yzf-r6 - journey.czjourney.cz/moto/navody/yamaha r6 1999 owners manual.pdfeau00002 introduction...
TRANSCRIPT
5MT-28199-11LIT-11626-15-32
YZF-R6PYZF-R6PC
OWNER’S MANUAL
PRINTED IN JAPAN2001 . 7 - 4.0 × 1 CR
(E)
PRINTED ON RECYCLED PAPER
YAMAHA MOTOR CO., LTD.
EAU03438
00002 INTRODUCTION
F-R6/YZF-R6C. This model ison of fine sporting, touring, and degree of craftsmanship andlds.
peration, inspection, and basictions concerning the operationYamaha dealer.
cle fully comply with the emis- manufacture. Yamaha has metr economy of operation of the important that you and youred maintenance schedules and
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
EAU
Congratulations on your purchase of the Yamaha YZthe result of Yamaha’s vast experience in the productipacesetting racing machines. It represents the highreliability that have made Yamaha a leader in these fie
This manual will give you an understanding of the omaintenance of this motorcycle. If you have any quesor maintenance of your motorcycle, please consult a
The design and manufacture of this Yamaha motorcysions standards for clean air applicable at the date ofthese standards without reducing the performance omotorcycle. To maintain these high standards, it isYamaha dealer pay close attention to the recommendoperating instructions contained within this manual.
EAU00003PORTANT MANUAL INFORMATION
ticularly important information is distinguished in this manual by the following notations:
ERT! YOUR SAFETY IS
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
IM
Par
re injury or death to thepairing the motorcycle.
to avoid damage to the
learer.
torcycle and should remain
d quality. Therefore, whilelable at the time of printing,d this manual. If you haveaha dealer.
C
N
The Safety Alert Symbol meINVOLVED!
WARNING Failure to follow WARNING inmotorcycle operator, a bystan
AUTION: A CAUTION indicates specialmotorcycle.
OTE: A NOTE provides key informati
NOTE:@
� This manual should be considwith it even if the motorcycle
� Yamaha continually seeks adthis manual contains the mosthere may be minor discrepaany questions concerning this
@
ans ATTENTION! BECOME AL
structions could result in seveder or a person inspecting or re
precautions that must be taken
on to make procedures easier or c
ered a permanent part of this mois subsequently sold.vancements in product design ant current product information avaincies between your motorcycle an manual, please consult your Yam
IMPORTANT MANUAL INFORMATIONEW000000
IS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDINGAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTOR-TTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE AT-E KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURESAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES.TIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDINGURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELI-OTORCYCLE.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
WARNING@
PLEASE READ THTIPS” BOOKLET CCYCLE. DO NOT ATAINED ADEQUATAND UNTIL YOU HREGULAR INSPECSKILLS, WILL ENSABILITY OF THIS M@
IMPORTANT MANUAL INFORMATION
AFFIX DEALER
EAU04247
© 2001
Aw
Y
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
LABEL HERE
YZF-R6P/YZF-R6PCOWNER’S MANUAL
by Yamaha Motor Corporation, U.S.A.1st edition, July 2001All rights reserved.
ny reprinting or unauthorized useithout the written permission of
amaha Motor Corporation, U.S.A.is expressly prohibited.
Printed in Japan.P/N LIT-11626-15-32
LE OF CONTENTS
1
2
FUNCTIONS 3
4
T RIDING POINTS 5
D MINOR REPAIR 6
ORAGE 7
8
9
EAU00009
E_5MT.book
TAB
1 SAFETY INFORMATION
2 DESCRIPTION
3 INSTRUMENT AND CONTROL
4 PRE-OPERATION CHECKS
5 OPERATION AND IMPORTAN
6 PERIODIC MAINTENANCE AN
7 MOTORCYCLE CARE AND ST
8 SPECIFICATIONS
9 CONSUMER INFORMATION
Page 1 Tuesday, August 28, 2001 2:05 PM
INDEX
SAFETY INFORMATION
1
Safe riding .......................................................................................... 1-1Protective apparel .............................................................................. 1-3Modifications ...................................................................................... 1-3Loading and accessories ................................................................... 1-3Gasoline and exhaust gas.................................................................. 1-5Location of important labels .............................................................. 1-7
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
1
EAU00014
USE AND OPERATION ARE DE-AS WELL AS THE EXPERTISE OF
LLOWING REQUIREMENTS BE-
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
SOURCE ON ALL ASPECTS OF
ENTS IN THE OWNER’S MANU-
G TECHNIQUES.TED BY THE OWNER’S MANUALITIONS.
event an accident.er.raffic is the predominating cause ofaused by an automobile driver whos to be very effective in reducing the
rough intersections, since intersec-ccur.her motorist’s blind spot.
1-1
1-SAFETY INFORMATION
MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOFORE RIDING THIS MOTORCYCLE.HE OR SHE SHOULD:1. OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT
MOTORCYCLE OPERATION.2. OBSERVE THE WARNINGS AND MAINTENANCE REQUIREM
AL.3. OBTAIN QUALIFIED TRAINING IN SAFE AND PROPER RIDIN4. OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICA
AND/OR WHEN MADE NECESSARY BY MECHANICAL COND
Safe riding
1. Always make pre-operation checks. Careful checks may help pr2. This motorcycle is designed to carry the operator and a passeng3. The failure of motorists to detect and recognize motorcycles in t
automobile/motorcycle accidents. Many accidents have been cdid not see the motorcycle. Making yourself conspicuous appearchance of this type of accident.
Therefore:a. Wear a brightly colored jacket.b. Use extra caution when you are approaching and passing th
tions are the most likely places for motorcycle accidents to oc. Ride where other motorists can see you. Avoid riding in anot
FETY INFORMATION
1
operators who have been involved in
r motorcycle to other qualified opera-
elp you to avoid an accident.here there is no traffic until you have controls.perator. A typical error made by the or undercornering (insufficient lean
rranted by road and traffic conditions.that other motorists can see you.er control.d both feet on the operator footrests
at strap or grab bar, if equipped, with
both feet on the passenger footrests.
le for off-road use.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
SA
1-2
4. Many accidents involve inexperienced operators. In fact, many accidents do not even have a current motorcycle license.a. Make sure that you are qualified and that you only lend you
tors.b. Know your skills and limits. Staying within your limits may hc. We recommend that you practice riding your motorcycle w
become thoroughly familiar with the motorcycle and all of its5. Many accidents have been caused by error of the motorcycle o
operator is veering wide on a turn due to EXCESSIVE SPEEDangle for the speed).a. Always obey the speed limit and never travel faster than wab. Always signal before turning or changing lanes. Make sure
6. The posture of the operator and passenger is important for propa. The operator should keep both hands on the handlebar an
during operation to maintain control of the motorcycle.b. The passenger should always hold onto the operator, the se
both hands and keep both feet on the passenger footrests.c. Never carry a passenger unless he or she can firmly place
7. Never ride under the influence of alcohol or other drugs.8. This motorcycle is designed for on-road use only. It is not suitab
1
f head injuries. The use of a safety of head injuries.
ld contribute to an impairment of vi-
tive in preventing or reducing abra-
e control levers, footrests, or wheels
ion. They become very hot and cangs, ankles, and feet.
r the removal of original equipment,rsonal injury. Modifications may also
t stability and handling if the weightf an accident, use extreme cautione when riding a motorcycle that hasollow if loading cargo or adding ac-
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
SAFETY INFORMATION
1-3
Protective apparel
The majority of fatalities from motorcycle accidents are the result ohelmet is the single most critical factor in the prevention or reduction1. Always wear an approved helmet.2. Wear a face shield or goggles. Wind in your unprotected eyes cou
sion that could delay seeing a hazard.3. The use of a jacket, heavy boots, trousers, gloves, etc., is effec
sions or lacerations.4. Never wear loose-fitting clothes, otherwise they could catch on th
and cause injury or an accident.5. Never touch the engine or exhaust system during or after operat
cause burns. Always wear protective clothing that covers your le6. A passenger should also observe the above precautions.
Modifications
Modifications made to this motorcycle not approved by Yamaha, omay render the motorcycle unsafe for use and may cause severe pemake your motorcycle illegal to use.
Loading and accessories
Adding accessories or cargo to your motorcycle can adversely affecdistribution of the motorcycle is changed. To avoid the possibility owhen adding cargo or accessories to your motorcycle. Use extra caradded cargo or accessories. Here are some general guidelines to fcessories to your motorcycle:
FETY INFORMATION
1
must not exceed the maximum loadding within this weight limit, keep the
to the motorcycle as possible. Make of the motorcycle to minimize imbal-
t accessories and cargo are securelynts and cargo restraints frequently.ork, or front fender. These items, in-n create unstable handling or a slow
for use on this motorcycle. Sinceu must personally be responsible fors. Use extreme caution when select-
der “Loading” when mounting acces-
rformance of your motorcycle. Care- does not in any way reduce grounding travel or control operation, or ob-
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
SA
1-4
Loading
The total weight of the operator, passenger, accessories and cargolimit of YZF-R6: 417lb (189 kg)/YZF-R6C: 415 lb (188 kg). When loafollowing in mind:1. Cargo and accessory weight should be kept as low and close
sure to distribute the weight as evenly as possible on both sidesance or instability.
2. Shifting weights can create a sudden imbalance. Make sure thaattached to the motorcycle before riding. Check accessory mou
3. Never attach any large or heavy items to the handlebar, front fcluding such cargo as sleeping bags, duffel bags, or tents, casteering response.
Accessories
Genuine Yamaha accessories have been specifically designedYamaha cannot test all other accessories that may be available, yothe proper selection, installation and use of non-Yamaha accessorieing and installing any accessories.Keep the following guidelines in mind, as well as those provided unsories.1. Never install accessories or carry cargo that would impair the pe
fully inspect the accessory before using it to make sure that itclearance or cornering clearance, limit suspension travel, steerscure lights or reflectors.
1
n create instability due to improperare added to the handlebar or front be kept to a minimum. the motorcycle due to aerodynamicycle may become unstable in cross
assing or being passed by large ve-
normal riding position. This improp-d may limit control ability, therefore,
essories exceed the capacity of theich could cause a dangerous loss of
system when refueling..d area. The exhaust fumes are poi- a short time. Always operate your
nded and remove the key from the
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
SAFETY INFORMATION
1-5
a. Accessories fitted to the handlebar or the front fork area caweight distribution or aerodynamic changes. If accessories fork area, they must be as lightweight as possible and should
b. Bulky or large accessories may seriously affect the stability ofeffects. Wind may attempt to lift the motorcycle, or the motorcwinds. These accessories may also cause instability when phicles.
c. Certain accessories can displace the operator from his or herer position limits the freedom of movement of the operator ansuch accessories are not recommended.
2. Use caution when adding electrical accessories. If electrical accmotorcycle’s electrical system, an electric failure could result, whlights or engine power.
Gasoline and exhaust gas
1. GASOLINE IS HIGHLY FLAMMABLE:a. Always turn the engine off when refueling.b. Take care not to spill any gasoline on the engine or exhaust c. Never refuel while smoking or in the vicinity of an open flame
2. Never start the engine or let it run for any length of time in a closesonous and may cause loss of consciousness and death withinmotorcycle in an area that has adequate ventilation.
3. Always turn the engine off before leaving the motorcycle unattemain switch. When parking the motorcycle, note the following:
FETY INFORMATION
1
cycle in a place where pedestrians or
wise it may fall over. a kerosene heater, or near an open
re that it is kept upright. If the motor- or fuel tank.or, or allow gasoline to get into yourr skin or clothing, immediately wash
.
E_5MT.book Page 6 Tuesday, August 28, 2001 2:05 PM
SA
1-6
a. The engine and exhaust system may be hot. Park the motorchildren are not likely to touch these hot areas.
b. Do not park the motorcycle on a slope or soft ground, otherc. Do not park the motorcycle near a flammable source (e.g.,
flame), otherwise it could catch fire.4. When transporting the motorcycle in another vehicle, make su
cycle should lean over, gasoline may leak out of the carburetor5. If you should swallow any gasoline, inhale a lot of gasoline vap
eyes, see your doctor immediately. If any gasoline spills on youthe affected area with soap and water and change your clothes
1
EAU02977
LoPle
E_5MT.book Page 7 Tuesday, August 28, 2001 2:05 PM
SAFETY INFORMATION
1-7
cation of important labels ase read the following important labels carefully before operating this motorcycle.
FETY INFORMATION
1
a only
N HOSE ROUTING
HA MOTOR CO.,LTD.
ANKCARB.
TOATMOSPHERE
TER
E_5MT.book Page 8 Tuesday, August 28, 2001 2:05 PM
SA
1-8
1
2
3
4
5
6
7
Californi
EMISSIO
YAMA
FROMFUEL T
CANIS
DESCRIPTION
2
Left view ............................................................................................. 2-1Right view........................................................................................... 2-2Controls and instruments ................................................................... 2-3
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
2
EAU00026
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
2-DE
Le
mbly spring g (page 3-18)mbly rebound
ting knob (page 3-18)(page 3-9)(page 6-15)
dge (page 6-13)
1.
2.
3.4.5.
2-1
SCRIPTION
ft view
Front fork compression damping force adjusting screw (page 3-17)Front fork rebound damping force adjusting screw (page 3-17)Front fork spring preload adjusting bolt (page 3-16)Air filter element (page 6-19)Shock absorber assembly compression damping force adjusting screw (page 3-19)
6. Shock absorber assepreload adjusting rin
7. Shock absorber assedamping force adjus
8. Shift pedal9. Coolant reservoir
10. Engine oil filter cartri
DESCRIPTION
2
R
1112131415
ervoir (page 6-30)(page 6-12)(page 6-12)(page 3-10)
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
2-2
ight view
. Luggage strap holders (page 3-21)
. Owner’s tool kit (page 6-1)
. Fuses (page 6-39)
. Rear brake fluid reservoir (page 6-30)
. Radiator cap (page 6-17)
16. Front brake fluid res17. Engine oil filler cap18. Engine oil dipstick19. Brake pedal
DE
2
Co
1.2.3.4.5.
(page 3-6)ches (page 3-8)
(page 6-22)(page 3-9)
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
SCRIPTION
2-3
ntrols and instruments
Clutch lever (page 3-9)Left handlebar switches (page 3-7)Starter (choke) lever (page 3-13)Speedometer unit (page 3-5)Main switch/steering lock (page 3-1)
6. Tachometer7. Right handlebar swit8. Throttle grip9. Brake lever
INSTRUMENT AND CONTROL FUNCTIONS
3
Main switch/steering lock .................................................................. 3-1Indicator and warning lights .............................................................. 3-2Speedometer unit .............................................................................. 3-5Tachometer ....................................................................................... 3-6Self-diagnosis device ........................................................................ 3-7Handlebar switches ........................................................................... 3-7Clutch lever ....................................................................................... 3-9Shift pedal ......................................................................................... 3-9Brake lever ........................................................................................ 3-9Brake pedal ..................................................................................... 3-10Fuel tank cap ................................................................................... 3-11Fuel ................................................................................................. 3-11Starter (choke) lever......................................................................... 3-13Seats ............................................................................................... 3-13Helmet holders ................................................................................ 3-15Storage compartment ..................................................................... 3-15Adjusting the front fork .................................................................... 3-16Adjusting the shock absorber assembly .......................................... 3-18Matching the front and rear suspension settings ............................ 3-20Luggage strap holders .................................................................... 3-21Sidestand ........................................................................................ 3-21Ignition circuit cut-off system ........................................................... 3-22
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
3
EAU00027
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
3-IN
EW000016
ARNING turn the key to “OFF” orK” while the motorcycle isg, otherwise the electricals will be switched off, which
esult in loss of control or annt. Make sure that the motor-is stopped before turning the “OFF” or “LOCK”.
..
MaThethe usepos
ONAll powing,tionbe s
OFAll can
3-1STRUMENT AND CONTROL FUNCTIONS
EAU00029
in switch/steering lock main switch/steering lock controlsignition and lighting systems, and isd to lock the steering. The variousitions are described below.
EAU00033
electrical systems are supplied wither, and the headlight, meter light- taillight, license plate light and posi- lights come on, and the engine cantarted. The key cannot be removed.
EAU00038
Felectrical systems are off. The key be removed.
EAU00040
LOCKThe steering is locked, and all electricalsystems are off. The key can be re-moved.
To lock the steering1. Turn the handlebars all the way to
the left.2. Push the key in from the “OFF” po-
sition, and then turn it to “LOCK”while still pushing it.
