Date: 1 October 2018

To: All Planholders

Subject: ADDENDUM NO. 4

Project: RENOVATION TO THE

STUDENT CENTER GRILL AREA

INTO A CULINARY ARTS FACILITY

Job #: SSL# 18002

DCM# 2018163

From: Jacob Johnson

The plans and Specifications of the subject project, dated AUG 2018 are amended as

follows: (Where there are conflicts between the plans and specifications and the

addendum, this addendum shall govern)

Item No. 1: Refer to drawings. Delete Architectural sheet A7.2 and replace it with the

attached Architectural sheet A7.2 dated 10-1-2018.

Item No. 2: Refer to drawings. Delete Plumbing sheet P1.1 and replace it with the

attached Plumbing sheet P1.1 dated 10-1-2018.

Item No. 3: Refer to specification section 08 3313 “Coiling Counter Shutter.” Replace

with the attached specification section 08 3313 “Coiling Counter Shutter”

dated 10-1-2018.

Item No. 4: Refer to Specification section 10 1400 “Signage.” Replace with the

attached Specification Section 101400 “Signage” dated 10-1-2018.

End of Addendum #4

Attachments

A7.2

P1.1

Specification 08 3313

Specification 10 1400

HEAD DETAIL

FIBERGLASS REINFORCED PANEL

GYPSUM WALLBOARD

METAL STUD FRAMING

FRP MANUFACTURER'S

CORNER TRIM

WALL BEYOND

STAINLESS STEEL COUNTERTOP & EDGE

MDF BOARD

FRP MANUFACTURER'S END TRIM

FIBERGLASS REINFORCED PANEL

(BOTH SIDES)

GYPSUM WALLBOARD (BOTH SIDES)

METAL STUD FRAMING

SILL DETAIL

STAINLESS STEEL COUNTERTOP

FRP MANUFACTURER'S CORNER TRIM

FIBERGLASS REINFORCED PANEL (BOTH SIDES)

METAL STUD FRAMING

GYPSUM WALLBOARD (BOTH SIDES)

JAMB DETAIL

PROVIDE STUDWORK NECESSARY

FOR HOOD

SQUARE HOOD - SIZE AS

REQUIRED BY MANUFACTURER

FIBERGLASS REINFORCED PANEL

12" MIN.

CEILING - SEE REFLECTED CEILING PLAN

GYPSUM WALLBOARD

BATT INSULATION

METAL STUD FRAMING

STENSIL WORDS: "DO NOT USE FOR

STORAGE"

METAL STUD FRAMING AS REQ.

1" SHAFTLINER

FIBERGLASS REINFORCED PANEL

GYPSUM WALLBOARD

GYPSUM WALLBOARD

DOOR BEYOND

HIGH IMPACT GYPSUM WALLBOARD

WALL BASE - SEE FINISH SCHEDULE

PROVIDE CONCEALED CONTINUOUS

WEED BLOCKING AT METAL STUD WALLS

FOR CRASH RAIL. (TYP.)

GYPSUM BEYOND

CEILING - SEE REFLECTED CEILING PLAN

LINE OF BULKHEAD (NOT IN VIEW)

ACOUSTIC WALL PANEL

PARGE COAT

ACOUSTIC WALL PANEL MANUFACTURER'S

END TRIM

CRASH RAIL

ACOUSTIC WALL PANEL

ACOUSTIC WALL PANEL MANUFACTURER'S END TRIM

GYPSUM WALLBOARD

METAL STUD FRAMING

EXISTING MASONRY WALL

PARGE COAT

NOTE: ADD CONCEALED CONTINUOUS WOOD BLOCKING FOR

CRASH RAILS ON NEW METAL STUD WALLS. SEE 4/A7.2

SEE SPEC SECTION 10 1400 FOR

SIGNAGE MATERIAL AND FINISH

REQUIREMENTS

1' -

0"

0' -

3"

0' -

6"

PROVIDE CONCEALED WOOD BLOCKING FOR

ATTACHMENT OF LETTERING AND MASCOT SIGNAGE

(IF ALTERNATE IS NOT ACCEPTED, OMIT THIS DRAWING

2

ADD #2

114 3/4"

48

3/4

"

4

ADD #4

4

ADD #4

ACOUSTIC WALL PANEL

MANUFACTURER'S MID-WALL REVEAL

ACOUSTIC WALL PANEL

EXISTING MASONRY WALL TO REMAIN

PAINT EXISTING CMU WALL

BEHIND PANELS (TYP.)

