i-tec i30h-i60h 2-stage compressor high …...form no s3451-918 supersedess3451-818 page 4 of 20 hot...

20
Form No S3451-918 Supersedes S3451-818 Page 1 of 20 The Bard I-TEC Indoor Heat Pump system is designed for classrooms and other similar applications demanding high efficiency and the lowest possible sound levels that are practical and achievable, and also accommodates the over-the-window sill requirement for many replacement projects on older school buildings. The I-TEC Series meets that challenge with many innovative design features resulting in a highly refined appearance while at the same time improving on the very important maintenance and serviceability features needed by the facilities maintenance and service staffs. I-TEC ® I30H-I60H 2-Stage Compressor High Efficiency Air Source Heat Pumps Four Ventilation Options: Both ERV and CRV have ECM motors, filter system, and positive shut-off. Energy Recovery Ventilator (ERV) is designed for both modulating or fixed supply and exhaust airflow operation depending upon environmental controls used, and has positive shutoff on intake and exhaust sides when unoccupied. Modulating mode requires CO 2 controller, has intake rate that is higher than exhaust, and has optional minimum CFM to address building IAQ requirements. The system modulates to maintain selected maximum CO 2 level. Fixed mode can be used with thermostat or DDC that has a dedicated Occupied output that is ON during Occupied and OFF during Unoccupied. Intake and exhaust rates can be independently adjusted. Commercial Room Ventilator (CRV Option M) is a fan powered ventilation package to manage intake & exhaust air at fixed rates but without energy recovery capability. The rates are: 300-375-450-525 CFM, are independently selectable & has positive shutoff on intake and exhaust sides when unoccupied. Requires control system that has a dedicated ventilation control output to be ON during Occupied and OFF during Unoccupied. CO2 controller with ON/OFF output relay can be used. Factory setting is 375 CFM balanced to meet pressurization requirements of ASHRAE. Commercial Room Ventilator (CRV Option N) is same as CRV Option M and also has a free-cooling economizer mode that can provide up to 525 CFM when the outdoor ambient temperature is below the set point of the outdoor thermostat. I-TEC Optional Features & Accessories I-TEC Standard Features Commercial Room Ventilator (CRV Option Q) is modulating design that requires 0-10Vdc control signal from CO 2 controller. Other Options: Dehumidification (hot gas reheat) models Low Ampacity Models available Hot water coil packages, both Duct-Free and Ducted versions available. Accessories: See Page 9 & 10. Units designed to be flush to a smooth interior wall and not require trim kits by use of adjustable wall sleeves; Trim Kits available where required Low sound levels are achieved by numerous system design innovations including special acoustical insulation Installation flexibility. Can be installed in corner applications with one side against a wall. Condensate overflow detection system with diagnostics monitors equipment and shuts down compressor to prevent condensate overflow. Freezestat on indoor coil safeguards against indoor coil freeze up by shutting down the compressor. Double wall construction, 20-ga. exterior skin, no visible fasteners Non fiberglass insulation Hinged, lockable, removable doors Removable sides and modularized construction for transporting through standard doors or in elevators allows installation on second and third floor Suitable for any floor installations Can be installed in left or right corners with no modifications Non-corrosive drainpans with no standing water 2-Stage scroll compressors with discharge muffler, double floating isolation mounting system, and sound muffling cover R-410A Green Refrigerant Heating and cooling thermostatic expansion valves Extra large full width control panel for easy access to all controls Circuit Breakers on 230V models, and Toggle Disconnect on 460V Evaporator coils constructed with hydrophilic fin stock with the following advantages: Acrylic coating Wettable surface with low contact angle – no bead-up condensate, lower wet-coil air-side pressure drop, improved draining & lower re-entrainment of moisture back into the air stream in continuous blower operating modes Antimicrobial properties provide microbial resistance to fungicidal growth Resistant to Mold and Mildew, ASTM D3273 – no growth Seals fin surface against aluminum oxide formation 24VAC 75VA control transformer with circuit breaker 24VAC low-voltage terminal strip for thermostat or DDC control ECM indoor and outdoor motors Modulating outdoor fan motor and low ambient control Modulating indoor fan motor for constant CFM in different operating modes up to 0.50" ESP High and Low Pressure switches with lockout circuit Electronic heat pump control board with diagnostics Liquid line filter/drier Readily accessible service ports located behind locking hinged doors Pleated 2" MERV 8 filter Designed for over-the-window sill wall penetration and has 3" vertical adjustment for wall sleeve attachment Cooling Capacities: 22,800 to 54,000 Btuh Heating Capacities: 19,800 to 54,000 Btuh MIS-3741 MIS-3742 ERV CRV

Upload: others

Post on 09-Jul-2020

4 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 1 of 20

The Bard I-TEC Indoor Heat Pump system is designed for classrooms and other similar applications demanding high efficiency and the lowest possible sound levels that are practical and achievable, and also accommodates the over-the-window sill requirement for many replacement projects on older school buildings. The I-TEC Series meets that challenge with many innovative design features resulting in a highly refined appearance while at the same time improving on the very important maintenance and serviceability features needed by the facilities maintenance and service staffs.

I-TEC® I30H-I60H 2-Stage CompressorHigh Efficiency Air Source Heat Pumps

Four Ventilation Options:Both ERV and CRV have ECM motors, filter system, and positive shut-off.Energy Recovery Ventilator (ERV) is designed for both modulating or fixed supply and exhaust airflow operation depending upon environmental controls used, and has positive shutoff on intake and exhaust sides when unoccupied.• Modulating mode requires CO2 controller, has intake rate that is higher than exhaust, and has optional minimum CFM to address building IAQ requirements. The system modulates to maintain selected maximum CO2 level.• Fixed mode can be used with thermostat or DDC that has a dedicated Occupied output that is ON during Occupied and OFF during Unoccupied. Intake and exhaust rates can be independently adjusted.Commercial Room Ventilator (CRV Option M) is a fan powered ventilation package to manage intake & exhaust air at fixed rates but without energy recovery capability.• The rates are: 300-375-450-525 CFM, are independently selectable & has positive shutoff on intake and exhaust sides when unoccupied.• Requires control system that has a dedicated ventilation control output to be ON during Occupied and OFF during Unoccupied. CO2 controller with ON/OFF output relay can be used.• Factory setting is 375 CFM balanced to meet pressurization requirements of ASHRAE.Commercial Room Ventilator (CRV Option N) is same as CRV Option M and also has a free-cooling economizer mode that can provide up to 525 CFM when the outdoor ambient temperature is below the set point of the outdoor thermostat.

I-TEC Optional Features & Accessories

I-TEC Standard Features

Commercial Room Ventilator (CRV Option Q) is modulating design that requires 0-10Vdc control signal from CO2 controller.

Other Options: • Dehumidification (hot gas reheat) models • Low Ampacity Models available • Hot water coil packages, both Duct-Free and Ducted versions available.

Accessories: See Page 9 & 10.

• Units designed to be flush to a smooth interior wall and not require trim kits by use of adjustable wall sleeves; Trim Kits available where required • Low sound levels are achieved by numerous system design innovations including special acoustical insulation • Installation flexibility. Can be installed in corner applications with one side against a wall. • Condensate overflow detection system with diagnostics monitors equipment and shuts down compressor to prevent condensate overflow. • Freezestat on indoor coil safeguards against indoor coil freeze up by shutting down the compressor.

