pv quick start

PV Elite Quick Start

Version 2014 (16.0)

November 2013

DICAS-PE-200134B

2 PV Elite Quick Start

Copyright Copyright 2012-2013 Intergraph CAS, Inc. All Rights Reserved. Intergraph is part of Hexagon.

Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.

Contains RealDWG by Autodesk, Inc. Copyright 1998-2013 Autodesk, Inc. All rights reserved.

U.S. Government Restricted Rights Legend Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS 252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.

Unpublished - rights reserved under the copyright laws of the United States.

Intergraph Corporation 300 Intergraph Way Huntsville, AL 35813

Documentation Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides, Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a particular software product.

Other Documentation Other Documentation shall mean, whether in electronic or printed form and delivered with software or on eCustomer, SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph as guidance for using a software product.

Terms of Use a. Use of a software product and Documentation is subject to the End User License Agreement ("EULA") delivered with the

software product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the Licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use of this software product and Documentation. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the Documentation as defined in the applicable license agreement and delivered with the software product for Licensee's internal, non-commercial use. The Documentation may not be printed for resale or redistribution.

b. For use of Documentation or Other Documentation where end user does not receive a EULA or does not have a valid license agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other Documentation for Licensees internal non-commercial use. Intergraph Corporation gives Licensee permission to print a reasonable number of copies of Other Documentation for Licensees internal, non-commercial. The Other Documentation may not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and for any reason by Intergraph Corporation by giving written notice to Licensee.

Disclaimer of Warranties Except for any express warranties as may be stated in the EULA or separate license or separate terms and conditions, Intergraph Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its publication date.

The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.

PV Elite Quick Start 3

Limitation of Damages IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL, SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATIONS LIABILITY EXCEED THE AMOUNT THAT INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2) YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.

IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.

Export Controls Intergraph Corporations software products and any third-party Software Products obtained from Intergraph Corporation, its subsidiaries, or distributors (including any Documentation, Other Documentation or technical data related to these products) are subject to the export control laws and regulations of the United States. Diversion contrary to U.S. law is prohibited. These Software Products, and the direct product thereof, must not be exported or re-exported, directly or indirectly (including via remote access) under the following circumstances:

a. To Cuba, Iran, North Korea, Sudan, or Syria, or any national of these countries. b. To any person or entity listed on any U.S. government denial list, including but not limited to, the U.S. Department of Commerce

Denied Persons, Entities, and Unverified Lists, http://www,bis.doc.gov/complianceandenforcement/liststocheck.htm, the U.S. Department of Treasury Specially Designated Nationals List, www.treas.gov/offices/enforcement/ofac/http://www.pmddtc.state.gov/compliance/debar.html, and the U.S. Department of State Debarred List.

c. To any entity when Licensee knows, or has reason to know, the end use of the Software Product is related to the design, development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or sensitive nuclear uses.

d. To any entity when Licensee knows, or has reason to know, that an illegal reshipment will take place.

Any questions regarding export or re-export of these Software Products should be addressed to Intergraph Corporations Export Compliance Department, Huntsville, Alabama 35894, USA.

Trademarks Intergraph, the Intergraph logo, Intergraph Smart, PDS, SmartPlant, SmartMarine, FrameWorks, I-Sketch, IntelliShip, ISOGEN, SmartSketch, SPOOLGEN, SupportManager, and SupportModeler are trademarks or registered trademarks of Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. MicroStation is a registered trademark of Bentley Systems, Inc. Other brands and product names are trademarks of their respective owners.


Contents PV Elite Quick Start ..................................................................................................................................... 7

What's New in PV Elite and CodeCalc ................................................................................................... 9 Introduction ........................................................................................................................................... 11 Seminars ............................................................................................................................................... 11 Intergraph CAS Technical Support ....................................................................................................... 11 Licensing ............................................................................................................................................... 13

ESL Installation ............................................................................................................................... 14 SmartPlant License Manager Installation ....................................................................................... 17

Using the SmartPlant License Checkout Utility .................................................................................... 23 Install SmartPlant License Checkout Utility .................................................................................... 23 License Utility Checkout Dialog Box ............................................................................................... 24 Check Out a License for PV Elite ................................................................................................... 24

Installation ............................................................................................................................................. 27 Before You Begin PV Elite Installation ........................................................................................... 28 Installing PV Elite from the Product Media ..................................................................................... 29 Installing PV Elite in Silent Mode .................................................................................................... 29 Verifying the Installed Product Program Structure ......................................................................... 31

A Quick Look Around ................................................................................................................................ 32

Component Buttons .............................................................................................................................. 34 Building the Vessel from the Bottom Up ............................................................................................... 35 Dimensions ........................................................................................................................................... 36 Material Specification ............................................................................................................................ 40 Updating the Other Components in the Vessel .................................................................................... 42 The Status Bar at the Bottom of the Screen ......................................................................................... 44 The Output Processor ........................................................................................................................... 45 Generating and Printing the Final Pressure Vessel Report .................................................................. 46 Data Input Other information .............................................................................................................. 47 Design Constraints (Global Settings in PV Elite) .................................................................................. 49 Inserting a Component .......................................................................................................................... 53 Deleting a Component .......................................................................................................................... 54 Node Numbers ...................................................................................................................................... 54 Adding a Nozzle to the Model ............................................................................................................... 55 Nozzle Orientation Around the Vessel .................................................................................................. 57 Flip Model Orientation ........................................................................................................................... 58

Index ........................................................................................................................................................... 59

Contents



S E C T I O N 1

The PV Elite Quick Start provides you with a basic introduction to the PV Elite software, as well as details about licensing and installation. The second section of the Quick Start introduces you to important features of the interface and shows you the steps required to build a basic model. For more complete information about PV Elite, see the PV Elite Users Guide installed with your software.

In This Section What's New in PV Elite and CodeCalc .......................................... 9 Introduction .................................................................................... 11 Seminars ........................................................................................ 11 Intergraph CAS Technical Support ................................................ 11 Licensing ........................................................................................ 13 Using the SmartPlant License Checkout Utility ............................. 23 Installation ...................................................................................... 27



What's New in PV Elite and CodeCalc Below are the new features for Version 2014 (16.0) of PV Elite and CodeCalc. New features and improvements come directly from your comments, as well as updates to the previous version. This version of the software includes any new features or revisions made to the software for service packs on the 2013 version.

Code Updates and Analysis Changes ASME 2013 VIII-1 Edition updates incorporated ASME 2013 VIII-2 Edition updates incorporated ASME 2013 Section II Part D Edition updates added (included hundreds of changes and

additions)

PD 5500 2013 Addenda changes added BS EN 13445-3:2009+A1:2012 updates incorporated ASCE-2010 Wind/Seismic codes added IBC 2012 Wind/Seismic codes added NBC 2010 Wind/Seismic codes added

Internationalization Updates EN 1092 Flange Pressure Temperature Ratings updated (including PN 2.5 series) EN 1092 Flange Dimensional Data updated South African Wind Code added South African Seismic Code added User customizable G-loading option added

Productivity Enhancements Automatic File Backups added A new testing Program is included Smart Selections for ANSI/EN-1092 Flange Class/Grade Groups Updated Help documentation

Analysis Features TEMA Exchanger Analysis added back in CodeCalc software ASME Appendix 9 Type 2 Jackets added PD 5500 Type 2 Jackets added Nozzle FEA via NozzlePRO added back in CodeCalc software Direct UI support for EN-13445 Cold Spun Heads



QA Validation and Verification Additions The PV Elite development team continues to add new QA sample benchmark problems to

the benchmark solution set. In addition, QA Test now includes many new EN nozzle tests. PV Elite 2014 was benchmarked against ASME PTB-4 (ASME Section VIII-Division 1 Example Problem Manual). The Verification and Quality Assurance Manual was updated to include tables of comparison for various sample problems.


