mx series ethernet services router dpc guide

73
MX Series Ethernet Services Router DPC Guide July 2009 1

Upload: techdude

Post on 05-Dec-2014

935 views

Category:

Documents


1 download

DESCRIPTION

 

TRANSCRIPT

Page 1: MX Series Ethernet Services Router DPC Guide

MX Series Ethernet Services RouterDPC Guide

July 2009

■ 1

Page 2: MX Series Ethernet Services Router DPC Guide

Contents MX Series DPC Overview ................................................................................3DPCs Supported on MX Series Routers ............................................................4Gigabit Ethernet DPC with SFP ........................................................................6Gigabit Ethernet Enhanced DPC with SFP .......................................................8Gigabit Ethernet Enhanced Ethernet Services DPC with SFP .........................10Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with SFP ...........12Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP ....................1410-Gigabit Ethernet DPC with XFP ................................................................1710-Gigabit Ethernet Enhanced DPCs with XFP ..............................................1910-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP ....................2110-Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with XFP ......2310-Gigabit Ethernet Enhanced Queuing IP Services DPC with XFP ................25Multi-Rate Ethernet Enhanced DPC with SFP and XFP ..................................27Multi-Rate Ethernet Enhanced Ethernet Services DPC with SFP and XFP ......30Multi-Rate Ethernet Enhanced Queuing IP Services DPC with SFP and

XFP .........................................................................................................32MultiServices DPC .........................................................................................34Tri-Rate Enhanced DPC .................................................................................36Tri-Rate Enhanced Ethernet Services DPC .....................................................38MX Series DPC Protocol and Application Support ..........................................40

Protocols and Applications Supported by MX Series DPCs and EnhancedDPCs (DPC and DPCE-R) ..................................................................40

Protocols and Applications Supported by MX Series Enhanced EthernetServices DPCs (DPCE-X) ...................................................................46

Protocols and Applications Supported by MX Series Enhanced QueuingIP Services DPCs (DPCE-R-Q) ...........................................................50

Protocols and Applications Supported by MX Series Enhanced QueuingEthernet Services DPCs (DPCE-X-Q) .................................................54

Protocols and Applications Supported by the MX Series MultiServicesDPC (MS-DPC) ..................................................................................58

Optical Interface Specifications .....................................................................60Small Form-Factor Pluggable (SFP) Optical Interface Specifications

(MX Series Routers) ..........................................................................60Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface

Specifications (MX Series Routers) ....................................................6510-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface

Specifications (MX Series Routers) ....................................................68JUNOS Documentation and Release Notes ....................................................71Requesting Technical Support .......................................................................71

Self-Help Online Tools and Resources .....................................................71Opening a Case with JTAC ......................................................................72

Revision History ............................................................................................72

2 ■

MX Series Ethernet Services Router DPC Guide

Page 3: MX Series Ethernet Services Router DPC Guide

MX Series DPC Overview

A DPC provides multiple physical interfaces and Packet Forwarding Engines on asingle board that installs into a slot within the MX Series Ethernet Services Routers.A DPC receives incoming packets from the network and sends outgoing packets tothe network. The Packet Forwarding Engines on a DPC are equipped withpurpose-built ASICs that perform packet processing and forwarding.

When a slot is not occupied by a DPC, you must insert a blank DPC to fill the emptyslot and ensure proper cooling of the system. For complete information aboutinstalling and handling DPCs, see the hardware guide for your router.

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

MX Series DPC Overview ■ 3

MX Series DPC Overview

Page 4: MX Series Ethernet Services Router DPC Guide

DPCs Supported on MX Series Routers

Table 1 on page 4 lists the DPCs supported by the MX Series Ethernet Servicesrouters.

Table 1: DPCs Supported in the MX Series Ethernet Services Routers

First JUNOSSupport

MaximumThroughputper DPCPortsDPC Model NumberDPC Name

8.240 Gbps40DPC-R-40GE-SFP“Gigabit Ethernet DPC with SFP” on page 6

8.440 Gbps40DPCE-R-40GE-SFP“Gigabit Ethernet Enhanced DPC with SFP” on page8

8.440 Gbps40DPCE-X-40GE-SFP“Gigabit Ethernet Enhanced Ethernet Services DPCwith SFP” on page 10

8.540 Gbps40DPCE-X-Q-40GE-SFP“Gigabit Ethernet Enhanced Queuing Ethernet ServicesDPC with SFP” on page 12

9.120 Gbps20DPCE-R-Q-20GE-SFP“Gigabit Ethernet Enhanced Queuing IP Services DPCswith SFP” on page 14

8.540 Gbps40DPCE-R-Q-40GE-SFP“Gigabit Ethernet Enhanced Queuing IP Services DPCswith SFP” on page 14

8.240 Gbps4DPC-R-4XGE-XFP“10-Gigabit Ethernet DPC with XFP” on page 17

9.120 Gbps2DPCE-R-2XGE-XFP“10-Gigabit Ethernet Enhanced DPCs with XFP” onpage 19

8.440 Gbps4DPCE-R-4XGE-XFP“10-Gigabit Ethernet Enhanced DPCs with XFP” onpage 19

8.440 Gbps4DPCE-X-4XGE-XFP“10-Gigabit Ethernet Enhanced Ethernet Services DPCwith XFP” on page 21

8.540 Gbps4DPCE-X-Q-4XGE-XFP“10-Gigabit Ethernet Enhanced Queuing EthernetServices DPC with XFP” on page 23

8.540 Gbps4DPCE-R-Q-4XGE-XFP“10-Gigabit Ethernet Enhanced Queuing IP ServicesDPC with XFP” on page 25

9.240 Gbps22DPCE-R-20GE-2XGE“Multi-Rate Ethernet Enhanced DPC with SFP and XFP”on page 27

9.240 Gbps22DPCE-X-20GE-2XGE“Multi-Rate Ethernet Enhanced Ethernet Services DPCwith SFP and XFP” on page 30

9.340 Gbps22DPCE-R-Q-20GE-2XGE“Multi-Rate Ethernet Enhanced Queuing IP ServicesDPC with SFP and XFP” on page 32

9.3–2 (Notsupported)

MS-DPC“MultiServices DPC” on page 34

4 ■ DPCs Supported on MX Series Routers

MX Series Ethernet Services Router DPC Guide

Page 5: MX Series Ethernet Services Router DPC Guide

Table 1: DPCs Supported in the MX Series Ethernet Services Routers (continued)

First JUNOSSupport

MaximumThroughputper DPCPortsDPC Model NumberDPC Name

9.140 Gbps40DPCE-R-40GE-TX“Tri-Rate Enhanced DPC” on page 36

9.140 Gbps40DPCE-X-40GE-TX“Tri-Rate Enhanced Ethernet Services DPC” on page38

Related Topics ■ MX Series DPC Overview on page 3

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

DPCs Supported on MX Series Routers ■ 5

DPCs Supported on MX Series Routers

Page 6: MX Series Ethernet Services Router DPC Guide

Gigabit Ethernet DPC with SFP

■ JUNOS 8.2 and laterSoftware release

■ 40 Gigabit Ethernet ports

■ Power requirement: 6.98 A @ 48 V (335 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds up to 1 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

Hardware features

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

6 ■ Gigabit Ethernet DPC with SFP

MX Series Ethernet Services Router DPC Guide

Page 7: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

NOTE: Do not install Gigabit Ethernet SFPs in the SONET/SDH port. The port will not recognizethe SFP.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 2/0 for 2/0 through 2/4

■ 2/5 for 2/5 through 2/9

■ 3/0 for 3/0 through 3/4

■ 3/5 for 3/5 through 3/9

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Gigabit Ethernet DPC with SFP ■ 7

Gigabit Ethernet DPC with SFP

Page 8: MX Series Ethernet Services Router DPC Guide

Gigabit Ethernet Enhanced DPC with SFP

■ JUNOS 8.4 and laterSoftware release

■ 40 Gigabit Ethernet ports

■ Power requirement: 6.98 A @ 48 V (335 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds up to 1 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

8 ■ Gigabit Ethernet Enhanced DPC with SFP

MX Series Ethernet Services Router DPC Guide

Page 9: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

NOTE: Do not install Gigabit Ethernet SFPs in the SONET/SDH port. The port will not recognizethe SFP.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 2/0 for 2/0 through 2/4

■ 2/5 for 2/5 through 2/9

■ 3/0 for 3/0 through 3/4

■ 3/5 for 3/5 through 3/9

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Gigabit Ethernet Enhanced DPC with SFP ■ 9

Gigabit Ethernet Enhanced DPC with SFP

Page 10: MX Series Ethernet Services Router DPC Guide

Gigabit Ethernet Enhanced Ethernet Services DPC with SFP

■ JUNOS 8.4 and laterSoftware release

■ 40 Gigabit Ethernet ports

■ Power requirement: 6.98 A @ 48 V (335 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds up to 1 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs(DPCE-X)” on page 46 for information about the protocols and applications that this DPCsupports.

NOTE: The routing table is limited to 32,000 IP routes. This limitation applies to any manner inwhich the routes are learned, such as OSPF, RIP, and so on. The DPC supports BGP for L2 VPNsonly.

Software features

10 ■ Gigabit Ethernet Enhanced Ethernet Services DPC with SFP

MX Series Ethernet Services Router DPC Guide

Page 11: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

NOTE: Do not install Gigabit Ethernet SFPs in the SONET/SDH port. The port will not recognizethe SFP.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 2/0 for 2/0 through 2/4

■ 2/5 for 2/5 through 2/9

■ 3/0 for 3/0 through 3/4

■ 3/5 for 3/5 through 3/9

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Gigabit Ethernet Enhanced Ethernet Services DPC with SFP ■ 11

Gigabit Ethernet Enhanced Ethernet Services DPC with SFP

Page 12: MX Series Ethernet Services Router DPC Guide

Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with SFP

■ JUNOS 8.5 and laterSoftware release

■ 40 Gigabit Ethernet ports

■ Power requirement: 7.38 A @ 48 V (354 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds up to 1 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q)” on page 54 for information about the protocols and applicationsthat this DPC supports.

