(uk) limited curtain fire dampers

CURTAIN FIREDAMPERS

Quality Assurance systemassessed to BS EN ISO 9002

4 hour fire resistance

0100 Series available up to 1.5m x 1.5m in a single module

Infinite sizing capability, withinstated minimum and maximumdimensions

3 alternative casing depths

Standard construction ofgalvanised steel; options withstainless steel blades or stainlesssteel blades and frame

Factory fitted HEVAC/HVCAapproved installation frames

Comprehensive control options

Dry wall frame available

F e a t u r e s

Advanced Air(UK) Limited

A p p r o v a l s

Fire tested to BS 476 Part 8 - FROSI No 6110

Dynamic fire test to Draft ISO 10294/1 LPC TE 81844(0100 Series, to max. test size of 1000 x 1000mm)

LPCB Certificate of Product Conformity - 4 hourresistance integrity

Loss Prevention Council ‘Approved Product’

Accepted by the Department of Architecture and CivicDesign of the Greater London Council

Conformance to DW 142 as appropriate

Lloyds Register of Shipping Certificate No. SVG/F93/094

Underwriters Laboratories Inc. USA

Underwriters Laboratories of Canada

Shock tested to DEF Standard 07-55

Leakage tested by BSRIA - Report No. 3870 Nos. 1&2

Europe, Far East and New Zealand (FRC) Approvals

0100 & 0200 SERIES

Advanced Air fire dampers are manufactured in accordance with a Quality Assurance system

assessed to BS EN ISO 9002. The company is registered to this standard with BSI (Certificate

No. FM 1714) and with the Loss Prevention Certification Board (Certificate No. 128).

The Curtain Fire Dampers have the LPCB Certificate of Product Conformity (No. 128a), and are on the Loss Prevention Council

list of Approved Products.

QUALITYASSURANCE

The Advanced Air range of curtain fire dampers is designed to stop the spread of fire through

ducts, walls and floors. The range incorporates features required by specifiers, contractors and fire authorities,

and embodies the combined experience of Nailor Industries Inc. (Canada and United States of America) and

Advanced Air (UK) Limited, in design, manufacture, sales and service of fire dampers.

PAGE 2Advanced Air

The full range successfully completed 4 hour fire tests to BS 476 Part 8 (FROSI Report No. 6110).

Additionally, the 0100 Series has been successfully tested under dynamic conditions to the draft ISO/DIS 10294/1 Standard

(LPC TE 81844). Throughout the course of the 4 hour test, a pressure differential of 300 Pa was maintained across the closed

damper. Leakage through the closed curtain blades was measured, and the dampers achieved an E240 classification.

FIRE TESTS

INTRODUCTION & INDEX

PRODUCT SELECTION GUIDE

STANDARD MODEL - DIMENSIONS & FEATURES

THINWALL MODEL - DIMENSIONS & FEATURES

DEEP-CASE MODEL - DIMENSIONS & FEATURES

HEVAC/HVCA INSTALLATION FRAME

MULTIPLE SECTIONS

FUSIBLE ELEMENTS

SECONDARY ELECTRICAL ACTUATORS

BLADE POSITION INDICATORS

WEIGHT CHART

PRODUCT CODING

PAGE 22

PAGE 33

PAGE 44 && 55

PAGE 66 && 77

PAGE 88 && 99

PAGE 1100

PAGE 1111

PAGE 1122

PAGE 1133

PAGE 1144

PAGE 1155

PAGE 1166

INDEX0100 & 0200 Series

INTRODUCTION

Advanced Air

FOR FURTHER TECHNICAL

INFORMATION, SEE PAGES

4 & 5

MAXIMUM SINGLE

SECTION DUCT

SIZE (W X H)

CASE DEPTH 80MM STANDARD MODEL BLADE WIDTH 66MM

Model CodeSLEEVE/WALL MOUNT

LOW VELOCITY

SPIGOT MOUNT MEDIUM

VELOCITY

SPIGOT MOUNT (ALSO

FLAT OVAL) HIGH

VELOCITY

1525 x 1525

0140 0150 0160

1475 x 1475 1475 x 1325

PRODUCT SELECTION GUIDE

All models are, as standard, manufactured from galvanised steel. Options include stainless steel blades, or stainlesssteel blades and casings (Grade 430).For full Product Coding details, see back page.For full details of Multiple Section arrangements, see Page 11.