• Double wall construction, 20-ga. exterior skin, no visible fasteners • Non fiberglass insulation • Hinged, lockable, removable doors • Removable sides and modularized construction for transporting through standard doors or in elevators allows installation on second and third floor • Suitable for any floor installations • Can be installed in left or right corners with no modifications • Non-corrosive drainpans with no standing water • 2-Stage scroll compressors with discharge muffler, double floating isolation mounting system, and sound muffling cover • R-410A Green Refrigerant • Heating and cooling thermostatic expansion valves • Extra large full width control panel for easy access to all controls • Circuit Breakers on 230V models, and Toggle Disconnect on 460V • Evaporator coils constructed with hydrophilic fin stock with the following advantages: Acrylic coating Wettable surface with low contact angle – no bead-up condensate, lower wet-coil air-side pressure drop, improved draining & lower re-entrainment of moisture back into the air stream in continuous blower operating modes Antimicrobial properties provide microbial resistance to fungicidal growth Resistant to Mold and Mildew, ASTM D3273 – no growth Seals fin surface against aluminum oxide formation • 24VAC 75VA control transformer with circuit breaker • 24VAC low-voltage terminal strip for thermostat or DDC control • ECM indoor and outdoor motors • Modulating outdoor fan motor and low ambient control • Modulating indoor fan motor for constant CFM in different operating modes up to 0.50" ESP • High and Low Pressure switches with lockout circuit • Electronic heat pump control board with diagnostics • Liquid line filter/drier • Readily accessible service ports located behind locking hinged doors • Pleated 2" MERV 8 filter • Designed for over-the-window sill wall penetration and has 3" vertical adjustment for wall sleeve attachment

Cooling Capacities: 22,800 to 54,000 Btuh Heating Capacities: 19,800 to 54,000 Btuh

MIS-3741

MIS-3742

ERV

CRV

Page 2: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 2 of 20

Specifications - 4 and 5 Ton

Specifications - 2½ through 3½ Ton

MODELS I48H1-A I48H1-B I48H1-C I60H1-A I60H1-B I60H1-C

ELECTRICAL RATING--60 HZ 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3

Operating Voltage Range 197-253 414-506 197-253 414-506

COMPRESSOR

Volts 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3

Rated Load Amps (230/208) 15.6/17.5 10.4/11.6 5.4 22/23.4 13.4/14.3 6.3

Branch Circuit Selection Current 19.9 11.6 6.4 27.2 16.6 7.2

Locked Rotor Amps 104.0 83.1 41 152.9 110.0 52.0

ENERGY RECOVERY VENTILATOR

Volts 230/208-60-1 230/208-60-1

Full Load Amps (3-motors) 2.2 2.2

FAN MOTOR – ECM

Horsepower 1/2 1/2

Volts 230/208-60-1 230/208-60-1

Full Load Amps 3.2 3.2

+ CFM 2600 2600

BLOWER MOTOR – ECM

Horsepower 1/2 3/4

Volts 230/208-60-1 230/208-60-1

Full Load Amps 3.2 4.4

+ CFM @ rating points, will modulate based upon O.D. ambient.

+ CFM @ rating points, will modulate based upon O.D. ambient.

• Complies with efficiency requirements of ANSI/ASHRAE/IESNA 90.1-2013.• Certified to ANSI/ARI Standard 390-2003 for SPVU (Single Package Vertical Units).• Intertek ETL Listed to Standard for Safety Heating and Cooling Equipment ANSI/UL 1995/CSA 22.2 No. 236-05, Fourth Edition.• Intertek ETL Listed to Standard for Gas-Fired Central Furnaces ANSI Z21.47-2006, CSA 2.3-2006 Fifth Edition, Addenda A dated 10-01-2007, Addenda B dated 06-01-2008.• Commercial Product - Not intended for Residential application.

Bard is anISO 9001:2015

Certified Manufacturer

MODELS I30H1-A I30H1-B I30H1-C I36H1-A I36H1-B I36H1-C I42H1-A I42H1-B I42H1-C

ELECTRICAL RATING--60 HZ 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3

Operating Voltage Range 197-253 414-506 197-253 414-506 197-253 414-506

COMPRESSOR

Volts 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3 230/208-1 230/208-3 460-3

Rated Load Amps (230/208) 10.0/11.5 7.4/8.4 4.2 11.1/13 8.5/9.9 4.9 13.8/15.6 11.0/12.4 5.5

Branch Circuit Selection Current 13.1 8.7 4.3 15.3 11.7 5.8 18.0 14.2 6.3

Locked Rotor Amps 73 58 28 83 73 38 96 88 44

ENERGY RECOVERY VENTILATOR

Volts 230/208-60-1 230/208-60-1 230/208-60-1

Full Load Amps (3-motors) 2.2 2.2 2.2

FAN MOTOR – ECM

Horsepower 1/3 1/3 1/3

Volts 230/208-60-1 230/208-60-1 230/208-60-1

Full Load Amps 1.7 2.6 2.6

+ CFM 1950 2300 2300

BLOWER MOTOR – ECM

Horsepower 1/3 1/2 1/2

Volts 230/208-60-1 230/208-60-1 230/208-60-1

Full Load Amps 1.9 2.5 2.5

Page 3: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 3 of 20

Capacity and Efficiency Ratings (Stage 1) Part Load Operation

EER = Energy Efficiency Ratio - BTU/WATT efficiency IPLV = Integrated Part Load Value - BTU/WATT efficiency (combines full and part load performance) COP = Coefficient of Performance - BTU/WATT efficiency

Motor will deliver consistent CFM through voltage supply range with no deterioration. Continous fan CFM is the total air being circulated during continuous fan mode. Will operate @ rated Full Load Airflow when operating with Heat Pump. Will occur automatically with a call for "W3" or "Emergency Heat" signal from thermostat (Heat Pump Operation is terminated @ this condition).

Capacity and Efficiency Ratings (Stage 2) Full Load Operation

Indoor Blower Performance

Unit Weights

Model RatedESP.

Max.ESP

Continuous

CFM

Rated2nd Stage

CFM

Rated1st Stage

CFM

4-10 KW

CFM

15-20 KW

CFM

I30H1 0.15 0.50 500 900 650 700 1050

I36H1 0.15 0.50 600 1150 850 700 1050

I42H1 0.20 0.50 650 1300 950 700 1050

I48H1 0.20 0.50 725 1500 1050 700 1400

I60H1 0.20 0.50 850 1700 1200 700 1400

Deduct 49# from all values for installed weight.

MODELS I30H1 I36H1 I42H1 I48H1 I60H1

Cooling BTUH, Full Load Capacity, 95-80/67 EER Rated CFM

27,80011.7900

35,00012.01150

41,50012.01300

47,00012.01500

54,00011.21700

IPLV (Integrated Full & Part Load) 80-80/67 15.4 16.5 15.7 16.1 15.5

Heating BTUH, Full Load Capacity 47/43-70 COP Rated CFM

26,6003.6900

32,8003.7

1150

38,5003.7

1300

44,5003.7

1500

54,0003.6

1700

MODELS I30H1 I36H1 I42H1 I48H1 I60H1

Cooling BTUH, Part Load Capacity, 80-80/67 EER Rated CFM

22,80015.4650

27,60016.6850

32,00016.15950

36,00016.21050

41,00014.551200

Heating BTUH, Part Load Capacity 47/43-70 COP Rated CFM

19,8003.5650

22,8003.6850

27,0003.6950

30,5003.6

1050

36,5003.4

1200

MODELS NO VENT CRV ERV

I30H1-A 816 908 943

I30H1-B 816 908 943

I30H1-C 851 943 978

I36H1-A 846 938 973

I36H1-B 846 938 973

I36H1-C 881 973 1008

I42H1-A 896 988 1023

I42H1-B 896 988 1023

I42H1-C 931 1023 1058

I48H1-A 884 976 1011

I48H1-B 884 976 1011

I48H1-C 919 1011 1046

I60H1-A 931 1023 1058

I60H1-B 931 1023 1058

I60H1-C 966 1058 1093

MODELS NO VENT CRV ERV

I30H1DA 830 920 955

I30H1DB 830 920 955

I30H1DC 865 955 990

I36H1DA 858 950 985

I36H1DB 858 950 985

I36H1DC 893 985 1020

I42H1DA 908 1000 1035

I42H1DB 908 1000 1035

I42H1DC 943 1035 1070

I48H1DA 930 1022 1057

I48H1DB 930 1022 1057

I48H1DC 965 1057 1092

I60H1DA 943 1035 1070

I60H1DB 943 1035 1070

I60H1DC 978 1070 1105

Page 4: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 4 of 20

Hot Water Coil Correction FactorsEntering Air Temp

(F)

Entering Water Temperature (F)

