analog cmos lab

Experiment 1

Aim:-Layout of Resistor for given value.

Circuit Diagram:-

Theory: - Software Used is L-edit

L-edit: L-Edit, meets needs by combining the fastest rendering available with powerful features that exceed the needs of the most demanding user. Whether you are creating analog or mixed signal ICs, MEMS, or sensors, this leading design tool enables you to get started with minimal training.

We have designed 1kΩ and 10kΩ resistances using L-edit.

Calculation:-R=PL/A

Where A=W.t , P/t=23.6Ω thus while making 1k resistance L=85 um

Making 10k resistance L=850um

Observation and Result:-

L-edit Fig for 1k resistance

R1 1 2 R=1.003k

* R1 PLUS MINUS (1 23 41 29)

* Total Nodes: 2

* Total Elements: 1

1 | P a g eVLSI Design & Simulation Lab 2

* Total Number of Shorted Elements not written to the SPICE file: 0

L-edit Fig for 10k Resistance

Result:-R1 1 2 R=10.005k

Learning Outcome:-

Thus we learned to make two different resistance of 1k and 10k using W=2u=2 lambda and P/t=23.6 i.e. for poly metal. Further e can design different valued resistance.


Experiment 2

Aim:- Plot the static voltage transfer characteristics of a symmetric CMOS inverter utilizing the data points of drain current vs drain to source voltage (Vds) for NMOS and PMOS.

Circuit Diagram:-

Theory:- CMOS is short for Complementary Metal-Oxide Semiconductor. CMOS is an on-board, battery powered semiconductor chip inside computers that stores information.

So far, we have treated transistors as ideal switches

An ON transistor passes a finite amount of current

Depends on terminal voltages

Derive current-voltage (I-V) relationships

Transistor gate, source, drain all have capacitance

I = C (DV/Dt) -> Dt = (C/I) DV

Calculation:- To Plot Id vs. Vds characteristic in first quadrant calculation required is:- Level 1 Parameters

Vgsn=Vin Vgsn=Vin

Vgsp=Vin-Vdd Vgsp+Vdd=Vin

Vdsn=Vout Vdsn=Vout

Vdsp=Vout-Vdd Vdsp+vdd=Vout

Observation & Results

Tspice Code for Nmos and Pmos

For Nmos


.model nmos nmos Level=1

+ Vto=1.0 Kp=3.0E-5 Gamma=0.35

+ Phi=0.65 Lambda=0.02 Tox=0.1u

+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u

+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5

+ Cgbo=2.0E-10 Cgdo=4.00E-11 Cgso=4.00E-11

+ Rd=10.0 Rs=10.0 Rsh=30.0

.model pmos pmos Level=1

+ Vto=-1.0 Kp=3.0E-5 Gamma=0.35


+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u

+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5


+ Rd=10.0 Rs=10.0 Rsh=30.0

m1 d1 g1 0 0 nmos w=10u l=10u

vgs g1 0

vds d1 0

.dc vds 0 5 0.1 vgs 0 5 1

.print I(m1,d1)

.end


T spice Fig For Nmos at different Vgs

Similarly For Pmos

m1 d1 g1 vdd vdd pmos w=10 l=10

vdd vdd 0 5

vgs g1 vdd

vds d1 vdd

.dc vds 0 -5 0.1 vgs 0 -5 1

.print I(m1,d1)

.end

T spice Fig of Pmos for different Vgs


Matlab Code

Nmos=[V I];