S E C T I O N 2

PV Elite is a package of 19 applications that work together to design and analyze pressure vessels and heat exchangers. The PV Elite software provides you with easy-to-use, technically-sound, and well-documented calculations that expedite and simplify vessel-design and re-rating tasks. The software also provides recent, industry-accepted analyses of the designs.

Calculations in PV Elite are based upon the latest editions of national codes, such as the ASME Boiler and Pressure Vessel Code or other relevant industry standards that are not covered directly by ASME VIII-1.

PV Elite Development Team continuously enhances the software to add new functionality and to modify existing procedures as industry codes are updated. For more information on the most recent changes to PV Elite, see What's New in PV Elite and CodeCalc (on page 9).

Seminars Intergraph CAS periodically offers seminars to augment your knowledge of PV Elite and of vessel and heat exchanger design and analysis. The general seminar is held in our Houston office and covers three days of material. This seminar emphasizes understanding the theories of analysis, the ASME code rules for certain components, and the design of components using the software.

Custom seminars held at client locations are also available. For additional seminar details, please contact the support staff at: [email protected].

Intergraph CAS Technical Support For the latest support information for this product:

Technical Support Email: [email protected]

ICAS Dealer Support: http://www.coade.com/Support/Dealers.shtml

Phone: 1-800-766-7701

Fax: 281-890-3301

Web Sites: http://www.coade.com http://www.intergraph.com/ppm/analysis.aspx

Address: Intergraph CAS 7840 N. Sam Houston Pkwy. W. Suite 100 Houston, TX 77064

Introduction

Introduction


Sales Email: [email protected]

Knowledge-Based Articles/Tutorials (US & Canada only):

http://crmweb.intergraph.com/ecustomer_enu

Send documentation comments or suggestions to [email protected].


S E C T I O N 3

PV Elite supports three types of licensing:

Local External Software Lock (ESL) - Hardware-based licensing using a green USB dongle. A local ESL can be moved between computers (such as between desktops and laptops).

Network External Software Lock (ESL) - Hardware-based licensing using a red USB dongle. A network ESL is installed on a computer that is network accessible from the computer, or multiple computers, running PV Elite.

License Manager - Software-based licensing using SmartPlant License Manager (SPLM). For more information, see SmartPlant License Manager Installation (on page 17). Refer to the SmartPlant License Manager documentation for complete installation and configuration instructions.

External Software Lock (ESL) Keys The External Software Lock (ESL) is the security protection method used by Intergraph CAS, Inc. The software cannot execute unless an appropriate ESL (green or red USB key) is connected locally to the computer, or to another computer in the network (red USB key).

The ESL contains the PV Elite licensing data, and other client-specific information. This information includes the client company name and user ID number. Additional data may be stored on the ESL depending on the specific program and the specific client.

There are two different ESL types, local and network. Both types of ESLs are intended to be attached to the USB ports of the applicable computers. The appropriate ESL(s) are shipped with your product according to the licensing type purchase.

Local ESLs provide the maximum flexibility in using the software in that they can be moved between computers (for example, between desktops and laptops).

Network ESLs must be attached to a computer on the network, either a computer or the server. In order for the network to respond to software requests for the ESL, the NetHASP License Manager utility must also be running on the computer where the network ESL is attached.

The HASP drivers for ESL usage can be found in the sub-directory ASSIDRV beneath the PV Elite program directory. The documentation files in this sub-directory contain instructions for a variety of networks and operating systems. Note that there are periodic updates to these ESL drivers and they can be downloaded from the Intergraph eCustomer (https://www.crmweb.intergraph.com) website.

Do not connect two locks to the same computer. The software finds the first lock and returns its code. For example, you have a lock for CAESAR II and CADWorx and plug both into the same computer. You start CAESAR II, but the software might find the CADWorx lock first and return an error. If the same computer is going to run more than one Intergraph CAS, Inc. product, then contact Intergraph CAS by sending an email to [email protected] to request that both products be licensed from the same lock.

Licensing

Licensing


ESL Installation The following topics explain how to install the different hardware locks supported by PV Elite.

What do you want to do? Install a local lock (on page 14) Install a network lock (on page 14)

Install a local lock 1. Open Windows Explorer.

2. If you are installing CAESAR II, PV Elite, or TANK, navigate to c:\Program Files\Intergraph CAS\Product\Assidrv and double-click HASPUserSetup.exe.

-OR-

If you are installing CADWorx, navigate to c:\CADWorx Version\Product\Assidrv and double-click HaspHLDriverSetup.exe

3. Follow the on-screen instructions to install the driver.

Install a network lock The following list details general information about red network ESLs.

The red network ESL should be set up by a Network Administrator or someone familiar with Windows-based networks. If you are not familiar with concepts such as network protocols, broadcast, IP addresses, TCP, UDP, and Windows Services, please do not attempt to setup the red network ESL.

The red network ESL does not have to be attached to the network server. We recommend attaching the red network ESL to a computer that is always up and running, can be re-booted without impact to users, and is not the primary computer for any user on the network.

If you install an Intergraph CAS product on a network drive for multiple users to access, assign read/write privileges for all users to the [Product Folder]\System folder. Intergraph CAS applications write temporary files to the [Product Folder]\System folder that pertains to the installation. The [Product Folder]\System folder also needs to have read/write privileges for all users.

If you are using other network protocols, such as NetBIOS or IPX, check the SafeNet web site for instructions. The only protocol tested with Intergraph CAS products is TCP/IP.

The information provided in PV Elite Help file is a supplement to the NetHasp User's Guide, which is delivered as a PDF(_NETHASP.pdf) in Assidrv folder. Review the PDF file for any issues not addressed in the Help file.

Licensing


Notes on Network ESLs A network ESL has advantages and disadvantages. One big advantage is that many client computers can access the software from a single server. Additional points for consideration are listed below.

Depending on the number of licenses allowed by the network ESL, some users may receive error messages when attempting to access the software. For example, if the ESL has been configured to allow four simultaneous users, an error message stating that no licenses are available when the fifth user attempts to access the software. Consequently, the fifth user is not able to access the software until one of the first four users exits the software and releases a license.

Because of the communication procedures between the client computer and the file server, memory access to the network ESL is much slower than to a local ESL. This access time delay only occurs when the software is first started after installation.

Because there is no network specific version of the software, the software looks first for a local ESL, and then for a network ESL. This allows both a network ESL and several local ESLs to be used on the same system. This transparent ESL access procedure allows a single version of the software to be used on the network and on remote computers.

We recommend that only 70 to 80 percent of the required licenses be assigned to a network ESL, with the remaining 20 to 30 percent assigned to local ESLs. This enables the local ESL to be moved between computers. If all of the licenses are on the network ESL, a user must be logged into the network to access the software. As such, a few local ESLs provide much greater operating flexibility.

NetHASP License Manager / NETHASP.INI Instructions You must have Administrator privileges to perform the following procedure.

1. Attach the red network hardware lock to the parallel port or USB port of the computer.

2. On the computer where the hardware lock is attached, navigate to the [Product Folder]\Assidrv folder and double click Lmsetup.exe. Follow the on-screen instructions to install the NetHASP License Manager as a service.

3. The NetHasp License Manager starts automatically each time you re-boot the computer. This occurs because the NetHasp License Manager is set up as a start up service inside Windows XP/Vista/7. To verify that the service is running, click Start > Control Manager > Administrative Services, and then double-click Services. In the Services dialog box, locate HASP Loader in the Name list. The HASP Loader Service starts even if no one logs into the computer.

4. Determine what protocols the NetHasp License Manager is listening to. The NetHasp License Manager displays a message similar to those list below:

Server is listening to IPX : Loaded Server is listening to TCP/IP : Loaded Server is listening to NetBIOS : Loaded

Loaded means that this protocol is active on the computer.

