w.a loviyantara
Post on 14-Apr-2018
229 Views
Preview:
TRANSCRIPT
-
7/28/2019 W.A Loviyantara
1/57
Introduction to IEEE 802.15.4LR-WPANs/ZigBee
-
7/28/2019 W.A Loviyantara
2/57
WITS Lab, NSYSU.2
OutlineIntroduction
General Description
Network topologies
PHY Sublayer
MAC Sublayer
Superframe Structure
Frame Structure
PHY Specification
2450 MHz Mode
868/915 MHz Mode
-
7/28/2019 W.A Loviyantara
3/57
Introduction
-
7/28/2019 W.A Loviyantara
4/57
WITS Lab, NSYSU.4
The IEEE 802 Family802.1 => Spanning Tree Bridge
802.2 => Logical Link Control (LLC) Protocol
802.3 => CSMA/CD Networks (Ethernet) MAC Protocol802.4 => Token Bus Networks MAC Protocol
802.5 => Token Ring Networks MAC Protocol
802.6 => Metropolitan Area Networks (MAN)
802.11 => WLAN (wireless local area network)802.11b => 2.4GHz Band; 11 Mbps; direct-sequence
802.11a => 5.0GHz Band; 54 Mbps; OFDM
802.11g => 2.4GHz Band; 54 Mbps; OFDM
802.15 => WPAN (wireless personal area network)
802.15.3 UWB (Ultra Wide Band)
802.15.4 LR-WPAN (low rate wireless PAN)
802.16 => WLL (wireless local loop)
LAN
-
7/28/2019 W.A Loviyantara
5/57
WITS Lab, NSYSU.5
OverviewLR-WPANs stands forlow-rate wireless personal area
networks.
Wireless personal area networks (WPANs) are used to
convey information over relatively short distance.
Unlike wireless local area networks (WLANs),
connections effected via WPANs involve little or no
infrastructure. This feature allows small, power-efficient,
inexpensive solutions to be implemented for a wide
range of devices.
Typically operating in thepersonal operating space
(POS) of 10m.
-
7/28/2019 W.A Loviyantara
6/57
WITS Lab, NSYSU.6
ZigBee & IEEE 802.15.4
-
7/28/2019 W.A Loviyantara
7/57
WITS Lab, NSYSU.7
ZigBee MembershipZigBee Alliance grows to over 90 members (August 16,
2004)
Promoter
Ember
Honeywell
Invensys
Mitsubishi Electric
Motorola
Philips
Samsung
-
7/28/2019 W.A Loviyantara
8/57
WITS Lab, NSYSU.8
Traffic TypesPeriodic data
Sensors
Intermittent data
Light switch
Repetitive, low-latency data
Mouse
The raw data rate will be high enough (maximum of 250
kb/s) to satisfy a set of simple needs such as interactivetoys, but scalable down to the needs of sensor and
automation needs (20 kb/s or below) for wireless
communications.
-
7/28/2019 W.A Loviyantara
9/57
General Description
-
7/28/2019 W.A Loviyantara
10/57
WITS Lab, NSYSU.10
General DescriptionA LR-WPAN is a simple, low-cost communication
network that allows wireless connectivity in applications
with limited power and relaxed throughput requirements.
Some of the characteristics of an LR-WPAN are:
Over-the-air data rates of 250 kb/s, 40 kb/s, and 20 kb/s.
Star or peer-to-peer operation
Allocated 16 bit short or 64 bit extended addresses
Allocation ofguaranteed time slots (GTSs)
Carrier sense multiple access with collision avoidance
(CSMA-CA) channel access
Fully acknowledged protocol for transfer reliability
-
7/28/2019 W.A Loviyantara
11/57
WITS Lab, NSYSU.11
General DescriptionLow power consumption
Energy detection (ED)
Link quality indication (LQI)16 channels in the 2450 MHz band, 10 channels in the 915
MHz band, and 1 channel in the 868 MHz band
Two different device types can participate in an LR-WPAN network:
Full-function device (FFD)
Can talk to RFDs or other FFDs.Reduced-function device (RFD)
Can only talk to an FFD.
