vector tecklok catalog

5/26/2018 Vector TeckLok Catalog

1/34

A four-bolt pipe connector typically weighi

75% less than a comparable standard ANS

or API flange

TechlokClamp Connector

V

ectorInternational

TechlokClampConnector


2/34

A radially-bolted mechanical pipe connectionwhich allows quick make-up and break-out andis ideal where space, weight and joint integrityare critical requirements.

Techlok Clamp Connectors are the most effective and economical pipe connectio

system available today. Typically several Techlok joints can be installed in the time it

takes to assemble a single standard ANSI or API flange.

Conventional ANSI or API flanges with their eight to 24 bolts require accurate

alignment to ensure a seal, whereas Techlok Clamp Connectors have only four bolts,

no alignment problems and require less bolt loads.

As is well known, external bending forces are an inevitable part of any piping

system, resulting in high stresses being placed on pipe joints. Independent strain gaug

and destructive tests have shown the Techlok connector can withstand considerable

bending moments/forces and axial loading under pressure without leaking or the bolt

becoming loose, greatly reducing maintenance costs at the same time as being highly

beneficial to the environment.

High pressure systems are not a problem, with Techlok connectors working in

applications where pressures of 30,000psi and above are found; and when it comes t

offshore applications where topside loading is critical, Techloks low weight is a real

advantage - a factor applicable in any industry where weight and overall installation co

is a consideration.

Corrosive applications

In more corrosive applications where the specifications demand the use of exotic

materials, the sheer size difference between conventional flanges and Techlok Clamp

Connectors (typically 75%) ensures operators and contractors a real competitive

advantage when determining capex/opex budgets.

But its not just size and weight that makes Techlok the natural choice.

Unlike conventional ANSI flanges, Techlok Clamp Connectors are bolted radially t

the pipe, not along its axis. This means that the clamp can be orientated in any positio

around the pipe, and together with their greatly reduced size, this eliminates clearanc

problems and enables critical components like valve hand wheels to be aligned to the

optimum positions before fully tightening the clamp bolts.


2

Saving up to 75% weight/space

Hibernia topside platformAtlantic Canada

Size 4 2500 class ANSI flange and 4 Techlok connector


3/34

Some of the Benefits

As well as high performance, leak-free, competitive price and greater efficiency

Techlok connectors have many other advantages over conventional flanges:

Up to 75% lighter and significantly smaller than a comparable ANSI or API flange

Close piping and hook-up arrangements with typically 25% smaller clamp diameter

Typically 40% shorter connection length

Easier fabrication and installation with no bolt holes to align

On sizes up to and including 36, only 4 bolts to tighten rather than up to 24 on a

conventional flange

The clamp can be rotated round the hub for easy bolt orientation and tightening

Ancillary components such as valves and piping layouts can be installed withoutworrying about bolt hole alignment

Quicker and easier make-up and breakout minimises maintenance downtime

Lower bolt torque: typically 50% less than that for a ring joint flange

Sealing integrity is unaffected by over-tensioning bolts

Short make and break times - several Techlok connectors can usually be assembled

or disassembled in the time it takes for a single ANSI or API flange connection

It is not usually necessary to re-tighten bolts once in service

In most cases only one clamp size is required for each nominal pipe size

Unlike spiral-wound gaskets, reusable sealrings give greater flexibility forhydro-testing and commissioning prior to service

Reduced inventory

Readily available machining details for interface with associated equipment such asvalves, pumps and metering equipment

Available in all materials to suit the piping specification

Fully Assembled

Pressure Energised Seal

Prior to Assembly

Self Energised Seal

The Techlok advantage

The heart of Techloks success is the energised seal. Techlok clamp connectors do not

rely on the conventional flanges gaskets and correctly tensioned bolting to maintain the

integrity of the seal. The four bas ic elements of the Techlok clamp connector are hubs,

sealring, clamps and bolting. When bolting the assembly, the hubs are drawn together by

the twin wedge action of the two clamp segments compressing on the seal ring to make

the first-stage self-energising seal.

The applied bolting loads are transmitted to the clamps through almost 360 contact

with the hubs. And as the bolts are transversely mounted they are almost completelyisolated from the operating loads, resulting in a strong, reliable yet compact connection.

In service the sealring becomes even more effective as internal pressure reinforces the

metal-to-metal seal to the extent that its strength can normally exceed the burst pressure of

the connected pipe.


4/34

Techlok Components

Hubs

A critical feature of Techlok hubs is their conical seat which creates the

interference with the sealring lips to make the seal. Hubs are

manufactured from the same generic material as the piping

system on which they are to be utilised. They are then either

welded to the pipe or machined integrally onto associated

equipment such as valves.

Butt weld hubs are supplied with standard ANSI B16.25

weld profiles. Blind hubs are a lso

available for blanking off a pipe

section or for pressure

vessel closures.

Clamps

The two Techlok clamp segments make

virtually 360 contact round the hubs. The seal is

made when the bolts are tightened, drawing the

two clamp halves together and clamping the hubs

against the sealring. The clamp bolt holes have

spherical seats to accept the spherically faced nuts

to ensure a perfect fit.

Bolting

Techlok clamp connectors come complete witstandard size nuts and bolts in a variety of coating

to suit every type of piping application. Each

connector requires only four bolts (which

encompasses a 100% safety / redundancy factor)

and the nuts are spherically-faced to eliminate

bending stresses in the bolts during assembly.

Sealring

The key to the Techlok system is its

sealring. Techloks sealring has a central rib

section and two seal lips tapered to match the

conical seat profile of the hubs. It is these lips

which make the pressure-energised seal.

Deformation remains essentially elastic throughout, making the

sealring reusable.

The rib provides a positive stop during make-up, preventing the lips

from being crushed by over tightening and also transferring compressive

and bending loads from one hub to the other.

Sealrings are manufactured from high strength steel compatible with the hub

materials. Typically, precipitation-hardening stainless steels such as grades 630 or 660,

or Alloy 718 are specified for corrosion resistant applications, while low alloy steels are

used for carbon steel pipes. Coating the sealring with a lubricant such as PTFE prevents

the surfaces galling during make-up and enhances reusability.

4

Techlok's sealring has many advantages

over conventional gaskets. For example:

Assured joint integrity first time every time

The gasket forces and seal diameter areminimal, meaning that the load capacity of the

components is maximised

The proven reliability of the pressure-energisebore seal makes Techlok connectors compact

and up to 75% lighter than comparably rated

flanges

The lack of a conventional flange gasket gives a

gas-tight metal-to-metal seal

Techlok TechlokTechlok

CompressionTension Bending

As is well known, external bending forces

are an inevitable part of any piping system,

resulting in high stresses being placed on pipe

joints. Independent strain gauge and

destructive tests have shown the Techlok

connector can withstand considerable bending

moments/forces and axial loading under

pressure without leaking or the bolts

becoming loose, greatly reducing maintenancecosts at the same time as being highly

beneficial to the environment.


5/34

Quality Assurance

As one of the earliest members of First Point Assessment Ltd (FPAL) Vectors

quality and delivery performance is consistently monitored by this independent

authority that acts on behalf of the major operators and their contractors in the

North Sea.

As well as meeting the current industry Standard for Interchangeability Techlok

connectors can also be supplied to meet other design codes and regulations

including:

ASME B31.3/ASME VIII Div1 and Div2

API6A/ISO 10423

PD 5500

UK Offshore Regulations

Customers special requirements

Country Codes

NORSOK

PED (Pressure Equipment Directive)

Independent quality audit assessments have been

carried out by the following operators and

contractors on Vectors design and manufacturing

facilities;

ABB Offshore Systems

Saudi Aramco

Amec

NPCC

AECL (Nuclear)

BP

ExxonMobil (The Netherlands & North Sea)

Kvaerner Engineering

Maersk Oil & Gas

ConocoPhillips

Shell Exploration & Production

GE Canada (Nuclear)

Dominion Bridge (Nuclear)

Statoil

J Ray McDermott

Nemo Engineering AS

Type Approval Testing

The Techlok range of connectors has been subjected to

extensive strain gauge and destructive testing under independent

conditions both in-house and at recognised test centres, and,

after combined pressure and external load type testing, carries

Type Approval by Bureau Veritas.

API Fire Testing

It is important to analyse product performance correctly when specifying pipe

connectors. Extensive testing has shown the Techlok range of clamp connectors will

suit most applications.

Successful strain gauge testing under full load conditions, fire testing to API 6FB

parts 1 and 2, independent testing and witnessing resulting in Bureau Veritas Type

Approval, and extensive Finite Element Analysis during the fire test programme, make

Techlok today the most comprehensively tested clamp connector available


6/34

Weld-O-Hubs

Weld-O-Hubs

Techlok Weld-O-Hubs enable pipework branch connections to be made with

single weld, and provide full reinforcement for the pipe run integral with the

Techlok hub.

Weld-O-Hubs are available in all materials to suit piping requirements, in the

standard size range 1" to 6".

D

40

A

A

PIPE RUN OR MANIFOLD

SECTION A-A

PIPING)

E MAX(TO SUIT

A

B

40

C

NominalPipe Size

SizeDesignation

ClampSize

RingSize

HubO/DA

Back FaceO/DB

LipO/DC

LengthO/DD

SealringBore

E

ins. ins. ins. ins. ins. ins. ins. ins. ins.