APPLICATION

GUIDE



6 & 7

MAXIMUM SINGLE

SECTION DUCT

SIZE (W X H)

CASE DEPTH 55MM THINWALL MODEL BLADE WIDTH 40MM


LOW VELOCITY

SPIGOT MOUNT MEDIUM

VELOCITY

SPIGOT MOUNT (ALSO

FLAT OVAL) HIGH

VELOCITY

1000 x 1000

0240 0250 0260

950 x 950 950 x 775

APPLICATION

GUIDE



8 & 9

MAXIMUM SINGLE

SECTION DUCT

SIZE (W X H)

CASE DEPTH 108MM DEEP-CASE MODEL BLADE WIDTH 66MM


LOW VELOCITY

TOP FLANGE MOUNT

HIGH VELOCITY

SPIGOT MOUNT (ALSO

FLAT OVAL) HIGH

VELOCITY

1525 x 1525

0110 0120 0130

1525 x 1350 1475 x 1325

APPLICATION

GUIDE

DUCT WIDTH + 50 mm80

DUCT WIDTH - 4 mm

DU

CT

HE

IGH

T -

4 m

m

DU

CT

HE

IGH

T +

50

mm

5 050

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T +

11

0 m

m

57

57

9 0

DUCT WIDTH + 60 mm

DU

CT

HE

IGH

T +

60

mm

9 0

DUCT WIDTH + 50 mm80DUCT WIDTH - 4 mm

DU

CT

HE

IGH

T -

4 m

m

'A'

27

5 050

DUCT WIDTH + 110 mmD

UC

T H

EIG

HT

- 4

mm

57

'B'

9 0

DUCT D IA . + 50 mm80

DU

CT

DIA

. -

4 m

m 'C'

27

5 050DUCT D IA + 110mm

DU

CT

DIA

- 4

mm

57

'D'

9 0

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T -

4m

m

57

'F'

9 0

STANDARD MODEL DIMENS IONAL DATA

Advanced Air


DU

CT

HE

IGH

T -

4 m

m 'E'

27

5 050

DUCT WIDTH - 3 mm80

DU

CT

HE

IGH

T -

3 m

m

100 - 300

301 - 525

526 - 700

701 - 925

926 - 1150

1151 - 1325

52 82

77 107

102 132

127 157

152 182

177 207

“A” “B”DUCT HEIGHT

100 - 300

301 - 525

526 - 700

701 - 925

926 - 1000

52 82

77 107

102 132

127 157

152 182

“E” “F”DUCT HEIGHT

100 - 300

301 - 525

526 - 700

701 - 925

926 - 1000

52 82

77 107

102 132

127 157

152 182

“C” “D”DUCT HEIGHT

For full details of Product Coding, see back page

All dimensions in mm

(1000 - 1325 see 0130 Series)

(1000 - 1325 see 0130 Series)

MODELS WITH HEVAC/HVCA INSTALLATION FRAMESBASE MODELS

0140-00 0150-10 0160-10 0160-20 0160-30

0140-00 0140-01

0150-10 0150-11

0160-10 0160-11

0160-20 0160-21

0160-30 0160-31

STANDARD MODEL PRODUCT FEATURES

PAGE 5Advanced Air

Casings: are manufactured from 1.2mm galvanised

mild steel. For 0160-20 Models over 1 metre in

diameter, the casing is manufactured from 1.6mm

galvanised mild steel.

Blades: are specially rollformed from 0.8mm

galvanised mild steel as standard. “Horizontally” and

where specified “Vertically” mounted units, are

complemented with two stainless steel coil type

constant tension springs.

Fusible Link: unless specified otherwise will be

supplied rated at 72oC nominal. (See page 12 for

options).

The 100% galvanised mild steel constructed models

have been successfully corrosion tested by the G.L.C.

Scientific Branch in the U.K. and by U.L. Lab’s in the

U.S.A. to standard U.L. 555. Both tests involve long-

term exposure to highly concentrated salt laden air,

with consequent heavy deposition of materials.

Subsequently, the test units were immediately fired

and operated successfully.