Intended for applications that are extremely simple.
-
7/28/2019 W.A Loviyantara
12/57
WITS Lab, NSYSU.12
Components of the IEEE 802.15.4 WPANThe most basic component in the IEEE 802.15.4 WPAN
is the device.
A device can be an RFD or an FFD.
Two or more devices within a POS communicating on
the same physical channel constitute a WPAN.
A network shall include at least one FFD, operating as
the PAN coordinator.
An IEEE 802.15.4 network is part of the WPAN familyof standards.
-
7/28/2019 W.A Loviyantara
13/57
WITS Lab, NSYSU.13
Network TopologiesDepending on the application requirements, the LR-
WPAN may operate in either of two topologies: the star
topology or thepeer-to-peer topology.Each independent PAN will select a unique identifier.
-
7/28/2019 W.A Loviyantara
14/57
WITS Lab, NSYSU.14
Star TopologyThe communication is established between devices and
a single central controller, called the PAN coordinator.
A PAN coordinator is the primary controller of the PAN.
The PAN coordinator may be mains powered, while the
devices will most likely be battery powered.
Applications that benefit from a star topology include
home automation, personal computer (PC) peripherals,
toys and games, and personal health care.
-
7/28/2019 W.A Loviyantara
15/57
WITS Lab, NSYSU.15
Star Network FormationAfter an FFD is activated for the first time, it may
establish its own network and become the PAN
coordinator.
All star networks operate independently from all other
star networks currently in operation. This is achieved by
choosing a PAN identifier, which is not currently usedby other network within the radio sphere of influence.
Once the PAN identifier is chosen, the PAN coordinator
can allow other devices to join its network; both FFDs
and RFDs may join the network.
-
7/28/2019 W.A Loviyantara
16/57
WITS Lab, NSYSU.16
Peer-to-Peer TopologyThe peer-to-peer topology also has a PAN coordinator.
Any device can communicate with any other device as
long as they are in range of one another.Allows more complex network formations to beimplemented, such as mesh networking topology.
Applications such as industrial control and monitoring,wireless sensor networks, asset and inventory tracking,intelligent agriculture, and security would benefit from
such a network topology.Can be ad hoc, self-organizing and self-healing.
Allow multiple hops to route messages from any device
to any other device on the network.
-
7/28/2019 W.A Loviyantara
17/57
WITS Lab, NSYSU.17
Peer-to-peer Network FormationEach device is capable of communicating with any other
device within its radio sphere of influence.
One device will be nominated as the PAN coordinator,for instance, by virtue of being the first device to
communicate on the channel.
An example of the use of the peer-to-peercommunications topology is the cluster-tree.
The cluster-tree network is a special case of a peer-to-peer
network in which most devices are FFDs.
An RFD may connect to a cluster tree network as a leave node
at the end of a branch, because it may only associate with one
FFD at a time.
-
7/28/2019 W.A Loviyantara
18/57
WITS Lab, NSYSU.18
Topology Models
Full function device
Reduced function device
PAN Coordinator
Cluster treeStar Mesh
-
7/28/2019 W.A Loviyantara
19/57
WITS Lab, NSYSU.19
LR-WPAN Device ArchitectureThe upper layers consist of
a network layer, which
provides networkconfiguration,
manipulation, and
message routing.
an application layer
provides the intended
function of the device.
LLC: logical link control.
SSCS: service specific
convergence sublayer.
-
7/28/2019 W.A Loviyantara
20/57
WITS Lab, NSYSU.20
PHY SublayerThe PHY provides two services
The PHY data service
The PHY management service interfacing to thephysical layermanagement entity (PLME).
The PHY data service enables the transmission and
reception ofPHY protocol data units (PPDUs) acrossthe physical radio channel.
The features of the PHY are activation and deactivation
of the radio transceiver, ED, LQI, channel selection,clear channel assessment(CCA), and transmitting as
well as receiving packets across the physical medium.