5. Open the Activity Log menu. This displays the activity log that confirms which protocols are loaded. Do not be alarmed if the activity log reports that the NHSRV.ini file is not found.

Licensing


6. Use the box in the top-left corner of the activity log to display only the information specific to each protocol. Open the activity log for the protocol you want to use, and verify that it contains no error messages.

7. For TCP/IP protocol, the activity log should report something similar to the following:

Server IP address: 111.111.111.111 Server Host Name: PDC_NT01

8. To speed up response time to the network key, use the Remove menu to unload any protocols that you are not planning to use with the NetHasp License Manager.

Modify NetHASP.ini for TCP/IP Protocol If you still cannot access the network ESL you need to configure this NetHASP.ini

file. You must know the IP address of the computer where the red network hardware lock is attached. All lines with a semi-colon at the start are considered not used.

1. Modify the NetHASP.ini file, located at in the [Product Folder]\Assidrv folder under [NH_COMMON], as follows:

a. NH_TCPIP = Enabled AND under [NH_TCPIP] b. NH_SERVER_ADDR = 111.111.111.111 c. NH_USE_BROADCAST = Disabled

You may also have to modify other entries in the [NH_TCPIP] section depending on your network setup. The most common entry to modify is NH_TCPIP_METHOD.

2. Copy the NetHASP.ini file to the AutoCAD folder.

Example: C:\Program Files\AutoCAD

Example: C:\Program Files\Autodesk\AutoCAD

3. For CADWorx Design, copy the NetHASP.ini file to the [Product Folder]\Intergraph CAS\CADWorx Design folder.

4. Start PV Elite .

Troubleshooting Network Locks 1. Verify that the NetHasp License Manager is running on the computer where the red network

ESL is attached.

2. Verify the protocols that NetHasp License Manager is broadcasting. Make sure that these protocols are installed on the client computers.

3. Install and run the Monitor Utility. This file, NetHASPMonitorSetup.exe, is located in the [Product Folder]Assidrv folder. If NetHASP Monitor cannot find the red network ESL, then PV Elite cannot find the red network ESL.

Licensing


SmartPlant License Manager Installation Before beginning the product installation, refer to the delivered SmartPlant License Manager readme file for the latest product installation updates. The readme file is delivered in the top level product folder of the product media. Be sure you have the latest version of the SmartPlant License Manager software before beginning the installation. If you do not have the latest version of the software, you can install it using http://ppmapps.intergraph.com/elicense (http://ppmapps.intergraph.com/elicense).

SmartPlant License Manager 2010 (v11) can be upgraded to SmartPlant License Manager 2012 (v12). Any existing license key will be invalidated after the upgrade to SmartPlant License Manager 2012 (v12). You will also need to generate a new computer ID and request a new key. If you upgrade the SmartPlant License Manager 2010 (v11) license computer to a SmartPlant License Manager 2012 (v12) client by mistake, you will have to un-install the SmartPlant License Manager client and reinstall SmartPlant License Manager 2012 (v12) license computer.

Hardware Configurations The SmartPlant License Manager licensing computer software should be installed on a stable, single node, hardware configuration (such as a simple PC), with a static IP address, because license key installation and license seat usage authentication depends on the information gathered from the physical hardware. Any automated changes that cause the hardware information not to match with the information used to generate the license key will result in a failure of the authentication process.

Virtual (including VMware), shadowed, mirrored, dynamic, or distributed hardware configurations cannot be used as a SmartPlant License Manager licensing computer. This includes terminal (application) servers, networked and distributed storage management systems, and so forth. When these specialized systems occur in the user's network, the SmartPlant License Manager Server licensing computer should be installed on a separate dedicated hardware configuration system. The SmartPlant License Manager licensing computer should be situated on the user's network where it can be accessed by all systems that are running application software that relies on the SmartPlant License Manager licensing computer for license management.

Multiple SmartPlant License Manager licensing computers can be used in the user's network as long as each system is a unique hardware system/installation. If SmartPlant License Manager licensing computers are cloned after the license key has been installed, then the license management will fail on the cloned system. Each SmartPlant License Manager licensing computer requires its own unique license key.

RAID (redundant array of independent disks) and SAN (storage area networks) are not

supported on a SmartPlant License Manager license computer.

The license computer must have the same version (or later) of SmartPlant License Manager installed as any client computers. In other words, you cannot use a newer version on a client computer to retrieve a license from an older version of SmartPlant License Manager on the licensing computer. The license computer must have the same version (or a newer version) installed than the clients.

You must log in as Administrator to install this software.

Licensing


1. Insert the Intergraph SmartPlant License Manager media. If the media does not start automatically, double-click Setup.exe in the root folder of the media.

During SmartPlant License Manager installation automatically turns on a product usage log file in C:\Win32App\Ingr\SPLM\bin\loggingfileV12.txt. You can change this location and name of this file as it can grow to be a large file. If you stop and restart logging, you need to define the output location.

This file can grow very large and users can redefine the location and name of this file.

2. Select SmartPlant License Manager Installation.

3. Click Next on the Welcome to the InstallShield Wizard for SmartPlant License Manager page.

4. Enter your name and company name in the User Name and Company Name fields on the Customer Information page. Click Next.

5. On the Software License Agreement page, select your country from the list and click Display to view the license agreement.

The license agreement is delivered as a PDF file.

6. Carefully read the license agreement. Close the PDF document, and click Yes on the License Agreement page to accept the terms.

7. Select either License Client or License Machine.

8. On the Choose Destination Location page, click Next to install SmartPlant License Manager in the default location. If you want to install the software in another location, click Change and select the new location.

It is recommended that you install SmartPlant License Manager using a path that contains no spaces, such as c:\win32app\Ingr (the default path).

9. Click Install on the Ready to Install the Program page. A status bar displays the progress of the installation on the Status Setup page.

10. Click Finish on the InstallShield Wizard Complete page to complete installation of SmartPlant License Manager.

Do not delete any files that are created during installation or as a result of using SmartPlant License Manager. Removal of any files causes the license system to fail and can require install, repair, or possibly removal and re-install of SmartPlant License Manager.

11. Add pdlice.exe to both the license computer and the client computer after installing of SPLM. You may need to remove pdlice.exe and re-add it if you uninstall and reinstall SPLM to upgrade SPLM from previous version to a current version. Otherwise, you may receive a Connection timed out error message when you start your application. You may also see the same error in your scavenging log file.

Licensing


Silent Mode and SmartPlant License Manager Installation

Quick Installation Workflow Use this workflow for all products that require SmartPlant License Manager concurrent licensing. The System Administrator completes or gives guidance about most of these steps. Administrator rights are required to install and setup SmartPlant License Manager. If you need more information, follow the detailed procedures in the other sections. For more information, refer to Frequently Asked Questions (FAQ), Functions of SmartPlant License Manager, and Troubleshooting and Error Messages.

Please refer to the delivered SmartPlant License Manager Readme for all the latest product installation updates.

1. Designate a computer as the SmartPlant License Manager license computer. This computer must be on the network and have a name with no spaces and a static IP address.

2. Install SmartPlant License Manager on the license computer and generate a computer ID.

3. Request a license key from the Intergraph Order Desk or generate a license key using eLicense.

4. Click Start > Programs > Intergraph SmartPlant License Manager > SmartPlant License Manager.

5. Click Install and Remove and Install License Key commands.

6. Click License Machine and enter the license key you received. If the license key installs correctly, SmartPlant License Manager software automatically closes.

7. Next, install SmartPlant License Manager on each client computer.

8. Click Start > Programs > Intergraph SmartPlant License Manager > SmartPlant License Manager.

9. Click Configure and Test and Select License Machine for Client.

10. Enter the SmartPlant License Manager computer name. Exit SmartPlant License Manager.

11. Install the software that requires licensing. For example, SmartPlant Review, PDS or SmartPlant P&ID. Use that product's installation and configuration guides to install each product.

