drilling motor handbook - axon energy...

DRILLING MOTORHANDBOOK

GORILLA Drilling MotorsTM

rev2013.06.19

GORILLA Drilling Motors™

DRILLING MOTOR HANDBOOK

www.axonep.com

The information contained in this handbook is for reference only. AXON Downhole Products Inc. does not warrant,

nor guarantee the contents. The user assumes all liability and responsibility for use of the information contained

herein.


“At AXON, we embrace Alternative Thinking, we build oilfield Products that Perform, and we demand that Aftermarket is not an Afterthought.”

AXON Downhole Products, Inc. ▪ All Rights Reserved ▪ Specifications Subject to Change Without Notice

ii

Table of Contents

Motor Description…………………………………………………………………………… 1

Overview………………………………………………………………………………. 1

Top Sub………………………………………………………………………………… 1

Power Sections…………………………………………………………………….. 1

Adjustable Bend Housing…………………………………………………….. 2

Bearing Section……………………………………………………………………. 6

Drive Shaft………………………………………………………………………….. 7

Running In…………………………………………………………………………………….. 7

Drilling………………………………………………………………………………………….. 8

Tripping Out…………………………………………………………………………………. 8

Drilling Fluids…………………………………………………………………………………. 8

Downhole Temperature…………………………………………………………………. 9

Servicing………………………………………………………………………………………... 9

Motor Specifications………………………………………………………………………. 10

3-3/4”, 4/5, 3.5 Stages…………………………………………………………. 11

3-3/4”, 5/6, 5.0 Stages…………………………………………………………. 13

3-3/4”, 6/7, 3.0 Stages………………………………………………………… 15

3-3/4”, 7/8, 2.0 Stages…………………………………………………………. 17




iii

3-3/4”, 7/8, 2.3 Stages………………………………………………………… 19

3-3/4” Motor Tool Joint Torque Specifications………………… 21

Fishing Diagram – 3-3/4 Inch Motors……………………………….. 22

4-3/4”, 4/5, 3.5 Stages…………………………………………………………… 23

4-3/4”, 4/5, 6.0 Stages…………………………………………………………… 25

4-3/4”, 4/5, 6.3 Stages…………………………………………………………… 27

4-3/4”, 5/6, 8.3 Stages…………………………………………………………… 29

4-3/4”, 7/8, 2.0 Stages…………………………………………………………… 31

4-3/4”, 7/8, 2.2 Stages…………………………………………………………… 33

4-3/4”, 7/8, 2.9 Stages…………………………………………………………… 35

4-3/4”, 7/8, 3.8 Stages…………………………………………………………… 37

4-3/4” Motor Tool Joint Torque Specifications……………………….. 39

Fishing Diagram – 4-3/4 Inch Motors…………………………………….. 40

6-3/4”, 4/5, 4.8 Stages……………………………………………………. 41

6-3/4”, 4/5, 7.0 Stages……………………………………………………. 43

6-3/4”, 5/6, 5.0 Stages…………………………………………………….. 45

6-3/4”, 5/6, 6.8 Stages…………………………………………………….. 47

6-3/4”, 6/7, 5.0 Stages……………………………………………………… 49

6-3/4”, 6/7, 6.0 Stages……………………………………………………… 51




iv

6-3/4”, 7/8, 2.0 Stages……………………………………………………… 53

6-3/4”, 7/8, 3.0 Stages………………………………………………………. 55

6-3/4”, 7/8, 5.0 Stages………………………………………………………. 57

6-3/4”, 7/8, 6.4 Stages……………………………………………………….. 59

6-3/4” Motor Tool Joint Torque Specifications…………………… 61

Fishing Diagram – 6-3/4 Inch Motors…………………………………. 62

8”, 4/5, 3.6 Stages……………………………………………………………… 63

8”, 4/5, 5.3 Stages……………………………………………………………… 65

8”, 5/6, 3.0 Stages…………………………………………………………….. 67

8”, 5/6, 5.0 Stages……………………………………………………………… 69

8”, 6/7, 4.0 Stages……………………………………………………………… 71

8”, 6/7, 5.0 Stages……………………………………………………………… 73

8”, 7/8, 3.0 Stages……………………………………………………………… 75

8”, 7/8, 4.0 Stages……………………………………………………………… 77

8” Motor Tool Joint Torque Specifications…………………………. 79

Fishing Diagram – 8 Inch Motors……………………………………….. 80

9-5/8”, 5/6, 3.0 Stages………………………………………………………. 81

9-5/8”, 5/6, 4.0 Stages………………………………………………………. 83

9-5/8”, 6/7, 5.0 Stages……………………………………………………….. 85




v

9-5/8”, 6/7, 6.0 Stages………………………………………………………. 87

9-5/8” Motor Tool Joint Torque Specifications……………….. 89

Fishing Diagram – 9-5/8 Inch Motors………………………………… 90

11-1/4”,6/7, 5.5 Stages……………………………………………………….. 91

11-1/4” Motor Tool Joint Torque Specifications………………….. 93

Fishing Diagram – 11-1/4 Inch Motor………………………………… 94

Coiled Tubing Motors……………………………………………………….. 95

1-11/16”, 5/6, 2.3 Stages………………………………………………….. 95

1-11/16”, 5/6, 2.5 Stages………………………………………………….. 97

1-11/16”, 5/6, 4.4 Stages……………………………………………………. 99

1-11/16” Motor Tool Joint Torque Specifications………….….. 101

Fishing Diagram – 1-11/16 Inch Motors……………………………… 102

2-3/8”, 5/6, 2.5 Stages……………………………………………………… 103

2-3/8” Motor Tool Joint Torque Specifications………………….. 105

Fishing Diagram – 2-3/8 Inch Motor………………………………….. 106

2-7/8”, 5/6, 3.3 Stages………………………………………………………. 107

2-7/8, 5/6, 7.0 Stages……………………………………………………….. 109

2-7/8”, 7/8, 2.5 Stages………………………………………………………. 111

2-7/8” Motor Tool Joint Torque Specifications…………………... 113




vi

Fishing Diagram – 2-7/8 Inch Motors…………………………………… 114

Useful Conversion Factors……………………………………………….… 115




1

Directional Drilling Motors

Overview

As shown in Figure 1, downhole motors are comprised of a top sub, power

section, adjustable bend housing, bearing pack assembly and bit box.

Internally, the power section rotor is normally supplied with a rotor catch on

top, a CV-type flex coupling on the bottom that converts the eccentric

rotation of the rotor to pure rotary, a stackable arrangement of radial and

thrust bearings to take side loads and on-bottom/off-bottom axial loads, a

drive shaft and various seals.

Top Sub:

The top sub box thread is available in several options for each motor size.

These options are listed in the motor performance section. Please specify

the top sub connection when ordering.

Power Sections:

The function of the power section is to convert a portion of the hydraulic

energy of the drilling motor (in the form of pressure and flow) into

mechanical power in the form of rotation and torque. The power section

consists of a fluted rotor and a rubber lined stator where the stator has one

more lobe than the rotor.

All directional drilling motors are offered in a wide range of rotor/stator

lobe configurations and stage lengths – allowing matching the motor

torque, speed and pressure differential characteristics to the specific drilling

application. AXON Downhole Products offers directional motors from 3-3/4

inched to 11-1/4 inches and coiled tubing motors from 1-11/16 to 2-7/8

inches. The coiled tubing motors are included in the last portion of the

Motor Specifications section.

The upper end of the rotor is fitted with a fishing neck to prevent Figure 1




2

component loss in the event of a failure. Rotors are normally provided solid but can be gunned

drilled to accept a bypass nozzle upon request.

The lower end of the rotor is threaded onto a CV-type coupling which converts the eccentric

motion into pure rotary motor. The Downhole end of the CV-type coupling connects to the

drive shaft. Drilling torque is transmitted through a multi-ball and socket arrangement.

Adjustable Bend Housing:

All GORILLA’S directional drilling motors feature a 20-step, 0 – 3 degree adjustable bend

housing which can be set in the shop or on the rig floor. [Motors can also be provided with fixed

bend housings on request.]

By setting this housing to various degree settings, it is possible to achieve a wide range of build

rates. Build rates for each motor combination can be found in the Motor Specification sheets

starting on page 11. The predicted build rates are based on the 3-point arc defined by the drill

bit, the bit-to-bend distance and size of the kick pad (or stabilizer size) and the overall motor

length as shown below. Realistic bit lengths have been used in these calculations.

Figure 2.

Actual build rates can vary from the predicted rates. Build rate is dictated by a number of

factors including (1) drill bit characteristics especially gauge length and side cutting ability, (2)

weight on bit where higher weights generally increase build rates ; (3) overall motor length; (4)

bit-to-bend distance; (5) location and outer dimensions of the wear pad and/or stabilizers and

(5) formation ansiotrophy.




3

When running slick stabilizers, the build rate for a given motor decreases with increasing hole

size. For stabilized motors. The build rate increases with increasing hole size. The build rates in

this manual assume the stabilizer is 1/8 inch under-gauge.

Care must be shown regarding rotating bent housing motors in the hole. In general, motors set

with bends above 1.83 degrees should not be rotated in the hole. RPM should be limited to no

more than 60 rpm if possible.

The procedure for setting the adjustable bend housing is described in the figures below.

