using the avid mojo dnaresources.avid.com/supportfiles/attach/using_mojodna_0606301a.pdf · avid...
TRANSCRIPT
Using the Avid Mojo DNA
Important Information
Avid® recommends that you read all the information in these installation instructions thoroughly before connecting or using your new hardware.
This document explains how to use and connect cables and devices to the Avid Mojo™ Digital Nonlinear Accelerator (DNA) and how to connect specific devices to an Avid-supported PC or Macintosh® system that the Avid Mojo DNA is connected to. The supported PC and Macintosh systems used with your Avid Mojo DNA can change at any time.
n Please look at the ReadMe file that installs with the application. It contains important information that is used in conjunction with the information presented in this document.
Contents
If You Need Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Avid Mojo DNA Front and Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Avid Mojo DNA Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Avid Mojo DNA Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Synchronizing Audio and Video Equipment . . . . . . . . . . . . . . . . . . . . . . . 9
Power-On Self-Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
a
Using the Avid Mojo DNA
2
1394 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting Peripheral Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting Audio Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connecting S-Video or DV Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting a Client Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting a Video Deck — Composite Signal . . . . . . . . . . . . . . . . . . 15
Connecting a Video Deck — Component Signal. . . . . . . . . . . . . . . . . . 16
System Connections and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting the Application Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HP xw8000 System Slot Configuration and Connections . . . . . . . . . . . 19
Macintosh G4 System Slot Configuration and Connections . . . . . . . . . 21
Macintosh G5 System Slot Configuration and Connections . . . . . . . . . 22
Connecting Serial and MIDI Port Devices . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USB and Serial Differences Between Windows and Macintosh Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting the USB Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connecting the USB Devices to the USB Hub . . . . . . . . . . . . . . . . . . . 25
Connecting the USB-to-Serial Adapter . . . . . . . . . . . . . . . . . . . . . . 25
Connecting the USB-to-MIDI Converter . . . . . . . . . . . . . . . . . . . . . 26
Connecting JL Cooper Fader Controllers . . . . . . . . . . . . . . . . . . . . . . . 27
Connecting the Yamaha 01V Mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Controlling a Video Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SCSI Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1394 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Internal IDE Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ethernet Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fibre Channel Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
If You Need Help
3
Formatting and Striping MediaDrives (Windows) . . . . . . . . . . . . . . . . . . 33
Formatting and Striping MediaDrives (Macintosh) . . . . . . . . . . . . . . . . . 34
Using Striped Drives on Mac OS X and Mac OS 9.x Systems . . . . 34
Moving Striped Drives to Another System (Macintosh Only). . . . . . 35
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Regulatory and Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
FCC Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Canadian ICES-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
European Union Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Australia and New Zealand EMC Regulations . . . . . . . . . . . . . . . . . . . . 41
Technical Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
If You Need Help
If you are having trouble using Avid Mojo DNA:
1. Retry the action, carefully following the instructions given for that task. It is especially important to check each step of your workflow.
2. Check these installation instructions for the latest information that might have become available after the documentation was published.
3. Check the documentation that came with your Avid application or your hardware for maintenance- or hardware-related issues.
4. Visit the online Knowledge Center at www.avid.com/support. Online services are available 24 hours per day, 7 days per week. Search this online Knowledge Center to find answers, to view error messages, to access troubleshooting tips, to download updates, and to read or join online message-board discussions.
5. For Technical Support, please call 800-800-AVID (800-800-2843).
For Broadcast On-Air Sites and Call Letter Stations, call800-NEWSDNG (800-639-7364).
Using the Avid Mojo DNA
4
Symbols and Conventions
These installation instructions use the following symbols and conventions:
Overview
The Avid Mojo DNA is designed to capture and output analog media and digital media (DV 25) using digital decks and cameras.
The Avid Mojo DNA is powered by an autosensing power adapter that plugs into a wall plug or power strip.
The Avid Mojo DNA accepts video and audio in different formats and resolutions, up to and including Avid broadcast standard 1:1 uncompressed. These formats and resolutions are changed to Avid-specific data for transfer to the Avid editing system over a 1394 cable. The data transfer uses an Avid-specific protocol that describes the format and resolution of the data being input.
You then edit the data on the Avid editing system and return it to the Avid Mojo DNA to be changed back to the proper format and resolution as needed for video and audio output.
n To capture and play 1:1 video, you must have an Avid Mojo DNA connected to your system. Disconnecting the Avid Mojo DNA results in a “Wrong Format” error message for 1:1 clips. However, without an Avid Mojo DNA attached, you can transcode your 1:1 video clips to DV 25 or 15:1s. For more information, see “Using the Transcode Option” in the Help.
Symbol or Convention Meaning or Action
n A note provides important related information, reminders, recommendations, and strong suggestions.
c A caution means that a specific action you take could cause harm to your computer or cause you to lose data.
w A warning describes an action that could cause you physical harm. Follow the guidelines in this document or on the unit itself when handling electrical equipment.
Avid Mojo DNA Front and Rear Panel
5
The Avid Mojo DNA consists of:
• The Avid Mojo DNA
• A stand
• A power adapter with power cord
Also included in the kit is a 6-pin to 6-pin 1394 cable that connects the Avid Mojo DNA to the Avid editing system platform and a Using the Avid Mojo DNA CD-ROM.
You can also order a special adapter cable from Avid that allows you to send a component signal into or out of the Avid Mojo DNA using both the S-Video and composite connectors at the rear of the Avid Mojo DNA. See “Connecting a Video Deck — Component Signal” on page 16 for more information.
Avid Mojo DNA Front and Rear Panel
You can place the Avid Mojo DNA in a stand or position it on its side. The Avid Mojo DNA turns on when you connect the power adapter. You attach cables to connect the power, the system, and external devices at the rear.
Avid Mojo DNA in the Stand
Rear
Stand
Front panel
Using the Avid Mojo DNA
6
Avid Mojo DNA Front Panel
The Avid Mojo DNA front panel contains function LEDs behind a cover, a headphone jack, and volume control for the headphones (see the following figure).
n The function LEDs are not labeled on the front panel. You can see the function names through the cover when it is lit.
Avid Mojo DNA Front Panel
The following table shows the name of each LED and describes its function.
CLIP 48KHZ DV REF HOST POWER
Headphone jack Volume controlLEDs
LED Functions
LED Function
Clip Flashes red as audio data is lost (due to overloading or peaking), and for power-on self-test (POST). See “Power-On Self-Tests” on page 10.
48KHz Lit when 48-KHz audio is selected in the application; not lit when 44 KHz or 32 KHz is selected.
DV Lit when DV input is selected in the application.
