 4 bbl. setups 0-8082-11050 CFM, alcohol, single 4 bbl. setups 0-80586
1050 CFM, 4bbl. with conventional (short) boosters 0-8896-1
RACE SERIES CARBURETORS
DESCRIPTION PART NO.650 CFM , Mech Secondary 67199750 CFM, Mech Secondary 67200850 CFM, Mech Secondary 67201950 CFM, Mech Secondary 67202
High-performance Race-Series, hand assembled in the U.S.* Utilizes the Proform carburetor high-flow main body* Adjustable, screw-in air bleeds and high-performance down-leg boosters* Maximum air flow: no air horn, choke tower, or choke control* Centered on Proform billet throttle base plate* Adjustable secondary air flow cam bracket and welded throttle shaft* Button torx head throttle plate screws* Power valve blow out protection and slip link mechanical secondary linkage* Assembled with Proform billet metering blocks* Changeable idle feed restriction
CARBURETOR MAIN BODIESDirect Replacement Components to turn astreet carburetor into a high-performance carb.
DESCRIPTION PART NO.Holley® 650 CFM (#4777) and 750 CFM (#4779)
Double Pumper® with Mechanical Secondary67100C
Holley® 750 CFM (#3310) Vacuum Sec. Carburetor 67101C
Features billet–aluminum metering blocks, billet aluminum baseplateswith "Idle-Eze", large capacity fuel bowls complete with patentedsight glasses and patented, streamlined air entries.
MIGHTY DEMON
Ideal for muscle cars, stock rebuilds, tow trucks, mild performanceapplications and crate motors. They are designed for engines withcam profiles between 220 and 240 degrees duration at 0.050".
SPEED DEMON
MIGHTY DEMON
PART NO CFM STYLE BOOSTER
5402010GC 750 Mechanical secondary downleg
5402020GC 750 Mechanical secondary annular
5563010GC 850 Mechanical secondary downleg
SPEED DEMON
1282010 650 Mechanical secondary downleg
1282010VE 650 Vacuum secondary downleg
1402010 750 Mechanical secondary downleg
1402010VE 750 Vacuum secondary downleg
1563010 850 Mechanical secondary downleg
Fuel13v4o_Layout 1 10/31/13 2:17 PM Page 78
83FU
EL DELIV
ERY
Includes the Following:• Manifold Absolute Pressure Sensor(MAP) • Coolant Temperature Sensor (CTS)• Air Temperature Sensor (ATS ) • Throttle Position Sensor (TPS)In each kit you receive every sensoryou’ll need to make the total conversion from carburetor to EFIwith one simple part number.
DESCRIPTION PART NO.Ford 3 Bar / 43.5psi 307051
FORD 3 BAR / 43.5PSI SENSOR KIT
Stop guessing and start tuning foradditional horsepower and reliabilitywith the new FAST Dual SensorAir/Fuel Meter.• Dual wide-band O2 sensorsmeasure air/fuel ratio in both enginebanks simultaneously or averagethem together for precise tuning of
carburetor jetting or EFI profiles• Features include built-in data logger with on-screen playback (no
laptop required), outputs for external data loggers & digital gauges anda narrow-band simulator function
• Built-in calibration and quick start-up deliver A/F readings in under aminute; kit comes complete with everything needed
• Lighted, full graphical display makes it the easiest to use unit available;perfect for race, street and dyno-cell applications
DESCRIPTION PART NO.Air/Fuel Meter, 2 Sensors 170402O2 Sensor, 5-wire, Each 170408
DUAL SENSOR WIDE BAND AIR/FUEL METER
PART NO. DESCRIPTION650HO 650 CFM Performance Carb750HO 750 CFM Performance Carb850HO 850 CFM Performance Carb950HO 950 CFM Performance Carb1050HO 1050 CFM Performance Carb
CUSTOM CARBURETORSHO-Series was designed with the Pro-Street HO seriesand bracket racer in mind. Features clean idle, crispthrottle response & killer acceleration for single 4 bbl.
PART NO. DESCRIPTIONPC3225 850 CFM Carb Base Plate
PART NO. DESCRIPTIONPC3226 850 CFM Carb Center Body
CARBURETOR CENTER BODYDesigned for absolute flow and fuel delivery,Procomp center bodies will help you leavethe competition in the dust. Gain 25-35hpwith this direct replacement, 100% new highperformance carb main bodies. Easy swap in,swap out installation utilizing existing meter-ing blocks, fuel bowls and base plates. Flows850 cfm, adjustable screw in air bleeds, highperformance down leg boosters. Get maximum air withno air horn choke tower, or choke control. Compatiblewith Holley and Proform carb parts. Designed forabsolute performance. 1.750 Venturis.
CARBURETOR BASE PLATEProcomp carb base plates are madewith the highest quality products toprovide top performance. Can be com-bined with our other Procomp carbparts or with high performance carbparts from other manufacturers.Compatible with Holley and Proform carb parts.Designed for absolute performance. 1.750 Venturis.
PART NO. DESCRIPTION113001 Wide-Band, Dual Channel114001 Wide-Band
WEGO IV DUAL CHANNEL WIDE-BAND AFR (AIR/FUEL RATIO) TUNING AIDVersatile tuning aid for all carbureted andfuel injected engines displays AFR (air/fuelratio) and logs over 2 hours data includingtwo channels of AFR, engine RPM, and aspare 0-5V analog input for sensors such asthrottle position or manifold pressure.). WEGOIV Wide-band Exhaust Gas Oxygen Sensor Kit (includes WEGOIV unit, Bosch LSU 4.2 oxygen sensor, 96” sensor extensioncable, 18 x 1.5 mm weld nut for exhaust pipe, USB cable, andsoftware on CDROM)
113001
PART NO. DESCRIPTION118001 TC-1 Turbo Controller
(for automotive applications. Includes USB cable and software on CDROM)
118002 Boost Control Solenoid Valve(for use with TC-1)
TURBO CONTROLLER & BOOST SOLENOIDThe TC-1 is a flexible turbo control systemadaptable to most turbocharged vehicles. Itfeatures a 4-bar MAP sensor and bright LCDdisplay readable in all lighting conditions. TheTC-1 can operate in both open and closed loopcontrol modes with programmable duty cycleor boost curves based on RPM, vehicle speed and or time. The TC-1 includes data logging, built-in USB interface, and Windows soft-ware for programming, data charting, and analysis.
118001
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 83
84FU
EL D
ELIV
ERY
VACUUM LINE CAP KITVinyl. Package of 30.
PART NO.41090
VACUUM LINE CAP KITConvenient kit provides a quick,sure way to seal vacuum lineconnections when vacuum lines havebeen removed. Vinyl. Package of 30.
PART NO.11100
VACUUM CAP ASSORTMENT Quality “Buna-N” rubber makesfor a much more durable, long-lasting part as compared to neo-prene or vinyl materials, especially when exposed tohigh under-hood temps. Includes 4 of 1/8”, 4 of 3/16”,4 of 1/4”, 2 of 5/16", and 2 of 3/8" in each assortment.
PART NO.3704
PART NO.R9009
PART NO.11200
VACUUM CAP ASSORTMENTEPDM Rubber
DESCRIPTION PART NO.1/2'' 380121/4'' 380143/8'' 380385/8'' 38058
ADEL CLAMPSPackage of 6
MOUNTING CLAMPSInsulating with Adel 75005 compound means easier mounting of wire, fuelhose, etc., to any solid surface. Aircraft quality materials used. 6 per set.
DESCRIPTION PART NO.3/16" Inside Diameter 3770G3/8” Inside Diameter 3772G1/2" Inside Diameter 3773G9/16" Inside Diameter 37745/8” Inside Diameter 3775G
CARB DRAIN CUPEasy way to prevent fuel spillage while servicing yourcarburetor. Blue, Plastic, channeled handle. Each.
PART NO.65805
DESCRIPTION PART NO.Fits all 4150/4160 Holley carburetors 11741
Dominator - fits all 4500 Holley series carburetors 11745
PLASTIC CARBURETOR CAPS
CARBURETOR CAPPolyethylene, fits carburetors with5-1/8” diameter neck.
DESCRIPTION PART NO.Carburetor cap 6413
Plastic Dust Cover.
DESCRIPTION PART NO.
Fits Holley Thermoquad/Quadrajetw/5-1/8” Dia. Neck
65802
Fits Holley Dominators w/7-5/6” Dia. Neck
65803
CARBURETOR CAPS
CARBURETOR CAPPlastic, 5-1/8-inch Neck
DESCRIPTION PART NO.Carburetor cap R2012
VACUUM LINE PLASTIC CAP KIT
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 84
85FU
EL DELIV
ERY
Contains gaskets, new pump, diaphragm, new needle and seat, new powervalve, float gauges and a detailed instruction sheet.
PERFORMANCE CARBURETOR RENEW KITS
Trick kits have instructions and all parts needed to modify or rebuild popularHolley carburetors. Each kit includes gaskets, O-rings and othermiscellaneous pieces needed for rebuilding, plus high flow needle and seatassemblies, vent baffles, high capacity power valves, pump cam assortmentand an assortment of secondary springs, if needed.
PERFORMANCE CARB TRICK KITS
MODEL NO. CARBURETOR PART NO. KIT PART NO.
2300 0-4412, -1, -2; 0-7448; 0-84412; 0-87448
37-933
4150 0-3310-1; 0-9188; 0-80436 37-933
4150 0-4776, -1, -2, -3, -4; 0-4777, -1, -2, -3, -4; 0-4778, -1, -2, -3, -4; 0-4779, -1, -2, -
3, -4, -5, -6; 0-4780, -1, -2, -3, -4; 0-6109; 0-8156; 0-9379; 0-80776;
0-80777; 0-80778; 0-80779; 0-80780;0-84776; 0-84777; 0-84778; 0-84779;
0-84780
37-933
4160 0-1848-1; 0-1849; 0-1850-2, -3, -4; 0-4452-1; 0-6619-1; 0-6909; 0-6919;
0-6979, -1; 0-6989; 0-7009-1; 0-7985; 0-7986; 0-7987; 0-8004;
0 8005; 0-8006; 0-8007; 0-9834, -1, -2,-3; 0-80431; 0-80432; 0-80450; 0-
80451; 0-80452; 0-80453; 0-80454; 0-80457, -1; 0-80460; 0-81850; 0-89834
37-933
4160 0-3310-2, -3, -4; 0-80508; 0-83310, -1;0-83311; 0-83312
37-933
MODELNO.
CARBURETOR PART NO. KIT PARTNO.
2300 0-4412, -1, -2; 0-84412 37-4742300 0-4782; 0-4783 37-15374010 0-84010, -1, -2, -3; 0-84011, -1, -2, -3; 0-84020
-1 -2, -3; 0-84035, -1, -2; 0-84047, -137-1541
4011 0-84014, -1, -2, -3; 0-84015, -1,-2, -3; 0-84021-1, -2, -3 37-1541 4150 0-4776, -1, -2, -3, -4; 0-
4777, -1, -2, -3, -4; 0-4778, -1, -2, -3, -4; 0-4779, -1,-2, -3, -4, -5, -6; 0-4780, -1, -2, -3, -4; 0-4781, -1, -2,-3, -4, -5; 0-4788, -1; 0-6109; 0-8156; 0-8162; 0-
8804; 0-9379; 0-9380; 0-9381; 0-80776; 0-80777;0-80778; 0-80779; 0-80780; 0-80781; 0-84776; 0-
84777; 0-84778; 0-84779; 0-84780; 0-84781
37-485
4160 0-1848-1; 0-1849; 0-1850, -2, -3, -4; 0-4452-1;0-4548; 0-6291; 0-6520; 0-6909; 0-7053-1; 0-7154;
0-7413; 0-80431; 0-80432; 0-80457, -1; 0-81850
37-119
4160 0-3310-2, -3, -4; 0-80508; 0-83310, -1; 0-83311;0-8331237-754
37-754
4160 0-6619-1; 0-8007; 0-9834, -1, -2, -3; 0-89834 37-7204165 0-6210-1, -2, -3; 0-6211, -1; 0-6262; 0-6468-1 -2;
0-6497; 0-6498; 0-6512; 0-6528; 0-6711; 0-6772;0-6773; 0-6774; 0-6853; 0-7054
37-605
4165 0-6212; 0-6213; 0-6499; 0-6710; 0-6910 37-15374175 0-7002-1; 0-8276; 0-8302; 0-8546; 0-8679;
0-8700; 0-887937-1537
4175 0-7004-1, -2; 0-7005-1, -2; 0-7006-1, -2; 0-7351;0-7397; 0-7855; 0-8059, -1; 0-8060, -1; 0-9895;
0-9923; 0-9948; 0-9976; 0-80128; 0-80139;0-80155; 0-80169; 0-80491
37-1537
4150 R75010, R75011, R80340, R80340-1,Marine Application
37-1539
4360 R7454, R7455, R7456, R7555 37-1540
“ULTIMATE” CARBURETOR KITSContains every possible add-on feature.Contains only the highest quality components.
PART NO. APPLICATION2300 350-500 CFM Holley 2-Barrel Kit4150 390-1000 CFM Holley Double Pumper Kit
4150A Same As 4150 Alcohol Compatible4160 600-950 CFM Holley Vacuum Secondary Kit4190 Carter 9000, Edelbrock Performer4500 750-1250 CFM Holley Dominator Kit
CARBURETOR REBUILD KITIncludes all parts and gaskets necessary torebuild Edelbrock Performer Series carbs.
DESCRIPTION PART NO.Performer Series Rebuild Kit 1477
Five kits service all Holley per-formance carburetors. Usesgenuine Holley quality serviceparts. Explicit step-by-stepinstructions. Includes detailedtuning guide. Packaging serves as a handy parts tray.