3. Remove the key.
To unlock the steeringPush the key in, and then turn it to“OFF” while still pushing it.
W@
Never“LOCmovinsystemmay raccidecycle key to@
1. Push2. Turn
NTROL FUNCTIONS
3
In
NThtra
HThhion
1.2.3.4.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-2
EAU03034
dicator and warning lights
EAU00061
eutral indicator light “ ” is indicator light comes on when thensmission is in the neutral position.
EAU00063
igh beam indicator light “ ” is indicator light comes on when the
gh beam of the headlight is switched.
EAU00057
Turn signal indicator light “ ” This indicator light flashes when theturn signal switch is pushed to the leftor right.
EAU04303
Fuel level warning light “ ” This warning light comes on when thefuel level drops below approximately3.5 L (0.8 Imp gal, 0.9 US gal). Whenthis occurs, refuel as soon as possible.The electrical circuit of the warning lightcan be checked according to the fol-lowing procedure.
1. Turn the key to “ON”.2. If the warning light does not come
on for a few seconds, then go off,have a Yamaha dealer check theelectrical circuit.
Neutral indicator light “ ”High beam indicator light “ ”Turn signal indicator light “ ”Fuel level warning light “ ”
IN
3
OilwaThithre
�
EC000118
TION:Do not operate the motorcycleuntil you know that the engineoil level is sufficient. Do not operate the engine if it isoverheated.
E: if the oil is filled to the specified, the warning light may flicker riding on a slope or during sud-acceleration or deceleration, buts normal.
1. O2. O
w3. C
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-3
EAU04397
level/coolant temperature rning light “ ” s warning light has the followinge functions.When the engine oil level is low,the warning light comes on andsymbol “ ” flashes. If this oc-curs, stop the engine immediatelyand add engine oil to the specifiedlevel.
� When the coolant temperature istoo high, the warning light comeson and symbol “ ” flashes. Stopthe motorcycle and allow it to idleuntil the coolant temperature goesdown. If the temperature does notgo down, stop the engine. (Seethe “Engine overheating” sectionon page 6-48 for further instruc-tions.)
� When the engine oil level is lowand the coolant temperature is toohigh, the warning light comes onand symbols “ ” and “ ”flash.
The electrical circuit of the warning lightcan be checked according to the fol-lowing procedure.
1. Turn the engine stop switch to“ ” and the key to “ON”.
2. The warning light will come on,and symbols “ ” and “ ” willappear in the display.
If the warning light does not come onfor a few seconds, then go off, have aYamaha dealer check the electrical cir-cuit.
CAU_
�
�
_
NOT_
Evenlevelwhenden this i_
il level symbol “ ”il level/coolant temperature arning light “ ”oolant temperature symbol “ ”
NTROL FUNCTIONS
3
CB
What to do
OK. Go ahead with riding.
OK. Go ahead with riding.
Stop the motorcycle and allow it toidle until the coolant temperaturegoes down.If the temperature does not godown, stop the engine. (See the“Engine overheating” section onpage 6-48 for further instructions.)
A
Stop the engine and allow it to cool.(See the “Engine overheating” sec-tion on page 6-48 for further in-structions.)
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-4
-19E
Coolant temperature Display Conditions
0–104 °F (0–40 °C)
Symbol and message“LO” are displayed.
105–242 °F (41–117 °C)
Symbol and temperatureare displayed.
243–284 °F (118–140 °C)
Symbol and temperatureflash.Warning light comes on.
bove 284 °F (140 °C)Symbol and message“HI” flash. Warning light comes on.
˚F
˚F
˚F
˚F
IN
3
SpThethe
�
�
�
�
�
between the various tripmeter andmeter modes in the following order:P F → TRIP 1 → TRIP 2 → ODO →P F
reset a tripmeter, select it by push-the “SELECT” button, and then
h the “RESET” button for at least second. If you do not reset the fuelrve tripmeter manually, it will reset
lf automatically and the display willrn to the prior mode after refueling traveling 5 km (3 mi).
1. S2. C3. “4. “
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-5
EAU04264
eedometer unit speedometer unit is equipped with
following:a digital speedometer (whichshows riding speed)an odometer (which shows the to-tal distance traveled)two tripmeters (which show thedistance traveled since they werelast set to zero)a fuel reserve tripmeter (whichshows the distance traveled on thefuel reserve)a clock
NOTE:_
� Be sure to turn the key to “ON” be-fore using the “SELECT” and “RE-SET” buttons.
� To switch the speedometer dis-play between kilometers andmiles, press the “SELECT” buttonand “RESET” button together forat least two seconds.
_
Odometer and tripmeter modesPushing the “SELECT” button switchesthe display between the odometermode “ODO” and the tripmeter modes“TRIP 1” and “TRIP 2” in the followingorder:ODO → TRIP 1 → TRIP 2 → ODO
If the fuel level warning light comes on(see page 3-2), the odometer displaywill automatically change to the fuel re-serve tripmeter mode “TRIP F” andstart counting the distance traveledfrom that point. In that case, pushingthe “SELECT” button switches the dis-
playodoTRITRI
To ing pusonereseitseretuand
peedometerlock/odometer
RESET” buttonSELECT” button
NTROL FUNCTIONS
3
CTomleTomTo
1
2
3
4
5
E_5MT.book Page 6 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-6
lock mode change the display to the clock
ode, push the “SELECT” button for atast one second. change the display back to the prior
ode, push the “SELECT” button. set the clock:. Push the “SELECT” button and
“RESET” button together for atleast two seconds.
. When the hour digits start flashing,push the “RESET” button to setthe hours.
. Push the “SELECT” button, andthe minute digits will start flashing.
. Push the “RESET” button to setthe minutes.
. Push the “SELECT” button andthen release it to start the clock.
EAU00101
Tachometer The electric tachometer allows the riderto monitor the engine speed and keep itwithin the ideal power range.
EC000003
CAUTION:@
Do not operate the engine in the ta-chometer red zone.Red zone: YZF-R6: 15,500 r/min/YZF-R6C: 14,000 r/min and above @
1. Tachometer2. Tachometer red zone
IN
3
SeThiagncal
�
�
If athetheCB-11
EAU00118
ndlebar switches
EAU03888
mer switch “ / ” this switch to “ ” for the highm and to “ ” for the low beam.
immer switch “ / ”urn signal switch “ / ”orn switch “ ”
E_5MT.book Page 7 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-7
EAU03729
lf-diagnosis device s model is equipped with a self-di-osis device for the following electri-
circuits:throttle position sensorspeed sensor
ny of those circuits are defective, tachometer will repeatedly display following error code:E
Use the table below to identify thefaulty electrical circuit.CB-28E
If the tachometer displays such an er-ror code, note the circuit-specific num-ber of r/min, and then have a Yamahadealer check the motorcycle.
EC000004
CAUTION:_
When the tachometer displays anerror code, the motorcycle shouldbe checked as soon as possible inorder to avoid engine damage. _
Ha
DimSetbea
0 r/min for 3 seconds
Circuit-specific number of r/min for 2.5 seconds (See the table below.)
Current engine speed for 3 seconds
Specific r/min Faulty electrical circuit
3,000 r/min Throttle position sensor
4,000 r/min Speed sensor
1. D2. T3. H
NTROL FUNCTIONS
3
TuToswtureteligtu
HPr
EAU00143
art switch “ ” sh this switch to crank the engine
th the starter.EC000005
AUTION:e page 5-1 for starting instruc-ns prior to starting the engine.
E_5MT.book Page 8 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-8
EAU03889
rn signal switch “ / ” signal a right-hand turn, push thisitch to “ ”. To signal a left-hand
rn, push this switch to “ ”. Whenleased, the switch returns to the cen-r position. To cancel the turn signalhts, push the switch in after it has re-rned to the center position.
EAU00129
orn switch “ ” ess this switch to sound the horn.
EAU03890
Engine stop switch “ / ” Set this switch to “ ” before startingthe engine. Set this switch to “ ” tostop the engine in case of an emergen-cy, such as when the motorcycle over-turns or when the throttle cable isstuck.
StPuwi
C@
Setio@
1. Engine stop switch “ / ”2. Start switch “ ”
IN
3
ClThehanclubartherapcluTheclucircfor cut
EAU00161
ake lever brake lever is located at the rightdlebar grip. To apply the frontke, pull the lever toward the handle- grip.
1. C rake lever
E_5MT.book Page 9 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-9
EAU00152
utch lever clutch lever is located at the leftdlebar grip. To disengage the
tch, pull the lever toward the handle- grip. To engage the clutch, release lever. The lever should be pulledidly and released slowly for smoothtch operation. clutch lever is equipped with a
tch switch, which is part of the ignitionuit cut-off system. (See page 3-22an explanation of the ignition circuit-off system.)
EAU00157
Shift pedal The shift pedal is located on the leftside of the engine and is used in com-bination with the clutch lever whenshifting the gears of the 6-speed con-stant-mesh transmission equipped onthis motorcycle.
BrThehanbrabar
lutch lever 1. Shift pedal 1. B
NTROL FUNCTIONS
3
Thsitahawfrothdith
1.2.a.
E_5MT.book Page 10 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-10
e brake lever is equipped with a po-tion adjusting dial. To adjust the dis-nce between the brake lever and thendlebar grip, turn the adjusting dial
hile holding the lever pushed awaym the handlebar grip. Make sure that
e appropriate setting on the adjustingal is aligned with the arrow mark one brake lever.
EAU00162
Brake pedal The brake pedal is on the right side ofthe motorcycle. To apply the rearbrake, press down on the brake pedal.
Brake lever position adjusting dialArrow markDistance between brake lever and handlebar grip
1. Brake pedal
IN
3
Fu
ToOpserit 1leaope
To1.
2.
EAU03753
sure that there is sufficient fuel innk. Fill the fuel tank to the bottom filler tube as shown.
EW000130
ARNINGo not overfill the fuel tank, oth-rwise it may overflow when theuel warms up and expands. void spilling fuel on the hotngine.
1. F2. U
l tank filler tubel level
E_5MT.book Page 11 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-11
EAU02935
el tank cap
open the fuel tank capen the fuel tank cap lock cover, in-t the key into the lock, and then turn/4 turn clockwise. The lock will be re-sed and the fuel tank cap can bened.
close the fuel tank capPush the fuel tank cap into posi-tion with the key inserted in thelock. Turn the key counterclockwise tothe original position, remove it,and then close the lock cover.
NOTE:@
The fuel tank cap cannot be closed un-less the key is in the lock. In addition,the key cannot be removed if the cap isnot properly closed and locked. @
EWA00025
WARNING@
Make sure that the fuel tank cap isproperly closed before riding. @
FuelMakethe taof the
W_
� Def
� Ae
_
uel tank cap lock covernlock.
1. Fue2. Fue
NTROL FUNCTIONS
3
C@
Imwfues@
C_
Uusveparinte_
E_5MT.book Page 12 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-12
EAU00185
AUTION:mediately wipe off spilled fuel
ith a clean, dry, soft cloth, sinceel may deteriorate painted surfac- or plastic parts.
EAU04265
ECA00104
AUTION:se only unleaded gasoline. Thee of leaded gasoline will cause se-re damage to internal enginerts, such as the valves and pistongs, as well as to the exhaust sys-
m.
Your Yamaha engine has been de-signed to use regular unleaded gaso-line with a pump octane number[(R+M)/2] of 86 or higher, or a researchoctane number of 91 or higher. Ifknocking (or pinging) occurs, use agasoline of a different brand or premi-um unleaded fuel. Use of unleaded fuelwill extend spark plug life and reducemaintenance costs.
GasoholThere are two types of gasohol: gaso-hol containing ethanol and that contain-ing methanol. Gasohol containingethanol can be used if the ethanol con-tent does not exceed 10%. Gasoholcontaining methanol is not recom-mended by Yamaha because it cancause damage to the fuel system or ve-hicle performance problems.
Recommended fuel:UNLEADED GASOLINE ONLY
Fuel tank capacity:Total amount:
17 L (3.7 Imp gal, 4.5 US gal)Reserve amount:
3.5 L (0.8 Imp gal, 0.9 US gal)
IN
3
StStaair-theMotheMothe
EAU03814
ats
er seat remove the rider seatl up the rear corners of the rider seatshown, remove the bolts, and thenl the seat off.
1. S olt (× 2)
E_5MT.book Page 13 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-13
EAU02973
arter (choke) leverrting a cold engine requires a richerfuel mixture, which is supplied by starter (choke).ve the lever in direction a to turn on starter (choke).ve the lever in direction b to turn off starter (choke).
ECA00038
CAUTION:@
Do not use the starter (choke) formore than 3 minutes as the exhaustpipe may discolor from excessiveheat. In addition, extended use ofthe starter (choke) will cause after-burning. If this occurs, turn off thestarter (choke). @
Se
RidTo Pulas pul
tarter (choke) lever 1. B
NTROL FUNCTIONS
3
ToInridshpo
install the passenger seat. Insert the projection on the rear of
the passenger seat into the seatholder as shown, and then pushthe front of the seat down to lock itin place.
. Remove the key.
TE:ake sure that the seats are properlycured before riding.
1.2.
ProjectionSeat holder
E_5MT.book Page 14 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-14
install the rider seatsert the projection on the front of theer seat into the seat holder asown, place the seat in the originalsition, and then install the bolts.
Passenger seat To remove the passenger seat
1. Insert the key into the seat lock,and then turn it counterclockwise.
2. While holding the key in that posi-tion, lift the front of the passengerseat and pull it forward.
To1
2
NO_
Mse_
ProjectionSeat holder
1. Passenger seat lock2. Unlock.
Left side
1.2.
IN
3
HeThebot
Toer
1.
2.
EAU01242
e compartment rage compartment is located
he passenger seat. (See pager passenger seat opening andprocedures.)
EWA00005
RNING not exceed the load limit ofg (7 lb) for the storage com-rtment. not exceed the maximumd of YZF-R6: 189 kg (417 lb)/F-R6C: 188 kg (415 lb) for thehicle.
1. H e compartment
E_5MT.book Page 15 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-15
EAU03159
lmet holders helmet holders are located on the
tom of the passenger seat.
secure a helmet to a helmet hold-
Remove the passenger seat. (Seepage 3-14 for removal and instal-lation procedures.) Attach the helmet to a helmetholder, and then securely installthe passenger seat.
EWA00015
WARNING_
Never ride with a helmet attached toa helmet holder, since the helmetmay hit objects, causing loss ofcontrol and possibly an accident. _
To release the helmet from a helmetholderRemove the passenger seat, removethe helmet from the helmet holder, andthen install the seat.
StoragThe stounder t3-14 foclosing
WA_
� Do3 kpa
� DoloaYZve
_
elmet holder (× 2) 1. Storag
NTROL FUNCTIONS
3
AThprinprsc
_
Alyof_
0E
Current settingFront fork cap bolt
Setting
Minimum (soft) 8
Standard 7*
Maximum (hard) 1
ore precisely 1 mm below the seventh groove
E_5MT.book Page 16 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-16
EAU04392
djusting the front fork is front fork is equipped with springeload adjusting bolts, rebound damp-g force adjusting screws and com-ession damping force adjustingrews.
EW000035
WARNINGlways adjust both fork legs equal-, otherwise poor handling and loss stability may result.
Spring preloadTo increase the spring preload andthereby harden the suspension, turnthe adjusting bolt on each fork leg in di-rection a. To decrease the spring pre-load and thereby soften thesuspension, turn the adjusting bolt oneach fork leg in direction b.
NOTE:_
Align the appropriate groove on the ad-justing mechanism with the top of thefront fork cap bolt. _
CI-1
1. Spring preload adjusting bolt 1.2.
* m
IN
3
ReTo forcdameaccretheturnlegCI-02
EC000015
UTION:er attempt to turn an adjusting
chanism beyond the maximuminimum settings.
TE:ough the total number of clicks of aping force adjusting mechanism
y not exactly match the above spec-tions due to small differences in
duction, the actual number of clicksays represents the entire adjustingge. To obtain a precise adjustment,ould be advisable to check the num- of clicks of each damping force ad-ing mechanism and to modify thecifications as necessary.
