BBU 3900 instation Guide

Download BBU 3900 instation Guide

Post on 16-Apr-2015

328 views

Category:

Documents

24 download

Embed Size (px)

DESCRIPTION

Safety Information 1. Information About the Installation 2. Installing the BBU in the APM30 3. Installing the BBU in the APM30H4. Installing the BBU in the APM30 (+24 V)5. Installing the BBU in the 19-Inch Cabinet 6. Installing the BBU on the Wall7. Installing the BBU in the PS4890 Cabinet 8. Installing the BBU in the OMB Cabinet 9. Installing the BBU in the TMC 10. Installing the BBU in the TMC11H11. Checking the Power-On Status of the BBU 12. Reference

TRANSCRIPT

BBU3900 V200

Installation Guide

Issue: 05 Part Number: 31504449 Date: 2009-03-05HUAWEI TECHNOLOGIES CO., LTD.

Content

Safety Information 1. Information About the Installation 2. Installing the BBU in the APM30 3. Installing the BBU in the APM30H 4. Installing the BBU in the APM30 (+24 V) 5. Installing the BBU in the 19-Inch Cabinet 6. Installing the BBU on the Wall 7. Installing the BBU in the PS4890 Cabinet 8. Installing the BBU in the OMB Cabinet 9. Installing the BBU in the TMC 10. Installing the BBU in the TMC11H 11. Checking the Power-On Status of the BBU 12. Reference

2 3 8 15 17 19 23 28 33 39 41 42 43

1

Safety InformationFollowing All Safety PrecautionsBefore any operation, read the instructions and precautions in this document carefully to minimize the possibility of accidents. The Danger, Caution, and Note items in the documents do not cover all the safety precautions that must be followed. They only provide the generic safety precautions for operations. When operating Huawei products and equipment, you must comply with safety precautions and special safety instructions related to corresponding equipment provided by Huawei. The safety precautions in the document are related to only Huawei products. Huawei is not liable for any consequence that results from the violation of universal regulations for safety operations and safety codes on design, production, and equipment use.

Complying with the Local Safety RegulationsWhen operating the device, comply with the local safety regulations. The safety precautions provided in the documents are supplementary. You must comply with the local safety regulations.

Qualified Personnel OnlyThe personnel in charge of installation and maintenance must be trained and master the correct operating methods and safety precautions before beginning work.

SymbolsThis symbol indicates that casualty or serious accident may occur if you ignore the safety instruction. This symbol indicates that serious or major injury may occur if you ignore the safety instruction. This symbol indicates that the operation may be easier if you pay attention to the safety instruction.

Safety of Personnel The high voltage power supply provides power for running the system. Direct contact with the high voltage power supply or contact through damp objects may result in fatal danger. Non-standard and improper high voltage operations may result in fire and electric shock. In a thunderstorm, do not perform operations on high voltage and AC power supply facilities or on a steel tower and mast. Ground the device before powering on the device. Otherwise, the personnel and device are in danger. Power off the device before performing operations on the power supply equipment. High power radio-frequency signals are harmful to human body. Before installing or maintaining an antenna on a steel tower or mast with a large number of transmitter antennas, the operator should coordinate with all parties to ensure that the transmitter antennas are shut down. When handling optical fibers, do not stand close to, or look into the optical fiber outlet with unaided eyes. Protect yourself when drilling holes. Flying dust may hurt your eyes or you may inhale the dust. Power off the batteries before connecting the cables to the batteries. Otherwise, casualties may occur. When working at a height, be cautious about falling objects.

Device Safety Check the electrical connection of the device before operation and ensure that the device is reliably grounded. The static electricity generated by the human body may damage the electrostatic sensitive components on the circuit board, such as the large-scale integrated circuit (LIC). Wear an ESD wrist strap or ESD gloves when performing the operation. When working on batteries, take measures to prevent short circuits in the batteries and electrolyte spill/loss. The electrolyte may erode metal and boards, or even cause rust of the equipment or short circuits in the boards. The NodeB must be powered on within one week after installation.

2

1 Information About the Installation aInstallation Tools

Insulated screwdriver

Cross screwdriver

Straight screwdriver

Adjustable wrench

Socket wrench

Torque wrench

Power cable crimping pliers

RJ-45 crimping pliers

Wire cutter

Rubber hammer

Claw hammer

Cable peeler

Percussion drill

Heat gun

Level bar

Multimeter

Long measuring tape

Vacuum cleaner

3

1 Information About the Installation bInstallation Scenarios2.APM30H

1.APM30

BBU

BBU

3.TMC

4.TMC11H

BBU

BBU

4

1 Information About the Installation bInstallation Scenarios6.PS4890

5.APM30 (+24V

BBU BBU

7. In OMB cabinet

8. In other 19-inch cabinet

9. On the Wall

BBU BBU BBU

5

1 Information About the Installation cBBU Hardware and Cables

1. Appearance of the BBU (Unit: mm)

2. Configuration Principles of the BBU Boards

Board

Mandatory/Op tional Mandatory Mandatory

Full Configuration 2 4

Installation Slot

Remarks

WMPT WBBP

S6 and S7 S0 to S3

Preferentially configured in Slot 7. Preferentially configured in Slot 3, then Slot 2, at last Slot 0,1. Preferentially configured in PWR2. Only in the FAN slot. Preferentially configured in Slot 4, 5. Preferentially configured in Slot 4. Preferentially configured in Slot 4. Preferentially configured in PWR1.