F.A.S.T. KITS
DESCRIPTION PART NO.Fits Model 4160 4 Barrel 37-1542Fits Model 2300 2 Barrel 37-1543
Fits Model 4150 4 Barrel Double Pumper 37-1544Fits Model 4150HP 37-1546
Fits Model 4500 Dominators 37-1547
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 85
86FU
EL D
ELIV
ERY
Engine Works carb overhaul kits are designed to meet thedemands of high performance applications. All components meetor exceed factory specifications. Kit includes precision gasketsand seals, needle and seat assemblies, accelerator and vacuumsecondary diaphragms.
DESCRIPTION PART NO.
Fits Holley 4160 390, 450, 600, 750 & 850 CFM carbs 11419
11419 with reusable gaskets 11419R
Fits Holley 2300 2 bbl. 11474
11474 with reusable gaskets 11474R
Fits Most Holley double pumper carbs 11485
11485 with reusable gaskets 11485R
11419 11419R
11474
1148511485R
11474R
CARBURETOR MOUNTING GASKETS
PART NO. APPLICATION49 Holley 2-bbl
54 Carter, AFB, Holley Open Center
55 Carter, AFB Holley 4-port
56 Quadrajet
56A Quadrajet Open Center
58B Dominator, 4-port
58C Dominator, Open Center
Engine Works is the place for value in carburetor components. Onlythe highest quality parts are accepted, designed and specified forEngine Works by OEM engineers and aftermarket carb modifiers.
49
55
56A58B
58C
56
54
Two each Teflon coated fuel bowland metering block gaskets.
CARBURETOR GASKET KIT
FUEL BOWL GASKETS
METERING BLOCK GASKETSEACH 4-PK. APPLICATION
129 11829 Fits 4150 series
130 11830 Fits 4160 series secondary
131 11831 Fits 4160 series primary
CARBURETOR OVERHAUL KITS
DESCRIPTION PART NO.4160 Reusable - Each 133
4160 Reusable - 4-Pack 118334500 3 Circuit - Each 135
4500 3 Circuit - 4-Pack 11835
PART NO.11800
APPLICATION PART NO.Black, Buna-N, Pair Prim/Sec 4500, Pair 108-36-2
Primary 4180, Pair 108-55-2Blue, Buna-N, Non-Stick,
secondary double pumper 4150, Pair108-89-2
Blue, Buna-N, Non-Stick, Prim/Sec 4165/4175, Pair 108-91-2Black, Buna-N, Sec 4160, Pair 108-27-2
METERING BLOCK GASKETS
APPLICATION PART NO.Fuel bowl inlet fitting gasket, 7/8”, pkg. of
2, center hung 108-8
Holley 4500/ King Demon, Pair 108-120Metering Block, Blue Reusable Fiber, Pair 108-121
Standard Replacement Paper Gasket 8 pack 108-2-20Fuel Bowl Gasket 108-56-2
Fuel Bowl, Holley 4150/ Claw/ Demon, Pair 108-83-2Blue, Buna-N, Non-Stick, Metering block, Pair 108-90-2
Fuel Bowl, Holley 4150/ 4160/ 2300,Primaries, Blue Non-Stick, Pair
108-92-2
Fuel Bowl, Metering Block, Blue ReusableFiber, Set of 4
108-200
FUEL BOWL GASKETS &METERING BLOCKS
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 86
87FU
EL DELIV
ERY
CARBURETOR ADAPTERS & ADAPTER PLATESDESCRIPTION PART NO.
Mounts square-bore Holley carb to spread-boreEdelbrock intakes, except #2101/3701 (1/16" thick)
2732
.850” Thick, Quadrajet adapter plate, MountsEdelbrock square-bore carb to stock Quadrajet
and Thermo-Quad manifolds.
2696
CARBURETOR ADAPTER KITSIncrease your car’s overall perform-ance by updating to the latest highperformance carburetors without pur-chasing costly intake manifolds. Gaskets,studs, nuts and washers are included. Madeof die-cast aluminum.
DESCRIPTION PART NO.
Adapt any 4-bbl. carburetor to any 4-bbl. manifold (exceptHolley 4500 and OEM manifolds with exposed exhaust
crossover tubes) Adapter only, 3/4” nominal height.
1932
Adapts any 4-bolt, 4-bbl. to any small 4-bolt, 2-bbl.manifold and/or any 4-bolt, 2-bbl. to any 4-bolt, 4-bbl. manifold (except spread bore) Adapter only,
1” nominal height.
1933
Adapts Holley 350/500 CFM 2-bbl. carburetor to Quadrajetbolt pattern. Adapter only, 1-1/8” nominal height.
1929
Adapts large Holley 2-bbl. to any Rochester 4-bolt,2 bbl. base or any Rochester 4-bolt, 2bbl. carb to
large Holley 2-bbl.base.
1937
DESCRIPTION PART NO.4-Hole square bore, 1/2” thick 3710
CARB HEAT SHIELDHelps eliminate fuel boiling and vaporlock caused by heat conducted fromthe manifold to the carb.
DESCRIPTION PART NO.4-Hole, Square Bore/Spread Bore, .875 in. tall 2034
Open Center, Dominator/Square Bore, 2 in. tall 2281
Designed to allow you to mountmost any carburetor on most any manifold, to save you the expenseof buying a different manifold or carburetor. Made from high-qualitycast aluminum, these adapters provide a smooth transition fromcarb to intake for trouble-free operation.
CARB ADAPTERS
2281
2732
PART NO. APPLICATION
3-200 Rebuild Kit NS (4160 V.S.)3-201 Rebuild Kit N/S (2300)3-202 Rebuild Kit N/S (4150 D.A.)
3-203 Rebuild Kit N/S For (4500)
3-204 Rebuild Kit N/S (4150/4150 HP)
3-205 Rebuild Kit N/S (4150 HP/DP)
3-206 Rebuild Kit (4165/4175)
3-207 Rebuild Kit N/S For(4500) Akly
3-208 Rebuild Kit N/S (E-85& ALKY)
3-210 M2300/4150 Service Pack NS
3-213 M4500 Service Pack Non Stick
3-300 Super NS Rebuild Kit (4160 VS)
3-301 Super NS Rebuild Kit For M2300
3-301C Carburetor Center Kit
3-301E Carburetor End Kit
3-302 Super Rebuild Kit
3-303 Super NS Rebuild Kit For M45003-304 Super NS Rebuild Kit3-305 Super NS Rebuild Kit
CARB REBUILD KITS
CARBURETOR ADAPTER
DESCRIPTION PART NO.Holley/AFB 4BBL to Q-Jet Base R2066
Gasket & Hardware Included
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 87
88FU
EL D
ELIV
ERY
PART NO. APPLICATION43240 BG Demon™ carb to 06AN43241 BG Demon™ carb to 08AN43245 Holley™ carb to 06AN43246 Holley™ carb to 08AN43250 Holley™ Dual Feed fitting 06AN43251 Holley™ Dual Feed fitting 08AN
Engine Works aluminum fittings areproduced to aerospace specs to pro-vide the ultimate in quality sealingyour fuel system connections.
CARB ADAPTERS & FITTINGS
43246
43250
DESCRIPTION PART NO. #6 AN Fitting for Edelbrock Perf. Series Carbs
(5/8"-20)8087
CARB INLET FITTING
DESCRIPTION PART NO.Inlet Fitting, 7/8-20 x 3/8"
Inverted Flare11626
INLET FITTING
Tapered fittings have one side cut off and the inside radiused for flow.Each requires an O-ring for sealing into port. Tapered reducer fittingsare cut off on the larger side only.
DESCRIPTION PART NO.-8 AN to -6 AN 15605-6 AN to -6 AN 15606-8 AN to -8 AN 15607
-10 AN to -10 AN 15608-10 AN to -8 AN 15610
TAPERED FLARE FITTINGS
Machined from solid aluminum. Will notwarp. Features changeable idle feed restriction.
DESCRIPTION PART NO.Billet Metering Block 67150C
BILLET METERING BLOCK
TBI SPACERTBI Adapter, 2-bbl Pro-Jection.
DESCRIPTION PART NO.Spread bore to TBI flange 17-41
DESCRIPTION PART NO.1986 - 93 5.0L Mustang 10601
The complete Fuel Rail Kit includesadjustable pressure regulator (or stock regu-lator) as well as fittings that allow connection of the stock inlet andreturn lines. These kits will also fit 54126/54127 manifolds for 351W.Fits: 1986 - 93 5.0L Mustang. *This kit can be used on a 1994 - 955.0L engine if a smaller diameter aftermarket distributor is used.
POWERFLOW FUEL RAILS
FUEL RAILSBillet Aluminum, Red Anodized, Pair.
PART NO. APPLICATION14101 Ford Mustang
HIGH PERFORMANCE FUEL RAIL KITSMore Volume = More Horsepower!• The ultimate lightweight design• Complete with mounting brackets and stainless steel hardware• Includes Viton O-rings and custom-made tapered fuel fittings
PART NO. APPLICATIONSCP7000LS1 Chevrolet LS1
SCP7001 Small Block Chevy *SCP7002 Big Block Chevy *SCP7003 Small Block Ford *SCP7004 4.6L Modular Ford *
* Designed to work with aftermarket, single plane intake manifolds.Not for stock intake manifolds.
TAPERED FUEL FITTINGS
DESCRIPTION PART NO.#8 O-Ring to #6 Male Flare SCPFRF#6#8 O-Ring to #8 Male Flare SCPFRF#8
Fuel13v4o_Layout 1 10/31/13 2:18 PM Page 88
89FU
EL DELIV
ERY
DESCRIPTION PART NO.Holley Quad - 9-5/16 in. Centers, Push-on fitting R2197
Holley with Dual Metering Blocks,9-5/16 in. Centers, NPT fitting
R2197X
Holley Quad Model 3310 - 8-21/32 in. Centers,Push-on fitting
R2198
Holley Carb 3310-2 - 8-21/32-inch Centers R2198X
DESCRIPTION PART NO.Dual-inlet Holley 4-bbl. (3/8" tube, 8-21/32"
centers)1551
Dual-inlet Holley 4-bbl. (3/8" tube, 9-5/16"centers)
1552
Line w/Fuel Pressure Gauge fits Holleyw/8-21/32” centers
1558
Line w/Fuel Pressure Gauge9-5/16” centers
1559
Race, Speed & Road Demon Carburetors 1575Adjustable fits Holley 4150/4160 w/red and
blue hose ends1556G
CHROME GAS LINE KIT Add a “touch of class” to your engine with these chrome-platedgas line kits. Constructed with copper tubing, brass fittings andsilver brazed connections. The “hex” design provides wrench-ing area for easier installation of fittings.
CHROME FUEL LINES
CHROME DOUBLE PUMPER FUEL LINEFeatures 1/8” tap to accept fuel pressure gauge.Designed for Holley carburetors with a 9-5/16”center.
FUEL LINESNo bending required. Special flares on carb end for improvedsealing. 3/8” diameter tubing provides excellent fuel flow.
DESCRIPTION PART NO.Holley Quad (9-5/6” centers) 2197
PART NO.52197
PART NO.34-150
FUEL LINE KITChrome, Steel, Holley 4150,5/8” NPY Inlet, 1/8” NPTGauge Port.
2197X
DUAL FEED CARBURETOR LINESOur stainless braid hose is rated at 1000 psi, is imperviousto fuels and will withstand temperatures to 300˚ F.Made better in the USA!
43145 53139
43142
PART NO. APPLICATION COLOR
43139 Holley 4150 - 06AN Red/Blue43140 BG Demon - 08AN Red/Blue43141 Holley 4150 - 08AN Red/Blue43142 Holley 4150 - 08AN - Push Lock Red/Blue43145 Holley 4500 - 08AN Red/Blue43146 Dual Feed Ultra HP Carb Kit 6AN Red/Blue43147 Dual Feed Ultra HP Carb Kit 8AN Red/Blue
PART NO. APPLICATION COLOR53139 Holley 4150 - 06AN Black43140 BG Demon - 08AN Black53141 Holley 4150 - 08AN Black53142 Holley 4150 - 08AN - Push Lock Black53145 Holley 4500 - 08AN Black53146 Dual Feed Ultra HP Carb Kit 6AN Black53147 Dual Feed Ultra HP Carb Kit 8AN Black
RED/BLUE
BLACK
53142
DUAL FEED LINE ASSEMBLIES
Completely assembled and ready to use.
DESCRIPTION PART NO.
Fits 800 & 850 cfm Holley 4150, -6 AN inlet FCP 0101
Fits 800 & 850 cfm Holley 4150, -8 AN inlet FCP 0134
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 89
90FU
EL D
ELIV
ERY
ALUMINUM FUEL LINE
Large Diameter, Lightweight,Legal in all classes.
DESCRIPTION PART NO.25’ Coil, 3/8” O.D. 6533025’ Coil, 1/2” O.D. 65340
‘Y’ FITTINGS
The only true one-piece ‘Y’ fittingdesign. They will not fail. CNC-machined from one-piece 6061- T6 billet Hard-anodized coating is compatible with alcohol, exotic fuel-additives, water and oil
DESCRIPTION PART NO.#10 Single #8 double MP-6208#12 Single #10 double MP-6220#8 Single #6 double MP-6286#12 Single #8 double MP-6228
Y-BLOCKS
Join or split fuel lines for a neat installation withminimal flow loss.
DESCRIPTION PART NO.#8 Single #6 double MP-6160
FUEL LOGS
Designed to configure multipleRegulators with less restriction and evenfuel distribution. All ports are #10 AN.
DESCRIPTION PART NO.Double fuel log MP-7600-02Triple fuel log MP-7600-03
ALUMINUM FUEL LINE TUBINGAluminum tubing is seamless, .035” wall wound in 25 foot coils.100% current tested for safety. Comes in natural color.