Pmos=[V I];

idn=nmos(:,2);

idp=pmos(:,2);

vdsn=nmos(:,1);

vdsp=pmos(:,1);

idp1=idp(1:51);

idp2=idp(52:102);

idp3=idp(103:153);

idp4=idp(154:204);

idp5=idp(205:255);

idp6=idp(256:306);

idn1=idn(1:51);

idn2=idn(52:102);

idn3=idn(103:153);

idn4=idn(154:204);

idn5=idn(205:255);

idn6=idn(256:306);

vdsp1=vdsp(1:51);

vdsp2=vdsp(52:102);

vdsp3=vdsp(103:153);





vdsn1=vdsn(1:51);

vdsn2=vdsn(52:102);

vdsn3=vdsn(103:153);




plot(vdsn1,id1n)

hold on

plot(vdsn2,id2n)

hold on

plot(vdsn3,id3n)

hold on

plot(vdsn4,id4n)

hold on

plot(vdsn5,id5n)

hold on

plot(vdsn6,id6n)

hold on

plot(5+vdsp1,-id1p,'r')

hold on


hold on


hold on



hold on


hold on


hold on

figure

vin=[0 1 2 3 4 5]

vout=[5 5 4.7 0.2 0 0];

plot(vin,vout)

Matlab Figures

Vin Vs. Vout charecteristics for Cmos


Vds Vs.Id Charecteristics For Cmos

Learning Outcome:-

We learn to plot nmos,pmos charestristics in Tspice and then using Tspice .out files in Matlab to Check Id vs Vds and Vin vs Vout.Further Some modification done to hold the waveform and plot both nmos and pmos Charesteristics in First Quadrant.


Experiment 3Aim:- Analysis of switching point(switching threshold) of a cmos inverter and study its variations with reference to transconductance parameter K r and supply voltage V DD.

Circuit Diagram:-

Cmos Inverter

Vm is defined as the intersection of the line Vin = Vout and the inverter VTC. In this region, both the NMOS and PMOS transistors are in saturation since VDS = VGS. The voltage dropped across the NMOS device equals the voltage dropped across the PMOS device when the input voltage is VM. For a very short time, both devices see enough forward bias voltage to drive them to saturation.

In first graph, we plot drain voltage vs gate voltage at different nmos width in T-spice. Since all other terms remains contant except width of nmos, so value of K r changes. As we know that Kn=wn .un.Cox/l

K p=w p .up.Cox/l

K r=Kn/Kp

The graph has two plots, and the intersection point gives value of input voltage at particular width of nmos or at particular K r. We repeat this experiment at different values of K r and note the intersection point i.e vin.

Similarly,in second graph if we vary supply voltage i.e vdd we examine graph’s the center point or intersection point which is known as V m .

Calulation

FOR KR


As we know that Kn=wn .un.Cox/l and K p=w p .up.Cox/l

K r=kn/kp. So, we find vin at different value of k.Here,w p remains constant

wn 10 20 30 40 50K r 1 2 3 4 5

Vin 2.5 2.25 2.11 2.01 1.94

For Vdd

Here at different Vdd we plot values of switching point i.e Vm.

Vdd 5 4 3 2 1Vm 2.5 2 1.5 1.05 0.43

Obsevation and Results:-

Tspice nmos and pmos Level 1 parameters

.model nmos nmos Level=1+ Vto=1.0 Kp=3.0E-5 Gamma=0.35 + Phi=0.65 Lambda=0.02 Tox=0.1u + Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u + Tpg=1.00 Uo=700.0 Af=1.2+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8+ Pb=0.75 Cj=2.0E-4 Mj=0.5+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5+ Cgbo=2.0E-10 Cgdo=4.00E-11 Cgso=4.00E-11 + Rd=10.0 Rs=10.0 Rsh=30.0

.model pmos pmos Level=1+ Vto=-1.0 Kp=3.0E-5 Gamma=0.35 + Phi=0.65 Lambda=0.02 Tox=0.1u + Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u + Tpg=1.00 Uo=700.0 Af=1.2+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8+ Pb=0.75 Cj=2.0E-4 Mj=0.5+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5+ Cgbo=2.0E-10 Cgdo=4.00E-11 Cgso=4.00E-11 + Rd=10.0 Rs=10.0 Rsh=30.0

Tspice code for Cmosm1 d1 g1 0 0 nmos w=10u l=10um2 d1 g1 vdd vdd pmos w=10u l=10uvin g1 0


vdd vdd 0 5 .dc vin 0 5 0.1.plot v(d1) v(g1)

Cmos Charecteristics

we write matlab code of above readings and We get exponential graph between k and vin.

