quick guide quick start guide

of 1/1
1 1 2 3 4 Cypress TME Board Quick Start Guide Power DC Adaptor 12V/2A System CD 2 3 4 Quick Guide Quick Start Guide PSoC Thermal Management Expansion Board Kit 雙銅紙 A4 100P 雙面印 中間一刀裁 完成尺寸 148.5X210 出單請打上料號 CPT-3076-01 Quick Guide hat’s in the Box? W 1 umper Settings J 4 ME module installation CY8CKIT-001 T 2 CPT-3076-01 Jumper Default Setting J2 J3 SINGLE PWM_TMP DUAL 3.3V VDDIO 5V 3-pin header to choose between single sensor or dual sensor (daisy chain) connection for the PWM temperature sensors. Place jumper in 1-2 position to enable dual sensor daisy-chain mode. 3-pin header to set logic signal levels for digital temperature sensors. Place in 1-2 for 5V interfacing. Place in 2-3 position to 3.3V interfacing. J9 12V_DVK 12V 12V_EXT 3-pin header for fan power supply. Place in 1-2 position to source external power from the power jack (J13). Place in 2-3 position to source 12V power from the DVK. http://tme.terasic.com http://www.cypress.com/go/CY8CKIT-036 I2C Temperature Sensor 1-Wire Temperature Sensor 4-Wire Fan Socket I2C/SMBus/PMBus Port 2x20 Pin Headers PWM Temperature Sensor Diode Temperature Sensor Power Jack Insert the kit CD and install the kit software • View the User’s Guide for detailed instructions • During the install, continue with hardware setup 1 Set “VDD DIG” and “VDD ANLG” to 3.3V using SW3, J6 and J7 on the CY8CKIT-001 2 Ensure LCD Power jumper (J12) is set to ON and the LCD display is plugged into the DVK 3 Connect VR to P1_2, SW1 to P1_4 and SW2 to P1_5 on the breadboard area of the CY8CKIT-001 and ensure J11 is set with a jumper. 4 Program the PSoC Thermal Management Demo 5 Run the PSoC Thermal Management Demo 6 ME module installation CY8CKIT-030 T 3 Insert the kit CD and install the kit software 1 Set VDDD and VDDA to 3.3V by placing jumpers in 1-2 position of J10 and J11. Enable POT_PWR by installing a jumper on J30 of the CY8CKIT-030 2 Program the PSoC Thermal Management Demo 3 Remove the USB cable from the CY8CKIT-030 and plug the TME EBK into Port E 4 Select 12V_EXT with J9 in the 1-2 position on the TME EBK. Then plug in the 12V/2A power supply into the TME EBK at J13.Connect the USB cable to J1 on the CY8CKIT-030. 5 Run the PSoC Thermal Management Demo 6 www.terasic.com • Connect the Miniprog3 to the PSoC 3 processor module. • Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-001_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files". • Remove power to the DVK, plug the TME EBK into Port A of the DVK and re-apply power to the DVK and EBK using the provided power adapter(s) • Use SW1 to navigate between the thermal management screens on the LCD • Refer to the User’s Guide example 3 for project details and additional thermal management solutions • View the User’s Guide for detailed instructions • During the install, continue with hardware setup • Connect the USB cable to J1 on the CY8CKIT-030. • Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-030_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files". • Use SW2 to navigate between the thermal management screens on the LCD • Refer to the User’s Guide example 3 for project details and additional thermal management solutions. PSoC Thermal Management Expansion Board Kit CY8CKIT-036 J30 NOTE: This kit requires one of the following kits to operate: 1.CY8CKIT-001 PSoC Development Kit 2.CY8CKIT-030 PSoC 3 Development Kit CAUTION: DO NOT plug in TME board-follow instructions in Step 6 CAUTION: DO NOT plug in TME board-follow instructions in Step 4 For support, please contact us at: Online:www.cypress.com/go/support Telephone (24x7): +1-800-541-4736 ext. 8 (USA) or +1-408-943-2600 ext. 8 (International) For additional information visit: http://www.cypress.com/go/CY8CKIT-036 or http://tme.terasic.com

Post on 02-Jan-2017

259 views

Category:

Documents

5 download

Embed Size (px)