100 110 120 130 140 150 160 170 180 190 200

50 0.455 0.545 0.636 0.727 0.818 0.909 1.000 1.091 1.182 1.273 1.364

55 0.409 0.500 0.591 0.682 0.773 0.864 0.955 1.045 1.136 1.227 1.318

60 0.363 0.455 0.545 0.636 0.727 0.818 0.909 1.000 1.091 1.182 1.273

65 0.318 0.409 0.500 0.591 0.682 0.773 0.864 0.955 1.045 1.136 1.227

70 0.272 0.363 0.455 0.545 0.636 0.727 0.818 0.909 1.000 1.091 1.182

75 0.227 0.318 0.409 0.500 0.591 0.682 0.773 0.864 0.955 1.045 1.136

80 0.182 0.272 0.363 0.455 0.545 0.636 0.727 0.818 0.909 1.000 1.091

GPMCFM

800 900 1000 1100 1200 1300 1400 1500 1600 1700

1.5 32,000 32,667 33,333 34,000 34,500 35,000 35,500 36,000 36,400 36,750

2 42,000 43,200 44,400 45,600 46,400 47,200 48,000 48,500 49,000 49,500

3 49,000 51,667 53,750 57,000 59,400 61,750 64,000 65,200 66,000 67,000

4 56,000 59,000 62,000 65,000 69,000 73,000 77,000 79,500 82,000 84,000

5 59,000 62,583 66,167 69,750 72,833 75,917 79,000 81,000 83,000 85,000

6 62,000 66,167 70,333 74,500 77,000 79,500 82,000 83,500 85,000 86,500

7 63,500 67,708 71,917 76,125 78,917 81,708 84,500 86,500 88,000 89,200

8 65,000 69,250 73,500 77,750 80,833 83,917 87,000 88,900 90,500 91,750

9 66,000 70,525 75,050 79,575 82,883 86,192 89,500 91,500 93,000 94,500

10 67,000 71,800 76,600 81,400 84,933 88,467 92,000 94,500 96,000 97,500

Factory Built-in Electric Heat Table

Model Voltage PhaseKW Amps BTUH

240 208 240 208 240 208

-A04 240/208 1 4 3 16.7 14.4 13,652 10,239

-A05 240/208 1 5.00 3.75 20.8 18.0 17,065 12,799

-A10 240/208 1 10.00 7.50 41.7 36.1 34,130 25,598

-A15 240/208 1 15.00 11.25 62.5 54.1 51,195 38,396

-A20 240/208 1 20.00 15.00 83.3 72.1 68,260 51,195

-B06 240/208 3 6.00 4.50 14.4 12.5 20,478 15,359

-B09 240/208 3 9.00 6.75 21.7 18.7 30,717 23,038

-B15 240/208 3 15.00 11.25 36.1 31.2 51,195 38,396

-B18 240/208 3 18.00 13.50 43.3 37.5 61,434 46,076

NOTE: Not all KW's available in all models. See Minimum Circuit Ampacity and Maximum Overcurrent Protection table on following page.

Optional IHWC Hot Water Coil Performance

Model Voltage PhaseKW Amps BTUH

480V 460V 480V 460V 480V 460V

-C06 480 3 6.00 5.52 7.2 6.9 20,478 18,840

-C09 480 3 9.00 8.28 10.8 10.4 30,717 28,260

-C15 480 3 15.00 13.80 18.0 17.3 51,195 47,099

-C18 480 3 18.00 16.56 21.7 20.8 61,434 56,519

Page 5: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 5 of 20

These “Minimum Circuit Ampacity” values are to be used for sizing the field power conductors. Refer to the National Electric Code (latest revision), Article 310 for power conductor sizing.Caution: When more than one field power conductor circuit is run through one conduit, the conductors must be derated. Pay special attention to note 8 of table 310 regarding Ampacity Adjustment Factors when more than three (3) current carrying conductors are in a raceway.Maximum size of the time delay fuse or HVAC type circuit breaker for protection of field wiring conductors.Based on 75°C copper wire. All wiring must conform to the National Electrical Code and all local codes.Maximum KW that can operate with the heat pump is 10KW for 1-Phase and 9KW for 3-Phase. Represents Electric Heat only. Electric Control Circuit will lock-out Heat Pump Operation.

Minimum Circuit Ampacity & Maximum Overcurrent Protection – Std. & Dehum.

MODEL

Rated Volts,

Hertz & Phase

Single Circuit Dual Circuit

No. Field Power

Circuits

Minimum Circuit

Ampacity

Maximum External Fuse or

Ckt. Brkr.

Field Power

Wire Size

Ground Wire

Minimum Circuit

Ampacity

MaximumExternal

Fuse or Ckt. Breaker

Field Power Wire Size

Ground Wire Size

Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B

I30H1-A0ZA05A10

230/208-111

1 or 2

224874

355080

884

10108 48 30 50 30 8 10 10 10

I30H1-B0ZB06B09

230/208-3111

173544

253545

1088

101010

I30H1-C0ZC06C09

460-3111

91822

102025

141210

141210

I36H1-A0ZA05A10

A15

230/208-1

11

1 or 21 or 2

26527884

40608090

8644

101088

2626

5252

4040

6060

88

66

1010

1010

I36H1-B0ZB06B09

B15

230/208-3

1111

22404951

30455060

10886

10101010

I36H1-C0ZC06C09

C15

460-3

1111

11202428

15202530

14121010

14121010

I42H1-A0ZA05A10

A15

230/208-1

11

1 or 21 or 2

30568282

45609090

8644

101088

5656

2652

6060

3060

66

86

1010

1010

I42H1-B0ZB06B09

B15

230/208-3

1111

25435252

35506060

10866

10101010

I42H1-C0ZC06C09

C15

460-3

1111

12212628

15253030

14101010

14101010

I48H1-A0ZA04A05A10

A15 A20

230/208-1

11

1 or 21 or 21 or 21 or 2

3454598585

110

5060709090

110

866332

10108886

35353559

26525252

45454560

30606060

8886

10666

10101010

10101010

I48H1-B0ZB06B09

B15 B18

230/208-3

11111

2644535353

3550606060

108666

1010101010

I48H1-C0ZC06C09

C15 C18

460-3

11111

1221262626

1530303030

1410101010

1410101010

I60H1-A0ZA05A10

A15 A20

230/208-1

11 or 21 or 21 or 21 or 2

44709696

112

6080

100100120

84332

108886

44444460

26525252

60606060

30606060

8886

10666

10101010

10101010

I60H1-B0ZB06B09

B15 B18

230/208-3

11112

31495858–

45606060–

8866–

10101010– 31 54 45 60 8 6 10 10

I60H1-C0ZC06C09

C15 C18

460-3

11111

1525292929

2030303030

1210101010

1210101010

Page 6: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 6 of 20

Model D.B. / W.B.