1. R
M
Ma
* Wi
E_5MT.book Page 17 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-17
bound damping forceincrease the rebound damping
e and thereby harden the reboundping, turn the adjusting screw on
h fork leg in direction a. To de-ase the rebound damping force andreby soften the rebound damping, the adjusting screw on each fork
in direction b.E
Compression damping forceTo increase the compression dampingforce and thereby harden the compres-sion damping, turn the adjusting screwon each fork leg in direction a. To de-crease the compression damping forceand thereby soften the compressiondamping, turn the adjusting screw oneach fork leg in direction b.CI-02E
CA_
Nevmeor m_
NO_
Althdammaificaproalwranit wberjustspe_
ebound damping force adjusting screw
inimum (soft) 10 clicks in direction b*
Standard 6 clicks in direction b*
ximum (hard) 1 clicks in direction b*
th the adjusting screw fully turned in direction a
1. Compression damping force adjusting screw
Minimum (soft) 9 clicks in direction b*
Standard 6 clicks in direction b*
Maximum (hard) 1 clicks in direction b*
* With the adjusting screw fully turned in direction a
NTROL FUNCTIONS
3
AasTheqinjuda
C@
Nmor@
bound damping forceincrease the rebound damping
e and thereby harden the reboundping, turn the adjusting knob in di-
tion a. To decrease the reboundping force and thereby soften the
ound damping, turn the adjustingb in direction b.
E
ebound damping force adjusting knob
inimum (soft) 20 clicks in direction b*
Standard 9 clicks in direction b*
ximum (hard) 3 clicks in direction b*
th the adjusting knob fully turned in direction a
E_5MT.book Page 18 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-18
EAU01863
djusting the shock absorber sembly is shock absorber assembly isuipped with a spring preload adjust-
g ring, a rebound damping force ad-sting knob and a compressionmping force adjusting screw.
EC000015
AUTION:ever attempt to turn an adjustingechanism beyond the maximum minimum settings. Spring preload
To increase the spring preload andthereby harden the suspension, turnthe adjusting ring in direction a. To de-crease the spring preload and therebysoften the suspension, turn the adjust-ing ring in direction b.
NOTE:@
Align the appropriate notch in the ad-justing ring with the position indicatoron the shock absorber. @
CI-10E
ReTo forcdamrecdamrebknoCI-03
1. Spring preload adjusting ring2. Special wrench3. Position indicator
Setting
Minimum (soft) 1
Standard 4
Maximum (hard) 9
1. R
M
Ma
* Wi
IN
3
CoTo forcsioin dpresoftheCI-02
EAU00315
WARNINGs shock absorber contains high-pressurized nitrogen gas. Forper handling, read and under-nd the following information be-e handling the shock absorber. manufacturer cannot be held re-nsible for property damage orsonal injury that may result fromroper handling.Do not tamper with or attempt toopen the gas cylinder.Do not subject the shock ab-sorber to an open flame or otherhigh heat sources, otherwise itmay explode due to excessivegas pressure.Do not deform or damage thegas cylinder in any way, as thiswill result in poor damping per-formance.Always have a Yamaha dealerservice the shock absorber.
1. C
M
Ma
* Wi
E_5MT.book Page 19 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-19
mpression damping forceincrease the compression dampinge and thereby harden the compres-
n damping, turn the adjusting screwirection a. To decrease the com-
ssion damping force and therebyten the compression damping, turn adjusting screw in direction b.
E
NOTE:@
Although the total number of clicks of adamping force adjusting mechanismmay not exactly match the above spec-ifications due to small differences inproduction, the actual number of clicksalways represents the entire adjustingrange. To obtain a precise adjustment,it would be advisable to check the num-ber of clicks of each damping force ad-justing mechanism and to modify thespecifications as necessary. @
@
Thily prostaforThespoperimp
�
�
�
�
@
ompression damping force adjusting screw
inimum (soft) 12 clicks in direction b*
Standard 7 clicks in direction b*
ximum (hard) 1 click in direction b*
th the adjusting screw fully turned in direction a
NTROL FUNCTIONS
3
EAU01580
MU nt fork and shock absorber assemblyacCI-
EC000015
C@
N m settings. @
absorber assembly adjustment
Compression damping force
Rebound damping force
4–12 3–20
1–8 3–7
E_5MT.book Page 20 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-20
atching the front and rear suspension settings se this table as a guide to match the suspension and damping adjustments of the frocording to various load conditions.
05E
AUTION:ever attempt to turn an adjusting mechanism beyond the maximum or minimu
Load condition Front fork adjustment Shock
Spring preloadCompression damping force
Rebound damping force
Spring preload
Rider only 1–8 1–9 1–10 1–7
With passenger 1–8 1–9 1–10 4–9
IN
3
LuTheon To pasandhanseaseadur
EW000044
WARNING motorcycle must not be ridden
h the sidestand down, or if theestand cannot be properlyved up (or does not stay up), oth-ise the sidestand could contact ground and distract the opera-, resulting in a possible loss oftrol. Yamaha’s ignition circuit
-off system has been designed toist the operator in fulfilling theponsibility of raising the side-nd before starting off. Therefore,ck this system regularly as de-ibed below and have a Yamahaler repair it if it does not functionperly.
1. L2. H
E_5MT.book Page 21 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-21
EAU03170
ggage strap holders re are four luggage strap holdersthe bottom of the passenger seat.use the strap holders, remove thesenger seat, unhook the straps, then install the seat with the strapsging out from under the passengert. (See page 3-14 for passengert removal and installation proce-es.)
EAU00330
Sidestand The sidestand is located on the left sideof the frame. Raise the sidestand orlower it with your foot while holding themotorcycle upright.
NOTE:@
The built-in sidestand switch is part ofthe ignition circuit cut-off system, whichcuts the ignition in certain situations.(See further down for an explanation ofthe ignition circuit cut-off system.) @
@
Thewitsidmoerwthetorconcutassresstachescrdeapro@
uggage strap holder (× 4)ook (× 4)
NTROL FUNCTIONS
3
IgThprswlo
Peigto
_
If Yabe_
E_5MT.book Page 22 Tuesday, August 28, 2001 2:05 PM
INSTRUMENT AND CO
3-22
EAU03720
nition circuit cut-off system e ignition circuit cut-off system (com-ising the sidestand switch, clutchitch and neutral switch) has the fol-
wing functions.� It prevents starting when the trans-
mission is in gear and the side-stand is up, but the clutch lever isnot pulled.
� It prevents starting when the trans-mission is in gear and the clutchlever is pulled, but the sidestand isstill down.
� It cuts the running engine whenthe transmission is in gear and thesidestand is moved down.
riodically check the operation of thenition circuit cut-off system according the following procedure.
EW000045
WARNINGa malfunction is noted, have amaha dealer check the systemfore riding.
IN
3
CD-0
itch may be defective.le should not be ridden until
Yamaha dealer.
switch may be defective.le should not be ridden until
Yamaha dealer.
itch may be defective.le should not be ridden until
Yamaha dealer.
ost reliable if performed withengine.
E_5MT.book Page 23 Tuesday, August 28, 2001 2:05 PM
STRUMENT AND CONTROL FUNCTIONS
3-23
1E
With the engine turned off:1. Move the sidestand down.2. Make sure that the engine stop switch is set to “ ”.3. Turn the key to “ON”. 4. Shift the transmission into the neutral position.5. Push the start switch.Does the engine start?
The neutral swThe motorcycchecked by a
With the engine still running:6. Move the sidestand up.7. Keep the clutch lever pulled.8. Shift the transmission into gear.9. Move the sidestand down.Does the engine stall?
After the engine has stalled:10. Move the sidestand up.11. Keep the clutch lever pulled.12. Push the start switch.Does the engine start?
The sidestandThe motorcycchecked by a
The clutch swThe motorcycchecked by a
NO
NOTE:This check is ma warmed-up
YES
YES NO
The system is OK. The motorcycle can be ridden.
YES NO
PRE-OPERATION CHECKS
4
Pre-operation check list ..................................................................... 4-1
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
4
EAU01114
teriorate quickly and unexpectedly,). Any damage, fluid leakage or lossddition to a thorough visual inspec-
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
4-PR
Theeveof ti
EAU03439
PAGE
3-11–3-12
6-11–6-12
6-15–6-16
6-29–6-31
6-28–6-31
6-27, 6-34
tion
CO-01E
Fu
En
Co
Fro
Re
Clu
4-1
E-OPERATION CHECKS
condition of a vehicle is the owner’s responsibility. Vital components can start to den if the vehicle remains unused (for example, as a result of exposure to the elementsre air pressure could have serious consequences. Therefore, it is very important, in a, to check the following points before each ride.
Pre-operation check list
ITEM CHECKS
el• Check fuel level in fuel tank.• Refuel if necessary.• Check fuel line for leakage.
gine oil• Check oil level in engine.• If necessary, add recommended oil to specified level.• Check vehicle for oil leakage.
olant• Check coolant level in reservoir.• If necessary, add recommended coolant to specified level.• Check cooling system for leakage.
nt brake
• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.
ar brake
• Check operation.• If soft or spongy, have Yamaha dealer bleed hydraulic system.• Check fluid level in reservoir.• If necessary, add recommended brake fluid to specified level.• Check hydraulic system for leakage.
tch
• Check operation.• Lubricate cable if necessary.• Check lever free play.• Adjust if necessary.
PERATION CHECKS
4
T 6-22, 6-34
C 6-34
D 6-31–6-32
W 6-23–6-26
B 6-35
B 6-34
S 6-35
C —
Ina —
S 3-21
A 6-21
PAGE
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
PRE-O
4-2
hrottle grip• Make sure that operation is smooth.• Check free play.• If necessary, have Yamaha dealer make adjustment or lubricate.
ontrol cables • Make sure that operation is smooth.• Lubricate if necessary.
rive chain
• Check chain slack.• Adjust if necessary.• Check chain condition.• Lubricate if necessary.
heels and tires
• Check for damage.• Check tire condition and tread depth.• Check air pressure.• Correct if necessary.
rake and shift pedals • Make sure that operation is smooth.• Lubricate pedal pivoting points if necessary.
rake and clutch levers • Make sure that operation is smooth.• Lubricate lever pivoting points if necessary.
idestand • Make sure that operation is smooth.• Lubricate pivot if necessary.
hassis fasteners • Make sure that all nuts, bolts and screws are properly tightened.• Tighten if necessary.
struments, lights, signals nd switches
• Check operation. • Correct if necessary.
idestand switch • Check operation of ignition circuit cut-off system.• If system is defective, have Yamaha dealer check vehicle.
ir intake duct • Check that the screen is not clogged.• Clean if necessary.
ITEM CHECKS
PR
4
NO@
Pre ction can be accomplished in a verysho@
EWA00033
@
If a ed and repaired before operatingthe@
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
E-OPERATION CHECKS
4-3
TE:-operation checks should be made each time the motorcycle is used. Such an inspert time; and the added safety it assures is more than worth the time involved.
WARNINGny item in the Pre-operation check list is not working properly, have it inspect motorcycle.
OPERATION AND IMPORTANT RIDING POINTS
5
Starting and warming up a cold engine ............................................. 5-1Starting a warm engine ..................................................................... 5-2Shifting .............................................................................................. 5-3Engine break-in ................................................................................. 5-5Parking .............................................................................................. 5-5
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
5
EAU00372
Turn the key to “ON” and makesure that the engine stop switch isset to “ ”.
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
5-OP
@
�
ECA00005*
UTION: oil level/coolant temperature
rning light and fuel level warningt should come on for a few sec-s, then go off. If a warning lights not go off, see pages 3-2 and 3-3the corresponding warning lightuit check.
Shift the transmission into the neu-tral position.
TE:en the transmission is in the neutralition, the neutral indicator lightuld be on, otherwise have aaha dealer check the electrical cir-
.
Turn the starter (choke) on andcompletely close the throttle. (Seepage 3-13 for starter (choke) oper-ation.)
�
�
@
5-1
ERATION AND IMPORTANT RIDING POINTSEAU00373
WARNINGBecome thoroughly familiarwith all operating controls andtheir functions before riding.Consult a Yamaha dealer re-garding any control or functionthat you do not thoroughly un-derstand.Never start the engine or oper-ate it in a closed area for anylength of time. Exhaust fumesare poisonous, and inhalingthem can cause loss of con-sciousness and death within ashort time. Always make surethat there is adequate ventila-tion.Before starting out, make surethat the sidestand is up. If thesidestand is not raised com-pletely, it could contact theground and distract the opera-tor, resulting in a possible lossof control.
EAU01361*
Starting and warming up a cold engine In order for the ignition circuit cut-offsystem to enable starting, one of thefollowing conditions must be met:
� The transmission is in the neutralposition.
� The transmission is in gear withthe clutch lever pulled and thesidestand up.
EW000054
WARNING@
� Before starting the engine,check the function of the igni-tion circuit cut-off system ac-cording to the proceduredescribed on page 3-23.
� Never ride with the sidestanddown.
@
1.
CA@
Thewalighonddoefor circ@
2.
NO@
WhposshoYamcuit@
3.
ANT RIDING POINTS
5
4
N@
If stthshsegiat@
5
C@
Fowofen@
6
EAU01258
tarting a warm engine llow the same procedure as for start- a cold engine with the exception
at the starter (choke) is not requireden the engine is warm.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
OPERATION AND IMPORT
5-2
. Start the engine by pushing thestart switch.
OTE:the engine fails to start, release theart switch, wait a few seconds, anden try again. Each starting attemptould be as short as possible to pre-rve the battery. Do not crank the en-
ne more than 10 seconds on any onetempt.
. After starting the engine, move thestarter (choke) lever back halfway.
ECA00055
AUTION:r maximum engine life, always
arm the engine up before startingf. Never accelerate hard when thegine is cold!
. When the engine is warm, turn thestarter (choke) off.
NOTE:@
The engine is warm when it respondsnormally to the throttle with the starter(choke) turned off. To avoid the possi-bility of excessive exhaust emissions,never leave the starter (choke) on long-er than necessary. The time necessaryfor starter (choke) use depends uponthe ambient temperature. Tempera-tures above 50 °F (10 °C) require about10 seconds of starter (choke) use andtemperatures below 50 °F (10 °C) re-quire about 3.5 seconds with the starter(choke) turned on, then about 2.5 min-utes with the starter (choke) in the half-way position. @
SFoingthwh
O
5 ShShamstaetcThelus
NO@
To tralreptrav@
EAU02988
start out and accelerate Pull the clutch lever to disengagethe clutch.Shift the transmission into firstgear. The neutral indicator lightshould go out.Open the throttle gradually, and atthe same time, release the clutchlever slowly.At the recommended shift pointsshown in the table on page 5-4,close the throttle, and at the sametime, quickly pull the clutch leverin.Shift the transmission into secondgear. (Make sure not to shift thetransmission into the neutral posi-tion.)Open the throttle part way andgradually release the clutch lever.Follow the same procedure whenshifting to the next higher gear.
TE:ays shift gears at the recommend-shift points.
1. SN. N
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
PERATION AND IMPORTANT RIDING POINTS
5-3
EAU00423
ifting ifting gears lets you control theount of engine power available forrting off, accelerating, climbing hills,. gear positions are shown in the il-
tration.
TE:shift the transmission into the neu- position, press the shift pedal downeatedly until it reaches the end of itsel, and then slightly raise it.
EC000048
CAUTION:@
� Even with the transmission inthe neutral position, do notcoast for long periods of timewith the engine off, and do nottow the motorcycle for long dis-tances. The transmission isproperly lubricated only whenthe engine is running. Inade-quate lubrication may damagethe transmission.
� Always use the clutch whilechanging gears to avoid dam-aging the engine, transmission,and drive train, which are notdesigned to withstand theshock of forced shifting.
@
To 1.
2.
3.
4.
5.
6.
7.
NO@
Alwed @
hift pedaleutral position
ANT RIDING POINTS
5
To1
2
3
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
OPERATION AND IMPORT
5-4
EAU00427
decelerate . Apply both the front and the rear
brakes to slow the motorcycle.. Shift the transmission into first
gear when the motorcycle reaches25 km/h (15.5 mi/h). If the engineis about to stall or runs very rough-ly, pull the clutch lever in and usethe brakes to stop the motorcycle.
. Shift the transmission into the neu-tral position when the motorcycleis almost completely stopped. Theneutral indicator light should comeon.
EAU02989
Recommended shift points The recommended shift points duringacceleration and deceleration areshown in the table below.CF-05E
Accelerationshift point
km/h (mi/h)
Decelerationshift point
km/h (mi/h)
1st → 2nd2nd → 3rd3rd → 4th4th → 5th5th → 6th
16 (9.9)24 (14.9)32 (19.9)40 (24.9)48 (29.8)
–25 (15.5)25 (15.5)25 (15.5)25 (15.5)
O
5
EnThein tbetForfollSinput1,6in selancfullthamu
EAU00460
king n parking, stop the engine, and remove the key from the mainch.