Figure 3 - Step A

1. Place Tongs on the ABH Upper Mandrel. 2. Loosen the ABH Lock Sleeve Approximately 1 Turn. 3. Raise the ABH Pad Sleeve to Disengage Alignment Teeth.

3

ABH Upper Mandrel

1. “TONG HERE”

“TONG HERE”

2

ABH Lock Sleeve

1. “TONG HERE”

“TONG HERE”




4

Figure 4 - Step B

1. Hold ABH Upper Mandrel. 2. Place Tongs and Turn ABH Lower Housing (Clockwise or Counterclockwise) to Align Desired

Angle (Stamped On ABH Lower Housing) with Bend Indicator (Stamped On ABH Pad Sleeve).

ABH Upper Mandrel

1. “TONG HERE” - HOLD

“TONG HERE”

2

Align “Bend” Indicator

With Desired Angle

“TONG HERE”

ABH Lower Housing

2. “TONG HERE” - TURN

“TONG HERE”




5

Figure 5 - Step C

1. Lower ABH Pad Sleeve to Reengage Alignment Teeth. 2. Turn the ABH Lock Sleeve to contact face of ABH Pad Sleeve. 3. Place Tongs on ABH Upper Mandrel and ABH Lock Sleeve and Apply Specified Torque.

Motor Size ABH Lock Sleeve Make-Up Torque

3-3/4” 3,500 Lbs-Ft (4745 N-m)

5”/4-3/4” 9,000 Lbs-Ft (12,202 N-m)

6-3/4” 25,000 Lbs-Ft (33,895 N-m)

8” 40,000 Lbs-Ft (54,233 N-m)

9-5/8” 60,000 Lbs-Ft (81,349 N-m)

11-1/4” 75,000 Lbs-Ft (101,687 N-m)

ABH Upper Mandrel

3. “TONG HERE”

“TONG HERE”

2

ABH Upper Mandrel

3. “TONG HERE”

“TONG HERE”

1




6

Bearing Section:

All AXON Directional Drilling Motors (DDM) feature sealed, pressure compensated bearing

sections. State of the art rotary seals are employed at each end of the bearing section to

prevent drilling mud from entering the bearing housing while sealing in lubricating oil. Upper

and lower seals have equivalent sealing diameters.

Pressure compensation is achieved through a sealed floating ring located just above the bit box

on the pilot diameter of the drive shaft. This piston prevents high differential pressure across

the rotary seals as well as compensates for increases in oil volume when high temperatures are

encountered. The compensator piston rotates with the drive shaft and bearing shaft transition

ring thereby avoiding the need for a rotary seal on the compensator piston. Weep holes located

at the lower end of the drive shaft allows bit pressure exposure to one side of the compensator

piston providing a positive pressure inside the bearing housing - further discouraging mud

invasion into the bearing section.

Each bearing section utilizes high capacity roller thrust bearings. For all but the 3-3/4” motors,

the thrust bearings are stackable in either a 4:2 or 3:3 on bottom/off bottom arrangements to

optimize load capacities to expected drilling conditions. Each thrust bearing is backed with a

“Belleville style” spring washer which serves to evenly distribute the load over multiple

bearings and provide shock load cushioning created while drilling. All bearing components are

held in compression within the assembly to prevent rotation. Rotating and stationary sleeves

are pre-machined to length to provide proper Belleville spring preloading. This stackable

bearing arrangement serves to minimize diametric step changes along the shaft length thus

reducing stress concentrations produced by shoulders and grooves.

Each bearing section utilizes high capacity roller radial bearings. Radial bearing sets are spaced

apart with sleeves to provide higher radial load carrying capacities. Bearing sets, top and

bottom provide radial support to the drive shaft as well as the rotary seal preventing wear and

extending seal life.

A drive shaft lock nut is located between the thrust bearing stack and the lower radial bearing.

The lock nut ring is threaded (left hand thread) onto the drive shaft, and once installed, serves

to compress the inner races of the lower radial bearing and the lower transition ring to prevent

rotation relative to the drive shaft. The lower lock nut will not pass through the lower seal sub




7

so in case of a failure in the upper area of the drive shaft the lock nut will prevent component

loss from the bearing assembly.

A drive shaft cap threads to the upper part of the drive shaft and serves to compress all rotating

components preventing rotation relative to the drive shaft. It also serves to divert mud flow

into the drive shaft bore. Diverter slots are optimized to minimize pressure loss at higher mud

flow rates and case hardened to minimize erosion from the mud flow turbulence. The outer

diameter of the drive shaft cap is hard chrome plated to provide a hardened and ground

running surface for the rotary seal.

The bearing section outer housing is upset and threaded to accept replaceable centralizer

sleeves of any size. A centralizer blank sleeve is available in cases where centralizers are not

used.

Drive Shaft

The drive shafts are forged for high strength with a 140 KSI MYS. The drive shafts cross-sections

have been made as large as possible within available design constraints. The end of the drive

shaft has an API regular box connection for connecting the drill bit.

Running In

Care should always be exercised regarding tripping speeds when running in the hole to prevent

striking BOP components, casing shoes, bridges or shelves which may be in the borehole. Tight

spots should be addressed by operating the mud pumps and slowly reaming through the

restrictions. In addition, the motor should be started by circulating off bottom to prevent

possible plugging of the drill bit nozzles. Errors in pipe tallying or cuttings backfill in the bottom

of the hole always dictate slow tripping speeds when approaching bottom.

It is important to record circulating off-bottom standpipe pressure at a known flow rate. The

pressure difference above the off-bottom pressure is a measure of the torque being demanded

from the motor while it is drilling. In fact, motor pressure differential is proportional to bit

torque. It is not recommended to exceed maximum differential pressure in the motor curves

provided in this handbook as this will reduce stator life.




8

Drilling

Start the mud pumps and slowly bring up the flow until the desired flow rate has been achieved

and is stabilized. Slowly lower the motor to bottom. On bottom will be evidence by an increase

in standpipe pressure. Gradually increase weight on bit to achieve optimal rate of penetration.

Continue to monitor motor pressure differential, ROP and adjust WOB accordingly. As the bit

drills off, WOB and standpipe pressure will decrease until WOB is readjusted.

Application of too high of bit weight can cause the mud motor to stall. When stalled, the rotor

is no longer turning and fluid is trying to be forced back up the drill pipe. This creates a dead-

head type condition which can cause damage to the power section. Therefore stalling should

be avoided.

The following actions should be taken when the motor is in a stalled condition:

1. Stop drill string rotation

2. Reduce pump strokes

3. Do not pick up off bottom until the lock-up torque of the motor has been dissipated

using the rotary table break to minimize the possibility of connection back offs.

4. Pick up off bottom and re-establish drilling parameters.

Tripping Out

Prior to tripping out, circulate bottoms up. Tripping speeds should be controlled to prevent hole

swabbing. Speeds should also be slowed when approaching known tight spots, high build rate

intervals and casing points, etc. Extended back-reaming should be avoided as it shortens motor

life.

At the surface, visually inspect the motor to check for external damage prior to re-run.

Drilling Fluid

The directional drilling motors can be operated with both water- and oil-based drilling fluids.

The aniline point for oil-based muds is the temperature at which the stator’s nitrile or HSN

rubber swells. The lower the aniline point the greater the swelling. Aniline points should

generally be kept above 160 to prevent swelling.




9

Highly saturated brines can shorten rotor life due to corrosion. Chloride content should not

exceed 30,000 ppm when using hard chrome rotors. Motors run in these conditions (> 30,000

ppm chloride) should be immediately flushed with clean water after pulling out of the hole and

serviced as soon as practical to minimize corrosion impacts.

It is recommended that sand content not exceed 3% and total solids not exceed 5%. Mud

weights in excess of 16 ppg will shorten power section life.

If flow rates higher than the maximum recommended flow rate for a given power section are

required, the rotor can be gun-drilled and fitted with a bypass nozzle. Please contact your

AXON representative to assist you in nozzle sizing. Gun-drilled rotors can be blocked by

installing a blanked nozzle.

Downhole Temperature

Standard fit rotor/stators are normally used when hole temperatures are less than 250°F

degrees (120 °C). For higher temperatures, standard practice is to reduce the rotor/stator fit to

compensate for the rubber swelling. Be aware that reduced fit rotor/stator combinations

require the rubber be hot to produce the desired horsepower and will have degraded

performance if run in cooler hole sections.

Servicing

Motors should be disassembled, cleaned and thoroughly inspected upon return from the field.

The majority of items can be re-run providing they are still in specification. Please consult your

maintenance and assembly manual provided with your purchase.

O-rings used in the multi-ball socket arrangement on both ends of the coupling should be

replaced each time the motor returns from the field and the joints should be repacked with

grease. In addition, the rotary seals located on both ends of the sealed bearing pack should be

replaced.




10

MOTOR SPECIFICATIONS

The following section contains important information for each motor operation. Motors should

not be operated above the pressure differential at maximum torque provided in the tables.