-
7/28/2019 W.A Loviyantara
21/57
WITS Lab, NSYSU.21
ZigBee Operating Bands
868MHz / 915MHz
PHY
2.4 GHz
868.3 MHz
Channel 0 Channels 1-10
Channels 11-26
2.4835 GHz
928 MHz902 MHz
5 MHz
2 MHz
2.4 GHz
PHY
-
7/28/2019 W.A Loviyantara
22/57
WITS Lab, NSYSU.22
Frequency Band and Data Rate
BPSK-92 dbm1040 kbpsAmericasISM915 MHz
BPSK-92 dbm120 kbpsEurope868 MHz
O_QPSK-85 dbm16250 kbpsWorldwideISM2.4 GHz
ModulationRxSensitivity
# ofChannels
DataCoverageBandFrequency
-
7/28/2019 W.A Loviyantara
23/57
WITS Lab, NSYSU.23
MAC SublayerThe MAC sublayer provides two services:
The MAC data service
The MAC management service interfacing to theMACsublayer management entity (MLME) service access point(SAP).
The MAC data service enables the transmission andreception of MAC protocol data units (MPDUs) acrossthe PHY data service.
The features of the MAC sublayer are beacon
management, channel access, GTS management, framevalidation, acknowledged frame delivery, association,and disassociation.
-
7/28/2019 W.A Loviyantara
24/57
WITS Lab, NSYSU.24
Superframe StructureThe LR-WPAN standard allows the optional use of a superframe
structure.
The format of the superframe is defined by the coordinator.The superframe is bounded by network beacons, is sent by the
coordinator, and is divided into 16 equally sized slots.
The beacon frame is transmitted in the first slot of eachsuperframe.
If a coordinator does not wish to use a superframe structure, it
may turn off the beacon transmissions.
The beacons are used to synchronize the attached devices, to
identify the PAN, and to describe the structure of the superframes.
-
7/28/2019 W.A Loviyantara
25/57
WITS Lab, NSYSU.25
Superframe Structure without GTSs
-
7/28/2019 W.A Loviyantara
26/57
WITS Lab, NSYSU.26
Superframe Structure with GTSs
-
7/28/2019 W.A Loviyantara
27/57
WITS Lab, NSYSU.27
Frame StructureThe LR-WPAN defines four frame structures
A beacon frame, used by a coordinator to transmit beacons
A data frame, used for all transfers of data
An acknowledgement frame, used for confirming successful
frame reception
A MAC command frame, used for handling all MAC peerentity control transfers
-
7/28/2019 W.A Loviyantara
28/57
WITS Lab, NSYSU.28
Schematic View of the Beacon Frame
-
7/28/2019 W.A Loviyantara
29/57
WITS Lab, NSYSU.29
Schematic View of the Data Frame
-
7/28/2019 W.A Loviyantara
30/57
WITS Lab, NSYSU.30
Schematic View of the AcknowledgementFrame
-
7/28/2019 W.A Loviyantara
31/57
WITS Lab, NSYSU.31
Schematic View of the MAC CommandFrame
-
7/28/2019 W.A Loviyantara
32/57
WITS Lab, NSYSU.32
Concept of Primitives
-
7/28/2019 W.A Loviyantara
33/57
PHY Specification
-
7/28/2019 W.A Loviyantara
34/57
WITS Lab, NSYSU.34
Introduction
The PHY is responsible for the following tasks:
Activation and deactivation of the radio transceiver
Energy detection (ED) within the current channel
LQI for received packets
CCA for CSMA-CA
Channel frequency selectionData transmission and reception
-
7/28/2019 W.A Loviyantara
35/57
WITS Lab, NSYSU.35
Operating Frequency Range
Frequency bands and data rates
-
7/28/2019 W.A Loviyantara
36/57
WITS Lab, NSYSU.36
Channel Assignments and Numbering
A total of 27 channels, numbered 0 to 26, are available
across the three frequency bands.
Sixteen channels in the 2450 MHz band.Ten channels in the 915 MHz band.
One channels in the 868 MHz band.