EW000058
WARNINGSince the engine and exhaustsystem can become very hot,park in a place where pedestri-ans or children are not likely totouch them. Do not park on a slope or onsoft ground, otherwise themotorcycle may overturn.
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
PERATION AND IMPORTANT RIDING POINTS
5-5
EAU01128
gine break-in re is never a more important period
he life of your engine than the periodween 0 and 1,600 km (1,000 mi). this reason, you should read theowing material carefully.ce the engine is brand new, do not an excessive load on it for the first00 km (1,000 mi). The various partsthe engine wear and polish them-ves to the correct operating clear-es. During this period, prolonged
-throttle operation or any conditiont might result in engine overheatingst be avoided.
EAU03749*
0–1,000 km (0–600 mi)Avoid prolonged operation above5,000 r/min.
1,000–1,600 km (600–1,000 mi)Avoid prolonged operation above6,000 r/min.
EC000052*
CAUTION:_
After 1,000 km (600 mi) of operation,the engine oil must be changed andthe oil filter cartridge replaced. _
1,600 km (1,000 mi) and beyondThe vehicle can now be operated nor-mally.
EC000053
CAUTION:_
� Keep the engine speed out ofthe tachometer red zone.
� If any engine trouble should oc-cur during the engine break-inperiod, immediately have aYamaha dealer check the vehi-cle.
_
ParWhethenswit
@
�
�
@
6
PERIODIC MAINTENANCE AND MINOR REPAIR
Periodic maintenance ..........................................6-1Owner’s tool kit ....................................................6-1Periodic maintenance chart for the emission
control system ...................................................6-3General maintenance and lubrication chart .........6-4Removing and installing the cowlings
and panel ...........................................................6-7Checking the spark plugs ....................................6-9Canister (for California only) ..............................6-11Engine oil and oil filter cartridge ........................6-11Coolant ..............................................................6-15Checking the air filter element ...........................6-19Air intake duct ....................................................6-21Adjusting the carburetors ...................................6-22Adjusting the throttle cable free play ..................6-22Adjusting the valve clearance ............................6-22Tires ...................................................................6-23Cast wheels .......................................................6-26Accessories and replacement parts ..................6-26Adjusting the clutch lever free play ....................6-27Adjusting the brake pedal position .....................6-28Adjusting the rear brake light switch ..................6-28Checking the front and rear brake pads .............6-29Checking the brake fluid level ............................6-30
Changing the brake fluid ................................... 6-31Drive chain slack ............................................... 6-31Lubricating the drive chain ................................ 6-33Checking and lubricating the cables ................. 6-34Checking and lubricating the throttle
grip and cable ................................................. 6-34Checking and lubricating the brake and
clutch levers .................................................... 6-34Checking and lubricating the brake and
shift pedals ...................................................... 6-35Checking and lubricating the sidestand ............ 6-35Lubricating the rear suspension ........................ 6-36Checking the front fork ...................................... 6-36Checking the steering ....................................... 6-37Checking the wheel bearings ............................ 6-37Battery ............................................................... 6-38Replacing the fuses .......................................... 6-39Replacing a headlight bulb ................................ 6-41Tail/brake light ................................................... 6-42Replacing a turn signal light bulb ...................... 6-42Supporting the motorcycle ................................ 6-43Front wheel ....................................................... 6-43Rear wheel ........................................................ 6-45Troubleshooting ................................................. 6-46Troubleshooting charts ...................................... 6-47
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
6
EAU00462
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
6-PE
SafPer
EAU04266
ner’s tool kit owner’s tool kit is located inside
storage compartment under thesenger seat. (See page 3-14 forsenger seat removal and installa- procedures.) service information included in this
nual and the tools provided in theer’s tool kit are intended to assist in the performance of preventiveintenance and minor repairs. How-r, additional tools such as a torquench may be necessary to performtain maintenance work correctly.
wner’s tool kit
bricsafesiblmolubring Maof tsysreptha
@
If ycycYam@
6-1
RIODIC MAINTENANCE AND MINOR REPAIR EAU01790
ety is an obligation of the owner.iodic inspection, adjustment and lu-ation will keep your vehicle in thest and most efficient condition pos-
e. The most important points oftorcycle inspection, adjustment, andication are explained on the follow-pages.intenance, replacement, or repairhe emission control devices andtems may be performed by anyair establishment or individualt is certified (if applicable).
EW000060
WARNINGou are not familiar with motor-le maintenance work, have aaha dealer do it for you.
EAU00467
PERIODIC MAINTENANCE PROPER PERIODIC MAINTENANCEOF YOUR MOTORCYCLE IS IMPOR-TANT IN ORDER TO ENJOY LONG,PLEASURABLE SERVICE. ESPE-CIALLY IMPORTANT ARE THEMAINTENANCE SERVICES RELAT-ED TO EMISSIONS CONTROL.THESE CONTROLS NOT ONLYFUNCTION TO ENSURE CLEANERAIR, BUT ARE ALSO VITAL TOPROPER ENGINE OPERATION ANDMAXIMUM PERFORMANCE. IN THEFOLLOWING PERIODIC MAINTE-NANCE CHARTS, THE SERVICESRELATED TO EMISSIONS CON-TROL ARE GROUPED SEPARATE-LY. THESE SERVICES REQUIRESPECIALIZED DATA, KNOWLEDGE,AND EQUIPMENT. YAMAHA DEAL-ERS ARE TRAINED AND EQUIPPEDTO PERFORM THESE PARTICULARSERVICES.
OwThethepaspastionThemaownyoumaevewrecer
1. O
AND MINOR REPAIR
6
N_
If ena _
_
MYamreCte_
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-2
OTE:you do not have the tools or experi-ce required for a particular job, have
Yamaha dealer perform it for you.
EW000062
WARNINGodifications not approved bymaha may cause loss of perfor-
ance, excessive emissions, andnder the vehicle unsafe for use.onsult a Yamaha dealer before at-mpting any changes.
PE
6
EAU00471
l system
* S** C
No
METER READINGS12,000 mi
(19,000 km)or
18 months
16,000 mi(25,000 km)
or24 months
20,000 mi(31,000 km)
or30 months
1 mi (42,000 km)
2 √ Replace. √
3 √ √ √
4 √ √ √
5 Replace.
6 √ √ √
7 √ √ √
8 √ √ √
9 √
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-3
Periodic maintenance chart for the emission contro
ince these items require special tools, data and technical skills, have a Yamaha dealer perform the service.alifornia only
. ITEM ROUTINE
INITIAL ODO600 mi
(1,000 km)or
1 month
4,000mi(7,000 km)
or6 months
8,000 mi(13,000 km)
or12 months
* Valve clearance • Check and adjust valve clearance when engine is cold. Every 26,600
Spark plugs
• Check condition. • Adjust gap and clean. • Replace every 8,000 mi (13,000 km)
or 12 months.
√ Replace.
*Crankcase ventilation system
• Check ventilation hose for cracks or damage.
• Replace if necessary.√ √
* Fuel line• Check fuel hoses for cracks or
damage.• Replace if necessary.
√ √
* Fuel filter • Replace every 20,000 mi (31,000 km) or 30 months.
* Exhaust system• Check for leakage. • Tighten if necessary. • Replace gasket(s) if necessary.
√ √
*Carburetor synchronization • Adjust synchronization of carburetors. √ √ √
* Idle speed • Check and adjust engine idle speed. • Adjust cable free play. √ √
*Evaporative emission control system**
• Check control system for damage. • Replace if necessary.
ND MINOR REPAIR
6
EAU00472
N
METER READINGS
)12,000 mi
(19,000 km)or
18 months
16,000 mi(25,000 km)
or24 months
20,000 mi(31,000 km)
or30 months
1 √ √ √
2 √
3 √ √ √
4√ √ √
Replace.
5 √ √ √
6 √ √ √
7 √ √ √
8 √
* .
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE A
6-4
General maintenance and lubrication chart
o. ITEM ROUTINE
INITIAL ODO600 mi
(1,000 km)or
1 month
4,000mi(7,000 km)
or6 months
8,000 mi(13,000 km
or12 months
Engine oil• Replace (warm engine before
draining). (See NOTE on page 8-1.)√ √ √
*Engine oil filter cartridge
• Replace at initial 600 mi (1,000 km) or 1 month, and thereafter every 8,000 mi (13,000 km) or 12 months.
√ √
* Air filter element• Check condition and damage.• Replace if necessary.
√ √
* Cooling system
• Check hose for cracks or damage.• Replace if necessary.
√ √
• Replace coolant every 24 months.• Ethylene glycol anti-freeze coolant.
* Brake system• Check operation, pad wear, and fluid
leakage. (See NOTE on page 6-6.)• Correct if necessary.
√ √ √
* Clutch• Check operation.• Adjust or replace cable.
√ √ √
* Control cable• Apply chain lube thoroughly.• Yamaha chain and cable lube or
SAE10W30 motor oil.√ √ √
*Swing arm pivot bearing
• Check bearing assembly for looseness.
√
Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service
PE
6
9 √
10 √ √ √
11 √ √ √
12 √ √Repack. √
13 √ √ √
14 √ √ √
15or after washing the motorcycle g in the rain.
16 √ √ √
No
OMETER READINGSim)
hs
12,000 mi(19,000 km)
or18 months
16,000 mi(25,000 km)
or24 months
20,000 mi(31,000 km)
or30 months
* S e.
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-5
*Rear suspension link pivots
• Check operation.• Apply grease lightly every 16,000 mi
(25,000 km) or 24 months.• Lithium-soap-based grease • Correct if necessary.
√
*Shock absorber assembly
• Check operation and for oil leakage.• Replace if necessary.
√ √
* Front fork• Check operation and oil leakage.• Replace if necessary.
√ √
* Steering bearings
• Check bearing assembly for looseness.
• Moderately repack every 16,000 mi (25,000 km) or 24 months.
• Lithium-soap-based grease
√ √
Brake and clutch lever pivot shafts
• Apply chain lube lightly.• Lithium-soap-based grease
(all-purpose grease)√ √
Brake and shift pedal pivot shafts
• Apply chain lube lightly.• Lithium-soap-based grease
(all-purpose grease)√ √
* Drive chain
• Check chain slack/alignment condition.
• Adjust and lubricate chain thoroughly.• Special O-ring chain lubricant.
Every 600 mi (1,000 km) or ridin
* Wheel bearings • Check bearings for smooth operation. √ √
. ITEM ROUTINE
INITIAL OD600 mi
(1,000 km)or
1 month
4,000mi(7,000 km)
or6 months
8,000 m(13,000 k
or12 mont
ince these items require special tools, data and technical skills, have a Yamaha dealer perform the servic
AND MINOR REPAIR
6
EAU03907
N_
Fr om 4,000 mi (7,000 km) or 6 months. _
EAU04249
N_
y areas.
fluid. Regularly check the brake fluid
and calipers, and change the brake
_
17 √ √ √
18 √ √ √
19 √ √ √
N
DOMETER READINGSmi km)
ths
12,000 mi(19,000 km)
or18 months
16,000 mi(25,000 km)
or24 months
20,000 mi(31,000 km)
or30 months
* ice.
E_5MT.book Page 6 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-6
OTE:om 24,000 mi (37,000 km) or 36 months, repeat the maintenance intervals starting fr
OTE:� The air filter needs more frequent service if you are riding in unusually wet or dust� Hydraulic brake service
• After disassembling the brake master cylinders and calipers, always change thelevels and fill the reservoirs as required.
• Every two years replace the internal components of the brake master cylindersfluid.
• Replace the brake hoses every four years and if cracked or damaged.
* Sidestand pivot
• Check operation and lubricate.• Apply chain lube lightly.• Lithium-soap-based grease
(all-purpose grease)
√ √
* Sidestand switch• Check and clean or replace if
necessary.√ √ √
* Chassis fasteners• Check all chassis fitting and fasteners.• Correct if necessary.
√ √
o. ITEM ROUTINE
INITIAL O600 mi
(1,000 km)or
1 month
4,000mi(7,000 km)
or6 months
8,000 (13,000
or12 mon
Since these items require special tools, data and technical skills, have a Yamaha dealer perform the serv
PE
6
RecoTheneeof thistimrem
1. CC
2. P
crew (× 6)owling B
ft side
E_5MT.book Page 7 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-7
EAU03624
moving and installing the wlings and panel cowlings and panel shown aboved to be removed to perform some
the maintenance jobs described in chapter. Refer to this section eache a cowling or the panel needs to beoved and installed.
EAU01602
Cowlings A and BTo remove one of the cowlingsRemove the screws, slide the cowlingforward (for A) or backward (for B), andthen pull it off as shown.
owling A (right side) owling B (left side)anel A
1. Screw (× 5)2. Cowling A
Right side
1. S2. C
Le
AND MINOR REPAIR
6
. Place the cowling in the originalposition, and then install thescrews.
TE:ake sure that the tabs at the front ofch cowling fit side by side as shownd that all slots and projections fit to-ther.
1.2.
Tab (× 2)
E_5MT.book Page 8 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-8
To install the cowling1. Fit the slots and projections at the
rear bottom of each cowling to-gether, and then slide the cowlinginto place.
2
NO@
Meaange@]
Cowling ACowling B
1. Slot (× 2)2. Projection (× 2)
1.
PE
6
PaTo Repan
EAU01639
ecking the spark plugs spark plugs are important engineponents, which should be checked
iodically, preferably by a Yamahaler. Since heat and deposits willse any spark plug to slowly erode,y should be removed and checkedccordance with the periodic mainte-ce and lubrication chart. In addition,
condition of the spark plugs can re-l the condition of the engine. porcelain insulator around the cen-
electrode of each spark plug shoulda medium-to-light tan (the ideal col-
hen the motorcycle is ridden nor-lly), and all spark plugs installed in engine should have the same color.ny spark plug shows a distinctly dif-nt color, the engine could be defec-. Do not attempt to diagnose suchblems yourself. Instead, have a
aha dealer check the motorcycle.
1. S
E_5MT.book Page 9 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-9
EAU01315
nel Aremove the panelmove the screws, and then take theel off.
To install the panelPlace the panel in the original position,and then install the screws.
ChThecomperdeacauthein anantheveaTheter be or wmatheIf aferetiveproYam
crew (× 2) 1. Projection2. Slot
AND MINOR REPAIR
6
If erde
TE: torque wrench is not available whentalling a spark plug, a good estimate
the correct torque is 1/4–1/2 turnst finger tight. However, the sparkg should be tightened to the speci-
d torque as soon as possible.
ECA00021
AUTION: not use any tools to remove or
stall the spark plug cap, otherwisee ignition coil coupler may getmaged. The spark plug cap may difficult to remove because thebber seal on the end of the cap fitshtly. To remove the spark plugp, simply twist it back and forth
hile pulling it out; to install it, twistback and forth while pushing it in.
Tightening torque:Spark plug:
12.5 Nm (1.25 m·kgf, 9.0 ft·lb)
E_5MT.book Page 10 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-10
a spark plug shows signs of electrodeosion and excessive carbon or otherposits, it should be replaced.
Before installing a spark plug, the sparkplug gap should be measured with awire thickness gauge and, if necessary,adjusted to specification.
Clean the surface of the spark pluggasket and its mating surface, and thenwipe off any grime from the spark plugthreads.
NO@
If ainsofpaplufie@
C@
Dointhdaberutigcawit @
Specified spark plug:CR10EK (NGK)
For CaliforniaCR9EK (NGK)
a. Spark plug gap
Spark plug gap:0.6–0.7 mm (0.02–0.03 in)
PE
6
EAU04371
gine oil and oil filter rtridge engine oil level should be checked
ore each ride. In addition, the oilst be changed and the oil filter car-ge replaced at the intervals speci- in the periodic maintenance andrication chart.
check the engine oil levelPlace the motorcycle on a levelsurface and hold it in an uprightposition.
TE:ke sure that the motorcycle is posi-ed straight up when checking the oill. A slight tilt to the side can result inlse reading.
1. C2. F3. C
E_5MT.book Page 11 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-11
EAU00499
Canister (for California only) This model is equipped with a canisterto prevent the discharging of fuel vaporinto the atmosphere. Before operatingthis motorcycle, make sure to checkthe following:
� Check each hose connection.� Check each hose and canister for
cracks or damage. Replace ifdamaged.