MATLAB CODE

Using above calculated DataFor Krk=[1 2 3 4 5];vin= [2.5 2.25 2.11 2.01 1.94];plot(kr,vin)

Kr vs vin plot


FOR VDD

MATLAB CODE

vm=[2.5 2 1.5 1.05 0.43];vdd= [5 4 3 2 1];plot(vdd,vm);

1

Learning outcomes: In this experiment I have learnt

Plot kr vs vin

Plot vdd vs vin


Experiment 5Aim: Measure the propagation delay of symmetric CMOS inverter and analyze its variation with supply voltage.

Circuit Diagram:-

Theory:-Switching speed - limited by time taken to charge and discharge, CL.

Rise time, tr: waveform to rise from 10% to 90% of its steady state value.

Fall time tf: 90% to 10% of steady state value .

Delay time, td: time difference between input transition (50%) and 50% output level.

Fig : Propagation delay graph

The propagation delay tp of a gate defines how quickly it responds to a change at its inputs, it expresses the delay experienced by a signal when passing through a gate. It is measured between the 50% transition points of the input and output waveforms as shown in the figure 16.1 for an inverting gate. The defines the response time of the gate for a low to high output transition, while refers to a high to low transition. The propagation delay as the average of the two.


Calculation:- No need to calculate any value Tspice itself shows the calculated result

As we vary the different value of input voltage, we get the following values:

Vdd 5 4.5 4 3.5 2.5Tphl 84.77 68.7 52.57 36.10 0.39Tplh 84.38 11.2 15.71 23.59 -500

Observation and Results


+ Vto=1.0 Kp=3.0E-5 Gamma=0.35


+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u

+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5


+ Rd=10.0 Rs=10.0 Rsh=30.0


+ Vto=-1.0 Kp=3.0E-5 Gamma=0.35


+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u

+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5



+ Rd=10.0 Rs=10.0 Rsh=30.0

m1 d1 g1 vdd vdd pmos w=10u l=10u

m2 d1 g1 0 0 nmos w=10u l=10u

c1 d1 0 10pf

vdd vdd 0 5

v1 g1 0 pulse(0 5 0 1fs 1fs 0.5us 1us)

.tran 0.01us 1us

.plot v(d1) v(g1)

.measure tran tphl trig v(g1) val=2.5 rise=1 targ v(d1) val=2.5 fall=1

.measure tran tplh trig v(g1) val=2.5 fall=1 targ v(d1) val=2.5 rise=1

.measure tran trise trig v(g1) val=2.5 rise=1 targ v(d1) val=2.5 rise=1

.measure tran tfall trig v(g1) val=2.5 fall=1 targ v(d1) val=2.5 fall=1

.end

Measurement result summary

tphl = 8.4775e-008


tplh = 8.4388e-008

Similarly

trise = 5.8439e-007

tfall = -4.1523e-007

Matlab Code:-

vdd=[5 4.5 4 3.5 2.5];tphl=[84.77 68.70 52.57 36.10 0.39];plot(vdd,tphl);

Vdd vs TpHL


Learning Outcome:We learn to check values of Tphl,TpLh,Trise,Tfall of an square pulse input using the Ac Transient analysis.Further we ploted vdd vs delays using matlab.

Experiment 4Aim:-Noise Margin of Inverter Based Circuits

a)Calculate Noise Margin for CMOS inverter when Vm=2.5

b)Calculate same noise margin Values for Nmos inverter with Resistance and Nmos Load

Circuit Diagram:-

a)Cmos Inverter b)Resistance as Load c)Nmos as Load

Theory:-

The transfer function of a digital inverter will typically look something like this:


Note that there are essentially three regions to this curve:

I. The region where vI is relatively low, so that the output voltage vo is

high.