The center frequency of these channels is defined as
follows:
-
7/28/2019 W.A Loviyantara
37/57
WITS Lab, NSYSU.37
Receiver Sensitivity Definition
-
7/28/2019 W.A Loviyantara
38/57
WITS Lab, NSYSU.38
General Packet Format
Each PPDU packet consists of the following basic
components:
A SHR (synchronization header), which allows a receivingdevice to synchronize and lock onto the bit stream.
A PHR (PHY header), which contains frame length information.
A variable length payload, which carriers the MAC sublayerframe.
General packet format
-
7/28/2019 W.A Loviyantara
39/57
WITS Lab, NSYSU.39
Packet Fields
Preamble field
Used by the transceiver to obtain chip and symbol
synchronization with an incoming message.Composed of 32 binary zeros.
SFD (start-of-frame delimiter) fieldAn 8 bit field indicating the end of the synchronization
(preamble) field and the start of the packet data.
Format of the SFD field
-
7/28/2019 W.A Loviyantara
40/57
WITS Lab, NSYSU.40
Packet Fields
Frame length field
7 bits in length and specifies the total number of octets
contained in the PSDU.
PSDU field
Has a variable length and carries the data of the PHY packet.For all packet types of length five octets or greater than seven
octets, the PSDU contains the MAC sublayer frame (i.e.,
MPDU).
-
7/28/2019 W.A Loviyantara
41/57
WITS Lab, NSYSU.41
PHY Constants
-
7/28/2019 W.A Loviyantara
42/57
WITS Lab, NSYSU.42
PHY PIB Attributes
PIB: PAN information base.
-
7/28/2019 W.A Loviyantara
43/57
WITS Lab, NSYSU.43
2450 MHz PHY Specifications
Data rate: 250 kb/s.
Modulation and spreading
Employs a 16-ary quasi-orthogonal modulation technique.
During each data symbol period, four information bits are used
to select one of 16 nearly orthogonal pseudo-random noise
(PN) sequences to be transmitted.The PN sequences for successive data symbols are
concatenated.
The aggregate chip sequence is modulated onto the carrier
using offset quadrature phase-shift keying (O-QPSK)
-
7/28/2019 W.A Loviyantara
44/57
WITS Lab, NSYSU.44
2450 MHz PHY Specifications
Reference modulator diagram
Reference transmitter diagram
-
7/28/2019 W.A Loviyantara
45/57
WITS Lab, NSYSU.45
Symbol to Chip Mapping
-
7/28/2019 W.A Loviyantara
46/57
WITS Lab, NSYSU.46
2450 MHz PHY Specifications
O-QPSK modulation
The chip sequences representing each data symbol are
modulated onto the carrier using O-QPSK with half-sinepulse shaping.
Pulse shape
( )sin 0 2
2
0
c
c
t t Tp t T
otherwise
=
-
7/28/2019 W.A Loviyantara
47/57
WITS Lab, NSYSU.47
2450 MHz PHY Specifications
Sample baseband chip sequences with pulse shaping
Symbol rate
The 2450 MHz PHY symbol rate shall be 62.5 ksymbol/s.
Receiver sensitivityA compliant device shall be capable of achieving a sensitivityof -85 dBm or better.
-
7/28/2019 W.A Loviyantara
48/57
WITS Lab, NSYSU.48
868/915 MHz PHY Specifications
868/915 MHz band data rates
868 MHz: 20 kb/s.
915 MHz: 40 kb/s.
Modulation and Spreading
The 868/915 MHz PHY shall employ direct sequence spreadspectrum (DSSS).
The binary phase-shift keying (BPSK) is used for chip
modulation.Differential encoding is used for data symbol encoding.
-
7/28/2019 W.A Loviyantara
49/57
WITS Lab, NSYSU.49
868/915 MHz PHY Specifications
Reference modulator diagram
Differential encoding
Differential encoding is the modulo-2 addition (exclusive or)of a raw data bit.