1/2 1in/4 1 4 50.8 38.2 7.95 75 12.6

1/2 1in/5 1 5 50.8 38.2 7.95 75 15.8

3/4 1in/5 1 5 50.8 38.2 7.95 75 15.8

3/4 1in/7 1 7 50.8 38.2 7.95 75 22.9

1 1in/5 1 5 50.8 38.2 7.95 75 15.8

1 1in/7 1 7 50.8 38.2 7.95 75 22.9

1 1in/11 1 11 50.8 38.2 7.95 75 28.4

11/2 11/2in/11 11/2 11 79.4 60.5 12.70 110 28.4

11/2 11/2in/14 11/2 14 79.4 60.5 11.10 110 40.7

2 2in/11 2 11 92.1 73.2 12.70 125 28.4

2 2in/14 2 14 92.1 73.2 11.10 125 40.7

2 2in/20 2 20 92.1 73.2 11.10 125 52.2

3 3in/20 3 20 127.0 101.7 12.70 150 52.2

3 3in/23 3 23 127.0 101.7 12.70 150 60.1

3 3in/25 3 25 127.0 101.7 12.70 150 67.6

3 3in/27 3 27 127.0 101.7 12.70 150 77.5

4 4in/25 4 25 152.4 127.2 12.70 175 67.6

4 4in/31 4 31 152.4 127.2 12.70 175 82.3

4 4in/34 4 34 152.4 127.2 12.70 175 93.4

4 4in/40 4 40 152.4 127.2 12.70 175 102.9

6 6in/40R* 6 40 235.0 197.1 23.79 220 102.9

6 6in/46R* 6 46 235.0 197.1 23.79 220 120.2

6 6in/52 6 52 235.0 197.1 20.62 220 134.5

6 6in/62 6 62 235.0 197.1 19.05 220 153.5

8 8in/52R* 8 52 292.1 254.2 23.79 250 134.5

8 8in/62 8 62 292.1 254.2 19.05 250 153.5

8 8in/72 8 72 292.1 254.2 19.05 250 183.5

8 8in/76 8 76 292.1 254.2 19.05 250 196.2

8 8in/82 8 82 292.1 254.2 19.05 250 208.9

Pipe connections can be made with just a single weld

Provides full reinforcement with pipe runs integral with the hub

Available in all materials to suit piping requirements

Standard sizes available from 1" to 6"

Also available Weld-O-Flange for the SPO Compact Flange

6


7/34

ClampSize

Clamp IDBolt

CentresClamp OD

OverallLength

ClampWidth

Lug Sepa-ration

ClampClearance

Bolt Dia.Bolt

LengthBolt LugWidth

Bolt PitchAssemblyClearance

Cl

A B C D E F G H I J K L

ins mm ins mm ins mm ins mm ins mm ins mm ins mm ins mm ins mm ins mm ins mm ins mm Lb

Standard Series

1in 1.69 43 3.25 83 2.81 71 4.25 108 1.38 35 2.19 56 2.63 67 0.50 13 3.50 89 2.25 57 1.25 32 1.9 48 4.2

1.5in 2.69 68 5.00 127 4.50 114 6.50 165 2.00 51 3.25 83 4.00 102 0.63 16 5.00 127 3.13 80 1.63 41 3.0 76 9.9

2in 3.20 81 5.75 146 5.50 140 7.50 191 2.00 51 3.52 89 4.50 114 0.75 19 5.25 133 3.38 86 1.81 46 3.6 91 13.

3in 4.38 111 7.50 191 6.88 175 9.25 235 2.38 61 4.60 117 5.25 133 0.75 19 6.50 165 3.38 86 1.81 46 4.6 117 23.

4in 5.38 137 8.50 216 8.25 210 10.50 267 2.38 61 5.40 137 6.00 152 0.88 22 7.50 191 4.00 102 2.06 52 5.4 137 28.

5in 6.88 175 10.25 260 9.88 251 12.38 315 3.13 80 6.13 156 7.25 184 1.00 25 8.25 210 4.50 114 2.31 59 6.9 175 41.

6in 8.38 213 12.63 321 12.00 305 15.25 387 3.75 95 6.88 175 8.75 222 1.13 29 10.63 270 5.25 133 2.44 62 8.0 203 70.

8in 10.63 270 15.25 387 14.50 368 18.50 470 3.75 95 7.88 200 9.88 251 1.25 32 12.00 305 5.75 146 2.88 73 9.4 239 110

Light Duty Series

L14in 16.38 416 22.25 565 21.50 546 26.00 660 5.00 127 10.88 276 14.75 375 1.63 41 17.00 432 7.38 188 3.63 92 13.3 338 275

L16in 18.63 473 24.00 610 23.50 597 27.75 705 5.00 127 13.00 330 16.25 413 1.75 44 19.50 495 7.63 194 3.88 99 14.5 368 308

L18in 20.88 530 25.75 654 26.00 660 29.50 749 5.00 127 14.38 365 17.50 445 1.88 48 21.50 546 8.00 203 4.13 105 15.9 404 352

L20in 23.63 600 28.31 719 29.38 746 32.25 819 5.00 127 17.13 435 19.50 495 2.00 51 24.75 629 8.50 216 4.38 111 17.7 450 418

L24in 28.31 719 34.25 870 34.75 883 38.88 988 6.25 159 18.38 467 22.50 572 2.25 57 27.00 686 9.50 241 5.00 127 21.4 544 661

Heavy Duty Series

H2in 4.13 105 7.25 184 6.88 175 9.00 229 2.88 73 4.88 124 5.63 143 0.88 22 7.50 191 3.75 95 2.00 51 4.6 117 24.

H3in 4.88 124 8.00 203 7.75 197 10.00 254 3.00 76 5.43 138 6.13 156 0.88 22 7.50 191 4.00 102 2.06 52 5.1 130 33.

H4in 6.13 156 9.56 243 9.00 229 11.75 298 3.00 76 5.75 146 7.00 178 1.00 25 8.25 210 4.38 111 2.31 59 5.9 150 39.

H8in 10.13 257 16.00 406 14.75 375 18.63 473 4.50 114 7.50 191 10.75 273 1.38 35 12.00 305 5.88 149 3.13 80 9.8 249 13

H10in 12.25 311 18.25 464 17.63 448 22.50 572 5.50 140 10.50 267 12.75 324 1.63 41 15.63 397 7.25 184 3.63 92 11.4 290 24

H12in 14.63 372 21.00 533 20.38 518 25.00 635 5.75 146 11.25 286 14.25 362 1.75 44 17.00 432 7.50 191 3.75 95 13.0 330 32

H14in 17.13 435 24.75 629 23.00 584 29.25 743 6.13 156 11.25 286 16.25 413 1.88 48 17.25 438 8.25 210 4.25 108 14.6 371 43

H16in 19.69 500 29.25 743 27.19 691 34.25 870 7.63 194 13.50 343 19.13 486 2.25 57 22.00 559 9.63 245 5.00 127 16.9 429 68

H18in 20.69 526 29.25 743 27.69 703 34.25 870 7.63 194 14.00 356 19.63 499 2.25 57 22.00 559 9.63 245 5.00 127 17.3 439 65

H20in 23.69 602 32.00 813 30.38 772 37.63 956 7.50 191 18.00 457 21.50 546 2.25 57 26.00 660 10.00 254 5.00 127 18.8 478 86

H22in 24.69 627 32.00 813 32.25 819 37.63 956 7.50 191 18.00 457 21.50 546 2.25 57 26.00 660 10.00 254 5.00 127 19.9 506 81

H24in 28.19 716 36.00 914 36.13 918 40.50 1029 7.00 178 19.40 493 23.75 603 2.25 57 27.00 686 10.50 267 5.00 127 22.1 561 104

H26in 29.94 761 38.75 984 37.85 961 46.50 1181 8.00 203 19.60 498 27.00 686 2.50 64 28.00 711 10.50 267 5.50 140 23.1 587 115

Techlok Clampsets


8/34

8

Heavy Duty Butt Weld and Blind Hubs

N.P.S (DN)

PipeSched-

ule

TechlokDesigna-tion Hub/ S.Ring

Pipe Hub Hub Hub Lip Blind Hub BW Hub Blin

O.Dia. I.Dia. O.Dia. LengthBackface

DiaThickness Thickness Wt. W

A B C D E F G

ins. mm ins. mm ins. mm ins. mm ins. mm ins. mm ins. mm Lbs. Kg Lbs.

2 (DN

50) Std 40 40S H2in20 2.07 52.5 4.75 120.7 3.25 82.6 3.75 95.3 0.63 15.9 1.88 47.6 6.2 2.8 7

2.38 60.3 XS 80 80S H2in20 1.94 49.3 4.75 120.7 3.25 82.6 3.75 95.3 0.63 15.9 1.88 47.6 6.5 2.9 7

160 H2in16 1.69 42.9 4.75 120.7 3.25 82.6 3.75 95.3 0.63 15.9 1.88 47.6 7.1 3.2 7

XXS H2in14 1.50 38.2 4.75 120.7 3.25 82.6 3.75 95.3 0.63 15.9 1.88 47.6 7.5 3.4 7

3 (DN

75) Std 40 40S H3in27 3.07 77.9 5.50 139.7 3.50 88.9 4.50 114.3 0.63 15.9 2.13 54.0 7.3 3.3 11

3.50 88.9 XS 80 80S H3in27 2.90 73.7 5.50 139.7 3.50 88.9 4.50 114.3 0.63 15.9 2.13 54.0 8 3.6 11

160 H3in25 2.62 66.6 5.50 139.7 3.50 88.9 4.50 114.3 0.63 15.9 2.13 54.0 9.2 4.2 11

XXS H3in23 2.30 58.4 5.50 139.7 3.50 88.9 4.50 114.3 0.63 15.9 2.13 54.0 10.3 4.7 11

4 (DN

100) Std 40 40S H4in40 4.03 102.3 6.75 171.5 4.00 101.6 5.75 146.1 0.63 15.9 2.75 69.8 11.9 5.4 21.9

4.50 114.3 XS 80 80S H4in40 3.83 97.2 6.75 171.5 4.00 101.6 5.75 146.1 0.63 15.9 2.75 69.8 13 5.9 21.9

120 H4in34 3.62 92.1 6.75 171.5 4.00 101.6 5.75 146.1 0.63 15.9 2.75 69.8 14.3 6.5 21.9

160 H4in34 3.44 87.3 6.75 171.5 4.00 101.6 5.75 146.1 0.63 15.9 2.75 69.8 15.5 7 21.9

XXS H4in31 3.15 80.1 6.75 171.5 4.00 101.6 5.75 146.1 0.63 15.9 2.75 69.8 17.2 7.8 21.9

8 (DN

200) Std 40 40S H8in82 7.98 202.7 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 31.6 14.3 73.3

8.63 219.1 XS 80 80S H8in76 7.63 193.7 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 38.3 17.4 73.3

100 H8in76 7.44 189.0 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 40.3 18.3 73.3

120 H8in72 7.19 182.6 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 45.4 20.6 73.3

140 H8in72 7.00 177.8 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 47.2 21.4 73.3

XXS H8in67 6.88 174.6 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 50.1 22.7 73.3

160 H8in67 6.81 173.1 11.50 292.1 5.00 127.0 9.50 241.3 1.00 25.4 3.19 81.0 50.7 23 73.3

10 (DN

250) S td 40 40S H10in102 10.02 254.5 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 49.9 22.6 119.2

10.75 273.1 XS 60 80S H10in97 9.75 247.7 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 57.5 26.1 119.2

80 H10in97 9.56 242.9 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 60.7 27.6 119.2

100 H10in94 9.31 236.6 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 67.6 30.7 119.2

120 H10in92 9.06 230.2 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 71.4 32.4 119.2

XXS140 H10in87 8.75 222.3 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 80.5 36.5 119.2