DESCRIPTION PART NO.UNIVERSAL FUEL LINE & FILTER KIT
Polished Aluminum Filter 8131Blue Anodized Aluminum Filter 8134
STAINLESS LINES (FROM FILTER TO PUMP)Small Block Chevy 8123
FUEL LINE & FILTER KITEdelbrock’s Fuel Line & Filter Kit, designed for Performer Series carbs,includes a hard chromed steel line and Russell fuel filter. Our convenientPre-Fitted Stainless Lines connect the fuel filter to an Edelbrock streetfuel pump or any pump with 3/8" NPT outlet. The Chromed Steel FuelLine is available with a 3/8" barbed end and no fuel filter for universalapplications.
DESCRIPTION PART NO.25’ Coil, 3/8” Diameter 5203825’ Coil, 1/2” Diameter 5201225’ Coil, 5/8” Diameter 52058
CHROME STEEL FUEL LINE3/8'' Barbed Hose End Inlet
(Does not include fuel filter).Designed for Performer & Thunder Series Carburetors
PART NO.8126
FUEL BLOCK KIT
Allows Equal Flow. For multi carburetorapplications. Aluminum.
DESCRIPTION PART NO.“T” Fuel Block Kit 1557
Fuel Block w/Fuel Pressure Gauge 1-1/4 in., 0-15 lbs. 1560“Y” Fuel Block Kit 2961
“T” Style Fuel Block Triple Outlet 6151
ALUMINUM FUEL BLOCK KITSIncludes a 1/8" NPT provision for a fuel pressure gauge and a sock-et head pipe plug if a gauge is not used.
DESCRIPTION PART NO.1/2" Hose Inlet with Two 3/8" Hose Outlets 651601/2” Hose Inlet with Two 1/2” Hose Outlets 65170
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 90
91FU
EL DELIV
ERY
SURE SEAL SPACERS WITH O-RING SEALEnjoy the benefits of straightening out the air flow to the carburetorventuri plus the confidence of an O-ring seal for your breather/filter.Available in 1” and 1/2” heights. Brushed aluminum.
DESCRIPTION PART NO.1/2” Sure Seal spacer 511051” Sure Seal spacer 51110
INSULATING PLASTIC & PHENOLIC CARBURETOR SPACERS & ADAPTERSAdvanced plastic and phenolic compounds are specially formulated toreduce heat conductivity 10 times greater than aluminum. Reducingfuel temperature inside the carburetor results in a denser, more power-ful fuel charge to the manifold. Insulating phenolic spacers come pre-drilled for alignment pins and include all mounting hardware. Gasketsnot included.
DESCRIPTION PART NO.4-Hole Plenum Design w/1.75" Dia. Bores, 1"
Thick, 4150/4160 Carb64930
Open Plenum Design, 1" Thick, 4150/4160 Carb 649404-Hole Plenum Design w/1.75" Dia. Bores, 1/2"
Thick64943
Open Plenum Design, 1/2" Thick, 4500 Carb 64947Carb Adapter Kit, 2-Hole Plenum, 1” thick 64949
4500 Cast Aluminum, Open Plenum, 1” thick 649504500 Billet Aluminum, Open Plenum, 1” thick 64951
Billet Alum. Carb Adapter, 2-Hole Plenum, 1/2”thick, 1.693 Dia. bores
64966
Cast Aluminum Carb Adapter 4500 Carb to4150/4160 Manifold
65000
Wood, 4150/4160, 1/2” thick, Open Plenum 65015Wood, 4500, 1/2” thick, Open Plenum 65016
Wedge Plate fits standard Holley bolt pattern 65030
CARB AIR PAN KITS
Air pan-to-hood sealing ring is manufac-tured of fire retardant foam. Pans Measure 12” x 24”.
DESCRIPTION PART NO.Single 4-bbl, Holley w/ 5/8” neck 65960
Single 4-bbl, Holley 4500, Dominator w/7-5/16” neck 65961
FUEL BOWL INLET FITTING GASKET
DESCRIPTION PART NO.Size 7/8” nylon 26-102
ASSORTED FITTINGS
DESCRIPTION PART NO.Swivel Fitting, Hose
5/16”, Thread 9/16”-2426-25
Aluminum Red AnodizedPlug 7/8”-20
26-76
DESCRIPTION PART NO.Cast Aluminum, Holley 1-inch tall with PCV Fitting
w/3 in. stud kit and 3/8 in vacuum tubeR2103
1-inch, Phenolic, 4-Hole, Gaskets Included R91342-inch Phenolic with 4-Hole Design (Gaskets Included) R9135
1-inch, Phenolic, Open Center, Gaskets Included R91362-inch Phenolic Open Center (Gaskets Included) R9137
1/2-inch Phenolic with 4-Hole Design (Gaskets Included) R91381/2-inch Phenolic Open Center (Gaskets Included) R9139
Holley 2-inch Open Port R2081Holley 1-inch Tall Carburetor Spacer with PCV Fitting R2103
CARB SPACERS
R2103 R9134
PHENOLIC THERMAL INSULATING CARB SPACERSDesigned to insulate and reduce heatflow to the carb keeping it cooler allowinga denser fuel mixture to enter the engineand produce more horsepower. Includesgaskets, studs, nuts and washers.
3404
DESCRIPTION PART NO.1" 4-Hole bore 34041" Open center 3405
1” 4-Hole Quadrajet 3406
ALUMINUM CARB SPACER KITSDesigned to fit the standard Holley/Carter boltpattern. Precision die cast aluminum spacerkits are complete with studs, washers, nuts,and gaskets. The one inch open center spacer#6005 features a 1/4” diameter knock-out holeif an additional vacuum port is required.
DESCRIPTION PART NO.1" Open center 6005
1” Ported 60062” Open center 6007
Aluminum 1” Open Center w/ 3/8” PCV tube 4945
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 91
92FU
EL D
ELIV
ERY
VELOCITY AIR CARB SPACERSOne or two inches of pure horsepower! The V.A.C. Spacer is designed to channel the intake signalthrough the plenum area to the maximum positive area of vacuum created in the runner. By doingso, fuel atomization is balanced among air molecules to form a consistency among the intake pulsesresulting in a smoother powerband for the engine. If all that sounds too technical, how about this -dynos prove 10 to 15 horsepower gains in one easy bolt on! Designed by HVH (High Velocity Heads).
ALUMINUMLIGHTWEIGHT ALUMINUM
1'' Four Hole4150/4160 Holley
1'' Four Hole4150/4160 Holley
2 Barrel 2 Hole4412 Holley
PLASTIC
41651
41645
41649
2'' Four Hole4150/4160 Holley
2'' Four Hole4150/4160 Holley
41652
2'' Four Hole4500 Holley
416481'' Four Hole4500 Holley
4164641647
2'' Four Hole 4500 HolleyAdapter to 4150 Manifold
41653
INSULATING PHENOLIC SPACERS
Racers love advanced GE phenolic material because of its insulating qualities. Phenolic transfers 10 times less manifold heat to the carburetor,resulting in cooler, more dense fuel charges.
1'' Holley 4150/4160Standard Open Plenum
416011'' Holley 4-hole, 4150/4160 1.775'' Bore Plenum
416051'' Holley 4500Standard Open Plenum
416022'' Holley 4500Standard Open Plenum
41603
1'' Two Hole Slider Intake Spacer Kit
41610
1/2'' GT40 EFI Without EGR Intake Spacer Kit
41621
INTAKE SPACERS
2'' Holley 4150Standard Open Plenum
- Transfers cooler and more dense fuel/air mixtures- Designed for maximum undisturbed air flow- 15 HP increase over standard 1" open spacer!
PART NO. DESCRIPTION MODEL CFM HEIGHT41611 Outlaw Phenolic Carb Spacer 750 4150 750 1”41612 Outlaw Phenolic Carb Spacer 850 4150 850 1”41615 Outlaw Phenolic Carb Spacer 4500 Cloverleaf 4150 Cloverleaf 1”41616 Outlaw Phenolic Carb Spacer 1050 4500 1050 1”41617 Outlaw Phenolic Carb Spacer 1150 4500 1150 1”41618 Outlaw Phenolic Carb Spacer 1250 4500 1150 1”
41604
OUTLAW SERIES POWERFLOW PHENOLIC SPACERS
SHEAR PLATES
DESCRIPTION PART NO.1/2" Holley 4150
Shear Plate550300
2.000" Bore Holley 4500Style Shear Plate
550301
2.125" Bore Holley 4500Shear Plate
550302
Engine Works carburetor shear plates aredesigned to direct incoming air to efficientlydevelop more power and torque. They improveair/fuel distribution by increasing plenum areaand broadening the horsepower range. EngineWorks carburetor shear plates are quality madefrom high-quality billet aluminum with ananodized finish for durability and corrosionresistance and great looks.
550300
41618
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 92
93FU
EL DELIV
ERY
HELI-COIL INSTALLATION TOOL KIT
Includes gaskets and screws.
DESCRIPTION PART NO.0-3310 or most 4160 w/center hung float bowl 34-13
Holley 4160 5/8”-18 inverted flare inlet. 8-21/32” center to center
34-6
METERING BLOCK KIT
Contains inserts and tapsNote: requires 15/64” drill bit.
ALCOHOL JETS
DESCRIPTION PART NO..132 122-100.136 122-101.138 122-102.140 122-103.142 122-104.144 122-105
DESCRIPTION PART NO..146 122-106.148 122-107.150 122-108.152 122-109.154 122-110 PART NO.
26-2
Package of 2.
AIR BLEEDASSORTMENT KITCarburetor Air Bleed, Brass, Screw-In, 20-79 Range, 4500 & 4150 Series.
PART NO.36-240
STANDARD MAIN JETS2-ct. pkg., 1/4-32 UNF Thread
DESCRIPTION PART NO..040” 122-40.043” 122-43.045” 122-45.0465” 122-46.048” 122-48.049” 122-50.052” 122-52.052” 122-53.053” 122-54.054” 122-55.055” 122-56.056” 122-57.057” 122-58.058” 122-59.060” 122-60.060” 122-61.061” 122-62.062” 122-63.064” 122-64.065” 122-65.066” 122-66.068” 122-67.069” 122-68.070” 122-69.073” 122-70.076” 122-71.079” 122-72
DESCRIPTION PART NO..079” 122-73.081” 122-74.082” 122-75.084” 122-76.086” 122-77.089” 122-78.091” 122-79.093” 122-80.093” 122-81.093” 122-82.094” 122-83.099” 122-84.100” 122-85.101” 122-86.103” 122-87.104” 122-88.104” 122-89.104” 122-90.105” 122-91.105” 122-92.105” 122-93.108” 122-94.118” 122-95.118” 122-96.125” 122-97.125” 122-98.125” 122-99
JET ASSORTMENTTrack tune your Holley carburetor fortop performance.
JET REMOVAL TOOL
Steel plastic handle, fits all roundstyle jet applications.
AIR BLEED KITS Packs of 10
DESCRIPTION PART NO.HP Dominator, .070 in. 126-70-10
DESCRIPTION PART NO.
1/4” x 32, sizes .64 to .99, 2 of each size 36-181
5/16” x 32, sizes .132 to .200, 4 of each size, alcohol 36-201
PART NO.26-68
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 93
94FU
EL D
ELIV
ERY
CALIBRATION KITSKit includes 1 pair of metering rod retainingsprings and an assortment of metering rods,metering jets and step-up springs in pairs.
APPLICATION PART NO.1405 carb 1479
1407, 1411, 1413 carb 14801403, 1404 carb 1486
1406 carb 14871411 carb 1489
CARBURETOR JETS
High quality carb jets machined to tight tolerances. Availablein packages of 2 or 10.
A very popular option that moves jets further into the float bowl toimprove fuel pickup during hardacceleration. Requires use ofnotched float. Package of 2.
PART NO. DESCRIPTION11250 Main Jet Extensions
MAIN JET EXTENSIONS
2-PACK 10-PACK JET SIZE11220-68-2 11220-68 Size 6811220-69-2 11220-69 Size 6911220-70-2 11220-70 Size 7011220-71-2 11220-71 Size 7111220-72-2 11220-72 Size 7211220-73-2 11220-73 Size 7311220-74-2 11220-74 Size 7411220-75-2 11220-75 Size 7511220-76-2 11220-76 Size 7611220-77-2 11220-77 Size 7711220-78-2 11220-78 Size 7811220-79-2 11220-79 Size 7911220-80-2 11220-80 Size 8011220-81-2 11220-81 Size 8111220-82-2 11220-82 Size 8211220-83-2 11220-83 Size 8311220-84-2 11220-84 Size 8411220-85-2 11220-85 Size 8511220-86-2 11220-86 Size 8611220-87-2 11220-87 Size 8711220-88-2 11220-88 Size 8811220-89-2 11220-89 Size 8911220-90-2 11220-90 Size 9011220-91-2 11220-91 Size 9111220-92-2 11220-92 Size 9211220-93-2 11220-93 Size 9311220-94-2 11220-94 Size 9411220-95-2 11220-95 Size 9511220-96-2 11220-96 Size 9611220-97-2 11220-97 Size 9711220-98-2 11220-98 Size 9811220-99-2 11220-99 Size 9911220-100-2 11220-100 Size 100
JET EXTENSION KIT FOR HOLLEY CARBSEliminates fuel starvation during hard acceleration or cornering by extend-ing the fuel pickup point of the jet farther into the float bowl.
DESCRIPTION PART NO.1/4”-32 , Standard Holley jets 65440
Holley 2 or 4 bbl., pair 652275/16”-32, Holley HP, pair 65441
Jet Removal Tool, Fits Holley round-head jets 62293
AIR BLEED TUNING KITS Kits includes 4 each of 11 air bleeds. Each kitcomes in a handy plastic storage container.