Ref Lit when the Avid Mojo DNA is synced to a reference video source. See “Synchronizing Audio and Video Equipment” on page 9.
Host Lit when the Avid Mojo DNA is connected to the Avid editing system.
Power Lit when the power adapter is connected to the Avid Mojo DNA.
Avid Mojo DNA Front and Rear Panel
7
Avid Mojo DNA Rear Panel
The following figure shows the connections on the rear of the Avid Mojo DNA, while the following table describes the function of each connector. The rear connectors are labeled on the device.
Avid Mojo DNA Rear Panel (SD video and Audio Boards)
Although not labeled as a Component connection, Avid has created a custom option cable that connects to the S-Video and Composite input connectors allowing you to input a Component signal into the Avid Mojo DNA. This cable can also be used to output a Component signal when connected to the S-Video and Composite output connectors. Connectors are described in the following table.
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
Host
DV
Ref input S-Video input
Composite video input (yellow)
Audio/Clock output (left, white)
Audio output(right, red)
Composite video output (yellow)
S-Video output
DC InAudio input(left, white)
Audio input(right, red)
Avid Mojo DNA Rear Connectors
Label Function
Host A 6-pin 1394 connector used to input and output audio and video signals to and from the Avid editing system.
DV A 4-pin 1394 connector used for input and output to and from a DV camera or deck and the Avid Mojo DNA.
REF (Reference) Input An RCA® connector that provides an input connection for a black burst generator or house sync; synchronizes the timing of incoming video signals between the Avid editing system and the equipment connected to it.
Using the Avid Mojo DNA
8
Video Input A 4-pin S-Video connector and an RCA connector that allow you to input video signals to the system.
S-Video and Composite video connectors are used to connect the analog video outputs of a video camera or deck.
Component Input An optional cable (purchased separately) that uses the S-Video and the Composite video input connectors, allowing you to input a Component signal; connects to the analog video output of a deck.
Audio Input Two RCA connectors used for the left and right Audio input signals; connect to an analog audio output of a video camera or deck.
Audio Output
CLK (Clock)
Two RCA connectors used for the left and right Audio output signals; connect to an analog audio input of a video camera or deck.
An RCA connector which provides a digital synchronous output when connected to the Digidesign® Digi 002; connects to the S/PDIF input of a Digi 002. The analog audio output signal changes to a digital syncs signal when connected to an Avid Xpress® Studio.
Video Output A 4-pin S-Video connector and an RCA connector that allow you to output video signals to a video camera or deck.
S-Video and Composite video connectors are used to connect the analog video inputs of a video camera or deck.
Component Output An optional cable (purchased separately) that uses the S-Video and the Composite video output connectors, allowing you to output a Component signal; connects to analog video input of a video deck or monitor.
Power Connects to the power adapter.
Avid Mojo DNA Rear Connectors (Continued)
Label Function
Avid Mojo DNA Front and Rear Panel
9
Synchronizing Audio and Video Equipment
Avid editing systems require synchronization (sync) when capturing audio and video. A sync signal for analog audio and analog video can also be generated from the connected REF signal, from incoming video, or internally by the Avid Mojo DNA.
n The digital signal from a 1394 device has its own sync signal to which the Avid Mojo DNA synchronizes.
n The audio output connector (labeled CLK) provides a digital sync signal when connected to the Digidesign Digi 002 in an Avid Xpress Studio.
The following list summarizes how sync works:
• Video Reference IN (REF) — Sync signals are generated from the incoming black burst generator (BBGen) or from a house sync. If there is no sync connected to REF, an internal sync is used.
n By default, the sync signal is generated from incoming video whenever you capture analog video. Depending on the configuration of the audio and video equipment attached to the Avid Mojo DNA, you might need to use a BBGen or house sync, for example, when you perform an Insert Edit.
• Incoming video signal — When you capture video, a sync signal is generated by the Avid Mojo DNA from the incoming video: component, composite, S-Video, or DV.
When you capture analog video and audio, the Avid Mojo DNA generates a sync signal from the incoming video, but it does not sync your video to your audio. You must sync these externally to the Avid Mojo DNA.
• Incoming analog audio — When you capture audio only, the Avid Mojo DNA does not sync to the incoming audio. You should use an external sync in this case.
Using the Avid Mojo DNA
10
Power-On Self-Tests
The Avid Mojo DNA runs power-on self-tests (POSTs) to determine if the box and the board within the box are operating properly each time you turn the Avid Mojo DNA on.
If a failure occurs when running a POST, the Clip LED (see “Avid Mojo DNA Front Panel” on page 6) blinks steadily once a second. Also, if the Power LED does not light after you connect the Avid Mojo DNA to the power adapter, the Avid Mojo DNA is not capable of running diagnostics and is not functioning properly. If possible, try another power adapter. If the Avid Mojo DNA does not work with a different power adapter, replace the Avid Mojo DNA.
1394 Requirements
The rear of the Avid Mojo DNA has a 4-pin DV connector used for connecting cameras, decks, or other video devices for input or output. The 4-pin DV connector does not support 1394 (FireWire) drives. For connector locations see, “Avid Mojo DNA Rear Panel” on page 7.
n Macintosh systems more commonly use the term FireWire, where Windows systems use the IEEE term of 1394.
n The multiple FireWire connectors on Macintosh systems are on the same bus. You must install a separate 1394 board in Macintosh and Windows systems if you want to attach 1394 drives.
Cable
The IEEE 1394 cabling standard requires that IEEE 1394 (FireWire) devices be within 14.76 ft (4.5 m) of the next bus connector. When you connect a FireWire device (drive, camera, or deck), your FireWire cable must not exceed this length. Avid products do not support the use of IEEE 1394 (FireWire) repeaters to boost or extend the signal to the device.
In addition, Avid does not support any type of cable extender or FireWire hub between the Avid editing system connection and the Avid Mojo DNA. If the Avid editing system does not sense a direct connection to the Avid Mojo DNA, the Avid Mojo DNA enters a non-operating mode.
Connecting Peripheral Equipment
11
Devices
1394 (FireWire) decks and cameras that are connected to the Avid Mojo DNA must be turned on after the Avid Mojo DNA. Avid recommends you turn on your Avid editing system and start the Avid editing application as follows:
To turn on an Avid editing system with a 1394 (FireWire) device:
1. Turn on the system.
2. Turn on the Avid Mojo DNA.
3. Turn on the 1394 (FireWire) device.
n Although some devices appear to be turned off, they can still send data over the 1394 bus. Many support a standby mode. To ensure the device is off, disconnect the power cord.