11

3-3/4” Motor, 4/5 Lobe Configuration, 3.5 Stages

Lobe Configuration 4/5 – 3.5 Stages

Overall Length 215 inches (5.46 meters)

Bit-to-Bend 43.25 inches (1.098 meters)

Common Box Connections 2-7/8 Reg., 2-3/8 IF

Bit Size 4-1/2” – 5-7/8” (114.3 mm – 149.2 mm)

Maximum Flow Rate 160 GPM (606 LPM)

Minimum Flow Rate 100 GPM (378 LPM)

RPM per Unit Flow @ No Load 1.5 Revs/Gallon (0.40 Revs/Liter)

Maximum Operating Torque 675 Lbs-Ft (915 N-m)

Differential Pressure at Max. Operating Torque 500 PSI (3447 KPa)

Horsepower at Maximum Flow 27.5 HP (20.5 KW)

Horsepower at Minimum Flow 12. 5 HP (9.3 KW)

Maximum Weight-on-Bit 46,800 Lbs (208.18 kN) Dynamic 192,300 Lbs (855.39 kN) Static

Maximum Overpull (Re-Run) 128,200 Lbs (570.26 kN)

Motor Yield 180,000 Lbs (800.68 kN)

ABH Sleeve Recommended Make-Up Torque 3500 Lbs-Ft (4745 N-m)

Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 3500 Lbs-Ft (4745 N-m)

0

100

200

300

400

500

600

700

800

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft

Differential Pressure - PSI

Min Flow

Max Flow




12

Predicted Build Rate in Degrees per 100 Ft.

Bend Angle ° Slick Assembly Stabilized

4-3/4” Hole 5-7/8” Hole 4-3/4” Hole 5-7/8” Hole

0.39 1.60 1.29 6.46

0.59 3.74 3.46 8.01

0.78 5.78 5.52 9.48

0.96 7.71 1.10 7.47 10.87

1.15 9.75 3.18 9.53 12.34

1.33 11.68 5.07 11.48 13.73

1.50 13.50 6.89 13.32 15.04

1.67 15.32 8.71 15.16 16.35

1.83 17.04 10.43 16.90 17.59

1.98 18.65 12.04 18.52 18.75

2.12 20.15 13.54 20.04 19.83

2.38 22.93 16.32 22.86 21.84

2.49 24.11 17.50 24.05 22.69

2.60 25.29 18.68 25.24 23.54

2.77 27.11 20.50 27.09 24.85

2.90 28.51 21.90 28.50 25.86

3.00 29.58 22.97 29.58 26.63

0

50

100

150

200

250

0 100 200 300 400 500 600

RP

M


100 GPM

160 GPM




13






Bit Size 4-1/2” – 5-7/8” (114.3 mm – 149.2 mm)






Horsepower at Maximum Flow 50 HP (37.3 KW)

Horsepower at Minimum Flow 30 HP (22.4 KW)






0

200

400

600

800

1000

1200

1400

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




14


Bend Angle (°) Slick Assembly Stabilized


0.39 1.25 1.44 7.73

0.59 3.07 3.25 8.63

0.78 4.81 4.97 9.48

0.96 6.45 0.81 6.60 10.29

1.15 8.19 2.54 8.32 11.14

1.33 9.83 4.19 9.95 11.95

1.50 11.38 5.74 11.49 12.71

1.67 12.93 7.29 13.03 13.47

1.83 14.39 8.75 14.48 14.19

1.98 15.76 10.12 15.84 14.86

2.12 17.04 11.40 17.10 15.49

2.38 19.41 13.78 19.46 16.66

2.49 20.41 14.78 20.45 17.15

2.60 21.42 15.79 21.45 17.65

2.77 22.97 17.34 22.99 18.41

2.90 24.16 18.53 24.16 18.99

3.00 25.07 19.44 25.07 19.44

0

50

100

150

200

250

300

0 200 400 600 800 1000

RP

M


100 GPM

140 GPM

160 GPM




15






Bit Size 4-1/2” – 5-7/8” (114.3 mm – 149.2 mm)






Horsepower at Maximum Flow 23. 8 HP (17.7 KW)

Horsepower at Minimum Flow 12. 5 HP (9.3 KW)






0

200

400

600

800

1000

1200

1400

0 200 400 600 800

Torq

ue

Lb

s-Ft

Differential Pressure

Min Flow

Max Flow




16




0.39 1.40 1.38 4.32

0.59 3.37 3.36 6.03

0.78 5.25 5,24 7.66

0.96 7.03 7.02 9.19

1.15 8.91 2.82 8.90 10.82

1.33 10.69 4.60 10.68 12.36

1.50 12.37 6.28 12.36 13.81

1.67 14.05 7.96 14.04 15.26

1.83 15.36 9.54 15.62 16.63

1.98 17.12 11.02 17.11 17.91

2.12 18.50 12.41 18.49 19.11

2.38 21.07 14.97 21.07 21.33

2.49 22.16 16.06 22.15 22.27

2.60 23.25 17.15 23.24 23.21

2.77 24.93 18.83 24.92 24.66

2.90 26.21 20.11 26.211 25.78

3.00 27.20 21.10 27.20 26.63

0

20

40

60

80

100

120

140

160

180

0 100 200 300 400 500 600

RP

M


80 GPM

140 GPM

200 GPM




17






Bit Size 4-1/2” – 5-7/8” (114.3 mm – 149.2 mm)





Differential Pressure at Max. Operating Torque 438 PSI (3020 kPa)

Horsepower at Maximum Flow 15.5 HP (11.55 kW)






0

200

400

600

800

1000

1200

1400

1600

1800

0 100 200 300 400 500

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




18




0.39 1.40 1.38 4.32

0.59 3.37 3.36 6.03

0.78 5.25 5,24 7.66

0.96 7.03 7.02 9.19

1.15 8.91 2.82 8.90 10.82

1.33 10.69 4.60 10.68 12.36

1.50 12.37 6.28 12.36 13.81

1.67 14.05 7.96 14.04 15.26

1.83 15.36 9.54 15.62 16.63

1.98 17.12 11.02 17.11 17.91

2.12 18.50 12.41 18.49 19.11

2.38 21.07 14.97 21.07 21.33

2.49 22.16 16.06 22.15 22.27

2.60 23.25 17.15 23.24 23.21

2.77 24.93 18.83 24.92 24.66

2.90 26.21 20.11 26.211 25.78

3.00 27.20 21.10 27.20 26.63


0

10

20

30

40

50

60

70

80

90

100

-50 50 150 250 350 450

RP

M


100 GPM

130 GPM

160 GPM




19





Bit Size 4-1/2” – 5-7/8” (114.3 mm – 149.2 mm)












0

200

400

600

800

1000

1200

0 100 200 300 400 500

Torq

ue

Lb

s-Ft


100 GPM

160 GPM




20




0.39 1.60 1.29 6.46

0.59 3.74 3.46 8.01

0.78 5.78 5.52 9.48

0.96 7.71 1.10 7.47 10.87

1.15 9.75 3.18 9.53 12.34

1.33 11.68 5.07 11.48 13.73

1.50 13.50 6.89 13.32 15.04

1.67 15.32 8.71 15.16 16.35

1.83 17.04 10.43 16.90 17.59

1.98 18.65 12.04 18.52 18.75

2.12 20.15 13.54 20.04 19.83

2.38 22.93 16.32 22.86 21.84

2.49 24.11 17.50 24.05 22.69

2.60 25.29 18.68 25.24 23.54

2.77 27.11 20.50 27.09 24.85

2.90 28.51 21.90 28.50 25.86

3.00 29.58 22.97 29.58 26.63

0

20

40

60

80

100

120

140

0 100 200 300 400 500

RP

M


100 GPM

130 GPM

160 GPM




21

3-3/4” Motor Tool Joint Torque Specifications

Motor Size

3.75 Inch

Thread Torque Lbs-Ft Torque N-m

Top Sub Box Up

2 3/8 IF 3700 - 4000 5016 - 5423

2 3/8 REG 4000-4500 5423 - 6101

Pin Down 3 1/8 ADHP 3500 4745

Stator Tube Box Up 3 1/8 ADHP 3500 4745

Box Down 3 1/8 ADHP 3500 4755

ABH/Stator X-Over Pin Up 3 1/8 ADHP 3500 4745

Pin Down 3 1/8 ADHP 3500 4745

Adjustable Bend Housing Sub-Assembly

Box Up 3 1/8 ADHP 3500 4745

Pin Down 3 1/8 ADHP 3500 4745

Bearing Pack Housing Box Up 3 1/8 ADHP 3500 4745

Box Down SA-LEFT HAND

2500 3390

Lower Seal Sub Pin Up

SA-LEFT HAND

2500 3390

Bit Box Box Down

2 3/8 IF 3700 - 4000 5016 - 5423

2 3/8 Reg 4000-4500 5423 – 6101




22

Fishing diagram – 3-3/4 Inch Motor




23



Overall Length 203.5 inches (5.17 meters)



Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)






Horsepower at Maximum Flow 47 HP (35 KW)


Maximum Weight-on-Bit 4:2 Bearing Configuration 3:3 Bearing Configuration

77,600 Lbs (345.2 kN) Dynamic 310,400 Lbs (1380.7 kN) Static 58,200 Lbs (258.9 kN) Dynamic 232,800 Lbs (1035.5 kN) Static

Maximum Overpull (Re-Run) 155,200 Lbs (690.4 kN) for 4:2 Configuration 232,200 Lbs (1032.9 kN) for 3:3 Configuration


ABH Sleeve Recommended Make-Up Torque 9000 Lbs-Ft (12,202 N-m)

Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6000 Lbs-Ft ( 8,135 N-m)