NOTE: The routing table is limited to 32,000 IP routes. This limitation applies to any manner inwhich the routes are learned, such as OSPF, RIP, and so on. The DPC supports BGP for L2 VPNsonly.

Software features

12 ■ Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with SFP

MX Series Ethernet Services Router DPC Guide

Page 13: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

NOTE: Do not install Gigabit Ethernet SFPs in the SONET/SDH port. The port will not recognizethe SFP.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 2/0 for 2/0 through 2/4

■ 2/5 for 2/5 through 2/9

■ 3/0 for 3/0 through 3/4

■ 3/5 for 3/5 through 3/9

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with SFP ■ 13

Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with SFP

Page 14: MX Series Ethernet Services Router DPC Guide

Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP

Figure 2: 40-Port GigabitEthernet Enhanced QueuingIP Services DPC with SFP

Figure 1: 20-Port GigabitEthernet Enhanced QueuingIP Services DPC with SFP

1/0

■ 20-port: JUNOS 9.1 and later

■ 40-port: JUNOS 8.5 and later

Software release

■ 20 or 40 Gigabit Ethernet ports

■ Power requirement:

■ 20-port: 4.0 A @ 48 V (190 W)

■ 40-port: 7.38 A @ 48 V (354 W)

■ Weight:

■ 20-port: 13 lb (5.9 kg)

■ 40-port: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds up to 1 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

14 ■ Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP

MX Series Ethernet Services Router DPC Guide

Page 15: MX Series Ethernet Services Router DPC Guide

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q)” on page 50 for information about the protocols and applications thatthis DPC supports.

Software features

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

NOTE: Do not install Gigabit Ethernet SFPs in the SONET/SDH port. The port will not recognizethe SFP.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Link LEDs are labeled in groups of five:

■ 20-port:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 40-port:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

■ 2/0 for 2/0 through 2/4

■ 2/5 for 2/5 through 2/9

■ 3/0 for 3/0 through 3/4

■ 3/5 for 3/5 through 3/9

LEDs

Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP ■ 15

Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP

Page 16: MX Series Ethernet Services Router DPC Guide

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

16 ■ Gigabit Ethernet Enhanced Queuing IP Services DPCs with SFP

MX Series Ethernet Services Router DPC Guide

Page 17: MX Series Ethernet Services Router DPC Guide

10-Gigabit Ethernet DPC with XFP

■ JUNOS 8.2 and laterSoftware release

■ Four 10-Gigabit Ethernet ports

■ Power requirement: 6.46 A @ 48 V (310 W)

■ Weight: 13.1 lb (5.9 kg)

Description

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

Hardware features

■ Configurable WAN-PHY mode options

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

10-Gigabit Ethernet DPC with XFP ■ 17

10-Gigabit Ethernet DPC with XFP

Page 18: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Tunnel LED, one green per port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom 0/0 through 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

18 ■ 10-Gigabit Ethernet DPC with XFP

MX Series Ethernet Services Router DPC Guide

Page 19: MX Series Ethernet Services Router DPC Guide

10-Gigabit Ethernet Enhanced DPCs with XFP

Figure 4: 4-Port 10-GigabitEthernet Enhanced DPCwith XFP

Figure 3: 2-Port 10-GigabitEthernet Enhanced DPCwith XFP

■ 2-port: JUNOS 9.1 and later

■ 4-port: JUNOS 8.4 and later

Software release

■ Two or four 10-Gigabit Ethernet ports

■ Power requirement:

■ 2-port: 3.5 A @ 48 V (170 W)

■ 4-port: 6.46 A @ 48 V (310 W)

■ Weight:

■ 2-port: 12 lb (5.4 kg)

■ 4-port: 13.1 lb (5.9 kg)

Description

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

10-Gigabit Ethernet Enhanced DPCs with XFP ■ 19

10-Gigabit Ethernet Enhanced DPCs with XFP

Page 20: MX Series Ethernet Services Router DPC Guide

■ Configurable WAN-PHY mode options

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Tunnel LED, one green per port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom:

■ 2-port: 0/0 through 1/0

■ 4-port: 0/0 through 3/0

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

20 ■ 10-Gigabit Ethernet Enhanced DPCs with XFP

MX Series Ethernet Services Router DPC Guide

Page 21: MX Series Ethernet Services Router DPC Guide

10-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP

■ JUNOS 8.4 and laterSoftware release

■ Four 10-Gigabit Ethernet ports

■ Power requirement: 6.46 A @ 48 V (310 W)

■ Weight: 13.1 lb (5.9 kg)

Description

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Configurable WAN-PHY mode options

■ See “Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs(DPCE-X)” on page 46 for information about the protocols and applications that this DPCsupports.

NOTE: The routing table is limited to 32,000 IP routes. This limitation applies to any manner inwhich the routes are learned, such as OSPF, RIP, and so on. The DPC supports BGP for L2 VPNsonly.

Software features

10-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP ■ 21

10-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP

Page 22: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Tunnel LED, one green per port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom 0/0 through 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

22 ■ 10-Gigabit Ethernet Enhanced Ethernet Services DPC with XFP

MX Series Ethernet Services Router DPC Guide

Page 23: MX Series Ethernet Services Router DPC Guide

10-Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with XFP

■ JUNOS 8.5 and laterSoftware release

■ Four 10-Gigabit Ethernet ports

■ Power requirement: 6.63 A @ 48 V (318 W)

■ Weight: 13.1 lb (5.9 kg)

Description

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Configurable WAN-PHY mode options

■ See “Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q)” on page 54 for information about the protocols and applicationsthat this DPC supports.

NOTE: The routing table is limited to 32,000 IP routes. This limitation applies to any manner inwhich the routes are learned, such as OSPF, RIP, and so on. The DPC supports BGP for L2 VPNsonly.

Software features

10-Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with XFP ■ 23

10-Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with XFP

Page 24: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Tunnel LED, one green per port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom 0/0 through 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

24 ■ 10-Gigabit Ethernet Enhanced Queuing Ethernet Services DPC with XFP

MX Series Ethernet Services Router DPC Guide

Page 25: MX Series Ethernet Services Router DPC Guide

10-Gigabit Ethernet Enhanced Queuing IP Services DPC with XFP

■ JUNOS 8.5 and laterSoftware release

■ Four 10-Gigabit Ethernet ports

■ Power requirement: 6.63 A @ 48 V (318 W)

■ Weight: 13.1 lb (5.9 kg)

Description

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Configurable WAN-PHY mode options

■ See “Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q)” on page 50 for information about the protocols and applications thatthis DPC supports.

Software features

10-Gigabit Ethernet Enhanced Queuing IP Services DPC with XFP ■ 25

10-Gigabit Ethernet Enhanced Queuing IP Services DPC with XFP

Page 26: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

Tunnel LED, one green per port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

Link LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

The Tunnel and Link LEDs are labeled top to bottom 0/0 through 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

26 ■ 10-Gigabit Ethernet Enhanced Queuing IP Services DPC with XFP

MX Series Ethernet Services Router DPC Guide

Page 27: MX Series Ethernet Services Router DPC Guide

Multi-Rate Ethernet Enhanced DPC with SFP and XFP

■ JUNOS 9.2 and laterSoftware release

■ 20 Gigabit Ethernet ports

■ 2 10-Gigabit Ethernet ports

■ Power requirement: 6.94 A @ 48 V (333 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ SFP ports:

■ High-performance throughput on each port at speeds up to 1 Gbps

■ XFP ports:

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

Multi-Rate Ethernet Enhanced DPC with SFP and XFP ■ 27

Multi-Rate Ethernet Enhanced DPC with SFP and XFP

Page 28: MX Series Ethernet Services Router DPC Guide

■ Configurable WAN-PHY mode options

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

■ 10/100/1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 100Base-BX

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

28 ■ Multi-Rate Ethernet Enhanced DPC with SFP and XFP

MX Series Ethernet Services Router DPC Guide

Page 29: MX Series Ethernet Services Router DPC Guide

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

LINK LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

TUNNEL LED, one green per XFP port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

The SFP Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

The XFP ports are labeled top to bottom 2/0 and 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Multi-Rate Ethernet Enhanced DPC with SFP and XFP ■ 29

Multi-Rate Ethernet Enhanced DPC with SFP and XFP

Page 30: MX Series Ethernet Services Router DPC Guide

Multi-Rate Ethernet Enhanced Ethernet Services DPC with SFP and XFP

■ JUNOS 9.2 and laterSoftware release

■ 20 Gigabit Ethernet ports

■ 2 10-Gigabit Ethernet ports

■ Power requirement: 6.94 A @ 48 V (333 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ SFP ports:

■ High-performance throughput on each port at speeds up to 1 Gbps

■ XFP ports:

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Configurable WAN-PHY mode options

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs(DPCE-X)” on page 46 for information about the protocols and applications that this DPCsupports.