160 H10in84 8.50 215.9 13.63 346.1 6.00 152.4 11.63 295.3 1.25 31.8 3.50 88.9 86.2 39.1 119.2

12 (DN

300) Std 40s H12in120 12.00 304.8 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 77.1 35 184.5

12.75 323.9 40 H12in120 11.94 303.2 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 78.8 35.8 184.5

XS 80S H12in116 11.75 298.5 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 85.4 38.7 184.5

80 H12in116 11.38 289.0 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 94.4 42.8 184.5

100 H12in112 11.06 281.0 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 104.3 47.3 184.5

XXS 120 H12in106 10.75 273.1 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 112.9 51.2 184.5

140 H12in106 10.50 266.7 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 118.3 53.7 184.5

160 H12in102 10.13 257.2 16.00 406.4 6.63 168.3 14.00 355.6 1.38 34.9 4.00 101.6 129.3 58.7 184.5

14 (DN

350) 40 H14in134 13.12 333.3 18.50 469.9 7.25 184.2 16.50 419.1 1.19 30.1 4.50 114.3 124.7 56.6 290.8

14.00 355.6 XS H14in130 13.00 330.2 18.50 469.9 7.25 184.2 16.50 419.1 1.19 30.1 4.50 114.3 133.2 60.4 290.8

80 H14in124 12.50 317.5 18.50 469.9 7.25 184.2 16.50 419.1 1.25 31.8 4.50 114.3 153.3 69.5 291.8

100 H14in124 12.12 307.9 18.50 469.9 7.25 184.2 16.50 419.1 1.25 31.8 4.50 114.3 163.8 74.3 291.8


9/34

Heavy Duty Butt Weld and Blind Hubs contd

120 H14in120 11.81 300.1 18.50 469.9 7.25 184.2 16.50 419.1 1.25 31.8 4.50 114.3 177.3 80.4 291.8

140 H14in116 11.50 292.1 18.50 469.9 7.25 184.2 16.50 419.1 1.25 31.8 4.50 114.3 187.2 84.9 291.8

160 H14in112 11.19 284.2 18.50 469.9 7.25 184.2 16.50 419.1 1.25 31.8 4.50 114.3 197 89.4 289.8

16 (DN

400) XS 40 H16in152 15.00 381.0 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 194.8 88.4 431.2

16.00 406.4 60 H16in152 14.69 373.1 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 206.3 93.6 431.2

80 H16in144 14.31 363.6 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 229.1 103.9 431.2

100 H16in140 13.94 354.0 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 247.5 112.3 431.2

120 H16in137 13.56 344.5 21.00 533.4 7.88 200.0 19.00 482.6 1.63 41.3 5.00 127.0 260.5 118.2 430.1

140 H16in134 13.12 333.3 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 279.4 126.8 431.2

160 H16in130 12.81 325.4 21.00 533.4 7.88 200.0 19.00 482.6 1.69 42.9 5.00 127.0 293.9 133.3 431.2

18 (DN450)

40 H18in170 16.88 428.7 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 176 79.8 476.1

18.00 457.2 60 H18in170 16.50 419.1 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 191.7 86.9 476.1

80 H18in160 16.13 409.6 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 219.8 99.7 476.1

100 H18in160 15.69 398.5 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 238.1 108 476.1

120 H18in152 15.25 387.4 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 262.8 119.2 476.1

140 H18in152 14.88 377.9 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 276.4 125.4 476.1

160 H18in144 14.44 366.7 22.00 558.8 7.88 200.0 20.00 508.0 1.69 42.9 5.00 127.0 299.2 135.7 476.1

20 (DN

500) 40 H20in192 18.81 477.9 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 262.7 119.2 681.4

20.00 508 60 H20in185 18.38 466.8 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 295.1 133.9 681.4

80 H20in180 17.94 455.6 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 327.6 148.6 681.4

100 H20in180 17.44 442.9 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 351.9 159.6 681.4

120 H20in170 17.00 431.8 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 386.5 175.3 681.4

140 H20in170 16.50 419.1 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 408.7 185.4 681.4

160 H20in160 16.06 408.0 25.00 635.0 8.75 222.3 23.00 584.2 1.63 41.3 5.50 139.7 440.3 199.7 681.4

22 (DN

550) 40 H22in210 20.75 527.1 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 219.8 99.7 732

22.00 558.8 60 H22in210 20.25 514.4 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 247 112 732

80 H22in200 19.75 501.7 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 295.2 133.9 732

100 H22in192 19.25 489.0 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 333.3 151.2 732

120 H22in192 18.75 476.3 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 358.9 162.8 732

140 H22in185 18.25 463.6 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 391.8 177.7 732

160 H22in180 17.75 450.9 26.00 660.4 8.75 222.3 24.00 609.6 1.25 31.8 5.50 139.7 424.8 192.7 732

24 (DN

600) 40 H24in225 22.62 574.7 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 360.3 163.4 1040.2

24.00 609.6 60 H24in220 22.06 560.4 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 409.6 185.8 1040.2

80 H24in220 21.56 547.7 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 441.6 200.3 1040.2

100 H24in210 20.94 531.8 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 496.8 225.4 1040.2

120 H24in210 20.38 517.6 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 527.4 239.2 1040.2

140 H24in200 19.88 504.9 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 573 259.9 1040.2

160 H24in200 19.31 490.6 29.50 749.3 9.00 228.6 27.50 698.5 1.25 31.8 6.00 152.4 600.1 272.2 1040.2

26 (DN

650) Std H26in254 25.25 641.4 31.12 793.8 10.00 254.0 29.25 743.0 1.63 41.3 6.50 165.1 360.8 163.7 1279.8

26.00 660.4 XS H26in254 25.00 635.0 31.12 793.8 10.00 254.0 29.25 743.0 1.63 41.3 6.50 165.1 382.2 173.3 1279.8

N.P.S (DN)

PipeSched-

ule

TechlokDesigna-tion Hub/ S.Ring

Pipe Hub Hub Hub Lip Blind Hub BW Hub Blin



A B C D E F G



10/34

Standard Butt Weld and Blind Hubs

N.P.S (DN)

PipeSched-

ule

TechlokDesig-nationHub /

S.Ring

Pipe Hub Hub Hub Lip Blind Hub BW Hub Bli


DiaThickness Thickness Wt.

A B C D E F G


1/2 (DN 15) Std 40 40S 1in5 0.62 15.8 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

0.84 21.3 XS 80 80S 1in5 0.55 13.9 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

160 1in4 0.47 11.8 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

XXS 1in4 0.25 6.4 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

3/4 (DN 20) Std 40 40S 1in7 0.82 20.9 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.5 0.2 0.8

1.05 26.7 XS 80 80S 1in7 0.74 18.8 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

160 1in5 0.61 15.6 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.7 0.3 0.8

XXS 1in4 0.43 11.0 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.7 0.3 0.8

1 (DN 25) Std 40 40S 1in11 1.05 26.6 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.5 0.2 0.8

1.32 33.4 XS 80 80S 1in11 0.96 24.3 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.5 0.2 0.8

160 1in7 0.82 20.7 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.6 0.3 0.8

XXS 1in5 0.60 15.2 2.00 50.8 1.75 44.5 1.50 38.1 0.31 8.0 1.31 33.4 0.7 0.3 0.8

1.5 (DN 40) Std 40 40S 1.5in14 1.61 40.9 3.13 79.4 2.38 60.3 2.38 60.3 0.44 11.1 1.63 41.3 1.6 0.7 2.4

1.90 48.3 XS 80 80S 1.5in13 1.50 38.1 3.13 79.4 2.38 60.3 2.38 60.3 0.50 12.7 1.63 41.3 1.9 0.8 2.5

160 1.5in13 1.34 34.0 3.13 79.4 2.38 60.3 2.38 60.3 0.50 12.7 1.63 41.3 2 0.9 2.5

XXS 1.5in11 1.10 27.9 3.13 79.4 2.38 60.3 2.38 60.3 0.50 12.7 1.63 41.3 2.4 1.1 2.5

2 (DN 50) Std 40 40S 2in20 2.07 52.5 3.63 92.1 2.75 69.9 2.88 73.0 0.44 11.1 1.75 44.5 2.2 1 3.7

2.38 60.3 XS 80 80S 2in20 1.94 49.3 3.63 92.1 2.75 69.9 2.88 73.0 0.44 11.1 1.75 44.5 2.5 1.1 3.7

160 2in16 1.69 42.9 3.63 92.1 2.75 69.9 2.88 73.0 0.44 11.1 1.75 44.5 3 1.4 3.7

XXS 2in14 1.50 38.2 3.63 92.1 2.75 69.9 2.88 73.0 0.44 11.1 1.75 44.5 3.4 1.5 3.7

3 (DN 75) Std 40 40S 3in27 3.07 77.9 5.00 127.0 3.25 82.6 4.00 101.6 0.50 12.7 1.88 47.6 4.7 2.1 7.7

3.50 88.9 XS 80 80S 3in27 2.90 73.7 5.00 127.0 3.25 82.6 4.00 101.6 0.50 12.7 1.88 47.6 5.2 2.4 7.7

160 3in25 2.62 66.6 5.00 127.0 3.25 82.6 4.00 101.6 0.50 12.7 1.88 47.6 6.3 2.9 7.7

XXS 3in23 2.30 58.4 5.00 127.0 3.25 82.6 4.00 101.6 0.50 12.7 1.88 47.6 7.4 3.3 7.7

4 (DN 100) Std 40 40S 4in40 4.03 102.3 6.00 152.4 3.63 92.1 5.00 127.0 0.50 12.7 2.13 54.0 6.7 3.1 13

4.50 114.3 XS 80 80S 4in40 3.83 97.2 6.00 152.4 3.63 92.1 5.00 127.0 0.50 12.7 2.13 54.0 7.7 3.5 13

120 4in34 3.62 92.1 6.00 152.4 3.63 92.1 5.00 127.0 0.50 12.7 2.13 54.0 8.9 4 13

160 4in34 3.44 87.3 6.00 152.4 3.63 92.1 5.00 127.0 0.50 12.7 2.13 54.0 10 4.5 13

XXS 4in31 3.15 80.1 6.00 152.4 3.63 92.1 5.00 127.0 0.50 12.7 2.13 54.0 11.5 5.2 13

5 (DN 125) Std 40 40S 5in52 5.05 128.2 7.50 190.5 4.38 111.1 6.50 165.1 0.63 15.9 2.75 69.9 13.3 6 27.8

