cfx12 b turbo
TRANSCRIPT
-
7/28/2019 Cfx12 b Turbo
1/26
Appendix B
Turbo Pre and Post
B-1ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
Introduction to CFX
-
7/28/2019 Cfx12 b Turbo
2/26
Turbo Pre
B-2ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
-
7/28/2019 Cfx12 b Turbo
3/26
Turbo Pre and Post
Training Manual
Turbo mode in ANSYS CFX-Pre is a specialist mode
allowing users to set up turbo machinery simulations,such as compressors or turbines, in a simple manner.
CFX-Pre Turbo Mode
B-3ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
-
7/28/2019 Cfx12 b Turbo
4/26
Turbo Pre and Post
Training ManualCFX-Pre Turbo Mode
At any time, users can enter turbo mode from the filemenu
Tools > Turbo Mode
Buttons at bottom to navigate through the wizard:
Next move to the next page
Back move to the revious a e
B-4ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
Finish any data that has been entered will becommitted, Pre goes into General Mode
Cancel close Turbo mode and revert to General Mode Meshes will remain, data will not
-
7/28/2019 Cfx12 b Turbo
5/26
Turbo Pre and Post
Training Manual
1. Basic Settings
setup axis of rotation and coordinate frame
CFX-Pre Turbo Mode
B-5ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
-
7/28/2019 Cfx12 b Turbo
6/26
Turbo Pre and Post
Training Manual
2. Component Definition
Import meshes (right-click)
Define rotating or stationary
Define rotational speed
Define number of passages
CFX-Pre Turbo Mode
B-6ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
e ne t p c earanceapplicable
For multiple stages, use right
click to:
Change component order Automatically align components
-
7/28/2019 Cfx12 b Turbo
7/26
Turbo Pre and Post
Training Manual
3. Physics Definition
Fluid properties
Steady State vs. Transient Model Data
Energy and Turbulence Models
Boundar Tem lates:
CFX-Pre Turbo Mode
B-7ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
Pt inlet - Ps outlet Pt inlet - mass flow outlet
Mass flow inlet Ps outlet
Interface Type:
Stage, Frozen Rotor, Transient Rotor Stator Solver parameters
Advection Scheme
Time Scale/Step controls
-
7/28/2019 Cfx12 b Turbo
8/26
Turbo Pre and Post
Training Manual
4. Interface Definition
Domain interfaces
automatically generated!
Setup/check all Domain
Interfaces
CFX-Pre Turbo Mode
B-8ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
Transient rotor stator
Stage
Periodic
None
Right-click to add or deleteinterfaces
-
7/28/2019 Cfx12 b Turbo
9/26
Turbo Pre and Post
Training Manual
5. Boundary Definition
Boundary regions and
conditions automaticallysetup!
Define/check boundary
CFX-Pre Turbo Mode
B-9ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved. April 28, 2009Inventory #002598
Right-click to add or removeboundary conditions
-
7/28/2019 Cfx12 b Turbo
10/26
Turbo Pre and Post
Training Manual
6. Final Operations
Options:
Enter General Mode tomake further operations
Ex. Create monitor points
Ex. Setup a multi-
CFX-Pre Turbo Mode
B-10ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002598
configuration run
Write .def file and start thesolver
Option to quit CFX Pre
-
7/28/2019 Cfx12 b Turbo
11/26
Turbo Pre and Post
Training Manual
Summary six steps to setup a turbomachinerysimulation:
1. Basic Settings
2. Component Definition
3. Physics Definition
4. Interface Definition
CFX-Pre Turbo Mode
B-11ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002598
5. Boundary Definition6. Final Operation
Advantages: Rapid setup for turbomachinery simulations
Automatic creation of domain interfaces and boundary definitions
-
7/28/2019 Cfx12 b Turbo
12/26
Turbo Pre and Post
Training Manual
After the case has been set up in Turbo Mode, thefollowing modifications can be made in general
mode: Component mesh or case reload
One to One connections for periodic and stationary
CFX-Pre General Mode
B-12ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002598
Domain interface intersection control
Creation of monitor points and/or source points
Multi-configuration simulation
Execution control
-
7/28/2019 Cfx12 b Turbo
13/26
Turbo Post
B-13ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002598
-
7/28/2019 Cfx12 b Turbo
14/26
Turbo Pre and Post
Training Manual
The Turbo workspace improves and speeds up post-processing for turbo machinery simulations
All Turbo post-
CFD-Post Turbo Workspace
B-14ANSYS, Inc. Proprietary 2009 ANSYS, Inc. All rights reserved.