Applicable to 0140 and 0150 Series recommended for Low and Medium velocities

Applicable to 0160 Series recommended for High velocities

PRODUCT SPECIFICATION

CASINGSManufactured from corrosion resistantgalvanised steel as standard.(Grade 430 stainless steel optional).

PULL RINGSTo enable resetting of the damper fromthe non-access side. (Specific sizesonly).

BLADE GUIDE/LOCKING RAMPSGalvanised steel locking ramps ensurepositive blade closure within integralblade guides.

FUSIBLE LINK/RELEASE MECHANISMTypical two-piece fusible link rated at72oC.Alternative temperature rated fusiblelink mechanisms available. (See page 12).

BLADESRollformed single skin interlockinggalvanised high integrity curtain shutter.(Grade 430 stainless steel bladesoptional).

SPRINGSStainless Steel coil tension springsensuring powerful blade closure whenappropriate.

CORROSION TEST

PERFORMANCE DATA

The illustration shows model 0140

00

0.0512.5

0.10 25

0.1537.5

0.2 50

0.2562.5

0.3 INS W.G.75 PASCAL

2.5490

5980

7.51470

101960

12.5m/s2450ft/min

(55% - 78% Free Area)

Duct Velocities

55% Minimum FreeArea

(200 x 200))

78% Maximum Free Area (1000 x 1000

Pres

sure

Dro

p

00

0.1025

0.2 50

0.375

0.4 100

0.5125


5980

101960

152940

203920

25m/s4900ft/min

(100% Free Area)

Duct Velocities

(200 x 200))

(1000 x 1000)

Pres

sure

Dro

p


DU

CT

HE

IGH

T +

50

mm

DU

CT

HE

IGH

T -

4m

m

5 050

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T +

11

0 m

m

57

57

6 5

DUCT WIDTH + 60 mm

DU

CT

HE

IGH

T +

60

mm

6 5


DU

CT

HE

IGH

T -

4 m

m 'A'

27

5 050

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T -

4 m

m

57

'B'

6 5

DUCT D IA . + 50 mm55

DU

CT

DIA

. -

4 m

m 'C'

27

5 050

DUCT D IA + 110mm

DU

CT

DIA

- 4

mm

57

'D'

6 5

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T -

4M

M

57

'F'

6 5

THINWALL MODEL DIMENS IONAL DATA

Advanced Air

DUCT WIDTH - 4 mm

DU

CT

HE

IGH

T -

4 m

m

DUCT WIDTH + 50 mm5550

'E'

27

5 0

DUCT WIDTH - 3 mm55

DU

CT

HE

IGH

T -

3 m

m

100 - 150151 - 275276 - 375376 - 500501 - 625626 - 725726 - 775

5277102127152177202

82107132157182207232

“A” “B”DUCT HEIGHT

100 - 150151 - 275276 - 375376 - 500501 - 625626 - 725726 - 775

5277102127152177202

82107132157182207232

“C” “D”DUCT HEIGHT

100 - 150151 - 275276 - 375376 - 500501 - 625626 - 725726 - 775

5277102127152177202

82107132157182207232

“E” “F”DUCT HEIGHT



MODELS WITH HEVAC/HVCA INSTALLATION FRAMESBASE MODELS

0240-00 0250-10 0260-10 0260-20 0260-30

0240-00 0240-01

0250-10 0250-11

0260-10 0260-11

0260-20 0260-21

0260-30 0260-31

TH INWALL MODEL PRODUCT FEATURES

PAGE 7Advanced Air

Casings: are manufactured from 1.2mm galvanised

mild steel.







supplied rated at 72oC nominal.

(See page 12 for options).
