II. The region where vI is relatively high, so that the output voltage vO is

low.

III. The transition region, where the input/output voltage is in an indeterminate state (i.e, an ambiguous region between high and low.

Calculation:-

Noise Margin for Resistance as load in Nmos Inverter

VOH=4.92 VIL=1.22

VOL=1.11 VIH=2.50

NM(L)=VIL-VOL=0.11

NM(H)=VOH-VIH=2.42


Noise Margin for Cmos Inverter

VOH=4.96 VIL=1.52

VOL=1.51 VIH=3.233

NM(L)=VIL-VOL=0.01

NM(H)=VOH-VIH=1.73

Noise Margin for Nmos as Load

VOH=3.968 VIL=1.3

VOL=0.47 VOH=4.96

NM(L)=VIL-VOL=0.83

NM(H)=VOH-VIH=2.36

Observation & Results

T spice code for Cmos Inverter

m1 d1 g1 0 0 nmos w=10u l=10u

m2 d1 g1 vdd vdd pmos w=10u l=10u

vin g1 0

vdd vdd 0 5

.dc vin 0 5 0.005

.plot v(d1) v(g1)

.end


Fig for Cmos Inverter

MATLAB CODE:cmos=[Vinput,Voutput];vin=cmos(:,1);vo=cmos(:,2);y=diff(vo);x=diff(vin);z=y./x;vin1=vin(2:51);plot(vin1,z)

PLOT:

For voh:cmos=[Vinput,Voutput];


vin=cmos(:,1);vo=cmos(:,2);plot(vin,vo)

T spice code for Resistance as Load

m1 d1 g1 0 0 nmos w=10u l=10u

r1 vdd d1 100k

vin g1 0

vdd vdd 0 5

.dc vin 0 5 0.005

.plot v(d1) v(g1)

.end


Fig for Resistance as Load

MATLAB CODE:vin=cmos(:,1);vo=cmos(:,2);y=diff(vo);x=diff(vin);z=y./x;vin1=vin(2:51);plot(vin1,z)

cmos=[ Vinput,Voutput];vin=cmos(:,1);vo=cmos(:,2);


plot(vin,vo)

WHEN NMOS IS AT LOAD:

******************************************************


+ Vto=1.0 Kp=3.0E-5 Gamma=0.35


+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u

+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5


+ Rd=10.0 Rs=10.0 Rsh=30.0


+ Vto=-1.0 Kp=3.0E-5 Gamma=0.35


+ Nsub=1.0E+15 Nss=1.0E+10 Ld=0.8u


+ Tpg=1.00 Uo=700.0 Af=1.2

+ Kf=1.0E-26 Is=1.0E-15 Js=1.0E-8

+ Pb=0.75 Cj=2.0E-4 Mj=0.5

+ Cjsw=1.00E-9 Mjsw=0.33 Fc=0.5


+ Rd=10.0 Rs=10.0 Rsh=30.0

m1 d g 0 0 nmos w=10u l=10u

m2 vdd vdd d d nmos w=10u l=10u

vin g 0

vdd vdd 0 5

.dc vin 0 5 0.1

.plot v(d)v(vin)

.end

MATLAB CODE:cmos=[ Vinput,Voutput];vin=cmos(:,1);vo=cmos(:,2);y=diff(vo);x=diff(vin);z=y./x;vin1=vin(2:51);plot(vin1,z)


cmos=[ Vinput,Voutput];vin=cmos(:,1);vo=cmos(:,2);plot(vin,vo)

Learning Outcome:-

We learn the variation occurred due to change in Cmos inverter as resistance as a load & Nmos as a Load.Thus we conclude Noise Margin of resistance is better than Cmos inverter and Nmos as load


analog cmos lab

Documents

nmos w

voutvdd vdsp vdd

vinvdd vgsp vdd

model nmos nmos level

pmosm1 d1 g1 vdd vdd

pmosfor nmos

model pmos pmos level

vgs g1 vddvds d1 vdd