12. Use the Test Seat Reservation and Test Seat Release commands to ensure that communication is working between the license computer and the client. Successful messages show appropriate communication.

13. Click Test Seat Reservation. Select the license computer name and Batch or Interactive mode. Note the seat number in the SmartPlant License Manager Information dialog box to enter.

14. Click Test Seat Release and enter the seat designated in the SmartPlant License Manager Information dialog box.

15. Start the software product that requires SmartPlant License Manager licensing.

16. For information about firewalls, please refer to Appendix E: Microsoft Windows Firewall and SmartPlant License Manager.

Licensing


See Also General Topics FAQ (on page 21)

Frequently Asked Questions (FAQ) Refer to the SmartPlant License Manager FAQ on the Web in the eCustomer system for the most current FAQ. It is continually updated. Click https://crmweb.intergraph.com/ecustomer_enu and select Services > Download Software Updates > Products > SPLM.

Will providing the Machine ID make my computer less secure?

No. The Machine ID allows the license manager to uniquely identify your computer from a collection of hardware and software identifiers without explicitly publishing your computer's TCPIP address. Because the computer identifier cannot be used like a TCPIP address, it is actually more secure than publishing your computer's TCPIP address.

Where can I find SmartPlant License Manager and other products to download?

SmartPlant License Manager is available from the following web page:

https://crmweb.intergraph.com

Select Services > Download Software Updates > Products > SPLM.

You do not need a serial number to install SmartPlant License Manager.

Can I divide the licenses for one LAN into several license computers for the purpose of managing project access, for example, or as coverage in the event that my license computer goes down?

Yes, you can divide the licenses.

What happens if I install the new license key prior to expiration of the old license key?

The new license will overwrite the existing key independent of the expiration date.

Is my existing key still running if I regenerate the Machine ID?

Yes, but you will not be able to reinstall the old key. You will need to request a new key for the new machine identifier.

See Also Purchasing Licenses FAQ (on page 20) General Topics FAQ (on page 21) PDS, FrameWorks Plus, and ISOGEN FAQ

Purchasing Licenses FAQ Do I have to request a software upgrade from my local office before requesting a license?

No, you can request licenses without upgrading the software. If you are upgrading software, you must request the upgrade before you request licenses. A license request does not include a software upgrade and a software upgrade does not include a license request.

See Also General Topics FAQ (on page 21)

Licensing


General Topics FAQ What is a license machine?

The license machine is the computer where the license key is loaded; it can be a standard computer or a server. The license key tells the license machine how many licenses it can issue. Clients of a license machine are computers where SmartPlant License Manager is installed and pointing to the license machine. The computer where you start the software (for example, PDS or SmartPlant P&ID) asks the license machine for a license. If a license is available, the license machine provides it. If all licenses are in use, the client is not granted a license.

How can I tell what version of SPLM was used in the Machine ID or license key file?

Please check the starting number in your Machine ID or license key. See the table below.

Version Machine ID starts with License key starts with

2012 (v12) 5 3

2010 (v11)

6 2

2008 (v10) 7 1

Do I have to have one license computer for each LAN?

No, your configuration is entirely up to you. A persistent network connection is required if you want to connect to a license server that belongs to a different LAN.

Can I make an educated guess at my installation date?

Yes. Intergraph provides a key within 48 hours of receipt of your request (via mail or phone). Please ensure that the date you request is the actual date that you install the key, making sure that all necessary software is available and loaded before that date. We request that you notify us as early as possible.

What happens if my license machine goes down?

You are unable to check out licenses from this machine until it is back in use. Processes that already have licenses checked out are not affected by the fact that the license computer is unavailable.

It is possible in critical situations to request emergency licenses from Intergraph. They are installed on the client computer rather than a licensing machine. Contact Intergraph Support at 1-800-766-7701 or your local Intergraph office for more information.

What happens if the license machine is rebooted in the middle of my design session?

Nothing. Licensing does not depend on maintaining a continuous communication link to the license computer.

What happens if my local computer goes down after I've obtained a license?

If the scavenger cannot contact the client computer during scavenging, the license is marked for a 16-hour hold before it is released. The scavenger periodically advances this 16-hour timer for each license. It is important to schedule the scavenger to run regularly, at

Licensing


least every hour or two. If the client is in contact sooner, the hold is voided and normal scavenging takes over.

I am running out of licenses earlier than I believe I should be. How can I troubleshoot to understand what is happening?

Have your users click Scavenge for Keys on the Scavenge Options dialog box or you can type pdlice -n in a Command Prompt window.

If you think that client nodes are improperly holding onto licenses, examine the results of the pdlice -M command. This shows you which client nodes have licenses checked out. If a client computer has no plant design-related activity and it is still holding licenses, rebooting that client and then scavenging from the license computer may free some licenses.

If possible, find out what was processing when the job stopped. This information can help you and/or Intergraph determine the underlying cause of the termination. Save the output of any scavenging process that returns a license. This information provides the reasons why the license was returned. The output of the scavenger includes the following information: nodename, product tag, batch mode (Yes/No), process ID, and checkout time.

What do I type to see the number of licenses?

Click Show Key Status from the Display Options dialog box to show the status of your keys.

How can I tell who is using a license?

Click Display Status of Reserved License on the Display Options dialog box or in the license log file.

We installed a key for three licenses, but we can operate only two licenses at the same time. Why?

There can be several reasons.

Click Display Status of Reserved License on the Display Options dialog box to determine the number of licenses that your key contains.

Click Scavenge for Keys on the Scavenge Options dialog box to scavenge for the third license that you are unable to use.

Verify that clients and servers can telnet to each other. Look for anomalies such as two nodes on the network with the same name or the reuse of an old name for a new computer, but with some traces of the old computer still existing in files on the network.

When an application is on a computer that is disconnected from the network without exiting the product, how long is the license held?

16 hours.

How long would a daily license last?

Daily license expires after 12 hours.

See Also Purchasing Licenses FAQ (on page 20)

Licensing


Using the SmartPlant License Checkout Utility The SmartPlant License Checkout utility (License Checkout Utility.exe) allows you to obtain licenses for Intergraph ICAS products for use on a non-networked computer (for example, a remote laptop). Using this utility allows you to run ICAS products without a network connection to the license machine. Each user on a server can check out a license from that server.

When you check out a license, the license and expiration information are stored on your local machine, separate from other license and expiration information. A license is available only for the user that checks out the license. Each time you start the product during the checkout period, a message displays the expiration date for the checked out license.

When the checkout period for the license expires, the ICAS product attempts to request a license using SmartPlant License Manager the next time you start the product. For example, after the license expires at 11:59 PM on the expiration date, the next time you start the product, it attempts to access the SmartPlant License Manager license machine for base and module licenses prior to running.

You must install and configure SmartPlant License Manager before checking out a license. You must have administrator privileges to setup and install the utility.

Install SmartPlant License Checkout Utility Do not uninstall the version of the SmartPlant License Checkout Utility that is

currently on your system if you (a) are installing a new product that includes SmartPlant License Checkout Utility v11, or (b) have other applications such as SmartPlant Review or SmartSketch loaded on your machine.

The older version of the SmartPlant License Checkout Utility is needed to work with your currently-loaded application(s). Refer to the compatibility matrix chart on ecustomer for information on application versions and their required version of the SmartPlant License Checkout Utility.

Install the Utility 1. Insert the product disc. If the installation does not start automatically, double-click setup.exe

in the main folder.

For ICAS products, locate the SmartPlant License Checkout Utility installation program in the Other Installs folder of the product DVD.

2. Click SmartPlant License Checkout Utility Installation.

3. Type your name and company name.

4. Verify your name and company name, and then click Next.

5. Click Display to read and accept the license agreement, and then click Yes.

You must have a PDF reader to view the license agreement.