TRANSCRIPT

  • 11

    2

    3

    4

    Cypress TME Board

    Quick Start Guide

    Power DC Adaptor 12V/2A

    System CD

    2

    3 4

    Quick GuideQuick Start Guide

    PSoC Thermal Management Expansion Board Kit

    A4 100P 148.5X210 CPT-3076-01

    Quick Guidehats in the Box?W1

    umper SettingsJ4

    ME module installation CY8CKIT-001T2

    CPT-3076-01

    Jumper Default Setting

    J2

    J3

    SINGLE

    PWM_TMP

    DUAL

    3.3V

    VD

    DIO

    5V

    3-pin header to choose between single sensor or

    dual sensor (daisy chain) connection for the PWM

    temperature sensors. Place jumper in 1-2 position

    to enable dual sensor daisy-chain mode.

    3-pin header to set logic signal levels for digital

    temperature sensors. Place in 1-2 for 5V interfacing.

    Place in 2-3 position to 3.3V interfacing.

    J9

    12V_D

    VK

    12V

    12V_E

    XT

    3-pin header for fan power supply. Place in 1-2

    position to source external power from the power

    jack (J13). Place in 2-3 position to source 12V

    power from the DVK.

    http://tme.terasic.comhttp://www.cypress.com/go/CY8CKIT-036

    I2C Temperature Sensor

    1-Wire Temperature Sensor

    4-Wire FanSocket

    I2C/SMBus/PMBus Port

    2x20 Pin Headers

    PWMTemperature

    Sensor

    Diode TemperatureSensor

    Power Jack

    Insert the kit CD and install the kit software View the Users Guide for detailed instructions During the install, continue with hardware setup

    1 Set VDD DIG and VDD ANLG to 3.3V using SW3, J6 and J7 on the CY8CKIT-001

    2

    Ensure LCD Power jumper (J12) is set to ON and the LCD display is plugged into the DVK

    3 Connect VR to P1_2, SW1 to P1_4 and SW2 to P1_5 on the breadboard area of the CY8CKIT-001 and ensure J11 is set with a jumper.

    4

    Program the PSoC Thermal Management Demo

    5 Run the PSoC Thermal Management Demo

    6

    ME module installation CY8CKIT-030T3

    Insert the kit CD and install the kit software

    1 Set VDDD and VDDA to 3.3V by placing jumpers in 1-2 position of J10 and J11. Enable POT_PWR by installing a jumper on J30 of the CY8CKIT-030

    2

    Program the PSoC Thermal Management Demo

    3 Remove the USB cable from the CY8CKIT-030 and plug the TME EBK into Port E

    4

    Select 12V_EXT with J9 in the 1-2 position on the TME EBK. Then plug in the 12V/2A power supply into the TME EBK at J13.Connect the USB cable to J1 on the CY8CKIT-030.

    5 Run the PSoC Thermal Management Demo

    6

    www.terasic.com

    Connect the Miniprog3 to the PSoC 3 processor module.

    Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-001_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files".

    Remove power to the DVK, plug the TME EBK into Port A of the DVK and re-apply power to the DVK and EBK using the provided power adapter(s)

    Use SW1 to navigate between the thermal management screens on the LCD

    Refer to the Users Guide example 3 for project details and additional thermal management solutions

    View the Users Guide for detailed instructions During the install, continue with hardware setup

    Connect the USB cable to J1 on the CY8CKIT-030.

    Using the PSoC Programmer software, program the PSoC device with the "Thermal_Demo-030_rev1.hex" file located at "C:\Program Files\Terasic\PSoC Thermal Management EBK\1.0\Firmware\Hex_Files".

    Use SW2 to navigate between the thermal management screens on the LCD

    Refer to the Users Guide example 3 for project details and additional thermal management solutions.

    PSoCThermal Management

    Expansion Board Kit CY8CKIT-036

    J30

    NOTE: This kit requires one of the following kits to

    operate:

    1.CY8CKIT-001 PSoC Development Kit

    2.CY8CKIT-030 PSoC 3 Development Kit

    CAUTION: DO NOTplug in TME board-follow

    instructions in Step 6

    CAUTION: DO NOT plug in TME board-follow

    instructions in Step 4

    For support, please contact us at:

    Online:www.cypress.com/go/support

    Telephone (24x7): +1-800-541-4736 ext. 8 (USA) or +1-408-943-2600 ext. 8 (International)

    For additional information visit:http://www.cypress.com/go/CY8CKIT-036 or http://tme.terasic.com