4. Start the Avid editing application.
Connecting Peripheral Equipment
There are several possible cabling configurations depending on your camera, video deck, and client monitor. The audio and video output signals are available to each output connector at the same time. Video and audio cables are not included with the Avid Mojo DNA. Avid provides optional video cables that use the S-Video and Composite video connectors for a component connection to your deck. The following sections describe several possible connections:
• Connecting Audio Signals
• Connecting S-Video or DV Signals
• Connecting a Client Monitor
• Connecting a Video Deck — Composite Signal
• Connecting a Video Deck — Component Signal
• Controlling a Video Deck
Using the Avid Mojo DNA
12
Connecting Audio Signals
Audio input and output connections on the rear of the Avid Mojo DNA use standard RCA connectors. Audio connections require the following:
• Four audio cables with RCA connectors on both ends of the cable. You can also use audio cables with RCA connectors on one end and XLR connectors on the other end.
• A video deck or audio device with audio input and output connections.
To connect your audio to a deck or audio device:
1. Attach two audio cables to the Audio input connectors (see the following figure):
n Your cables might be color-coded with red and white connectors. If so, match the colors on the RCA connectors with the color of the inputs on the Avid Mojo DNA.
n If you have RCA-to-XLR connectors on your audio cables, you must pay attention to the male and female XLR connections attached to your audio device.
a. Connect an RCA connector to the red Audio input connector on the Avid Mojo DNA.
b. Connect an RCA connector to the white Audio input connector on the Avid Mojo DNA.
Connecting Peripheral Equipment
13
2. Attach the other end of the audio cables (or XLR connectors) to Audio output connectors on your deck or audio device.
Connecting Audio to the Deck
3. Attach two more audio cables to the Audio output connectors (see the preceding figure):
a. Connect an RCA connector to the red Audio output connector on the Avid Mojo DNA.
b. Connect an RCA connector to the white Audio output connector on the Avid Mojo DNA.
4. Attach the other end of the last two audio cables (or XLR connectors) to Audio input connectors on your deck or audio device.
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
Audio input (white) Audio output (red)
To Audio input on the deck or audio device
Audio input (red) Audio output (white)
To Audio output on the deck or audio device
RCA jack to RCA jack cable
XLR connector to RCA jack cable
Using the Avid Mojo DNA
14
Connecting S-Video or DV Signals
The S-Video and DV connectors on the rear of the Avid Mojo DNA use industry-standard connectors. The connections are as follows:
• There are two S-Video connectors on the rear of the Avid Mojo DNA. One connector is for video input, and the other is for video output. The following figure identifies the connectors.
• The DV connector uses a 4-pin 1394 cable that carries the video and audio input and output signals to and from your DV device. You can also use a 4-pin to 6-pin DV cable if your DV device uses a 6-pin connector. The following figure identifies the connector. Device control is supported through the 4-pin DV connection.
Connecting S-Video or DV to the Deck
Connecting a Client Monitor
To view the video as it passes through the Avid Mojo DNA, you might want to connect a monitor. You have two options:
• Most video decks provide a video output connector. You can connect a monitor to the deck to see the video sent to the Avid Mojo DNA or the video the Avid Mojo DNA sends to the deck. See your video deck manufacturer’s documentation for more information.
c The video you see in the monitor connected to the deck might not indicate there is a video signal going to the Avid Mojo DNA.
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
4-pin DV S-Video input S-Video output
Connecting Peripheral Equipment
15
• You can see the input and output video signals passing through the Avid Mojo DNA using the Composite video output connector on the rear of the unit. Connect a composite monitor to the connector identified in the following figure.
Connecting a Composite Monitor
Connecting a Video Deck — Composite Signal
A composite video deck connection requires the following:
• Two composite video cables with RCA connectors on each end
• A video deck or camera with composite inputs and outputs
To connect a deck or camera using composite signals:
1. Locate one composite video cable.
2. Connect the RCA connector to the yellow Composite video input connector on the Avid Mojo DNA (see the following figure).
Connecting a Video Deck — Composite Signal
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
Composite video output
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
To composite in on the deck or camera
To composite out on the deck or camera
Composite video input (yellow)
Composite video output (yellow)
Using the Avid Mojo DNA
16
3. Connect the other end of the composite cable to Composite output of your video deck or camera.
4. Locate another composite video cable and connect the RCA connector to the yellow Composite video output connector on the Avid Mojo DNA (see the previous figure).
5. Connect the other end of the composite cable to Composite input of your video deck or camera.
n Make sure you terminate the input signal if your video deck supports passthrough. See the documentation provided with your video deck.
n The Avid Mojo DNA automatically terminates incoming video signals.
Connecting a Video Deck — Component Signal
An optional component video deck connection requires the following:
• Two Avid Mojo DNA component video cables
• A video deck with component inputs and outputs
To connect a deck using component signals:
1. Locate a component video cable (see the following figure).
There are three BNC connectors on one end of the cable; the other end has an RCA connector and an S-Video connector.
Optional Component Cable
S-Video connector
Three component BNC connectors for the deck connection
Composite video RCA connector
Connecting Peripheral Equipment
17
2. Attach the RCA and S-Video end of the cable to the Avid Mojo DNA inputs as follows (see the following figure):
a. Connect the RCA connector to the yellow Composite video input connector on the Avid Mojo DNA.
b. Connect the S-Video connector to the S-Video input connector on the Avid Mojo DNA.
Connecting a Video Deck — Component Signal
3. Attach the other end of the component cable (with the three BNC connectors) to Component output of your video deck as follows:
a. Connect the BNC attached to the green wire to the component output connector labeled Y.
b. Connect the BNC attached to the red wire to the component output connector labeled Pr.
n The component connectors on your deck might be labeled differently, for example; Y, Cr, and Cb or Y, R-Y, and B-Y.
c. Connect the BNC attached to the blue wire to the component output connector labeled Pb.
HostDV
Ref Video
Audio Audio Video DC
INInput OutputCLK
S-Video input S-Video output
To component in on the deck
Composite video input Composite video output
To component out on the deck
Using the Avid Mojo DNA
18
4. Locate another component cable and attach the RCA and S-Video end to the Avid Mojo DNA outputs as follows (see the previous figure):
a. Connect the RCA connector to the yellow Composite video output connector on the Avid Mojo DNA.
b. Connect the S-Video connector to the S-Video output connector on the Avid Mojo DNA.