Software features

30 ■ Multi-Rate Ethernet Enhanced Ethernet Services DPC with SFP and XFP

MX Series Ethernet Services Router DPC Guide

Page 31: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

■ 10/100/1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 100Base-BX

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

LINK LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

TUNNEL LED, one green per XFP port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

The SFP Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

The XFP ports are labeled top to bottom 2/0 and 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Multi-Rate Ethernet Enhanced Ethernet Services DPC with SFP and XFP ■ 31

Multi-Rate Ethernet Enhanced Ethernet Services DPC with SFP and XFP

Page 32: MX Series Ethernet Services Router DPC Guide

Multi-Rate Ethernet Enhanced Queuing IP Services DPC with SFP and XFP

■ JUNOS 9.3 and laterSoftware release

■ 20 Gigabit Ethernet ports

■ 2 10-Gigabit Ethernet ports

■ Power requirement: 6.94 A @ 48 V (333 W)

■ Weight: 13.1 lb (5.9 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ SFP ports:

■ High-performance throughput on each port at speeds up to 1 Gbps

■ XFP ports:

■ High-performance throughput on each port at speeds up to 10 Gbps

■ WAN-PHY mode at 9.953 Gbps

■ LAN-PHY mode at 10.3125 Gbps

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ Configurable WAN-PHY mode options

■ Optical diagnostics and related alarms

■ See “Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q)” on page 50 for information about the protocols and applications thatthis DPC supports.

Software features

32 ■ Multi-Rate Ethernet Enhanced Queuing IP Services DPC with SFP and XFP

MX Series Ethernet Services Router DPC Guide

Page 33: MX Series Ethernet Services Router DPC Guide

■ You can install any transceiver supported by the DPC. For information about installing andremoving transceivers, see the hardware guide for your router.

■ Duplex LC/PC connector (Rx and Tx)

■ Small form-factor pluggable (SFP) transceivers:

■ 1000Base-EX

■ 1000Base-LH

■ 1000Base-LX

■ 1000Base-SX

■ 1000Base-T

■ 10/100/1000Base-T

Optical interface specifications—see “Small Form-Factor Pluggable (SFP) Optical InterfaceSpecifications (MX Series Routers)” on page 60

■ Bidirectional small form-factor pluggable (SFP) transceivers:

■ 100Base-BX

■ 1000Base-BX

Optical interface specifications—see “Bidirectional Small Form-Factor Pluggable (SFP) OpticalInterface Specifications (MX Series Routers)” on page 65

■ Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

■ 10-GBase-E

■ 10-GBase-L

■ 10-GBase-S

■ 10-GBase-Z

Optical interface specifications—see “10-Gigabit Small Form-Factor Pluggable (XFP) OpticalInterface Specifications (MX Series Routers)” on page 68

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

LINK LED, one green per port:

■ Off—No link.

■ On steadily—Link is active.

TUNNEL LED, one green per XFP port:

■ Off—Normal operating mode.

■ On steadily—Port configured in tunnel mode.

The SFP Link LEDs are labeled in groups of five:

■ 0/0 for 0/0 through 0/4

■ 0/5 for 0/5 through 0/9

■ 1/0 for 1/0 through 1/4

■ 1/5 for 1/5 through 1/9

The XFP ports are labeled top to bottom 2/0 and 3/0.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Multi-Rate Ethernet Enhanced Queuing IP Services DPC with SFP and XFP ■ 33

Multi-Rate Ethernet Enhanced Queuing IP Services DPC with SFP and XFP

Page 34: MX Series Ethernet Services Router DPC Guide

MultiServices DPC

■ JUNOS 9.3 and laterSoftware release

■ Power requirement: 5.52 A @ 48 V (265 W)

■ Weight: 14.7 lb (6.7 kg)

■ Supports tunnel services. This feature is included with the DPC and does not require anindividual license.

■ Individual licenses must be purchased for additional services.

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

■ Maximum number of supported DPCs:

■ MX240 router: 2

■ MX480 router: 4

■ MX960 router: 4

Description

■ Active monitoring on up to 10 million flows

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Two MultiServices Processing Units (MSPUs) per DPC, which include two 1.1Ghz multicoreCPUs, each with 4GB of memory for processing integrated services

Hardware features

■ Support for up to 12,000 service sets

■ See “Protocols and Applications Supported by the MX Series MultiServices DPC (MS-DPC)”on page 58 for information about the protocols and applications that this DPC supports.

Software features

■ SFPs are not supported.Cables and connectors

34 ■ MultiServices DPC

MX Series Ethernet Services Router DPC Guide

Page 35: MX Series Ethernet Services Router DPC Guide

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

STATUS LED, one tricolor per MSPU:

■ Off—MSPU is offline. If both MSPUs are offline it is safe to remove the DPC from the chassis.

■ Green—MSPU is operating normally.

■ Yellow—MSPU is initializing.

■ Red—MSPU has an error or failure.

Application (APP) LED, one tricolor per MSPU:

■ Off—Service is not running on the MSPU.

■ Green—Service is running on the MSPU under acceptable load.

■ Yellow—Service on the MSPU is overloaded.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

MultiServices DPC ■ 35

MultiServices DPC

Page 36: MX Series Ethernet Services Router DPC Guide

Tri-Rate Enhanced DPC

■ JUNOS 9.1 and laterSoftware release

■ 40 autonegotiating 10Base-T, 100Base-TX, or 1000Base-T Megabit Ethernet ports

■ Power requirement: 6.67 A @ 48 V (320 W)

■ Weight: 14.5 lb (6.6 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds of 10 Mbps, 100 Mbps, or 1000 Mbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ See “Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPCand DPCE-R)” on page 40 for information about the protocols and applications that thisDPC supports.

Software features

36 ■ Tri-Rate Enhanced DPC

MX Series Ethernet Services Router DPC Guide

Page 37: MX Series Ethernet Services Router DPC Guide

■ Connector: Four-pair, Category 5 shielded twisted-pair connectivity through an RJ-45connector

■ Pinout:

■ JUNOS 9.1: MDI

■ JUNOS 9.2 and later: MDI, MDI crossover

■ Maximum distance: 328 ft/100 m

NOTE: Do not use RJ-45 cables with strain-relief boots exceeding 1.5 mm from the bottom ofthe connector. Cable boots that exceed this measurement can damage the port.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

ACT LED, one green per port:

■ Off—No active traffic.

■ Flashing—Link is active.

SPD LED, one bicolor:

■ Green—DPC is functioning in 1000Base-T mode.

■ Yellow—DPC is functioning in 10Base-T or 100Base-TX mode.

■ Off—No link.

The ACT and SPD LEDs are located on either side of the ports labeled horizontally and top tobottom 0/0 through 3/9.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Tri-Rate Enhanced DPC ■ 37

Tri-Rate Enhanced DPC

Page 38: MX Series Ethernet Services Router DPC Guide

Tri-Rate Enhanced Ethernet Services DPC

■ JUNOS 9.1 and laterSoftware release

■ 40 autonegotiating 10Base-T, 100Base-TX, or 1000Base-T Megabit Ethernet ports

■ Power requirement: 6.67 A @ 48 V (320 W)

■ Weight: 14.5 lb (6.6 kg)

■ Supports large Ethernet frame sizes for more efficient throughput across the intra-POPnetwork

Description

■ High-performance throughput on each port at speeds of 10 Mbps, 100 Mbps, or 1000 Mbps

■ Autonegotiation between Gigabit Ethernet circuit partners

■ Full-duplex mode

■ Maximum transmission units (MTUs) of up to 9192 bytes

■ Enhanced ASICs for increased performance and scalability of Layer 2 features

Hardware features

■ See “Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs(DPCE-X)” on page 46 for information about the protocols and applications that this DPCsupports.

Software features

38 ■ Tri-Rate Enhanced Ethernet Services DPC

MX Series Ethernet Services Router DPC Guide

Page 39: MX Series Ethernet Services Router DPC Guide

■ Connector: Four-pair, Category 5 shielded twisted-pair connectivity through an RJ-45connector

■ Pinout:

■ JUNOS 9.1: MDI

■ JUNOS 9.2 and later: MDI, MDI crossover

■ Maximum distance: 328 ft/100 m

NOTE: Do not use RJ-45 cables with strain-relief boots exceeding 1.5 mm from the bottom ofthe connector. Cable boots that exceed this measurement can damage the port.

Cables and connectors

OK/FAIL LED, one bicolor:

■ Green—DPC is functioning normally.

■ Red—DPC has failed.

ACT LED, one green per port:

■ Off—No active traffic.

■ Flashing—Link is active.

SPD LED, one bicolor:

■ Green—DPC is functioning in 1000Base-T mode.

■ Yellow—DPC is functioning in 10Base-T or 100Base-TX mode.

■ Off—No link.

The ACT and SPD LEDs are located on either side of the ports labeled horizontally and top tobottom 0/0 through 3/9.

LEDs

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Tri-Rate Enhanced Ethernet Services DPC ■ 39

Tri-Rate Enhanced Ethernet Services DPC

Page 40: MX Series Ethernet Services Router DPC Guide

MX Series DPC Protocol and Application Support

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC andDPCE-R)

Table 2 on page 40 contains the first JUNOS support for protocols and applicationson the MX Series DPCs and Enhanced DPCs. A dash indicates that the protocol orapplication is not supported.