CORROSION TEST




PERFORMANCE DATA

00

0.0512.5

0.10 25

0.1537.5

0.2 50

0.2562.5


2.5490

5980

7.51470

101960

12.5m/s2450ft/min

(55% - 78% Free Area)

Duct Velocities


(200 x 200))


Pres

sure

Dro

p

00

0.1025

0.2 50

0.375

0.4 100

0.5125


5980

101960

152940

203920

25m/s4900ft/min

(100% Free Area)

Duct Velocities

(200 x 200))

(1000 x 1000)

Pres

sure

Dro

p

DUCT WIDTH - 6mm108 5050

DU

CT

HE

IGH

T -

4m

m

27

'A'

DUCT WIDTH - 4mmDUCT WIDTH + 50mm

108

DU

CT

HE

IGH

T -

4m

m

27

'B'

DUCT WIDTH + 110mm

DU

CT

HE

IGH

T -

4m

m

57

'C'

1 22

108 DUCT D IA . + 50mm

DU

CT

DIA

. -

4m

m

'D'5 0 50

27

DUCT D IA+ 110mm

DU

CT

DIA

- 4

mm

57

'E'

1 22

DUCT WIDTH + 110 mm

DU

CT

HE

IGH

T -

4m

m

57

'G'

1 22

DEEP CASE MODEL DIMENS IONAL DATA

Advanced Air


DU

CT

HE

IGH

T -

4 m

m 'F'

27

5 050

DUCT WIDTH - 6mm108

DU

CT

HE

IGH

T -

6m

m


1001 - 11501151 - 1325

152177

182207

“F” “G”DUCT HEIGHT

1001 - 11501151 - 1325

152177

182207

“D” “E”DUCT HEIGHT

100 - 300301 - 525526 - 700701 - 925926 - 11501151 - 1325

5277102127152177

82107132157182207

“B” “C”DUCT HEIGHT

100 - 300301 - 525526 - 700701 - 925926 - 11501151 - 1350

5277102127152177

“A”DUCT HEIGHT


MODELS WITH HEVAC/HVCA INSTALLATION FRAMES

NOT AVAILABLE FOR THIS MODEL

NOT AVAILABLE FOR THIS MODEL

BASE MODELS

0110-00 0120-00 0130-00 0130-20 0130-30

0110-00

0120-00

0130-00 0130-01

0130-20 0130-21

0130-30 0130-31

DEEP -CASE MODEL PRODUCT FEATURES

PAGE 9Advanced Air

Casings: the 0110 and 0120 Models have casings

manufactured from 0.8mm galvanised mild steel,

whilst the 0130 Model outer case is manufactured

from 1.2mm galvanised mild steel (1.6mm galvanised

mild steel is used for 0130-20 Models over 1m in

diameter)







supplied rated at 72oC nominal.

(See page 12 for options).
















CORROSION TEST




PERFORMANCE DATA

00

0.0512.5

0.10 25

0.1537.5

0.2 50

0.2562.5


2.5490

5980

7.51470

101960

12.5m/s2450ft/min

(55% - 78% Free Area)

Duct Velocities


(200 x 200))


Pres

sure

Dro

p

00

0.1025

0.2 50

0.375

0.4 100

0.5125


5980

101960

152940

203920

25m/s4900ft/min

(100% Free Area)

Duct Velocities

(200 x 200))

(1000 x 1000)

Pres

sure

Dro

p

HEVAC/HVCA I NSTAL LAT ION FRAME

ADDITIONAL NOTE

(CONFORMING TO SPECIFICATION NO HVC 6-5-83)

(a) in brickwork or blockwork walls and floors, the tabs shall be bent out and solidly built into mortar jointsbetween the brickwork or blockwork;(b) in the case of reinforced concrete walls and floors, the tabs shall be bent out and tied with wire to thereinforcing bars which will be deliberately left protruding into the opening and then the gap between theinstallation frame and the builders work backfilled with mortar or concrete on both sides of the flange(c) it is recommended that the fixing tabs are welded, bolted or wired back to supporting steelwork or anequivalent rigid structural member, to ensure that the installation strength is maximised.

Advanced Air (UK) Ltd recommend the above as the standard method for installation. However, the District Surveyor, Fire

Officer, and/or Specifying Authority as appropriate, may approve other methods of installation

Advanced Air

The installation frame is factory fitted to its respective fire damper and the assembly is delivered to site as one unit. Itobviates the need for sleeve and angle fitting and allows expansion of the fire damper in a fire condition within the frame, sothat the integrity of the fire wall or floor is not affected.

Flange with fixingtabs ensuresmaximum captivestrength whenfitted to builderswork.

Corner joints fittedwith all aluminium

rivets ensuresunimpeded

expansion offrame.

Corner mitresallow for frameexpansion. Firedamper is locatedcentrally by foldedcorner spacers.