5. Attach the other end of the component cable (with the three BNC connectors) to Component input of your video deck as follows:
a. Connect the BNC attached to the green wire to the component input connector labeled Y.
b. Connect the BNC attached to the red wire to the component input connector labeled Pr.
c. Connect the BNC attached to the blue wire to the component input connector labeled Pb.
n Make sure you terminate the input signal if your video deck supports passthrough. See the documentation provided with your video deck.
n The Avid Mojo DNA automatically terminates incoming video signals.
System Connections and Configurations
The Avid Mojo DNA has been qualified with the following PC and Macintosh products, which are used as examples in this document:
• HP® Workstation xw8000
• Apple® FireWire 800 dual 1.42-GHz PowerPC® G4 system
• Apple dual 1.6-, 1.8-, and 2-GHz PowerPC G5 system
The 2.4 GHz Mobile P4 Dell Latitude C840 and the 1.33-GHz Apple PowerBook® G4 17-inch are also qualified for use with the Avid Mojo DNA, but they are not used as examples in this document. You might need to provide a 6-pin to 4-pin cable for use with your Dell Latitude C840.
As more systems and third-party boards are tested and qualified, and as different configurations are approved, they will be placed on the Avid web site. Go to www.Avid.com/Products/Avid_application for the latest information concerning system availability.
System Connections and Configurations
19
Connecting the Application Key
The application key (see the following figure), commonly referred to as a dongle, allows the Avid software to run on your system. If you have not yet connected the application key, you should do so before you run the Avid application. When given a choice, Avid recommends you connect the application key to one of the USB ports at the rear of the system (as apposed to the front).
Application Key
HP xw8000 System Slot Configuration and Connections
Avid has qualified the HP xw8000 system with the NVIDIA® Quadro®4 980 XGL graphics board to be used with the Avid Mojo DNA. Other PC systems and graphics boards might be qualified at a later date.
The following table lists the Avid-qualified slot configuration for the xw8000 system. The following figure identifies the slots and connections on the rear of the xw8000 system.
c The ATTO™ 3300 and 3305 Fibre Channel boards are designed for 100 MHz PCI-X bus slots. If these Fibre Channel boards are installed into a PCI-X 133 MHz bus slot, you will experience data corruption and data loss. Make sure you install ATTO 3300 or 3305 Fibre Channel board in a PCI-X slot that runs at 100 MHz or less.
Using the Avid Mojo DNA
20
Rear View of xw8000 System
HP Workstation xw8000 Slot Assignments
Slot Description
AGP slot Qualified OGL graphics board
PCI slot 1 (32-bit, 33 MHz, 5 V) Do not use. (This bus segment is used by the integrated 1394 and the integrated Ethernet.)
PCI slot 2 (32-bit, 33 MHz, 5 V) Do not use. (This bus segment is used by the integrated 1394 and the integrated Ethernet.)
PCI-X slot 3 (64-bit, 133 MHz, 3.3 V) (Option) Avid Unity™ LANshare EX or Avid Unity PortServer gigabit board or second 1394 board. See “Ethernet Support” on page 32 for more Ethernet information.
c Do not install the ATTO 3300 or 3500 Fibre Channel board in this slot.
n If you install a second 1394 (FireWire) board, make sure that it is a Universal board. Universal boards can operated at 5 volts and at 3.3 volts.
PCI-X slot 4 (64-bit, 100 MHz, 3.3 V) Available slot
PCI-X slot 5 (64-bit, 100 MHz, 3.3 V) (Option for Avid NewsCutter XP) Fibre Channel board to Avid Unity system or Fibre Channel board to playback device
Keyboard and mouse
USB ports
LAN connection
AGP Slot
PCI Slots
MicrophoneLine OUT
Line IN
Channel A SCSI connector
Serial portParallel port
Channel B SCSI connector
12345
1394 6-pin connection
System Connections and Configurations
21
Macintosh G4 System Slot Configuration and Connections
Avid has qualified the G4 system with the NVIDIA GeForce™4 Titanium graphics board to be used with the Avid Mojo DNA. Other Macintosh systems and graphics boards might be qualified at a later date.
The following table lists the Avid qualified slot configuration for the Macintosh G4 system. The following figure identifies the slots and connections on the rear of the Macintosh G4 system.
Rear View of G4 System
G4 Slot Assignments
Slot Description
PCI slot 5 (64-bit, 33 MHz, 5 V) Available slot
PCI slot 4 (64-bit, 33 MHz, 5 V) (Option) Avid Unity LANshare EX or Avid Unity PortServer gigabit board or second 1394 FireWire board
PCI slot 3 (64-bit, 33 MHz, 5 V) (Option) SCSI UL3D or Fibre Channel board to Avid Unity system
PCI slot 2 (64-bit, 33 MHz, 5 V) (Option) SCSI UL3D or Fibre Channel board to Avid Unity system
AGP slot 1 Apple graphics board
5
4
3
2
1
Slot 5
Slot 1 Apple graphics board
USB ports
FireWire 6-pin connections
Audio connections
Using the Avid Mojo DNA
22
Macintosh G5 System Slot Configuration and Connections
The following table lists the Avid qualified slot configuration for the Macintosh G5 system. The following figure identifies the slots and connections on the rear of the Macintosh G5 system.
Rear View of G5 System
G5 Slot Assignments
Slot Description
PCI-X slot 4 (64-bit, 133 MHz, 3.3 V) (Option) Second 1394 FireWire board or SCSI UL4D
PCI-X slot 3 (64-bit, 100 MHz, 3.3 V) (Option) Fibre Channel board to Avid Unity system
PCI-X slot 2 (64-bit, 100 MHz, 3.3 V) (Option) SCSI UL3D
AGP slot 1 Apple graphics board
Slot 4
Slot 1 Apple graphics board
USB ports
Ethernet connection
Audio connections
FireWire 400, 6-pin connection
FireWire 800, 9-pin connection (1394B)
Modem connection
Connecting Serial and MIDI Port Devices
23
Connecting Serial and MIDI Port Devices
Avid systems support the connection of two different MIDI fader controllers and a Yamaha® 01V mixer. The fader controllers and the 01V mixer connect to the MIDISPORT™ 2x2 USB-to-MIDI converter attached to the USB ports. The two fader controllers are the JL Cooper FaderMaster Pro™ and the JL Cooper MCS-3000X. Avid supports recording automation gain using the MIDI features of the 01V mixer. This section contains:
• USB and Serial Differences Between Windows and Macintosh Systems
• Connecting the USB Hub
• Connecting the USB Devices to the USB Hub
• Connecting JL Cooper Fader Controllers
• Connecting the Yamaha 01V Mixer
• Controlling a Video Deck
USB and Serial Differences Between Windows and Macintosh Systems
If you have a Windows system, you likely have 2 or more USB connections and one serial connection. If you need more than one serial connection, Avid recommends using a USB-to-serial adapter. See the documentation that comes with the device.