Table 2: Protocols and Applications Supported by the MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

DPCE-R-20GE-2XGEDPCE-R-40GE-TX

DPCE-R-4XGE-XFP

DPCE-R-40GE-SFPDPCE-R-2XGE-XFP

DPC-R-4XGE-XFP

DPC-R-40GE-SFP

Multi-RateEnhanced DPC

Tri-RateEnhanced DPC

Enhanced DPCEnhanced DPCDPCName

Protocol or Application

9.49.49.49.49.4Access Node ControlProtocol (ANCP)

9.29.18.49.18.2Accepts traffic destined forGRE tunnels or DVMRP(IP-in-IP) tunnels

9.29.18.49.18.2Bidirectional ForwardingDetection protocol (BFD)

9.29.18.49.18.2Border Gateway Protocol(BGP)

9.29.18.49.18.2BGP/Multiprotocol LabelSwitching (MPLS) virtualprivate networks (VPNs)

40 ■ MX Series DPC Protocol and Application Support

MX Series Ethernet Services Router DPC Guide

Page 41: MX Series Ethernet Services Router DPC Guide

Table 2: Protocols and Applications Supported by the MX Series DPCs and Enhanced DPCs (DPC andDPCE-R) (continued)

DPCE-R-20GE-2XGEDPCE-R-40GE-TX

DPCE-R-4XGE-XFP

DPCE-R-40GE-SFPDPCE-R-2XGE-XFP

DPC-R-4XGE-XFP

DPC-R-40GE-SFP

9.29.18.49.18.2Distance Vector MulticastRouting Protocol (DVMRP)and generic routingencapsulation (GRE)support—access side andserver side

9.29.18.49.18.4IEEE 802.1ag EthernetOAM Continuity Checkprotocol

9.29.19.09.19.0IEEE 802.1ag EthernetOAM Linktrace protocol

9.29.19.19.19.1IEEE 802.1ag EthernetOAM Loopback protocol

9.29.18.49.18.2Firewall filters

9.29.18.49.18.2Flexible Ethernetencapsulation

9.29.18.49.18.3Graceful Routing EngineSwitchover (GRES)

9.39.39.39.39.3In-service software upgrade(ISSU) (Excludes IEEE802.1ag OAM, IEEE802.3ah, and LACPprotocols)

–––––Ingress hierarchical qualityof service (HQoS) shapingand scheduling:

■ Group of virtual LANs(VLANs) level

■ Virtual LAN (VLAN)level

■ Port level

9.29.18.49.18.2IPv4

9.29.18.49.18.2IP multicast

9.29.18.49.18.2IPv6

9.29.18.49.18.2IPv6 multicast

9.29.18.49.18.2IPv6 Neighbor Discovery

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R) ■ 41

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

Page 42: MX Series Ethernet Services Router DPC Guide

Table 2: Protocols and Applications Supported by the MX Series DPCs and Enhanced DPCs (DPC andDPCE-R) (continued)

DPCE-R-20GE-2XGEDPCE-R-40GE-TX

DPCE-R-4XGE-XFP

DPCE-R-40GE-SFPDPCE-R-2XGE-XFP

DPC-R-4XGE-XFP

DPC-R-40GE-SFP

9.29.18.49.18.2IntermediateSystem-to-IntermediateSystem (IS-IS)

9.29.18.49.18.2Layer 2 frame filtering

9.29.18.49.18.2IEEE 802.3ad linkaggregation

9.29.18.49.18.2Link Aggregation ControlProtocol (LACP)

9.29.18.49.18.2Local loopback

9.29.18.49.18.2MAC learning, policing,accounting, and filtering

9.39.39.39.39.3Mobile IP

9.29.18.49.18.4IEEE 802.1s MultipleSpanning Tree Protocol(MSTP) (part of IEEE802.1Q VLANs)

9.29.18.49.18.2Multiple tag protocolidentifiers (TPIDs)

9.29.18.49.18.2Multiprotocol LabelSwitching (MPLS)

9.29.18.49.18.2IEEE 802.3ah OAM

■ Discovery and linkmonitoring

■ Fault signaling anddetection

■ Remote loopback

9.29.19.09.19.0Multitopology Routing(MTR)

9.29.18.49.18.2Open Shortest Path First(OSPF)

9.29.18.49.18.2Packet mirroring

42 ■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

MX Series Ethernet Services Router DPC Guide

Page 43: MX Series Ethernet Services Router DPC Guide

Table 2: Protocols and Applications Supported by the MX Series DPCs and Enhanced DPCs (DPC andDPCE-R) (continued)

DPCE-R-20GE-2XGEDPCE-R-40GE-TX

DPCE-R-4XGE-XFP

DPCE-R-40GE-SFPDPCE-R-2XGE-XFP

DPC-R-4XGE-XFP

DPC-R-40GE-SFP

9.29.18.49.18.2Quality of service (QoS) perport:

■ 8 queues per port

■ Shaping at queue level

■ Scheduling of queuesbased on weightedround-robin (WRR)per priority class

■ Random earlydetection (RED)

■ Weighted randomearly detection(WRED)

9.29.18.49.18.2Quality of service (QoS) pervirtual LAN (VLAN):

■ Accounting, filtering,and policing

■ IEEE 802.1p rewrite

■ Classification

■ Tricolor marking

–––––Quality of service (QoS)queuing per virtual LAN(VLAN)

9.29.18.49.18.4IEEE 802.1w RapidSpanning Tree Protocol(RSTP)

9.29.19.09.19.0Per-VLAN Spanning Tree(PVST)+

9.29.18.49.18.2RSVP

9.29.18.49.18.2Routing InformationProtocol (RIP)

9.29.18.49.18.2SNMP

9.29.18.49.18.4IEEE 802.1D SpanningTree Protocol (STP)

9.49.49.49.49.4Subscriber Management:

9.49.49.49.49.4■ Access Node ControlProtocol (ANCP)

9.29.29.29.29.2■ Dynamic profiles

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R) ■ 43

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

Page 44: MX Series Ethernet Services Router DPC Guide

Table 2: Protocols and Applications Supported by the MX Series DPCs and Enhanced DPCs (DPC andDPCE-R) (continued)

DPCE-R-20GE-2XGEDPCE-R-40GE-TX

DPCE-R-4XGE-XFP

DPCE-R-40GE-SFPDPCE-R-2XGE-XFP

DPC-R-4XGE-XFP

DPC-R-40GE-SFP

9.59.59.59.5–■ Dynamic VLANs

9.39.39.39.39.3■ Enhanced DynamicHost ConfigurationProtocol (DHCP) localserver

9.39.39.39.39.3■ Enhanced DCHP relay

9.29.29.29.29.2■ Firewall filters

9.29.29.29.29.2■ Internet GroupManagement Protocol(IGMP)

9.39.39.39.39.3■ Mobile IP

9.29.29.29.29.2■ QoS

9.49.49.49.49.4■ Subscriber SecurePolicy

9.59.59.59.59.5Two-Way ActiveMeasurement Protocol(TWAMP)

9.29.18.49.18.2IEEE 802.1Q VLANs:

■ VLAN stacking andrewriting

■ Channels defined bytwo stacked VLANtags

■ Flexible VLAN tagging

■ IP service fornonstandard TPIDand stacked VLANtags

9.29.18.49.18.2Virtual private LAN service(VPLS)

9.29.18.49.18.2Virtual private network(VPN)

9.29.18.49.18.2Virtual Router RedundancyProtocol (VRRP) for IPv4

44 ■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

MX Series Ethernet Services Router DPC Guide

Page 45: MX Series Ethernet Services Router DPC Guide

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R) ■ 45

Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs (DPC and DPCE-R)

Page 46: MX Series Ethernet Services Router DPC Guide

Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs(DPCE-X)

Table 3 on page 46 contains the first JUNOS support for protocols and applicationson the MX Series Enhanced Ethernet Services DPCs. A dash indicates that the protocolor application is not supported.

Table 3: Protocols and Applications Supported by the MX Series Enhanced Ethernet Services DPCs (DPCE-X)

DPCE-X-20GE-2XGEDPCE-X-40GE-TX

DPCE-X-4XGE-XFP

DPCE-X-40GE-SFP

Multi-Rate EnhancedEthernet Services DPC

Tri-Rate EnhancedEthernet Services DPC

Enhanced EthernetServices DPC

Name

Protocol or Application

9.49.49.4Access Node Control Protocol (ANCP)

9.29.18.4Accepts traffic destined for GRE tunnelsor DVMRP (IP-in-IP) tunnels

9.29.18.4Bidirectional Forwarding Detectionprotocol (BFD)

9.29.18.4Border Gateway Protocol (BGP)

9.29.18.4BGP/Multiprotocol Label Switching (MPLS)virtual private networks (VPNs)

9.29.18.4Distance Vector Multicast Routing Protocol(DVMRP) and generic routingencapsulation (GRE) support—access sideand server side

9.29.18.4IEEE 802.1ag Ethernet OAM ContinuityCheck protocol

9.29.19.0IEEE 802.1ag Ethernet OAM Linktraceprotocol

9.29.19.1IEEE 802.1ag Ethernet OAM Loopbackprotocol

9.2(Limited filter terms)

9.1(Limited filter terms)

8.4(Limited filter terms)

Firewall filters

9.29.18.4Flexible Ethernet encapsulation

9.29.18.4Graceful Routing Engine Switchover(GRES)

9.29.19.1In-service software upgrade (ISSU)(Excludes IEEE 802.1ag OAM, IEEE802.3ah, and LACP protocols)

46 ■ Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X)

MX Series Ethernet Services Router DPC Guide

Page 47: MX Series Ethernet Services Router DPC Guide

Table 3: Protocols and Applications Supported by the MX Series Enhanced Ethernet Services DPCs(DPCE-X) (continued)

DPCE-X-20GE-2XGEDPCE-X-40GE-TX

DPCE-X-4XGE-XFP

DPCE-X-40GE-SFP

–––Ingress hierarchical quality of service(HQoS) shaping and scheduling:

■ Group of virtual LANs (VLANs) level

■ Virtual LAN (VLAN) level

■ Port level

9.29.18.4Intermediate System-to-IntermediateSystem (IS-IS)

9.2)9.18.4IPv4 (No BGP)

9.29.18.4IP multicast (No BGP)

9.2)9.18.4IPv6 (No BGP)