5.56 141.3 XS 80 80S 5in52 4.81 122.3 7.50 190.5 4.38 111.1 6.50 165.1 0.63 15.9 2.75 69.9 14.8 6.7 27.8

160 5in46 4.31 109.6 7.50 190.5 4.38 111.1 6.50 165.1 0.63 15.9 2.75 69.9 19.2 8.7 27.8

XXS 5in40 4.06 103.2 7.50 190.5 4.38 111.1 6.50 165.1 0.63 15.9 2.75 69.9 21.9 9.9 27.8

6 (DN 150) Std 40 40S 6in62 6.07 154.1 9.25 235.0 4.63 117.5 7.75 196.9 0.75 19.1 2.88 73.0 20.4 9.2 42.6

6.63 168.3 XS 80 80S 6in56 5.76 146.3 9.25 235.0 4.63 117.5 7.75 196.9 0.81 20.6 2.88 73.0 24.9 11.3 43

120 6in54 5.50 139.7 9.25 235.0 4.63 117.5 7.75 196.9 0.81 20.6 2.88 73.0 27.7 12.6 43

160 6in52 5.19 131.8 9.25 235.0 4.63 117.5 7.75 196.9 0.81 20.6 2.88 73.0 30.7 13.9 43

XXS 6in52 4.90 124.4 9.25 235.0 4.63 117.5 7.75 196.9 0.81 20.6 2.88 73.0 32.7 14.8 43

8 (DN 200) Std 40 40S 8in82 7.98 202.7 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 33 15 76.2

8.63 219.1 XS 80 80S 8in76 7.63 193.7 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 40.3 18.3 76.2

100 8in76 7.44 189.0 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 42.4 19.2 76.2

120 8in72 7.19 182.6 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 47.8 21.7 76.2

140 8in72 7.00 177.8 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 49.9 22.6 76.2

XXS 8in67 6.88 174.6 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 52.9 24 76.2

160 8in67 6.81 173.1 11.50 292.1 5.38 136.5 10.00 254.0 0.75 19.1 3.19 81.0 53.6 24.3 76.2

10


11/34

Light Duty Butt Weld and Blind Hubs

N.P.S (DN)

PipeSched-

ule

TechlokDesig-nationHub /

S.Ring

Pipe Hub Hub Hub Lip Blind Hub BW Hub Blind



A B C D E F G


14 (DN 350) 40 L14in134 13.12 333.3 17.25 438.2 7.00 177.8 15.75 400.1 0.75 19.1 3.50 88.9 83.4 37.8 201.2

14.00 355.6 XS L14in130 13.00 330.2 17.25 438.2 7.00 177.8 15.75 400.1 0.75 19.1 3.50 88.9 91.7 41.6 201.2

80 L14in124 12.50 317.5 17.25 438.2 7.00 177.8 15.75 400.1 0.81 20.6 3.50 88.9 110.8 50.3 201.9

100 L14in124 12.12 307.9 17.25 438.2 7.00 177.8 15.75 400.1 0.81 20.6 3.50 88.9 120.8 54.8 201.9

120 L14in120 11.81 300.1 17.25 438.2 7.00 177.8 15.75 400.1 0.81 20.6 3.50 88.9 133.8 60.7 201.9

140 L14in116 11.50 292.1 17.25 438.2 7.00 177.8 15.75 400.1 0.81 20.6 3.50 88.9 143.3 65 201.9

160 L14in112 11.19 284.2 17.25 438.2 7.00 177.8 15.75 400.1 0.69 17.4 3.50 88.9 153.4 69.6 200.5

16 (DN 400) XS 40 L16in152 15.00 381.0 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 115.5 52.4 279.4

16.00 406.4 60 L16in152 14.69 373.1 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 126.3 57.3 279.4

80 L16in144 14.31 363.6 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 148.1 67.2 279.4

100 L16in140 13.94 354.0 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 165.6 75.1 279.4

120 L16in137 13.56 344.5 19.50 495.3 7.50 190.5 18.00 457.2 0.69 17.4 3.75 95.3 178.1 80.8 278.7

140 L16in134 13.12 333.3 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 195.7 88.8 279.4

160 L16in130 12.81 325.4 19.50 495.3 7.50 190.5 18.00 457.2 0.75 19.1 3.75 95.3 209.5 95 279.4

18 (DN 450) 40 L18in170 16.88 428.7 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 153.3 69.5 375.1

18.00 457.2 60 L18in170 16.50 419.1 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 169.3 76.8 375.1

80 L18in160 16.13 409.6 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 197.8 89.7 375.1

100 L18in160 15.69 398.5 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 216.5 98.2 375.1

120 L18in152 15.25 387.4 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 241.5 109.6 375.1

140 L18in152 14.88 377.9 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 255.4 115.9 375.1

160 L18in144 14.44 366.7 21.75 552.5 8.00 203.2 20.25 514.4 0.75 19.1 4.00 101.6 278.6 126.4 375.1

20 (DN 500) 40 L20in192 18.81 477.9 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 214 97.1 511.6

20.00 508 60 L20in185 18.38 466.8 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 243.8 110.6 511.6

80 L20in180 17.94 455.6 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 273.6 124.1 511.6

100 L20in180 17.44 442.9 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 294.6 133.8 511.6

120 L20in170 17.00 431.8 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 327 148.3 511.6

140 L20in170 16.50 419.1 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 346.5 157.2 511.6

160 L20in160 16.06 408.0 24.50 622.3 8.00 203.2 23.00 584.2 0.75 19.1 4.25 108.0 375.7 170.4 511.6

24 (DN 600) 40 L24in225 22.62 574.7 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 354.6 160.8 823.8

24.00 609.6 60 L24in220 22.06 560.4 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 403.9 183.2 823.8

80 L24in220 21.56 547.7 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 435.9 197.7 823.8

100 L24in210 20.94 531.8 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 491.1 222.8 823.8

120 L24in210 20.38 517.6 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 521.7 236.6 823.8

140 L24in200 19.88 504.9 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 567.2 257.3 823.8

160 L24in200 19.31 490.6 29.50 749.3 9.00 228.6 27.50 698.5 1.00 25.4 4.75 120.7 594.4 269.6 823.8


12/34

12

Techlok Pressure Temperature Ratings Heavy Duty

NominalSize

TechlokSizeCode

Hub - A350LF2

Hub - A182F316L

Hub - UNS31803

Hub - UNS32760

Hub - AISI4130

Hub - UNSN06625

Hub - A694F65

Hub - AF4

Clamp - LowAlloy Steel







Clamp Alloy S

100F 50C 100F 50C 100F 50C 100F 50C 100F 50C 100F 50C 100F 50C 100F

psi Bar psi Bar psi Bar psi Bar psi Bar psi Bar psi Bar psi

2 H2in13 14207 980 12600 843 19,792 1334 22350 1523 18,267 1,259 25200 973 15628 1077 14312

H2in14 13758 949 12245 819 19,234 1297 21720 1480 17,690 1,220 24490 946 15134 1043 13908

H2in16 12552 865 11277 754 17,714 1194 20003 1363 16,139 1,113 22554 871 13807 952 12809

H2in20 11542 796 10462 700 16,434 1108 18557 1265 14,840 1,023 20924 808 12696 875 11883

3 H3in20 13363 921 11850 792 18,614 1255 21020 1433 17,181 1,185 23700 915 14699 1013 13460

H3in23 12095 834 10821 724 16,998 1146 19194 1308 15,551 1,072 21642 836 13304 917 12291

H3in25 10739 740 9715 650 15,260 1029 17232 1175 13,808 952 19430 750 11813 814 11035

H3in27 7868 542 7216 483 11,335 764 12800 872 10,116 697 14432 557 8655 597 8196

4 H4in25 13359 921 11763 787 18,477 1246 20865 1422 17,176 1,184 23526 908 14695 1013 13361

H4in27 12120 836 10746 719 16,880 1138 19061 1299 15,583 1,074 19649 759 13332 919 12206

H4in31 11467 791 10208 683 16,035 1081 17543 1210 14,743 1,016 17543 677 12614 870 11595

H4in34 9211 635 8245 551 12,951 873 13784 950 11,843 817 13784 532 10132 699 9365

H4in40 6705 462 6115 409 9,605 648 10847 739 8,621 594 11166 431 7375 508 6946

8 H8in52 11765 811 10310 689 13,946 962 13946 962 13,960 962 13946 538 12941 892 11711

H8in56 10845 748 9505 636 11,976 826 11976 826 11,988 827 11976 462 11929 822 10796

H8in62 9087 627 8016 536 10,191 703 10191 703 10,201 703 10191 393 9996 689 9105

H8in64 7428 512 6596 441 8,938 616 8938 616 8,947 617 8938 345 8171 563 7492

H8in67 6117 422 5475 366 8,041 554 8041 554 7,865 542 8041 310 6729 464 6219

H8in72 4708 325 4271 286 6,709 452 7272 501 6,053 417 7272 281 5179 357 4851

10 H10in82 6926 478 6110 409 9,598 647 9660 666 8,905 614 9660 373 7618 525 6940

H10in84 6220 429 5507 368 8,650 583 9125 629 7,997 551 9125 352 6842 472 6255

H10in87 5090 351 4549 304 7,145 482 8069 550 6,545 451 8402 324 5599 386 5167

H10in94 3424 236 3103 208 4,875 329 5505 375 4,402 304 6207 240 3766 260 3525

H10in97 2595 179 2380 159 3,739 252 4222 288 3,336 230 4760 184 2854 197 2703

H10in102 1881 130 1753 117 2,754 186 3110 212 2,418 167 3507 135 2069 143 1992

12 H12in97 7170 494 6283 420 8,555 590 8555 590 8,563 590 8555 330 7887 544 7137

H12in102 6281 433 5523 369 7,963 549 7963 549 7,971 550 7963 307 6909 476 6274

H12in106 5040 347 4466 299 7,014 473 7265 501 6,480 447 7265 281 5544 382 5072

H12in112 3882 268 3471 232 5,452 368 6157 420 4,992 344 6655 257 4271 294 3943

H12in120 2449 169 2230 149 3,503 236 3956 270 3,149 217 4460 172 2694 186 2533

14 H14in106 8691 599 7772 520 9,054 624 9054 624 8,691 599 9054 350 8691 599 8827

H14in112 7837 540 6828 457 7,946 548 7946 548 7,960 549 7946 307 7960 549 7756

H14in116 6759 466 5917 396 7,275 502 7275 502 7,282 502 7275 281 7282 502 6721

H14in120 6290 434 5508 368 7,014 484 7014 484 7,027 484 7014 271 6919 477 6256

H14in124 5126 353 4528 303 6,418 442 6418 442 6,423 443 6418 248 5639 389 5143

H14in130 4115 284 3650 244 5,734 387 6006 414 5,291 365 6006 232 4526 312 4146

H14in134 3232 223 2888 193 4,536 306 5122 349 4,155 286 5581 215 3555 245 3280

16 H16in112 11226 774 9741 651 12,899 889 12899 889 12,912 890 12899 498 12349 851 11064

SEE NOTES ON PAGE 15


13/34

Techlok Pressure Temperature Ratings Heavy Duty con

H16in120 10137 699 8784 587 11,386 785 11386 785 11,397 786 11386 440 11150 769 9977