COOLING CAPACITY 60°F 65°F 70°F 75°F 80°F 85°F 90°F 95°F 100°F 105°F 110°F 115°F 120°F 125°F

I30H1

75/62Total CoolingSensible Cooling

30,76423,517

30,05623,129

29,34922,741

28,64122,352

27,93421,964

27,22621,575

26,51921,187

25,81220,799

24,97620,596

24,14020,393

23,30520,191

22,46919,988

21,63319,785

20,79819,583

80/67Total CoolingSensible Cooling

33,48823,981

32,67523,488

31,86322,994

31,05022,500

30,20022,000

29,38821,506

28,61321,019

27,80020,525

26,90020,325

26,00020,125

25,10019,925

24,20019,725

23,30019,525

22,40019,325

85/72Total CoolingSensible Cooling

35,99023,806

35,37223,272

34,75422,738

34,13622,204

33,51821,671

32,90021,137

32,28220,603

31,66420,069

30,63919,873

29,61419,678

28,58919,482

27,56419,287

26,53919,091

25,51418,896

I36H1

75/62Total CoolingSensible Cooling

39,01330,182

38,16129,782

37,31029,383

36,45928,983

35,60828,584

34,75628,184

33,90527,785

33,05427,385

31,80026,853

30,54726,321

29,29325,789

28,04025,257

26,78724,725

25,53324,193

80/67Total CoolingSensible Cooling

42,46930,788

41,48830,250

40,50629,713

39,52529,175

38,50028,600

37,51928,063

36,58127,563

35,00027,025

34,25026,500

32,90025,975

31,55025,450

30,20024,925

28,85024,400

27,50023,875

85/72Total CoolingSensible Cooling

45,63230,567

44,90629,975

44,18029,384

43,45428,792

42,72728,200

42,00127,608

41,27527,016

40,54826,424

39,01125,911

37,47325,398

35,93524,884

34,39824,371

32,86023,858

31,32323,344

I42H1

75/62Total CoolingSensible Cooling

46,86535,042

45,74034,686

44,61634,331

43,49233,975

42,36833,620

41,24433,264

40,12032,909

38,99632,553

38,00632,198

37,01531,843

36,02531,488

35,03531,133

34,04530,778

33,05430,423

80/67Total CoolingSensible Cooling

51,01335,756

49,72535,238

48,43834,719

47,15034,200

44,50032,675

43,21332,156

43,28832,644

41,50032,125

40,93331,775

39,86731,424

38,80031,074

37,73430,723

36,66730,373

35,60130,022

85/72Total CoolingSensible Cooling

54,83535,505

53,83634,921

52,83634,336

51,83633,751

50,83733,166

49,83732,581

48,83831,996

47,83831,411

46,62331,068

45,40830,726

44,19430,383

42,97930,040

41,76429,698

40,54929,355

I48H1

75/62Total CoolingSensible Cooling

51,84339,521

50,51238,811

49,18038,101

47,84937,391

46,51736,681

45,18535,971

43,85435,261

42,52234,551

40,91033,856

39,29933,161

37,68732,466

36,07631,771

34,46431,076

32,85230,381

80/67Total CoolingSensible Cooling

56,91338,814

55,49738,219

54,08137,624

52,66437,029

51,00035,950

49,58435,355

48,41635,245

47,00034,650

45,21933,953

43,43733,256

41,65632,559

39,87531,862

38,09331,165

36,31230,467

85/72Total CoolingSensible Cooling

54,00838,517

53,71237,839

53,41637,162

53,12036,484

52,82335,806

52,52735,129

52,23134,451

50,40833,795

48,58533,138

46,76132,482

44,93831,825

43,11531,169

41,29230,513

39,46929,856

I60H1

75/62Total CoolingSensible Cooling

61,06245,691

59,31844,741

57,57543,790

55,83142,840

54,08741,890

52,34340,939

50,59939,989

48,85539,039

47,36638,482

45,87737,926

44,38737,370

42,89836,813

41,40936,257

39,91935,701

80/67Total CoolingSensible Cooling

67,03844,881

65,17544,063

63,31343,244

61,45042,425

59,58841,606

57,72540,788

55,86339,969

54,00039,150

52,35438,592

50,70838,034

49,06237,476

47,41536,918

45,76936,360

44,12335,802

85/72Total CoolingSensible Cooling

72,83444,530

70,73943,620

68,64442,710

66,55041,800

64,45540,890

62,36039,980

60,26539,070

58,17038,160

56,39737,616

54,62437,072

52,85136,528

51,07735,985

49,30435,441

47,53134,897

Model D.B. / W.B. k

COOLING CAPACITY 60°F 65°F 70°F 75°F 80°F 85°F 90°F 95°F 100°F 105°F 110°F 115°F 120°F 125°F

I30H1

75/62Total CoolingSensible Cooling

24,11118,256

23,36317,908

22,61517,561

21,86817,214

21,12016,866

20,37216,519

19,62516,172

18,87715,825

18,21215,526

17,54815,227

16,88414,929

16,21914,630

15,55514,332

14,89114,033

80/67Total CoolingSensible Cooling

26,02518,000

25,25017,700

24,47517,400

23,70017,100

22,80016,675

22,02516,375

21,37516,200

22,80015,900

19,87515,600

19,15015,300

18,42515,000

17,70014,700

16,97514,400

16,25014,100

85/72Total CoolingSensible Cooling

27,26717,242

26,72917,056

26,19016,869

25,65216,683

25,11316,497

24,57516,310

24,03716,124

23,49815,938

22,67115,637

21,84415,336

21,01715,036

20,19014,735

19,36314,434

18,53614,133

I36H1

75/62Total CoolingSensible Cooling

29,64523,790

28,68323,242

27,72022,694

26,75822,146

25,79621,599

24,83321,051

23,87120,503

22,90919,955

22,23319,743

21,55719,532

20,88119,321

20,20619,109

19,53018,898

18,85418,686

80/67Total CoolingSensible Cooling

32,00023,463

31,00022,975

30,00022,488

29,00022,000

27,60021,175

26,60020,688

26,00020,538

27,60020,050

24,26319,838

23,52519,625

22,78819,413

22,05019,200

21,31318,988

20,57518,775

85/72Total CoolingSensible Cooling

33,54222,488

32,82422,146

32,10621,805

31,38821,463

30,67021,122

29,95320,780

29,23520,439

28,51720,098

27,67619,885

26,83519,672

25,99319,459

25,15219,246

24,31119,033

23,47018,819

I42H1

75/62Total CoolingSensible Cooling

30,06425,169

29,63124,766

29,19824,362

28,76523,958

28,33223,555

27,89923,151

27,46522,747

27,03222,344

26,09122,055

25,15021,767

24,20921,479

23,26821,191

22,32720,903

21,38620,615

80/67Total CoolingSensible Cooling

32,43124,813

32,01324,475

31,59424,138

31,17523,800

32,00023,600

31,58123,263

29,91922,788

32,00022,450

28,47322,160

27,44621,871

26,41921,581

25,39221,292

24,36521,002

23,33820,713

85/72Total CoolingSensible Cooling

33,81123,757

33,78823,578

33,76523,399

33,74223,220

33,71923,040

33,69622,861

33,67322,682

33,65022,503

32,47922,213

31,30721,923

30,13621,633

28,96421,342

27,79321,052

26,62220,762

I48H1

75/62Total CoolingSensible Cooling

36,48927,440

35,47726,922

34,46526,404

33,45325,886

32,44125,369

31,42924,851

30,41724,333

29,40523,815

28,40423,512

27,40323,210

26,40222,907

25,40122,604

24,40022,302

23,39921,999

80/67Total CoolingSensible Cooling

40,38027,189

39,25526,712

38,12926,234

37,00325,756

36,00025,241

34,87424,763

33,62624,323

32,50023,845

31,39423,542

30,28823,239

29,18122,936

28,07522,633

26,96922,330

25,86322,027

85/72Total CoolingSensible Cooling

37,19426,876

36,98726,403

36,78025,930

36,57325,457

36,36624,984

36,15924,511

35,95224,038

35,74523,565

34,52923,265

33,31222,966

32,09522,666

30,87922,367

29,66222,067

28,44521,768

I60H1

75/62Total CoolingSensible Cooling

42,80531,549

41,47230,890

40,13930,232

38,80729,574

37,47428,916

36,14228,258

34,80927,599

33,47626,941

32,48726,585

31,49726,230

30,50825,874

29,51825,518

28,52825,162

27,53924,806

80/67Total CoolingSensible Cooling

47,36931,263

45,88830,650

44,40630,038

42,92529,425

41,00028,500

39,51927,888

38,48127,588

41,00026,975

35,90626,619

34,81326,263

33,71925,906

32,62525,550

31,53125,194

30,43824,838

85/72Total CoolingSensible Cooling

51,94130,902

50,33430,296

48,72829,690

47,12129,083

45,51528,477

43,90827,870

42,30127,264

40,69526,658

39,49226,306

38,28925,954

37,08625,602

35,88325,250

34,68024,897

33,47724,545

Below 50°F, unit requires a factory or field installed low ambient control. Return air temp. °F Rated CFM.

Cooling Part Load Application Data

Cooling Full Load Application Data

Page 7: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 7 of 20

Heating Full Load Application Data

Heating Part Load Application Data

70°F DB indoor return air at rated CFM includes defrost operation below 45°.

70°F DB indoor return air at rated CFM includes defrost operation below 45°.

Unit Charge Rates

UNIT Std. Unit - Lbs.

Dehum. Units - Lbs.