0

200

400

600

800

1000

1200

0 100 200 300 400 500 600

Torq

ue

(Lb

s-Ft

)


Min Flow

Max Flow




24

Predicted Build Rates in Degrees per 100 Ft

Bend Angle (°)

SLICK STABILZED

6” Hole 6-1/4” Hole 6-3/4” Hole 6” Hole 6-1/4” Hole 6-3/4” Hole

0.39 2.78 1.43 2.78 1.08 4.54

0.59 5.04 3.69 0.97 5.04 3.37 6.36

0.78 7.19 5.84 3.12 7.19 5.54 8.08

0.96 9.22 7.87 5.16 9.22 7.60 9.72

1.15 11.37 10.02 7.31 11.37 9.78 11.45

1.33 13.41 12.06 9.35 13.41 11.84 13.08

1.50 15.33 13.98 11.27 15.33 13.78 14.63

1.67 17.25 15.90 13.19 17.25 15.72 16.18

1.83 19.06 17.71 15.00 19.06 17.56 17.63

1.98 20.76 19.41 16.70 20.76 19.27 18.99

2.12 22.34 20.99 18.28 22.34 20.87 20.27

2.38 25.28 23.93 21.23 25.28 23.85 22.63

2.49 26.52 25.17 22.47 26.52 25.11 23.63

2.60 27.77 26.42 23.71 27.77 26.36 24.63

2.77 29.70 28.34 25.64 29.70 28.31 26.18

2.90 31.16 29.81 27.11 31.16 29.80 27.36

3.00 32.39 30.94 28.24 32.39 30.94 28.27

0

50

100

150

200

250

300

0 100 200 300 400 500 600

RP

M


100 GPM

150 GPM

200 GPM

250 GPM




25






Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)







Horsepower at Minimum Flow 12.8 HP (9.5 KW)





ABH Sleeve Recommended Make-up Torque 9000 Lbs-Ft (12,202 N-m)


0

200

400

600

800

1000

1200

1400

1600

1800

2000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




26


Bend Angle (°)

SLICK STABILZED


0.39 1.90 0.86 1.90 1.47 3.14

0.59 3.64 2.60 0.51 3.64 3.17 4.63

0.78 5.30 4.26 2.17 5.30 4.78 6.04

0.96 6.87 5.83 3.74 6.87 6.31 7.38

1.15 8.53 7.49 5.40 8.53 7.92 8.79

1.33 10.10 9.06 6.97 10.10 9.45 10.13

1.50 11.58 10.54 8.45 11.58 10.89 11.39

1.67 13.06 12.02 9.93 13.06 12.33 12.65

1.83 14.46 13.42 11.33 14.45 13.69 13.84

1.98 15.77 14.73 12.64 15.77 14.96 14.96

2.12 16.99 15.95 13.86 16.99 16.15 16.00

2.38 19.25 18.21 16.12 19.25 18.36 17.93

2.49 20.21 19.17 17.08 20.21 19.29 18.75

2.60 21.17 20.13 18.04 21.17 20.23 19.57

2.77 22.65 21.64 19.52 22.65 21.67 20.83

2.90 23.79 22.75 20.66 23.79 22.77 21.80

3.00 24.66 23.62 21.53 24.66 23.62 22.54

0

50

100

150

200

250

300

0 200 400 600 800 1000

RP

M


250 GPM

175 GPM

100 GPM




27





Common Box Connections 3-1/2 Reg., 3=1/2 IF

Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)














0

200

400

600

800

1000

1200

1400

1600

1800

2000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




28


Bend Angle (°)

SLICK STABILZED


0.39 1.71 0.75 1.71 1.51 2.82

0.59 3.32 2.36 0.43 3.32 3.07 4.22

0.78 4.86 3.90 1.97 4.86 4.55 5.54

0.96 6.31 5.35 3.42 6.31 5.95 6.80

1.15 7.84 6.88 4.95 7.84 7.43 8.13

1.33 9.30 8.34 6.41 9.30 8.83 9.38

1.50 10.67 9.71 7.78 10.67 10.15 10.57

1.67 12.04 11.08 9.15 12.04 11.47 11.76

1.83 13.33 12.37 10.44 13.33 12.72 12.87

1.98 14.55 13.59 11.66 14.54 13.88 13.92

2.12 15.68 14.72 12.79 15.68 14.97 14.90

2.38 17.77 16.81 14.88 17.77 17.00 16.71

2.49 18.66 17.70 15.77 18.66 17.85 17.48

2.60 19.55 18.59 16.66 19.55 18.71 18.25

2.77 20.92 19.96 18.03 20.92 20.03 19.44

2.90 21.97 21.01 19.08 21.97 21.04 20.34

3.00 22.78 21.82 19.89 22.78 21.82 21.04

0

50

100

150

200

250

300

0 200 400 600 800 1000

RP

M

Differential Preesure - PSI

100 GPM

150 GPM

200 GPM

250 GPM




29




Bit-to-Bend 45.78 inches (1.16 meters


Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)










Maximum Overpull (Re-Run) 155,200 Lbs (690.4 kN) for 4:2 Configuration 232,200 Lbs(1032.9 kN) for 3:3 Configuration




0

500

1000

1500

2000

2500

3000

0 500 1000 1500

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




30


Bend Angle (°)

SLICK STABILZED


0.39 1.47 2.20 1.47 1.52 2.42

0.59 2.91 3.52 0.32 2.91 2.90 3.69

0.78 4.29 4.78 1.70 4.29 4.20 4.90

0.96 5.59 5.97 3.00 5.59 5.44 6.05

1.15 6.96 7.23 4.37 6.96 6.74 7.26

1.33 8.26 8.42 5.67 8.26 7.98 8.40

1.50 9.49 9.54 6.90 9.49 9.15 9.48

1.67 10.72 10.66 8.13 10.72 10.32 10.56

1.83 11.87 11.72 9.28 11.87 11.42 11.58

1.98 12.96 12.71 10.37 12.96 12.45 12.53

2.12 13.97 13.64 11.38 13.97 13.41 13.42

2.38 15.85 15.36 13.26 15.85 15.20 15.08

2.49 16.64 16.09 14.05 16.64 15.95 15.78

2.60 17.44 16.81 14.85 17.44 16.71 16.48

2.77 18.67 17.94 16.08 18.67 17.88 17.56

2.90 19.61 18.80 17.02 19.61 18.77 18.38

3.00 20.33 19.46 17.74 20.33 19.46 19.02

0

50

100

150

200

250

300

350

0 500 1000 1500

RP

M


150 GPM

200 GPM

250 GPM

300 GPM




31






Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)










Maximum Overpull (Re-Run) 155,200 Lbs (690.4 kN) for 4:2 Configuration 232,200 Lbs (1032.9 kN)for 3:3 Configuration



Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 6000 Lbs-FT ( 8,135 N-m)

0

500

1000

1500

2000

2500

3000

0 100 200 300 400

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




32


Bend Angle (°)

SLICK STABILZED


0.39 1.93 0.88 1.94 1.50 3.20

0.59 3.71 2.65 0.52 3.71 3.23 4.72

0.78 5.40 4.34 2.21 5.40 4.87 6.16

0.96 7.00 5.94 3.81 7.00 6.43 7.52

1.15 8.69 7.63 5.50 8.69 8.07 8.96

1.33 10.30 9.23 7.10 10.29 9.63 10.32

1.50 11.80 10.74 8.61 11.8 11.10 11.61

1.67 13.31 12.25 10.12 13.31 12.60 12.90

1.83 14.73 13.67 11.54 14.73 13.95 14.11

1.98 16.07 15.00 12.88 16.07 15.25 15.25

2.12 17.31 16.25 14.12 17.31 16.46 16.31

2.38 19.62 18.56 16.43 19.62 18.71 18.27

2.49 20.60 19.54 17.41 20.60 19.66 19.11

2.60 21.58 20.52 18.39 21.58 20.61 19.94

2.77 23.09 22.03 19.90 23.09 22.08 21.23

2.90 24.24 23.18 21.05 24.24 23.21 22.21

3.00 25.13 24.07 21.94 25.13 24.07 22.97

0

10

20

30

40

50

60

70

80

90

0 100 200 300 400

RP

M


100 GPM

150 GPM

200 GPM

250 GPM




33






Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)














0

200

400

600

800

1000

1200

1400

1600

1800

2000

0 100 200 300 400 500

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




34


Bend Angle (°)

SLICK STABILZED


0.39 2.78 1.43 2.78 1.08 4.54

0.59 5.04 3.69 0.97 5.04 3.37 6.36

0.78 7.19 5.84 3.12 7.19 5.54 8.08

0.96 9.22 7.87 5.16 9.22 7.60 9.72

1.15 11.37 10.02 7.31 11.37 9.78 11.45

1.33 13.41 12.06 9.35 13.41 11.84 13.08

1.50 15.33 13.98 11.27 15.33 13.78 14.63

1.67 17.25 15.90 13.19 17.25 15.72 16.18

1.83 19.06 17.71 15.00 19.06 17.56 17.63

1.98 20.76 19.41 16.70 20.76 19.27 18.99

2.12 22.34 20.99 18.28 22.34 20.87 20.27

2.38 25.28 23.93 21.23 25.28 23.85 22.63

2.49 26.52 25.17 22.47 26.52 25.11 23.63

2.60 27.77 26.42 23.71 27.77 26.36 24.63

2.77 29.70 28.34 25.64 29.70 28.31 26.18

2.90 31.16 29.81 27.11 31.16 29.80 27.36

3.00 32.39 30.94 28.24 32.39 30.94 28.27

0

20

40

60

80

100

120

140

160

0 100 200 300 400 500

RP

M


100 GPM

150 GPM

200 GPM

250 GPM




35






Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)