H16in130 8108 559 7052 472 9,750 672 9750 672 9,760 673 9750 376 8919 615 8010

H16in134 7188 496 6266 419 9,061 625 9061 625 9,070 625 9061 350 7907 545 7117

H16in137 6526 450 5700 381 8,591 590 8591 592 8,391 579 8591 332 7179 495 6474

H16in140 6312 435 5516 369 8,443 576 8443 582 8,115 560 8443 326 6943 479 6265

H16in144 5424 374 4763 319 7,482 504 7886 544 6,974 481 7886 304 5966 411 5410

H16in152 4091 282 3620 242 5,686 383 6421 438 5,260 363 7148 276 4500 310 4112

18 H18in140 6793 468 6560 439 6,793 468 6793 468 6,793 468 6793 262 6793 468 6793

H18in144 6345 437 5833 390 6,345 437 6345 437 6,345 437 6345 245 6345 437 6345

H18in152 5422 374 4761 318 5,751 397 5751 397 5,751 397 5751 222 5751 397 5408

H18in160 4151 286 3666 245 5,237 361 5237 361 5,237 361 5237 202 4566 315 4164

H18in170 2726 188 2437 163 3,828 258 4323 295 3,505 242 4648 179 2999 207 2768

20 H20in152 6722 463 6716 461 6,716 463 6716 463 6,722 463 6716 259 6722 463 6716

H20in160 6121 422 6115 416 6,115 422 6115 422 6,121 422 6115 236 6121 422 6115

H20in170 5432 375 5375 359 5,426 374 5426 374 5,432 375 5426 209 5432 375 5426

H20in180 4645 320 4073 272 4,853 335 4853 335 4,858 335 4853 187 4858 335 4626

H20in185 3753 259 3306 221 4,510 311 4510 311 4,514 311 4510 174 4129 285 3756

H20in192 3011 208 2667 178 4,189 282 4256 293 3,871 267 4256 164 3312 228 3029

22 H22in160 6904 476 6037 404 6,897 476 6897 476 6,904 476 6897 266 6904 476 6857

H22in170 6127 422 5358 358 6,121 422 6121 422 6,127 422 6121 236 6127 422 6086

H22in180 5479 378 4791 320 5,473 377 5473 377 5,479 378 5473 211 5479 378 5442

H22in185 4564 315 3993 267 5,087 351 5087 351 5,092 351 5087 196 5020 346 4535

H22in192 3780 261 3315 222 4,800 331 4800 331 4,805 331 4800 185 4158 287 3765

H22in200 2896 200 2559 171 4,020 271 4453 306 3,723 257 4453 172 3186 220 2907

H22in210 1886 130 1690 113 2,655 179 2998 204 2,425 167 3380 131 2075 143 1920

24 H24in192 5641 389 4815 322 5,835 402 5835 402 5,841 403 5835 225 5841 403 5469

H24in200 5234 361 4467 299 5,415 373 5415 373 5,420 374 5415 209 5420 374 5074

H24in210 4752 328 4056 271 4,916 339 4916 339 4,921 339 4916 190 4921 339 4607

H24in220 3883 268 3398 227 4,487 309 4487 309 4,492 310 4487 173 4271 294 3860

H24in225 3200 221 3275 219 4,224 291 4224 291 4,114 284 4224 163 3520 243 3720

H24in232 2620 181 2309 154 3,627 262 4025 276 3,369 232 4025 155 2882 199 2623

26 H26in225 3985 275 3981 270 3,981 274 3981 274 3,985 275 3981 154 3985 275 3981

H26in232 3799 262 3707 248 3,795 262 3795 262 3,799 262 3795 147 3799 262 3795

H26in240 3476 240 3037 203 3,565 246 3565 246 3,568 246 3565 138 3568 246 3450

H26in244 2998 207 2627 176 3,424 236 3424 236 3,427 236 3424 132 3298 227 2984

H26in254 2136 147 1887 126 2,964 214 3164 218 2,746 189 3164 122 2350 162 2143

H26in264 1389 96 1244 83 1,954 141 2207 150 1,786 123 2488 96 1528 105 1413

H26in270 1059 73 959 64 1,506 109 1701 116 1,362 94 1918 74 1165 80 1089

NominalSize

TechlokSizeCode

Hub - A350LF2

Hub - A182F316L

Hub - UNS31803

Hub - UNS32760

Hub - AISI4130

Hub - UNSN06625

Hub - A694F65

Hub - AF4








Clamp Alloy S





14/34

14

Techlok Pressure Temperature Ratings Standard Dut

NominalSize

TechlokSizeCode

Hub - A350LF2

Hub - A182F316L

Hub - UNS31803

Hub - UNS32760

Hub - AISI4130

Hub - UNSN06625

Hub - A694F65

Hub - AF4








Clamp Alloy S



1 1in4 14481 998 13337 892 20,949 1412 23657 1612 18,619 1,284 26673 1030 15929 1098 15148

1in5 13149 907 12396 829 19,471 1313 21987 1499 16,906 1,166 24791 957 14463 997 14079

1in7 8423 581 9364 626 14,710 992 16611 1132 10,830 747 18439 712 9265 639 10637

1in11 4216 291 5477 366 8,603 580 9715 662 5,421 374 10953 423 4638 320 6221

1.5 1.5in11 12670 874 11634 778 18,275 1232 20637 1407 16,290 1,123 23269 898 13937 961 13215

1.5in13 8518 587 8689 581 13,649 920 15412 1051 10,952 755 17378 671 9370 646 9869

1.5in14 7143 492 7468 499 11,730 791 13246 903 9,184 633 14936 577 7857 542 8482

2 2in13 11926 822 10917 730 17,148 1156 19364 1320 15,333 1,057 21833 843 13118 904 12400

2in14 11059 762 10301 689 16,181 1091 18272 1245 14,218 980 20602 795 12164 839 11701

2in16 8245 568 8193 548 12,870 868 14533 991 10,600 731 16127 623 9069 625 9306

2in20 6090 420 5970 399 9,378 632 10590 722 7,830 540 11940 461 6698 462 6781

3 3in20 12285 847 11013 737 17,300 1166 19535 1332 15,796 1,089 22027 850 13514 932 12509

3in23 10679 736 9699 649 15,235 1027 17204 1173 13,730 947 18421 711 11747 810 11016

3in25 7781 536 7201 482 11,312 763 12773 871 10,004 690 14402 556 8559 590 8179

3in27 4480 309 4378 293 6,877 464 7765 529 5,761 397 8756 338 4928 340 4972

3in31 3115 215 2199 147 3,454 233 3900 266 4,006 276 4398 170 3427 236 2498

4 4in25 12044 830 10719 717 16,837 1135 19013 1296 15,485 1,068 20738 801 13248 913 12175

4in27 9936 685 8906 596 13,989 943 15797 1077 12,775 881 16191 625 10930 754 10115

4in31 8473 584 7664 513 12,039 812 13595 927 10,894 751 14455 558 9320 643 8706

4in34 5354 369 5034 337 7,908 533 8930 609 6,883 475 10069 389 5889 406 5718

4in40 2916 201 2884 193 4,531 305 5116 349 3,749 258 5769 223 3208 221 3276

5 5in31 12779 881 11250 752 17,672 1191 19133 1319 16,430 1,133 19133 739 14057 969 12778

5in34 11476 791 10172 680 15,033 1037 15033 1036 14,755 1,017 15033 580 12623 870 11554

5in40 9661 666 8587 574 12,180 840 12180 840 12,192 841 12180 470 10627 733 9754

5in42 8743 603 7802 522 11,497 793 11497 793 11,241 775 11497 444 9617 663 8862

5in46 5887 406 5380 360 8,451 570 9036 623 7,569 522 9036 349 6476 446 6111

5in52 3082 212 2947 197 4,629 312 5227 356 3,963 273 5894 228 3390 234 3347

6 6in40 12410 856 10878 727 16,071 1108 16071 1108 15,955 1,100 16071 621 13650 941 12356

6in42 11940 823 10489 701 15,170 1046 15170 1046 15,185 1,047 15170 586 13134 906 11914

6in46 10213 704 8999 602 11,923 822 11923 822 11,935 823 11923 460 11235 775 10221