I30H1 - High Efficiency Step Capacity Indoor HP

7.75 8.6250

I36H1 - High Efficiency Step Capacity Indoor HP

10.5625 10.9375

I42H1 - High Efficiency Step Capacity Indoor HP

10.75 11.1875

I48H1 - High Efficiency Step Capacity Indoor HP

12.9375 13.8125

I60H1 - High Efficiency Step Capacity Indoor HP

12.875 13.3125

Model Indoor 0° 5° 10° 15° 20° 25° 30° 35° 40° 45° 50° 55° 60°F

I30H1

70°F

BTUHWATTS

COP

10,66318791.66

12,52519061.93

14,38819272.19

16,25019432.45

18,11319562.71

19,97519672.98

21,83819763.24

23,7001984

3.5

25,00020463.58

26,30021053.66

28,06021823.77

29,82022543.88

31,58023233.98

I36H1BTUH

WATTSCOP

12,81918042.08

14,78819392.24

16,75620562.39

18,72521602.54

20,69422522.69

22,66323342.85

24,63124083.00

26,60024743.15

29,40024613.50

32,20024513.85

34,20025113.99

36,20025684.13

38,20026214.27

I42H1BTUH

WATTSCOP

21,13826642.33

22,27526642.45

23,41326642.58

24,55026642.70

25,68826642.83

26,82526642.95

27,96326643.08

29,1002664

3.2

33,65027773.55

38,20028703.90

40,20029234.03

42,20029724.16

44,20030194.29

I48H1BTUH

WATTSCOP

19,80624332.39

22,51326602.48

25,21928702.58

27,92530642.67

30,63132462.77

33,33834152.86

36,04435742.96

38,75037233.05

41,26335353.42

43,77533843.79

46,82034893.93

49,86535864.07

52,91036774.22

I60H1BTUH

WATTSCOP

30,46940122.23

31,68839512.35

32,90638962.48

34,1253846

2.6

35,344 38002.73

36,563 37592.85

37,781 37212.98

39,000 3686

3.1

46,050 40583.33

53,10043833.55

56,60045063.68

60,10046223.81

63,60047303.94

Model Indoor 0° 5° 10° 15° 20° 25° 30° 35° 40° 45° 50° 55° 60°F

I30H1

70°F

BTUHWATTS

COP

6,55015201.26

8,10015561.53

9,65015821.79

11,20016012.05

12,75016152.31

14,30016272.58

15,85016372.84

17,40016453.10

18,50016603.27

19,60016743.43

21,12017173.60

22,64017563.78

24,16017913.95

I36H1BTUH

WATTSCOP

8,98116001.65

10,31316691.81

11,64417271.98

12,97517762.14

14,30618192.31

15,63818552.47

16,96918872.64

18,30019152.80

20,30018913.15

22,30018723.49

24,06018693.77

25,82018664.05

27,58018644.34

I42H1BTUH

WATTSCOP

10,16919851.50

11,88820221.72

13,60620511.94

15,32520742.17

17,04420932.39

18,76321082.61

20,48121212.83

22,20021333.05

24,27521723.28

26,3502206

3.5

28,11021903.76

29,87021774.02

31,63021654.28

I48H1BTUH

WATTSCOP

12,58823231.59

14,47523891.78

16,36324431.96

18,25024872.15

20,13825242.34

22,02525562.53

23,91325832.71

25,8002607

2.9

27,70025243.22

29,600 2,457

3.53

32,05025183.73

34,50025723.93

36,95026214.13

I60H1BTUH

WATTSCOP

12,61321331.73

15,22523671.89

17,83825652.04

20,45027362.19

23,06328852.34

25,67530152.50

28,28831312.65

30,90032332.80

33,13831473.09

35,37530763.37

38,17032013.49

40,96533173.62

43,76034263.74

Page 8: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 8 of 20

Performance and Application Data – Energy Recovery Vent Option "R"

LEGEND:

VLT = Ventilation Load - TotalVLS = Ventilation Load - SensibleVLL = Ventilation Load - LatentHRT = Heat Recovery - TotalHRS = Heat Recovery - SensibleHRL = Heat Recovery - LatentWVL = Winter Ventilation LoadWHR = Winter Heat Recovery

SUMMER COOLING PERFORMANCE(INDOOR DESIGN CONDITIONS 75°DB/62°WB)

AmbientO.D.

VENTILATION RATE 450 CFM65% EFFICIENCY

VENTILATION RATE 375 CFM66% EFFICIENCY

VENTILATION RATE 300 CFM67% EFFICIENCY

DB/WB F VLT VLS VLL HRT HRS HRL VLT VLS VLL HRT HRS HRL VLT VLS VLL HRT HRS HRL

105

75 21465 14580 6884 13952 9477 4475 17887 12150 5737 11805 8018 3786 14310 9720 4590 9587 6512 3075

70 14580 14580 0 9477 9477 0 12150 12150 0 8018 8018 0 9720 9720 0 6512 6512 0

65 14580 14580 0 9477 9477 0 12150 12150 0 8018 8018 0 9720 9720 0 6512 6512 0

100

80 31590 12150 19440 20533 7897 12635 26325 10125 16200 17374 6682 10692 21060 8100 12960 14110 5427 8683

75 21465 12150 9314 13952 7897 6054 17887 10125 7762 11805 6682 5123 14310 8100 6210 9587 5427 4160

70 12352 12150 202 8029 7897 131 10293 10125 168 6793 6682 111 8235 8100 135 5517 5427 90

65 12150 12150 0 7897 7897 0 10125 10125 0 6682 6682 0 8100 8100 0 5427 5427 0

60 12150 12150 0 7897 7897 0 10125 10125 0 6682 6682 0 8100 8100 0 5427 5427 0

95

80 31590 9720 21870 20533 6318 14215 26325 8100 18225 17374 5345 12028 21060 6480 14580 14110 4341 9768

75 21465 9720 11744 13952 6318 7634 17887 8100 9787 11805 5345 6459 14310 6480 7830 9587 4341 5246

70 12352 9720 2632 8029 6318 1711 10293 8100 2193 6793 5345 1447 8235 6480 1755 5517 4341 1175

65 9720 9720 0 6318 6318 0 8100 8100 0 5345 5345 0 6480 6480 0 4341 4341 0

60 9720 9720 0 6318 6318 0 8100 8100 0 5345 5345 0 6480 6480 0 4341 4341 0

90

80 31590 7290 24300 20533 4738 15794 26325 6075 20250 17374 4009 13365 21060 4860 16200 14110 3256 10854

75 21465 7290 14175 13952 4738 9213 17887 6075 11812 11805 4009 7796 14310 4860 9450 9587 3256 6331

70 12352 7290 5062 8029 4738 3290 10293 6075 4218 6793 4009 2784 8235 4860 3375 5517 3256 2261

65 7290 7290 0 4738 4738 0 6075 6075 0 4009 4009 0 4860 4860 0 3256 3256 0

60 7290 7290 0 4738 4738 0 6075 6075 0 4009 4009 0 4860 4860 0 3256 3256 0

85

80 31590 4860 26730 20533 3159 17374 26325 4050 22275 17374 2672 14701 21060 3240 17820 14110 2170 11939

75 21465 4860 16605 13952 3159 10793 17887 4050 13837 11805 2672 9132 14310 3240 11070 9587 2170 7416

70 12352 4860 7492 8029 3159 4870 10293 4050 6243 6793 2672 4120 8235 3240 4995 5517 2170 3346

65 4860 4860 0 3159 3159 0 4050 4050 0 2672 2672 0 3240 3240 0 2170 2170 0

60 4860 4860 0 3159 3159 0 4050 4050 0 2672 2672 0 3240 3240 0 2170 2170 0

80

75 21465 2430 19035 13952 1579 12372 17887 2025 15862 11805 1336 10469 14310 1620 12690 9587 1085 8502

70 12352 2430 9922 8029 1579 6449 10293 2025 8268 6793 1336 5457 8235 1620 6615 5517 1085 4432

65 4252 2430 1822 2764 1579 1184 3543 2025 1518 2338 1336 1002 2835 1620 1215 1899 1085 814

60 2430 2430 0 1579 1579 0 2025 2025 0 1336 1336 0 1620 1620 0 1085 1085 0

75

70 12352 0 12352 8029 0 8029 10293 0 10293 6793 0 6793 8235 0 8235 5517 0 5517

65 4252 0 4252 2764 0 2764 3543 0 3543 2338 0 2338 2835 0 2835 1899 0 1899

60 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

WINTER HEATING PERFORMANCE(INDOOR DESIGN CONDITIONS 70°F DB)

AmbientO.D.

VENTILATION RATE

450 CFM80% EFFICIENCY

375 CFM81% EFFICIENCY

300 CFM82% EFFICIENCY

DB/°F WVL WHR WVL WHR WVL WHR

65 2430 1944 2025 1640 1620 1328

60 4860 3888 4050 3280 3240 2656

55 7290 5832 6075 4920 4860 3985

50 9720 7776 8100 6561 6480 5313

45 12150 9720 10125 8201 8100 6642

40 14580 11664 12150 9841 9720 7970

35 17010 13608 14175 11481 11340 9298

30 19440 15552 16200 13122 12960 10627

25 21870 17496 18225 14762 14580 11955

20 24300 19440 20250 16402 16200 13284

15 26730 21384 22275 18042 17820 14612

NOTE: Sensible performance only is shown for winter application.