ACOUSTIC WALL PANEL

MANUFACTURER'S END TRIM

ACOUSTIC WALL PANEL

GYPSUM WALLBOARD

EXISTING MASONRY WALL

METAL STUD FRAMING

METAL STUD FRAMING AS REQ.

GYPSUM WALLBOARD

ACOUSTIC INFILL

PROVIDED BY CEILING

MANUFACTURER.

UNIVERSAL CARRIER BY

CEILING MANUFACTURER

CEILING - SEE FINISH SCHEDULE

MANUFACTURER'S J-TRIM

FIELD CUT PANEL END AS REQUIRED TO FIT.

12

" M

AX P

ANEL

OVERHANG

TYP.

12" MAX PANEL

OVERHANG TYP.

CARRIER SPACING TYP.

48" MAX O.C.

3/1

6"

2 1/8"

TILE BASE - SEE FINISH

SCHEDULE

ADJUSTABLE SHELVES -TYP.

PLASTIC LAMINATE

BLOCKING / REINFORCED

GLASS FIBER GYP. BOARD

3/4" MARINE GRADE PLYWOOD

W/ INTERIOR CABINET LINER -

SEE SPECIFICATION SECTION

06 4100

2' - 0"

HARDWOOD NOSING SUBSTRATE

16 GUAGE STAINLESS STEEL

COUNTER TOP W/ BULLNOSE EDGE

& 4" HIGH BACK SPLASH. MATCH

AS SHOWN ON SHEET QF200 &

QF500.

3/4" MARINE GRADE PLYWOOD

2' -

10

"

2' - 1"

REINFORCED GLASS FIBER GYP. BOARD-

SEE FINISH SCHEDULE

8' - 1"

2' - 8" 2' - 9" 2' - 8"

1' - 2 7/8" 1' - 2 7/8" 1' - 3 3/8" 1' - 3 3/8" 1' - 2 7/8" 1' - 2 7/8"

4"

2' -

0 3

/4"

TYP.

3/4

"

2

A7.2

Sim

___________

4"

CABINET LOCK - SEE SPECS

Sheet Number

Sheet Title

Project Title

Job Number

Date

Drawn By

Checked By

1115

So

uth

Co

urt

Str

eet

| M

on

tgo

mer

y, A

L 3

6104

Tel

. 334

. 263.