UPEU UBFA UTRP

Mandatory Mandatory Optional

2 1 5

PWR1 and WR2 FAN S0 to S5

UELP UFLP UEIU

Optional Optional Optional

2 2 1

S0 and S4 S0 and S4 PWR1

6

1 Information About the Installation dCable connections of the BBUAlarm Equipment Monitoring Equipment

Power System BBU Power Cable E1 surge protection transfer cable E1 Cable Monitoring Cable Alarm Cable CPRI Optical FE cable FE surge protection transfer cable

e

Procedure

7

2 Installing the BBU in the APM30 aCable connections

NO.

Cable

Installation Position From... To ... PWR on BBU INSIDE on UELP Transmission equipment MON1on BBU CPRI on RRU

1 2 3 4 5

BBU power cable E1 transfer cable E1cable Monitoring cable CPRI

LOAD3 on PDU E1/T1 on WMPT OUTSIDE on UELP TX/RX on APMI CPRI on BBU

8

2 Installing the BBU in the APM30 bInstalling BBU1 Install the mounting ears at both sides of the BBU reversely.

PDU

BBU M6 bolt

2 Slide the BBU case into the cabinet. 3 Check the DIP switches (see appendix).

c

Installing cables1. Install power cable.Connect the OT terminal of the power cable to the LOAD3 terminal of the PDU, and then fix the 3V3 connector of the power cable to the PWR port on the BBU.

LOAD3 NEG(-) RNT(+)

PWRThe power cable is to be made depending on field requirements.

9

2 Installing the BBU in the APM30 bInstalling the BBU cables

2. Install optical cables. Connect one end of the optical cable to CPRI0, CPRI1, or CPRI2 on the WBBP. Then, connect the other end to the RRU. Insert the optical module into CPRI0, CPRI1, or CPRI2. Turn outwards the puller on the optical module.

Optical module Puller

Remove the dustproof caps from the optical connectors. Insert the optical connector at one end of the CPRI optical cable into the optical module. lead the CPRI optical cable out of the cabinet along the left side of the cabinet.

Wrap the fiber tail with the winding pipe till the first cable tie.

Connect the fiber tails labeled 1A and 1B to the CPRI_W port on the RRU. Connect the fiber tails labeled 2A and 2B to one of the CPRI0 to CPRI5 ports on the WMPT.

Optical cable connector

Winding pipe

10

2 Installing the BBU in the APM30 bInstalling the BBU cablesFix the DB25 connector of the E1 transfer cable to the INSIDE port on the UELP and the DB26 connector to the E1/T1 port on the WMPT.

3. Install the E1 transfer cable.

4. Install the E1 cable.Cabling the E1 cable. Fix the DB26 connector of the E1 cable to the OUTSIDE port on the UELP. Strip the jacket off the E1 cable near the grounding point at the lower right corner of the cabinet to expose the shielding layer25mm

E1 cable

E1 transfer cable

Thread the E1 cable through the grounding clip. Then, tighten the screw on the grounding clip to make the shielding layer of the E1 cable in full contact with the grounding clip. Finally, connect the PGND cable on the grounding clip to the grounding bolt of the APM30.Shielding layer of the E1 cable

INSIDE

OUTSIDE

E1/T1

11

2 Installing the BBU in the APM30 bInstalling the BBU Cables5. Install the FE transfer cable (FE transmission mode). Connect one end of the FE transfer cable to the FE0 port near the INSIDE label on the UFLP and the other end to the FE0 port on the WMPT. 6. Install the FE cable (FE transmission). Connect one end of the FE cable to the FE0 port near the OUTSIDE label on the UFLP. Then, lead the other end out of the cabinet along the right side of the cabinet. Strip the jacket off the FE cable near the grounding point at the lower right corner of the cabinet to expose the shielding layer 25mmINSIDE FE0

FE transfer cable FE cable

OUTSIDE FE0

FE0

Thread the FE cable through the grounding clip. Then, tighten the screw on the grounding clip to make the shielding layer of the FE cable in full contact with the grounding clip. Finally, connect the PGND cable on the grounding clip to the grounding bolt of the APM30