9.2)9.18.4IPv6 multicast (No BGP)

9.2)9.1)8.4IPv6 Neighbor Discovery (No BGP)

9.29.18.4Layer 2 frame filtering

9.29.18.4IEEE 802.3ad link aggregation

9.29.18.4Link Aggregation Control Protocol (LACP)

9.29.18.4Local loopback

9.29.18.4MAC learning, policing, accounting, andfiltering

9.39.39.3Mobile IP

9.29.18.4IEEE 802.1s Multiple Spanning TreeProtocol (MSTP) (part of IEEE 802.1QVLANs)

9.29.18.4Multiple tag protocol identifiers (TPIDs)

9.29.18.4Multiprotocol Label Switching (MPLS)

9.29.18.4IEEE 802.3ah OAM

■ Discovery and link monitoring

■ Fault signaling and detection

■ Remote loopback

9.29.19.0Multitopology Routing (MTR)

9.29.18.4Open Shortest Path First (OSPF)

Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X) ■ 47

Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X)

Page 48: MX Series Ethernet Services Router DPC Guide

Table 3: Protocols and Applications Supported by the MX Series Enhanced Ethernet Services DPCs(DPCE-X) (continued)

DPCE-X-20GE-2XGEDPCE-X-40GE-TX

DPCE-X-4XGE-XFP

DPCE-X-40GE-SFP

9.29.18.4Packet mirroring

9.29.18.4Quality of service (QoS) per port:

■ 8 queues per port

■ Shaping at queue level

■ Scheduling of queues based onweighted round-robin (WRR) perpriority class

■ Random early detection (RED)

■ Weighted random early detection(WRED)

9.29.18.4Quality of service (QoS) per virtual LAN(VLAN):

■ Accounting, filtering, and policing

■ IEEE 802.1p rewrite

■ Classification

■ Tricolor marking

–––Quality of service (QoS) queuing per virtualLAN (VLAN)

9.29.18.4IEEE 802.1w Rapid Spanning TreeProtocol (RSTP)

9.29.19.0Per-VLAN Spanning Tree (PVST)+

9.29.18.4RSVP

9.29.18.4Routing Information Protocol (RIP)

9.29.18.4SNMP

9.29.18.4IEEE 802.1D Spanning Tree Protocol (STP)

9.49.49.4Subscriber Management:

9.49.49.4■ Access Node Control Protocol (ANCP)

9.29.29.2■ Dynamic profiles

9.59.59.5■ Dynamic VLANs

9.39.39.3■ Enhanced Dynamic HostConfiguration Protocol (DHCP) localserver

48 ■ Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X)

MX Series Ethernet Services Router DPC Guide

Page 49: MX Series Ethernet Services Router DPC Guide

Table 3: Protocols and Applications Supported by the MX Series Enhanced Ethernet Services DPCs(DPCE-X) (continued)

DPCE-X-20GE-2XGEDPCE-X-40GE-TX

DPCE-X-4XGE-XFP

DPCE-X-40GE-SFP

9.39.39.3■ Enhanced DCHP relay

9.29.29.2■ Firewall filters

9.29.29.2■ Internet Group Management Protocol(IGMP)

9.39.39.3■ Mobile IP

9.29.29.2■ QoS

9.49.49.4■ Subscriber Secure Policy

9.59.59.5Two-Way Active Measurement Protocol(TWAMP)

9.29.18.4IEEE 802.1Q VLANs:

■ VLAN stacking and rewriting

■ Channels defined by two stackedVLAN tags

■ Flexible VLAN tagging

■ IP service for nonstandard TPID andstacked VLAN tags

9.29.18.4Virtual private LAN service (VPLS)

9.29.18.4Virtual private network (VPN) (L2 VPNonly)

9.29.18.4Virtual Router Redundancy Protocol(VRRP) for IPv4

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X) ■ 49

Protocols and Applications Supported by MX Series Enhanced Ethernet Services DPCs (DPCE-X)

Page 50: MX Series Ethernet Services Router DPC Guide

Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs(DPCE-R-Q)

Table 4 on page 50 contains the first JUNOS support for protocols and applicationson the MX Series Enhanced Queuing IP Services DPCs. A dash indicates that theprotocol or application is not supported.

Table 4: Protocols and Applications Supported by the MX Series Enhanced Queuing IP Services DPCs(DPCE-R-Q)

DPCE-R-Q-20GE-2XGEDPCE-R-Q-20GE-SFP

DPCE-R-Q-4XGE-XFP

DPCE-R-Q-40GE-SFP

Protocol or Application

9.49.49.4Access Node Control Protocol (ANCP)

9.39.18.5Accepts traffic destined for GRE tunnels orDVMRP (IP-in-IP) tunnels

9.39.18.5Bidirectional Forwarding Detection protocol(BFD)

9.39.18.5Border Gateway Protocol (BGP)

9.39.18.5BGP/Multiprotocol Label Switching (MPLS)virtual private networks (VPNs)

9.39.18.5Distance Vector Multicast Routing Protocol(DVMRP) and generic routing encapsulation(GRE) support—access side and server side

9.39.18.5IEEE 802.1ag Ethernet OAM Continuity Checkprotocol

9.39.19.0IEEE 802.1ag Ethernet OAM Linktrace protocol

9.39.19.1IEEE 802.1ag Ethernet OAM Loopback protocol

9.39.18.5Firewall filters

9.39.18.5Flexible Ethernet encapsulation

9.39.18.5Graceful Routing Engine Switchover (GRES)

9.39.39.3In-service software upgrade (ISSU) (ExcludesIEEE 802.1ag OAM, IEEE 802.3ah, and LACPprotocols)

9.39.19.0Ingress hierarchical quality of service (HQoS)shaping and scheduling:

■ Group of virtual LANs (VLANs) level

■ Virtual LAN (VLAN) level

■ Port level

50 ■ Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q)

MX Series Ethernet Services Router DPC Guide

Page 51: MX Series Ethernet Services Router DPC Guide

Table 4: Protocols and Applications Supported by the MX Series Enhanced Queuing IP Services DPCs(DPCE-R-Q) (continued)

DPCE-R-Q-20GE-2XGEDPCE-R-Q-20GE-SFP

DPCE-R-Q-4XGE-XFP

DPCE-R-Q-40GE-SFP

9.39.18.5Intermediate System-to-Intermediate System(IS-IS)

9.39.18.5IPv4

9.39.18.5IP multicast

9.39.18.5IPv6

9.39.18.5IPv6 multicast

9.39.18.5IPv6 Neighbor Discovery

9.39.18.5Layer 2 frame filtering

9.39.18.5IEEE 802.3ad link aggregation

9.39.18.5Link Aggregation Control Protocol (LACP)

9.39.18.5Local loopback

9.39.18.5MAC learning, policing, accounting, and filtering

9.39.39.3Mobile IP

9.39.18.5IEEE 802.1s Multiple Spanning Tree Protocol(MSTP) (part of IEEE 802.1Q VLANs)

9.39.18.5Multiple tag protocol identifiers (TPIDs)

9.39.18.5Multiprotocol Label Switching (MPLS)

9.39.18.5IEEE 802.3ah OAM

■ Discovery and link monitoring

■ Fault signaling and detection

■ Remote loopback

9.39.19.0Multitopology Routing (MTR)

9.39.18.5Open Shortest Path First (OSPF)

9.39.18.5Packet mirroring

Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q) ■ 51

Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q)

Page 52: MX Series Ethernet Services Router DPC Guide

Table 4: Protocols and Applications Supported by the MX Series Enhanced Queuing IP Services DPCs(DPCE-R-Q) (continued)

DPCE-R-Q-20GE-2XGEDPCE-R-Q-20GE-SFP

DPCE-R-Q-4XGE-XFP

DPCE-R-Q-40GE-SFP

9.39.18.5Quality of service (QoS) per port:

■ 8 queues per port

■ Shaping at port level

■ Scheduling of queues based on weightedround-robin (WRR) per priority class

■ Random early detection (RED)

■ Weighted random early detection (WRED)

9.39.18.5Quality of service (QoS) per virtual LAN (VLAN):

■ Accounting, filtering, and policing

■ IEEE 802.1p rewrite

■ Classification

■ Tricolor marking

■ Shaping at queue and port level

■ Scheduling of queues based on weightedround-robin (WRR) per priority class

■ Random early detection (RED)

■ Weighted random early detection (WRED)

9.39.18.5Quality of service (QoS) queuing per virtual LAN(VLAN)

9.39.18.5IEEE 802.1w Rapid Spanning Tree Protocol(RSTP)

9.39.19.0Per-VLAN Spanning Tree (PVST)+

9.39.18.5RSVP

9.39.18.5Routing Information Protocol (RIP)

9.39.18.5SNMP

9.39.18.5IEEE 802.1D Spanning Tree Protocol (STP)

9.49.49.4Subscriber Management:

9.49.49.4■ Access Node Control Protocol (ANCP)

9.29.29.2■ Dynamic profiles

9.59.59.5■ Dynamic VLANs

9.39.39.3■ Enhanced Dynamic Host ConfigurationProtocol (DHCP) local server

52 ■ Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q)

MX Series Ethernet Services Router DPC Guide

Page 53: MX Series Ethernet Services Router DPC Guide

Table 4: Protocols and Applications Supported by the MX Series Enhanced Queuing IP Services DPCs(DPCE-R-Q) (continued)

DPCE-R-Q-20GE-2XGEDPCE-R-Q-20GE-SFP

DPCE-R-Q-4XGE-XFP

DPCE-R-Q-40GE-SFP

9.39.39.3■ Enhanced DCHP relay

9.29.29.2■ Firewall filters

9.29.29.2■ Internet Group Management Protocol(IGMP)

9.39.39.3■ Mobile IP

9.29.29.2■ QoS

9.49.49.4■ Subscriber Secure Policy

9.59.59.5Two-Way Active Measurement Protocol(TWAMP)

9.39.18.5IEEE 802.1Q VLANs:

■ VLAN stacking and rewriting

■ Channels defined by two stacked VLANtags

■ Flexible VLAN tagging

■ IP service for nonstandard TPID andstacked VLAN tags

9.39.18.5Virtual private LAN service (VPLS)

9.39.18.5Virtual private network (VPN)

9.39.18.5Virtual Router Redundancy Protocol (VRRP) forIPv4

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q) ■ 53

Protocols and Applications Supported by MX Series Enhanced Queuing IP Services DPCs (DPCE-R-Q)

Page 54: MX Series Ethernet Services Router DPC Guide

Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet ServicesDPCs (DPCE-X-Q)

Table 5 on page 54 contains the first JUNOS support for protocols and applicationson the MX Series Enhanced Queuing Ethernet Services DPCs. A dash indicates thatthe protocol or application is not supported.