DESCRIPTION PART NO.High Speed System, No. 20-35 67245Idle Speed System, No. 65-75 67246
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 94
95FU
EL DELIV
ERY
POWER VALVES
PART NO. VAC HG 11525 2.5" 11535 3.5"11545 4.5"11555 5.5" 11565 6.5"11575 7.5"11585 8.5”
For Holley 2300, 4150 and 4160 seriescarburetor. No drilling is required for pri-mary side protection. Kit includes thread-ed check valve that installs in existinghole. Includes washer and pins.
PART NO. DESCRIPTION11590 Power Valve Shield
POWER VALVE SHIELD
POWER VALVE BLOCK-OFF PLUG
POWER VALVE BLOCK-OFF PLUG
PART NO. APPLICATION11636 Power Valve Plug
PART NO. APPLICATION26-36 1/2-28 in.
IDLE MIXTURE SCREWAccessible, large head style.
IDLE MIXTURE SCREW GASKETReplacement Cork Gasket (pkg. 10).
NEEDLE AND SEATS
DESCRIPTION PART NO.Needle & Seat Washer Top & Bottom 11502.110” Viton Needle and Seat, 2 pack 11504.110” Viton Needle and Seat, 2 pack 11506.120” Viton Needle and Seat, 2 pack 11508.130” Viton Needle and Seat, 2 pack 11509
.130” SS Needle and Seat, 2 pack 11510
.150” SS Needle and Seat, 2 pack 11511
DESCRIPTION PART NO..110” adjustable 6-500-2.120” adjustable 6-502-2.130” adjustable 6-515-2.150” adjustable 6-519-2
NEEDLE & SEAT HARDWARE KIT
DESCRIPTION PART NO.Contains 1 adj. nut w/gasket,
1 locking screw w/gasket, 1 O-Ring34-7
STEEL INLET NEEDLEMost Holley performance carbs areequipped with “Viton” needle & seat. Ifyou use exotic fuels or additives such asalcohol, benzine or acetone, use a Holleysteel needle and seat. Pair.
POWER VALVE BLOCK-OFF PLUG AND PROTECTORPART NO. DESCRIPTION
1510 Block-off plug for Holley Carbs1511G Protector, fits Holley, 2300/4150/4160
PART NO.26-101
PART NO.26-110-10
1511G1510G
FLOAT KIT Includes 2 floats, 2 pins and a float settinggauge. All EPS carbs.
ACCELERATOR PUMPIncludes accelerator pump, spring andcup assembly.
ACCELERATOR PUMP PLUNGERHigh-Performance Accelerator Pump Plunger & Spring,Shorter Than Standard Street Plungers. Gives AdditionalPump Shot Volume.
PART NO.1470
PART NO.1982
PART NO.1469
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 95
96FU
EL D
ELIV
ERY
VITON INLET NEEDLEMost Holley performance carbs are equipped with “Viton”needle and seat. If you use exotic fuels or additives such asalcohol, benzine or acetone, use a Holley steel needle andseat. Each.
TITANIUM INLET NEEDLE.150” seat. Needle is made of titanium and is respon-sive to flow rate changes.
POWER VALVESIncludes gasket. Each is stamped with a numberto indicate its vacuum opening point.
POWER VALVE CHECK BALLPower valve blowout protection can nowbe added to pre ‘92 model 2300, 4150,and 4160 carburetors. Consisting of aspring, brass seat and check ball, this kitwill effectively protect the power valve andis easy to install. Included is the proper drill bit sizewith stop to facilitate installation.
DESCRIPTION PART NO..110 adjustable 6-504.097 adjustable 6-506
.0785 Non-Adjustable 6-511.097 Off road adjustable 6-513
.120 adjustable 6-518-2
DESCRIPTION PART NO.Titanium Inlet Needle 6-521
ACCELERATOR PUMPInstantaneous response! Pulls strongthroughout the RPM band. Increases thecapacity over standard 30cc pump onHolley Models 2300, 4150, and 4160 carbs.Eliminates flat spots off idle or at any otherRPM range. Includes everything required foreasy installation.
ACCELERATOR PUMP COVERChrome 30cc Pump.
ACCELERATOR PUMP DISCHARGE NOZZLEEach discharge nozzle comes with 2 gaskets.Use on Models 4150, 4160, & 4500, Straight Type.
DESCRIPTION PART NO..021” 121-121.025” 121-125.028” 121-128.031” 121-131.032” 121-132.035” 121-135.037” 121-137
.040” includes hollow pump screw 121-140
.042” includes hollow pump screw 121-142
.045” includes hollow pump screw 121-145
.047” includes hollow pump screw 121-147
.050” includes hollow pump screw 121-150
ACCELERATOR PUMPDISCHARGE NOZZLEIncludes 2 gaskets. Use on 4165 and 4175.Not anti-pullover.
DESCRIPTION PART NO..031” 121-31.040” 121-40.045” 121-45.037” 121-37
DESCRIPTION STD. FLOW HIGH FLOWSingle Stage, 1.0” Hg. 125-10 ---Single Stage, 2.5” Hg. 125-25 ---Single Stage, 3.5” Hg. 125-35 ---Single Stage, 4.5” Hg. 125-45 ---Single Stage, 5.0” Hg. 125-50 ---Single Stage, 5.5” Hg. 125-55 ---Single Stage, 6.5” Hg. 125-65 125-165Single Stage, 7.5” Hg. 125-75 ---Single Stage, 8.5” Hg. 125-85 ---Single Stage, 9.5” Hg. 125-95 ---Single Stage, 10.5” Hg. 125-105 ---
PART NO.125-500
PART NO.20-11
PART NO.34-504
ACCELERATOR PUMP DISCHARGE NOZZLE
DESCRIPTION PART NO.Nozzle Straight Type 021 11260-21Nozzle Straight Type 025 11260-25Nozzle Straight Type 028 11260-28Nozzle Straight Type 031 11260-31Nozzle Straight Type 032 11260-32Nozzle Straight Type 035 11260-35Nozzle Straight Type 037 11260-37Nozzle Straight Type 040 11260-40Nozzle Straight Type 042 11260-42Nozzle Straight Type 045 11260-45Nozzle Straight Type 047 11260-47Nozzle Straight Type 050 11260-50Nozzle Straight Type 052 11260-52
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 96
97FU
EL DELIV
ERY
HOLLEY HIGH FLOWSCREWSRadiused allen head stream linedfor less turbulance and increased air flow. 1 per pkg.
DESCRIPTION PART NO.Notched Float Kit with jet extensions 116-10
Notched Float Kit without jet extensions 116-11
UMBRELLA CHECK VALVESPackage of 2
FLOATS
DESCRIPTION PART NO.Side hung, Nitrophyl 116-1
Side hung, Brass 116-4Center hung, Nitrophyl 116-3
Center hung, Brass 116-2
NOTCHED FLOAT KITA notched float is an absolute necessity whenusing main jet extensions. Designed with"notches" to clear main jet extensions. Thisallows the float to operate normally without thepossibility of interference from the extensions.
FLOAT HANGER HARDWARE KIT
PART NO. DESCRIPTION11355 30cc Pump, 2 pack11357 50cc Pump, 2 pack
ACCELERATOR PUMP DIAPHRAGMS
ACCELERATOR PUMP DIAPHRAGMS
VACUUM SECONDARY DIAPHRAGM
DESCRIPTION PART NO.30cc (rubber), each 135-550cc (rubber), each 135-7
30cc (GFLT) Compatible w/alcohol based fuels 135-1050cc (GFLT) Compatible w/alcohol based fuels 135-9
PART NO.26-41
PART NO.135-4
PART NO.20-105
Will replace your existing worn-out diaphragms. Theyare made from a high-performance rubber material andare designed to fit most Holley carburetors with vacuumsecondaries. Rod length is 2.054"
PART NO. DESCRIPTION65442 Cadmium Plated, Gasoline
ACCELERATOR PUMP CAMAssortment enables selection of proper camto tailor pump requirements to individualengine requirements.
DESCRIPTION PART NO.Holley 2300/4150/4160 20-12
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 97
98FU
EL D
ELIV
ERY
DESCRIPTION PART NO.Drag Race, Individual 65228
Oval Track, Kit 65432
DESCRIPTION PART NO.30cc 5335
FLOATS FOR HOLLEY CARBURETORS
ACCELERATOR PUMP DIAPHRAGM
DESCRIPTION PART NO.Standard .031, pair 5431Standard .035, pair 5435
ACCELERATOR PUMP SQUIRTERS
DIAPHRAGM REPAIR KITHolley 12-803 & 12-804
PART NO.12-807
ACCELERATOR PUMP SPRING50cc. 10 pack
PART NO.20-109-10
65228 65432
SECONDARY DIAPHRAGMSPRING KITColor coded for 7 differentopening rates.
VACUUM SECONDARY HOUSING COVER
SECONDARY CONNECTING ROD
PART NO. DESCRIPTION20-53 4160 / 401020-54 4150 / 4010
PART NO. DESCRIPTION11213 Vacuum Secondary Spring Assortment, 7 sizes11354 Vacuum Secondary Diaphragm
VACUUM SECONDARY ACCESSORIES
STEP-UP SPRING ASSORTMENTIncludes 3"Hg (blue), 4"Hg (yellow), 5"Hg (orange),7"Hg (pink) and 8"Hg (plain) springs. (each in pairs)
PART NO.20-13
PART NO.20-59
PART NO.1464
Quickchange. Allows you to change thesecondary diaphragm spring withoutdisturbing the diaphragm.
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 98
99FU
EL DELIV
ERY
DESCRIPTION PART NO.Chevy, 1977 and Up 8009
THROTTLE CABLE ADAPTER STUD
CARBURETOR LINKAGE PLATEChrome plated. Includes gaskets and a standardcable bracket for GM throttles.Holley & AFB.
PART NO.6035
FORD THROTTLE LEVER ADAPTERAdapts Edelbrock Performer Series carbs to Ford vehi-cles equipped with automatic transmissions (exceptAOD). 1968 and later.
CHRYSLER THROTTLE LEVER ADAPTERAdapts Edelbrock Performer Series carbs to Chrysler’sand accepts cruise control. 1966 and later.
PROGRESSIVE THROTTLE LINKAGE KITSDesigned for use with Edelbrock Dual-Quadmanifolds #5420, #5421, #5425, #5435 and#5440. High quality aluminum, stainlesssteel, brass parts and spherical rod ends forgreat performance and show quality.
DESCRIPTION PART NO.Progressive Dual Quad, Inline mount Edelbrock carbs 7094
Dual-Quad Fuel Line Kit, King Demon 8088
CARBURETOR LINKAGE BUSHING SET
Allows the fitting of a 1/4" fastener to the 1/2" dia. hole found inthe throttle linkage plate of Holley four barrel carbs. Split bushingdesign permits simple installation and eliminates the sloppinesspresent when rubber bushings are used. Gold iridite steel finish.
PART NO.64920
PART NO.1483
PART NO.1481
CARBURETOR LINKAGE BUSHING KITAllows the fitting of 1/4” fastener to the 1/2” diameterhole found in all GM and most Holley 4 bbl. throttlelinkage plates. Made of bright zinc plated cold rollsteel.
CARBURETOR BUSHING/PIVOT Carburetor bushing replaces a worn out sloppy factorybushing and gives smooth, trouble free throttle operation.Accommodates 1/4” diameter throttle rod.
DESCRIPTION PART NO.GM and most Holley carbs with 1/2” dia. throttle hole 1512
THROTTLE CABLE BRACKETS
DESCRIPTION PART NO.SBC & BBC w/ Edelbrock carb, black steel 8031Chevy SB (78 & earlier) w/ Edelbrock carb,
Cadmium plated8036
Ford 289-302, Throttle Cable Plate Kit 1490
CARBURETOR LINKAGE Ideal for any in-line application. Kit includescadmium-plated steel linkage rods andswivel ended hardware.
PART NO. DESCRIPTION3815 11” Linkage Rod Y4-28 threads
3830G Dual Quad Carb Linkage Kit - Universal Application
CARBURETOR LINKAGE COMPONENTSAllows you to assemble your own customcarb linkage system.
Provides stability and prevents any linkage piecesfrom falling down into the engine in the event ofvibration.
PART NO. DESCRIPTION3810G Ball Joint, Standard, 2/set3811G Ball Joint, Quick Disconnect, 2/set3812G 1/4” Rod Ends, 2/set
PART NO.6004
PART NO.6026
3815
8031
SAFETY PLATE DOMINATOR LINKAGE
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 99
100FU
EL D
ELIV
ERY
THROTTLE MICROSWITCH
PART NO.41678
BRAIDED STAINLESS UNIVERSAL THROTTLE ASSEMBLY
Housing with Cable
PART NO.20-88
Includes dual stainless steel throttle returnsprings (P/N 20-89). Works on Holleymodels 4150 and 4160 carburetors
DESCRIPTION PART NO.24-inch Housing with Cable R605436-inch Housing with Cable 8088
CARBURETOR THROTTLE CABLE BRACKET
Does not include bracket, Fits Dominator
LINKAGE PLATEChrome
DESCRIPTION PART NO.Holley & AFB Carburetor R2333
THROTTLE CABLE
DESCRIPTION PART NO.24” SS Hi-Tech, Blower Drive TC-1000BLD
24” SS Hi-Tech TC-1000HT36” SS Hi-Tech TC-1000HT36
36” SS Hi-Tech LSI TC-1000LS124” SS Hi-Tech Tuned-Port TC-1000TP
24” Universal Black TC-1000U36” Universal Black TC-1000U36
KICKDOWN CABLE BRACKETBolt to SB Chevy intake manifold as a convenientmounting point for the kickdown cable.
THROTTLE CABLE BRACKETDesigned to be used only on Holley model 4150 or 4160carburetors. Bolts on the carburetor flange ear.
THROTTLE CABLE BRACKETMount to the rear of Holley, Edelbrock, AIB,Quadrajet or inline dual carburetors. Thesebrackets are used to mount Lokar’s throttlecable and kick down assemblies. StainlessSteel and Polished, sold individually.
