lug botls & locks choosing the correct lug bolt

S

FLOATINGSEAT

SOLIDSEAT

END OF SHANK

PROJECTEDINTERSECTION

INTERSECTION

SHANK

CONE SEAT

S

FLOATINGSEAT SOLID

SEAT

END OF SHANK

PROJECTEDINTERSECTION

INTERSECTION

SHANK

RADIUS SEAT

FLOATING SEAT CONE DIAGRAM

FLOATING SEAT RADIUS DIAGRAM

SOLID SEAT CONE DIAGRAM

SOLID SEAT RADIUS DIAGRAM

WARNING: Lug Bolts are critical wheel fasteners. Read the following guide-lines to ensure that you choose the correct lug bolt. Failure to comply with guidelines & warnings could cause an unsafe condition and result in serious injury or death. Do not use: a bolt with a different seat style (cone, radius, flat); or a bolt shorter or longer than the lug bolt specified for your wheel.

If you are unsure of which part number to use or have installation questions, contact your local McGard installer or McGard at 800-669-6887.

Choosing The Correct Lug BoltIn many cases McGard lug bolts are designed to be a

direct replacement for O.E.M. lug bolts. On the following pages you will find O.E.M. lug bolt part numbers that cross reference to McGard part numbers. If you can identify your O.E.M. part number then you can easily identify the proper McGard part.

If you can’t identify your O.E.M. lug bolts or have aftermarket lug bolts you will have to check for the following: correct thread size; cone or radius style seat-ing surface; the shank length is not too short or too long. Refer to this diagram for information on cor-rectly measuring your lug bolt.

Shank Length Verification

For Solid Seat (1-piece) bolt designs, the shank length S is measured from the end of the shank to the INTERSECTION (narrowest point of the seat). See the solid seat diagrams captioned in blue.

For Floating Seat (2-piece) bolt designs, the shank length S is measured from the end of the shank to the PROJECTED INTERSECTION (red dotted line). See the floating seat diagrams captioned in green.

The PROJECTED INTERSECTION on a floating seat (2-piece) bolt corresponds with the INTERSECTION on a solid seat (1-piece) bolt.

Lock bolt applications/dimensions should not be used to cross reference/determine lug bolt applications.

DISCLAIMER: The information on the following pages is believed to be accurate, but is intended for reference purposes only, and not meant to be an application guide. You must test fit lug bolts on each wheel to ensure proper fit. It is your responsibility to double check that the correct bolt is used and correctly installed. McGard is not responsible for use of an incorrect bolt or incorrect installation.

The ConvenientWay to Order Wheel Locks and Lug Bolts.

O.E.M. design & safety PLUS Beauty, Style, Precision & Durability!

The floating seat (2-piece) design provides optimum safety and per-

formance. This protects against galling and helps prevent seized/

difficult to remove bolts. Precision manufacturing exceeds

O.E.M. requirements.

Bright chrome & beautiful black finish enhances the look of any

wheel. The black & chrome plating is guaranteed for life not to chip,

peel or rust.

Available in Wheel Installation Kits that include wheel locks

and bulk boxes of 50.

CHROME PLATINGThe best in the industry. Our process includes several layers of nickel and

one layer of microporous chrome. The layers of nickel are for corrosion

resistance, luster and interaction with the microporous chrome layer to

disperse nature’s corrosive action (rust).

PRECISION COATED THREADSCore integrity provides the highest strength in the industry. McGard lug bolts exceed the highest O.E.M. proof load and tensile load standards. The unique process of applying multiple pro-prietary coatings helps prevent seized or difficult to remove lug bolts.

PRECISE BEARING SURFACEMcGard’s floating seat design

allows for precision concentric-ity of the bearing surface to the

pitch diameter. This ensures even distribution of the clamp load and

uniform seating of the lug bolt to the wheel hub assembly.

IDENTIFICATIONWe roll mark our name into the

surface of every lug bolt. This is your assurance that you are getting genuine McGard quality and safety.

THROUGH-HARDENED STEELEvery lug bolt is through-hardened and tempered, reaching the depth of hardness needed for its unsurpassed level of safety (unlike case hardening which is only a surface treatment).

STEELOur stringent standards ensure the structural integrity of each and every McGard lug bolt.