Table 5: Protocols and Applications Supported by the MX Series Enhanced QueuingEthernet Services DPCs (DPCE-X-Q)

DPCE-X-Q-4XGE-XFP

DPCE-X-Q-40GE-SFP

Protocol or Application

9.4Access Node Control Protocol (ANCP)

8.5Accepts traffic destined for GRE tunnels or DVMRP(IP-in-IP) tunnels

8.5Bidirectional Forwarding Detection protocol (BFD)

8.5Border Gateway Protocol (BGP)

8.5BGP/Multiprotocol Label Switching (MPLS) virtual privatenetworks (VPNs)

8.5Distance Vector Multicast Routing Protocol (DVMRP) andgeneric routing encapsulation (GRE) support—access sideand server side

8.5IEEE 802.1ag Ethernet OAM Continuity Check protocol

9.0IEEE 802.1ag Ethernet OAM Linktrace protocol

9.1IEEE 802.1ag Ethernet OAM Loopback protocol

8.5(Limited filter terms)

Firewall filters

8.5Flexible Ethernet encapsulation

8.5Graceful Routing Engine Switchover (GRES)

9.3In-service software upgrade (ISSU) (Excludes IEEE 802.1agOAM, IEEE 802.3ah, and LACP protocols)

9.0Ingress hierarchical quality of service (HQoS) shapingand scheduling:

■ Group of virtual LANs (VLANs) level

■ Virtual LAN (VLAN) level

■ Port level

8.5Intermediate System-to-Intermediate System (IS-IS)

54 ■ Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q)

MX Series Ethernet Services Router DPC Guide

Page 55: MX Series Ethernet Services Router DPC Guide

Table 5: Protocols and Applications Supported by the MX Series Enhanced QueuingEthernet Services DPCs (DPCE-X-Q) (continued)

DPCE-X-Q-4XGE-XFP

DPCE-X-Q-40GE-SFP

8.5IPv4 (No BGP)

8.5IP multicast (No BGP)

8.5IPv6 (No BGP)

8.5IPv6 multicast (No BGP)

8.5IPv6 Neighbor Discovery (No BGP)

8.5Layer 2 frame filtering

8.5IEEE 802.3ad link aggregation

8.5Link Aggregation Control Protocol (LACP)

8.5Local loopback

8.5MAC learning, policing, accounting, and filtering

9.3Mobile IP

8.5IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) (partof IEEE 802.1Q VLANs)

8.5Multiple tag protocol identifiers (TPIDs)

8.5Multiprotocol Label Switching (MPLS)

8.5IEEE 802.3ah OAM

■ Discovery and link monitoring

■ Fault signaling and detection

■ Remote loopback

9.0Multitopology Routing (MTR)

8.5Open Shortest Path First (OSPF)

8.5Packet mirroring

8.5Quality of service (QoS) per port:

■ 8 queues per port

■ Shaping at port level

■ Scheduling of queues based on weighted round-robin(WRR) per priority class

■ Random early detection (RED)

■ Weighted random early detection (WRED)

Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q) ■ 55

Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q)

Page 56: MX Series Ethernet Services Router DPC Guide

Table 5: Protocols and Applications Supported by the MX Series Enhanced QueuingEthernet Services DPCs (DPCE-X-Q) (continued)

DPCE-X-Q-4XGE-XFP

DPCE-X-Q-40GE-SFP

8.5Quality of service (QoS) per virtual LAN (VLAN):

■ Accounting, filtering, and policing

■ IEEE 802.1p rewrite

■ Classification

■ Tricolor marking

■ Shaping at queue and port level

■ Scheduling of queues based on weighted round-robin(WRR) per priority class

■ Random early detection (RED)

■ Weighted random early detection (WRED)

8.5Quality of service (QoS) queuing per virtual LAN (VLAN)

8.5IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

9.0Per-VLAN Spanning Tree (PVST)+

8.5Remote loopback

8.5RSVP

8.5Routing Information Protocol (RIP)

8.5SNMP

8.5IEEE 802.1D Spanning Tree Protocol (STP)

9.4Subscriber Management:

9.4■ Access Node Control Protocol (ANCP)

9.2■ Dynamic profiles

9.5■ Dynamic VLANs

9.3■ Enhanced Dynamic Host Configuration Protocol(DHCP) local server

9.3■ Enhanced DCHP relay

9.2■ Firewall filters

9.2■ Internet Group Management Protocol (IGMP)

9.3■ Mobile IP

9.2■ QoS

56 ■ Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q)

MX Series Ethernet Services Router DPC Guide

Page 57: MX Series Ethernet Services Router DPC Guide

Table 5: Protocols and Applications Supported by the MX Series Enhanced QueuingEthernet Services DPCs (DPCE-X-Q) (continued)

DPCE-X-Q-4XGE-XFP

DPCE-X-Q-40GE-SFP

9.4■ Subscriber Secure Policy

9.5Two-Way Active Measurement Protocol (TWAMP)

8.5IEEE 802.1Q VLANs:

■ VLAN stacking and rewriting

■ Channels defined by two stacked VLAN tags

■ Flexible VLAN tagging

■ IP service for nonstandard TPID and stacked VLANtags

8.5Virtual private LAN service (VPLS)

8.5(L2 VPN only)

Virtual private network (VPN)

8.5Virtual Router Redundancy Protocol (VRRP) for IPv4

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) on page 58

Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q) ■ 57

Protocols and Applications Supported by MX Series Enhanced Queuing Ethernet Services DPCs (DPCE-X-Q)

Page 58: MX Series Ethernet Services Router DPC Guide

Protocols and Applications Supported by the MX Series MultiServices DPC (MS-DPC)

Table 6 on page 58 contains the first JUNOS support for protocols and applicationson the MX Series MultiServices DPCs. A dash indicates that the protocol or applicationis not supported.

Table 6: Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC)

MS-DPC

Protocol or Application

9.3Accepts traffic destined for GRE tunnels

9.3Active flow monitoring exports cflowd version 5 andversion 8 records

9.3Active flow monitoring exports flow monitoring version9 records, based on RFC 3954

9.4Graceful Routing Engine Switchover (GRES)

9.3GRE dont fragment

9.3GRE Key

9.3GRE reassembly

9.3IP Security (IPSec) encryption

9.3Network Address Translation (NAT) for IP addresses

9.3Port Address Translation (PAT) for port numbers

9.3Real-time Performance Monitoring (RPM)

9.3Stateful firewall with packet inspection: detects SYNattacks, ICMP and UDP floods, and ping-of-death attacks

Tunnel services:

9.3■ GRE unicast tunneling-Supports GRE fragmentation

9.4■ IP-IP unicast tunneling

9.4■ Multicast tunneling

9.4■ Protocol Independent Multicast (PIM) sparse modeunicast tunneling

9.4■ Virtual loopback tunneling (VT)

58 ■ Protocols and Applications Supported by the MX Series MultiServices DPC (MS-DPC)

MX Series Ethernet Services Router DPC Guide

Page 59: MX Series Ethernet Services Router DPC Guide

Table 6: Protocols and Applications Supported by the MX Series MultiServices DPC(MS-DPC) (continued)

MS-DPC

9.5Voice over IP (VoIP) services:

■ Border Gateway Function (BGF) using externalH.248/Ia control

■ Integrated Multi-Service Gateway (IMSG)–SessionBorder Controller

Related Topics ■ DPCs Supported on MX Series Routers on page 4

■ Protocols and Applications Supported by MX Series DPCs and Enhanced DPCs(DPC and DPCE-R) on page 40

■ Protocols and Applications Supported by MX Series Enhanced Ethernet ServicesDPCs (DPCE-X) on page 46

■ Protocols and Applications Supported by MX Series Enhanced Queuing IP ServicesDPCs (DPCE-R-Q) on page 50

■ Protocols and Applications Supported by MX Series Enhanced Queuing EthernetServices DPCs (DPCE-X-Q) on page 54

Protocols and Applications Supported by the MX Series MultiServices DPC (MS-DPC) ■ 59

Protocols and Applications Supported by the MX Series MultiServices DPC (MS-DPC)

Page 60: MX Series Ethernet Services Router DPC Guide

Optical Interface Specifications

■ Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX SeriesRouters) on page 60

■ Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications(MX Series Routers) on page 65

■ 10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications(MX Series Routers) on page 68

Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

The following SFPs are supported on MX Series routers. To determine which SFPsare supported on each DPC, see the “Cables and connectors” section for each DPC.

■ Table 7 on page 60 shows the optical specifications for the 1000Base-EX SFP.