� Make sure that the canisterbreather is not blocked, and if nec-essary, clean it.
EncaThebefmutridfiedlub
To 1.
NO_
Mationlevea fa_
anisteruel tankanister breather
AND MINOR REPAIR
6
2
3
4
change the engine oil (with orithout oil filter cartridge replace-ent). Remove cowlings A and B. (See
page 6-7 for cowling removal andinstallation procedures.)
. Start the engine, warm it up forseveral minutes, and then turn itoff.
. Place an oil pan under the engineto collect the used oil.
1.
R
Engine oil filler cap
ight side
E_5MT.book Page 12 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-12
. Start the engine, warm it up forseveral minutes, and then turn itoff.
. Wait a few minutes until the oil set-tles.
. Remove the engine oil dipstickand wipe it clean, insert it back intothe hole (without screwing it in),and then remove it again to checkthe oil level.
NOTE:_
The engine oil should be between theminimum and maximum level marks. _
5. If the engine oil is below the mini-mum level mark, remove the oil fill-er cap, and then add sufficient oilof the recommended type to raiseit to the correct level.
6. Insert and tighten the engine oildipstick, and then install and tight-en the oil filler cap.
Towm
1
2
3
Engine oil dipstick
ight side
1. Maximum level mark2. Minimum level mark
1.
R
PE
6
4.
NO_
Skinot_
Apply a thin coat of engine oil tothe O-ring of the new oil filter car-tridge.
TE:ke sure that the O-ring is properlyted.
1. E
L
-ring
E_5MT.book Page 13 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-13
Remove the engine oil filler capand drain bolt to drain the oil fromthe crankcase.
TE:p steps 5–7 if the oil filter cartridge is being replaced.
5. Remove the oil filter cartridge withan oil filter wrench.
NOTE:_
An oil filter wrench is available at aYamaha dealer. _
6.
NO_
Masea_
ngine oil drain bolt
eft side
1. Oil filter wrench2. Oil filter cartridge
Left side
1. O
AND MINOR REPAIR
6
7
8
ECA00105
AUTION:� In order to prevent clutch slip-
page (since the engine oil alsolubricates the clutch), do notmix any chemical additives withthe oil or use oils of grade “CD”or higher. In addition, do notuse oils labeled “ENERGY CON-SERVING II” or higher.
� Make sure that no foreign mate-rial enters the crankcase.
. Start the engine, and then let it idlefor several minutes while checkingit for oil leakage. If oil is leaking,immediately turn the engine offand check for the cause.
TE:ter the engine is started, the engine level warning light should go off if the level is sufficient.
1.
L
E_5MT.book Page 14 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-14
. Install the new oil filter cartridgewith an oil filter wrench, and thentighten it to the specified torquewith a torque wrench.
. Install the engine oil drain bolt, andthen tighten it to the specifiedtorque.
9. Add the specified amount of therecommended engine oil, andthen install and tighten the oil fillercap.
C_
_
10
NO_
Afoiloil_
Torque wrench
Tightening torque:Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lb)
Tightening torque:Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lb)
eft side
Recommended engine oil:See page 8-1.
Oil quantity:Without oil filter cartridge replacement:
2.5 L (2.2 Imp qt, 2.6 US qt)With oil filter cartridge replacement:
2.7 L (2.4 Imp qt, 2.9 US qt)Total amount (dry engine):
3.5 L (3.1 Imp qt, 3.7 US qt)
PE
6
CA_
If tor enger _
11.
12.
eck the coolant level in theolant reservoir.
oolant should be between them and maximum level marks.
um level markum level mark
ide
E_5MT.book Page 15 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-15
EC000067
UTION:he oil level warning light flickersremains on, immediately turn theine off and have a Yamaha deal-
check the vehicle.
Turn the engine off, and thencheck the oil level and correct it ifnecessary.Install the cowlings.
EAU04393
Coolant The coolant level should be checkedbefore each ride. In addition, the cool-ant must be changed at the intervalsspecified in the periodic maintenanceand lubrication chart.
To check the coolant level 1. Place the motorcycle on a level
surface and hold it in an uprightposition.
NOTE:_
� The coolant level must be checkedon a cold engine since the levelvaries with engine temperature.
� Make sure that the motorcycle ispositioned straight up whenchecking the coolant level. A slighttilt to the side can result in a falsereading.
_
2. Chco
NOTE:_
The cminimu_
1. Maxim2. Minim
Left s
AND MINOR REPAIR
6
3
. Close the reservoir cap, and theninstall the coolant reservoir coverby installing the screws.
TE:� The radiator fan is automatically
switched on or off according to thecoolant temperature in the radia-tor.
� If the engine overheats, see page6-48 for further instructions.
1.
L
E_5MT.book Page 16 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-16
. If the coolant is at or below theminimum level mark, remove thecoolant reservoir cover by remov-ing the screws, open the reservoircap, and then add coolant to themaximum level mark.
EC000080
CAUTION:_
� If coolant is not available, usedistilled water or soft tap waterinstead. Do not use hard wateror salt water since it is harmfulto the engine.
� If water has been used insteadof coolant, replace it with cool-ant as soon as possible, other-wise the engine may not besufficiently cooled and the cool-ing system will not be protectedagainst frost and corrosion.
� If water has been added to thecoolant, have a Yamaha dealercheck the antifreeze content ofthe coolant as soon as possible,otherwise the effectiveness ofthe coolant will be reduced.
_
EW000067
WARNING_
Never attempt to remove the radia-tor cap when the engine is hot. _
4
NO_
_
Screw (× 2)
Coolant reservoir capacity:0.44 L (0.39 Imp qt, 0.47 US qt)
eft side
PE
6
To1.
2.
3.
4.
_
Netor_
TE:ck the washer for damage and re-
ce it if necessary.
1. R
R
ightening torque:Coolant drain bolt:
10 Nm (1.0 m·kgf, 7.3 ft·lb)
E_5MT.book Page 17 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-17
EAU04394
change the coolantPlace the motorcycle on a levelsurface and let the engine cool ifnecessary.Remove panel A, and cowlings Aand B. (See pages 6-7 and 6-9 forpanel and cowling removal and in-stallation procedures.)Place a container under the en-gine to collect the used coolant.Remove the radiator cap.
EW000067
WARNINGver attempt to remove the radia- cap when the engine is hot.
5. Remove the coolant drain bolt todrain the engine.
6. Loosen the clamp screw, and thendisconnect the radiator hose todrain the radiator.
7. After the coolant is completelydrained, thoroughly flush the cool-ing system with clean tap water.
8. Connect the radiator hose, andthen tighten the clamp screw.
9. Install the coolant drain bolt, andthen tighten it to the specifiedtorque.
NO_
Chepla_
adiator cap
ight side
1. Coolant drain bolt2. Clamp screw
Right side
T
AND MINOR REPAIR
6
10
. Pour the recommended coolantinto the radiator until it is full.
1.
L
Antifreeze/water mixture ratio:1:1
Recommended antifreeze:High-quality ethylene glycol anti-freeze containing corrosion inhib-itors for aluminum engines
Coolant quantity:Total amount:2.15 L (1.89 Imp qt, 2.27 US qt)
Coolant reservoir capacity:0.44 L (0.39 Imp qt, 0.47 US qt)
E_5MT.book Page 18 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-18
. Remove the coolant reservoir cov-er by removing the screws.
11. 11.Remove the coolant reservoirby removing the bolts.
12. Remove the coolant reservoir cap,and then turn the reservoir upside-down to empty it.
13. Install the coolant reservoir by in-stalling the bolts.
14. Pour the recommended coolantinto the reservoir to the maximumlevel mark, and then install the capand cover.
15
Screw (× 2)
eft side
1. Bolt (× 2)
Left side
PE
6
CA_
�
�
�
_
EAU04395*
ecking the air filter element air filter element should becked at the intervals specified in theiodic maintenance and lubricationrt. Check the air filter element moreuently if you are riding in unusually or dusty areas.Remove the rider seat. (See page3-13 for rider seat removal and in-stallation procedures.)Remove the fuel tank bolts andslightly lift the fuel tank.
olt (× 2)
E_5MT.book Page 19 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-19
EC000080
UTION:If coolant is not available, usedistilled water or soft tap waterinstead. Do not use hard wateror salt water since it is harmfulto the engine. If water has been used insteadof coolant, replace it with cool-ant as soon as possible, other-wise the engine may not besufficiently cooled and the cool-ing system will not be protectedagainst frost and corrosion. If water has been added to thecoolant, have a Yamaha dealercheck the antifreeze content ofthe coolant as soon as possible,otherwise the effectiveness ofthe coolant will be reduced.
16. Install the radiator cap, start theengine, let it idle for several min-utes, and then turn it off.
17. Remove the radiator cap to checkthe coolant level in the radiator. Ifnecessary, add sufficient coolantuntil it reaches the top of the radia-tor, and then install the radiatorcap.
18. Start the engine, and then checkthe vehicle for coolant leakage. Ifcoolant is leaking, have a Yamahadealer check the cooling system.
19. Install the panel and the cowlings.
ChThecheperchafreqwet
1.
2.
1. B
AND MINOR REPAIR
6
3
NBetoth_
. Remove the air filter case cover byremoving the screws.
1.2.3.
Screw (× 6)Air filter case cover
E_5MT.book Page 20 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-20
. Turn the fuel cock lever to “OFF”,and then disconnect the hosesand the fuel sender coupler.
OTE:fore removing the hoses, mark them
ensure that they will be reinstalled ineir correct positions.
4. Tilt the front of the fuel tank back toposition the tank away from the airfilter case, and then support thetank as shown.
5
Fuel cockHose (× 2)Fuel sender coupler
1.2.
PE
6
6.7.
8.
CA_
�
�
_
EAU01335
intake duct ck that the screen of the intaket is not blocked. Clean the screen ifessary.
1. A ir intake duct
E_5MT.book Page 21 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-21
Pull the air filter element out.Check the condition of the air filterelement and replace it if it is dam-aged or excessively dusty.Insert the element into the air filtercase.
EC000082*
UTION:Make sure that the air filter ele-ment is properly seated in theair filter case.The engine should never be op-erated without the air filter ele-ment installed, otherwise thepistons and/or cylinders maybecome excessively worn.
9. Install the air filter case cover byinstalling the screws.
10. Connect the fuel sender couplerand the hoses, turn the fuel cocklever to “ON”, place the fuel tank inthe original position, and then in-stall the bolts.
EW000072
WARNING_
� Before installing the fuel tank,make sure that the fuel hosesare not damaged. If any fuelhose is damaged, do not startthe engine but have a Yamahadealer replace the hose, other-wise fuel may leak.
� Make sure that the fuel hosesare properly connected androuted, and not pinched.
_
11. Install the rider seat.
AirCheducnec
ir filter element 1. A
AND MINOR REPAIR
6
AThthteadadYasarie
EAU00637
djusting the valve clearance e valve clearance changes with use,
sulting in improper air-fuel mixtured/or engine noise. To prevent thism occurring, the valve clearance
ust be adjusted by a Yamaha dealer the intervals specified in the periodicaintenance and lubrication chart.
E_5MT.book Page 22 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-22
EAU00628
djusting the carburetors e carburetors are important parts of
e engine and emission control sys-m, which require very sophisticatedjustment. Therefore, all carburetorjustments should be left to amaha dealer, who has the neces-ry professional knowledge and expe-nce.
EAU00635
Adjusting the throttle cable free play The throttle cable free play shouldmeasure 6–8 mm (0.2–0.3 in) at thethrottle grip. Periodically check thethrottle cable free play and, if neces-sary, have a Yamaha dealer adjust it.
AThreanfromatm
a. Throttle cable free play
PE
6
TirTo ity,cycreg
TirThechebef
_
�
�
_
EW000083
WARNINGper loading of your motorcyclemportant for several characteris- of your motorcycle, such asdling, braking, performance and
ety. Do not carry loosely packeds that can shift. Securely packr heaviest items close to theter of the motorcycle, and dis-ute the weight evenly from sideide. Properly adjust the suspen-
n for your load, and check thedition and pressure of your tires.
VER OVERLOAD YOUR MOTOR-CLE. Make sure that the totalight of the cargo, rider, passen-, and accessories (cowling, sad-bags, etc. if approved for thisdel) does not exceed the maxi-m load of the motorcycle. Opera- of an overloaded motorcycleld cause tire damage, an acci-t, or even injury.
E_5MT.book Page 23 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-23
EAU03581
es maximize the performance, durabil- and safe operation of your motor-le, note the following pointsarding the specified tires.
e air pressure tire air pressure should becked and, if necessary, adjustedore each ride.
EW000082
WARNINGThe tire air pressure must bechecked and adjusted on coldtires (i.e., when the temperatureof the tires equals the ambienttemperature). The tire air pressure must beadjusted in accordance with theriding speed and with the totalweight of rider, passenger, car-go, and accessories approvedfor this model.
CE-22E
CE-16E
_
Prois iticshansafitemyoucentribto ssioconNECYwegerdlemomutioncouden_
Tire air pressure(measured on cold tires)
Load* Front Rear
Up to 90 kg (198 lb)250 kPa 2.50 kgf/cm2
36 psi
250 kPa2.50 kgf/cm2
36 psi
90 kg (198 lb)–maximum
250 kPa2.50 kgf/cm2
36 psi
290 kPa2.90 kgf/cm2
42 psi
High-speed riding250 kPa2.50 kgf/cm2
36 psi
250 kPa2.50 kgf/cm2
36 psi
Maximum load*YZF-R6: 189 kg (417 lb)
YZF-R6C: 188 kg (415 lb)
* Total weight of rider, passenger, cargo and accessories
AND MINOR REPAIR
6
TiAlthcrif intahaCE
re informationis motorcycle is equipped with casteels and tubeless tires with valves.
1.2.a.
M(
Tire air valveTire air valve coreTire air valve cap with seal
E_5MT.book Page 24 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-24
re inspectionways check the tires before operatinge motorcycle. If a tire tread showsosswise lines (minimum tread depth),the tire has a nail or glass fragments it, or if the side wall is cracked, con-ct a Yamaha dealer immediately andve the tire replaced.
-09E
EW000094
WARNING_
� It is dangerous to ride with aworn-out tire. When a tire treadbegins to show crosswise lines,have a Yamaha dealer replacethe tire immediately.
� The replacement of all wheel-and brake-related parts, includ-ing the tires, should be left to aYamaha dealer, who has thenecessary professional knowl-edge and experience.
_
TiThwh
Tire sidewallTire wear indicatorTire tread depth
inimum tire tread depth front and rear)
1.0 mm (0.04 in)
1.2.3.
PE
6
_
�
�
�
�
_
EAU00684
WARNINGis motorcycle is fitted with super-h-speed tires. Note the followingints in order to make the most ef-ient use of these tires.
Use only the specified replace-ment tires. Other tires may runthe danger of bursting at superhigh speeds.Brand-new tires can have a rela-tively poor grip on certain roadsurfaces until they have been“broken in”. Therefore, it is ad-visable before doing any high-speed riding to ride conserva-tively for approximately 100 km(60 mi) after installing a newtire.The tires must be warmed upbefore a high-speed run.Always adjust the tire air pres-sure according to the operatingconditions.
E_5MT.book Page 25 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-25
EW000080
WARNINGThe front and rear tires shouldbe of the same make and de-sign, otherwise the handlingcharacteristics of the motor-cycle cannot be guaranteed.After extensive tests, only thetires listed below have been ap-proved for this model byYamaha Motor Co., Ltd.Always make sure that the valvecaps are securely installed toprevent air pressure leakage.Use only the tire valves andvalve cores listed below toavoid tire deflation during ahigh-speed ride.
CE-17E
CE-14E
@
Thhigpofic
�
�
�
�
@
FRONT
Manufacturer Size Model
Michelin120/60 ZR17 (55W)
Pilot SPORT B120/60 ZR17 M/C (55W)
Dunlop120/60 ZR17 (55W)
D207FJ120/60 ZR17 M/C (55W)
REAR
Manufacturer Size Model
Michelin180/55 ZR17 (73W)
Pilot SPORT B180/55 ZR17 M/C (73W)
Dunlop180/55 ZR17 (73W)
D207N180/55 ZR17 M/C (73W)
FRONT & REAR
Tire air valve TR412
Valve core #9000A (original)
AND MINOR REPAIR
6
CToitycyre
the use of items which have noten approved by Yamaha.