If you have a Macintosh system, you might have two USB connectors and no serial ports. Avid suggests you attach a USB hub to the rear of the system and use a Keyspan Twin USB-to-serial adapter (Macintosh only) for deck control.
Connecting the USB Hub
The USB hub explained in this section converts one USB port into seven USB ports. The USB hub kit (see the following figure) contains a USB hub, a power adapter, and a USB cable.
n The USB hub shown in the example might not be the actual USB hub you use. However, the example shown provides enough information to allow you to properly connect whatever USB hub you decide to use.
n The USB hub is supported only when it is powered by an ac adapter.
Using the Avid Mojo DNA
24
The USB hub has the following connections:
• USB ports 1 through 7
• Device connection
• On/Off switch
• Power connection
USB Hub
To connect the USB hub:
1. Connect the power adapter to the USB hub:
a. Plug the dc connector of the ac power adapter into the USB hub power connection.
b. Plug the ac power adapter into a wall outlet or power strip.
2. Connect the USB hub to the system using the USB cable:
a. Plug the device connector of the USB cable into the device connection at the rear of the USB hub.
b. Plug the USB connector of the USB cable into one of the USB ports at the rear of the system.
3. Turn on the power.
Power connection
USB hub
DC connector AC power adapter
USB cable
USB connector
USB ports
Device connection
On/Off switch
Device connector
Connecting Serial and MIDI Port Devices
25
Connecting the USB Devices to the USB Hub
Once the USB hub is connected to the system, you can connect the following USB devices to the USB hub:
• USB-to-serial adapter
• USB-to-MIDI converter
Connecting the USB-to-Serial Adapter
The USB-to-serial adapter connects to a USB port on the USB hub (see the following figure).
USB-to-Serial Adapter
To connect the USB-to-serial adapter to the USB hub:
1. Plug the USB-to-serial adapter cable into a USB port on the USB hub (see “Connecting the USB Hub” on page 23 for port locations).
2. Install the USB-to-serial adapter software, using the instructions that came with the USB-to-serial adapter.
USB-to-serial adapter cable
Using the Avid Mojo DNA
26
Connecting the USB-to-MIDI Converter
Avid recommends the use of the MIDISPORT 2x2 USB-to-MIDI converter connected to a USB hub for the Macintosh systems or to a USB port on a PC (see the following figure).
Connecting the USB-to-MIDI Converter
n The ReadMe file and the Help in your application explain how to install the drivers and configure the USB-to-MIDI converter.
To connect the USB-to-MIDI converter to a port on the USB hub:
1. Locate the MIDI converter USB cable.
2. Connect the device connector of the USB cable to the device connector on the USB-to-MIDI converter.
3. Connect the other end of the USB cable to a USB port on the USB hub (see “USB Hub” on page 24 for a port location).
4. Push the USB/MIDI Thru button in to allow the device to function as a USB-to-MIDI converter (see the following figure).
USB-to-MIDI Converter Front Panel
USB connector
USB-to-MIDI converter USB cable
Device connector Device connector
IN A
IN A IN B
OUT A OUT B
USB/MIDIThru
USB
Button (In position)
Connecting Serial and MIDI Port Devices
27
Connecting JL Cooper Fader Controllers
Your Avid system supports the FaderMaster Pro and the MCS-3000X fader controllers. Both of the fader controllers connect to a USB-to-MIDI converter that connects to a USB port on the system. See your Avid editing application Help to initialize your JL Cooper fader controllers.
Fader controller connections are shown for both the MCS-3000X and the FaderMaster Pro (see “JL Cooper MCS-3000X Fader Controller Cabling” on page 28 and “JL Cooper FaderMaster Pro Fader Controller Cabling” on page 28). There are two major differences between the two fader controllers:
• The MCS-3000X has a four-position switchpack that is not on the FaderMaster Pro.
• The MIDI IN and MIDI OUT are in opposite positions in the MCS-3000X and the FaderMaster Pro.
To connect the fader controllers:
1. Quit any open applications.
2. Shut down the Avid editing system.
3. Make sure your USB-to-MIDI converter is connected to the USB port as explained in “Connecting the USB-to-MIDI Converter” on page 26.
4. If you are cabling the MCS-3000X, set switch 4 to the ON (down) position. The switch is upside down on the MCS-3000X (see the following figure).
5. Locate two MIDI cables with 5-pin DIN connectors.
n You can use In B and Out B on the rear of the USB-to-MIDI converter instead of In A and Out A, but you need to reconfigure the ports using the software explained in your Avid editing application ReadMe file.
6. Plug one end of the first MIDI cable into the In A connector of the USB-to-MIDI converter (see “USB-to-MIDI Converter Front Panel” on page 28), and the other end of the cable into the MIDI OUT connector of the fader controller.
7. Plug one end of the second MIDI cable into the Out A connector of the USB-to-MIDI converter, and the other end of the cable into the MIDI IN connector of the fader controller.
Using the Avid Mojo DNA
28
8. Make sure the button on the front of the USB-to-MIDI converter is pushed in (see “USB-to-MIDI Converter Front Panel” on page 28).
JL Cooper MCS-3000X Fader Controller Cabling
JL Cooper FaderMaster Pro Fader Controller Cabling
USB-to-MIDI Converter Front Panel
MIDI OUT MIDI INSELECT
POWER
ONEXPANDER
1234
CTS 206-4
ON
In B Out BOut A
USB-to-MIDI converter (rear)
MIDI cable
Switch
MIDI OUT
MIDI IN
MIDI cable to In A (see “USB-to-MIDI Converter Front Panel” on page 28)
Out A
Power 9VDC MIDI In MIDI Out Switch In Switch Out
+_
In B Out BOut A
USB-to-MIDI converter (rear)
MIDI cable
Out AMIDI OUT
MIDI IN
MIDI cable to In A (see “USB-to-MIDI Converter Front Panel” on page 28)
IN A
IN A IN B
OUT A OUT B
USB/MIDIThru
USB
Button (In position)
In A
Connecting Serial and MIDI Port Devices
29
Connecting the Yamaha 01V Mixer
To connect the 01V mixer:
1. Quit any open applications.
2. Shut down the Avid editing system.
3. Make sure your USB-to-MIDI converter is connected to the USB port as explained in “Connecting the USB-to-MIDI Converter” on page 26.
4. Locate two MIDI cables with 5-pin DIN connectors.
n You can use In B and Out B on the rear of the USB-to-MIDI converter instead of In A and Out A, but you need to reconfigure the ports using the software explained in your Avid editing application ReadMe file.