RPM per Unit Flow @ No Load 0.30 Revs/Gallon (.079 Revs/Liter)






77,600 Lbs Dynamic 310,400 Lbs Static 58,200 Lbs Dynamic 232,800 Lbs Static

Maximum Overpull (Re-Run) 155,200 Lbs for 4:2 Configuration 232.200 Lbs for 3:3 Configuration

Motor Yield 350,000 Lbs



0

500

1000

1500

2000

2500

3000

3500

4000

4500

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




36


Bend Angle (°)

SLICK STABILZED


0.39 1.43 0.57 1.43 1.51

0.59 2.84 1.99 0.31 2.84 2.85

0.78 4.18 3.33 1.65 4.18 4.13

0.96 5.45 4.60 2.92 5.45 5.33 1.31

1.15 6.79 5.94 4.26 6.79 6.61 2.92

1.33 8.06 7.21 5.53 8.06 7.81 4.45

1.50 9.26 8.41 6.73 9.26 8.95 5.89

1.67 10.46 9.61 7.93 10.46 10.09 7.33

1.83 11.59 10.74 9.06 11.59 11.16 8.69

1.98 12.65 11.80 10.12 12.65 12.17 9.96

2.12 13.63 12.78 11.10 13.63 13.10 11.15

2.38 15.47 14.62 12.94 15.47 14.85 13.35

2.49 16.24 15.40 13.71 16.24 15.58 14.29

2.60 17.02 16.18 14.49 17.02 16.32 15.22

2.77 18.22 17.38 15.69 18.22 17.46 16.66

2.90 19.13 18.29 16.60 19.13 18.33 17.76

3.00 19.84 19.00 17.31 19.84 19.00 18.61

0

10

20

30

40

50

60

70

80

90

0 100 200 300 400 500 600

RP

M


100 GPM

150 GPM

200 GPM

250 GPM




37



Overall Length 266. 5 inches (6.77 meters)



Bit Size 5-3/4” – 6-3/4” (146 mm – 171.5 mm)












ABH Sleeve Recommend Make-Up Torque 9000 Lbs-Ft (12,202 N-m)


0

500

1000

1500

2000

2500

3000

0 200 400 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




38


Bend Angle (°)

SLICK STABILZED


0.39 1.90 0.86 1.90 1.47 3.14

0.59 3.64 2.60 0.51 3.64 3.17 4.63

0.78 5.30 4.26 2.17 5.30 4.78 6.04

0.96 6.87 5.83 3.74 6.87 6.31 7.38

1.15 8.53 7.49 5.40 8.53 7.92 8.79

1.33 10.10 9.06 6.97 10.10 9.45 10.13

1.50 11.58 10.54 8.45 11.58 10.89 11.39

1.67 13.06 12.02 9.93 13.06 12.33 12.65

1.83 14.46 13.42 11.33 14.45 13.69 13.84

1.98 15.77 14.73 12.64 15.77 14.96 14.96

2.12 16.99 15.95 13.86 16.99 16.15 16.00

2.38 19.25 18.21 16.12 19.25 18.36 17.93

2.49 20.21 19.17 17.08 20.21 19.29 18.75

2.60 21.17 20.13 18.04 21.17 20.23 19.57

2.77 22.65 21.64 19.52 22.65 21.67 20.83

2.90 23.79 22.75 20.66 23.79 22.77 21.80

3.00 24.66 23.62 21.53 24.66 23.62 22.54

0

20

40

60

80

100

120

140

0 200 400 600 800

RP

M


100 GPM

150 GPM

200 GPM

250 GPM




39


Motor Size 4.75


Top Sub Box Up

3 1/2 IF 9900 - 10900 13423 - 14778

3 1/2 REG 9900 - 10900 13423 - 14778

Pin Down 3 15/16 ADHP 7000 9491


Box Down 3 15/16 ADHP 7000 9491


Pin Down 3 15/16 ADHP 7000 9491


Box Up 3 15/16 ADHP 7000 9491

Pin Down 3 15/16 ADHP 7000 9491


Box Down SA-LEFT HAND 5000 6779

Lower Seal Sub Pin Up SA-LEFT HAND 5000 6779

Bit Box Box Down

3 1/2 IF 9900 - 10900 13423 - 14778

3 1/2 REG 9900 - 10900 13423 - 14778




40

Fishing Diagram – 4-3/4 Inch Motor




41



Overall Length 279.75 inches ( 7.11 meters)


Common Box Connections 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-90, 4-1/2 X-Hole

Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)






Horsepower at Maximum Flow 148 HP (110.4 kW)



140,400 Lbs (624.5 kN) Dynamic 568.000 Lbs (2526.6 kN) Static 105,200 Lbs (467.9 kN) Dynamic 426,000 Lbs (1894.9 kN) Static



ABH Sleeve Recommended Make-Up Torque 25,000 Lbs-Ft (33,895 N-m)

Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 13,000 Lbs-Ft (17,626 N-m)

0

500

1000

1500

2000

2500

3000

0 200 400 600 800

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




42


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole

8-3/4” Hole 9-7/8” Hole 8-1/2” Hole 8-3/4” Hole 9-7/8” Hole

0.39 2.94 3.17 4.27

0.59 0.94 0.19 4.26 4.49 5.58

0.78 2.52 1.77 5.52 5.75 6.83

0.96 4.02 3.27 0.21 6.72 6.95 8.01

1.15 5.60 4.85 1.77 7.98 8.21 9.25

1.33 7.10 6.35 3.25 9.17 9.40 10.43

1.50 8.51 7.76 4.65 10.3 10.53 11.55

1.67 9.92 9.17 6.05 11.43 11.66 12.67

1.83 11.25 10.50 7.36 12.50 12.72 13.71

1.98 12.50 11.75 8.60 13.48 13.71 14.70

2.12 13.66 12.91 9.75 14.41 14.64 15.62

2.38 15.83 15.08 11.89 16.14 16.37 17.32

2.49 16.74 15.99 12.79 16.87 17.10 18.04

2.60 17.65 16.90 13.70 17.60 17.83 18.77

2.77 19.07 18.32 15.10 18.72 18.95 19.88

2.90 20.15 19.40 16.17 19.59 19.82 20.73

3.00 20.98 20.23 16.99 20.25 20.48 21.39

0

50

100

150

200

250

300

350

0 200 400 600 800

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




43






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)














0

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

0 200 400 600 800 1000 1200

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




44


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.29 2.46 3.19

0.59 0.72 0.10 3.44 3.60 4.33

0.78 2.02 1.04 4.53 4.69 5.41

0.96 3.26 2.64 0.11 5.56 5.72 6.44

1.15 4.56 3.94 1.4 6.65 6.81 7.52

1.33 5.79 5.17 2.62 7.68 7.85 8.54

1.50 6.96 6.34 3.78 8.66 8.82 9.51

1.67 8.13 7.51 4.94 9.64 9.79 10.48

1.83 9.22 8.60 6.02 10.55 10.71 11.39

1.98 10.25 9.63 7.04 11.42 11.57 12.24

2.12 11.21 10.59 8.00 12.22 12.37 13.04

2.38 13.00 12.38 9.76 13.71 13.87 14.52

2.49 13.75 13.13 10.51 14.34 14.50 15.15

2.60 14.51 13.89 11.26 14.97 15.13 15.77

2.77 15.67 15.05 12.42 15.95 16.10 16.74

2.90 16.56 15.94 13.30 16.70 16.85 17.48

3.00 17.25 16.63 13.98 17.27 17.42 18.05

0

50

100

150

200

250

300

350

0 200 400 600 800 1000 1200

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




45





Common Box Connections 4-1/2 Reg., 4-1/2 IF, 4-1/2 H-90. 4-1/2 X-Hole

Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)












0

500

1000

1500

2000

2500

3000

3500

4000

4500

0 100 200 300 400 500 600 700

Torq

ue

Lb

s-Ft





46


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.45 2.62 3.46

0.59 0.76 3.65 3.82 4.65

0.78 2.14 0.11 4.78 4.95 5.77

0.96 3.44 1.49 5.86 6.03 6.84

1.15 4.82 2.79 0.13 7.00 7.17 7.97

1.33 6.12 5.47 1.49 8.07 8.24 9.03

1.50 7.35 6.7 2.78 9.09 9.26 10.04

1.67 8.58 7.94 4.00 10.11 10.28 11.05

1.83 9.74 9.09 6.37 11.06. 11.23 12.00

1.98 10.83 10.18 7.44 11.96 12.13 12.88

2.12 11.84 11.19 8.45 12.80 12.97 13.71

2.38 13.72 13.07 10.31 14.35 14.52 15.26

2.49 14.52 13.87 11.10 15.01 15.18 15.91

2.60 15.31 14.66 11.89 15.67 15.84 16.56

2.77 16.54 15.89 13.11 16.68 16.85 17.57

2.90 17.49 16.84 14.04 17.46 17.63 18.34

3.00 18.21 17.56 14.76 18.06 18.23 18.93

0

50

100

150

200

250

0 100 200 300 400 500 600

RP

M

Flow Rate (GPM)