E_5MT.book Page 26 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-26
EAU03773
ast wheels maximize the performance, durabil-, and safe operation of your motor-cle, note the following pointsgarding the specified wheels.� The wheel rims should be checked
for cracks, bends or warpage be-fore each ride. If any damage isfound, have a Yamaha dealer re-place the wheel. Do not attempteven the smallest repair to thewheel. A deformed or crackedwheel must be replaced.
� The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.
� Ride at moderate speeds afterchanging a tire since the tire sur-face must first be “broken in” for itto develop its optimal characteris-tics.
EAU00691
Accessories and replacement parts
EW000098
WARNING@
This motorcycle is not designed topull a trailer or to be attached to asidecar. The accessories or replace-ment parts you choose for yourmotorcycle should be designed spe-cifically for this model, and theymust be securely mounted to main-tain the inherent stability of the orig-inal design. Genuine Yamaha Partsand Accessories are designed andtested to be compatible with yourmotorcycle. Please consider Genu-ine Yamaha Parts and Accessoriesbefore making a purchase. Use ofnon-Yamaha-approved accessoriesor replacement parts may causeloss of handling stability and ridingsafety. Since Yamaha cannot con-trol the quality of accessories orparts manufactured by other com-panies, Yamaha cannot be held lia-ble for any consequences caused
bybe@
PE
6
AdplaThesurPeplalowTo turnverclubol
Remove cowling A. (See page 6-7for cowling removal and installa-tion procedures.)Loosen the locknut at the crank-case.To increase the clutch lever freeplay, turn the adjusting nut in di-rection a. To decrease the clutchlever free play, turn the adjustingnut in direction b.Tighten the locknut.Install the cowling.
1. Cc. C
ocknutlutch lever free play adjusting nut rank case)
E_5MT.book Page 27 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-27
EAU01356
justing the clutch lever free y clutch lever free play should mea-
e 10–15 mm (0.4–0.6 in) as shown.riodically check the clutch lever freey and, if necessary, adjust it as fol-s.increase the clutch lever free play, the adjusting bolt at the clutch le-
in direction a. To decrease thetch lever free play, turn the adjustingt in direction b.
NOTE:@
If the specified clutch lever free playcannot be obtained as describedabove, proceed as follows. @
1. Fully turn the adjusting bolt at theclutch lever in direction a to loos-en the clutch cable.
2.
3.
4.
5.6.
lutch lever free play adjusting boltlutch lever free play
1. L2. C
(c
AND MINOR REPAIR
6
ApThpo(0fochneju
EAU00713
djusting the rear brake light itch
e rear brake light switch, which is ac-ated by the brake pedal, is properlyjusted when the brake light comes just before braking takes effect. Ifcessary, adjust the brake light switch follows.rn the adjusting nut while holding the
ar brake light switch in place. Toake the brake light come on earlier,rn the adjusting nut in direction a. Toake the brake light come on later,rn the adjusting nut in direction b.
a. Rear brake light switchRear brake light switch adjusting nut
E_5MT.book Page 28 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-28
EAU01357
djusting the brake pedal osition e top of the brake pedal should besitioned approximately 7–11 mm.28–0.43 in) below the bottom of theotrest bracket as shown. Periodicallyeck the brake pedal position and, ifcessary, have a Yamaha dealer ad-
st it.
EW000109
WARNING_
A soft or spongy feeling in the brakepedal can indicate the presence ofair in the hydraulic system. If thereis air in the hydraulic system, have aYamaha dealer bleed the system be-fore operating the motorcycle. Air inthe hydraulic system will diminishthe braking performance, whichmay result in loss of control and anaccident. _
AswThtivadonneasTuremtumtu
Distance between brake pedal and footrest bracket
1.2.
PE
6
ChbrThecheifielub
EAU04396
r brake padsh rear brake pad is provided with ar indicator groove, which allows to check the brake pad wear with- having to disassemble the brake.ck the brake pad wear as follows.Remove the brake caliper bolt,and then tilt the caliper forward toinspect the wear indicator groove.If a brake pad has worn to thepoint that the wear indicatorgroove has almost disappeared,have a Yamaha dealer replace thebrake pads as a set.
oltear brake caliper
ar
E_5MT.book Page 29 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-29
EAU00721
ecking the front and rear ake pads front and rear brake pads must becked for wear at the intervals spec-
d in the periodic maintenance andrication chart.
EAU00725
Front brake padsEach front brake pad is provided with awear indicator groove, which allowsyou to check the brake pad wear with-out having to disassemble the brake.To check the brake pad wear, checkthe wear indicator groove. If a brakepad has worn to the point that the wearindicator groove has almost disap-peared, have a Yamaha dealer replacethe brake pads as a set.
ReaEacweayououtChe
1.
1. Brake pad wear indicator groove
Front
1. B2. R
Re
AND MINOR REPAIR
6
2 bserve these precautions:� When checking the fluid level,
make sure that the top of the brakefluid reservoir is level.
� Use only the recommended quali-ty brake fluid, otherwise the rubberseals may deteriorate, causingleakage and poor braking perfor-mance.
� Refill with the same type of brakefluid. Mixing fluids may result in aharmful chemical reaction andlead to poor braking performance.
1.
R
Minimum level mark
Recommended brake fluid: DOT 4
ear
E_5MT.book Page 30 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-30
. Install the brake caliper bolt, andthen tighten it to the specifiedtorque.
EAU03294
Checking the brake fluid level Insufficient brake fluid may allow air toenter the brake system, possibly caus-ing it to become ineffective.Before riding, check that the brake fluidis above the minimum level mark andreplenish if necessary. A low brake flu-id level may indicate worn brake padsand/or brake system leakage. If thebrake level is low, be sure to check thebrake pads for wear and the brake sys-tem for leakage.
O
Brake pad wear indicator groove
Tightening torque:Brake caliper bolt:
27 Nm (2.7 m·kgf, 20 ft·lb)
ear
1. Minimum level mark
Front
1.
R
PE
6
�
�
�
EAU00744
ive chain slack drive chain slack should becked before each ride and adjusted
ecessary.
check the drive chain slack Place the motorcycle on a levelsurface and hold it in an uprightposition.
TE:en checking and adjusting the drivein slack, the motorcycle should beitioned straight up and there shouldno weight on it.
Shift the transmission into the neu-tral position.
E_5MT.book Page 31 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-31
Be careful that water does not en-ter the brake fluid reservoir whenrefilling. Water will significantlylower the boiling point of the fluidand may result in vapor lock.Brake fluid may deteriorate paint-ed surfaces or plastic parts. Al-ways clean up spilled fluidimmediately.As the brake pads wear, it is nor-mal for the brake fluid level togradually go down. However, if thebrake fluid level goes down sud-denly, have a Yamaha dealercheck the cause.
EAU03976
Changing the brake fluid Have a Yamaha dealer change thebrake fluid at the intervals specified inthe NOTE after the periodic mainte-nance and lubrication chart. In addition,have the oil seals of the master cylin-ders and calipers as well as the brakehoses replaced at the intervals listedbelow or whenever they are damagedor leaking.
� Oil seals: Replace every twoyears.
� Brake hoses: Replace every fouryears.
DrThecheif n
To 1.
NO@
Whchaposbe @
2.
AND MINOR REPAIR
6
3
4
. To tighten the drive chain, turn theadjusting bolt on each side of theswingarm in direction a. To loos-en the drive chain, turn the adjust-ing bolt on each side of theswingarm in direction b, and thenpush the rear wheel forward.
a. Bolt (× 3)Rear brake caliperBrake caliper bracket
E_5MT.book Page 32 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-32
. Move the rear wheel by pushingthe motorcycle to locate the tight-est portion of the drive chain, andthen measure the drive chainslack as shown.
. If the drive chain slack is incorrect,adjust it as follows.
EAU04372
To adjust the drive chain slack 1. Loosen the axle nut, the brake cal-
iper bracket bolt and the locknuton each side of the swingarm.
2
Drive chain slack
Drive chain slack:40–50 mm (1.6–2.0 in)
1. Axle nut2. Drive chain slack adjusting bolt3. Locknut4. Alignment marks
1.2.3.
PE
6
NO_
Ussidbottion_
CA_
Imploaparto prethespe_
3.
ECA00052
UTION: not use engine oil or any otherricants for the drive chain, asy may contain substances thatld damage the O-rings.
T
E_5MT.book Page 33 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-33
TE:ing the alignment marks on eache of the swingarm, make sure thath chain pullers are in the same posi- for proper wheel alignment.
EC000096
UTION:roper drive chain slack will over-
d the engine as well as other vitalts of the motorcycle and can leadchain slippage or breakage. Tovent this from occurring, keep drive chain slack within thecified limits.
Tighten the locknuts, and thentighten the axle nut and the brakecaliper bracket bolt to the specifiedtorques.
EAU03006
Lubricating the drive chain The drive chain must be cleaned andlubricated at the intervals specified inthe periodic maintenance and lubrica-tion chart, otherwise it will quickly wearout, especially when riding in dusty orwet areas. Service the drive chain asfollows.
EC000097
CAUTION:@
The drive chain must be lubricatedafter washing the motorcycle orriding in the rain. @
1. Clean the drive chain with kero-sene and a small soft brush.
ECA00053
CAUTION:@
To prevent damaging the O-rings,do not clean the drive chain withsteam cleaners, high-pressurewashers or inappropriate solvents. @
2. Wipe the drive chain dry.3. Thoroughly lubricate the drive
chain with a special O-ring chainlubricant.
CA@
Dolubthecou@
ightening torque:Axle nut:
150 Nm (15.0 m·kgf, 108 ft·lb)Brake caliper bracket bolt:
40 Nm (4.0 m·kgf, 29 ft·lb)
AND MINOR REPAIR
6
CcaThthchbledorYa
@
Dblanmblun@
EAU03164
ecking and lubricating the ake and clutch levers e operation of the brake and clutchers should be checked before eache, and the lever pivots should be lu-cated if necessary.
Recommended lubricant:Lithium-soap-based grease (all-purpose grease)
E_5MT.book Page 34 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-34
EAU03297
hecking and lubricating the bles e operation of all control cables and
e condition of the cables should beecked before each ride, and the ca-
es and cable ends should be lubricat- if necessary. If a cable is damaged does not move smoothly, have amaha dealer check or replace it.
EW000111
WARNINGamage to the outer housing of ca-es may result in internal rustingd cause interference with cableovement. Replace damaged ca-es as soon as possible to preventsafe conditions.
EAU04034
Checking and lubricating the throttle grip and cable The operation of the throttle grip shouldbe checked before each ride. In addi-tion, the cable should be lubricated orreplaced at the intervals specified inthe periodic maintenance chart.
ChbrThlevridbri
Recommended lubricant:Yamaha Chain and Cable Lube
orengine oil SAE 10W-30 (API SE)
PE
6
ChbrThepedridebric
R
ecommended lubricant:Lithium-soap-based grease (all-purpose grease)
E_5MT.book Page 35 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-35
EAU03370
ecking and lubricating the ake and shift pedals operation of the brake and shiftals should be checked before each, and the pedal pivots should be lu-ated if necessary.
EAU03165
Checking and lubricating the sidestand The operation of the sidestand shouldbe checked before each ride, and thesidestand pivot and metal-to-metalcontact surfaces should be lubricated ifnecessary.
EW000113
WARNING@
If the sidestand does not move upand down smoothly, have a Yamahadealer check or repair it. @
ecommended lubricant:Lithium-soap-based grease (all-purpose grease)
R
AND MINOR REPAIR
6
LsuThsispan
check the operation. Place the motorcycle on a level
surface and hold it in an uprightposition.
. While applying the front brake,push down hard on the handle-bars several times to check if thefront fork compresses and re-bounds smoothly.
EC000098
AUTION:any damage is found or the frontrk does not operate smoothly,ve a Yamaha dealer check or re-ir it.
E_5MT.book Page 36 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-36
EAU04282
ubricating the rear spension e pivoting points of the rear suspen-
on must be lubricated at the intervalsecified in the periodic maintenanced lubrication chart.
EAU02939
Checking the front fork The condition and operation of the frontfork must be checked as follows at theintervals specified in the periodic main-tenance and lubrication chart.
To check the conditionEW000115
WARNING@
Securely support the motorcycle sothat there is no danger of it fallingover. @
Check the inner tubes for scratches,damage and excessive oil leakage.
To1
2
C@
If fohapa@
Recommended lubricant:Lithium-soap-based grease
PE
6
ChWocauof tlowriodcha
1.
@
Sethaove@
EAU01144
ecking the wheel bearings front and rear wheel bearings must
checked at the intervals specified in periodic maintenance and lubrica- chart. If there is play in the wheel or if the wheel does not turn
oothly, have a Yamaha dealerck the wheel bearings.
E_5MT.book Page 37 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-37
EAU00794
ecking the steering rn or loose steering bearings mayse danger. Therefore, the operationhe steering must be checked as fol-s at the intervals specified in the pe-ic maintenance and lubricationrt.Place a stand under the engine toraise the front wheel off theground.
EW000115
WARNINGcurely support the motorcycle sot there is no danger of it fallingr.
2. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steer-ing.
ChThebe thetionhubsmche
AND MINOR REPAIR
6
BThsenonoad
ToHtehabaif tio
� KEEP THIS AND ALL BATTER-IES OUT OF THE REACH OFCHILDREN.
E_5MT.book Page 38 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-38
EAU01291
attery is motorcycle is equipped with aaled-type (MF) battery, which doest require any maintenance. There is need to check the electrolyte or tod distilled water.
charge the batteryave a Yamaha dealer charge the bat-ry as soon as possible if it seems tove discharged. Keep in mind that thettery tends to discharge more quicklythe motorcycle is equipped with op-nal electrical accessories.
EW000116
WARNING@
� Electrolyte is poisonous anddangerous since it contains sul-furic acid, which causes severeburns. Avoid any contact withskin, eyes or clothing and al-ways shield your eyes whenworking near batteries. In caseof contact, administer the fol-lowing FIRST AID.• EXTERNAL: Flush with plenty
of water.• INTERNAL: Drink large quan-
tities of water or milk and im-mediately call a physician.
• EYES: Flush with water for15 minutes and seek promptmedical attention.
� Batteries produce explosive hy-drogen gas. Therefore, keepsparks, flames, cigarettes, etc.,away from the battery and pro-vide sufficient ventilation whencharging it in an enclosedspace.
@
PE
6
To1.
2.
3.
4.
EAU04375
placing the fuses main fuse and the fuse box, whichtains the fuses for the individual cir-s, are located under the rider seat.e page 3-13 for rider seat removal installation procedures.)
fuse is blown, replace it as follows.Turn the key to “OFF” and turn offthe electrical circuit in question.Remove the blown fuse, and theninstall a new fuse of the specifiedamperage.
eadlight fuseadiator fan fusenition fuseignaling system fuseackup fuse (odometer and clock)pare fuse (× 3)
E_5MT.book Page 39 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-39
store the batteryIf the motorcycle will not be usedfor more than one month, removethe battery, fully charge it, andthen place it in a cool, dry place.If the battery will be stored formore than two months, check it atleast once a month and fullycharge it if necessary.Fully charge the battery before in-stallation.After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.
EC000102
CAUTION:@
� Always keep the batterycharged. Storing a dischargedbattery can cause permanentbattery damage.
� To charge a sealed-type (MF)battery, a special (constant-voltage) battery charger is re-quired. Using a conventionalbattery charger will damage thebattery. If you do not have ac-cess to a sealed-type (MF) bat-tery charger, have a Yamahadealer charge your battery.
@
ReTheconcuit(SeandIf a
1.
2.
1. H2. R3. Ig4. S5. B6. S
ND MINOR REPAIR
6
C_
Dagavthfir_
1.2.
E_5MT.book Page 40 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE A
6-40
EC000103
AUTION:o not use a fuse of a higher amper-e rating than recommended tooid causing extensive damage toe electrical system and possibly ae.
3. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.
4. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.
Main fuseSpare main fuse
Specified fuses:Main fuse: 30 AHeadlight fuse: 20 ASignaling system fuse: 15 ARadiator fan fuse: 7.5 AIgnition fuse: 15 ABackup fuse (odometer and clock): 7.5 A
PE
6
ReThiquabul
1.
2.
EC000104
TION: care not to damage the follow-arts:eadlight bulbo not touch the glass part of
he headlight bulb to keep it freerom oil, otherwise the transpar-ncy of the glass, the luminosi-y of the bulb, and the bulb lifeill be adversely affected. Thor-ughly clean off any dirt and fin-erprints on the headlight bulbsing a cloth moistened with al-ohol or thinner.eadlight lensDo not affix any type of tintedfilm or stickers to the head-light lens.Do not use a headlight bulb ofa wattage higher than speci-fied.
nstall the headlight bulb cover,nd then connect the coupler.
nstall the panel.ave a Yamaha dealer adjust theeadlight beam if necessary.
