understanding tack vs. cure...los adhesivos basados en solvente no permite esto. es importante otra...
TRANSCRIPT
Understanding Tack vs. Cure
When looking at the bond strength of adhesives, it is important to differentiate the strength of the
bond when the substrates are initially bonded from the strength of the bond after the adhesive has
cured. This document is designed to address the initial bond strength. As we compare the initial
bond strength of SIMALFA vs. a solvent based adhesive, it is important to understand tack vs. cure.
SIMALFA will tack instantly, while a solvent based adhesive will cure instantly. We fi nd that the
instant tack offered by SIMALFA allows for much more versatility and speed in your production and
processes when compared to the instant cure of a solvent based adhesive.
The best way to demonstrate the difference is to look at the simple tack tests illustrated on page 2
of this document: shear strength, pull strength, and peel strength.
Shear Strength
When we refer to shear strength, we refer to the strength of the adhesive bond while attempting to
slide 2 parallel bonded substrates past each other. Both SIMALFA and solvent based adhesives offer
instant shear strength.
Pull Strength
Pull strength refers to the strength of the bond when pulling the substrates in a direction that is
perpendicular to the bonded surface. Both SIMALFA and solvent based adhesives offer instant
pull strength.
Peel Strength
Peel strength is determined by the ability of the adhesive to resist separation when a substrate is
peeled up from the edge to remove it from the material to which it has been bonded. This is where
we fi nd the key difference between SIMALFA and solvent based adhesives. SIMALFA is designed to
allow the substrates to be peeled and repositioned while the adhesive is still wet. This will allow the
operators to correctly position and reposition the substrates without damaging them, or having to
apply more adhesive. This provides numerous advantages that can help with speed, process, and
overall quality. Solvent based adhesives do not allow for this. It is again important to note that once
SIMALFA has cured, peeling will result in destruction of the substrates.
La comprensión de Fijar vs. Curar
Al mirando la resistencia de la adherencia de los adhesivos, es importante que distingue la resistencia de
la adherencia cuando los sustratos se adhieren inicialmente de la resistencia de la adherencia después de
el adhesivo ha curado. Este documento está diseñado para tratar la resistencia inicial de la adherencia.
Mientras comparamos la resistencia inicial de la adherencia de Simalfa vs. otro adhesivo basado en
solvente, la comprensión de fi jar vs. curar es importante. Simalfa fi jará inmediatamente, pero un
adhesivo basado en solvente curará inmediatamente. Encontramos que la fi jación inmediatamente que
SIMALFA ofrece permite más versatilidad y velocidad en su fabricación y sus procesos comparado con la
curación inmediatamente del adhesivo basado en solvente.
La manera mejor para demonstrar la diferencia es mirar a las pruebas simples de la fi jación que están
ilustrados en página 2 de este documento: La resistencia a cortar, la resistencia a tirar, y la resistencia a
pelar.
La resistencia a cortar
La resistencia a cortar se refi era a la resistencia de la adherencia del adhesivo cuando trata de mover los
dos sustratos paralelos que están adheridos en dirección contraria uno al otro. Ambos productos, SIMALFA
y los adhesivos basados en solvente, ofrecen la resistencia inmediatamente a cortar.
La resistencia a tirar
La resistencia a tirar se refi era a la resistencia de la adherencia cuando tira los sustratos en una dirección
que es perpendicular a la superfi cie adherida. Ambos productos, SIMALFA y los adhesivos basados en
solvente, ofrecen la resistencia inmediatamente a tirar.
La resistencia a pelar
La habilidad del adhesivo resistir la separación cuando un sustrato está pelado del borde para sacarlo
de la materia a que ha sido adherido determina la resistencia a pelar. Aquí encontramos la diferencia
esencial entre SIMALFA y los adhesivos basados en solvente. SIMALFA es diseñado para permitir el pelar
y el recolocar de los sustratos cuando el adhesivo todavía está limpia. Este permite que los operadores
puedan colocar correctamente y recolocar los sustratos sin dañarlos o sin la necesidad de aplicar más
adhesivo. Este proporciona muchas ventajas que pueden ayudar con la velocidad, el proceso, y la
cualidad total. Los adhesivos basados en solvente no permite esto. Es importante otra vez para apuntar
que cuando SIMALFA ha curado, el pelar resultará en la destrucción de los sustratos.