DESCRIPTION PART NO.Includes Springs SRK-4000
Bracket Only SRK-4001
THROTTLE BALL ASSORTMENTKit of one each, 1/4”, 5/16”, 7/32” & 3/8”.
PART NO.20-2
PART NO.20-45
PART NO.20-95
THROTTLE BRACKETS
DESCRIPTION PART NO.Chrome Universal Throttle Return Spring Bracket R2291
Chrome 2bbl/4bbl Adjustable Throttle Cable Bracketwith Automatic Transmission Kickdown
R9620
Chrome 2bbl/4bbl Adjustable Throttle Cable Bracket R9619
Chrome SB Chevy Throttle Cable Bracket Kit R9756
R9620
CHROME TRANSMISSION KICKDOWN BRACKET
DESCRIPTION PART NO.Chrome GM Turbo 350 Transmission
Kickdown BracketR9757
WIDE OPEN THROTTLE MICRO SWITCH BRACKET
DESCRIPTION PART NO.Black Wide Open Throtle Nitrous Switch Mount
Kit For 4150 Carb, Includes Micro Switch550165
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 100
101FU
EL DELIV
ERY
CHROME THROTTLE CABLE BRACKETSOne bracket is made for throttle cable only, theother has a secondary attachment for vehicleswith automatic transmission kickdown cables.
DESCRIPTION PART NO.Bracket for Moroso cable 6037
Throttle bracket only 6038Throttle bracket w/kickdown 6039
DESCRIPTION PART NO.Transmission kickdown stud, 5/16”, TH350/700R4 8018
CHROME THROTTLE SPRING BRACKETBrackets mount to carb stud or intake manifold.Slotted design fits most vehicles.
CARB LINKAGE BRACKETChrome Plated. Includes transmission kickdown cable bracket.
DESCRIPTION PART NO.Automatic Transmission 9620
SLIP LINKReplaces the “progressive” stock linkto provide simultaneous 1:1 primary and secondary opening rates.Requires drilling of existing primary throttle hole. One per package.
DESCRIPTION PART NO.Holley 4500 series, Carb Mount, dual springs 64923
2300/4150/4160 Series Holley Carb Mount, dual 64927Throttle Return Springs only, pair 64929
The answer to your throttle return springlinkage problems if you’re running a2300/2305 series two-barrel or 4150/4160series four-barrel Holley carburetor.Polished chrome finish. Includes one setof heavy and one set of light springs.
THROTTLE RETURN SPRING KIT
TRANSMISSION KICKDOWN STUD
PART NO.65444
PART NO.9885
PART NO.3683
DESCRIPTION PART NO.Holley Carburetor 4150-4160, 4 bbl., chrome R2083
Chrome Universal Throttle Return Spring Bracket R2291Chrome Universal Dual Throttle Return Spring Kit R6052
Stainless Throttle Cable Bracket & Spring Set R6055
THROTTLE RETURN KIT
PART NO.20-121
700R-4 KICKDOWN THROTTLE BRACKET
DESCRIPTION PART NO.Holley, 4010/4150/4160 45-456
CHOKE CONTROL CABLEMOUNTING BRACKETS
Attaches to throttle lever of Holley model4150/4160 carburetors. Designed For vehicleswith GM 700R4/200-4R transmissions.Includes bolts and instructions.
THROTTLE STOPManual Turn Knob. Baseplate style.
PART NO.65042
THROTTLE & SPRING BRACKETS
DESCRIPTION PART NO.4150 Chevy Throttle & Spring Bracket, PURPLE 6600
4150 Chevy Throttle & Spring Bracket, RED 6600R4150 Ford Cable Throttle & Spring Bracket, RED 6601RDominator Chevy Throttle & Spring Bracket, RED 6605R
A must for any cable type throttle linkage using regular Holley orDominator carburetors. Hardware is included for easy installation.
PART NO.5425
UNIVERSAL THROTTLE BALL ASSORTMENT KIT
THROTTLE CABLE BRACKETFor SBC engines through 1979. 2” adjustable range.
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 101
102FU
EL D
ELIV
ERY
Allows the easy addition of dualreturn springs to Holley 2300 and4150/4160 series carbs. Includesone set each of soft and firmsprings. Chrome.
41699
41689
PART NO. APPLICATION41699 Dual Return Spring Kit41689 Bracket and Springs
THROTTLE RETURN SPRING KIT
THROTTLE SOLENOIDReplacement for GM P/N 2060106. Requireslocknut.
THROTTLE LINKAGE BRACKETRYHardware kit needed when installing a Holleyuniversal carburetor with two mounting holesto a Ford with Automatic Transmission.
CHRYSLER THROTTLE LEVER EXTENSIONInstalls on any Holley square flange carburetorwith the universal throttle linkage.
ELECTRIC CHOKE CAPReplacement electric choke cap for carbModels 2300/4150/4160/4010/4011.
Fits carburetors designed with an “external” vacuum source such as 0-4412, 0-4776, 0-4777, 0-4778, 0-4779, 0-4780, 0-4781, 0-6299, 0-6708, 0-6709.
ELECTRIC CHOKE CONVERSION KITSCarburetors designed with an “internal”vacuum source such as 0-1850, 0-3310, 0-6425, 0-7448.
THROTTLE CONTROL STUDS
DESCRIPTION PART NO.3/8” Dia. throttle lever stud 20-36
7/32" Dia. throttle lever stud 20-371/4” Dia. throttle lever stud, brass 20-38
Throttle lever stud bushing 26-1035/16” transmission kickdown stud 20-40
DESCRIPTION PART NO.Throttle Solenoid 46-74
Locknut 26-57
PART NO.20-7
PART NO.20-91
PART NO.45-258
PART NO.45-224
PART NO.45-223
CNC Machined from aircraft quality 6061-T6 billet aluminum. Furnished witha specialty designed adjustable carburetor throttle cable end that is specifi-cally machined to fit your throttle cable to fine tune the perfect cable tension.
ANODIZED THROTTLE BRACKET W/RETURN SPRINGS
CLEAR BLACK DESCRIPTION550000 560000 4500 Carb Accepts GM Cable550001 560001 4500 Carb Accepts Lokar Cable550002 560002 4500 Carb Accepts Morse Cable550003 560003 4500 Carb Accepts Ford Cable550004 560004 Edelbrock Carb Accepts GM Cable550005 560005 Edelbrock Carb Accepts Lokar Cable550006 560006 Edelbrock Carb Accepts Morse Cable550007 560007 Edelbrock Carb Accepts Ford Cable550008 560008 4500 Carb Accepts Mopar Cable550009 560009 Edelbrock Carb Accepts Mopar Cable550010 560010 Bracket Fits 4150 & Edelbrock Carb550011 560011 Bracket Fits 4500 Carb
ANODIZED KICKDOWN CABLE BRACKETS
CLEAR BLACK DESCRIPTION550160 560160 GM Style Kickdown Detent Cable Bracket550161 560161 Lokar Style Kickdown Detent Cable Bracket
560160 560161
550001
550000
IDLE COMPENSATOR KITMaintains correct idle speed when airconditioner is on. Includes 12-voltsolenoid and mounting bracket for allEdelbrock square-bore carburetors.
PART NO.8059
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 102
103FU
EL DELIV
ERY
ELECTRIC CHOKE KITIncludes all parts necessary to convert1404, 1405, 1407 and 1411 EdelbrockPerformer Series carbs to electric choke.
DESCRIPTION PART NO.Choke Cap Kit 1474
Electronic Choke Kit (shown above) 1478Choke block off plate 8901
REPLACEMENT FUEL BOWL KITSAll listed below are standard finish with theexception of #34-502. Check carb model.
DESCRIPTION PART NO.Primary, Side hung, 4160 134-101
Secondary, Center hung, 4150/4160 134-102Primary, Center hung, 2300/4150/4160 134-103
Secondary, Center hung, 4150/4160 134-104Primary, Center hung, 4150/4500 134-108
Secondary, Center hung, 4150/4500 134-112
FUEL BOWL FITTINGInverted Flare or Standard.
DESCRIPTION PART NO.Inverted Flare Tube, 3/8”,
thread 7/8-20(A) x 5/8-18(B)26-26
Inverted Flare Tube, 5/16”, thread 7/8-20(A) x 1/2-20(B)
26-27
Carb inlet, 3/8”, thread 9/16-24(A) 26-29Carb inlet, 3/8”,
thread 9/16-24 (A) x 5/8-18 (B)26-43
HEX HEAD FUEL BOWL SCREWSDesigned for Holley 4150-4165 and 4500 model carburetors.Hex head screws are 2-1/2" long. Four per package.
NYLON FLOAT BOWL WASHER KIT10 per package.
CHOKE CONTROL CABLE KIT72” long and may be shortened with hand tools.Easy installation. Requires a 3/8" mounting hole.
FUEL BOWL PLUG KITService parts for quick change jet kits. 2 each.
DESCRIPTION PART NO.Fuel bowl plug kit 26-85
FUEL TRANSFER TUBEEach
DESCRIPTION PART NO.4160 model 26-115
PART NO.65414
PART NO.65225
PART NO.2078
DESCRIPTION PART NO.4150 style-8 pk. 5200
BOWL SCREW SET
DESCRIPTION PART NO.Chrome 6' Long R2332
CHOKE CABLE ASSEMBLY
DUAL THROTTLE RETURN SPRING KITUniversal in design and engineered for positivethrottle return to assure added safety. Springs areElectro-Nickel plated with chrome plated bracket.
THROTTLE RETURN SPRING KITFits Holley 2300/2305 series 2-bbl. and4150/4160 series 4 bbl. Includes heavy and lightsprings. Bracket is chrome plated steel. Also has many universal applications.
THROTTLE RETURN SPRINGSUniversal throttle return springs are ideal for OEM replace-ment or for custom applications. Each spring includes a1-1/2” angle bracket for easy mounting.
DESCRIPTION PART NO.2-3/4" Throttle return spring w/bracket 14
12" Throttle return spring w/bracket 13
PART NO.9678
PART NO.19
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 103
104FU
EL D
ELIV
ERY
BOWL SCREW GASKETS
DESCRIPTION PART NO.10 pack 11108
FUEL TRANSFER TUBE O-RING Package of two.
FUEL BOWL SIGHT PLUG & GASKET
DESCRIPTION PART NO.Replacement 2-pack 26-13
Replacement See-Thru SightPlug w/O-Ring Seal
26-113
CLEAR-VIEW SIGHT PLUGS FOR HOLLEY CARBSAllows you to check float bowl level without removing the plug and spilling fuel.
CLEAR-VIEW SIGHT PLUGS FOR HOLLEY CARBS
FUEL BOWL VENT BAFFLE/WHISTLEPrevents fuel from splashing out of the tube.
DESCRIPTION PART NO.1-7/16” length 26-89
The Engine Works billet machined float bowl extension increases fuel bowlcapacity and is custom machined to clear jet extensions. Kit includes gas-kets, extra length screws, accelerator pump lever and billet extension.
PART NO. APPLICATION41670 Billet float bowl spacer kit
CLEAR SIGHT PLUG KIT
PART NO. DESCRIPTION11113 Clear sight plug kit
BANJO FITTINGS
PART NO. APPLICATION11624 Banjo Swivel Fitting, 3/8” Hose
Engine Works racing fuel pump and regulators are designed to utilize theseO-ring style AN fittings. The O-ring design provides extra insurance againstthe possible leak of racing fuel.
O-RING FITTINGS
PART NO. APPLICATION41846 -6AN O-ring fitting41848 -8AN O-ring fitting41840 -10AN O-ring fitting
BILLET FLOAT BOWL SPACER KIT
FUEL FITTINGSDESCRIPTION PART NO.
7/8”-20 1543Straight 3/8” to 3/8” 2965
90˚, 3/8” to 3/8” 2966Straight 1/2” to 3/8” 2967
90˚, 1/2” to 3/8” 2968Chrome 90˚, 3/8” NPT to 3/8” 2970G
FUEL PRESSURE FITTINGSSaves wear and tear on carb inlet fittings by allowing quickand easy disconnection of fuel line. Blue anodized aluminum.
DESCRIPTION PART NO.Streamline, 90˚, 3/8” NPT to 3/8” hose, each 65140
3/8" Line w/Hose Fitting, each 653603/8”, NPT female to 3/8” NPT male, each 65310
3/8” NPT male to -6 AN male, each 65315Brass, 1/4” NPT to 3/8” hose, each 65375
Brass, 3/8” NPT to 3/8” hose, qty (2) 65380Brass, 3/8” NPT to 1/2” hose, qty (2) 65390
PART NO.26-37
PART NO.6057
PART NO.65226
BANJO FITTINGEdelbrock square-bore and Carter AFB carbs (5/8”-20).
INVERTED FLARE FUEL LINE FITTINGEdelbrock square-bore and AFB carbs, 3/8”.
BRASS FUEL LINE FITTINGEasily adapts rubber hose to NPT connections. NPTthreads on one side with a barbed end on the other.
DESCRIPTION PART NO.Straight 3/8” NPT to 3/8” ID hose (pair) 2270
90˚ 3/8” NPT to 3/8” ID hose (each) 2271
PART NO.8089
PART NO.8090
Fuel13v4o_Layout 1 10/31/13 2:19 PM Page 104
105FU
EL DELIV
ERY
FUEL REGULATORAdjusts from 1 to 6 lbs. Fits 5/16" and3/8" I.D. fuel line. Includes fittings, hoseand clamps. NOT FOR FUEL INJECTEDSYSTEMS.
LOW-PRESSURE FUEL REGULATORExcellent option for use with 12-801-1 “Red” pump.Regulates pressure from 1 to 4 PSI. 3/8” NPT ports.Includes mounting bracket.
FUEL INJECTION REGULATORDesigned to provide the correct fuel pressure for any highperformance fuel injected vehicle, 35 - 65 PSI.