6. Specify the destination folder.

Licensing


7. Review your settings, and then click Next.

8. Click Install to start the installation process.

9. Click Finish.

You can uninstall the License Checkout utility at any time, even if you are currently running

a product in remote license mode.

If you installed the latest version of the SmartPlant License Checkout Utility (v11), it is installed along with the older version you have:

License Utility Checkout Dialog Box Specifies the product for which you want to check out a license.

Options Application Group - Displays the installed products available for license checkout. Select the product for which you want to check out licenses.

If the Application Group list is empty, your application requires an older version of the checkout utility. Please check your original product installation media for the compatible version of the utility.

Available Modules - Displays any modules or add-ins available with your product. If no modules appear in the list, either your product contains no supported modules, or no modules have been installed. Check the box beside the module for which you want to check out a license, and then click Check Out. If you want to check out only the base product, do not check any of the modules.

License Expiration - Specifies the date that you want the checkout to expire. When the checkout period for the license expires, the product returns to normal and connected license operation using the SmartPlant License Manager the next time you start the product.

Check Out a License for PV Elite Be sure that the SmartPlant License Manager (SPLM) is installed and configured on your computer.

To check out a license for PV Elite 1. Click Start > Programs > Intergraph SmartPlant License Checkout Utility > License

Checkout Utility.

The SPLM Checkout Utility (see "License Utility Checkout Dialog Box" on page 24) dialog box opens.

2. In the Application Group list, select PV Elite.

You must close the PV Elite application when checking out a license.

Licensing


3. In the Available Modules list, click the checkbox for each module you need.

PV EliteI users must check out all listed PV Elite modules for the software to function correctly.

4. Select an expiration from the License Expiration list, and then click Check Out.

The checkout utility searches for an available license.

You may experience a delay as the utility checks the network for available licenses.

When you open PV Elite the status of the checkout license displays at the bottom of the PV Elite main window. When you are on the last day of your license checkout, the status displays you have zero days remaining.

Once you check out a license, it cannot be checked in. If you check out three modules (four total licenses: one base and three modules), then attempt to run the License Checkout Utility again and select two other modules, the software displays a dialog box that notifies you that a license is already checked out for PV Elite and displays the expiration date for that license.

When running in remote license mode, you cannot use setup to modify the product installation until the following conditions are met:

The checkout duration expires. The system is working with SmartPlant License Manager in connected license mode once

again.

In other words, you cannot install or remove modules while running in remote license mode.

If PV Elite is running in remote license mode but is unable to confirm for any reason that it is running in that mode, PV Elite automatically returns to connected license mode and attempts to obtain the licenses from SmartPlant License Manager. PV Elite notifies you if it is unable to obtain licenses from SmartPlant License Manager.

Each time you start PV Elite while using remote license mode, the software displays a message informing you when the checked out licenses expire. The first time that you run PV Elite after the checked out licenses expire, the software displays a message informing you that the checked out licenses have expired and that the software is reverting to the standard connected license mode and attempting to get licenses from SmartPlant License Manager.

Licensing



S E C T I O N 4

Prior to installing PV Elite, verify that your computer meets the required hardware and software requirements. For more information, see Before You Begin PV Elite Installation (on page 28)

The PV Elite installation DVD contains the following options:

Install PV Elite- Launches the main installation process, which installs PV Elite, the HASP drivers, and all associated documentation.

PV Elite Information - Opens the PV Elite Product Details page on the Intergraph CAS web site.

ReadMe File - Opens a text file discussing the installation steps, the system requirements, and the DVD contents.

License Agreement - Opens an RTF file containing the PV Elite License Agreement. HASP Network Licensing Overview - Opens a DOC file containing a summary of the

Aladdin (SafeNet) HASP Licensing System.

HASP Trouble Shooting - Opens a DOC file containing troubleshooting procedures for issues with HASP licensing.

DVD Content:

Browse the DVD - Displays the DVD contents in Windows Explorer. Additional Products - Displays additional Intergraph CAS products. Contact Intergraph - Displays contact information for Intergraph CAS Support. Services:

Training - Opens the PV Elite Course Details page on the Intergraph CAS web site. Support Forum - Opens the PV Elite Discussion Forum on the Intergraph CAS web site.

In This Section Before You Begin PV Elite Installation .......................................... 28 Installing PV Elite from the Product Media .................................... 29 Installing PV Elite in Silent Mode ................................................... 29 Verifying the Installed Product Program Structure ........................ 31

Installation

Installation


Before You Begin PV Elite Installation Verify that your system meets the requirements before installing PV Elite.

Close all other software before running the PV Elite installer. Most unsuccessful installations are caused by other software running at the same time as the installer.

Note that the product installation is a DVD. The product DVD is not readable in a CD drive. Verify that the software and hardware requirements are met.

Operating System Windows 7/8 Ultimate, Enterprise, or Professional (32-bit/64-bit)

You must enable .NET 3.5 prior to installing PV Elite on Windows 8 machines.

Windows XP Professional with SP3 (32-bit) Windows Server versions are only supported for the installation of network licensing

systems (NetHASP License Manager).

PV Elite is a native 32-bit application that runs with Windows 64-bit. CAESAR II does not support Windows 7/8 Starter, Home Basic, and Home Premium.

The software does not support Windows Vista Starter, Home Basic, Home Premium, Enterprise, Business, and Ultimate.

Processor Intel Pentium IV or higher AMD Athlon dual-core processor or higher 3.0 GHz or higher

Memory 2 GB RAM or higher for Windows XP 4 GB RAM or higher for Windows 7/8

Display Video card with at least 256MB video RAM Video card support for OpenGL 1.1 or later and DirectX 9.0 or later Video card drivers updated with the latest manufacturer's drivers 1280 x 1024 minimum resolution or higher with TrueColor Motherboard-integrated video cards are not recommended for desktop systems.

Remote Technologies Citrix XenApp 6.0 required on Windows Server 2008 R2 Enterprise

Installation


Installing PV Elite from the Product Media

Close all other software before running the PV Elite installer. Most unsuccessful installations are caused by other software running at the same time as the installer.

The installation DVD is not readable in a CD drive. 1. Insert the Intergraph PV Elite DVD. If the DVD does not start automatically, double-click

CDSpawn.exe in the root folder of the DVD.

The PV Elite launch screen opens in your default internet browser.

2. Click Install PV Elite.

3. Click Next on the Welcome to the Installation Wizard for PV Elite screen.

4. On the License Agreement screen, carefully read the license agreement.

5. Click I accept the terms in the license agreement, and then click Next.

6. On the Customer Information page, enter information in the User Name, Organization, and Serial number boxes. The serial number is provided to you by Intergraph CAS in your product shipment.

7. On the Destination Folder page, review the default folder path. If needed, click Change and select the folder location. Click Next.

8. On the Select License Type page, select the needed license type: network ESL, local ESL, or SPLM license. For more information, see Licensing (on page 13).

9. On the Ready to Install the Application screen, click Install to begin installing the software.

As the installation progresses, the status displays in a series of progress bars. If an ESL license type was selected, the Aladdin device driver installation begins. Click OK on each dialog box.

10. Click Finish to exit the installer.

11. In the Installer Information dialog box, click OK to restart the computer and complete the installation.

You must restart your computer for PV Elite to run correctly.

Installing PV Elite in Silent Mode You can use the Windows Installer to install and uninstall PV Elite using a command line instead of the normal installer interface. You can then perform an unattended installation without dialog boxes, such as when performing a network installation or a corporate repackaging. The following command line arguments and parameters can be used with Windows Installer (msiexec.exe) and the PV Elite setup (setup.exe) to perform a silent installation of the product.

1. Click Start > All Programs > Accessories > Command Prompt.

The Command Prompt screen opens.