1. H2. B
E_5MT.book Page 41 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-41
EAU04226
placing a headlight bulb s motorcycle is equipped with twortz bulb headlights. If a headlight
b burns out, replace it as follows.Remove panel A. (See page 6-9for panel removal and installationprocedures.)Disconnect the headlight coupler,and then remove the bulb cover.
3. Unhook the headlight bulb holder,and then remove the defectivebulb.
EW000119
WARNING_
Headlight bulbs get very hot. There-fore, keep flammable products awayfrom a lit headlight bulb, and do nottouch the bulb until it has cooleddown. _
4. Place a new headlight bulb intoposition, and then secure it withthe bulb holder.
CAU_
Takeing p
� HDtfetwoguc
� H•
•
_
5. Ia
6. I7. H
h
eadlight couplerulb cover
1. Headlight bulb holder
ND MINOR REPAIR
6
TThLEIf ha
E_5MT.book Page 42 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE A
6-42
EAU03730
ail/brake light is motorcycle is equipped with anD type of tail/brake light.
the tail/brake light does not come on,ve a Yamaha dealer check it.
EAU03497
Replacing a turn signal light bulb
1. Remove the turn signal light lensby removing the screw.
2. Remove the defective bulb bypushing it in and turning it counter-clockwise.
3. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.
4. Install the lens by installing thescrew.
ECA00065
CAUTION:@
Do not overtighten the screw, other-wise the lens may break.
1. Screw
PE
6
SuSincenwhwhnanstacycbefstroder
To1.
2.
EAU01824
nt wheel
remove the front wheel EW000122
WARNINGIt is advisable to have a Yamahadealer service the wheel.Securely support the motor-cycle so that there is no dangerof it falling over.
Loosen the front wheel axle pinchbolt, then the brake caliper bolts.Loosen the wheel axle with a 19-mm hexagon wrench.
heel axleront wheel axle pinch bolt
E_5MT.book Page 43 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-43
EAU01579
pporting the motorcycle ce this model is not equipped with aterstand, follow these precautions
en removing the front and reareel or performing other mainte-ce requiring the motorcycle to
nd upright. Check that the motor-le is in a stable and level positionore starting any maintenance. Ang wooden box can be placed un- the engine for added stability.
service the front wheelStabilize the rear of the motorcycleby using a motorcycle stand or, ifan additional motorcycle stand isnot available, by placing a jack un-der the frame in front of the rearwheel.Raise the front wheel off theground by using a motorcyclestand.
To service the rear wheelRaise the rear wheel off the ground byusing a motorcycle stand or, if a motor-cycle stand is not available, by placinga jack either under each side of theframe in front of the rear wheel or undereach side of the swingarm.
Fro
To
@
�
�
@
1.
2.
1. W2. F
AND MINOR REPAIR
6
3
4
5
C@
Dbrotfo@
6
. Push down hard on the handlebarseveral times to check for properfork operation.
1.2.3.4.
Tightening torques:Wheel axle:
72 Nm (7.2 m·kgf, 52 ft·lb)Front wheel axle pinch bolt:
20 Nm (2.0 m·kgf, 14 ft·lb)Brake caliper bolt:
40 Nm (4.0 m·kgf, 29 ft·lb)
E_5MT.book Page 44 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-44
. Lift the front wheel off the groundaccording to the procedure onpage 6-43.
. Remove the brake hose holdersby removing the bolts.
. Remove the brake calipers and re-flectors by removing the bolts.
ECA00046
AUTION:o not apply the brake after theake calipers have been removed,herwise the brake pads will berced shut.
. Pull the wheel axle out, and thenremove the wheel.
EAU04267
To install the front wheel 1. Lift the wheel up between the fork
legs.2. Insert the wheel axle.3. Lower the front wheel so that it is
on the ground. 4. Install the brake calipers and re-
flectors by installing the bolts.
NOTE:_
Make sure that there is enough spacebetween the brake pads before install-ing the brake calipers onto the brakediscs. _
5. Install the brake hose holders byinstalling the bolts.
6. Tighten the wheel axle, the frontwheel axle pinch bolt and thebrake caliper bolts to the specifiedtorques.
7Brake hose holderBolt (× 3)Brake caliperReflector
PE
6
ReTo
_
�
�
_
1.
Push the wheel forward, and thenremove the drive chain from therear sprocket.
E:drive chain does not need to besembled in order to remove andll the rear wheel.
Pull the wheel axle out, and thenremove the wheel.
ECA00119
TION:ot apply the brake after thel has been removed togetherthe brake disc, otherwise the
e caliper pistons will be forced
1. A2. D3. L
E_5MT.book Page 45 Tuesday, August 28, 2001 2:05 PM
RIODIC MAINTENANCE AND MINOR REPAIR
6-45
EAU04373
ar wheel remove the rear wheel
EW000122
WARNINGIt is advisable to have a Yamahadealer service the wheel.Securely support the motor-cycle so that there is no dangerof it falling over.
Loosen the axle nut, the brake cal-iper bolts and the brake caliperbracket bolt.
2. Lift the rear wheel off the groundaccording to the procedure onpage 6-43.
3. Remove the axle nut, and then re-move the brake caliper by remov-ing the bolts.
4. Loosen the locknut on each side ofthe swingarm.
5. Turn the drive chain slack adjust-ing bolts fully in direction a.
6.
NOT_
The disasinsta_
7.
CAU_
Do nwheewith brakout. _
xle nutrive chain slack adjusting boltocknut
1. Bolt (× 3)2. Rear brake caliper3. Brake caliper bracket
AND MINOR REPAIR
6
To1
N_
Mbein_
2
3
4
5
EAU03087
oubleshooting though Yamaha motorcycles receivethorough inspection before shipmentm the factory, trouble may occur dur- operation. Any problem in the fuel,mpression, or ignition systems, forample, can cause poor starting ands of power.e following troubleshooting charts
present quick and easy proceduresr checking these vital systems your-lf. However, should your motorcyclequire any repair, take it to a Yamahaaler, whose skilled technicians have
e necessary tools, experience, andow-how to service the motorcycleoperly.e only genuine Yamaha replace-
ent parts. Imitation parts may looke Yamaha parts, but they are oftenerior, have a shorter service life andn lead to expensive repair bills.
E_5MT.book Page 46 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-46
EAU04374
install the rear wheel . Install the wheel by inserting the
wheel axle from the left hand side.
OTE:ake sure that there is enough spacetween the brake pads before install-
g the wheel.
. Install the drive chain onto the rearsprocket, and then adjust the drivechain slack. (See page 6-33 fordrive chain slack adjustment pro-cedures.)
. Install the axle nut, and then lowerthe rear wheel so that it is on theground.
. Install the brake caliper by install-ing the bolts.
. Tighten the axle nut, the brake cal-iper bracket bolt and the brake cal-iper bolts to the specified torques.
TrAla froingcoexlosThrefoseredethknprUsmlikinfca
Tightening torques:Axle nut:
150 Nm (15.0 m·kgf, 108 ft·lb)Brake caliper bracket bolt:
40 Nm (4.0 m·kgf, 29 ft·lb)Brake caliper bolt:
27 Nm (2.7 m·kgf, 20 ft·lb)
PERIODIC M
6
EAU02990
TroubleshootingStarting problems o
EW000125
WARNING@
Keep away open flam stem. @
1. Fuel
not start. ression.
The engine does not start.Have a Yamaha dealercheck the vehicle.
engine does not start.ck the battery.
n the throttle halfway and operateelectric starter.
E_5MT.book Page 47 Tuesday, August 28, 2001 2:05 PM
Check the fuel levthe fuel tank.
Operate the electr
2. Compres
Remove the sparkand check the ele
3. Ignition
Operate the electr
4. Battery
AINTENANCE AND MINOR REPAIR
6-47
charts r poor engine performance
es and do not smoke while checking or working on the fuel sy
el inThere is enough fuel.
There is no fuel.
Check the compression.
Supply fuel. The engine doesCheck the comp
ic starter.
sionThere is compression.
There is no compression.
Check the ignition.
Have a Yamaha dealercheck the vehicle.
plugsctrodes.
Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
ic starter.
The engine turns over quickly.
The engine turns over slowly.
Dry
Wet
TheChe
Opethe
The battery is good.
Check the battery lead connections,and charge the battery if necessary.
AND MINOR REPAIR
6
EnEW000070
@
lding hot fluid and steam may bet until the engine has cooled.el, over the radiator cap, and thenressure to escape. When the hiss-wise, and then remove the cap.
@
N@
If hanged to the recommended coolantas@
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See NOTE.)
. If the engine overheats again, have a check and repair the cooling system.
e isge.
e is akage.
E_5MT.book Page 48 Tuesday, August 28, 2001 2:05 PM
PERIODIC MAINTENANCE
6-48
gine overheating
WARNING� Do not remove the radiator cap when the engine and radiator are hot. Sca
blown out under pressure, which could cause serious injury. Be sure to wai� After removing the radiator cap retaining bolt, place a thick rag, like a tow
slowly rotate the cap counterclockwise to the detent to allow any residual ping sound has stopped, press down on the cap while turning it counterclock
OTE:coolant is not available, tap water can be temporarily used instead, provided that it is c soon as possible.
Wait until the engine has cooled.
Check the coolant level in the reservoir and radiator.
The coolant level is OK.
The coolant level is low.Check the cooling systemfor leakage.
Start the engineYamaha dealer
Therleaka
Therno le
MOTORCYCLE CARE AND STORAGE
7
Care .................................................................................................. 7-1Storage .............................................................................................. 7-4
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
7
EAU03428*
aningECA00010
UTION:
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
7-MO
CaWhreve
Avoid using strong acidic wheelcleaners, especially on spokedwheels. If such products areused on hard-to-remove dirt, donot leave the cleaner on the af-fected area any longer than in-structed. Also, thoroughly rinsethe area off with water, immedi-ately dry it, and then apply acorrosion protection spray.Improper cleaning can damagewindshields, cowlings, panelsand other plastic parts. Useonly a soft, clean cloth orsponge with mild detergent andwater to clean plastic.
noloble.eveusenotifrommodoethe moand
7-1
TORCYCLE CARE AND STORAGE
re ile the open design of a motorcycleals the attractiveness of the tech-gy, it also makes it more vulnera- Rust and corrosion can developn if high-quality components ared. A rusty exhaust pipe may go un-ced on a car, however, it detracts the overall appearance of a
torcycle. Frequent and proper cares not only comply with the terms ofwarranty, but it will also keep your
torcycle looking good, extend its life optimize its performance.
Before cleaning1. Cover the muffler outlet with a
plastic bag after the engine hascooled down.
2. Make sure that all caps and coversas well as all electrical couplersand connectors, including thespark plug caps, are tightly in-stalled.
3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-ucts onto seals, gaskets, sprock-ets, the drive chain and wheelaxles. Always rinse the dirt anddegreaser off with water.
Cle
CA@
�
�
ARE AND STORAGE
7
ter normal usemove dirt with warm water, a mildtergent, and a soft, clean sponge,d then rinse thoroughly with cleanter. Use a toothbrush or bottlebrush
r hard-to-reach areas. Stubborn dirtd insects will come off more easily if
e area is covered with a wet cloth forfew minutes before cleaning. Use theecial sponge, which is included in thestic bag containing the owner’s
anual, to clean the muffler and to re-ove any discoloration from it.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
MOTORCYCLE C
7-2
� Do not use any harsh chemicalproducts on plastic parts. Besure to avoid using cloths orsponges which have been incontact with strong or abrasivecleaning products, solvent orthinner, fuel (gasoline), rust re-movers or inhibitors, brake flu-id, antifreeze or electrolyte.
� Do not use high-pressure wash-ers or steam-jet cleaners since they cause water seepage and deterioration in the following ar-eas: seals (of wheel and swing-arm bearings, fork and brakes), electric components (couplers, connectors, instruments, switches and lights), breather hoses and vents.
� For motorcycles equipped witha windshield: Do not use strongcleaners or hard sponges asthey will cause dulling orscratching. Some cleaningcompounds for plastic mayleave scratches on the wind-shield. Test the product on asmall hidden part of the wind-shield to make sure that it doesnot leave any marks. If the wind-shield is scratched, use a quali-ty plastic polishing compoundafter washing.
@
AfRedeanwafoantha spplamm
M
7
Afton Sindurcomfollrainroa
NO@
Sarem@
1.
CA@
Docresal@
2.
EWA00001
WARNINGMake sure that there is no oil orwax on the brakes or tires. Ifnecessary, clean the brakediscs and brake linings with aregular brake disc cleaner or ac-etone, and wash the tires withwarm water and a mild deter-gent.Before operating the motor-cycle test its braking perfor-mance and cornering behavior.
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
OTORCYCLE CARE AND STORAGE
7-3
er riding in the rain, near the sea orsalt-sprayed roadsce sea salt or salt sprayed on roadsing winter are extremely corrosive inbination with water, carry out the
owing steps after each ride in the, near the sea or on salt-sprayedds.
TE:lt sprayed on roads in the winter mayain well into spring.
Clean the motorcycle with coldwater and a mild detergent, afterthe engine has cooled down.
ECA00012
UTION: not use warm water since it in-ases the corrosive action of thet.
Apply a corrosion protection sprayon all metal, including chrome-and nickel-plated, surfaces to pre-vent corrosion.
After cleaning1. Dry the motorcycle with a chamois
or an absorbing cloth.2. Immediately dry the drive chain
and lubricate it to prevent it fromrusting.
3. Use a chrome polish to shinechrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steel exhaust systems can be re-moved through polishing.)
4. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.
5. Use spray oil as a universal clean-er to remove any remaining dirt.
6. Touch up minor paint damagecaused by stones, etc.
7. Wax all painted surfaces.8. Let the motorcycle dry completely
before storing or covering it.
@
�
�
@
ARE AND STORAGE
7
C@
@
N@
Cw@
ng-termfore storing your motorcycle for sev-
al months:. Follow all the instructions in the
“Care” section of this chapter.. For motorcycles equipped with a
fuel cock that has an “OFF” posi-tion: Turn the fuel cock lever to“OFF”.
. Drain the carburetor float chamberby loosening the drain bolt; this willprevent fuel deposits from buildingup. Pour the drained fuel into thefuel tank.
. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
MOTORCYCLE C
7-4
ECA00013
AUTION:� Apply spray oil and wax spar-
ingly and make sure to wipe offany excess.
� Never apply oil or wax to anyrubber and plastic parts, buttreat them with a suitable careproduct.
� Avoid using abrasive polishingcompounds as they will wearaway the paint.
OTE:onsult a Yamaha dealer for advice onhat products to use.
Storage
Short-termAlways store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover.
ECA00014
CAUTION:@
� Storing the motorcycle in apoorly ventilated room or cover-ing it with a tarp, while it is stillwet, will allow water and humid-ity to seep in and cause rust.
� To prevent corrosion, avoiddamp cellars, stables (becauseof the presence of ammonia)and areas where strong chemi-cals are stored.
@
LoBeer
1
2
3
4
M
7
5.
a
b
c
d
e
@
Tospaspathe@
Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30 °F) or more than30 °C (90 °F)]. For more informa-tion on storing the battery, seepage 6-38.
TE:ke any necessary repairs beforering the motorcycle.
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
OTORCYCLE CARE AND STORAGE
7-5
Perform the following steps to pro-tect the cylinder, piston rings, etc.from corrosion.
. Remove the spark plug caps andspark plugs.
. Pour a teaspoonful of engine oilinto each spark plug bore.
. Install the spark plug caps onto thespark plugs, and then place thespark plugs on the cylinder headso that the electrodes are ground-ed. (This will limit sparking duringthe next step.)
. Turn the engine over several timeswith the starter. (This will coat thecylinder walls with oil.)
. Remove the spark plug caps fromthe spark plugs, and then installthe spark plugs and the spark plugcaps.
EWA00003
WARNING prevent damage or injury fromrking, make sure to ground therk plug electrodes while turning engine over.
6. Lubricate all control cables andthe pivoting points of all levers andpedals as well as of the sidestand/centerstand.
7. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.
8. Cover the muffler outlet with aplastic bag to prevent moisturefrom entering it.
9.
