Outline
, 2013Copyright Kohler China Ltd., 2013
1223272-T01-A
RECTANGULAR VESSEL/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
K-5373TFOREFRONT
ROUGHING-IN
( )
)( 13mm
Observe all local plumbing and buildingcodes.Inspect the waste and supply tubing;replace if necessary.Prior to installation, unpack the newlavatory and carefully inspect it fordamage. Return the lavatory to itsprotective carton until you are ready toinstall it.For replacement installations, make surethe existing cutout is the same or smallersize as the new lavatory.Use the template supplied with thelavatory to mark correct size cutout.Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings .Any other lavatory fittings may not fit forkohler lavatory.
Template(supplied)Safety glassesPencilScissorsTape measurePutty knifePlumbers puttyHacksawKeyhole saw or saber sawDrill (13mm or 1/2 dia. drill bit or larger)Adjustable wrenchPipe wrenchTubing cutter
TOOLS AND MATERIALS(Not Supplied)
BEFORE YOU BEGIN
13mm
REMOVE EXISTINGLAVATORY
INSTALL NEWLAVATORY
Turn off the water supply to the faucet.Open the faucet valves, then disconnect thesupply lines.Disconnect the drain assembly and removethe trap.Remove the existing lavatory.
Cut the template on the cutout line.Position the template on the countertop toensure clearance between the lavatory,faucet, and backsplash.Verify cabinet clearance beneath thecountertop.
Trace the template on the countertop with apencil.Re-check the clearance between thelavatory, faucet, backsplash, and cabinet.Adjust the template accordingly.
Drill a 13mm hole on the inside of thecutout opening.Cut the opening in the countertop along theinside edge of the pencil line.
Temporarily position the lavatory in theopening, and adjust to fit.
Large lavatories arevery heavy. Get help lifting the lavatoryinto place.
Trace a pencil line around the outside edgeof the lavatory.Remove the lavatory.Install the faucet and drain according to themanufacturers instructions.
Apply two beads of sealant to the inside ofthe pencil line.Spread the sealant evenly with a putty knife.
Carefully position the lavatory in the cutout,and press down firmly.
CAUTION: Risk of personal injury orproduct damage.
CAUTION: Risk ofpersonal injury or productdamage. Large lavatoriesare very heavy. Get helplifting the lavatory into place.
Immediately wipe away anyexcess sealant, and fill anyvoids as needed.Verify that the lavatory has notmoved out of position.Allow the sealant to cure for atleast 30 minutes beforeproceeding.Connect the faucet supply lines.Connect the drain assembly.Open the faucet valves, andcheck for leakage.Clean up with a non-abrasivecleaner.
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
0 Co
IMPORTANTCONSUMERINFORMATION (
Do not use the product in the water below0 C.o
CAREAND CLEANING)
To keep your lavatory looking new, makesure you rinse it out thoroughly after each
sihtno.esuproduct, as they will scratch and ruin thesurface. Stubborn stains, paint, or tar can beremoved with turpentine or paint thinner.
Please do not use hardmaterials (like scouring pad) to cleanproduct surface, especially theproduct logo.
DO NOT USE ABRASIVES
CAUTION:
500 mm
350 mm
368 mm
129 mm
Unit: mm:
575
410
562
390
82
175
1105685Overflow Cover
SERVICE PARTS
CUT ALONG THIS LINE
Kohler reserves the right to change marked dimensions without prior notice.
Reference Value
Length Width Height Depth
Outer
Inner
575 410
562 390
175
125