before you begin remove existing caution: risk of … · observe all local plumbing and building...

Outline , 2013 Copyright Kohler China Ltd., 2013 1223272-T01-A RECTANGULAR VESSEL / CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS K-5373T FOREFRONT ROUGHING-IN ( ) ) ( 13mm Observe all local plumbing and building codes. Inspect the waste and supply tubing; replace if necessary. Prior to installation, unpack the new lavatory and carefully inspect it for damage. Return the lavatory to its protective carton until you are ready to install it. For replacement installations, make sure the existing cutout is the same or smaller size as the new lavatory. Use the template supplied with the lavatory to mark correct size cutout. Kohler lavatory is made according to American National Standard that it can match the American lavatory fittings . Any other lavatory fittings may not fit for kohler lavatory. Template(supplied) Safety glasses Pencil Scissors Tape measure Putty knife Plumbers putty Hacksaw Keyhole saw or saber saw Drill (13mm or 1/2 dia. drill bit or larger) Adjustable wrench Pipe wrench Tubing cutter TOOLS AND MATERIALS (Not Supplied) BEFORE YOU BEGIN 13mm REMOVE EXISTING LAVATORY INSTALL NEW LAVATORY Turn off the water supply to the faucet. Open the faucet valves, then disconnect the supply lines. Disconnect the drain assembly and remove the trap. Remove the existing lavatory. Cut the template on the cutout line. Position the template on the countertop to ensure clearance between the lavatory, faucet, and backsplash. Verify cabinet clearance beneath the countertop. Trace the template on the countertop with a pencil. Re-check the clearance between the lavatory, faucet, backsplash, and cabinet. Adjust the template accordingly. Drill a 13mm hole on the inside of the cutout opening. Cut the opening in the countertop along the inside edge of the pencil line. Temporarily position the lavatory in the opening, and adjust to fit. Large lavatories are very heavy. Get help lifting the lavatory into place. Trace a pencil line around the outside edge of the lavatory. Remove the lavatory. Install the faucet and drain according to the manufacturers instructions. Apply two beads of sealant to the inside of the pencil line. Spread the sealant evenly with a putty knife. Carefully position the lavatory in the cutout, and press down firmly. CAUTION: Risk of personal injury or product damage. CAUTION: Risk of personal injury or product damage. Large lavatories are very heavy. Get help lifting the lavatory into place. Immediately wipe away any excess sealant, and fill any voids as needed. Verify that the lavatory has not moved out of position. Allow the sealant to cure for at least 30 minutes before proceeding. Connect the faucet supply lines. Connect the drain assembly. Open the faucet valves, and check for leakage. Clean up with a non-abrasive cleaner. Faucet Supply Lines Shut-off Valve Drain Assembly 0C o IMPORTANT CONSUMER INFORMATION ( Do not use the product in the water below 0 C. o CARE AND CLEANING) To keep your lavatory looking new, make sure you rinse it out thoroughly after each s i h t n o . e s u product, as they will scratch and ruin the surface. Stubborn stains, paint, or tar can be removed with turpentine or paint thinner. Please do not use hard materials (like scouring pad) to clean product surface, especially the product logo. DO NOT USE ABRASIVES CAUTION: 500 mm 350 mm 368 mm 129 mm Unit: mm : 575 410 562 390 82 175 1105685 Overflow Cover SERVICE PARTS CUT ALONG THIS LINE Kohler reserves the right to change marked dimensions without prior notice. Reference Value Length Width Height Depth Outer Inner 575 410 562 390 175 125

Upload: others

Post on 18-Aug-2020

1 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: BEFORE YOU BEGIN REMOVE EXISTING CAUTION: Risk of … · Observe all local plumbing and building codes. Inspect the waste and supply tubing; replace if necessary. Prior to installation,

Outline

, 2013Copyright Kohler China Ltd., 2013

1223272-T01-A

RECTANGULAR VESSEL/

CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS

K-5373TFOREFRONT

ROUGHING-IN

( )

)( 13mm

Observe all local plumbing and buildingcodes.Inspect the waste and supply tubing;replace if necessary.Prior to installation, unpack the newlavatory and carefully inspect it fordamage. Return the lavatory to itsprotective carton until you are ready toinstall it.For replacement installations, make surethe existing cutout is the same or smallersize as the new lavatory.Use the template supplied with thelavatory to mark correct size cutout.Kohler lavatory is made according toAmerican National Standard that it canmatch the American lavatory fittings .Any other lavatory fittings may not fit forkohler lavatory.

Template(supplied)Safety glassesPencilScissorsTape measurePutty knifePlumbers puttyHacksawKeyhole saw or saber sawDrill (13mm or 1/2 dia. drill bit or larger)Adjustable wrenchPipe wrenchTubing cutter

TOOLS AND MATERIALS(Not Supplied)

BEFORE YOU BEGIN

13mm

REMOVE EXISTINGLAVATORY

INSTALL NEWLAVATORY

Turn off the water supply to the faucet.Open the faucet valves, then disconnect thesupply lines.Disconnect the drain assembly and removethe trap.Remove the existing lavatory.

Cut the template on the cutout line.Position the template on the countertop toensure clearance between the lavatory,faucet, and backsplash.Verify cabinet clearance beneath thecountertop.

Trace the template on the countertop with apencil.Re-check the clearance between thelavatory, faucet, backsplash, and cabinet.Adjust the template accordingly.

Drill a 13mm hole on the inside of thecutout opening.Cut the opening in the countertop along theinside edge of the pencil line.

Temporarily position the lavatory in theopening, and adjust to fit.

Large lavatories arevery heavy. Get help lifting the lavatoryinto place.

Trace a pencil line around the outside edgeof the lavatory.Remove the lavatory.Install the faucet and drain according to themanufacturers instructions.

Apply two beads of sealant to the inside ofthe pencil line.Spread the sealant evenly with a putty knife.

Carefully position the lavatory in the cutout,and press down firmly.

CAUTION: Risk of personal injury orproduct damage.

CAUTION: Risk ofpersonal injury or productdamage. Large lavatoriesare very heavy. Get helplifting the lavatory into place.

Immediately wipe away anyexcess sealant, and fill anyvoids as needed.Verify that the lavatory has notmoved out of position.Allow the sealant to cure for atleast 30 minutes beforeproceeding.Connect the faucet supply lines.Connect the drain assembly.Open the faucet valves, andcheck for leakage.Clean up with a non-abrasivecleaner.

Faucet

Supply Lines

Shut-off Valve

Drain Assembly

0 Co

IMPORTANTCONSUMERINFORMATION (

Do not use the product in the water below0 C.o

CAREAND CLEANING)

To keep your lavatory looking new, makesure you rinse it out thoroughly after each

sihtno.esuproduct, as they will scratch and ruin thesurface. Stubborn stains, paint, or tar can beremoved with turpentine or paint thinner.

Please do not use hardmaterials (like scouring pad) to cleanproduct surface, especially theproduct logo.

DO NOT USE ABRASIVES