47






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)





Differential Pressure at Max. Operating Torque 946 PSI (6522 kPa) )


140,400 Lbs (624.5 kN) Dynamic 568.000 Lbs(2526.6 kN) Static 105,200 Lbs (467.9 kN) Dynamic 426,000 Lbs (1894.9 kN) Static





0

1000

2000

3000

4000

5000

6000

7000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft





48


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.20 2.33 3.05

0.59 0.68 .08 3.31 3.45 4.15

0.78 1.94 1.34 4.37 4.51 5.21

0.96 3.13 2.53 0.09 5.38 5.51 6.20

1.15 4.39 3.79 1.34 6.44 6.57 7.25

1.33 5.58 4.98 2.52 7.44 7.58 8.25

1.50 6.71 6.11 3.64 8.39 8.53 9.19

1.67 7.84 7.24 4.76 9.34 9.48 10.13

1.83 8.90 8.30 5.81 10.23 10.37 11.02

1.98 9.89 9.29 6.80 11.07 11.21 11.85

2.12 10.82 10.22 7.72 11.85 11.99 12.62

2.38 12.54 11.94 9.42 13.30 13.45 14.06

2.49 13.27 12.67 10.15 13.91 14.06 14.67

2.60 14.00 13.40 10.87 14.53 14.68 15.28

2.77 15.13 14.53 11.99 15.48 15.63 16.22

2.90 15.99 15.39 12.84 16.20 16.35 16.94

3.00 16.65 16.05 13.50 16.76 16.91 17.49

0

50

100

150

200

250

0 100 200 300 400 500 600

RP

M

Flow Rate - GPM




49






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)










Maximum Overpull (Re-Run) 284,000 Lbs(1263.3 kN) for 4:2 Configuration 426,000 Lbs (1894.9 kN) for 3:3 Configuration




0

1000

2000

3000

4000

5000

6000

7000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




50


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.43 2.58 3.40

0.59 0.75 0.11 3.62 3.77 4.58

0.78 2.11 1.47 4.74 4.90 5.70

0.96 3.40 2.76 0.13 5.81 5.97 6.75

1.15 4.76 4.12 1.48 6.94 7.09 7.87

1.33 6.05 5.41 2.75 8.00 8.16 8.93

1.50 7.27 6.63 3.96 9.01 9.17 9.93

1.67 8.49 7.85 5.17 10.02 10.18 10.93

1.83 9.63 8.99 6.30 10.97 11.13 11.87

1.98 10.71 10.07 7.36 11.85 12.02 12.75

2.12 11.71 11.07 8.36 12.68 12.85 13.58

2.38 13.57 12.93 10.20 14.23 14.39 15.10

2.49 14.36 13.72 10.98 14.88 15.04 15.75

2.60 15.15 14.51 11.76 15.53 15.70 16.40

2.77 16.36 15.72 12.97 16.54 16.71 17.40

2.90 17.29 16.65 13.89 17.31 17.48 18.16

3.00 18.01 17.37 14.60 17.90 18.07 18.75

0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800 1000

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




51

0

1000

2000

3000

4000

5000

6000

7000

8000

9000

0 500 1000 1500

Torq

ue

Lb

s-Ft


Min Flow

Max Flow






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)



RPM per Unit Flow @ No Load 0.29 Revs/Gallon (0.077 Revs/Gallon)




Horsepower at Minimum Flow 114.3 HP (85.2 KW)










52


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.03 2.17 2.78

0.59 0.62 0.06 3.09 3.23 3.83

0.78 1.80 1.24 4.10 4.24 4.83

0.96 2.92 2.36 0.07 5.06 5.19 5.78

1.15 4.11 3.55 1.24 6.07 6.20 6.78

1.33 5.23 4.67 2.36 7.03 7.16 7.73

1.50 6.29 5.73 3.41 7.93 8.06 8.63

1.67 7.35 6.79 4.46 8.83 8.96 9.53

1.83 8.35 7.79 5.45 9.68 9.81 10.37

1.98 9.28 8.72 6.38 10.48 10.61 11.16

2.12 10.15 9.59 7.25 11.22 11.35 11.90

2.38 11.78 11.22 8.85 12.61 12.73 13.27

2.49 12.46 11.90 9.53 13.19 13.31 13.85

2.60 13.15 12.59 10.22 13.77 13.90 14.43

2.77 14.21 13.65 11.27 14.68 14.80 15.33

2.90 15.02 14.46 12.07 15.37 15.49 16.01

3.00 15.64 15.08 12.69 15.90 16.02 16.54


0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800 1000 1200

RP

M


300 GPM

450 GPM

600 GPM




53





Bit Size 7-7/8 – 9-7/8” (200 mm – 250.8 mm)














0

1000

2000

3000

4000

5000

6000

0 100 200 300 400

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




54


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.94 3.17 4.27

0.59 0.94 0.19 4.26 4.49 5.58

0.78 2.52 1.77 5.52 5.75 6.83

0.96 4.02 3.27 0.21 6.72 6.95 8.01

1.15 5.60 4.85 1.77 7.98 8.21 9.25

1.33 7.10 6.35 3.25 9.17 9.40 10.43

1.50 8.51 7.76 4.65 10.3 10.53 11.55

1.67 9.92 9.17 6.05 11.43 11.66 12.67

1.83 11.25 10.50 7.36 12.49 12.72 13.71

1.98 12.50 11.75 8.60 13.48 13.71 14.70

2.12 13.66 12.91 9.75 14.41 14.64 15.62

2.38 15.83 15.08 11.89 16.14 16.37 17.32

2.49 16.74 15.99 12.79 16.87 17.10 18.04

2.60 17.65 16.90 13.70 17.60 17.83 18.77

2.77 19.07 18.32 15.10 18.72 18.95 19.88

2.90 20.15 19.40 16.17 19.59 19.82 20.73

3.00 20.98 20.23 16.99 20.25 20.48 21.39

0

20

40

60

80

100

120

0 100 200 300 400

RP

M


200 GPM

400 GPM

500 GPM

600 GPM




55






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)












ABH Sleeve Recommended Maker-Up Torque 25,000 Lbs-Ft (33,895 N-m)


0

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

0 200 400 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




56


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 3.28 3.53 4.82

0.59 1.08 0.25 4.68 4.94 6.21

0.78 2.79 1.97 6.02 6.27 7.53

0.96 4.41 3.59 0.26 7.28 7.54 8.78

1.15 6.13 5.30 1.96 8.61 8.87 10.10

1.33 7.75 6.93 3.56 9.88 10.14 11.35

1.50 9.28 8.46 5.08 11.07 11.33 12.53

1.67 10.81 9.99 6.60 12.26 12.52 13.71

1.83 12.25 11.44 8.02 13.89 13.65 14.82

1.98 13.61 12.79 9.36 14.44 14.70 15.86

2.12 14.87 14.05 10.61 15.42 15.69 16.84

2.38 17.21 16.40 12.93 17.25 17.51 18.64

2.49 18.20 17.39 13.91 18.02 18.29 19.41

2.60 19.19 18.38 14.89 18.79 19.06 20.17

2.77 20.73 19.92 16.41 19.99 20.25 21.35

2.90 21.90 21.09 17.57 20.90 21.17 22.26

3.00 22.80 21.99 18.46 21.60 21.87 22.95

0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800 1000

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




57






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)









140,400 Lbs (624.5 kN) Dynamic 568.000 Lbs(2526.6 kN) Static 105,200 Lbs (467.9 kN) Dynamic 426,000 Lbs (1894.9 kN) Static



ABH Sleeve Recommended Make Up Torque 25,000 Lbs-Ft (33,895 N-m)


0

1000

2000

3000

4000

5000

6000

7000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




58


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.49 2.66 3.39

0.59 0.77 0.13 3.69 3.86 4.69

0.78 2.16 1.51 4.83 5.00 5.82

0.96 3.47 2.83 0.13 5.91 6.08 6.89

1.15 7.41 4.21 1.50 7.06 7.23 8.02

1.33 6.17 5.52 2.80 8.14 8.31 9.10

1.50 7.41 6.76 4.03 9.16 9.33 10.11

1.67 8.65 8.00 5.26 10.18 10.35 11.12

1.83 9.82 9.16 6.41 11.14 11.31 12.08

1.98 10.91 10.26 7.50 12.04 12.22 12.97

2.12 11.93 11.28 8.51 12.89 13.06 13.81

2.38 13.83 13.17 10.39 14.45 14.62 15.35

2.49 14.63 13.97 11.18 15.11 15.28 16.01

2.60 15.43 14.78 11.98 15.77 15.94 16.67

2.77 16.67 16.01 13.21 16.80 16.97 17.68

2.90 17.62 16.96 14.15 17.58 17.75 18.45

3.00 18.35 17.69 14.87 18.18 18.35 19.05

0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800 1000

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




59






Bit Size 7-7/8” – 9-7/8” (200 mm – 250.8 mm)














0

1000

2000

3000

4000

5000

6000

7000

8000

0 200 400 600 800 1000 1200

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




60


Bend Angle (°)