Page 9: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 9 of 20

I-TEC Accessory Model Numbers

Above table based on I-TEC unit being installed flush to inside of wall. 8" Depth Storm Louvers are field supplied

Available Special Order and requires additional lead-time. Reference Form S3508 for additional details.• Custom Finishes are quoted on a project-by-project basis and pricing is determined by quantity, finish option and size.• Custom Finishes are ordered/shipped directly from the louver supplier.• Purchaser of Custom Finishes assumes liability for quantity, finish match and size.• Contact your Bard Sales Representative for custom louver contact information.

Wall Sleeves (Required Option - Select One)

Model # Description Total Depth of Wall System When Used with 1" Louver

Total Depth of Wall System When Used with 2" Louver

IWS-A Wall Sleeve Adjustable 5.5 to 8.5" 6.5 to 8.5"

IWS-B Wall Sleeve Adjustable 8.0 to 13.5" 9.0 to 13.5"

IWS-C Wall Sleeve Adjustable 13.0 to 23.5" 14.0 to 23.5"

Model # Description Total Depth of Wall System When Used with 4" Louver

Total Depth of Wall System When Used with 8" Louver

IWS-A8H Wall Sleeve Adjustable 8.0 to 12.0" —

IWS-B8H Wall Sleeve Adjustable 12.0 to 20.0" 12.0 to 15.0"

IWS-C8H Wall Sleeve Adjustable — 15.0 to 20.5"

Outdoor Louver Grilles (Required Option - Select One)

Model # Description Color Sleeve (Required)

ILS1-10 1" Standard Anodized Aluminum IWS-A, -B, -C

ILS1-20 1" Standard Aluminum with Medium Bronze Finish IWS-A, -B, -C

ILS1-30 1" Standard Aluminum with Dark Bronze Finish IWS-A, -B, -C

ILS1-** 1" Standard Aluminum with Custom Finish IWS-A, -B, -C

ILA2-10 2" Architectural Anodized Aluminum IWS-A, -B, -C

ILA2-20 2" Architectural Aluminum with Medium Bronze Finish IWS-A, -B, -C

ILA2-30 2" Architectural Aluminum with Dark Bronze Finish IWS-A, -B, -C

ILA2-** 2" Architectural Aluminum with Custom Finish IWS-A, -B, -C

ILST4-10 4" Storm Anodized Aluminum IWS-AH, -BH, -CH

ILST4-20 4" Storm Aluminum with Medium Bronze Finish IWS-AH, -BH, -CH

ILST4-30 4" Storm Aluminum with Dark Bronze Finish IWS-AH, -BH, -CH

ILST4-** 4" Storm Aluminum with Custom Finish IWS-AH, -BH, -CH

Additional Louver Colors Available — Applies to ILS, ILA and ILST Louvers

-12 Arctic White

-14 Storm White

-18 Milano Beige

-32 Jet Black

-36 Graphite Gray

-40 School Bus Yellow

-42 Florida Orange

-44 School House Red

-46 Chili Red

-50 Deep Sea Blue

-52 Bahama Blue

-54 Ivy Green

-56 Sage Green

Page 10: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 10 of 20

Duct-Free Plenum BoxesModel #: Description:IPBDFH18-X 18" Duct Free Plenum – Beige. Black linear slot grilles, side w/shutoff damperIPBDFH18-1 18" Duct Free Plenum – White. Black linear slot grilles, side w/shutoff damperIPBDFH18-4 18" Duct Free Plenum – Gray. Black linear slot grilles, side w/shutoff damperIPBDFH12-X 12" Duct Free Plenum – Beige. Black linear slot grilles, side w/shutoff damperIPBDFH12-1 12" Duct Free Plenum – White. Black linear slot grilles, side w/shutoff damperIPBDFH12-4 12" Duct Free Plenum – Gray. Black linear slot grilles, side w/shutoff damperIPBDF18-X 18" Duct Free Plenum – Beige. (2) Anodized dual deflection front & side grillesIPBDF18-1 18" Duct Free Plenum – White. (2) Anodized dual deflection front & side grillesIPBDF18-4 18" Duct Free Plenum – Gray. (2) Anodized dual deflection front & side grillesIPBDF12-X 12" Duct Free Plenum – Beige. (2) Anodized dual deflection front & side grillesIPBDF12-1 12" Duct Free Plenum – White. (2) Anodized dual deflection front & side grillesIPBDF12-4 12" Duct Free Plenum – Gray. (2) Anodized dual deflection front & side grillesIPBDF8-X 8" Duct Free Plenum – Beige. Anodized dual deflection front & side grillesIPBDF8-1 8" Duct Free Plenum – White. Anodized dual deflection front & side grillesIPBDF8-4 8" Duct Free Plenum – Gray. Anodized dual deflection front & side grilles

Duct-Free Plenum Boxes with Hot Water CoilModel #: Description:IPBDF12HW-X 12" Duct Free Plenum–Beige. Anodized dual deflection front & side grilles, w/hot water coilIPBDF12HW-1 12" Duct Free Plenum–White. Anodized dual deflection front & side grilles, w/hot water coilIPBDF12HW-4 12" Duct Free Plenum–Gray. Anodized dual deflection front & side grilles, w/hot water coilNOTE: No water control valves included. Field-Installed.

Hot Water Coil with Duct ConnectionModel #: Description:IHWC Hot water coil assembly, mounts on top of I-TEC unit, 10" x 30" duct flangeNOTE: No water control valves included. Field-Installed.

NOTE: Order appropriate Cabinet Extension (Model ICX28-*) to enclose hot water coil assembly, valves, piping and ductwork.

Hot Water Coil Valves Model #: Description:5650-035 On/Off Water Valve, 3 way 3/4" 24V5650-047 Modulating Water Valve, 3 way 3/4" 24V

Cabinet ExtensionsModel #: Description:ICX28-X 28" extension for ceilings up to 10'2", beige paintICX28-1 28" extension for ceilings up to 10'2", white paint

ICX28-4 28" extension for ceilings up tp 10'2", gray paint

I-TEC Accessories — Optional per Job Requirement

Riser PlatformsModel #: Description: Model #: Description:IRP-3-X Riser platform 3" with trim kit, beige paint IRP-11-X Riser platform 11" with trim kit, beige paintIRP-3-1 Riser platform 3" with trim kit, white paint IRP-11-1 Riser platform 11" with trim kit, white paintIRP-3-4 Riser platform 3" with trim kit, gray paint IRP-11-4 Riser platfrom 11" with trim kit, gray paintIRP-6-X Riser platform 6" with trim kit, beige paint IRP-14-X Riser platform 14" with trim kit, beige paintIRP-6-1 Riser platform 6" with trim kit, white paint IRP-14-1 Riser platform 14" with trim kit, white paintIRP-6-4 Riser platform 6" with trim kit, gray paint IRP-14-4 Riser platform 14" with trim kit, gray paintIRP-9-X Riser platform 9" with trim kit, beige paintIRP-9-1 Riser platform 9" with trim kit, white paintIRP-9-4 Riser platform 9" with trim kit, gray paint

NOTE: Use of Riser Platforms will increase maximum ceiling height by riser height.

Page 11: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 11 of 20

Wall CurbsModel #: Description:ICURB740 7" Deep Curb to allow sleeve installation with a 40" window sill height

Side Trim KitsModel #: Description:IST4-X 4" Side Trim Kit, beige paint, adaptable for ceilings up to 12'IST4-1 4" Side Trim Kit, white paint, adaptable for ceilings up to 12'IST4-4 4" Side Trim Kit, gray paint, adaptable for ceilings up to 12'IST4L-X 4" Side Trim Kit, beige paint, adaptable for ceilings up to 12' 10"IST4L-1 4" Side Trim Kit, beige paint, adaptable for ceilings up to 12' 10"IST4L-4 4" Side Trim Kit, beige paint, adaptable for ceilings up to 12' 10"IST6-X 6" Side Trim Kit, beige paint, adaptable for ceilings up to 12'IST6-1 6" Side Trim Kit, white paint, adaptable for ceilings up to 12'IST6-4 6" Side Trim Kit, gray paint, adaptable for ceilings up to 12'IST10-X 10" Side Trim Kit, beige paint, adaptable for ceilings up to 12'IST10-1 10" Side Trim Kit, beige paint, adaptable for ceilings up to 12'IST10-4 10" Side Trim Kit, beige paint, adaptable for ceilings up to 12'

Other Optional AccessoriesModel #: Description:AHCK-2A Anti-Huffing Refrigerant Caps (Quantity 2) with KeySK111 Hard Start Kit for 1-Phase Models (I30H1-A, I36H1-A & I42H1-A) OnlySK118 Hard Start Kit for 1-Phase Models (I48H1-A & I60H1-A) Only

I-TEC Accessories — Optional per Job Requirement

Page 12: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 12 of 20

This page intentionally left blank.