The frame shall be installed centrally in the

th i cknes s o f a b r i ckwork o r conc re t e

surrounding wall or floor, or in the case of thick

walls or floors, so that the centre line of the

frame is at least 50mm away from the nearest

face of the wall or floor in which the assembly

is mounted.

Adjacent frame assemblies must be separated by

builders work of minimum thickness of 225mm

(between installation frame upstand flanges)

unless approval has been previously obtained

from the appropriate authority.

MAXIMUM DUCT DIMENSIONS: 2000 X 1475MM

MATERIAL: GALVANISED STEEL

225mm

50mm

��

��

��

��

Where multiple arrangements of Fire Dampers are

required to be fitted, the installer should submit his

proposed arrangement to the relevant local

authority or fire officer responsible for installation.

Closure strips of 1.2mm galvanised sheet steel in

“U” formed sections are supplied undrilled with all

Advanced Air Damper multiple assemblies of the

spigotted type, for positioning as shown to form

centre mullions 50mm x 50mm.

0110 & 0140

0120

0130 - 20

0130 - 30

0160 -10 & - 30

0160 - 20

3050 x 3050mm

3050 x 2875mm

2850mm dia.

3000 x 2850mm

3000 x 2850mm

1000mm dia.

Units are available up to:

Units are available up to:

MULT IP L E SECT IONS

��

�� Advanced Air Series 0100 and 0200 curtain

fire dampers have been successfully tested

and approved for use in 4 hour constructions.

When required by a District Surveyor, Fire

Officer, or specifying authority, two standard

fire dampers may be f i t ted back to back.

This arrangement is available for all square,

rectangular, round and oval spigotted models.

F i t t ing i s by inser t ing one sp igot wi th in

another, creating a male/female connection

(see i l lustrat ion). Where HEVAC/HVCA

installation frames are required, one such

frame must be fitted to each damper in the

assembly.

Advanced Air

MULTIPLE HORIZONTAL

ARRANGEMENT

DOUBLE UNITS

MULTIPLE VERTICALARRANGEMENT

0110 & 0140

0120

0130 - 20

0130 - 30

0160 -10 & - 30

0160 - 20

2590 x 1525mm

2590 x 1370mm

1350mm dia.

2550 x 1350mm

2550 x 1325mm

1000mm dia.

Please note that certain combinations of link, micro-switch, VPI, etc. may not be available on smaller units.

Please contact the Sales Office for full details.

This Flat-Bar Link is the standard link used, and

is held in position by removable chain links

Allows the Fire Damper to be tested quickly and

sa f e ly . The dampe r c an be mechan i ca l l y

released and reloaded with one hand on small

units from indicated side of the duct.

(The E.M.L. must be specifically ordered, as it is

an option).

A dual response fusible l ink which reacts

(melts) when subjected to either local heat or

an electrical impulse of low power and short

duration. The standard temperature rating is

74oC. The low power requirement of the

E.T.L. means that it can be released with an

e l ec t r i c a l impu l se (50 mi l l i s econds o f

between 6 volt and 30 volt AC or DC with a

minimum current of 0 .2 amperes) f rom a

suitable smoke detector or other source.

FLAT BAR LINK

EASY MAINTENANCE LINK - E.M.L.

ELECTRO-THERMAL LINK - E.T.L.

PAGE 12Advanced Air

FUS IBLE ELEMENTS

MINIMUM DAMPER SIZE

oC72o (Standard)

68o (Optional)

120o (Optional)

182o (Optional)

58o (Optional)

100o (Optional)

140o (Optional)

72 oC

72 oC

SECONDARY ELECTR ICAL ACTUATORS

PAGE 13Advanced Air

Please note that certain combinations of secondary electrical actuators, micro-switch, VPI, etc. may not be

available on smaller units. Please contact the Sales Office for full details.

Damper units are always supplied with overriding failsafe Fusible Links fitted

Electrically energised to activate closure ofthe curtain blade pack.

Norma l ly “de - ene rg i s ed” , a c t i va t ed by an

electrical impulse either from or via a detector or

control panel. The solenoid can be fitted for

standard “direct link” operation.

For maintenance/servicing the solenoid can be

manually over-ridden for testing purposes.