DESCRIPTION PART NO.Clear coat, 85-92 Pontiac Firebird,
85-92 Chevy Camaro512-501
ADJUSTABLE FUEL PRESSURE REGULATORS• CNC Machined • Billet Aluminum Construction• Blue Anodized Finish• Allows Simple Full-Range Pressure Adjustment• Great for Normally Aspirated Supercharged Models
APPLICATION PART NO.Ford 5.0L 86-93 1706
Ford 4.6 & 5.0L V-8 90-97 1707
GM 305/350 TPI 85-92 (Includes TPI Runner Gaskets)
1714
FUEL PRESSURE REGULATORS
• Regulates from 4-1/2 to 9 PSI • One 1/2" NPT inlet and two 1/2" NPT outlet ports • 437" (7/16") restriction • Includes mounting hardware and AN style fittings • Polished Aluminum
• Regulates from 4-1/2 to 9 PSI • One -8 inlet port and four -6 outlet ports • .437" (7/16") restriction • Billet body & top casting cover are hard coat
black anodized • Three fuel pressure gauge mounting options
(fuel pressure gauge not included)
FUEL PRESSURE REGULATOR
FUEL PRESSURE REGULATORCOMPATIBLE FOR USE WITH METHANOL/ALCOHOL
DESCRIPTION PART NO.4-1/2 to 9 psi 12-704
DESCRIPTION PART NO.4-1/2 to 9 psi, black anodized 12-707
DESCRIPTION PART NO.4-1/2 to 9 psi, satin 12-803
Bypass style 12-803BP
SAFETY PRESSURE SWITCH Fits all electric pumps.
PART NO.9710
PART NO.12-810
PART NO.12-804
12-803
12-804
CLEAR ANODIZED REGULATOR BRACKETS
APPLICATION PART NO.4150 Carb & Aeromotive Regulator 550100
4150 Carb & Holley Regulator 550101
4150 Carb & Magnafuel Regulator 550102
4150 Carb & Mallory Regulator 550103
4500 Carb & Aeromotive Regulator 550105
4500 Carb & Holley Regulator 550106
4500 Carb & Magnafuel Regulator 5501074500 Carb & Mallory Regulator 550108
IN-LINE REGULATOR
DESCRIPTION APP. PSI PART NO.1/8"NPT female threaded port, dead head Carb 4.5 - 14 22205
22205
FUEL PRESSURE REGULATOR
PART NO. DESCRIPTION41803 Universal, 4.5 - 9 PSI
• Outlaw Black Anodized Billet Aluminum Body • Return Line Back to Tank NOT Required• Top Mount Adjuster Screw and Lock Nut for Fuel Pressure• 3/8" NPT Inlet and Outlet Ports• 1/8" NPT Female Port for Fuel Pressure Gauge• Mounting Bracket Included
DESCRIPTION APP. PSI PART NO.Regulator Carb 1 - 25 22206
Regulator EFI 30 - 100 22207
BYPASS REGULATOR ADJUSTABLE 4PTCarb, 1-25 PSI. eliminates pressure creep andvapor lock, Features extra large 3/4”-16 SAEthreads (-8 AN O-ring port fittings) side inlet andbottom return ports, with dual 3/8” NPT side out-let ports and one 1/8” NPT gauge port. Boost/vacuum reference port.
Use with Engine Works Throttle Brackets
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 105
106FU
EL D
ELIV
ERY
DESCRIPTION PART NO.Aluminum, 4-12 psi, 3/8” NPT, 2 port 4207
Black anodized, EFI 30-100 psi 4305M
2-PORT FUEL PRESSURE REGULATORFeatures a 1/2” NPT inlet port and two 3/8” NPT outletports. Flows 150 GPH and is adjustable from 4.5-10psi. Stainless steel bracket and hardware included.
DESCRIPTION PART NO.Aluminum Finish, 4.5 - 9 psi 10651
STREET & COMPETITION FUEL PRESSURE REGULATORS RETURN STYLEPort Return Style Fuel Pressure Regulators are designed toregulate fuel pressure between high pressure fuel pumps andcarburetors or fuel injection systems. This style of regulatorfeatures a fully machined housing form 6061-T6 aluminum billet withthree outlet ports and specially designed high flow fuel passages.
UNIVERSAL HIGH IMPEDANCE FUEL INJECTORS
PART NO. DESCRIPTION CT. PKG.150115 15.4lbs/hr @ 43.5psi each150117 17.3lbs/hr @ 43.5psi each150124 24.3lbs/hr @ 43.5psi each150140 39.7lbs/hr @ 43.5psi each150821 21lbs/hr 8/pkg150824 24lbs/hr 8/pkg150826 26lbs/hr 8/pkg150830 30lbs/hr 8/pkg150836 36lbs/hr 8/pkg
FUEL INJECTED PRESSURE REGULATORS
A1000-6 INJECTED BYPASS REGULATORImport-style EFI applications with –6AN fittings. Basepressure regulator is adjustable from 30 to 70 PSI.Alcohol compatible. 1/8” NPT gauge port.
CARBERATED FUEL PRESSURE REGULATORS
DESCRIPTION PART NO.Carbureted Adj., -6 AN female inlet & outlet ports 13201
A1000 Carbureted Bypass Regulator 13204Carbureted Adj. 3/8” NPT inlet & outlet ports 13205
Universal Bypass Regulator 13301
DESCRIPTION PART NO.Fuel Injected Adj. –10 AN inletports & one –6 AN return port
13101
EFI Rail Mount, Adj. Ford 94-97 5.0 & 96-98 4.6 liter
13102
EFI Rail Mount, Adj. Ford 86-93 5.0
13103
PART NO.13109
22801
OUTLAW SERIES ELECTRIC FUEL PUMPS
PART NO. APPL. TYPE GPH HP41106 Carb & EFI In-Line 110GPH @ Free Flow @ 13.5V up to 700hp norm asp
41825 EFI In-Line 43GPH @ 40PSI @ 13.5V up to 500hp norm asp
22801 Carb External 105GPH @ Free Flow @13.5V up to 250hp norm asp
22802 Carb External 120GPH @ Free Flow @ 13.5V up to 400hp norm asp
22815 Carb External 135GPH @ Free Flow @ 13.5V up to 700hp norm asp
• Race-Proven Outlaw Series • Re-engineered Rotary Vein Housing • Improved Fuel Flow, Long-Term Durability • LowAmperage Draw, Ultra Quiet Operation, Rebuildable • External PressureRelief Valve • 3/8" NPT Female Inlet and Outlet • Mounting Brackets andHardware Included • 22815 is Alcohol Compatible
PART NO. DESC. HORSEPOWER PRESSURE
MP-9433 4-port 1,600+ 4–12psi1 x #10 in, 4 x #6 out
MP-9833 Large 2-port 1,600+ 4–12psi1 x #10 in, 2x #8 out
MP-9633 2-port 750+ 4–12psi1 x #10 in, 2x #6 out
PART NO. DESC. HP PRESSUREMP-9925-B Two-port EFI w/ 1:1 Boost
Reference700 35-85 psi
2 X #8 AN, 1 X #6 AN return
CARBURETED REGULATORSSuitable for drag racing, circle track, road racing, mud bog,power boat, tractor pulling. Adjustable base pressure.Machined from billet aircraft aluminum and anodized forlong lasting finish. Precise pressure control.
QUICKSTAR SERIES EFI REGULATORS
Guided-metering valve provides precise control, requiresless maintenance. MagnaFuel Regulators are compatiblewith racing gasoline and alcohol fuels. Billet body precisionCNC-machined from aircraft-quality aliminum and hardanodized for extra long service life. Completely user-serviceable, with ready to order replacements parts.
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 106
107FU
EL DELIV
ERY
QUIET FLOW™ ELECTRIC FUEL PUMPManufactured by Essex Industries. Factorytested, includes mounting brackets. #1791is factory preset to 6.5 PSI and no regulatoris required.
DESCRIPTION PART NO.120 GPH (free flow), 3/8” NPT inlet/outlet 1791
COMPETITIONELECTRIC FUEL PUMPThe First Choice for Competition provides constant fuelflow with no pulsation. Pressure pre-set at 14 PSI. Flows70 GPH at 9 PSI. Free flow capacity is 110 GPH.Includes mounting bracket and 12-803 high pressureregulator.
STREET PERFORMANCEELECTRIC FUEL PUMPThe #1 Choice for Street Performance provides constantfuel flow with no pulsation. Pressure pre-set at 7 PSI.Flows 67 GPH at 5 PSI. Free flow capacity is 97 GPH.Does not require a regulator for most applications.Includes mounting bracket.
IN-LINE EFI & TBI FUEL PUMPS• OE-proven, lightweight, compact design• Rubber isolator, mounting clamps, and electrical
hardware is included for quiet operation andsimplified installation
PRO-SERIES ELECTRIC FUEL PUMPHigh output fuel pump in a distinctive black color, provides constant fuel flow with no pulsation. Flows 140GPH (free flow) & 120 GPH at 9 PSI with a pre-set pres-sure of 14 PSI. Includes 3/8” NPT inlet & outlet ports.Rugged pump is highly tolerant of contaminated fuels &weighs less than 3 lbs.
DESCRIPTION PART NO.“Blue” Race Pump 12-802-1
DESCRIPTION PART NO.“Red” Street Pump 12-801-1
APPLICATION PART NO.Multi-Point EFI Systems 12-920
-8 Fitting Kit 26-180
VICTOR SERIES 130 GPH RACING FUEL PUMPS FOR GASOLINEEdelbrock’s 6-valve racing fuel pumps flow130 GPH. A must for drag racing, circletrack racing, street machines or any applica-tion that demands a high volume fuel deliv-ery. 1/2” NPT inlet and outlet orifices sur-pass the capacity of conventional models.13 to 14 PSI.
PERFORMER SERIES STREET 110 GPH FUEL PUMPSDesigned to match Performer Seriescarburetors, Edelbrock’s High-PerformanceStreet Fuel Pumps have six valves and a flowcapacity of 110 gallons per hour. High-volume, 3/8"NPT inlet and outlet surpasses the capacity ofconventional models. Produces 6 psi which is correctfuel pressure for street use. For gasoline or mixed fuels only.
DESCRIPTION PART NO.Small Block Chevrolet 1721Big Block Chevrolet 1722
DESCRIPTION PART NO.Small Block Chevrolet 1711
PART NO.12-815-1
MARINE 67 GPH “RED” ELECTRIC FUEL PUMPMeets U.S. Coast Guard regulations,Compatible with Gasoline or Alcohol.
DESCRIPTION PART NO.67 GPH at 5 PSI 712-801-1
BILLET BASE HP ELECTRIC FUEL PUMPSGeroter Design. Street/Strip Application. Compatible withGasoline or Alcohol.
DESCRIPTION PART NO.125 GPH, 110 GPH at 7 PSI 12-125150 GPH, 140 GPH at 7 PSI 12-150
MECHANICAL STREET/STRIP FUEL PUMPS.90GPH @ 6PSI2 Valve High Performance Fuel Pumps• For Stock and Medium Performance
Applications• High Volume 70 gallons per hour (free flow)• 8 PSI shutoff pressure• Chrome Plated Castings to prevent corrosion
and give the performance look
PART NO. DESCRIPTION
PC2703 SB Ford 289-351W
PC2704 SB Ford 351C/M 400M
PC2751 SB Chevy
PC2702 BB Chevy 396-454
PC-2703
PC-2702
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 107
109FU
EL DELIV
ERY
ELECTRIC FUEL PUMP KITFord 86-98, 4.6/5.0 GT 255 LPH
DESCRIPTION PART NO.Ford Mustang, In-tank, 255 LPH, 90 PSI 1607
A1000 FUEL PUMPCarbureted powerplants making up to 1200 HP and fuelinjected engines:• up to 700 HP - forced air induction• up to 1000 HP - naturally aspirated• up to 1200 HP - carbureted systemsFlows at 500 lbs. per hour @ 12 volts and 45 psi.Features -10AN inlet and outlet ports
A2000 DRAG RACING FUEL PUMPApplications producing 500-2000 HP.• Delivers free flow rates of more than 350
gallons per hour.• Flows enough fuel @20 PSI to support
engines that surpass 2,000 HP.• Features –10AN inlet and outlet ports
with a –8AN return port• 1/8” NPT gauge port and mounting bracket
STREET ROD FUEL PUMPCarbureted powerplants making 200-750 HP• Fuel flow exceeds 900 lbs. per hour @
13.5 volts - more than 150 gallons per hour• Pump provides 18-20 PSI fuel pressure -
perfect for high-G cars• 3/8” NPT ports facilitate easy installation• Alcohol compatible
ELECTRIC FUEL PUMP
DESCRIPTION PART NO.140+ GPH & Regulator non-return 4140
140+ GPH, Free flow 4150
PART NO.11101
PART NO.11202
PART NO.11203
ELIMINATOR FUEL PUMP• ORB-12 inlet port• ORB-10 outlet port• Fully-submersible for custom in-tank placement• Flow exceeds 800 lbs/hour @ 13.5 volts/45 psi• Flow exceeds 1000 lbs/hour @ 13.5 volts/8 psi• Black anodized• External
PART NO.11104
DESCRIPTION PART NO.
Seals for Fuel Pump #MP-4401 MP-4401-SK
Seals for Fuel Pump #MP-4450 MP-4450-SK
Seals for Fuel Pump #MP-4550 MP-4550-SK
DESCRIPTION PART NO.