Page 13: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 13 of 20

33 4"

241 2"

221 4"

Lowe

rSe

ction

713 4"

Uppe

rSe

ction

Slee

veInn

er

Retur

n

Slee

veOu

ter

Slee

veInn

er

Air

Retur

n

Slee

veOu

ter

Air

Supp

lyAi

r

(2) O

pt.Un

itDra

inEn

tranc

es

" 8 3

1

8"

31 8"

High

Volt

age

Entra

nce

Entra

nce

Low

Volta

ge

20"x

24" S

upply

Fram

e

24"

1 "

8

4

2"

26"

8

1 28

4""

3

"

3

Total

Depth

8

"1 2

4

4

11

20"

7

1 "11

4

"Tota

lWidt

h

31

547

346

1 8"W

ith S

idesR

emov

ed

Vent

Intak

e

Disc

onne

ctEl

ectric

al

AirF

ilters

Vent

Exha

ust

Door

Latch

Lock

ing

Filter

sRe

turn A

ir

(2)1

2"x2

0"

Door

Latch

Lock

ing

AirF

ilters

(2)W

asha

ble

Hing

es(4

)Lift-

Off

Contr

ol Pa

nel

Elec

tricHe

at Wire

Chan

nel

(2)2

"x24

"x30

"

Fron

tFor

kliftH

oles

(Rem

oveF

ront

Trim

)

"5

58"

" 15

84

131

94"

Total

Heigh

t

(2)R

eturn

Open

ings

Side

Forkl

iftHo

les(R

emov

e Side

s)

2" 71

1

30"W

ithDo

orsa

ndSi

desR

emov

ed

Uni

t Spe

cific

atio

n S

heet

Top

Vie

w

Rig

htS

ide

Vie

w

Fron

tVie

w

MIS-

2917

A

(2)U

nitDr

ains

(2) S

ideHa

ndles

Bac

kV

iew

Page 14: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 14 of 20

2

2 2

2

12" MIN.FOR RIGHT

SIDEACCESS

12" MIN.FOR LEFT

SIDEACCESS

12" MIN.12" MIN.

12" MIN. 12" MIN.

0" REQUIRED12" RECOMMENDED

0" REQUIRED12" RECOMMENDED

4"

4"

4"

4"

4"

48" MIN.

31 3/8"

12" MIN.12" MIN.

48"MIN. FOR

FILTER ACCESS

24" MIN. 24" MIN.

DRAIN ACCESS

VIEW FROM BACK OF UNIT

AREA

DRAIN ACCESS DETAIL

REMOVABLESIDES

ACCESSDRAIN

2

ACCESSDRAIN

MIS-3273 A

DRAINACCESS

DRAINACCESS

DRAINACCESS

12" MINIMUM DIMENSIONS AREREQUIRED FOR UNIT OPERATION.IT IS STRONGLY RECOMMENDEDTO USE 20" MINIMUM DISTANCESIF POSSIBLE FOR EASE OF UNITSERVICEABILITY

RECOMMENDED SERVICE

WING WALL CONSTRUCTION TOP VIEW

CLOSET CONSTRUCTION TOP VIEW

1

LEFT CORNER CONSTRUCTION TOP VIEW

FILTERSSIDESREMOVABLE

RIGHT CORNER CONSTRUCTION TOP VIEW

ACCESS DIMENSIONS

1 ALL FILTER AND COMPONENTACCESS IS FROM THE FRONT.COILS CAN BE CLEANED FROMTHE FRONT, BUT SIDES AREEASILY REMOVED FOR ENHANCEDACCESS.

DRAIN OUTLET

WALL/ROOM DRAIN

LONGER HOSEON SIDE WITH

WALL/ROOM DRAIN

DRAIN HEADER ASSEMBLY

TO DRAIN OUTLETSATTACH HEADER

CLAMPS AND

USE PROVIDEDCLAMPS TO SECURE

HEADER TO DRAIN OUTLETS

REMOVE NYLON

INSTALL DRAIN OUTLETON SAME SIDE AS

WALL DRAIN

MIS-3832MIS-3832

DRAIN ACCESS LOCATIONS

OPTIONAL UNIT DRAIN ENTRANCES

3/4" PVCDRAIN OUTLET

Page 15: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 15 of 20

"3 8 7

183 4"

17.5"

35"

ORSU

PPLY

DUCT

BOX

OPTI

ONAL

DUCT

GRILL

E

WAL

LSLE

EVE

IRP

RISE

RKI

T

UNIT

CEILI

NG

TELE

SCOP

ING

OPTI

ONAL

TRIM

FLOO

R

Open

ingCe

ntere

don

Optio

nalT

op

Wall

Moun

tingh

oles

(4)o

ption

alUn

it

Moun

tingh

oles

(4)o

ption

alUn

it

Brac

ket

Room

Floor

Leve

l

Outsi

de

Slee

veMo

untin

gHo

leLo

catio

ns

FLOO

RMO

UNTI

NGHO

LE&

CENT

ERLIN

ES

207

"

"

8"DI

M "B

""

6"

8720

8

2156

8"

207 8"

42-3

/4" M

in. 20"

15

"

"43

16

"

48" M

in.8

49

1

Cente

red

8

Cente

red

3"

48-1

/2" M

ax.

3

43-1

/4" M

ax.

20"

20"

DIM

"C"

11

20"

DIM

"A"

16

7

" 4

433 8"

1Hi

gher

SillH

eights

Achie

vable

With

IRP

Rise

rKit.

2Se

para

te tel

esco

pings

leeve

sava

ilable

ford

iffere

ntwa

ll thic

knes

ses.

Rig

htS

ide

Vie

wFr

ont (

Wal

lOnl

y)V

iew

Wal

l Sec

tion

Vie

w

MIS-

3306

A

C L

C L

IRP

RISE

RKI

TDI

M A

DIM

BDI

M C

NONE

31"-3

4"29

17/32

"94

1/8"

IRP-

3(3"

)34

"-37"

MAX

3217

/32"

971/8

"IR

P-6(

6")

37"-4

0" M

AX35

17/32

"10

01/8"

IRP-

9(9"

)40

"-43"

MAX

3817

32"

1031

/8"IR

P-11

(11"

)42

"-44"

MAX

4017

/32"

1051

/8"

1

2

Page 16: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 16 of 20

B

94"

A

7' - 10"

UNIT POWER THROUGHBOX IN CONDUIT

ROUTE LOW VOLTAGE

ROUTE HIGH VOLTAGEUNIT POWER THROUGHBOX IN CONDUIT

DIMENSIONS

MIS-3057 C

IPBDF8, IPBDF12 AND IPBDF18DUCT-FREE PLENUM BOX

MODEL NO. DIM. A DIM. BIPBDF8 8" 102" (8'-6")

IPBDF12 12" 106" (8'-10")IPBDF18 18" 112" (9'-4")

DIMENSIONAL CHART

B

MIS-3057 A

DIMENSIONS

IPBDFH8 AND IPBDFH12DUCT-FREE PLENUM BOX

7' - 10"

A

ROUTE LOW VOLTAGEUNIT POWER THROUGH

BOX IN CONDUIT

94"

ROUTE HIGH VOLTAGEUNIT POWER THROUGHBOX IN CONDUIT

MODEL NO. DIM. A DIM. BIPBDFH8 8" 102" (8'-6")IPBDFH12 12" 106" (8'-10")

DIMENSIONAL CHARTMIS-3057

IPBDF8, IPBDFH12 AND IPBDFH18DUCT-FREE PLENUM BOX

DIMENSIONS

DIMENSIONAL CHARTMODEL NO. DIM. A DIM. B

IPBDF8 8" 102" (8'-6")IPBDF12 12" 106" (8'-10")IPBDF18 18" 112" (9'-4")

IPBDFH12 12" 106" (8'-10")IPBDFH18 18" 112" (9'-4")

IPBDF12 AND IPBDF18DUCT-FREE PLENUM BOX

DIMENSIONS

Page 17: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 17 of 20

106"8' - 10"

BOX IN CONDUITUNIT POWER THROUGHROUTE HIGH VOLTAGE

HIGH VOLTAGE

ENTRANCEPOWER

MIS-3059

12"

ROUTE LOW VOLTAGEUNIT POWER THROUGH

BOX IN CONDUIT2"

TOP VIEW

7' - 10"94"

IPBDF12HWDUCT-FREE

HOT WATER COILDIMENSIONS

ENTRANCEVALVE WIRING

Ø7/8" O.D. WATER CONNECTIONS. NOTDESIGNATED AS "IN" OR "OUT". CAN BE PIPEDAS NEEDED FOR EASE OF VALVE INSTALLATIONAND SUPPLY/RETURN CONNECTIONS.