1
1
is the raw data bit being encoded,
is the corresponding differentially encoded bit,
is the previous differentially encoded bit.
n n n
n
n
n
E R E
R
E
E
=
-
7/28/2019 W.A Loviyantara
50/57
WITS Lab, NSYSU.50
868/915 MHz PHY Specifications
For each packet transmitted,R1 is the first raw bit to be
encoded andE0 is assumed to be zero.
Conversely, the decoding process, as performed at thereceiver, can be described by:
For each packet received,E1 is the first bit to be decoded,
andE0 is assumed to be zero.
Bit-to-chip mapping
Each input bit shall be mapped into a 15-chip PN sequence
1n n nR E E=
-
7/28/2019 W.A Loviyantara
51/57
WITS Lab, NSYSU.51
868/915 MHz PHY Specifications
BPSK modulation
The chip sequences are modulated onto the carrier using
BPSK with raised cosine pulse shaping (roll-off factor = 1).The chip rate is 300 kchip/s for the 868 MHz band and 600
kchip/s in the 915 MHz band.
Pulse shape
The raised cosine pulse shape (roll-off factor = 1) used to
represent each baseband chip is described by
( )( ) ( )
( )2 2sin / cos /
/ 1 4 /
c
c
t T t T p t
t T t T
=
-
7/28/2019 W.A Loviyantara
52/57
WITS Lab, NSYSU.52
868/915 MHz PHY Specifications
Symbol rate
868 MHz: 20 ksymbol/s
915 MHz: 40 ksymbol/s
Receiver sensitivity
A compliant device shall be capable of achieving a sensitivityof -92 dBm or better.
-
7/28/2019 W.A Loviyantara
53/57
WITS Lab, NSYSU.53
Receiver Architecture
Half-sine
Matched Filter
A/D
Packet
Detection
Fine Syn.
and/or
Start of Data
Down
Sampling
to Chip Rate
RF
Over-Sampling
Rate (nchip rate)
Coarse
Synchronization
Despreading
to
(Sym. Rate)
OQPSK
Demodulation
(Sym. Rate)
Detection
(Sym. Rate)
Data Stream
D d d D d l
-
7/28/2019 W.A Loviyantara
54/57
WITS Lab, NSYSU.54
Despreading and Demodulation
CI1 CI2 CI3 CI4 CI5 CI6 CI16
CQ1 CQ2 CQ3 CQ4 CQ5 CQ6 CQ16
F
i
n
d
M
a
x
i
mu
m
+
-
+
+
CSMA/CA Al i h
-
7/28/2019 W.A Loviyantara
55/57
WITS Lab, NSYSU.55
CSMA/CA Algorithm
The CSMA/CA algorithm shall be used before the
transmission ofdata or MAC command frames
transmitted within the CAP, and shall not be used for
the transmission ofbeacon frames, acknowledgment
frames or data frames transmitted in the CFP.
NB is the number of times the CSMA/CA algorithmwas required to backoff.
CWdefines the number ofbackoffperiods that need
to be clear of channel activity.BEis related to how many backoffperiods a device
shall wait before assess a channel.backoff = 20 symbols
CSMA-CA
-
7/28/2019 W.A Loviyantara
56/57
WITS Lab, NSYSU.56
Slotted
BE=lesser of (2,macMinBE)
BE=macMinBE
Delay for random
unit backoff periods
Locate backoffperiod boundary
(2 1)BE
Battery life
extension?
NB=0,CW=2
Performance CCA on
backoff period boundary
Channel
idle?
CW=2,NB=NB+1,
BE=min(BE+1,aMaxBE)
CW=CW-1
NB>macMaxCS
MABackoff? CW=O?
Failure Success
N
Y
Y
N
N
N
Y Y
CSMA-CA
-
7/28/2019 W.A Loviyantara
57/57
WITS Lab, NSYSU.57
Unslotted
NB=0,
BE=macMinBE
Delay for random
unit backoff periods
(2 1)BE
Perform CCA
Channel
idle?
NB=NB+1,
BE=min(BE+1,aMaxBE)
NB>macMaxCS
MABackoffs?
Failure Success
N
N
Y
Y
top related