2. Enter the drive letter where the PV Elite DVD is located. For example, type:

E:

Installation


3. Change the path to the PV Elite folder where Setup.exe is located on the DVD. For example, type:

cd PVElite_2011 4. Enter the installation command:

For silent installation with English language and green ESL color, type: Setup.exe /v"/qb INSTALL_SILENT="Yes" LANG="Eng" ESL_COLOR="Green""

For silent installation with Red ESL color and ESL installed locally, type: Setup.exe /v"/qb INSTALL_SILENT="Yes" LANG="Eng" ESL_COLOR="Red" ESL_ON_MACHINE="Yes""

For silent installation with SPLM, type: Setup.exe /v"/qb INSTALL_SILENT="Yes" LANG="Eng" ESL_COLOR="SPLM" SERIALNUMBER="""

Arguments /v - Pass msi commands

/qb - Silent installation with basic user interface

Parameters for Setup.exe INSTALL_SILENT - Sets silent installation.

Yes - Installation is silent. No - Normal installation dialog boxes appear. LANG - The language to install.

Eng - English Span - Spanish Ger - German Fren - French SERIALNUMBER - The product serial number provided to you by Intergraph CAS.

ESL_COLOR - The ESL license type.

Red - Network ESL Green - Local ESL SPLM - SmartPlant License Manager (no ESL) ESL_ON_MACHINE - Only used when ESL_COLOR is Red. Identifies the ESL location.

Yes - ESL is on the local machine. No - ESL is on the server. INSTALLDIR - The path to load the installation files.

The general format of the command is:

Installation


setup.exe /v"/qb PROPERTY_NAME="value" PROPERTY_NAME2="Value"" For a complete list of command line arguments for msiexec.exe, type the following in a

Command Prompt window: msiexec.exe /? For a complete list of command line arguments for setup.exe, type the following in a

Command Prompt window: setup.exe /?

Verifying the Installed Product Program Structure A typical PV Elite hard disk configuration is structured as follows after PV Elite completes installation:

PVELITE: Root Installation PV Elite directory

Project #1: Data files for Project #1

Project #2: Data files for Project #2

\SYSTEM: Program database & control files

\EXAMPLES: Sample input files

Most files in the data subfolders are identified by a user-defined filename with a given extension. The remaining files hold data controlling the software's operation. These files and their description follow:

jobname.pvdb PV Elite input file

jobname.PVU Form information results file

jobname.TAB Temporary results file

jobname.T80 Results file used by the output review processor

jobname.CCI Input file for component analysis

units.FIL User units file (relating user's units and program units)

*.BIN PV Elite Material Database

UMAT1.BIN Binary file holding the user-defined materials

A Quick Look Around


This section shows you the most important features of the new interface, and shows the step-by-step procedures required to build a model. Not every aspect of the data entry is covered, but this section of the guide gives you enough information to understand the basic principles. Refer to the PV Elite documentation for more information about the different fields in the interface.

After you have PV Elite running, you will see this screen:

A Quick Look Around

A Quick Look Around


Before getting into any details, let us build a simple vertical vessel. Our first vessel has three parts as shown below:

The vessel is built in PV Elite from the bottom to the top; or, the case of a horizontal vessel, from left to right. We will build a horizontal vessel later. This shows how the vessel is built:

A Quick Look Around


Component Buttons Near the top of the main window on the Home tab, there is a row of buttons called Element panel:

Working from left to right, the components referred are:

Cylindrical Shell

Hemispherical Head

Ellipse Head (Ellipsoidal Head)

Torispherical Head (F & D Head)

Conical Head or Transition

Welded Flat Head

We will talk about the remaining commands later as I am sure you are anxious to start building your first vessel. Before we leave this subject however, if you let your mouse cursor hover over any of the buttons, you will get a tool tip, which briefly describes the function of the button:

A Quick Look Around


Building the Vessel from the Bottom Up 1. Click Ellipse to place the bottom head.

2. Click Cylinder to place the main shell.

3. Click Ellipse again to place the top head.

If you look at the window to the right, your 3D model should look like this.

4. You can switch to the 3D view by selecting the 3D View tab under the model representation.

5. If you want to go back to the 2D view, click the 2D View tab.

A Quick Look Around


Dimensions PV Elite populates the height and other dimensions for your vessel with sample data, which you can alter to your vessel specifics. PV Elite made certain assumptions as you built the model, including diameter, thicknesses, lengths, and materials.

1. Before we look at the dimensions, select the bottom head in either the 2D or 3D model. This will select the bottom head as the current component.

If you look at the 2D model, you will see that the bottom head is a lighter color.

A Quick Look Around


2. Let us look at the dimensions PV Elite chose for the current component (the lighter color in the illustration above). The details will look like this:

Here are the major assumptions for this example:

Inside Diameter: 96 inches Straight Flange: 0.1667 feet (which is 2 inches) Finished Thickness: 0.25 inches Internal Corrosion: 0.125 inches External Corrosion: 0 Internal Pressure: 100 psi External Pressure: 15 psi Temperatures: 100 F Head Aspect Ratio: 2 (Head Factor)

There is other information, but let us make some changes to suit our vessel. First we change the dimensions and the pressure:

A Quick Look Around


New Values:

Inside Diameter: 60 inches Finished Thickness: 0.5 inches Internal Corrosion: 0.0625 inches External Corrosion: 0.0625 inches Internal Pressure: 120 psi Temperatures: 200 F

Your screen might look different, but follow along, and it will become clear. If you are accustomed to working in the metric system, we shall address that situation shortly.

1. Click on the left side of the Inside Diameter field:

2. Now, enter the new diameter by typing 60:

3. Next, press the Enter key on your keyboard twice to move the cursor down to the next field:

A Quick Look Around


4. If you do not want to change the straight flange, press Enter again, and it will move to the next field. You should be able to complete the entries for your new dimensions:

A Quick Look Around


Material Specification Now we are going to change the material from SA-516 70 to SA 240 316L.

1. In the Material Name field, type SA240316L. Don't worry about spaces or dashes.

A new dialog displays.

2. Select the first entry in the list.

A Quick Look Around


The Material Properties dialog displays.

This screen gives you information about the material you have chosen.

3. Click Select and the material for your bottom head will change as follows:

A Quick Look Around


Updating the Other Components in the Vessel So far, we have entered the new data for the bottom head element. Also, if you look at the screen you will see the geometry difference of your bottom head to the rest of the elements:

The vessel looks like this because we have not updated the remaining components (main shell and top head) data fields. We are going to use a shortcut to copy the values for the bottom to the remaining components.

1. Click Share Information located in the Utility panel of the Home tab.

A Quick Look Around


The Data Share Dialog displays.

Notice the boxes that have been checked. The checked items will be shared with all the other upper components. Make sure you have checked only the boxes shown in this example.

2. Click OK.

PV Elite updates all the components with the new data.

Your model now looks more realistic. You can see that at least the diameter of the bottom head has been shared with the main shell and top head.

A Quick Look Around


The Status Bar at the Bottom of the Screen So far we have only entered the data relevant to our vessel, and produced the model on the screen. In this section, you'll understand the Status Bar fields.

1. Select the main shell in either the 2D or 3D view.

The main shell element is highlighted.

2. Look at the bottom of the screen to the status bar:

The status bar gives us a lot of information for the selected component. Let us consider the fields from left to right:

El# 2 of 3 : Component number 2 of 3 components (from the bottom) Fr: 0.00 To: 4.00 ft : Element spans from 0.00 ft to 4.00 ft from the datum line Up: : Element orientation Tr: 0.3420 : Computed thickness for the internal pressure (120 psi) Mawp: 206.8 : MAWP for this element (206.8 psi) MAPnc: 275.6 : Maximum allowable pressure new and cold (275.6 psi) Trext: 0.328 : Computed thickness for the external pressure Slen: 22.7 ft : Maximum unsupported length for the external pressure

Let us now see what happens when there is a problem with an element.