24 volt A.C., 110 volt A.C. and 240 volt A.C.

300 VA minimum required.

Interruption of electrical current to activateclosure of the curtain blade pack.

As an alternative to the solenoid for systems that

require normally “energised” actuators , that

au toma t i ca l l y ope ra t e i n t he even t o f an

interruption of electrical supply.

24 vo l t , 110 vo l t and 240 vo l t D .C. supp ly

models available, which when complemented

with a rectifier may be used with A.C. supply.

Magnets rated at 5w.

SOLENOID - A.C. VOLTAGE

ELECTRO-MAGNET

MINIMUM DAMPER SIZE

Max.25 mm

Max.100 mm

Max.25 mm

Max. 100 mm

Please note that certain combinations of blade position indicator, link, etc. may not be available on smaller units.

Please contact the Sales Office for full details.

To provide remote indication of whether the Blade Pack is open or closed.

The micro-switch can also be connected to any warning device controls circuit.

The electrical circuit is completed or broken when the lowest blade operates the arm of the micro-switch.

2 POLE - 1 NORMALLY CLOSED

+ 1 NORMALLY OPEN

SNAP ACTION

SUITABLE FOR UP TO 240V, 3A

To provide local indication of whether the blade pack is open or closed.

ELECTRICAL MICRO-SWITCH

VISUAL POSITION INDICATOR

PAGE 14Advanced Air

BLADE POS I T ION IND ICATORS

MINIMUM DAMPER SIZE

(PROVIDING REMOTE INDICATION)

(PROVIDING LOCAL INDICATION)

CURTAIN BLADE OPEN POSITION CURTAIN BLADE CLOSED POSITION

This indicator is normally fitted within the vertical face of the

case adjacent to the bottom blade when in the closed position

ADVANCED AIR - FIRE DAMPERS - NETT WEIGHTS

All weights are approximate and in Kilograms

WEIGHT CHART

PAGE 15Advanced Air

150 200 300 400 450 600 750 900 1050 1200 1500WIDTH (MM)

HEI

GH

T(M

M)

1

2

3

4

4

6

8

9

11

13

2003004506007509001050120013501500

2

2

3

4

5

6

8

9

11

13

2

3

4

6

6

7

9

10

12

14

3

4

4

7

8

8

10

12

14

16

3

4

5

7

8

8

10

12

14

16

5

5

7

8

9

10

12

13

16

17

6

7

7

9

10

11

12

14

17

19

6

7

8

10

11

12

14

15

17

20

8

9

10

12

12

14

16

18

20

24

9

10

12

13

14

15

18

23

26

30

10

12

15

17

19

21

25

28

31

36

GROUPSTRUCTURE

COMPANYDEVELOPMENT

ASSUREDQUALITY

CUSTOMERSERVICE

Advanced Air (UK) Limited is a member of the Nailor Industries International Group. The Group started operations in Toronto in 1971, founded by the current President and Chief

Executive Officer, Michael Nailor. Today there are factories in Toronto and Calgary in Canada, in Houston andFlorida in the USA, with Advanced Air (UK) Ltd. in Bury St Edmunds. The Group’s Research and DevelopmentLaboratory is located in Houston.

The Group manufactures a full range of dampers and air distribution products, including fire, smoke and controldampers, fire rated ceiling products, grilles, diffusers and VAV terminal units.

Formed in 1975, Advanced Air (UK) Ltd. relocated to Bury St Edmunds in 1980, where the company now occupies three manufacturing units.

These factories produce fire, smoke and control dampers for the UK and export markets. With agents anddistributors throughout Europe and the rest of the world, Advanced Air operates in a continually developinginternational market.

The company has always placed great emphasis on quality of production and design, and was among the first HVAC companies in the UK to be registered to BS 5750. Advanced Air’s

quality assurance system is now assessed to BS EN ISO 9002, through both BSI and the Loss PreventionCertification Board. The company’s fire and smoke dampers are included in the Loss Prevention Council’s list ofApproved Products.

Advanced Air has always been a customer led company, responding to the needs and demands of specifiers, designers and contractors. This has led to continuous improvement in

product design and in manufacturing technology. The company’s customer service function is seen as a key factorin Advanced Air’s success.