SLICK STABILZED

8-1/2” Hole


0.39 2.03 2.17 2.78

0.59 0.62 0.06 3.09 3.23 3.83

0.78 1.80 1.24 4.10 4.24 4.83

0.96 2.92 2.36 0.07 5.06 5.19 5.78

1.15 4.11 3.55 1.24 6.07 6.20 6.78

1.33 5.23 4.67 2.36 7.03 7.16 7.73

1.50 6.29 5.73 3.41 7.93 8.06 8.63

1.67 7.35 6.79 4.46 8.83 8.96 9.53

1.83 8.35 7.79 5.45 9.68 9.81 10.37

1.98 9.28 8.72 6.38 10.48 10.61 11.16

2.12 10.15 9.59 7.25 11.22 11.35 11.90

2.38 11.78 11.22 8.85 12.61 12.73 13.27

2.49 12.46 11.90 9.53 13.19 13.31 13.85

2.60 13.15 12.59 10.22 13.77 13.90 14.43

2.77 14.21 13.65 11.27 14.68 14.80 15.33

2.90 15.02 14.46 12.07 15.37 15.49 16.01

3.00 15.64 15.08 12.69 15.90 16.02 16.54

0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800 1000 1200

RP

M


300 GPM

400 GPM

500 GPM

600 GPM




61


Motor Size 6.75


Top Sub Box Up

4 1/2 IF 32000 - 35000 43386 - 47454

4 1/2 REG 21600 - 23700 29286 - 32133

4 1/2 H-90 23000 - 25300 31184 - 34302

4 1/2 XH 22200 - 24400 30099 - 33082

Pin Down 5 1/2 ADHP 25000 33895


Box Down 5 1/2 ADHP 25000 33895


Pin Down 5 1/2 ADHP 25000 33895


Box Up 5 1/2 ADHP 25000 33895

Pin Down 5 1/2 ADHP 25000 33895



14000 18981


SA-LEFT HAND

14000 18981

Bit Box Box Down

4 1/2 IF 32000 - 35000 43386 - 47454

4 1/2 REG 21600 - 23700 29286 - 32133

4 1/2 H-90 23000 - 25300 31184 - 34302

4 1/2 XH 22200 - 24400 30099- 33082




62





63

8” Motor, 4/5 Lobe Configuration, 3.6 Stages



Bit-to-Bend 86 inches (2.18 meters)

Common Box Connections 6-5/8 Reg., 7 H-90

Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

500

1000

1500

2000

2500

3000

3500

4000

4500

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




64


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 2.86 .60 2.38 4.5

0.59 3.98 1.83 .60 3.75 5.71

0.78 5.04 3.00 2.44 5.04 6.85

0.96 6.04 4.11 4.18 6.27 7.93

1.15 7.10 5.28 0.90 6.02 7.57 9.08

1.33 8.11 6.38 2.43 7.57 8.80 10.16

1.50 9.06 7.43 3.88 9.4 9.96 11.18

1.67 10.01 8.48 5.33 11.04 11.12 12.20

1.83 10.90 9.46 6.69 12.59 12.21 13.16

1.98 11.74 10.38 7.97 14.04 13.24 14.07

2.12 12.52 11.25 9.16 15.39 14.19 14.91

2.38 13.98 12.84 11.38 17.91 15.97 16.47

2.49 14.59 13.52 12.31 18.97 16.72 17.13

2.60 15.21 14.20 13.25 20.03 17.47 17.79

2.77 16.16 15.24 14.70 21.68 18.63 18.82

2.90 16.88 16.04 15.81 22.93 19.52 19.60

3.00 17.44 16.66 16.66 23.90 20.2 20.20

0

50

100

150

200

250

0 100 200 300 400 500 600

RP

M


400 GPM

600 GPM

800 GPM

900 GPM




65






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

1000

2000

3000

4000

5000

6000

0 200 400 600 800

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




66


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 0.96 1.92 2.65 3.46

0.59 2.14 0.76 3.03 3.70 4.52

0.78 3.27 1.89 4.08 4.69 5.52

0.96 4.33 2.95 5.08 5.64 6.47

1.15 5.46 4.08 1.09 6.14 6.63 7.48

1.33 6.52 5.14 2.15 7.14 7.58 8.42

1.50 7.53 6.15 3.16 8.08 8.47 9.32

1.67 8.54 7.16 4.17 9.02 9.36 10.22

1.83 9.48 8.10 5.12 9.91 10.20 11.06

1.98 10.37 8.99 6.00 10.75 10.99 11.85

2.12 11.20 9.82 6.83 11.52 11.72 12.59

2.38 12.74 11.36 8.38 12.97 13.09 13.97

2.49 13.39 12.,01 9.03 13.58 13.66 14.55

2.60 14.04 12.66 9.68 14.19 14.24 15.13

2.77 15.04 13.67 10.69 15.13 15.13 16.03

2.90 15.82 14.44 11.46 15.85 15.82 16.71

3.00 16.41 15.03 12.05 16.41 16.34 17.24

0

50

100

150

200

250

0 200 400 600 800

RP

M


400 GPM

600 GPM

800 GPM

900 GPM




67






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

500

1000

1500

2000

2500

3000

3500

4000

4500

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft





68


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 1.84 1.56 4.40 6.15

0.59 3.53 1.53 3.27 5.75 7.53

0.78 5.13 3.14 4.90 7.04 8.83

0.96 6.66 4.66 0.37 6.44 8.26 10.06

1.15 8.26 6.27 1.99 8.06 9.54 11.36

1.33 9.78 7.79 3.50 9.60 10.76 12.59

1.50 11.22 9.23 4.94 11.06 11.91 13.75

1.67 12.66 10.67 6.38 12.52 13.06 14.91

1.83 14.00 12.02 7.73 13.88 14.14 16.01

1.98 15.27 13.29 9.00 15.17 15.16 17.03

2.12 16.46 14.48 10.19 16.37 16.11 17.99

2.38 18.65 16.67 12.38 18.59 17.86 19.77

2.49 19.58 17.61 13.32 19.53 18.61 20.52

2.60 20.51 18.53 14.25 20.48 19.35 21.27

2.77 21.95 19.97 15.68 21.93 20.50 33.44

2.90 23.05 21.07 16.78 23.04 21.38 23.33

3.00 23.89 21.92 17.63 23.90 22.06 24.01

0

50

100

150

200

250

300

0 200 400 600 800 1000

RP

M

Flow Rtae - GPM




69






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)






Horsepower at Maximum Flow 244 HP (182 kW)

Horsepower at Minimum Flow 131 HP (97.7 kW)





ABH Sleeve Recommended make-Up Torque 40,000 Lbs-Ft (54,233 N-m)


0

1000

2000

3000

4000

5000

6000

7000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




70


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 2.86 .60 2.38 4.5

0.59 3.98 1.83 0.60 3.75 5.71

0.78 5.04 3.00 2.44 5.04 6.85

0.96 6.04 4.11 4.18 6.27 7.93

1.15 7.10 5.28 0.90 6.02 7.57 9.08

1.33 8.11 6.38 2.43 7.57 8.80 10.16

1.50 9.06 7.43 3.88 9.4 9.96 11.18

1.67 10.01 8.48 5.33 11.04 11.12 12.20

1.83 10.90 9.46 6.69 12.59 12.21 13.16

1.98 11.74 10.38 7.97 14.04 13.24 14.07

2.12 12.52 11.25 9.16 15.39 14.19 14.91

2.38 13.98 12.84 11.38 17.91 15.97 16.47

2.49 14.59 13.52 12.31 18.97 16.72 17.13

2.60 15.21 14.20 13.25 20.03 17.47 17.79

2.77 16.16 15.24 14.70 21.68 18.63 18.82

2.90 16.88 16.04 15.81 22.93 19.52 19.60

3.00 17.44 16.66 16.66 23.90 20.2 20.20

0

50

100

150

200

250

300

0 200 400 600 800 1000

RP

M

Differential Presssure - PSI

Series1

Series2

Series3




71






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

1000

2000

3000

4000

5000

6000

7000

8000

9000

0 200 400 600 800

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




72


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 1.14 1.99 2.86 3.80

0.59 2.38 0.85 3.17 3.96 4.90

0.78 3.56 2.04 4.29 5.00 5.95

0.96 4.68 3.17 5.34 5.99 6.95

1.15 5.86 4.36 1.19 6.46 7.04 8.00

1.33 6.97 5.49 2.32 7.52 8.03 8.99

1.50 8.03 6.56 3.39 8.52 8.96 9.93

1.67 9.09 7.63 4.46 9.52 9.89 10.87

1.83 10.08 8.63 5.46 10.46 10.77 11.75

1.98 11.01 9.57 6.40 11.34 11.60 12.58

2.12 11.88 10.45 7.28 12.17 12.37 13.36

2.38 13.49 12.09 8.92 13.69 13.79 14.79

2.49 14.17 12.78 9.61 14.34 14.40 15.40

2.60 14.86 13.47 10.30 14.99 15.00 16.01

2.77 15.91 14.53 11.37 15.99 15.94 16.95

2.90 16.72 15.35 12.18 16.75 16.65 17.67

3.00 17.34 15.98 12.81 17.34 17.20 18.22

0

20

40

60

80

100

120

140

160

180

0 200 400 600 800

RP

M


300 GPM

500 GPM

700 GPM

900 GPM




73






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

2000

4000

6000

8000

10000

12000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




74


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 0.87 1.90 2.46 3.19

0.59 1.99 0.69 2.94 3.46 4.20

0.78 3.06 1.76 3.93 4.42 5.16

0.96 4.07 2.77 4.87 5.32 6.06

1.15 5.13 3.83 1.01 5.86 6.27 7.02

1.33 6.14 4.84 2.02 6.79 7.18 7.93

1.50 7.09 5.79 2.97 7.68 8.03 8.79

1.67 8.04 6.74 3.92 8.57 8.88 9.65

1.83 8.94 7.64 4.82 9.40 9.69 10.45

1.98 9.78 8.48 5.66 10.18 10.44 11.21

2.12 10.56 9.26 6.44 10.91 11.14 11.92

2.38 12.08 10.72 7.90 12.26 12.45 13.23

2.49 12.63 11.33 8.51 12.83 13.00 13.79

2.60 13.25 11.95 9.13 13.41 13.55 14.34

2.77 14.20 12.90 10.08 14.29 14.41 15.20

2.90 14.93 13.63 10.81 14.97 15.06 15.86

3.00 15.49 14.19 11.37 15.49 15.56 16.36

0

20

40

60

80

100

120

140

160

180

0 200 400 600 800 1000

RP

M


300 GPM

500 GPM

700 GPM

900 GPM




75






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)