3. Go to Finished Thickness field, and change the thickness from 0.5 inches to 0.2 inches.

4. Now look at the status bar at the bottom of the screen:

The required thickness for the internal and external pressures now appears in red, indicating that there is a problem. In our case, the problem is the thickness.

5. Change the thickness back to 0.5 inches to fix the problem.

A Quick Look Around


The Output Processor Now that we have built our simple model, we need to get the complete details of the calculations performed by PV Elite.

Click Save and save your model using the name My Vertical Vessel.

1. Click Analyze .

When the analysis finishes, the Output Processor displays.

Your screen may look different, but it can easily be changed to look like the illustration above.

The left window has the heading Report List. In the right window is the prompt Select one or more reports from the Report List to view or print.

2. Click Internal Pressure Calculations from the list.

A Quick Look Around


The right pane now shows the results of the item you selected in the left window pane. The output window now looks as shown below.

3. You can scroll up and down to look at the complete calculation for the internal pressure

computations.

Generating and Printing the Final Pressure Vessel Report

Now that we have looked at the output for the Internal Pressure Calculations, we will learn how to include different items in your final report.

1. While holding down the CTRL key on your keyboard, click on the items that you want included from the Report List (left) window.

2. After you select the items, we are ready to generate the report.

A Quick Look Around


3. If you want to send the output to a printer, then click Print . This prints the report immediately with page numbers and headings on each page.

There are other options. For example, you might find it convenient to send the output to Microsoft Word if you have it installed on your computer. This feature allows you to edit the results and add your own notes or comments.

You can also send the output to a text file by selecting Print to file. You are prompted for a file name. This will be a text file with a filename extension of .txt. You will be able to access this file with any text editor such as Notepad, or Microsoft Word. When you send the output to a text file, all the colored text will be lost, and will simply be in black font color.

Data Input Other information If you look at the bottom of the Data Input screen, you will see a series of tabs:

Notice that the General Input tab is selected. This tab refers to the basic dimensional, pressure, temperature, and material selection for the currently selected element. You can show and hide tabs as needed using Input on the Home tab.

1. Click Input , and then select Heading.

2. Select the Heading tab.

A Quick Look Around


3. Enter information for Line 1, Line 2, and Line 3 that you want to appear at the top of each and every page of the report.

4. Click Browse at the end of the Title Page field.

5. In the Title Page Text dialog, enter any information that you want to appear on the Title Page when sent to the printer or to a file. This will overwrite the information PV Elite would otherwise print by default:

A Quick Look Around


Design Constraints (Global Settings in PV Elite) Use the Design Constraints tab to set the default values for the entire vessel. By entering the pressures and temperatures in these first four fields, PV Elite will use these values as the default values for the whole vessel. This saves time later.

Some of the other design constraints that you might what to consider are discussed below.

Datum Line Options 1. Click the 3D View tab.

PV Elite has located the datum line at the tangent line of the bottom head. We can change the location of the datum line at any time to move it to a more convenient location.

A Quick Look Around


2. Click Browse at the end of the Datum Line Options field.

3. Type 3 for the Vertical Vessels offset, and then click OK. This sets the datum line to 3 feet up from its current location.

After you have a skirt attached to the bottom of the vessel, you might want to move the

datum line to the bottom of the skirt.

Hydrotest Type and Position of the Hydrotest Select the type of hydrotest. For Division 1, the software provides three different methods to determine hydrotest pressure. For Division 2, the program provides two hydrotest methods. Select one of the following:

UG-99b - ASME UG-99 (b), Division 1. The hydrotest pressure is 1.3 times (1.5 for pre-99 addenda) the maximum allowable working pressure for the vessel multiplied by the lowest ratio of the stress value S for the test temperature to the stress value S for the design temperature. This type of hydrotest is normally used for non-carbon steel vessels where the allowable stress changes with temperature, starting even at a somewhat low temperature.

UG-99c - ASME UG-99(c), Division 1. The hydrotest pressure is determined by multiplying the minimum MAP by 1.3 (1.5 for pre-99 addenda) and reducing this value by the hydrostatic head on that part. The hydrostatic head is calculated based on the dimensions of the vessel and by values for Projection from Top, Projection from Bottom, and Projection from Bottom Oper. In addition, Hydrotest Position is used to determine the head pressure.

UG-99b(34) - ASME UG-99(b), footnote 34, Division 1. The hydrotest pressure is 1.3 times (1.5 for pre-99 addenda) the design pressure for the entire vessel, multiplied by the lowest ratio of the stress value Sa for the test temperature to the stress value S for the design temperature.

UG-100 - ASME UG-100 pneumatic test. The test pressure is 1.1 times (1.25 for pre-99 addenda) the stated design pressure for the entire vessel, multiplied by the lowest ratio of the stress value Sa for the test temperature to the stress value S for the design temperature.

The stress ratio mentioned above includes bolt allowable stresses for flanges that are designed according to Appendix 2. This will usually result in a ratio of 1. See ASME Interpretation VIII-1-83-260 for more information. Click Tools > Configuration to turn off this option, resulting in a ratio greater than one in cases where the operating and ambient stresses for the vessel parts are not the same.

AT-300 - ASME AT-300, Division 2, based on vessel design pressure. The hydrotest pressure is 1.25 times the design pressure to be marked on the vessel, multiplied by the lowest ratio of the stress intensity value Sm for the test temperature to the stress intensity

A Quick Look Around


value Sm for the design temperature. This type of hydrotest is normally used for non-carbon steel vessels where the allowable stress changes with temperature starting even at a somewhat low temperature.

AT-301 - ASME AT-301, Division 2, based on calculated pressure. A hydrostatic test based on a calculated pressure may be used by agreement between the user and the manufacturer. The hydrostatic test pressure at the top of the vessel is the minimum of the test pressures calculated by multiplying the basis for calculated test pressure for each element by 1.25 and reducing this value by the hydrostatic head on that element.

No Hydro - No hydrotest pressure. User Entered Pressure 1.43 * MAWP (PED) The next box lets you specify which position the vessel will be during the hydrotest:

Select a hydrotest position. This input is required so that the total static head can be determined and subtracted when UG-99c is selected for Hydrotest Type. This value is used in conjunction with Projection from Top, Projection from Bottom, and Flange Distance to Top to determine the total static head. Select from the following:

Vertical - The vessel is tested in the upright or vertical position. This is not common. Horizontal - The vessel is tested in the horizontal position. This is common for most

vessels. The vessel is on its side (in the case of a vertical vessel) or in its normal position (for a horizontal vessel).

Tall towers for example, are usually hydrotested in the horizontal position. PV Elite has to compute the hydrostatic pressure from the water in the vessel at hydrotest time. If the vessel is tested in the vertical positions, the pressure at the bottom of the vessel will be greater than if the vessel is tested in the horizontal position. Give careful consideration to the position that is appropriate to your situation.

Miscellaneous Weight % Enter a percentage value to include additional weight to account for vessel attachments and internal items not otherwise included in the vessel. Typical values are 3.0 or 5.0. The software multiplies the total weight of the vessel by 1.0 plus this value converted to a decimal (such as 1.03 or 1.05). Enter 0 if no additional weight is needed.

A Quick Look Around


Design Code PV Elite allows the user to perform vessel calculations in several pressure vessel codes. Use the Design Code field on the Home tab in the Units/Code panel to change the design code.

PV Elite supports the following design codes:

ASME Section VIII, Division 1 ASME Section VIII, Division 2 British Code PD 5500 European Code EN 13445 After you select a code, you will have to re-select the materials because each code has its own design stress tables.

Is this a Heat Exchanger If the Dimensional Solutions 3D file interface button is selected, also select this option to write geometry and loading information for this vessel design to the .ini file created in the current working directory. See Dimensional Solutions http://www.Dimsoln.com for more information about the Dimensional Solutions product line. This entry is optional.