■ Table 8 on page 61 shows the optical specifications for the 100Base-FX SFP.

■ Table 9 on page 61 shows the optical specifications for the 1000Base-LH SFP.

■ Table 10 on page 62 shows the optical specifications for the 1000Base-LX SFP.

■ Table 11 on page 62 shows the optical specifications for the 1000Base-LX10SFP.

■ Table 12 on page 63 shows the optical specifications for the 1000Base-SX SFP.

■ Table 13 on page 63 shows the optical specifications for the 1000Base-T SFP.

■ Table 14 on page 64 shows the optical specifications for the 10/100/1000Base-TSFP.

Table 7: Optical Interface Specifications for the 1000Base-EX SFP

1000Base-EXParameter

SFP-GE40KMTransceiver model number

1000 MbpsRate

Single-modeOptical interface

SFPTransceiver type

9/125 SMF cable:24.85 miles/40 km

Maximum distance

1260 through 1360 nmTransmitter wavelength

–4.5 through 0 dBmAverage launch power

–22.5 through –3 dBmAverage receive power

–3 dBmReceiver saturation

60 ■ Optical Interface Specifications

MX Series Ethernet Services Router DPC Guide

Page 61: MX Series Ethernet Services Router DPC Guide

Table 7: Optical Interface Specifications for the 1000Base-EX SFP (continued)

1000Base-EXParameter

–22.5 dBmReceiver sensitivity

Table 8: Optical Interface Specifications for the 100Base-FX SFP

100Base-FXParameter

SFP-1FE-FXTransceiver model number

100 MbpsRate

MultimodeOptical interface

SFPTransceiver type

62.5/125 MMF cable:6562 ft/2 km

50/125 MMF cable:1640 ft/500 m

Maximum distance

1270 through 1380 nmTransmitter wavelength

–19 through –14 dBmAverage launch power

–31 through –14 dBmAverage receive power

–14 dBmReceiver saturation

–31 dBmReceiver sensitivity

Table 9: Gigabit Ethernet 1000Base-LH SFP Optical Interface Specifications

1000Base-LHParameter

SFP-1GE-LHTransceiver model number

1000 MbpsRate

Single-modeOptical interface

SFPTransceiver type

9/125 SMF cable:43.5 miles/70 km

Maximum distance

1355 through 1580 nmTransmitter wavelength

–3 through +3 dBmAverage launch power

–20 through –3 dBmAverage receive power

Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers) ■ 61

Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

Page 62: MX Series Ethernet Services Router DPC Guide

Table 9: Gigabit Ethernet 1000Base-LH SFP Optical Interface Specifications (continued)

1000Base-LHParameter

–3 dBmReceiver saturation

–20 dBmReceiver sensitivity

Table 10: Gigabit Ethernet 1000Base-LX SFP Optical Interface Specifications

1000Base-LXParameter

SFP-1GE-LXTransceiver model number

1000 MbpsRate

Single-modeOptical interface

SFPTransceiver type

62.5/125 and 50/125 MMF cable:1804.5 ft/550 m

Maximum distance

1270 through 1355 nmTransmitter wavelength

–11.5 through –3 dBmAverage launch power

–19 through –3 dBmAverage receive power

–3 dBmReceiver saturation

–19 dBmReceiver sensitivity

Table 11: Optical Interface Specifications for the 1000Base-LX10 SFP

1000Base-LX10Parameter

SFP-1GE-LXTransceiver model number

1000 MbpsRate

Single-modeOptical interface

SFPTransceiver type

9/125 SMF cable: 6.2 miles/10 kmMaximum distance

1270 through 1355 nmTransmitter wavelength

–11.5 through –3 dBmAverage launch power

–19 through –3 dBmAverage receive power

–3 dBmReceiver saturation

62 ■ Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

MX Series Ethernet Services Router DPC Guide

Page 63: MX Series Ethernet Services Router DPC Guide

Table 11: Optical Interface Specifications for the 1000Base-LX10 SFP (continued)

1000Base-LX10Parameter

–19 dBmReceiver sensitivity

Table 12: Gigabit Ethernet 1000Base-SX SFP Optical Interface Specifications

1000Base-SXParameter

SFP-1GE-SXTransceiver model number

1000 MbpsRate

MultimodeOptical interface

SFPTransceiver type

62.5/125 MMF cable:656 ft/200 m

50/125 MMF cable:1640 ft/500 m

Maximum distance

770 through 860 nmTransmitter wavelength

–9.5 through 0 dBmAverage launch power

–17 through 0 dBmAverage receive power

0 dBmReceiver saturation

–17 dBmReceiver sensitivity

Table 13: Optical Interface Specifications for the 1000Base-T Copper SFP

1000Base-TParameter

SFP-1-GE-TTransceiver model number

1000 MbpsRate

328 ft/100 mDistance

RJ-45Connector type

Four-pair, Category 5 shielded twisted-pairCable

MDI crossoverPinout

Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers) ■ 63

Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

Page 64: MX Series Ethernet Services Router DPC Guide

Table 14: Optical Interface Specifications for the 10/100/1000Base-T Copper SFP

10/100/1000Base-TParameter

SFP-1GE-FE-E-TTransceiver model number

Rate selectable at 10, 100, or 1000 MbpsRate

328 ft/100 mDistance

RJ-45Connector type

Four-pair, Category 5 shielded twisted-pairCable

MDI crossoverPinout

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

64 ■ Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

MX Series Ethernet Services Router DPC Guide

Page 65: MX Series Ethernet Services Router DPC Guide

Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX SeriesRouters)

The following bidirectional SFPs are supported on MX Series routers. To determinewhich SFPs are supported on each DPC, see the “Cables and connectors” section foreach DPC.

■ Table 15 on page 65 shows the optical specifications for 100Base-BX bidirectionalSFPs. 100Base-BX bidirectional interfaces are supported in JUNOS 9.6 and laterand must be used in pairs.

■ Table 16 on page 65, Table 17 on page 66, and Table 18 on page 67 show theoptical specifications for 1000Base-BX bidirectional SFPs. 1000Base-BXbidirectional interfaces are supported in JUNOS 9.0 and later and must be usedin pairs.

Table 15: 100Base-BX Bidirectional SFP Optical Interface Specifications

100Base-BX-D100Base-BX-UParameter

100Base-BX-U100Base-BX-DPairs with

EX-SFP-FE20KT15R13EX-SFP-FE20KT13R15Transceiver model number

100 Mbps100 MbpsRate

Single-modeSingle-modeOptical interface

SFPSFPTransceiver type

100Base-BXIEEE 802.3-2005

100Base-BXIEEE 802.3-2005

Standard

9/125 SMF cable:12.4 miles/20 km

9/125 SMF cable:12.4 miles/20 km

Maximum distance

1480 through 1580 nm1260 through 1360 nmTransmitter wavelength

–14 through –8 dBm–14 through –8 dBmAverage launch power

–45 through –8 dBm–45 through –8 dBmAverage receive power

–8 dBm–8 dBmReceiver saturation

–45 dBm–45 dBmReceiver sensitivity

Table 16: Bidirectional Gigabit Ethernet 1000Base-BX SFP (U 13/14 and D 14/13) Optical InterfaceSpecifications

1000Base-BX10-D 14/131000Base-BX10-U 13/14Parameter

1000Base-BX10-U 13/141000Base-BX10-D 14/13Pairs with

Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers) ■ 65

Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

Page 66: MX Series Ethernet Services Router DPC Guide

Table 16: Bidirectional Gigabit Ethernet 1000Base-BX SFP (U 13/14 and D 14/13) Optical InterfaceSpecifications (continued)

1000Base-BX10-D 14/131000Base-BX10-U 13/14Parameter

SFP-GE10KT14R13SFP-GE10KT13R14Transceiver model number

1000 Mbps1000 MbpsRate

Single-modeSingle-modeOptical interface

SFPSFPTransceiver type

IEEE 802.3-2005IEEE 802.3-2005Standard

9/125 SMF cable:6.2 miles/10 km

9/125 SMF cable:6.2 miles/10 km

Maximum distance

1480 through 1500 nm1260 through 1360 nmTransmitter wavelength

–9 through –3 dBm–9 through –3 dBmAverage launch power

–19.5 through –3 dBm–19.5 through –3 dBmAverage receive power

–3 dBm–3 dBmReceiver saturation

–19.5 dBm–19.5 dBmReceiver sensitivity

Table 17: Bidirectional Gigabit Ethernet 1000Base-BX SFP U 13/15 and D 15/13) Optical Interface Specifications

1000Base-BX10-D 15/131000Base-BX10-U 13/15Parameter

1000Base-BX10-U 13/151000Base-BX10-D 15/13Pairs with

SFP-GE10KT15R13SFP-GE10KT13R15Transceiver model number

1000 Mbps1000 MbpsRate

Single-modeSingle-modeOptical interface

SFPSFPTransceiver type

Multivendor agreementMultivendor agreementStandard

9/125 SMF cable:6.2 miles/10 km

9/125 SMF cable:6.2 miles/10 km

Maximum distance

1530 through 1570 nm1270 through 1360 nmTransmitter wavelength

–9 through –3 dBm–9 through –3 dBmAverage launch power

–20 through –3 dBm–20 through –3 dBmAverage receive power

–3 dBm–3 dBmReceiver saturation

–20 dBm–20 dBmReceiver sensitivity

66 ■ Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

MX Series Ethernet Services Router DPC Guide

Page 67: MX Series Ethernet Services Router DPC Guide

Table 18: Bidirectional Gigabit Ethernet 1000Base-BX SFP (40 U 13/15 and D 15/13) Optical InterfaceSpecifications

1000Base-BX40-D 15/131000Base-BX40-U 13/15Parameter

1000Base-BX40-U 13/151000Base-BX40-D 15/13Pairs with

SFP-GE40KT15R13SFP-GE40KT13R15Transceiver model number

1000 Mbps1000 MbpsRate

Single-modeSingle-modeOptical interface

SFPSFPTransceiver type

Multivendor agreementMultivendor agreementStandard

9/125 SMF cable:24.9 miles/40 km

9/125 SMF cable:24.9 miles/40 km

Maximum distance

1530 through 1570 nm1260 through 1360 nmTransmitter wavelength

–3 through 2 dBm–6.5 through 2 dBmAverage launch power

–23 through –3 dBm–23 through –3 dBmAverage receive power

–3 dBm–3 dBmReceiver saturation

–23 dBm–23 dBmReceiver sensitivity

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers) ■ 67

Bidirectional Small Form-Factor Pluggable (SFP) Optical Interface Specifications (MX Series Routers)

Page 68: MX Series Ethernet Services Router DPC Guide

10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications (MX SeriesRouters)

The following XFPs are supported on MX Series routers. To determine which XFPsare supported on each DPC, see the “Cables and connectors” section for each DPC.