FLOATING SEATThe floating seat design provides pre-cision control of the torque tension characteristics between the fastener and wheel hub assembly.

Lug Bolts & Locks

CHOOSING THE CORRECTLug Bolt

California Residents: WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov.

✔When choosing the

proper lug bolt check for:

➊ Correct thread size.

➋ Cone or Radius style

seating surface.

➌Shank length is not

too short or too long.

During wheel instal-lation, bolt shank length must be

checked for proper fit. Too short of a shank will result in lack of engagement and an

unsafe condition. Too long of a shank can extend beyond the

hub assembly and pos-sibly cause damage to other vehicle parts.

Lock bolt applica-tions/dimensions

should not be used to cross reference/determine lug bolt

applications.

✔When choosing the

proper lug bolt check for:

➊ Correct thread size.

➋ Cone or Radius style

seating surface.

➌Shank length is not

too short or too long.

During wheel instal-lation, bolt shank length must be

checked for proper fit. Too short of a shank will result in lack of engagement and an

unsafe condition. Too long of a shank can extend beyond the

hub assembly and pos-sibly cause damage to other vehicle parts.

Lock bolt applica-tions/dimensions

should not be used to cross reference/determine lug bolt

applications.

Y

FLOATINGSEAT

MCGARDSHANK LENGTH

Y

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

AFTERMARKET

MCGARDSHANK LENGTH

FLOATINGSEAT

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

FLOATINGSEAT

MCGARDSHANK LENGTH

For BMW/MINI M12x1.5 applications using BMW/MINI bolt p/n: 36-13-6-781-150

INSTALLATION KIT BOX/50 MCGARD MCGARD THREAD SIZE 5 LUG PART NO. HEX SIZE OVERALL LENGTH

M12x1.5 67179 69779 17mm 54.1mm 25.5mm M12x1.5 black 67179BK 69779BK 2.13” 1.00”

For Chrysler, Dodge & Jeep M12x1.25 bolt applications on a 60º cone seat wheel Hex does not match O.E.M. lug wrench.



For VOLVO M14x1.5 applications using VOLVO bolt p/n’s: 31362432, 31373474, 31323735, 31439230, 31362432, 31423735Hex does not match O.E.M. lug wrench.



For BMW/MINI M14x1.25 applications using BMW/MINI bolt p/n’s: 36-13-6-781-151, 36-13-6-890-324



For FIAT 500 M12x1.25 applications using FIAT bolt p/n: 65 10 68 5 AA



Aftermarket Replacement



60º Cone seat Installation Kits include lug bolts, 4 wheel lock bolts, key tool, key tool storage pouch and ID card. Chrome unless noted otherwise. Contact your local dealership with your VIN# to find out the O.E.M. lug bolt part number that fits your vehicle.

AUDI & VOLKSWAGEN M14x1.5 (13mm) radius seat applications using AUDI/VOLKSWAGEN bolt p/n’s: WHT-002-437, WHT-002-438, WHT-001-812, 8RO-601-295

INSTALLATION KIT BOX/50 MCGARD SEAT MCGARD THREAD SIZE 5 LUG PART NO. HEX SIZE RADIUS OVERALL LENGTH

M14x1.5 68018 69818 17mm 13mm 51.4mm 26.3mm M14x1.5 black 68018BK 69818BK 2.02” 1.04”

PORSCHE M14x1.5 (14mm) radius seat applications using PORSCHE bolt p/n’s: 997-361-203-01, WHT-006-978Hex does not match O.E.M. lug wrench.

INSTALLATION KIT BOX/50 MCGARD SEAT THREAD SIZE 5 LUG PART NO. HEX SIZE RADIUS OVERALL LENGTH


PORSCHE, AUDI & VOLKSWAGEN M14x1.5 (14mm) radius seat applications using bolt p/n’s: WHT-001-693, WHT-002-529, WHT-001-964-A, WHT-004-676, WHT-004-676-AHex does not match O.E.M. lug wrench.