5. Plug one end of the first MIDI cable into the In A connector of the USB-to-MIDI converter (see “USB-to-MIDI Converter Front Panel” on page 28).
6. Plug the other end of the cable into the MIDI OUT connector of the 01V mixer (see the following figure).
7. Plug one end of the second MIDI cable into the Out A connector of the USB-to-MIDI converter.
8. Plug the other end of the cable into the MIDI IN connector of the 01V mixer (see the following figure).
9. Make sure button on the front of the USB-to-MIDI converter is pushed in (see “USB-to-MIDI Converter Front Panel” on page 28).
Yamaha 01V Mixer Rear View
n You must set up the 01V mixer using its front panel. See your Avid editing application Help for more setup instructions.
MONITOR OUTSREREO OUT
DIGITAL STEREOOMNI OUTCOAXIAL
MIDI TO HOST
ININOUT OUTTHRU
R L
R L
4 3 2 1
POWEROPTION 1/0
ON OFF
In B Out BOut A
USB-to-MIDI converter (rear)
Out A
MIDI OUT MIDI IN
MIDI cable to In A (see “USB-to-MIDI Converter Front Panel” on page 28)
Using the Avid Mojo DNA
30
Controlling a Video Deck
Avid editing systems provide video deck control through a serial control connector on most analog decks. You can control a single deck by using an RS-232 to RS-422 serial adapter. An optional RS-232 to RS-422 serial adapter kit is available through Avid.
The optional serial adapter kit that contains the following:
• An RS-232 to RS-422 serial adapter
• Two serial cables with 9-pin male connectors at both ends
To connect a single deck to your system:
1. Locate the serial adapter kit.
2. Attach one end of a 9-pin cable to the end of the serial adapter labeled RS-232.
3. Attach the other end of the 9-pin cable to the serial port on the Avid editing system (see the following figure) or to the serial connector of the USB-to-serial adapter.
n When you attach the cable to the serial port on the PC, note if you are using the COM1 or COM2 serial port. You need to select the same port in the Avid editing application.
Video Deck Control Cabling
4. Attach one end of another 9-pin cable to the end of the serial adapter labeled RS-422.
5. Attach the other end of the 9-pin cable to the remote serial port of the video deck.
n Place the deck in Remote mode before attempting to control the deck using the software. See the documentation provided with your deck.
To video deck
RS-422 connection RS-232 connection
To Avid editing system
Serial Adapter
Storage
31
Storage
Storage options are explained in the following sections.
SCSI Support
Avid has qualified the two SCSI channels on the rear of the xw8000 system (see “HP xw8000 System Slot Configuration and Connections” on page 19). The channels connect to a dual U320 chip on the system board. You can use the two SCSI connectors at the rear of the system and a Fibre Channel board in the xw8000 system at the same time.
Avid supports the ATTO SCSI UL3D/160 LVD board in the G4 system and the G5 system. Additional boards might be supported at a later date. You can use a SCSI board and a Fibre Channel board at the same time in the G4 system or the G5 system.
Documentation for connecting storage devices is included with the devices on a CD-ROM if they are purchased from Avid. Striping information can be found on the Avid Knowledge Center.
n Contact your Avid Sales and Product information line at 800-949-2843 for the latest storage product information.
1394 Support
When you are using an Avid Mojo DNA and you want to use 1394 (FireWire) drives, you need a second 1394 OHCI board on a different bus segment in your Avid editing system. See your computer manufacturer’s documentation to identify a PCI bus slot that is on a different bus segment than the 1394 port used for the Avid Mojo DNA.
n If you use a 1394 board in slots 3, 4, or 5 (PCI-X slots) in the xw8000 it must be a “universal” PCI card and not a +5V-only board.
See www.avid.com/Products for your specific application to determine the supported 1394 boards.
Using the Avid Mojo DNA
32
n At this time, Avid has not qualified a FireWire 800 (or 1394b) drive to be used with Avid Mojo DNA systems. For the latest qualified storage products, contact your local Avid Reseller or call the Avid Sales and Product information line at 800-949-2843 for the latest information about available drives.
Internal IDE Drives
An internal IDE drive can be used for media storage with your Avid Mojo DNA.
Ethernet Support
At this time only the Alacritech® 1-Gb board is supported. See specifications at www.avid.com/Products/Avid_application for supported devices and configurations.
n You cannot use the built-in 1394 connection and the built-in 1-Gb Ethernet for a Avid LANshare EX connection in the xw8000 system at the same time.
Fibre Channel Support
Avid provides support for local storage using the following Fibre Channel boards in the xw8000 system, G4 system, and G5 system:
• ATTO 2-Gb optical Fibre Channel (Model 3300, single channel)
• ATTO 2-Gb copper Fibre Channel (Model 3305, single channel)
Avid has also qualified the NewsCutter XP as a Fibre Channel client on an Avid Unity MediaNetwork.
Storage
33
Formatting and Striping MediaDrives (Windows)
To use all the resolutions available in your Avid editing application, you might need to stripe your MediaDrives. Disk drives must be configured as Dynamic if you are striping drives.
To configure and stripe a drive:
1. Start your system, and log into an account with administrative privileges.
2. Right-click the My Computer icon, and select Manage.
The Computer Management window opens.
3. Click the Disk Management folder.
n For more information on the Computer Management window, click the Help icon in the toolbar of the Computer Management window.
4. Make a drive Dynamic by right-clicking the disk ID section of the disk in the Computer Management window and selecting Upgrade to Dynamic disk, or Create Dynamic disk, depending upon the status of your disk.
When you select a disk in the Computer Management window, the white section of the disk changes to stripes, showing that the section has been selected.
5. Repeat step 4 for each drive you want to stripe.
6. Right-click one of the Dynamic drives and select Action > Create Volume.
7. Follow the instructions in the Create Volume Wizard to finish striping the drives using NTFS format.
Using the Avid Mojo DNA
34
Formatting and Striping MediaDrives (Macintosh)
To use all the resolutions available in your Avid editing system, use the ATTO ExpressStripe software to stripe drives on the Mac OS® X operating system. The ExpressStripe software is installed in the following location:
/Applications/ExpressStripe
The instructions for using the software are in a PDF file, Expressstripe.pdf, that is installed along with the ExpressStripe application.
n You must be logged in as an Administrator to stripe drives.
c Do not use the Apple Disk Utility application (in Applications/Utilities) to stripe drives. If you use the Disk Utility application, you cannot view the drives on the Mac OS 9 system. Additionally, Avid’s drive filtering feature does not function properly, resulting in poor performance.