516

2 |

WWW.SSLARCH.COM

AR

CH

ITE

CT

UR

E &

IN

TE

RIO

R D

ESIG

N

A7.2

INTERIORELEVATIONS& SECTIONS

CU

LIN

AR

Y A

RT

S -

WO

OD

Y'S

GR

ILL

WSC

C H

AN

CE

VIL

LE

, AL

18002

AUG 2018

JJ/CF

DCD

3" = 1'-0"A7.2

1 PASS-THROUGH WINDOW

1" = 1'-0"A7.2

4 Section 5

3" = 1'-0"A7.2

8 CRASH RAIL DETAIL3/4" = 1'-0"A7.2

9 WALLACE STATE LOBBY LOGO

3" = 1'-0"A7.2

5 ACOUSTIC WALL PANEL REVEAL DETAIL

3" = 1'-0"A7.2

6 ACOUSTIC WALL PANEL CORNER DETAIL

3" = 1'-0"A7.2

7 CEILING INTERIOR CORNER TRANSITION DETAIL

1 1/2" = 1'-0"A7.2

2 CASEWORK SECTION

1" = 1'-0"A7.2

3 CASEWORK ELEVATION

No. Revision Date

2 ADD #2 9-14-18

4 ADD #4 10-1-18

MONTGOMERY, AL. 36104800 S McDONOUGH STREET

334.263.4406

ZGOUVAS, EIRING & ASSOCIATESCONSULTING ENGINEERS

ZEA PROJECT NUMBER 18-47

Sheet Number

Sheet Title

Project Title

Job Number

Date

Drawn By

Checked By

1115 S

outh

Co

urt

Str

eet

| M

on

tgo

mer

y, A

L 3

6104

Tel

. 334. 263. 5162 |

WW

W.S

SL

AR

CH

.CO

M

AR

CH

ITE

CT

UR

E &

IN

TE

RIO

R D

ESIG

N

CU

LIN

AR

Y A

RT

S -

WO

OD

Y'S

GR

ILL

WSC

C H

AN

CE

VIL

LE

, A

L

18002

CW

No. Revision Date

P1.1

8-21-18

JE

August, 2018

2 Add. #2 9-14-18

4 Add. #4 10-1-18

PLBG. SCHED.,DETAILS ANDRISER

2

4

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

COILING COUNTER DOORS 08 3313 - 1

SECTION 08 3313 - COILING COUNTER DOORS

PART 1 GENERAL

1.01 SECTION INCLUDESA. Fire-rated coiling counter doors and operating hardware (refer to door schedule).

1.02 RELATED REQUIREMENTSA. Section 06 1000 - Rough Carpentry: Rough openings.B. Section 07 9005 - Joint SealersC. Section 09 2116 - Gypsum Board Assemblies: Rough openings.D. Division 26 - Electrical

1.03 REFERENCE STANDARDSA. ASTM A36/A36M - Standard Specification for Carbon Structural Steel; 2014.B. ASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings

on Iron and Steel Products; 2015.C. ASTM A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated

(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process; 2015.D. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded

Bars, Rods, Wire, Profiles, and Tubes; 2014.E. ASTM B221M - Standard Specification for Aluminum and Aluminum-Alloy Extruded

Bars, Rods, Wire, Profiles, and Tubes [Metric]; 2013.F. ITS (DIR) - Directory of Listed Products; current edition.G. NFPA 80 - Standard for Fire Doors and Other Opening Protectives; 2016.H. UL (BMD) - Building Materials Directory; Underwriters Laboratories Inc.; current

edition.

1.04 SUBMITTALSA. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Submit manufacturer's standard literature showing materials and details

of construction and finish. C. Shop Drawings: Indicate rough and actual opening dimensions, anchorage methods,

hardware locations, and installation details.D. Samples: Submit two slats, 4 inches long illustrating shape, color and finish texture.

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

COILING COUNTER DOORS 08 3313 - 2

E. Manufacturer's Instructions: Indicate installation sequence and installation, adjustment,and alignment procedures.

F. Operation and Maintenance Data: Indicate modes of operation, lubricationrequirements and frequency, and periodic adjustments required.

G. Project Record Documents: Include as-built electrical diagrams for electrical operationand connection to fire alarm system.

PART 2 PRODUCTS

2.01 BASIS OF DESIGNA. Coiling Counter Doors:

1. Overhead Door Model 640.2. McKeon Door Auto-Set CFS Series3. Substitutions: See Section 01 6000 - Product Requirements.

2.02 COILING COUNTER DOORSA. Coiling Counter Doors, Fire-Rated: Galvanized steel slat curtain.

1. Mounting: As indicated.2. Fire Rating: As indicated on the drawings; comply with NFPA 80.

a. Provide product listed and labeled by UL or ITS (Warnock Hersey) as suitablefor the purpose specified and indicated.

3. Nominal Slat Size: 1-1/4 inches wide.4. Slat Profile: Flat.5. Finish: factory baked enamel - polyester top coat.6. Color: As selected by Architect from manufacturer's standard colors.7. Guides: Formed track; same material and finish unless otherwise indicated.8. Hood: Manufacturer's standard, equipped with thermally controlled, internal,

galvanized steel flame baffle as required for FM listing.9. Fire Release Mechanisms:

a. Automatically self-closing with governed closing speed.b. Provide manufacturer's standard fusible link (165 degree rated).c. Provide release device and all wiring/accessories required to also connect door

to building fire alarm system to active self closing of door upon actuation ofthe building fire alarm system.

d. Release device shall have an integral battery backup providing a minimum of24 hours of backup power to hold the door in the open position in the event ofpower failure. Battery back must have override capability so that an alarmevent during a power failure will override the device and initiate self closingprocedure of door.1) Release device to be equal to LiftMaster model LN21XPBB

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

COILING COUNTER DOORS 08 3313 - 3

10. Non-Fire Operation: Manual hand chain lift.11. Interior latch only.12. Warranty: Manufacturer's standard 2 year warranty.