INSTALLATION KIT BOX/50 MCGARD SEAT THREAD SIZE 5 LUG PART NO. HEX SIZE RADIUS OVERALL LENGTH


INFINITI, MERCEDES-BENZ M14x1.5 (14mm) radius seat applications using bolt p/n’s: 000-990-49-07, 000-990-51-07 (fluted hex), 000-990-83-07, 005-990-25-00,001-990-06-07

INSTALLATION KIT BOX/50 MCGARD SEAT MCGARD THREAD SIZE 5 LUG PART NO. HEX SIZE RADIUS OVERALL LENGTH


Radius seat Installation Kits include lug bolts, 4 wheel lock bolts, key tool, key tool stor-age pouch and ID card. Chrome unless noted otherwise. Contact your local dealership with your VIN# to find out the O.E.M. lug bolt part number that fits your vehicle.

Due to the superior 2-piece design & construction of McGard lug bolts, the

shank length measurement is measured from the end of the shank to the

PROJECTED INTERSECTION (red dotted line). See pages 98-99 for information on choosing the correct lug bolt and

verifying shank length. Bolt diagrams are shown at actual size.

Radius Seat Lug Bolts

Installation Kits and Bulk Boxes

Cone Seat Lug Bolt

Installation Kits & Bulk Boxes


ILLUSTRATION #1

ILLUSTRATION #2

Misapplication: insufficient thread engagement into the hub assembly.

Possible misapplication: shank has passed through hub assembly, which could result in vehicle damage.

Vehicles usinglug bolts requireeither a cone seator radius seat.The lock musthave the sametype of seat andsize to properlyfit the wheel.

Check the chartsprovided to becertain the threadsize, seat type andsize, and shanklength are correctfor the wheelbeing used. Matchthe chart informa-tion with a lugbolt being used onthe wheel.

For matching lug boltssee pages 100-101.

SHAN

KLE

NGTH

SHAN

KLE

NGTH

SHAN

KLE

NGTH

● This symboldenotes part

numbers that areavailable in

WheelInstallation

KitsSimplify your ordering,

See pages 100-101.

60º Cone Seat Tuner Lock BoltsA no-compromise design engineered to fit small diameter recesses in Tuner style wheels.

THREAD SIZE OVERALL LENGTH SHANK LENGTH KEY HEX SIZE PART NO.

M12x1.5 51.4mm 2.02” 22.4mm 0.88” 17mm 27192M12x1.5 56.9mm 2.24” 29.6mm 1.16” 17mm 27191M14x1.5 50.3mm 1.98” 24.0mm 0.95” 17mm 27200M14x1.5 55.8mm 2.20” 28.6mm 1.13” 17mm 27201

60º Cone Seat Lock BoltsTHREAD SIZE OVERALL LENGTH SHANK LENGTH KEY HEX SIZE PART NO.

M12x1.25 47.1mm 1.86” 22.0mm 0.87” 17mm 27216 ●M12x1.25 black 47.1mm 1.86” 22.0mm 0.87” 17mm 27316 ●M12x1.25 54.5mm 2.15” 29.1mm 1.15” 19mm & 3/4” 27169M12x1.25 54.1mm 2.13” 25.6mm 1.01” 19mm & 3/4” 27261 ●M12x1.25 black 54.1mm 2.13” 25.6mm 1.01” 19mm & 3/4” 27361 ●M12x1.5 43.4mm 1.71” 18.2mm 0.72” 21mm & 13/16” 27100M12x1.5 47.4mm 1.86” 22.2mm 0.87” 17mm 27204M12x1.5 50.7mm 2.00” 25.5mm 1.00” 17mm 27179 ●M12x1.5 black 50.7mm 2.00” 25.5mm 1.00” 17mm 27178 ●M12x1.5 56.9mm 2.24” 31.7mm 1.25” 17mm 27015M12x1.5 61.5mm 2.42” 36.3mm 1.43” 21mm & 13/16” 27111M12x1.5 65.6mm 2.58” 40.5mm 1.59” 17mm 27013M12x1.5 72.7mm 2.86” 49.2mm 1.94” 17mm 27014M12x1.75 54.2mm 2.13” 28.9mm 1.14” 19mm & 3/4” 27186M14x1.25 51.7mm 2.04” 27.3mm 1.07” 17mm 27226 ●M14x1.25 black 51.7mm 2.04” 27.3mm 1.07” 17mm 27326 ●M14x1.5 51.4mm 2.02” 27.5mm 1.08” 17mm 27222M14x1.5 52.9mm 2.08” 29.0mm 1.14” 17mm 27181M14x1.5 54.9mm 2.16” 31.0mm 1.22” 19mm & 3/4” 27000M14x1.5 54.9mm 2.16” 31.0mm 1.22” 17mm 27205 ●M14x1.5 black 54.9mm 2.16” 31.0mm 1.22” 17mm 27305 ●

Radius Seat Lock BoltsTHREAD SIZE SEAT RADIUS OVERALL LENGTH SHANK LENGTH KEY HEX SIZE PART NO.