ProStar 500 Pump with Filter, 8.25" x 3" x 7",8 lbs, 2000 HP, 25 to 36 psi
(13 amps @ 28 psi), 12 In/Out, #8 Bypass
MP-4450
ProStar 500 Fuel Pump, 5.75" x 3" x 7", 7 lbs,2000 HP, 25 to 36 psi
(13 amps @ 28 psi), 12 In/Out, #8 Bypass
MP-4401
QuickStar 275 Fuel Pump, 5" x 3.5" x 6.5", 5.5 lbs., 750 HP, 18 psi (8 amps @ 18 psi),
#10 In/Out, #8 Bypass
MP-4501
QuickStar 300 Fuel Pump, 5" x 3" x 6.75", 7 lbs, 950 HP, 5 to 36 psi (10 amps @ 25 psi), #10
In/Out, #8 Bypass
MP-4601
QuickStar 300 Pump with Filter, 8" x 3" x 6.75"8 lbs, 950 HP, 25 to 36 psi (10 amps @ 25 psi)
#10 In/Out, #8 Bypass
MP-4650
FUEL PUMPS
ELECTRIC FUEL PUMP REBUILD KITS
• Race-proven low amperage motor• Reliable, consistent fuel supply with superior flow• Instantaneous compensation for sudden changes in fuel demand• External bypass eliminates cavitation and fuel starvation• Resin-impregnated stainless steel rotor in a polymer wear ring• Compatible with alcohol and gasoline racing fuel• Designed for 12V or 16V applications• CNC'd 6061 aluminum pump body• No metal-to-metal contact within pump itself• Horsepower ratings (below) are for naturally aspirated engines
running gasoline• Rebuildable to as-new condition• Fittings not included
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 109
110FU
EL D
ELIV
ERY
STREET PERFORMANCE 80 GPH FUEL PUMPS Up to 80 GPH (free flow), 7-1/2 PSI shutoffpressure. Adjustable lower housing allows 360°rotation of fuel inlet/outlet fittings for custominstallation. Triple chrome plated.
COMPETITION 110 GPH FUEL PUMPSHigh output fuel flow. 3/8” NPT inlet/outlet portsflow 110 GPH (free flow). Shut off pressure pre-setfrom 6-1/2 to 8 PSI. Fuel body can be rotated.
PRO-SERIES 130 GPH RACING FUEL PUMPSMaximum fuel flow. 130+ GPH (free flow). Shut offpressure pre-set 7-1/2 to 9 PSI. Inlet and outletports are 1/2” NPT. Fuel body may be rotated. Fuelpressure regulator 12-803 is required.
DESCRIPTION PART NO.Chevy SB 12-834Chevy BB 12-835
Ford 289/302/351W 12-833Ford 351C/351M 12-854
Ford 429/460 12-860Pontiac 12-837
KEITH DORTON 170+ GPH RACING FUEL PUMPSHigh Output Fuel Flows at 170+ GPH.
DESCRIPTION PART NO.Chevy SB 12-327-13Chevy BB 12-454-13
Ford 289/302/351W 12-289-13
DESCRIPTION PART NO.Chevy SB 12-327-20Chevy BB 12-454-20
Engine Works In-Tank Electric FuelPumps offer the fuel flow needed for today’s hot street performance machines. Choose from three performance options;• 190 lph (liters per hour) - Free flows up to 50 gallons of fuel per hour.
Capable of flowing enough fuel for 600 horsepower applications.• 255 lph - Capable of free flowing 65 gallons an hour. Recommended for
engines up to 750 horsepower.• 255 HO - High pressure output. Flows 65 gallons an hour but at pressures
of up to 80 psi. Flows more fuel in “real life” applications. Recommended for larger cubic inch race setups. Each kit is complete andincludes all installation parts, accessories and instructions.
IN-TANK ELECTRIC FUEL PUMP
• For 2000+ HP based on naturally aspirated engines running gas• Ideal for street muscle cars• Compact and lightweight, great for tight fits (7" L x 3" dia, 4.5 lbs)• -8AN inlet/outlet ports• 20 to 120 psi• Self-priming, continuous duty.
Inlet/Outlet fittings not included.
PROTUNER IN-LINE ELECTRIC FUEL PUMPS
DESCRIPTION PART NO.2000+ HP, 14 amps at 45 psi MP-43031500+ HP, 12 amps at 45 psi MP-4301
First electric gear pump on the market. Swivel adapterallows more mounting options. Swivel flange allows you to loosenpinch bolt and swivel the head 360° after the pump is mounted tooptimize the fuel line routing. Provides highest volume at highest pressure...Period. Never requires voltage reduction devices due to high quality motorconstruction. Compatible with alcohol and gasoline racing fuels
Belt drive with industry standard coupling forinstant swap to high performance. CNC machinedbody, with hard-anodized finish is compatible withgas, methanol and ethanol
SWIVELING ELECTRIC GEAR PUMP
OUTLAW SERIES BELT DRIVE PUMP
APPLICATIONS ENGINE 190LPH 255LPH 255HOAcura Integra 94-98 1.8L --- 41971 41972
Buick Regal/GN 3.8L turbo --- --- 41911Chevrolet Camaro 85-91 5.0L/5.7L --- --- 41911
Ford Mustang 85-97 4.6L/5.0L 41951 41952 41953Honda Civic 92-98 1.5L --- 41971 41972
Ford Lightning - 2 pump system 5.8L --- 41957 ---Universal Inline - 255 Iph --- --- 41900 ---
DESCRIPTION PART NO.Chevy SB 12-327-11Chevy BB 12-454-11
Chrysler SB 12-360-11Chrysler BB 12-440-11
Ford 289/302/351W 12-289-11Ford 390, 427, 428 FE 12-390-11
Ford 429/460 12-460-11Pontiac all 12-389-11
41971
DESCRIPTION PART NO.ProStar EFI Series, 2,500+HP,
17 amps at 45 psiMP-4703
DESCRIPTION PART NO.Up to 150 psi Rail Pressure,
10.5 gpm @ 4,000RPM, #10 AN in and out
MP-4205
MP-4301
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 110
111FU
EL DELIV
ERY
FUEL PUMP PUSH ROD KITSAPPLICATION PART NO.
SB Chevy 134-8701BB Chevy 135-8701
Lightweight tubular design with hardened ends. One tip is hardenedsteel, the other bronze for use on all aftermarket camshafts.
DESCRIPTION PART NO.SB & BB Chevy - Standard Length 41877
0.200” longer pushrod, Merlin & Rocket Blocks 41878
LIGHTWEIGHT FUEL PUMP PUSHROD
FUEL PUMP PUSHRODChromemoly, Bronze Tip, each.
DESCRIPTION PART NO.SB & BB Chevy Fuel Pump Pushrod 4607
FUEL PUMP PUSHRODLightweight, for use in Drag, Oval Trackand Street Performance applications.
DESCRIPTION PART NO.SB & BB Chevy 65750
FUEL PUMP PUSHRODLIghtweight, used with mechanical fuel pumps.
DESCRIPTION PART NO.SB & BB Chevy 6056
Dress up the fuel pump area on SB Chevy265-400. Ideal for mounting stock OEM typepump. Complete with gasket.
CHROME FUEL PUMP MOUNTING PLATE
FUEL PUMP SPRINGHeavy Duty. Boosts Holley electricfuel pump pressure from 12 to 19 PSIand increases fuel volume.
FUEL PUMP BLOCK-OFF PLATESDesigned to block off the fuel pump mount-ing boss when a mechanical fuel pump is notused. Available in two popular styles. Madeof gold anodized aluminum or high lustertriple chrome plated steel. BB Chevy, 273-440 Chrysler and All Fords except 351C,351M and 400.
DESCRIPTION PART NO.Gold Anodized Aluminum 65392
Chrome Plated Steel 65394
CHROME FUEL PUMP BLOCK-OFF PLATESChrome plated steel block-off plates cover stockfuel pump openings. Gasket included.
DESCRIPTION PART NO.SB Chevy 1515
BB Chevy & most V8 & V6 1516
DESCRIPTION PART NO.Fuel Pump Spring 65770
PART NO.1514
FUEL PUMP MOUNTING PLATEWITH GASKETChrome Steel, SB Chevy 283-400
PART NO.R2310
FUEL PUMP BLOCK-OFF PLATES
FUEL PUMP BLOCK-OFF PLATEWITH GASKETChrome Steel, BB Chevy.
PART NO.5422
DESCRIPTION PART NO.Polished Aluminum SB Chevy, No gasket R6257
Polished Aluminum BB Chevy, No gasket R6258
Clear, Red, Blue or Black Anodized BilletAluminum. Includes Gaskets and StainlessSteel Socket Head Screws.
DESCRIPTION PART NO.Clear Fuel Pump Block-Off Plate Kit, SB Chevy 550400Clear Fuel Pump Block-Off Plate Kit, BB Chevy 550401Red Fuel Pump Block-Off Plate Kit, SB Chevy 570400Red Fuel Pump Block-Off Plate Kit, BB Chevy 570401Blue Fuel Pump Block-Off Plate Kit, SB Chevy 580400Blue Fuel Pump Block-Off Plate Kit, BB Chevy 580401Black Fuel Pump Block-Off Plate Kit, SB Chevy 560400Black Fuel Pump Block-Off Plate Kit, BB Chevy 560401
BILLET FUEL PUMP BLOCK-OFF PLATES
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 111
112FU
EL D
ELIV
ERY
FUEL PUMP CHECK VALVE KITKit for Electric Pumps.
DESCRIPTION PART NO.Fits Holley 12-801, 1 Pump 12-806Fits Holley 12-802, 1 Pump 12-805
FUEL PUMP ROTOR & VANEKit for Electric Fuel Pumps.
DESCRIPTION PART NO.Fits Holley 12-801 & 12-802,
one pump12-811
FUEL PUMP BLOCK-OFF PLATESFor use on Chevrolet V8s. Stamped withthe handsome Chevrolet Bow Tie, theseplates are supplied with special non-asbestos gaskets.
DESCRIPTION PART NO.SB Chevy, Bowtie Emblem 141-210BB Chevy, Bowtie Emblem 141-211
BB Chevy & most V6, Ford 289-302 and Chrysler273-440, with Gasket
66107
For 200-1000 HP applications. CNC machinedfrom 6061-T651 aluminum alloyed.
FUEL FILTERS
PART NO. DESCRIPTION12301 10 Micron with Paper Element12601 Fabric Fuel Filter Element for 1230112303 40 Micron with Replaceable Element12304 Cleanable 100 Micron S/S Element12305 Billet Fuel Filter Mount
• Aircraft-quality aluminum for lightweight strength• End caps equipped with O-rings for leakproof operation• Cleanable, reusable, replaceable filter elements• Gas and methanol/ethanol compatible• Virtually no loss of flow volume or pressure• Female AN ports for a variety of fitting options• Durable anodized coating for corrosion resistance
IN-LINE PRE FILTERS
PART NO. DESCRIPTION
MP-7009 74-Micron, 4-3/4" x 2-1/8" diameter-10AN Inlet/Outlet ports
MP-7008 25-Micron, 4-3/4" x 2-1/8" diameter,-10AN Inlet/Outlet ports
MP-7006 150-Micron, 6-1/2" x 2-1/2" diameter -12ANInlet/Outlet ports
PERFORMANCE THROTTLE BODIES
THROTTLE BODIES V-6,4.6 & 5.0 MUSTANG
F-SERIES, EXPEDITION, RANGER & EXPLORER
APPLICATION PART NO.70mm (1986-93 5.0L Ford) 150175mm (1986-93 5.0L Ford) 1503
70mm EGR Spacer Plate (1986-93 5.0L Ford) 150275mm (1996-2004 4.6 2-V Ford) 1701
75mm (1997-2002 4.6/5.4 F-Series/Expedition) 1703Twin 56mm (1987-96 302/351 F-Series) 3501
THROTTLE BODY GASKETS
APPLICATION PART NO.Holley 2300 Carburetor 108-40
Holley 4150-4160 Carburetors 108-5
APPLICATION PART NO.Twin 52mm (1994-97 GM LT-1) 1543Twin 58mm (1994-97 GM LT-1) 1544
80mm (1998-2003 F-Body/04 GTO, 99-02 Full SizeTrucks), Includes adapter kit
1709
78mm, Ford, Modular V8, 4.6L 1780
85MM HIGH-FLOW LS1/VORTECTHROTTLE BODYDirect bolt-on for 98-03 Camaros and Firebirds,04 GTO's and 99-02 full-size GM trucks with4.8L, 5.3L & 6.0L engines and cable stylethrottles.
PART NO.17090
108-40
Power-Plus series throttle bodies have youcovered when it comes to increased airflowfor your late model vehicle. Cast from high-quality 356 aluminum alloy and aremachined on state-of-the-art CNC machin-ing centers to ensure a perfect fit on yourcar or truck. Their features include double-sealed bearings, O-ringed throttle shafts, and precision die-stamped linkages.
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 112
113FU
EL DELIV
ERY
POWER™ THROTTLE BODIES
PART NO. APPLICATION69201 70mm Throttle Body for 1986-93 Mustang 5.0L V8*69202 75mm Throttle Body for 1986-93 Mustang 5.0L V8*69211 70mm Throttle Body for 1994-95 Mustang 5.0L V8 69501 70mm EGR Plate for 1986-93 Mustang 5.0L V869502 75mm EGR Plate for 1986-93 Mustang 5.0L V8
69200
*Street Legal applications must also use #69500 Series EGR Plates.
• Better airflow than OEM or aftermarket90mm units due to enlarged throttle opening & modified internal design• Dual spring mechanism & beefed up link-age for total throttle control• Increased thickness of both the throttleblade & the shaft resists deflection, especially in boosted applications• Offset blade pivot allows for smoother operations & significantly
improves throttle response
DESCRIPTION PART NO.92mm, Fits LSX & LSXR Intake Manifolds 54092
BIG MOUTH THROTTLE BODY
DESCRIPTION PART NO.-8AN Fittings, 6-1/2” Length 65230
IN-LINE FUEL FILTERRemoves dirt and debris from fuel systems. Blue anodized aluminum. 40micron stainless steel filter element.