Ultimately, the customer requires the best possible products at competitive prices. Advanced Air meets thisdemand for value for money by focusing on simplicity in design, fitness for purpose, and high quality/low costproduction.

The company also keeps in touch with the wider issues affecting the HVAC industry, developing solutions to theproblems raised in such areas as lower energy usage, tighter fire safety regulations, indoor air quality, and therequirements of new European and worldwide standards.

1. The above nett weights are relevant to Models 0110 and 0140.2. For Models 0120 and 0150, a multiplier of 1.5 on the above weights should be used.3. For Models 0130 and 0160, a multiplier of 2 should be employed and where in addition an HEVAC/HVCA installationframe is included, an alternative multiplier of 3 should be utilised.4. Where Model 0200 Series are employed, a multiplier against the relevant pattern of 1.2 in addition should be used.

Advanced Air(UK) Limited

PO Box 153, Burrell Way, Thetford, Norfolk IP24 3WB, England Tel: 01842 753624 Fax: 01842 762032

The information contained in this publication is correct at the time of printing. Continuous product development means that from timeto time product specifications and other information will change. The company therefore reserves the right to modify or withdraw any

of the products described without prior notice

DES

IGN

EDA

ND

PRO

DU

CED

BY

TGL

TE

L: 0

1787

379

955

◆ SERIES 1000 - UNIVERSAL VOLUME CONTROL DAMPERS◆ SERIES 1200 - FIRE/SMOKE/CONTROL DAMPERS◆ SERIES 1400 - SLIMLINE BALANCE AND CONTROL DAMPERS◆ SERIES 2300 - LEAKAGE RATED FIRE/SMOKE DAMPERS◆ SERIES 2400 - INSULATED FIRE/SMOKE DAMPERS◆ SERIES 4000 - FIRE RATED DIFFUSER ASSEMBLIES◆ SERIES 0800 - ACCESS DOORS◆ SMOKE MANAGEMENT SYSTEMS

TYPICAL ORDER DETAIL

ASSOCIATED PRODUCTS

MOUNTING TYPE

0. BASE1. HEVAC/

HVCA FRAME

2. ONE MICRO SWITCH

3. HEVAC FRAME & MICRO SWITCH

4. TWO MICRO SWITCHES

5. TWO MICRO SWITCHES& FRAME

0. BASE1. HEVAC/

HVCA FRAME

2. ONE MICRO SWITCH

3. HEVAC FRAME & ONE MICRO SWITCH

4. TWO MICRO SWITCHES

5. TWO MICRO SWITCHES& FRAME

MATERIAL

0. GALV1. GRADE 430

S/S BLADES GALV CASE

2. GRADE 430S/S BLADES & CASING

0. GALV1. GRADE 430

S/S BLADES GALV CASE

2. GRADE 430S/S BLADES & CASING

PRODUCTGROUP

01

02THINWALL

FACE FITTING

0. BASE 1. RECTAN.

GULARSPIGOT

2. CIRCULARSPIGOT

3. FLAT OVAL SPIGOT

0. BASE 1. RECT

SPIGOT2. CIRCULAR

SPIGOT3. FLAT

OVAL SPIGOT

SECONDARYSIGNAL

ACTUATION0. BASE 1. ETL 5. SOLENOID6. MAGNET9. EML

0. BASE 1. ETL5. SOLENOID 6. MAGNET9. EML

MODEL

1. SLEEVE2. TOP

FLANGEMOUNT

3. SPIGOT4. SLEEVE5. RECT.

SPIGOT(BLADES

PARTLY IN

AIRSTREAM)6. SPIGOT

(BLADES

OUT OF

AIRSTREAM)

4. SLEEVE5. RECT.

SPIGOT(BLADES

PARTLY IN

AIRSTREAM)6. SPIGOT

(BLADES

OUT OF

AIRSTREAM)

PRODUCT CODING

0169-11

SIZE (W X H)MM QUANTITY FEATURES

300 X 300 10100% GALV. STEEL BLADES AND

CASING. HEVAC/HVCAINSTALLATION FRAMES E.M.L.

Other fully tested and approved product groups available include:

MODEL REF

MEMBER

Note: 430 Gradestainless steel is notsuitable for hostileor corrosiveenvironments.

(uk) limited curtain fire dampers

Documents