NO@
Masto@
SPECIFICATIONS
8
Specifications .................................................................................... 8-1
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
8
EAU01038
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
8-SP
SpCS-01
M
oil API Service SE, SF, SG or higher
ridge 2.5 L (2.2 Imp qt, 2.6 US qt)
e 2.7 L (2.4 Imp qt, 2.9 US qt)
gine) 3.5 L (3.1 Imp qt, 3.7 US qt)
0 10 30 50 70 90 110 130 ˚F
YAMALUBE 4 (20W-40)or SAE 20W-40
-20 -10 0 10 20 30 40 50 ˚C
YAMALUBE 4 (10W-30)or SAE 10W-30
tor oils that do not contain anti-frictionger car motor oils (often labeledVING II”) contain anti-friction additivestch and/or starter clutch slippage, result-
ponent life and poor engine performance.
D
Bf
E
8-1
ECIFICATIONS
ecifications E
odel YZF-R6/YZF-R6C
imensions
Overall length 2,025 mm (79.7 in)
Overall width 690 mm (27.2 in)
Overall height 1,105 mm (43.5 in)
Seat height 820 mm (32.3 in)
Wheelbase
YZF-R6 1,380 mm (54.3 in)
YZF-R6C 1,385 mm (54.4 in)
Ground clearance 135 mm (5.3 in)
Minimum turning radius 3,400 mm (133.9 in)
asic weight (with oil and full uel tank)
YZF-R6 186 kg (410 lb)
YZF-R6C 187 kg (412 lb)
ngine
Engine type Liquid-cooled 4-stroke, DOHC
Cylinder arrangement Forward-inclined parallel 4-cylinder
Displacement 600 cm3
Bore × Stroke 65.5 × 44.5 mm (2.58 × 1.75 in)
Compression ratio 12.4:1
Starting system Electric starter
Lubrication system Wet sump
Engine oil
Type
Recommended engine classification
Quantity
Without oil filter cartreplacement
With oil filter cartridgreplacement
Total amount (dry en
CAUTION:
Be sure to use momodifiers. Passen“ENERGY CONSERwhich will cause cluing in reduced com
SPECIFICATIONS
8
ratio
3.000
2.875
Constant-mesh 6-speed
Left foot
1st 2.846
2nd 1.947
3rd 1.556
4th 1.333
5th 1.190
6th 1.083
Diamond
24°
81 mm (3.19 in)
Tubeless tire
120/60 ZR17 (55W)
120/60 ZR17 M/C (55W)
er/Michelin / Pilot SPORT B
Dunlop / D207FJ
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
8-2
Coolling system capacity (total amount) 2.15 L (1.89 Imp qt, 2.27 US qt)
Air filter Wet element
Fuel
Type UNLEADED GASOLINE ONLY
Fuel tank capacity 17 L (3.7 Imp gal, 4.5 US gal)
Fuel reserve amount 3.5 L (0.8 Imp gal, 0.9 US gal)
Carburetor
Manufacturer KEIHIN
Model × quantity CVRD37 × 4
Spark plug
Manufacturer/Type
YZF-R6 NGK / CR10EK
YZF-R6C NGK / CR9EK
Gap 0.6-0.7 mm (0.02-0.03 in)
Clutch type Wet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 1.955
Secondary reduction system Chain drive
Number of drive chain sprocket teeth (front/rear)
YZF-R6 16/48
YZF-R6C 16/46
Secondary reduction
YZF-R6
YZF-R6C
Transmission type
Operation
Gear ratio
Chassis
Frame type
Caster angle
Trail
Tires
Front
Type
Size
Manufacturmodel
SP
8
Cast wheel
17 × MT 3.50
17 M/C × MT 3.50
Cast wheel
17 × MT 5.50
17 M/C × MT 5.50
Dual disc brake
Right hand
DOT 4
Single disc brake
Right foot
DOT 4
Telescopic fork
Swingarm (link suspension)
Coil spring / oil damper
Coil spring / gas-oil damper
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
ECIFICATIONS
8-3
Rear
Type Tubeless tire
Size 180/55 ZR17 (73W)
Size 180/55 ZR17 M/C (73W)
Manufacturer/model Michelin / Pilot SPORT B
Dunlop / D207N
Maximum load*
YZF-R6 189 kg (417 lb)
YZF-R6C 188 kg (415 lb)
Tire air pressure (mesure on cold tires)
Up to 90 kg (198 lb)*
Front 250 kPa, (2.50 kgf/cm2, 36 psi)
Rear 250 kPa, (2.50 kgf/cm2, 36 psi)
90 kg (198 lb)–maximum*
Front 250 kPa, (2.50 kgf/cm2, 36 psi)
Rear 290 kPa, (2.90 kgf/cm2, 42 psi)
High-speed riding
Front 250 kPa, (2.50 kgf/cm2, 36 psi)
Rear 250 kPa, (2.50 kgf/cm2, 36 psi)
* Total weight of rider, passenger, cargo and accessories
Wheels
Front
Type
Size
Rear
Type
Size
Brakes
Front
Type
Operation
Fluid
Rear
Type
Operation
Fluid
Suspension
Front
Rear
Spring/shock absorber
Front
Rear
SPECIFICATIONS
8
30 A
20 A
15 A
7.5 A
15 A
and 7.5 A
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
8-4
Wheel travel
Front 130 mm (5.12 in)
Rear 120 mm (4.72 in)
Electrical system
Ignition system DC-C.D.I.
Charging system
Model A.C. magneto
Standard output 14 V, 320 W@ 5,000 r/min
Battery
Model GT9B-4
Voltage, capacity 12 V, 8 Ah
Headlight type Quartz bulb (halogen)
Bulb voltage, wattage × quantity
Headlight 12 V, 60/55 W × 2
Tail/brake light 13.5 V, 0.6/6.1 W × 2 (LED)
Front turn signal / position light 12 V, 27/8 W × 2
Rear turn signal light 12 V, 27 W × 2
Licence plate light 12 V, 5 W × 1
Meter lighting 12 V, 1.4 W × 2
Neutral indicator light LED
High beam indicator light LED
Turn signal indicator light LED
Fuel level warning light LED
Oil level/coolant temperature warning light LED
Fuses
Main fuse
Headlight fuse
Signaling system fuse
Radiator fan fuse
Ignition fuse
Backup fuse (odometer clock)
CONSUMER INFORMATION
9
Identification numbers ....................................................................... 9-1Key identification number .................................................................. 9-1Vehicle identification number ............................................................. 9-1Model label ........................................................................................ 9-2Reporting safety defects ................................................................... 9-3Motorcycle noise regulation .............................................................. 9-4Maintenance record .......................................................................... 9-5Street and enduro motorcycle limited warranty ................................. 9-7Yamaha extended service .................................................................. 9-9
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
9
EAU01039
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
9-CO
IdeRec
EAU01043
hicle identification number vehicle identification number is
mped into the steering head pipe.ord this number in the space pro-d.
TE: vehicle identification number isd to identify your motorcycle andy be used to register your motor-le with the licensing authority inr area.
ehicle identification number
vehel lavideorddeacle
1.CA-02
2.
CA-02
3.CA-01
9-1
NSUMER INFORMATIONEAU02944
ntification numbers ord the key identification number,icle identification number and mod-bel information in the spaces pro-d below for assistance when
ering spare parts from a Yamahaler or for reference in case the vehi-is stolen.
KEY IDENTIFICATION NUMBER:E
VEHICLE IDENTIFICATION NUMBER:
E
MODEL LABEL INFORMATION:E
EAU01041
Key identification number The key identification number isstamped into the key tag. Record thisnumber in the space provided and useit for reference when ordering a newkey.
VeThestaRecvide
NO@
Theusemacycyou@
1. Key identification number 1. V
MER INFORMATION
9
MThun3-prthfosp
1.
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
CONSU
9-2
EAU03171
odel label e model label is affixed to the frameder the passenger seat. (See page14 for seat removal and installationocedures.) Record the information onis label in the space provided. This in-rmation will be needed when orderingare parts from a Yamaha dealer.
Model label
CO
9
EAU01051
ReIf y injury or death, you should immedi-ate otifying Yamaha Motor Corporation,U.S that a safety defect exists in a groupof v me involved in individual problemsbet
To 3 (or 366-0123 in Washington, D.C.are . You can also obtain other informa-tion
E_5MT.book Page 3 Tuesday, August 28, 2001 2:05 PM
NSUMER INFORMATION
9-3
porting safety defects ou believe that your vehicle has a defect which could cause a crash or could cause ly inform the National Highway Traffic Safety Administration (NHTSA) in addition to n.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds ehicles, it may order a recall and remedy campaign. However, NHTSA cannot becoween you, your dealer, or Yamaha Motor Corporation, U.S.A.
contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-939a) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590 about motor vehicle safety from the Hotline.
MER INFORMATION
9
EAU01053
MTAFe ering inoperative by any person otherth design incorporated into any new ve-hi r or while it is in use or (2) the use ofth erative by any person.
“A S LISTED BELOW”.
Th tc.CL-
E_5MT.book Page 4 Tuesday, August 28, 2001 2:05 PM
CONSU
9-4
otorcycle noise regulation MPERING WITH NOISE CONTROL SYSTEM PROHIBITED:deral law prohibits the following acts or the causing thereof: (1) The removal or rend
an for purposes of maintenance, repair, or replacement of any device or element of cle for the purpose of noise control prior to its sale or delivery to the ultimate purchasee vehicle after such device or element of design has been removed or rendered inop
MONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACT
ese acts include tampering with the following systems; i.e., modification, removal, e01E
Exhaust systemMufflerExhaust pipeSilencer
Intake systemAir cleaner caseAir cleaner elementIntake duct
CO
9
EAU01874
MaCo cle will be required to document thatma t below is printed only as a reminderthaCL-04
leress
Remarks
E_5MT.book Page 5 Tuesday, August 28, 2001 2:05 PM
NSUMER INFORMATION
9-5
intenance record pies of work orders and/or receipts for parts purchased and installed on your motorcyintenance has been completed in accordance with the emissions warranty. The chart maintenance work is required. It is not acceptable proof of maintenance work.E
Maintenanceinterval
Date ofservice
MileageServicing dea
name and addr
600 mi(1,000 km) or
1 month
4,000 mi( 7,000 km) or
6 months
8,000 mi(13,000 km) or
12 months
12,000 mi(19,000 km) or
18 months
16,000 mi(25,000 km) or
24 months
20,000 mi(31,000 km) or
30 months
24,000 mi(37,000 km) or
36 months
MER INFORMATION
9
alerress
Remarks
E_5MT.book Page 6 Tuesday, August 28, 2001 2:05 PM
CONSU
9-6
28,000 mi(43,000 km) or
42 months
32,000 mi(49,000 km) or
48 months
36,000 mi(55,000 km) or
54 months
40,000 mi(61,000 km) or
60 months
Maintenanceinterval
Date ofservice
MileageServicing de
name and add
CO
9
EAU02918
. ARRANTY
E_5MT.book Page 7 Tuesday, August 28, 2001 2:05 PM
NSUMER INFORMATION
9-7
YAMAHA MOTOR CORPORATION, U.S.ASTREET AND ENDURO MOTORCYCLE LIMITED W
MER INFORMATION
9
E_5MT.book Page 8 Tuesday, August 28, 2001 2:05 PM
CONSU
9-8
CO
9
EAU01063
E_5MT.book Page 9 Tuesday, August 28, 2001 2:05 PM
NSUMER INFORMATION
9-9
YAMAHA EXTENDED SERVICE (Y.E.S.)
MER INFORMATION
9
E_5MT.book Page 10 Tuesday, August 28, 2001 2:05 PM
CONSU
9-10
D
ce f in
ttakb
akb
akakakakakakak
bnrbrettoCCws
uggage strap holders ...........................3-21
ain switch/steering lock .........................3-1aintenance and lubrication, periodic ......6-4aintenance, emission control system.....6-3aintenance, periodic ..............................6-1aintenance record .................................9-5odel label ..............................................9-2
eutral indicator light ...............................3-2oise regulation .......................................9-4
il level/coolant temperature warning light ..........................................3-3
arking.....................................................5-5art locations ...........................................2-1re-operation check list............................4-1
ear suspension, lubricating ..................6-36
afety defects, reporting ..........................9-3afety information ....................................1-1eats .....................................................3-13
Passenger seat.................................3-14Rider seat .........................................3-13
elf-diagnosis device ...............................3-7
E_5MT.book Page 1 Tuesday, August 28, 2001 2:05 PM
10-IN
AAcAirAir
BBaBr
luBr
luBrBrBrBrBrBrBr
CCaCaCaCaCluCluCo
Coin
DDim
e pads, checking.............................6-29e pedal............................................3-10e pedal position, adjusting ..............6-28
les, checking and lubricating............6-34ister (for California only)...................6-11uretors, adjusting............................6-22.........................................................7-1
ch lever..............................................3-9ch lever free play, adjusting .............6-27lant ..................................................6-15hanging..........................................6-17hecking ..........................................6-15lings and panel, removing and talling ................................................6-7
mer switch .........................................3-7
Fuel tank cap......................................... 3-11Fuses, replacing .................................... 6-39
HHandlebar switches ................................. 3-7Headlight bulb, replacing ....................... 6-41Helmet holders ...................................... 3-15High beam indicator light ......................... 3-2Horn switch ............................................. 3-8
IIdentification numbers ............................. 9-1Ignition circuit cut-off system.................. 3-22Indicator and warning lights ..................... 3-2
KKey identification number ........................ 9-1
LLabels, location ....................................... 1-7
PPPP
RR
SSSS
S
EX
ssories and replacement parts .......6-26ilter element, checking .....................6-19take duct ........................................6-21
ery ...................................................6-38e and clutch levers, checking and ricating ............................................6-34e and shift pedals, checking and ricating ............................................6-35e fluid, changing .............................6-31e fluid level, checking......................6-30e lever...............................................3-9e light switch (rear), adjusting .........6-28
Drive chain, lubricating .......................... 6-33Drive chain slack ................................... 6-31
Adjusting .......................................... 6-32Checking.......................................... 6-31
EEngine break-in ....................................... 5-5Engine oil and oil filter cartridge ............. 6-11Engine stop switch................................... 3-8
FFront and rear suspension settings........ 3-20Front fork, adjusting............................... 3-16Front fork, checking ............................... 6-36Fuel ....................................................... 3-11Fuel level warning light ............................ 3-2
L
MMMMMMM
NNN
OO
INDEX
Sh
ShShSidSidSpSpSpStaStaStaStaSteStoStoSu
TTaTaThTh
luTirToTroTroTuTuTu
E_5MT.book Page 2 Tuesday, August 28, 2001 2:05 PM
rt switch.............................................. 3-8ering, checking ................................. 6-37rage.................................................... 7-4rage compartment ............................ 3-15pporting the motorcycle ..................... 6-43
chometer ............................................. 3-6il/brake light ....................................... 6-42rottle cable free play, adjusting .......... 6-22rottle grip and cable, checking and bricating............................................ 6-34es ...................................................... 6-23ol kit..................................................... 6-1ubleshooting..................................... 6-46ubleshooting charts .......................... 6-47
rn signal indicator light ......................... 3-2rn signal light bulb, replacing ............. 6-42rn signal switch.................................... 3-8
ifting .................................................... 5-3Decelerating....................................... 5-4Shift points ......................................... 5-4Starting out and accelerating.............. 5-3
ift pedal ............................................... 3-9ock absorber assembly, adjusting ..... 3-18estand .............................................. 3-21estand, checking and lubricating....... 6-35ark plugs, checking ............................. 6-9ecifications .......................................... 8-1eedometer unit .................................... 3-5rter (choke) lever .............................. 3-13rting and warming up a cold engine.... 5-1rting a warm engine............................ 5-2
VValve clearance, adjusting .................... 6-22Vehicle identification number................... 9-1
WWarranty, extended................................. 9-9Warranty limited ...................................... 9-7Wheel bearings, checking ..................... 6-37Wheel (front) ......................................... 6-43
Installing .......................................... 6-44Removing ........................................ 6-43
Wheel (rear) .......................................... 6-45Installing .......................................... 6-46Removing ........................................ 6-45
Wheels.................................................. 6-26
5MT-28199-11LIT-11626-15-32
YZF-R6PYZF-R6PC
OWNER’S MANUAL
PRINTED IN JAPAN2001 . 7 - 4.0 × 1 CR
(E)
PRINTED ON RECYCLED PAPER
YAMAHA MOTOR CO., LTD.