12" 12" 17 3/4"

8 3/16"

4 1/2"

Page 18: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 18 of 20

105"8' - 9"

ENTRANCELOW VOLTAGE

Ø7/8" O.D. WATER CONNECTIONS. NOTDESIGNATED AS "IN" OR "OUT". CAN BE PIPEDAS NEEDED FOR EASE OF VALVE INSTALLATIONAND SUPPLY/RETURN CONNECTIONS.

24 3/4"

9 7/8"

19 3/4"

40 7/8"

23 7/8"

29 7/8"

9 7/8"

8 1/4"

12"

DIMENSIONS

SUPPLY OPENING

TOP VIEW

7' - 10"

HOT WATER COILIHWC DUCTED

94"

ROUTE HIGH VOLTAGE

BOX IN CONDUITUNIT POWER THROUGH

11"

HIGH VOLTAGEPOWERENTRANCE

2.5"

MIS-3058

Page 19: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 19 of 20

1. dBA @ 10 feet, Values recorded in Bard Manufacturing Company, Inc. Sound Lab Facility.2. Actual field results may vary with classroom design and construction.3. Integrated values calculated per ANSI/ASA S12.60-2009 / Part 2, Section 5.2.2.1, Table 2 Triple Mode Type 3

HVAC System Duty Cycles: Ventilation 58%, Part Load 25%, Full Load 17%4. Integrated Sound Values are also applicable for use in learning spaces for CHPS and LEED Schools:

EQ Prerequisite 3 - Minimum Acoustical Performance, OPTION 1. Using methods prescribed in ANSI S12.60, classrooms must achieve a maximum background noise level of 45 dBA.

I30H-I60H Indoor Sound Data at 10 Feet

ModelI30H I36H I42H I48H I60H

63.7 66.6 67.3 67.9 67.8

Outdoor Sound Data at 10 Feet

Vent: ERV IPBDFH-12 Duct Free 12" Plenum Box Ducted

Model Operation ERV Off ERV @ 150 ERV @ 375 ERV @ 450 ERV Off ERV @ 150 ERV @ 375 ERV @ 450

I30H Integrated 33.7 34.0 39.3 40.0 33.6 34.0 39.0 40.1

I36H Integrated 37.7 38.0 40.7 41.7 36.5 37.1 41.7 42.7

I42H Integrated 38.6 40.7 41.3 41.9 39.4 39.3 41.8 42.4

I48H Integrated 39.0 39.0 39.7 39.8 39.8 39.8 40.3 40.6

I60H Integrated 41.4 41.3 41.6 41.6 41.3 41.3 41.8 41.9

Vent: CRV IPBDFH-12 Duct Free 12" Plenum Box Ducted

Model Operation CRV Off CRV@ 300

CRV@ 375

CRV@ 450

CRV@ 525 CRV Off CRV

@ 300CRV

@ 375CRV

@ 450CRV

@ 525

I30H Integrated 34.4 36.0 38.2 40.6 42.1 34.6 36.6 38.1 40.6 42.0

I36H Integrated 37.0 38.5 40.3 42.4 43.9 37.2 40.2 39.2 42.2 44.0

I42H Integrated 39.2 39.8 41.0 42.5 43.5 39.9 40.4 41.1 42.8 43.5

I48H Integrated 40.2 40.7 41.5 43.0 44.2 41.0 40.7 42.2 43.4 44.1

I60H Integrated 44.0 44.3 44.6 45.4 45.9 43.5 43.7 44.1 44.8 45.5

Factory Setting(s) shaded in Gray

Page 20: I-TEC I30H-I60H 2-Stage Compressor High …...Form No S3451-918 SupersedesS3451-818 Page 4 of 20 Hot Water Coil Correction Factors Entering Air Temp (F) Entering Water Temperature

Form No S3451-918Supersedes S3451-818Page 20 of 20

Form No. S3451

September 2018

Supersedes: S3451-818

CompleteStat™ Selection Guide

Vent Type Type ofVent Control

BACnet Communication

Ethernet Connection

ControlCode Description CompleteStat

Part Number

NoneN/A Yes No 1 CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THOA

N/A Yes Yes 3 CompleteStat THO w/Ethernet CS9BE-THOA

CRV

On/Off Yes No 1 CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THOA

Demand Yes No 2 CompleteStat THO w/CO2 CS9B-THOCA

On/Off Yes Yes 3 CompleteStat THO w/Ethernet CS9BE-THOA

Demand Yes Yes 4 CompleteStat THO w/CO2 & Ethernet CS9BE-THOCA

ERV

On/Off Yes No 1 CompleteStat THO (Temp, Humidity & Occupancy) CS9B-THOA

Demand Yes No 2 CompleteStat THO w/CO2 CS9B-THOCA

On/Off Yes Yes 3 CompleteStat THO w/Ethernet CS9BE-THOA

Demand Yes Yes 4 CompleteStat THO w/CO2 & Ethernet CS9BE-THOCA

I-TEC 2-Stage Air Source Heat Pumps Model Number Nomenclature

I 36 H 1 D A 0Z R P 4 X X 2

Controls:X = 24v terminal block Only w/o Stat1 = CompleteStat THO (Temp, Humidity & Occupancy)2 = CompleteStat THO w/CO23 = CompleteStat THO w/ Ethernet4 = CompleteStat THO w/CO2 & EthernetNote: CompleteStat must be field installed & wired. All units have 24V terminal block. See Selection Guide.

Coil Treatment:X = Std. Hydrophilic Fin Evap. & Uncoated Alum. Cond. Coil1 = Phenolic Coated ID coil2 = Phenolic Coated OD coil3 = Phenolic Coated ID & OD coil

Color:X = Beige, Painted Steel1 = White, Painted Steel4 = Gray, Painted Steel

Filter:P = 2 inch pleated MERV 8M = 2 inch pleated MERV 11N = 2 inch pleated MERV 13

Vent Option:B = Blank Off PlateM = Multi-Speed CRVN = Multi-Speed CRV with Economizer ModeQ = Modulating CRV (0-10Vdc)R = ERV

Electric Heat:0Z = No heat w/Breaker04 = 4KW 1-Phase05 = 5KW 1-Phase06 = 6KW 3-Phase09 = 9KW 3-Phase10 = 10KW 1-Phase15 = 15KW 1 & 3-Phase18 = 18KW 3-Phase20 = 20KW 1-Phase

Electrical Rating:A = 230/208, 60-1B = 230/208, 60-3C = 460-60-3

Revision Level

System Type:H = Heat Pump

Nominal Capacity: 30 = 30,000 BTUH36 = 36,00042 = 42,00048 = 48,00060 = 60,000

Model Series

(-) = Standard (Non-Dehum)D = Dehumidification

Door Vinyl Graphics OptionsX = No GraphicsA = Stacked Books (Color Code 1 - White Only)B = Paint Brush (Color Code 1 - White Only)

Bard Manufacturing Company, Inc. Bryan, Ohio 43506 www.bardhvac.com

Due to our continuous product improvement policy, all specifications subject to change without notice. Before purchasing this appliance, read important energy cost and efficiency information available from your retailer.

BACnet is standard - all versions, shielded twisted pair.

These models also have CAT 5 port for ease of networking in addition to twisted pair terminals.

Demand control for ventilation is ON/OFF based on CO2 set-point.

If modulating mode for ERV is required, use – THO controller plus 8403-067 CO2 controller with modulating output.