M12x1.5 12mm 41.2mm 1.62” 20.6mm 0.81” 17mm 28176M12x1.5 13mm 44.0mm 1.73” 23.3mm 0.92” 17mm 28175M12x1.5 12mm 48.6mm 1.91” 27.9mm 1.10” 17mm 28172M12x1.5 12mm 63.0mm 2.48” 39.9mm 1.57” 17mm 28023M14x1.5 14mm 48.9mm 1.93” 27.0mm 1.06” 17mm 28174 ●M14x1.5 black 14mm 48.9mm 1.93” 27.0mm 1.06” 17mm 28374 ●M14x1.5 13mm 48.0mm 1.89” 26.7mm 1.05” 17mm 28018 ●M14x1.5 black 13mm 48.0mm 1.89” 26.7mm 1.05” 17mm 28318 ●M14x1.5 14mm 61.5mm 2.42” 28.2mm 1.11” 17mm 28020 ●M14x1.5 black 14mm 61.5mm 2.42” 28.2mm 1.11” 17mm 28320 ●M14x1.5 14mm 63.3mm 2.49” 35.4mm 1.39” 19mm & 3/4” 28032 ●M14x1.5 black 14mm 63.3mm 2.49” 35.4mm 1.39” 19mm & 3/4” 28332 ●M14x1.5 14mm 66.9mm 2.63” 45.0mm 1.77” 17mm 28017 M14x1.5 black 14mm 66.9mm 2.63” 45.0mm 1.77” 17mm 28317

WARNINGS:Do not use a lock with a different seat style orsize than the lug bolt being used on the wheel.Do not use a lock shorter or longer than thelug bolt being used on the wheel.Do not use more than one lock bolt per wheel.

Verification for Cone & Radius Seat Lock Bolt or Lug Bolt:

Warnings: When installing wheel lock bolts and lug bolts, verify that it is the correct thread size, seating surface (cone seat, radius seat) and style as recommended by the wheel manufacturer. Minimum thread engagement into hub assembly must be 5½ complete 360º revolutions of bolt (5½ full bolt rotations).

WARNING: Lug Bolts are critical wheel fasteners. Read the following guide-lines to ensure that you choose and install the correct lug bolt. Failure to comply with guidelines & warnings could cause an unsafe condition and result in serious injury or death.

1 Remove one lug bolt from both a front wheel and rear wheel.

2 Visually verify that the seating sur-face of your current fasteners match the McGard fasteners. Verify that the thread size and shank measurement of your current fasteners match the McGard fasteners. See pages 98-101 for details.

3 Install one McGard lug or lock bolt on each wheel from step one. Tighten to normal installation torque. Minimum thread engagement into hub assembly

must be 5½ complete 360º revolu-tions. Too short of a shank will result in lack of engagement and an unsafe condition (see illustration #1). Too long of a shank can extend beyond the hub assembly and possibly cause dam-age to other vehicle parts (see illus-tration #2).

4 Upon verification of proper applica-tion, complete installation per McGard’s installation instructions on page 108.

Note: If your spare tire is a steel wheel and your road wheels are aluminum, you must also verify the application for your spare tire/wheel. If you do not wish to verify the application now, you should keep enough of your original fasteners in your vehicle for use with the spare tire/wheel.

TYPICALLOCK BOLT

60º CONE

TYPICALLOCK BOLT

RADIUS SEAT

TYPICALLUG BOLT

60º CONE

TYPICALLUG BOLT

RADIUS SEAT

CONE & RADIUS SEATLock Bolts 103

www.mcgard.comBOLT APPLICATIONVerification


lug botls & locks choosing the correct lug bolt

Documents