6in52 7463 515 6654 445 9,620 663 9620 663 9,595 662 9620 371 8209 566 7558

6in56 5486 378 4986 333 7,831 528 8261 570 7,053 486 8261 319 6034 416 5663

6in62 3609 249 3362 225 5,281 356 5964 407 4,640 320 6724 260 3970 274 3819

8 8in62 9595 662 8736 584 9,586 661 9586 661 9,595 662 9586 370 9595 662 9586

8in67 6981 481 6189 414 7,563 521 7563 521 7,570 522 7563 292 7570 522 7030

8in72 5561 383 4996 334 6,840 472 6840 472 6,847 472 6840 264 6117 422 5674

8in76 3899 269 3553 238 5,582 376 6026 415 5,012 346 6026 233 4288 296 4036

8in82 2560 176 2386 160 3,747 253 4231 288 3,291 227 4771 184 2816 194 2710



15/34

Techlok Pressure Temperature Ratings Light Duty

NominalSize

TechlokSizeCode

Hub - A350LF2

Hub - A182F316L

Hub - UNS31803

Hub - UNS32760

Hub - AISI4130

Hub - UNSN06625

Hub - A694F65

Hub - AF44








Clamp -Alloy S



14 L14in112 5618 387 4815 322 5816 401 5816 401 5,822 401 5816 225 5822 401 5470

L14in116 5144 355 4409 295 5325 367 5325 367 5,330 367 5325 206 5330 367 5008

L14in120 4682 323 4154 278 5133 354 5133 354 5,138 354 5133 198 5138 354 4718

L14in124 3562 246 3188 213 4697 324 4697 324 4,580 316 4697 181 3918 270 3621

L14in130 2728 188 2466 165 4053 279 4374 298 3,507 242 4396 170 3001 207 2801

L14in134 1977 136 1814 121 2981 206 3217 219 2,542 175 3627 140 2174 150 2060

16 L16in130 4428 305 3796 254 4934 340 4934 340 4,939 341 4934 191 4871 336 4311

L16in134 4115 284 3527 236 4586 316 4586 316 4,591 317 4586 177 4526 312 4006

L16in137 3902 269 3344 224 4348 300 4348 300 4,352 300 4348 168 4292 296 3799

L16in140 3834 264 3287 220 4273 295 4273 295 4,277 295 4273 165 4218 291 3733

L16in144 3337 230 2976 199 3991 275 3991 275 3,995 275 3991 154 3670 253 3380

L16in152 2263 156 2048 137 3366 232 3617 247 2,910 201 3617 140 2489 172 2326

18 L18in144 4085 282 3558 238 4081 281 4081 281 4,085 282 4081 158 4085 282 4041

L18in152 3703 255 3225 216 3699 255 3699 255 3,703 255 3699 143 3703 255 3663

L18in160 3371 232 2936 196 3368 232 3368 232 3,371 232 3368 130 3371 232 3335

L18in170 2486 171 2229 149 2989 206 2989 206 2,992 206 2989 115 2734 189 2532

20 L20in160 3777 260 3238 217 4544 313 4544 313 4,549 314 4544 175 4155 286 3678

L20in170 3352 231 2873 192 4033 278 4033 278 4,037 278 4033 156 3687 254 3263

L20in180 2998 207 2570 172 3607 249 3607 249 3,611 249 3607 139 3298 227 2919

L20in185 2786 192 2388 160 3351 231 3351 231 3,354 231 3351 129 3064 211 2712

L20in192 2590 179 2253 151 3163 218 3163 218 3,166 218 3163 122 2849 196 2559

24 L24in200 3700 255 3357 225 3696 255 3696 255 3,700 255 3696 143 3700 255 3696

L24in210 3359 232 3048 204 3356 231 3356 231 3,359 232 3356 130 3359 232 3356

L24in220 3066 211 2783 186 3063 211 3063 211 3,066 211 3063 118 3066 211 3063

L24in225 2887 199 2619 175 2884 199 2884 199 2,887 199 2884 111 2887 199 2884

NOTES

1. Pressure ratings are intended as a selection guide and assume the following criteria:

a. Bore of hub is based upon the sealring bore

b. Corrosion allowance is 0.063 for carbon/low alloy steels, zero for stainless steels.

c. Hydrotest pressure = 1.5 x pressure rating.

2. Pressure ratings assume AISI 4140 clamps (100 / 75 Ksi, 690/517 MPa) or equivalent.

3. Pressure ratings are calculated on the basis of ASME VIII Div 2 methods and analysis.

4. Pressure ratings to API criteria/materials can be undertaken on request.

5. Combined pressure / external loads / temperature analysis can be undertaken on re

6. Using the full rated pressure of 316 SS components may result in minor distortions

Hydrotest. If in doubt, contact Vector International for further details.

7. 4130 Hub material assumes 90 Ksi tensile (620 MPa) and 60 Ksi yield (414 MPa).


16/34

At the heart of the Techlok connector, there's well proven

successful sealing technology - the metal-to-metal sealring

The sealring creates a leak-free connection, unlike flanges

which leak causing environmental pollution (hydrocarbon

emissions), and bring about delays in commissioning and

production, which in turn has severe cost implications.

The Vector sealring does not leak. It offers weight savings

avoids unscheduled downtime and reduces operational

costs.

The technology behind the sealring is not limited to Vectorproducts. It can be applied to standard flanges as well as

special connections for which Vector can design dedicated

sealing solutions.

Vector Internationals sealrings have been proven over many years of reliable use

in all conditions and in thousands of applications across a wide range of industries.

Each Vector sealring incorporates three essential principles for a high strength, high

integrity joint:

Minimum possible seal diameter to reduce pressure separation loads

Isolated from piping loads

Pressure energised for enhanced seal integrity

Vector sealrings are completely confined within the connection and cannot be

damaged by bending loads or by overtightening the bolts. All sealrings are available

in a wide range of standard sizes and materials, with special materials to suit special

applications available on request.

Sealring

The Complete Solution

technology

16


17/34

Standard Sealrings

The standard sealring has many advantages over conventional gaskets, such as:

Assured joint integrity first time every time

Minimal gasket forces and seal diameter, enabling the load capacity of thecomponents to be maximised

Reliable and proven pressure-energised bore seal concept, making the TechlokClamp Connector up to 75% lighter than comparably-rated flanges

Gas-tight metal-to-metal seal

Reusable

The sealring consists of a central rib section and two seal lips which are tapered to

match the conical seat profile of the hubs. It is these lips which provide the pressure-

energised seal with deformation remaining essentially elastic throughout, and making

the sealring reusable.

The rib acts as a positive stop during make-up, prevents the lips from being

crushed by overtightening, and transfers compressive and bending loads from one

hub to the other.

Coating the sealring with a lubricant such as PTFE prevents the surfaces galling

during make-up and enhances reusability.The sealring is manufactured from high strength steel compatible with the hub

materials. Typically precipitation-hardening stainless steels, such as grades 630 or 660,

or Alloy 718, are specified for corrosion resistant applications, while low alloy steels

are used for carbon steel pipelines.


18/34

Sealringtechnology

18

Blind Sealrings

Blind sealrings are an effective way of blanking-off pipe runs, particularly duringconstruction work-over

Designed as an auxiliary pressure isolation device and should only be used inconjunction with other isolation equipment, e.g. valves

Blinds are marked with a max working pressure. Check for the suitability for youapplication with Vector International

Smaller sizes can usually take full line pressure

Available also with Dur-O-Seal option

Can be provided with indicator flags

Blind sealrings are not recommended for permanent installation or for cyclicloading

Strainer Sealrings

Special Techlok Sealrings, designed and manufactured to the clients ownspecification

During start-up phases, this can be used to protect high value equipment such avalves, pumps and compressors

Can be manufactured in any traditional material associated with the Techloksealring


19/34

Dur-O-Seal

Dur-O-Seal is an alternative sealing mechanism to the standard metal-to-metalTechlok sealring. It is used to maximum advantage where seats are badly corroded

or damaged, or in sandy conditions on service and vessel closures/pig launchers

Design ideal where repeated make-breaks are required

Dur-O-Seal is fully interchangeable with all clamp connectors

It utilises standard, easily replaceable '0' rings

Eliminates the need for costly down time for weld repair or on-site machining ofdamaged hubs

It has a zero extrusion gap which allows for high pressure capacity, and ensures noloss of performance. Note: Dur-O-Seal is not intended for permanent installations

where 'O' ring seals are not to be used due to operating conditions

Orifice Sealrings

Used in conjunction with Techlok Orifice connectors

Can be supplied as one piece or two piece assemblies (such as replacementorifice)

Can be supplied for flow measurement or as a restriction orifice

Sizing calculations can be supplied

Available for all sizes of Techlok sealrings

Transition Sealrings

Designed to accommodate specification breaks of similar nominalpipe sizes i.e. 6in 46 matching to 6in 52 would utilise a transition