To completely define an exchanger it is necessary to enter in the required information regarding the tubes, tubesheets and the floating head (if any). With the exchanger data, PV Elite can then compute the weights and required thicknesses of the exchanger components. For more information, see Tubesheet.

This check box is optional.

ASME Steel Stack Select to perform an ASME steel stack analysis, based on the ASME recommended guidelines for Steel Stacks STS-2000 with addenda. This analysis is for circular stacks that meet the design requirements in the steel stack guidelines. The results are shown in the ASME STS Stack Calculations report. If Design Code is not set to Division 1 (ASME VIII-1), the stack analysis is not performed.

Also select this option if you are analyzing a steel stack and want to check it against ANSI/ASME STS-2000/STS-1a-2003. After the software completes the calculation, the program generates the Stress Due to Combined Loads report with a listing of the stack calculations. Compressive allowables in the report are calculated based on Section 4.4.

A Quick Look Around


When selected, expand ASME Steel Stack and enter values for ASCE Wind Exposure, Factor of Safety, Mean Hourly Wind Speed, Is the Stack Lined?, and Importance Factor.

Read and understand the ASME stack guidelines. This is not a code like ASME Division 1 or 2, but a set of design guidelines for designers and engineers.

The following paragraphs from the stack guidelines are addressed:

4.4 Allowable Stresses 4.4.1 Longitudinal Compression, equations 4.7,4.8 and 4.9 4.4.2 Longitudinal Compression and Bending 4.4.3 Circumferential Stresses 4.4.4 Combined Longitudinal and Circumferential Compressive Stresses 4.4.5 Circumferential Compression in Stiffeners, equations 4.14, 4.15, 4.16 4.4.7 Minimum Structural Plate Thickness 5.2.2 Wind Responses, equations 5.3, 5.4 and (1),(2) and (3), (b) equations 5.5, 5.6 and 5.7

Design Modification

If any of the modifications is set to yes, PV Elite will correct the item should it fail in the analysis. For example, if Select Wall Thickness for Internal Pressure was set to Yes, PV Elite will automatically increase the thickness of a component should it not be thick enough.

Inserting a Component 1. In the 2D View, select the component below or above where you want to insert the new

component.

2. Click Insert Element on the Home tab.

A Quick Look Around


The Insert New Element dialog displays.

3. Select the type of element you want to insert.

4. Select Before or After as needed.

5. Click OK.

Deleting a Component 1. In the 2D View, select the component to delete.

Make sure there are no nozzles on this component.

2. Click Delete on the Home tab.

3. Click Yes to confirm that you want to delete the component.

Node Numbers All elements that make up a vessel exist between nodes. On the top part of the General Input tab are two fields that indicate From Node and To Node:

A Quick Look Around


Every main element (not attachments such as nozzles) has two nodes. Consider these two vessels shown below:

Notice that every element from the bottom to the top or from the left to the right exists between two node numbers. There is a From Node, and there is a To Node. In the case of the bottom (or left) head, the nodes are situated at the tangent line and the weld line.

Adding a Nozzle to the Model 1. Switch to the 2D View.

2. Select the component into which you want to add the nozzle.

3. Click Nozzle Input on the Home tab.

The Nozzle Input/Analysis dialog box displays.

Different nozzle configurations can be considered. The choices are basically nozzles without pads, nozzles with pads, protruding nozzles without pads, and protruding nozzles with pads. There are also special forged nozzles available for analysis.

4. Select the default nozzle attachment.

5. Click on the nozzle description field and change the description name of your nozzle to N1.

A Quick Look Around


6. Select the next fields or press ENTER on your keyboard past the Diameter field to run your nozzle calculation. If your inputs fail the design code, you will notice the red warnings on the status bar at the bottom of the dialog box.

Also at the bottom of the Nozzle Analysis dialog box, you will see a calculator button below the status bar.

7. Click the calculator button to open the Quick Results Dialog. This screen will give you a

quick calculation report of your current nozzle:

A Quick Look Around


Nozzle Orientation Around the Vessel Let's look at the orientation of the nozzle around the vessel.

A Quick Look Around


From the example shown above, the 0 position is at the top (North) and the nozzle at position 90 is to the right. Therefore, the angles of the nozzle increase in the clockwise direction. However the zero position can occupy the North, West or East position as you need. The angle can increase in the clockwise or the counter-clockwise direction. The controls are on the Configuration dialog screen. To get the Configuration dialog screen, go to the Tools tab, click Set Configuration Parameters, and then select the Set Default Values tab.

Flip Model Orientation If a new model is built in the vertical position and it needs to change orientation to the horizontal position for different analysis purposes; PV Elite is able to flip the model with a single button found on the Tools tab, Flip Model Orientation .


A A Quick Look Around 32 Adding a Nozzle to the Model 55

B Before You Begin PV Elite Installation 28 Building the Vessel from the Bottom Up 35

C Check Out a License for PV Elite 24 Component Buttons 34

D Data Input Other information 47 Deleting a Component 54 Design Constraints (Global Settings

in PV Elite) 49 Dimensions 36

E ESL Installation 14

F Flip Model Orientation 58 Frequently Asked Questions (FAQ) 20

G General Topics FAQ 21 Generating and Printing the Final Pressure

Vessel Report 46

I Inserting a Component 53 Install a local lock 14 Install a network lock 14 Install SmartPlant License Checkout

Utility 23 Installation 27 Installing PV Elite from the Product

Media 29 Installing PV Elite in Silent Mode 29 Intergraph CAS Technical Support 11 Introduction 11

L License Utility Checkout Dialog Box 24 Licensing 13

M Material Specification 40

N NetHASP License Manager / NETHASP.INI

Instructions 15 Node Numbers 54 Notes on Network ESLs 15 Nozzle Orientation Around the Vessel 57

P Purchasing Licenses FAQ 20 PV Elite Quick Start 7

Q Quick Installation Workflow 19

S Seminars 11 SmartPlant License Manager

Installation 17

T The Output Processor 45 The Status Bar at the Bottom of the

Screen 44 Troubleshooting Network Locks 16

U Updating the Other Components in the

Vessel 42 Using the SmartPlant License Checkout

Utility 23

Index

Index


V Verifying the Installed Product Program

Structure 31

W What's New in PV Elite and CodeCalc 9

PV Elite Quick StartWhat's New in PV Elite and CodeCalc

IntroductionSeminarsIntergraph CAS Technical Support

LicensingESL InstallationInstall a local lockInstall a network lockNotes on Network ESLsNetHASP License Manager / NETHASP.INI InstructionsTroubleshooting Network Locks

SmartPlant License Manager InstallationSilent Mode and SmartPlant License Manager InstallationQuick Installation WorkflowFrequently Asked Questions (FAQ)Purchasing Licenses FAQGeneral Topics FAQ

Using the SmartPlant License Checkout UtilityInstall SmartPlant License Checkout UtilityLicense Utility Checkout Dialog BoxCheck Out a License for PV Elite

InstallationBefore You Begin PV Elite InstallationInstalling PV Elite from the Product MediaInstalling PV Elite in Silent ModeVerifying the Installed Product Program Structure

A Quick Look AroundComponent ButtonsBuilding the Vessel from the Bottom UpDimensionsMaterial SpecificationUpdating the Other Components in the VesselThe Status Bar at the Bottom of the ScreenThe Output ProcessorGenerating and Printing the Final Pressure Vessel ReportData Input Other informationDesign Constraints (Global Settings in PV Elite)Inserting a ComponentDeleting a ComponentNode NumbersAdding a Nozzle to the ModelNozzle Orientation Around the VesselFlip Model Orientation

Index

pv quick start

Documents

documentation documentation

use of documentation

intergraph corporation

particular software

restricted computer

intergraph cas

valid license agreement

applicable license agreement