Using Striped Drives on Mac OS X and Mac OS 9.x Systems
The Avid editing software automatically recognizes drives that were striped on Mac OS 9.x. You should be able to use these drives to edit and play video. However, if you move a drive that was striped on a Mac OS X system back to Mac OS 9.x, you cannot play video from the drives on Mac OS 9.x. If necessary, you can set up your Mac OS 9.x system so that it recognizes the drives. You can then copy media files from the drive to your Mac OS 9.x drives.
To set up a Mac OS 9.x system to recognize drives that were striped on a Mac OS X system:
1. Navigate to the following folder:
Applications/Avid Goodies/OS 9/System Folder/Extensions
2. Copy the file ~~ExpressStripe_OS9_Enablr to the Extensions folder on your Mac OS 9 system.
3. Restart the Mac OS 9 system.
Storage
35
The system is now able to recognize the striped drives. You can use the drives to copy media onto your Mac OS 9 drives.
c Do not run a Mac OS 9 Avid editing application on the same system as a Mac OS X Avid editing system. There might be conflicts between the system files used by the two applications.
Moving Striped Drives to Another System (Macintosh Only)
In order to move striped drives to another system, you need to be able to identify the drives that make up a particular striped set. This was easy on Mac OS 9 because the system allowed you to use the SCSI ID order when striping drives.
On Mac OS X, the system does not use the SCSI ID but instead uses its internal diskn name (where n is the drive number) when creating the striped sets. You can use Avid Storage Manager or ExpressStripe to identify a striped set on Mac OS X.
To use Avid Storage Manager to identify a striped set:
1. Start the Avid Storage Manager application and select View > Volumes.
2. Select the striped volume you want to move and click Identify.
The system blinks the lights on the front of the drives that make up the volume.
To use ExpressStripe to identify a striped set:
1. Start the ExpressStripe application.
2. In the opening dialog boxes, select Utilities and then select Benchmark.
3. Select the striped volume you want to move and click Start.
The system runs the benchmark test on the volume and shows activity on the front of the drives that make up the volume.
Using the Avid Mojo DNA
36
Specifications
The following sections provide specifications for the Avid Mojo DNA.
Dimensions and Weight
The following table shows the dimensions and weight for the Avid Mojo DNA enclosure. The dimensions are based on the unit in the stand; the orientation is shown in “Avid Mojo DNA in the Stand” on page 5.
Environmental Specifications
The following table shows the environmental specifications for the Avid Mojo DNA enclosure.
Dimensions and Weight
Dimension Avid Mojo DNA Stand
Width 1.13 in (28.7 mm) 4.5 in (114.3 mm)
Height 11.0 in (279.4 mm) 2.13 in (54.1 mm)
Depth 6.8 in (172.7 mm) 8.5 in (215.9 mm)
Weight 1.5 lb (0.68 kg) 1.32 lb (0.59 kg)
Environmental Specifications
Environment Specification
Ambient room temperature (Maximum) 95°F (35°C)
Operating humidity 5% to 90% noncondensing
Storage temperature –40°F to 158°F (–40°C to 70°C)
Storage humidity 5% to 95% noncondensing
Specifications
37
Electrical Specifications
The following table shows electrical specifications for the power adapter used to power the Avid Mojo DNA enclosure.
Electrical Specifications for Power Adapter
Topic Specification
Voltage
Input range
Output
90 V ac to 264 V ac
9 V dc
Frequency range 47 Hz to 63 Hz
Current
ac input
dc output
0.7 a for 115 V ac0.4 a for 230 V ac
2.23 a
Watts 20 w
Using the Avid Mojo DNA
38
Regulatory and Safety Notices
The following sections explain the regulatory and safety notices for the Avid Mojo DNA.
Warnings and Cautions
w Never install equipment if it appears damaged.
w Disconnect the power cord before servicing unit.
w Only perform the services explicitly described in this document. For services or procedures not outlined in this document, speak with authorized Avid service personnel.
c Follow all warnings and cautions in the procedures.
c Operate the device within its marked electrical ratings and product usage instructions.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Regulatory and Safety Notices
39
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian ICES-003
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
European Union Notice
Declaration of Conformity (According to ISO/IEC Guide 22 and EN 45014)
Application of Council Directives:
73/23/EEC, 89/336/EEC.
Standards to which Conformity is Declared:
EN60950:2000 Third EditionCISPR 22:1997 / EN55022:1994 + A1:1995 + A2:1997 Class B EN55024:1998/EN61000 — 3-2, 4-2, 4-3, 4-4, 4-5, 4-6, 4-8, 4-11, 3-3
Manufacturer’s Name:
Avid Technology, Inc. 1925 Andover StreetTewksbury, MA 01876, USA
European Contact: Nearest Avid Sales and Service Office or Avid Technology International B.V. Sandyford Business Center Unit 3,Dublin 18, Ireland
Type of Equipment: Information Technology Equipment
Using the Avid Mojo DNA
40
Product Name: Products for the Windows NT, Windows 2000, or Windows XP Operating System: Avid Adrenaline DNA, Avid DS Nitris DNA, Avid Equinox Break-Out-Box, Avid|DS, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, NewsCutter, NewsCutter DV, NewsCutter XP, Pro Tools AVoption|V10, Symphony
Products for the Mac OS X Operating System: Avid Adrenaline DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, Pro Tools AVoption|V10, Symphony
Products for the UNIX Operating System: AirPlay, VideoSPACE
Products for MediaNetwork and Workgroups: Avid ProEncode, Avid Unity MediaManager, Avid Unity MediaNetwork, Avid Unity TransferManager, LANserver, LANserver EX, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Nearchive, PortServer, Xdeck
Base Model Numbers: None
Product Options: All
Year of Manufacture: 2004
Regulatory and Safety Notices
41
(1) Products for the Windows NT, Windows 2000, or Windows XP Operating System: products were tested in a typical Avid Adrenaline DNA, Avid DS Nitris DNA, Avid Equinox Break-Out-Box, Avid|DS, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, NewsCutter, NewsCutter DV, NewsCutter XP, Pro Tools AVoption|V10, or Symphony configuration.
(2) Products for the Mac OS X Operating System: products were tested in a typical Avid Adrenaline DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, Pro Tools AVoption|V10, or Symphony configuration.
(3) Products for the UNIX Operating System: products were tested in an AirPlay or VideoSPACE configuration.
(4) Products for MediaNetwork and Workgroups: products were tested in a typical Avid ProEncode, Avid Unity MediaManager, Avid Unity MediaNetwork, Avid Unity TransferManager, LANserver, LANserver EX, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Nearchive, PortServer, or Xdeck configuration.