seal size 46/52


20/34

20

Techlok Sealrings

SealringSize

Outside Diameter Inside Diameter Rib Thickness Overall Thickness Sealring Weig

A B C D

ins mm ins mm ins mm ins mm Lbs

4 1.00 25 0.50 12.7 0.13 3.2 0.38 9.5 0.03 0

5 1.09 28 0.63 15.9 0.13 3.2 0.38 9.5 0.03 0

7 1.38 35 0.91 23.0 0.13 3.2 0.38 9.5 0.04 0

11 1.75 44 1.13 28.6 0.13 3.2 0.38 9.5 0.06 0

13 2.38 60 1.50 38.1 0.13 3.2 0.38 9.5 0.11 0

14 2.63 67 1.61 40.9 0.25 6.4 0.56 14.3 0.28 0

16 2.75 70 1.87 47.4 0.25 6.4 0.63 15.9 0.28 0

20 3.25 83 2.06 52.4 0.25 6.4 0.75 19.1 0.45 0

23 3.50 89 2.38 60.3 0.25 6.4 0.75 19.1 0.48 0

25 4.00 102 2.67 67.9 0.25 6.4 0.75 19.1 0.62 0

27 4.25 108 3.06 77.8 0.25 6.4 0.75 19.1 0.62 0

31 4.50 114 3.25 82.5 0.25 6.4 0.75 19.1 0.69 0

34 5.00 127 3.69 93.7 0.25 6.4 0.75 19.1 0.80 0

40 5.50 140 4.06 103 0.25 6.4 1.00 25.4 1.13 0

42 6.38 162 4.19 106 0.25 6.4 1.00 25.4 1.68 0

46 6.25 159 4.75 121 0.25 6.4 1.00 25.4 1.34 0

52 6.63 168 5.31 135 0.25 6.4 1.00 25.4 1.33 0

54 6.81 173 5.50 140 0.25 6.4 1.00 25.4 1.57 0

56 7.50 191 5.75 146 0.25 6.4 1.00 25.4 1.82 0

62 7.88 200 6.07 154 0.38 9.5 1.38 34.9 3.13 1

64 8.63 219 6.50 165 0.38 9.5 1.38 34.9 3.80 1

67 8.75 222 6.88 175 0.38 9.5 1.38 34.9 3.61 1

72 9.50 241 7.25 184 0.38 9.5 1.38 34.9 4.40 2

76 10.00 254 7.75 197 0.38 9.5 1.38 34.9 4.67 2

82 10.13 257 8.25 210 0.38 9.5 1.38 34.9 4.26 1

84 11.13 283 8.50 216 0.38 9.5 1.38 34.9 5.79 2

87 11.38 289 8.88 225 0.38 9.5 1.38 34.9 5.77 2

91 11.50 292 9.13 232 0.38 9.5 1.38 34.9 5.66 2

92 11.63 295 9.25 235 0.38 9.5 1.38 34.9 5.78 2

94 11.75 298 9.50 241 0.38 9.5 1.38 34.9 5.61 2

97 12.00 305 9.88 251 0.38 9.5 1.38 34.9 5.55 2

102 12.25 311 10.25 260 0.38 9.5 1.38 34.9 5.48 2

106 12.75 324 10.75 273 0.38 9.5 1.38 34.9 5.72 2

112 14.13 359 11.25 286 0.38 9.5 1.63 41.3 12.30 5

116 14.13 359 11.75 298 0.38 9.5 1.38 34.9 7.21 3

120 13.88 352 12.00 305 0.38 9.5 1.38 34.9 6.04 2

122 14.13 359 12.25 311 0.38 9.5 1.38 34.9 6.16 2

124 14.63 372 12.50 318 0.38 9.5 1.38 34.9 7.10 3

130 15.00 381 13.00 330 0.50 12.7 1.50 38.1 8.47 3

134 15.50 394 13.50 343 0.50 12.7 1.50 38.1 8.78 3

137 16.50 419 13.88 352 0.63 15.9 1.63 41.3 13.70 6

140 16.50 419 14.00 356 0.50 12.7 1.50 38.1 10.98 4

144 17.00 432 14.50 368 0.50 12.7 1.50 38.1 11.35 5

152 17.75 451 15.25 387 0.50 12.7 1.50 38.1 11.89 5

160 18.50 470 16.00 406 0.50 12.7 1.50 38.1 12.44 5


21/34

Techlok Sealrings contd

160 18.50 470 16.00 406 0.50 12.7 1.50 38.1 12.44 5

170 19.44 494 17.00 432 0.50 12.7 1.75 44.4 13.84 6

180 20.50 521 18.00 457 0.50 12.7 1.75 44.4 14.61 6

185 21.25 540 18.62 473 0.50 12.7 1.75 44.4 16.37 7

192 22.00 559 19.25 489 0.50 12.7 1.75 44.4 17.16 7

200 22.75 578 20.00 508 0.50 12.7 1.75 44.4 17.80 8

210 24.00 610 21.00 533 0.50 12.7 2.00 50.8 21.36 9

220 25.00 635 22.00 559 0.50 12.7 2.00 50.8 22.32 1

225 25.75 654 22.62 575 0.50 12.7 2.00 50.8 24.19 1

232 26.38 670 23.25 591 0.50 12.7 2.00 50.8 24.29 1

240 27.50 699 24.00 610 0.50 12.7 2.00 50.8 27.42 1

244 27.75 705 24.50 622 0.50 12.7 2.00 50.8 26.34 1

254 28.88 733 25.50 648 0.50 12.7 2.00 50.8 28.20 1

264 30.00 762 26.50 673 0.50 12.7 2.00 50.8 30.12 1

274 31.12 791 27.50 699 0.50 12.7 2.00 50.8 32.31 1

284 32.25 819 28.50 724 0.50 12.7 2.00 50.8 34.36 1

292 32.25 819 29.25 743 0.50 12.7 2.00 50.8 29.30 1

Flange material Service temperature Sealring material Sealring PTFE colour

Carbon steel -50 to +250 C Carbon steel / low alloy steel Blue

Stainless steel -50 to +250 C Duplex Yellow

Stainless steel -101 to +250 C 17/4-PH Orange

Stainless steel -196 to +100 C Austenitic (eg. 6Mo, 316) Red

SS/Nickel alloy/CS with inlay -196 to +250 C Nickel alloy (eg. 625, 718) Black

All high temp. steel >+250 C Suitable Uncoated

SealringSize

Outside Diameter Inside Diameter Rib Thickness Overall Thickness Sealring Weig

A B C D

ins mm ins mm ins mm ins mm Lbs K

Clamp coatings

Zinc rich, galvanising and epoxy coatings are available for clamp use and applied to recognised industry standards.Procedures and

specifications are available on request. Other specific coatings are available on request.


22/34

Test Rings (RIT)Vector has developed a means of testing a Techlok clamp connector joint in-situ

prior to, or in place of a line leak test to save time and ensure seal integrity.

There are two forms of test ring, an independent ring or an integral part of the

sealring.

The separate Reverse Integrity Test Rings (RIT) acts as a sealing carrier which eas

the installation process of the sealring during the assembly by testing the lips of the

sealring the wrong way hence producing a very onerous test on the seal. The

principle is illustrated below.

Materials

The materials used for the separate RIT rings are high strength carbon steel or 6stainless.

The integral RIT sealrings will complement the base sealring material.

External pressure limits for Techlok sealrings

Tests and calculations indicate the external pressure capacity of standard Techlok

Sealrings (see Graph). The external pressure limit is dictated by the sealring geome

and is therefore independent of the line pressure.

Two types of testing are shown (i.e. the integral RIT Ring and the independent R

Ring), and the pressure limit for both are relatively constant across the sealring range

22

ReverseIntegrity


23/34

with the integral RIT Ring having the higher pressure capacity. Consequently a single

test pressure can be used for either type (see Table).

The test is carried out over a 15 minute period. This allows for any settlement of

oil and trapped air in the system. The small test volume means that even the smallest

leak will result in a pressure loss, ensuring a high integrity test.

The RIT test may also be used for gas testing.

TYPETEST PRESSURE

psi barg

INTEGRAL 2320 160

RIT RINGS 1160 80

Integral RIT / Techlok sealring ready for use Integral RIT / Techlok sealring showing test port

External pressure limits for Techlok sealrin


24/34

24

Solutionsfor demanding applications

Elbows and Tees

Helps facilitate compact piping layouts

Range of elbows, tees and cross pieces available

Manufactured in forged steel with reinforced bend sections

Injection Quills

Specialist sealring quills for inhibitor injection into pipelines

allows controlled amounts of corrosion, scale and wax inhibitor to be released in

the flow

tapered shaft ensures minimum disruption to the fluid flow

installation at regular intervals along the pipeline allows even distribution of theinhibitors

Techlok connectors are highly versatile and can be used in

many diverse applications. In addition there are several

other products completing the Techlok range, some of

which are illustrated on the following pages.

All fittings are available in a selection of materials such as

carbon, low alloy, stainless and Duplex steels, with a full

range of nickel alloys for more specialised applications.

Vector International also offers an individual design service

for special applications.


25/34

Cross-Over Spools

A compact means of joiningone type of pipe connection

to another, or different pipe

sizes

Manufactured from single-piece forgings

Fully compatible with thestandard range of Techlok hubs and sealrings, and is

interchangeable with standard seat profiles

Connects Techlok hub to Techlok hub

Connects Techlok hub to API flange/ANSI flange

Connects Techlok hub to threaded union

Square Flanges

A novel engineeredapproach to flange design

Standard weld prep for

universal piping

connections

Reduced envelope forpiping bundles

Incorporates a standard Techlok metal sealring

Available in all piping materials

Thermowells

Available to monitor flow conditions in pipelines

High-pressure designs allow for thermocouples to be installedwhile fully isolated from internal pressure

Machined integrally with Techlok blind hubs no welding

Can be used in conjunction with Techlok forged tee componentto provide a high-integrity solution

Robust design

Slimline Clamps

Reduced envelopdimensions creates even

more compact

connections

Available in all sizes from1 through to 24

Can be manufactured in carbon steel, stainless, duplex and supeduplex, as well as any other grade required

A streamlined profile that can be used with Pulling Blinds forpositioning of subsea equipment

API Hubs

The full range of API 17D hub components and swivel ring flangconnections are available

Orifice Connectors

The Techlok Orifice Connector is a matched hub pair with orificesealring and clampset

Can be supplied for all pipe sizes and materials

Hubs are accurately drilled and are provided with suitable outletconnections for accurate flow measurement

Special metering spools can be used, employing a separate orifice

plate and integral pressure tappings

Simply connected into the pipe run using streamline bore Techlokconnectors


26/34

26

PowerLok Closure

High integrity sealing forpig launching and receiving

systems

Smaller, lighter, reliableclosure for high pressure

pigging systems

Uses high pressure, metal-to-metal sealring and

clamp technology

Provides weight and space savings

Quick release design for easy and quick opening and closing

No periodic tightening required

Only one operator needed at installation

Standard closures available from 6" to 36" (larger sizes availableon request)

3-Clamp Sets

Available in 30 and largerclamp sizes

Ease of handling andassembly

Available together withslides for easier make-up

and break-out

Designed to client specification and all high-integrity applications

Weld Overlay/Inlay

Carbon and low alloy steelhubs can be furnished with

corrosion-resistant weld

overlay/inlay to prolong hub

life in corrosive

environments such as water

injection lines

The weld overlay/inlay is applied in Alloy 625, and other highgrade alloys, to the critical seat area or, if needed, through the hu

bore

Weld overlay/inlay hubs should be used in conjunction withsuitable high strength stainless steel or nickel alloy sealrings

Twin Torque Gun

Allows fast, controlledtightening of two Techlok

bolts at once

Ensures optimum andequal tension on all bolts

Both bolt pairs on a 6"connector can be

tightened in just one

minute

One gun fits a number of clamp sizes

Solutionsfor demanding applications


27/34

Easilift

Creates safe manoeuvring of blind hubs and clamps offshore

Enables quick and easy lifting, assembly and disassembly of connectors

Sealring is retained in place during assembly

Minimises overall downtime, saving time and money

EasiLift, by Vector International has been designed as the

optimum solution to the continuous challenge of

manoeuvring Techlok blind hubs and clamps, safely and

easily (with health and safety in mind).

EasiLift enables safe assembly and disassembly of blind hub

connections. It is also capable of safely retaining the

sealring during assembly. There are a minimised number of

moving and removable parts to aid reliability and the frame

itself is a rigid, welded structure, tested and certified to

comply with LOLER and PUWER regulations.

This system does not in any way replace any part of the existing assembly and

disassembly procedures for Techlok and is meant to be used only as a blind/clamp

handling system.

EasiLiftLifting Frame


28/34

28

Assemblyand disassembly procedure

AssemblyInspect components prior to assembly

Hub and sealring seating surfaces must be

clean and free from foreign matter. Damage to hub seats

and seal lips is not acceptable, and should be rectified

before assembly.

Lubricate

Usually sealrings are coated which acts as lubricant

during make-up. If required light oil or MoS2 spray can be

used on hub sealing surface but not on sealring. Take care

that no solid particles are present in the lubricant.

Check sealring stand-off

The sealring should rock slightly against hub face.

Stand-off dimensions given below in inches.

Assemble components

Install sealring into the hubs, and assemble clamps

around the hubs. Lubricant applied to the hub/clamp

contact area will aid assembly. The studbolts should be

fitted ensuring that spherically faced nuts locate into

spherical seats of the clamps. Lubrication of nut faces and

bolt threads is recommended.

Tighten bolts in uniform manner

Bolting should be tightened to keep spacing between

clamp halves approximately equal. Clamp segments should

be shocked with suitable soft-faced hammer to

aid assembly. Always re-tighten bolts after shocking to the

torque/preload values given on facing page.

Align hubs

Hubs should be aligned so that sealring can be installed

between hubs. DO NOTattempt to correct badly mis-

aligned piping by clamping force alone; piping pulling forces

should only be released when clamp is fully assembled.

