www.scientif icdri l l ing .com

TITAN 22 PERFORMANCE DRILLING MOTOR - 6½” 7/8 6.4PRODUCT SPEC SHEET

Updated May 2016

Copyright © 2016 Scientific Drilling International

General specificationsLength 33.8 ft (10.3 m)

OD 6.626 in (168 mm)

Recommended Hole Sizes 7 7/8 - 8 3/4 in (200 - 222 mm)

Max Bend Angle 2.38°

BearinG sectionBit to Bend Length 49 in (1.2 m)

Bit Box Connection 4½ in API Reg. Box

Max WOB 60,000 lbs (26,689 DaN)

Max Overpull for Rerun 105,000 lbs (46,706 DaN)

Overpull to Yield Motor 210,000 lbs (93,413 DaN)

Max Bit Pressure Drop 1,000 psi (6,894 kPA)

Opt. Bit Pressure Drop 100 - 750 psi (690 - 5,171 kPA)

LCM Capability 40 lb nut plug

power sectionLobe Configuration 7/8

Stages 6.4

Max Diff Pressure 1,440 psi (9,930 kPa)

Stall Diff Pressure 2,160 psi (14,890 kPa)

Torque at Max Diff Pressure 13,390 ft-lbs (18,160 Nm)

Stall Torque 20,090 ft-lbs (27,240 Nm)

Flow Range 300-600 gal/min (1,140 - 2,270 L/min)

Speed Range 86 - 180 RPM

Speed Ratio 0.29 rev/gal (0.076 rev/L)

Torque Slope 9.30 ft-lb/psi (1.829 Nm/kPa)

Specifications are subject to change without notice.

Ti-Flex™ Titanium Flex Shaft

Power Section

Bearing Assembly

Scientific Drilling’s Titan 22 performance drilling motor is designed for the most extreme drilling environments in the industry. It has been engineered to run with the highest torque power sections, delivering ultimate reliability and durability in all sections of the well.

The Titan 22 also features a unique Ti-Flex™ Titanium Flex Shaft and bearing pack assembly to deliver optimal performance in a wide range of applications.

DELIVERING THEULTIMATE VALUE

TARGET APPLICATIONS

• Enhanced WOB capacity supporting increased and consistent ROP for superior drilling performance

• Rugged driveline design for ultra-high power torque sections delivering maximized reliability

• Full rotational capabilities in all sections of the well ensuring optimal wellbore integrity

• Innovative Ti-Flex™ Titanium Flex Shaft and bearing assembly, for increased durability and extended tool life

• Performance Drilling

• Extended Reach Laterals

• Factory Drilling in Shale Reservoirs

• One Run Applications

• Laminated Formations

www.scientif icdri l l ing .com

TITAN 22 PERFORMANCE DRILLING MOTOR - 6½” 7/8 6.4PRODUCT SPEC SHEET

Updated May 2016

Copyright © 2016 Scientific Drilling International

Chart data is based on bending-moment limitations of the bent housing. The primary criteria used to establish these limit lines is the bending moment that results in the onset of shoulder separation at the bend. The Plot is representative of sustainable operation in a specific wellbore curvature (DLS). The chart only applies to slick motors and does not, in any way, attempt to predict build/drop tendencies of the BHA. DLS lines correspond to the wellbore curvature that the motor is currently in. If a particular bend assembly is in a curve that, according to the chart, prevents rotation then slowly rotate (30 RPM) until the motor has effectively drilled itself out of the curve. Prolonged rotation in a curve (>10 minutes) or sustained rotation rates above 30 RPM will accelerate fatigue in the motor and are considered out-of-spec operations. Configurations with stabilizers and special equipment need to be looked at on an individual basis.

Titan 22 6½” Estimated Rotation Limits in 7 7/8” Wellbore

Titan 22 6½” 7/8 6.4 Power Curve