2.03 MATERIALSA. Curtain Construction: Interlocking, single thickness slats.

1. Slat Ends: Alternate slats fitted with end locks to act as wearing surface in guidesand to prevent lateral movement.

2. Curtain Bottom: Fitted with angles to provide reinforcement and positive contactin closed position.

3. Steel Slats: ASTM A653/A653M galvanized steel sheet, with minimumG90/Z275 coating; minimum thickness 22 gage, 0.03 inch.

B. Guide Construction: Continuous, of profile to retain door in place, with mountingbrackets of same metal.

C. Latching: Inside mounted, sliding deadbolt.D. Roller Shaft Counterbalance: Steel pipe and torsion steel spring system, capable of

producing torque sufficient to ensure smooth operation of curtain from any position andcapable of holding position at mid-travel; with adjustable spring tension; requiring 25 lbnominal force to operate.

PART 3 EXECUTION

3.01 EXAMINATIONA. Verify that opening sizes, tolerances and conditions are acceptable.

3.02 INSTALLATIONA. Install units in accordance with manufacturer's instructions.B. In addition, install fire-rated doors in accordance with NFPA 80.C. Use anchorage devices to securely fasten assembly to wall construction and building

framing without distortion or stress.D. Securely and rigidly brace components suspended from structure. Secure guides to

structural members only.E. Fit and align assembly including hardware; level and plumb, to provide smooth

operation.F. Coordinate installation of electrical components in accordance with applicable sections

of Division 26.G. Complete wiring from fire alarm system .

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

COILING COUNTER DOORS 08 3313 - 4

H. Install perimeter trim as indicated.

3.03 TOLERANCESA. Maintain dimensional tolerances and alignment with adjacent work.B. Maximum Variation From Plumb: 1/16 inch.C. Maximum Variation From Level: 1/16 inch.D. Longitudinal or Diagonal Warp: Plus or minus 1/8 inch per 10 ft straight edge.

3.04 ADJUSTINGA. Adjust operating assemblies for smooth and noiseless operation.

3.05 CLEANINGA. Clean installed components.B. Remove labels and visible markings.

END OF SECTION

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

SIGNAGE 10 1400 - 1

SECTION 10 1400 - SIGNAGE

PART 1 GENERAL

1.01 SECTION INCLUDESA. Updateable curved aluminum frame system signB. Dimensional LettersC. Vinyl Window Lettering.D. Metal Plaques

1.02 RELATED REQUIREMENTSA. Section 09 9123 Interior Painting

1.03 REFERENCE STANDARDSA. 36 CFR 1191 - Americans with Disabilities Act (ADA) Accessibility Guidelines for

Buildings and Facilities; Architectural Barriers Act (ABA) Accessibility Guidelines;current edition.

B. ADA Standards - Americans with Disabilities Act (ADA) Standards for AccessibleDesign; 2010.

C. ICC A117.1 - Accessible and Usable Buildings and Facilities; 2009.

1.04 SUBMITTALSA. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Manufacturer's printed product literature for each type of sign, indicating

sign styles, font, foreground and background colors, locations, overall dimensions ofeach sign.

C. Signage Schedule: Provide information sufficient to completely define each sign forfabrication, including room number, room name, other text to be applied, sign and lettersizes, fonts, and colors.1. When room numbers to appear on signs differ from those on drawings, include the

drawing room number on schedule.2. When content of signs is indicated to be determined later, request such information

from Owner through Architect at least 2 months prior to start of fabrication; uponrequest, submit preliminary schedule.

3. Submit for approval by Owner through Architect prior to fabrication.

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

SIGNAGE 10 1400 - 2

D. Evidence of Manufacturer's computerized data retrieval system for tracking of projectfor sign typography, message strip requirements ad otehr pertinent data from scheduleinput to final computerized typography on finished product.

E. Samples: Submit one sample of each type of sign, of size similar to that required forproject, illustrating sign style, font, and method of attachment. Sample will be returnedfor use in the project.

F. Selection Samples: Where colors are not specified, submit two sets of color selectioncharts or chips.

G. Manufacturer's Installation Instructions: Include installation templates and attachmentdevices.

H. Maintenance Materials: Furnish the following for Owner's use in maintenance ofproject.1. See Section 01 6000 - Product Requirements, for additional provisions.