Complete Techlok make up requires two conditions.

1) Hubs must be completely face to face with the rib of

the sealring where standard hubs are used and

completely face to face with each other where recessed

hubs are used.

2) Bolts are made up to the correct torque.

DisassemblyDe-pressurise the line

Always check, never take it for granted that the line has

been de-pressurised. Proceed with caution in case seepage

has caused pressure to build up again.

Slacken nuts but do not remove the nuts from the

bolts - then slacken clamp segments

Gradually run the nuts back along the bolts until just

loose. If clamp segments remain bound onto hubs, then

BOTH segments must be slackened by hitting the inner face

of the clamp lugs with a suitable soft-faced hammer.

Repeat slackening procedure

Re-loosen nuts and re-slacken BOTH clamp

segments until the maximum nut travel shown below

is reached. This should release sealring contact and

any residual pressure will then be released through,

with the joint.

Check clamps are slack and free to rotate

and rock about hubs

Do not proceed until discharge ceases ensure that

hubs are apart, sealring is free to move AND clamps

are slack, free to rotate or rock.

NOTE - If pressure is still in the line, the sealring

might remain seated, making the join`t tight even

though it is part dis-assembled. ONLY when allcomponents are loose and clamps are free to move can

dis-assembly be completed. If the components are not

free to move DO NOT CONTINUE - contact your

supervisor.

Always ask yourself - what if ?

What if, the connection is still under pressure, am I or

others in danger, and if so how?

What if, there is still gas or fluid in the line?

What if, the sling snaps?

What if, the load swings in my direction?

What if, the piping springs upon release? (Piping spring may

also prevent free rotation of clamps around the hubs).


29/34

Techlok designation uses in to denote nominal sizein inches as opposed to GR which denotescomparable products.

All data contained herein may be subject to change

without notice.

Clamp Standard Basic Bolt Preload Basic Bolt TorqueSize Bolt Dia (Note 1, 3) Lubricated =0.1 Notes 2X

(Note 1, 2, 3)ins Lbf KN Ft-lbs Nm ins mm

Standard Clamp Series

1in 0.500 2844 12.7 17 23 4 0.2 511/2 in 0.625 4766 21.2 35 48 4, 5 0.2 62in 0.750 6516 29.0 55 75 4, 5 0.2 63in 0.750 7476 33.3 65 88 4, 5 0.3 84in 0.875 9946 44.2 100 136 4, 5 0.4 105in 1.000 13986 62.2 160 217 4, 5 0.6 146in 1.125 16032 71.3 210 285 4, 5 1.0 248in 1.250 20887 92.9 300 407 4, 5 1.1 27

Light Duty Series

L14in 1.625 39727 177 700 949 4 1.3 33L16in 1.750 42084 187 800 1085 4 1.3 33L18in 1.875 54288 241 1100 1492 4 1.3 33L20in 2.000 58073 258 1250 1695 4 1.3 34L24in 2.250 74880 333 1800 2440 4 1.6 39

Heavy Duty Series

H2in 0.875 9946 44.2 100 136 4, 5 0.2 6H3in 0.875 11931 53.1 120 163 4, 5 0.3 8H4in 1.000 12240 54.4 140 190 4, 5 0.4 11H8in 1.375 25599 114 390 529 4, 5 0.9 24H10in 1.625 39722 177 700 949 4, 5 1.2 32H12in 1.750 47340 211 900 1220 4, 5 1.5 37H14in 1.875 59208 263 1200 1627 4, 5 1.5 39H16in 2.250 83204 370 2000 2711 4, 5 1.6 40H18in 2.250 83204 370 2000 2711 4, 5 1.7 42H20in 2.250 89448 398 2150 2915 4, 5 1.7 43H22in 2.250 89448 398 2150 2915 4, 5 1.7 43H24in 2.250 93608 416 2250 3051 4, 5 1.8 45H26in 2.500 103590 461 2750 3728 4, 5 1.8 45

Notes:1. This is the basic minimum torque/preload value. Use for typically 900lb systems and below, blind closures and Stainless Steel clamps.2. Different friction coefficients will require the torque values to be adjusted. Check with Lubricant manufacturer.3. Exceeding the stated torque/preload values may cause distortions in the Clamp/Hub. If these torques do not achieve correct make-up (i.e. unable to correct mis-alignment),

then seek assistance as other measures may be needed to assist with the assembly.4. Factor torque by 1.5 for mis-aligned piping and/or 1500lb systems and above. Suitable only for Carbon, Duplex and Low Alloy Steel Clamps with B7 or equivalent bolts.5. Factor torque by 2.0 for extreme mis-aligned piping and/or 2500lb (and 5000psi) systems and above. Suitable only for Low Alloy Steel Clamps with Grade B7 bolts or equivalent.

Sealring Nominal MinStand-off CantedCanted for Re-use

4 0.018 0.0065 0.018 0.0067 0.021 0.007

11 0.025 0.00912 0.025 0.00913 0.025 0.00914 0.024 0.00816 0.024 0.00920 0.023 0.01123 0.025 0.01325 0.028 0.01427 0.032 0.01631 0.031 0.01534 0.036 0.018

40 0.039 0.01942 0.042 0.02146 0.050 0.02552 0.050 0.02556 0.053 0.02662 0.092 0.04664 0.096 0.04867 0.096 0.04872 0.099 0.05076 0.103 0.05282 0.107 0.05384 0.111 0.05587 0.114 0.05791 0.118 0.05992 0.118 0.05994 0.122 0.06197 0.129 0.065102 0.129 0.065106 0.137 0.068112 0.144 0.072

116 0.148 0.074120 0.155 0.078122 0.155 0.078124 0.152 0.076130 0.167 0.083134 0.167 0.083137 0.163 0.081140 0.167 0.083144 0.193 0.096152 0.189 0.095160 0.193 0.096170 0.200 0.100180 0.207 0.104185 0.219 0.109192 0.230 0.115200 0.234 0.117210 0.224 0.112220 0.254 0.127225 0.261 0.130232 0.272 0.136

Standard Clamp SeriesClamp GR Standard GR OptionalSize Sizes Sizes

1in 1GR

11/2 in 1.5GR

2in 2GR

3in 3GR

4in 4GR

5in 5GR E

6in 6GR F,XF

8in 8GR X8GR

Light Duty Clamp Series

Clamp GR Standard GR OptionalSize Sizes Sizes

L14in X14GR

L16in X16GR

L18in X18GR

L20in X20GR

L24in X24GR

Heavy Duty Clamp Series

Clamp GR Standard GR OptionalSize Sizes Sizes

H2in BH3in CH4in DH8in G XGH10in 10H X10HH12in 12M X12MH14in PH16in SH18inH20in UH22in V H24in W

H26in Y

Torque/preload values for the Techlok Clamp Connector Sealring stand-off

Cross reference tables


30/34

in the field

Techlok

30

Training Services

We can offer comprehensive training courses for a ll relevant personnel at site pr

to their commencing work on the installation/assembly of any Vector product.

Satisfactory completion of the course leads to the award of a competency

certificate.

Site Services

Our Product Support Engineers are available on site at a time when your sitecrews are ready to assemble and install piping runs. These engineers will assist in t

identification and repair of potential issues which may ultimately lead to a possible le

at Hydro-test.

Remember prevention involves less cost than repairs, especially offsho

Leak Reduction Initiative

We offer and provide a full and comprehensive on site service which delivers all

the benefits associated with both initiatives indicated above, and much more

Our leak reduction initiative is designed to save you significant time and money

including minimising expensive offshore rework and potential lost production days.

The overall benefits of our leak reduction initiative more than justify the costs.

Vector International supply far more than just piping

products. In recent years we have become well known for

our Product Support Services and our support for your

project, no matter how large or small, never ends. Our

intention is for you to have a very successful experience

working with us and our products.

These services are charged to you but in the medium term

will save you time, effort and money and will also prevent

frustrations at installation for you and your staff.

It is a well known statistic that a number of mechanical

joints, e.g. flanges, may show signs of leakage at start up

(Hydro-test). With the input of our Product Support

Teams, this risk can be eliminated.

Typical damage caused through mis-handling


31/34

Keep all the information you need about the Techlok Clamp Connector at hand with

this useful mini CD, or copy the contents to your PC or laptop for instant access.

CD Contents

Design principles

Hub dimensions

Clamp dimensions

Sealrings dimensions and selection

Pressure temperature ratings

Weight comparisons

Materials and size selection

Installation procedure

Case studies

Picture gallery

Techlok Clamp Connector

High performance, competitive price andgreater efficiency

Low-weight: typically 75% weightsaving when compared to

conventional flanges

Reduced bolting requirements -just four bolts

Radial bolting allows 360orientation around the pipe

Quick and easy make-up andbreak-out

Easier fabrication, no bolt holes to align

Techlok does not rely on complex bolting tomaintain seal integrity, but offers the strength of a

welded joint

The preferred solution where space, weight and jointintegrity are critical

Clamp Connector


Techlok


32/34

TechlokDimensionalreferencechart

Butt Weld HubBlind Hub

Clamp


33/34

TBlind Hub

A four-bolt pipe connector typically

weighing 75% less than a comparable

standard ANSI or API flange

Available in 1/2 to 26


34/34

The above international dialling codes may be subject to change when calling from within the country.

E-mail: [email protected] Web: www.vectorint.com

AustraliaTel: +61 8 9471 1907

AmericasTel: +1 713 979 4444

MalaysiaTel: +603 238 00060

Middle EastTel: +971 435 56966

NetherlandsTel: +31 77 352 8200

NorwayTel: +47 32 20 93 00

UK AberdeenTel: +44 1224 775 242

UK BaglanTel: +44 1639 822 555

worldwidepresence

This brochure is for information only. For more detailed information please view our website at www.vectorint.com.All details and measurements are correct at time of print.

Despite every effort, the information contained in this brochure may not be comprehensive, it may not be accurate, up to date or applicable to the circumstances of any particular application or enquiry. We cannot accept any liabilitinaccuracies or omissions or changes which may take place to product technical specification due to third parties. Vector International does not accept liability for any direct, indirect, special, consequential or other losses or dama

whatsoever kind arising out of access to or the use of this brochure or any information contained in it

Send for your desktop model now anfirst step to greater reliability, email techlok@vec

TEC

Other Vector products

vector tecklok catalog

Documents

techlok clamp connectors

techlok joints

clamp bolts

techlok clampconnectors

conventional ansi flanges

api flanges

conventional flanges

bolt pipe connector