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards.
George R. Smith, Director of Hardware Engineering
Australia and New Zealand EMC Regulations
John Kells, Australian Operations ManagerAvid Technology (Australia)Unit B5 Skyline PlaceFrench Forest NSW 2086AustraliaPhone: 61-2-8977-4800
N1709
Using the Avid Mojo DNA
42
Technical Support Information
Most products feature a number of coverage options. Avid Assurance service offerings are designed to facilitate your use of Avid solutions. Service options include extended telephone coverage, automatic software maintenance, extended hardware warranty, and preferred pricing on replacement parts.
For more information regarding Avid’s service offerings, visit www.avid.com/support or call Avid Sales at 800-949-AVID (800-949-2843).
Program availability and details might vary depending on geographic location and are subject to change without notice. Contact your local Avid office or your local Avid Reseller for complete program information and pricing. However, if you need help locating an Avid office or Avid Reseller near you, please visit www.avid.com or call in North America 800-949-AVID (800-949-2843). International users call 978-275-2480.
Copyright and DisclaimerProduct specifications are subject to change without notice and do not represent a commitment on the part of Avid Technology, Inc.
The software described in this document is furnished under a license agreement. You can obtain a copy of that license by visiting Avid's Web site at www.avid.com. The terms of that license are also available in the product in the same directory as the software. The software may not be reverse assembled and may be used or copied only in accordance with the terms of the license agreement. It is against the law to copy the software on any medium except as specifically allowed in the license agreement.
Avid products or portions thereof are protected by one or more of the following United States patents: 4,746,994; 4,970,663; 5,045,940; 5,267,351; 5,309,528; 5,355,450; 5,396,594; 5,440,348; 5,452,378; 5,467,288; 5,513,375; 5,528,310; 5,557,423; 5,568,275; 5,577,190; 5,583,496; 5,584,006; 5,627,765; 5,640,601; 5,644,364; 5,654,737; 5,715,018; 5,719,570; 5,724,605; 5,726,717; 5,729,673; 5,745,637; 5,752,029; 5,754,851; 5,799,150; 5,812,216; 5,828,678; 5,842,014; 5,852,435; 5,905,841; 5,929,836; 5,930,445; 5,946,445; 5,987,501; 5,999,406; 6,016,152; 6,018,337; 6,023,531; 6,038,573; 6,058,236; 6,061,758; 6,091,778; 6,105,083; 6,118,444; 6,128,001; 6,134,607; 6,137,919; 6,141,007; 6,141,691; 6,198,477; 6,201,531; 6,211,869; 6,223,211; 6,249,280; 6,269,195; 6,317,158; 6,317,515; 6,330,369; 6,351,557; 6,353,862; 6,357,047; 6,392,710; 6,404,435; 6,407,775; 6,417,891; 6,426,778; 6,477,271; 6,489,969; 6,512,522; 6,532,043; 6,546,190; 6,552,731; 6,553,142; 6,570,624; 6,571,255; 6,583,824; 6,596,031; 6,618,547; 6,636,869; D352,278; D372,478; D373,778; D392,267; D392,268; D392,269; D395,291; D396,853; D398,912. Other patents are pending.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Avid Technology, Inc.
Copyright © 2004 Avid Technology, Inc. and its licensors. All rights reserved.
Technical Support Information
43
Attn. Government User(s). Restricted Rights LegendU.S. GOVERNMENT RESTRICTED RIGHTS. This Software and its documentation are “commercial computer software” or “commercial computer software documentation.” In the event that such Software or documentation is acquired by or on behalf of a unit or agency of the U.S. Government, all rights with respect to this Software and documentation are subject to the terms of the License Agreement, pursuant to FAR §12.212(a) and/or DFARS §227.7202-1(a), as applicable.
Trademarks888 I/O, Adrenaline, AirPlay, AirSPACE, AirSPACE HD, AniMatte, AudioSuite, AudioVision, AutoSync, Avid, Avid DNA, AVIDdrive, AVIDdrive Towers, Avid Mojo, AvidNet, AvidNetwork, AVIDstripe, Avid Unity, Avid Xpress, AVoption, AVX, CamCutter, ChromaCurve, ChromaWheel, DAE, D-Fi, D-fx, Digidesign, Digidesign Audio Engine, Digidesign Intelligent Noise Reduction, DigiDrive, Digital Nonlinear Accelerator, DigiTranslator, DINR, D-Verb, Equinox, ExpertRender, FieldPak, Film Composer, FilmScribe, FluidMotion, HIIP, HyperSPACE, HyperSPACE HDCAM, IllusionFX, Image Independence, Intraframe, iS9, iS18, iS23, iS36, Lo-Fi, Magic Mask, make manage move | media, Marquee, Matador, Maxim, MCXpress, Media Composer, MediaDock, MediaDock Shuttle, Media Fusion, Media Illusion, MediaLog, Media Reader, Media Recorder, MEDIArray, MediaShare, Meridien, MetaSync, NaturalMatch, Nearchive, NetReview, NewsCutter, Nitris, OMF, OMF Interchange, OMM, Open Media Framework, Open Media Management, ProEncode, Pro Tools, QuietDrive, Recti-Fi, RetroLoop, rS9, rS18, Sci-Fi, Softimage, Sound Designer II, SPACE, SPACEShift, Symphony, the Avid|DS logo, Trilligent, UnityRAID, Vari-Fi, Video Slave Driver, VideoSPACE, and Xdeck are either registered trademarks or trademarks of Avid Technology, Inc. in the United States and/or other countries.
iNEWS, iNEWS ControlAir, and Media Browse are trademarks of iNews, LLC.
Alacritech is a registered trademark of Alacritech, Inc. Apple, PowerBook, FireWire, Macintosh, and Mac OS are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. ATTO is a trademark of ATTO Technology, Inc. FaderMaster Pro is a trademark of JL Cooper, a division of Sound Technology. GeForce, NVIDIA, and Quadro are registered trademarks or trademarks of NVIDIA Corporation in the United States and/or other countries. HP is a registered trademark of Hewlett-Packard Company. PowerPC is a registered trademark of International Business Machines Corporation, used under license therefrom. MIDISPORT is a trademark of M-AUDIO. RCA is a registered trademark of General Electric Company. VLXi is a registered trademark of Videomedia, Inc. Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. Yamaha is a registered trademark of Yamaha Corporation of America. All other trademarks contained herein are the property of their respective owners.
Using the Avid Mojo DNA • Part 0130-06063-01 Rev. A • April 2004