1.05 QUALITY ASSURANCEA. Manufacturer Qualifications: Company specializing in manufacturing the products

specified in this section with minimum three years of documented experience.B. All metal letters and plaques to be manufactured by the same Manufacturer.

1.06 DELIVERY, STORAGE, AND HANDLINGA. Package signs as required to prevent damage before installation.B. Package room and door signs in sequential order of installation, labeled by floor or

building.

PART 2 PRODUCTS

2.01 MANUFACTURERSA. Curved Face Signs: (Room Signs)

1. Basis-of-design: Apco Signs; www.apcosigns.com.Arcadia Series. Submit shopdrawings for types, locations and approval.

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

SIGNAGE 10 1400 - 3

apco2. Signage shall have updatability feature: Signs shall allow for easy updating of

message inserts without the need to replace the entire sign assembly.3. Substitutions: See Section 01 6000 - Product Requirements.

B. Dimensional Letter Signs:1. Apco Signs; www.apcosigns.com. Basis of Design is Apco Flat Cut Fabricated,

Reverse Channel with open back Metal Letters2. Leeds Architectural Letters; www.leedsletter.com.3. Impact Signs, Inc.; www.impactsigns.com.4. Substitutions: See Section 01 6000 - Product Requirements.5. Finish of Metal Letters to meet ASTM G4A specifications.

2.02 SIGNAGE APPLICATIONSA. Accessibility Compliance: Signs are required to comply with ADA Standards and ICC

A117.1, unless otherwise indicated; in the event of conflicting requirements, complywith the most comprehensive and specific requirements.

B. Room Signs: Provide a sign only for the following areas- Dishwashing, DryStorage, Pastry Lab, Savory Lab, and Dining Room.1. Provide "tactile" signage, with letters raised minimum 1/32 inch and Grade II

braille.2. Character Height: 5/8 inch3. Sign Height: 3 inches4. Typeset: Frutiger-Normal5. Provide glass backers for signage placed on glass

C. Vinyl Window Lettering to Identify the following rooms only: Savory Lab andPastry Lab1. Peel and Stick type2. Color to be selected from Manufacturer's Full Range.3. Lettering and color to be defined by owner and submitted for approval.4. Character Height: 3 inches5. Typeset: Frutiger-Normal

2.03 PLAQUESA. Metal: 1/4" thick, 6061 Aluminum AlloyB. Finish:

1. 0.7 mil thick clear anodized process complying with AA-M33-C22-A31C. Fabrication: laser or water jet cut process as recommended by manufactuer for plaque.

Provide 1-1/2 inch return on all edges of plaque. Finish return to match face of plaque.D. Mounting: Concealed screws with metal spacers as required to project lettering 2-1/2

inches off of finished wall.

A New Culinary Arts Facility 18002.00 August 2018Wallace State Community College, Hanceville, AL 100% Specifications

Revised 10-1-18

SIGNAGE 10 1400 - 4

2.04 DIMENSIONAL LETTERSA. Metal: 1/4" thick, 6061 Aluminum Alloy 1/8" thick Stainless SteelB. Finish: Brushed Hairline

1. 0.7 mil thick clear anodized process complying with AA-M33-C22-A31C. Fabrication: laser or water jet cut process as recommended by manufactuer for lettering

intended to be installed. Provide 1-1/2 inch return on all side of each letter. Finishreturn to match face of lettering.

D. Size & Type Face: As indicated on the drawings.E. Mounting: Concealed screws with metal spacers as required to project lettering 2-1/2

inches off of finished wall.

2.05 ACCESSORIES

PART 3 EXECUTION

3.01 EXAMINATIONA. Verify that substrate surfaces are ready to receive work.

3.02 INSTALLATIONA. Install in accordance with manufacturer's instructions.B. Install neatly, with horizontal edges level.C. Locate signs and mount at heights indicated on drawings and in accordance with ADA

Standards and ICC A117.1.D. Protect from damage until Substantial Completion; repair or replace damaged items.E. Verify that concealed wood blocking has been placed prior to installation of metal

letters and plaques scheduled to be installed in metal stud framed walls.

3.03 WARRANTYA. Metal Letters should be guaranteed for the life of the business against defects.B. Product warranty: Provide manufacturer's warranty against defects in materials and

workmanship for a period of one year.

END OF SECTION