■ Table 19 on page 68 shows the optical specifications for the 10-GBase-E XFP.

■ Table 20 on page 68 shows the optical specifications for the 10-GBase-L XFP.

■ Table 21 on page 69 shows the optical specifications for the 10-GBase-S XFP.

■ Table 22 on page 69 shows the optical specifications for the 10-GBase-Z XFP.

Table 19: 10-GBase-E Intermediate Reach (IR-2) XFP Optical Interface Specifications

10-GBase-EParameter

XFP-10G-E-OC192-IR2Transceiver model number

Single-modeOptical interface

XFPTransceiver type

IEEE 802.3ae—2002Standard

9/125 SMF cable: 24.8 miles/40 km: Distancesgreater than 30 km are considered to beengineered links.

Maximum distance

1530 through 1565 nmTransmitter wavelength

–4.7 through +4 dBmAverage launch power

–15.8 through –1.0 dBmAverage receive power

–1.0 dBmReceiver saturation

–15.8 dBmReceiver sensitivity

Table 20: 10-GBase-L Short Reach (SR-1) XFP Optical Interface Specifications

10-GBase-LParameter

XFP-10G-L-OC192-SR1Transceiver model number

Single-modeOptical interface

XFPTransceiver type

IEEE 802.3ae—2002Standard

9/125 SMF cable: 6.2 miles/10 kmMaximum distance

68 ■ 10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications (MX Series Routers)

MX Series Ethernet Services Router DPC Guide

Page 69: MX Series Ethernet Services Router DPC Guide

Table 20: 10-GBase-L Short Reach (SR-1) XFP Optical InterfaceSpecifications (continued)

10-GBase-LParameter

1260 through 1355 nmTransmitter wavelength

–8.2 through 0.5 dBmAverage launch power

–14.4 through 0.5 dBmAverage receive power

0.5 dBmReceiver saturation

–14.4 dBmReceiver sensitivity

Table 21: 10-GBase-S Very Short Reach (VSR) XFP Optical Interface Specifications

10-GBase-SParameter

XFP-10G-STransceiver model number

MultimodeOptical interface

XFPTransceiver type

IEEE 802.3ae—2002Standard

50/125 MMF cable, 2000 MHz-km: 984 feet/300 m

50/125 MMF cable, 500 MHz-km: 269 feet/82 m

50/125 MMF cable, 400 MHz-km: 217 feet/66 m

62.5/125 MMF cable, 200 MHz-km: 108 feet/33 m

62.5/125 MMF cable, 160 MHz-km: 85 feet/26 m

Maximum distance

840 through 860 nmTransmitter wavelength

–4.5 through –1.0 dBmAverage launch power

–9.9 through –1.0 dBmAverage receive power

–1.0 dBmReceiver saturation

–9.9 dBmReceiver sensitivity

Table 22: 10-GBase-Z Long Reach (LR-2) XFP Optical Interface Specifications

10-GBase-ZParameter

XFP-10G-Z-OC192-LR2Transceiver model number

Single-modeOptical interface

10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications (MX Series Routers) ■ 69

10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications (MX Series Routers)

Page 70: MX Series Ethernet Services Router DPC Guide

Table 22: 10-GBase-Z Long Reach (LR-2) XFP Optical InterfaceSpecifications (continued)

10-GBase-ZParameter

XFPTransceiver type

Multivendor agreementStandard

9/125 SMF cable: 49.6 miles/80 kmMaximum distance

1530 through 1565 nmTransmitter wavelength

0 through +4 dBmAverage launch power

–24.0 through –7.0 dBmAverage receive power

–7 dBmReceiver saturation

–24 dBmReceiver sensitivity

Related Topics MX Series DPC Overview on page 3■

■ DPCs Supported on MX Series Routers on page 4

70 ■ 10-Gigabit Small Form-Factor Pluggable (XFP) Optical Interface Specifications (MX Series Routers)

MX Series Ethernet Services Router DPC Guide

Page 71: MX Series Ethernet Services Router DPC Guide

JUNOS Documentation and Release Notes

For a list of related JUNOS documentation, seehttp://www.juniper.net/techpubs/software/junos/.

If the information in the latest release notes differs from the information in thedocumentation, follow the JUNOS Software Release Notes.

To obtain the most current version of all Juniper Networks® technical documentation,see the product documentation page on the Juniper Networks website athttp://www.juniper.net/techpubs/.

Requesting Technical Support

Technical product support is available through the Juniper Networks TechnicalAssistance Center (JTAC). If you are a customer with an active J-Care or JNASC supportcontract, or are covered under warranty, and need post-sales technical support, youcan access our tools and resources online or open a case with JTAC.

■ JTAC policies—For a complete understanding of our JTAC procedures and policies,review the JTAC User Guide located athttp://www.juniper.net/customers/support/downloads/710059.pdf .

■ Product warranties—For product warranty information, visithttp://www.juniper.net/support/warranty/ .

■ JTAC hours of operation—The JTAC centers have resources available 24 hours aday, 7 days a week, 365 days a year.

Self-Help Online Tools and Resources

For quick and easy problem resolution, Juniper Networks has designed an onlineself-service portal called the Customer Support Center (CSC) that provides you withthe following features:

■ Find CSC offerings: http://www.juniper.net/customers/support/

■ Search for known bugs: http://www2.juniper.net/kb/

■ Find product documentation: http://www.juniper.net/techpubs/

■ Find solutions and answer questions using our Knowledge Base:http://kb.juniper.net/

■ Download the latest versions of software and review release notes:http://www.juniper.net/customers/csc/software/

■ Search technical bulletins for relevant hardware and software notifications:https://www.juniper.net/alerts/

■ Join and participate in the Juniper Networks Community Forum:http://www.juniper.net/company/communities/

■ Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/

JUNOS Documentation and Release Notes ■ 71

JUNOS Documentation and Release Notes

Page 72: MX Series Ethernet Services Router DPC Guide

To verify service entitlement by product serial number, use our Serial NumberEntitlement (SNE) Tool located at https://tools.juniper.net/SerialNumberEntitlementSearch/.

Opening a Case with JTAC

You can open a case with JTAC on the Web or by telephone.

■ Use the Case Management tool in the CSC at http://www.juniper.net/cm/ .

■ Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

For international or direct-dial options in countries without toll-free numbers, seehttp://www.juniper.net/support/requesting support.html

Revision History

July 2009—Organized optical interfaces into topics. Corrected information about the1000Base-EX SFP.

10 April 2009—530-024404-01. Revision 5. Added new features supported in JUNOSrelease 9.5. Added Subscriber Management features.

26 January 2009—530-024404-01. Revision 4. Added 10/100/1000Base-T SFPinterface for Multi-Rate DPCs. Added new features supported in JUNOS release 9.4.

17 October 2008—530-024404-01. Revision 3. Added new MultiServices andEnhanced Queuing Multi-Rate DPCs. Added 100Base-FX SFP optical interface forMulti-Rate DPCs.

28 July 2008—530-024404-01. Revision 2. Added new Multi-Rate DPCs.

18 April 2008—530-024404-01. Revision 1. Added new Enhanced Queuing EthernetServices DPCs and Tri-Rate DPCs.

1 February 2008—530-022471-01. Revision 2. Added 1000Base-BX SFP opticalinterfaces. Added new software features for JUNOS 9.0 Release.

12 October 2007—530-022471-01. Revision 1. Added Enhanced Queuing EthernetServices DPCs.

7 September 2007—530-021324-02. Revision 1. Corrected average launch powerfor the 10-GBase-L optical interface.

29 June 2007—530-021324-01. Revision 1. Added DPCE-R-40GE-SFP,DPCE-X-40GE-SFP, DPCE-R-4XGE-XFP, and DPCE-X-4XGE-XFP.

6 April 2007—530-017886-02. Revision 1. Corrected the DPC model numbers.

12 March 2007—530-017886-01. Revision 1.

72 ■ Requesting Technical Support

MX Series Ethernet Services Router DPC Guide

Page 73: MX Series Ethernet Services Router DPC Guide

Copyright © 2009, Juniper Networks, Inc. All rights reserved.

Juniper Networks, the Juniper Networks logo, JUNOS, NetScreen, ScreenOS, and Steel-Belted Radius are registered trademarks of Juniper Networks, Inc. inthe United States and other countries. JUNOSe is a trademark of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, orregistered service marks are the property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, orotherwise revise this publication without notice.

Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensedto Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347,6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

Requesting Technical Support ■ 73

Requesting Technical Support