INLINE STREET FUEL FILTER
DESCRIPTION PART NO.160 GPH, 35 microns 10210
HIGH EFFICIENCY 140 SERIES FUEL FILTERPerfect for engines that require a maximum flow and aminimum restriction filter.
DESCRIPTION PART NO.Replacement Fuel Filter Element & O-Ring 3141
FUEL FILTEREach
DESCRIPTION PART NO.Chrome plated. 3/8” O.D. in/out 6153
COMPETITION FUEL FILTER
DESCRIPTION PART NO.90 GPH fuel flow filters to 10 microns
w/replaceable paper element10100
Replacement Element Kit for 10100 10120
CHROME PLATED CANISTER FUEL FILTERSMr. Gasket’s chrome plated fuel filter is a welcome addition to any cus-tom and performance engine. Polished and chrome plated to a highluster to complement other under hood chrome accessories. Inlet/out-let openings have a safety bead for positive fuel line retention. Filter isvisually packed complete with two chrome clamps.
DESCRIPTION PART NO.5/16” ID hose 97453/8" ID hose 9746
DESCRIPTION PART NO.Fits 3/8", 5/16" and 1/4" ID 9706
Fits 5/16" ID hose 9747Fits 3/8" ID hose 9748
DESCRIPTION PART NO.Chrome Fuel Filter - 3/8-inch Inlet & Outlet R9177Chrome/Clear Fuel Filter - 3/8-inch Inlet & Outlet R9245
Billet Aluminum Fuel Filter - 3/8-inch R9407
CLEARVIEW FUEL FILTERSFeatures chrome plated ends that are barbedfor positive fuel retention. Kit is complete withfour chrome plated fuel line clamps and twoshort lengths of fuel hose.
#9747
#9745
FUEL FILTERS
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 113
114FU
EL D
ELIV
ERY
For fuel needs of engines from 200 to 1000 HP.175 GPH with less than .15 psi pressure drop.Alcohol and gas filter elements are available,each providing 10 micron filtering protection.
PART NO. APPLICATION41710 Street/Strip Fuel Filter41720 Replacement Element
STREET FUEL FILTERSGlass and chrome construction
PART NO. APPLICATION41701 5/16” Filter41702 3/8” Filter41703 Replacement Element
41701
Allows the filter to be mounted in tighter quarters thanthe 41710. Unit has 3/8 NPT ports, flows at a high ratefor carbureted applications, and filters down to 35microns. 4.5" high by 2.5" diameter housing.
PART NO. APPLICATION41711 Street/Strip Fuel Filter41721 Replacement Element
CHROME STREET/STRIP FUEL FILTER
Flows up to 90 GPH and holds up to 200 psiof pressure. Features an easily replaceablefilter element and may be plumbed with ANtype fittings and hose or with hose barb typefittings.
COMPETITION FUEL FILTER
BILLET IN-LINE FUEL FILTERS
PART NO. COLOR LENGTH IN/OUT MICRON FILTER42740 Black 2-1/2" 4AN 40 Wire Screen
42740-BLUE Blue 2-1/2" 4AN 40 Wire Screen42750 Black 2-1/2" 6AN 40 Wire Screen
42750-BLUE Blue 2-1/2" 6AN 40 Wire Screen42760 Black 3-3/4" 6AN 40 Wire Screen
42760-BLUE Blue 3-3/4" 6AN 40 Wire Screen42770 Black 2-5/8" 8AN 40 Wire Screen
42770-BLUE Blue 2-5/8" 8AN 40 Wire Screen42780 Black 4" 8AN 40 Wire Screen
42780-BLUE Blue 4" 8AN 40 Wire Screen42800 Viton O-Ring Seal 42740, 42750, 42760, 42770, 4278042801 Filter Screen - 40 Micron
42880 Black 6-1/4" 8AN 10 Media42880-BLUE Blue 6-1/4" 8AN 10 Media
42881 Black 6-1/4" 8AN 100 Stainless42883 Black 6-1/2" 10AN 100 Stainless42885 Black 8-1/4" 12AN 100 Stainless42802 Viton O-Ring Seal 42880, 42881, 4288342803 Filter Media Cellulose - 10 Micron42804 Viton O-Ring Seal 4288542805 Filter Stainless Mesh - 100 Micron - 12AN
Filter Stainless Mesh - 100 Micron - 8/10AN42806
PART NO. COLOR LENGTH IN/OUT MICRON FILTER41750 Black 11-1/2" 10AN 100 stainless
41750-RED Red 11-1/2" 10AN 100 stainless41751 Black 11-1/2" 8AN 120 media
41751-RED Red 11-1/2" 8AN 120 media41752 Black 11-1/2" 6AN 120 media
41752-RED Red 11-1/2" 6AN 120 media41761 1-1/2" fuel filter roll bar bracket, 1-7/8" fuel filter diam.41780 Stainless filter - 100 Micron41781 Paper media filter - 120 Micron
41752-RED 41751
42760
• 6061 Billet Aluminum• Race and Street Applications• O-Ring allows easy access to clean/wash
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 114
115FU
EL DELIV
ERY
ALUMINUM FUEL CELLSTIG-Welded 5051 Strong Lightweight AircraftAluminum Alloy. Natural Aluminum Color. #8AN Male Fittings. 2 Pickups, 1 Return, and 1Rollover Vent. Available with 0 to 90 OhmSending Unit.
DESCRIPTION PART NO. 8" x 8" x 15" (3 Gallon) 2030A12" x 10" x 8" (4 Gallon) 2040A12" x 12" x 8" (5 Gallon) 2050A17" x 17" x 9" (10 Gallon) 2100A20" x 18" x 10" (15 Gallon) 2150A
20" x 18" x 10" (15 Gallon with sending unit), Sump
2150AS
20" x 18" x 10" (15 Gallon with sending unit) 2151AS24" x 20" x 10" (20 Gallon) 2200A
24" x 20" x 10" (20 Gallon with sending unit) 2200AS
DESCRIPTION STAGE 1 W/O FOAMPART NO.
STAGE 2 W/FOAMPART NO.
9" x 9" x 13" (4 Gallon) 1040D 2040D
13" x 13" x 8" (5 Gallon) 1050D 2050D
17" x 17" x 8" (8 Gallon) 1080D 2080D
17" x 17" x 11" (12 Gallon) 1120D 2120D
6" x 6" x 12" (1 Gallon) 1010D 2010D
23" x 17" x 11" (16 Gallon) ----- 2160D
23" x 17" x 11" (16 Gallon) 1160S (Pro Street) -----
DRAG RACE FUEL CELLSRCI Stage 1 Drag Race Fuel Cellscome with a flush mount aircraft typefill lid. All cells have a 2" sump to funnelfuel toward the two #8 AN outlet fittingsplus one #6 AN vent fitting. RCI Stage 2Drag Race Fuel Cells have all the features ofthe Stage 1 Fuel Cells with the addition ofanti-slosh safety foam. Note: Pro Street cells include built-in fuel
sending unit, no sump
PART NO. DESCRIPTION7030A Complete kit7031A Cap only
FUEL CELL MOUNTING CAPS12 bolt holes
CIRCLE TRACK CELLSRCI Circle Track Cells are molded withcross-linked maximum strength polyethyl-ene with an internal pickup hose in the rightrear corner. RCI Cells with steel cans comecompletely assembled with poly cell andsteel container as one unit.
DESCRIPTION W/STEEL CAN 17" x 17" x 11" (12 Gallon) 1122C23" x 17" x 11" (16 Gallon) 1162C33" x 17" x 10" (22 Gallon) 1212C25" x 17" x 14" (22 Gallon) 1222C
CELL MOUNT KIT
DESCRIPTION PART NO.4 Gallon 7404A5 Gallon 7405A8 Gallon 7408A12 Gallon 7412A16 Gallon 7416A
FUEL CELL SAFETY FOAMPer Stick.
PART NO.7050A
ROLLOVER VENT
DESCRIPTION PART NO.8AN male to male 7020A
PART NO.7021A
FUEL CELL ROLLOVER VALVE
Natural Aluminum. Female -8AN to Male -8 AN.
PART NO. DESCRIPTION12720 Fuel Tank Sump Kit
FUEL TANK SUMP KIT• Ensures positive fuel flow• Designed to fit stock fuel tanks• Manufactured from 18-gauge
cold rolled steel for easy welding• Fittings not included. Welding required.• Two 1/2" NPT weld bungs.
PART NO. DESCRIPTION550550 Clear Annodized w/Bung Assembly570500 Red Annodized w/Bung Assembly580500 Blue Annodized w/Bung Assembly560500 Black Annodized w/Bung Assembly
BILLET FUEL CELL CAPS
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 115
116FU
EL D
ELIV
ERY
FUEL FUNNEL
DESCRIPTION PART NO.Red plastic, 6 qt. capacity 3695Red plastic, 2 qt. capacity 3697
DESCRIPTION PART NO.White Square 42400Red Square 42401Blue Square 42402
5 GALLON FUEL JUGS
Square 5-Gallon Racing Jug is available in White, Red or Blue. Thejug and vent caps are designed with rubber gaskets to preventleaking. “Quick Pour”Design offers quick, clean and easy refuels.
LARGE FUEL FUNNEL WITH FILTERLarge opening catches fuel to reduce spillage.
DESCRIPTION PART NO.Hose 70056Cap 70057
CAP & HOSE
PART NO. APPLICATION
42301 Large funnel
42302 Filter
MANHATTAN OIL
ALCOHOL TOP LUBE POWER PLUSEliminate cylinder washdown and excessive wear withoutdealing with the nauseous exhaust fumes from your racevehicle with these Manhattan Oil Power Plus Top Lubefuel fragrances. They eliminate unpleasant exhaust fumes and the eye,nose, and throat irritation that come with them. Just mix with your regularfuel. One 16 oz. bottle treats up to 55 gallons of alcohol.
PART NO. DESCRIPTION19769-18 Cherry19769-31 Groovy Grape19769-35 Strawberry
Why deal with the nauseous exhaustfumes from your race vehicle when youcould be sniffing root beer, pina cola-da, or bubble gum instead? ManhattanOil fuel fragrances eliminate unpleasantexhaust fumes and the eye, nose, and throat irritation that come withthem. Just mix with your regular fuel - one 4 oz. bottle treats 30 gallonsof alcohol or 20 gallons of gas. Available in 19 different fragrances.
FUEL FRAGRANCE
Increases octane effect up to 10 points while improvingcombustion in all grades of gasoline
OCTANE BOOSTER
DESCRIPTION PART NO.Street Formula, 6 oz., Treats 30 Gallons 19769-63FUEL ADDITIVES
DESCRIPTION PART NO.Fast Forward (Increases HP) 1616
Drag Racing Treatment 6072
GASGACINCH GASKET SEALEREnsures proper sealing of all gaskets used in amanifold installation. It's also effective on water pump,oil pan, and valve cover gaskets. It allows easy gasketremoval during parts disassembly, is water and oil-resistant, and comes in resealable 4 oz. container.
DESCRIPTION PART NO.Gasgocinch - 4 oz. 9300
DESCRIPTION PART NO.Atomic Apple 19769-50Banana Blast 19769-42
Burn Out Blueberry 19769-52Full Blown Bubble Gum 19769-44
Cherry Bomb 19769-19Super Sonic Cinnamon 19769-39Rocket Cotton Candy 19769-49
Flyin' Hawaiian Fruit Punch 19769-46Groovy Grape 19769-32
Peel Out Pina Colada 19769-47Radical Racin' Raspberry 19769-41
Reefer Madness 19769-71Rippin' Root Beer 19769-45
Oils All Supercharged Strawberry 19769-36Turbo Tangerine 19769-53Victory Vanilla 19769-43
Wicked Watermelon 19769-48
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 116
117FU
EL DELIV
ERY117
FLASHPAQThe Flashpaq performance tuner is the bestselling handheld tuner in the world. The suc-cess of the tuner is due to its' quality, innova-tion and performance results. The Flashpaqhas set many standards for the industryincluding updating over the internet, firsthandheld in the industry, and first portablediesel tuning device. The Flashpaq continuesto deliver incredible results letting userschoose from multiple power levels and a vari-ety of user-tunable options for the almost1,000 vehicles Superchips tunes.
1840: 1999-2013 Ford Gas1999-12 Ford Diesel
2840: 1999-13 GM Gas2001-13 GM Diesel
3840: 1998-10 Dodge/Chrysler Gas1998.5-09 Dodge Diesel
CORTEXThe Cortex performance tuner is Superchipspremium handheld product. When Cortex wasintroduced it was a groundbreaking deviceoffering exclusive value-added features thecompetition still to this day can't match includ-ing a 2-year powertrain warranty and the abili-ty to tune a second vehicle from the sameOEM family on one tuner with our Multivinapplication. The second vehicle tuning is avail-able exclusively through Superchips internetupdate store**. And of course, Cortex deliversall the incredible performance resultsSuperchips customers have come to expectfrom the industry leader.
1950: 1999-2010 Mustang3.9L/4.0L/4.6L/5.4L2011-2012 Mustang 3.7L/5.0L1999-2011 F-Series Gas Trucks1999-2010 F-Series Diesel Trucks
2950: 1999-12 GM Gas Trucks2001-10 GM Diesel Trucks2008-09 Cobalt SS Turbo1999-02 Camaro SS & Z282010-11 Camaro SS1999-04 Corvette2006-08 Impala SS2006-08 Grand Prix GXP1999-02 Firebird/Trans AM
3950: 2005-09 Chrysler/Dodge Cars1998-10 Chrysler/Dodge
Gas Trucks1998.5-2009 Chrysler/Dodge
Diesel Trucks3870: 1998-2010 Jeep Wranger,
Grand Cherokee, Cherokee& Commander
** The Multivin feature currently covers Ford andGeneral Motors applications for an additional FEE.
Fuel13v4o_Layout 1 10/31/13 2:20 PM Page 117