April 28, 2009Inventory #002598
performed on theTurbo tab
-
7/28/2019 Cfx12 b Turbo
15/26
Turbo Pre and Post
Training Manual
The Turbo workspace:
Creates span, m, axial, radial and theta coordinate frames
Allows users to visualize components in turbo space
One-button calculation of velocity components (such ascircumferential, radial, axial, meridional)
Quickly generate turbo related charts and graphs
Provides access to turbo s ecific macros
CFD-Post Turbo Workspace
B-15ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.April 28, 2009
Inventory #002598
Works with Fluent or CFX results
-
7/28/2019 Cfx12 b Turbo
16/26
Turbo Pre and Post
Training Manual
Initialization
Input required to create backgroundmesh
Specify number of instances tovisualize full geometry
Options
CFD-Post Turbo Workspace
B-16ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Manual Initialization
User selects hub, shroud, blade, inlet,outlet, and periodic surfaces
Calculate Velocity Components
Ex. Radial, Tangential, andMeridional velocity components
-
7/28/2019 Cfx12 b Turbo
17/26
Turbo Pre and Post
Training Manual
Background Mesh
Necessary to calculatestreamwise (m) and spanwise
coordinates 2D mesh formed by collapsing
hub, shroud, inlet and outlet onto an axial-radial plane
CFD-Post Turbo Workspace
B-17ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
ut ne s e w t mesconsisting of constant span andm lines
-
7/28/2019 Cfx12 b Turbo
18/26
Turbo Pre and Post
Training Manual
Four types of objects are available that are useful forturbo machinery applications
3D View
Blade-to-Blade
Meridional
Turbo Charts
CFD-Post Turbo Workspace
B-18ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
-
7/28/2019 Cfx12 b Turbo
19/26
Turbo Pre and Post
Training Manual
3D View Plot
Can select which parts to draw
Optionally with mesh lines
Show Blade-to-Blade plot in 3D view
Show chart location lines
Instancin
CFD-Post Turbo Workspace
B-19ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
-
7/28/2019 Cfx12 b Turbo
20/26
Turbo Pre and Post
Training Manual
Blade-to-Blade Plot
Select Span
Can generate thefollowing plots:
Colour
Contour
CFD-Post Turbo Workspace
B-20
ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Vector
Streamlines
-
7/28/2019 Cfx12 b Turbo
21/26
-
7/28/2019 Cfx12 b Turbo
22/26
Turbo Pre and Post
Training Manual
Turbo Chart
Select one of the followingchart types:
Blade Loading Circumferential
Hub to Shroud
Inlet to Outlet
CFD-Post Turbo Workspace
B-22
ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Based on the chart type, usermany need to input:
X and Y axes variables
Spanwise and/or streamwiselocation
Number and distribution ofsampling points
Select the type of circumferentialaveraging
-
7/28/2019 Cfx12 b Turbo
23/26
Turbo Pre and Post
Training Manual
Turbo Macros
Four predefined macros
Fan Noise
Gas CompressorPerformance
Gas Turbine Performance
Li uid Turbine Performance
CFD-Post Turbo Workspace
B-23
ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Pump Performance Modify input requirements
as necessary
Generates a report in .html
format Calculates relevant
quantitative data
-
7/28/2019 Cfx12 b Turbo
24/26
-
7/28/2019 Cfx12 b Turbo
25/26
Turbo Pre and Post
Training Manual
Turbo Post
Automated initialization of components
All turbo post objects are presented in a single encapsulatedinterface
Turbo Post graphical objects can be promoted to full postprocessing mode for general use if desired
CFD-Post Turbo Workspace
B-25
ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Additional Tools in CFD Post Tables can be created
Multiple cases can be loaded and compared
Generation of performance curves
Turbo Surfaces and Turbo Lines can be created in GeneralMode
-
7/28/2019 Cfx12 b Turbo
26/26
Turbo Pre and Post
Training Manual
Turbo-Pre
Facilitates setup of rotating machinery problems
Turbo-Post Provides additional functionality in CFD-Post to add powerful
post-processing capabilities for turbo cases
Key Point
B-26
ANSYS, Inc. Proprietary
2009 ANSYS, Inc. All rights reserved.
April 28, 2009
Inventory #002598
Axial Fan Workshop
Tutorial # 12