0

1000

2000

3000

4000

5000

6000

7000

8000

9000

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




76


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 2.86 .60 2.38 4.5

0.59 3.98 1.83 .60 3.75 5.71

0.78 5.04 3.00 2.44 5.04 6.85

0.96 6.04 4.11 4.18 6.27 7.93

1.15 7.10 5.28 0.90 6.02 7.57 9.08

1.33 8.11 6.38 2.43 7.57 8.80 10.16

1.50 9.06 7.43 3.88 9.4 9.96 11.18

1.67 10.01 8.48 5.33 11.04 11.12 12.20

1.83 10.90 9.46 6.69 12.59 12.21 13.16

1.98 11.74 10.38 7.97 14.04 13.24 14.07

2.12 12.52 11.25 9.16 15.39 14.19 14.91

2.38 13.98 12.84 11.38 17.91 15.97 16.47

2.49 14.59 13.52 12.31 18.97 16.72 17.13

2.60 15.21 14.20 13.25 20.03 17.47 17.79

2.77 16.16 15.24 14.70 21.68 18.63 18.82

2.90 16.88 16.04 15.81 22.93 19.52 19.60

3.00 17.44 16.66 16.66 23.90 20.20 20.20

0

20

40

60

80

100

120

140

160

0 100 200 300 400 500 600

RP

M


300 GPM

500 GPM

700 GPM

900 GPM




77






Bit Size 9-1/2” – 12-1/4” (241.3 mm – 311.2 mm)




Maximum Operating Torque 9,358 Lbs-Ft (12,688 N-m)



Horsepower at Minimum Flow 63 HP (47 KW)


242,400 Lbs (1078.2 kN) Dynamic 988,000 Lbs (4394.8 kN) Static 494,000 Lbs (2197.4 kN) Dynamic 741,000 Lbs 3296.1 kN) Static





0

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

0 200 400 600 800

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




78


Bend Angle (°)

SLICK STABILZED

9-7/8” Hole

10-5/8” Hole

12-1/4” Hole

9-7/8” Hole 10-5/8” Hole

12-1/4” Hole

0.39 1.56 2.43 2.86 3.76

0.59 2.72 0.84 3.52 3.95 4.86

0.78 3.82 2.02 4.56 4.99 5.91

0.96 4.86 3.15 5.54 5.97 6.90

1.15 5.96 4.33 1.18 6.57 7.01 7.94

1.33 7.00 5.46 2.31 7.55 7.99 8.93

1.50 7.98 6.52 3.37 8.48 8.92 9.87

1.67 8.96 7.58 4.43 9.41 9.85 10.81

1.83 9.89 8.58 5.43 10.28 10.72 11.69

1.98 10.75 9.52 6.37 11.09 11.54 12.51

2.12 11.56 10.39 7.24 11.86 12.31 13.28

2.38 13.07 12.02 8.87 13.27 13.72 14.72

2.49 13.70 12.70 9.55 13.87 14.33 15.32

2.60 14.34 13.39 10.24 14.47 14.93 15.93

2.77 15.32 14.45 11.30 15.40 15.85 16.86

2.90 16.07 15.27 12.11 16.11 16.56 17.58

3.00 16.65 15.89 12.74 16.65 17.11 18.13

0

20

40

60

80

100

120

140

160

0 200 400 600 800

RP

M


300 GPM

500 GPM

700 GPM

900 GPM




79

8” Motor Tool Joint Torque Specifications

Motor Size 8.00


Top Sub Box Up

6 5/8 REG 53000 - 58000 71858 - 78637

7 H-90 53000 - 58000 71858 - 78637

Pin Down 6 1/2 ADHP 40000 54233


Box Down 6 1/2 ADHP 40000 54233


Pin Down 6 1/2 ADHP 40000 54233


Box Up 6 1/2 ADHP 40000 54233

Pin Down 6 1/2 ADHP 40000 54233



22000 29828


SA-LEFT HAND

22000 29828

Bit Box Box Down

6 5/8 REG 53000 - 58000 71858 - 78637

7 H-90 53000 - 58000 71858 - 78637




80

Fishing Diagram – 8 Inch Motor




81





Common Box Connections 6-5/8 Reg., 7-5/8 Reg., 7 H-90

Bit Size 11-1/4” – 26” (285.75 mm – 660.4 mm)




Maximum Operating Torque 8,850 Lbs-Ft (11,999 N-m)



Horsepower at Minimum Flow 72 HP (53.7 kW)


323,000 Lbs (1436.8 kN) Dynamic 1,260.000 Lbs (5604.8 kN) Static 242,700 Lbs (1079.6 kN) Dynamic 945,000 Lbs (4203.6 kN) Static

Maximum Overpull (Re-Run) 630,000 Lbs (2802.4 kN) for 4:2 Configuration 945,000 Lbs (4203,6 kN) for 3:3 Configuration

Motor Yield 1,300,000 Lbs (5782.7)


Near-Bit Stabilizer/Slick Sleeve Make-Up Torque 55.000 Lbs-Ft (74,570 N-m)

0

20

40

60

80

100

120

140

0 100 200 300 400 500 600

RP

M


600 GPM

900 GPM

1200 GPM




82


Bend Angle (°)

SLICK STABILZED

12-1/4” Hole

16” Hole 17-1/2” Hole

12-1/4” Hole

16” Hole 17-1/2” Hole

0.39 0.63 4.67 5.89 6.90

0.59 2.02 5.75 7.00 8.01

0.78 3.34 6.78 8.06 9.07

0.96 4.60 7.75 9.05 10.06

1.15 5.92 8.78 10.11 11.12

1.33 7.17 0.38 9.75 11.11 12.11

1.50 8.35 1.56 10.67 12.05 13.06

1.67 9.53 2.74 0.04 11.59 12.99 14.00

1.83 10.64 3.85 1.15 12.45 13.88 14.89

1.98 11.69 4.90 2.19 13.26 14.71 15.72

2.12 12.66 5.87 3.16 14.02 15.49 16.50

2.38 14.47 7.67 4.97 15.43 16.93 17.94

2.49 15.23 8.44 5.74 16.02 17.54 18.55

2.60 16.00 9.21 6.50 16.62 18.15 19.16

2.77 17.18 10.39 7.68 17.53 19.09 20.10

2.90 18.08 11.29 8.59 18.24 19.82 20.83

3.00 18.78 11.99 9.28 18.78 20.37 21.38

0

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft


600 GPM

1200 GPM




83






Bit Size 11-1/4” – 26” (285.75 mm – 660.4 mm)




Maximum Operating Torque 11,250 Lbs-Ft (15253 N-m)



Horsepower at Minimum Flow 110 HP (82 KW)




Motor Yield 1,300,000 Lbs (5782.7 kN)



0

2000

4000

6000

8000

10000

12000

0 200 400 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




84


Bend Angle (°)

SLICK STABILZED

12-1/4” Hole

16” Hole 17-1/2” Hole

12-1/4” Hole

16” Hole 17-1/2” Hole

0.39 0.41 3.75 4.67 5.43

0.59 1.63 4.71 5.68 6.44

0.78 2.78 5.62 6.63 7.39

0.96 3.88 6.49 7.54 8.30

1.15 5.03 7.40 8.49 9.25

1.33 6.13 0.20 8.26 9.40 10.16

1.50 7.16 1.23 9.08 10.25 11.01

1.67 8.20 2.26 9.90 11.10 11.86

1.83 9.17 3.23 0.86 10.66 11.91 12.67

1.98 10.08 4.15 1.78 11.38 12.66 13.42

2.12 10.93 5.00 2.63 12.06 13.37 14.13

2.38 12.51 6.57 4.20 13.30 14.67 15.43

2.49 13.18 7.24 4.87 13.83 15.23 15.99

2.60 13.85 7.91 5.54 14.36 15.78 16.54

2.77 14.88 8.94 6.57 15.18 16.63 17.39

2.90 15.67 9.73 7.36 15.80 17.29 18.05

3.00 16.28 10.34 7.97 16.28 17.79 18.55

0

20

40

60

80

100

120

140

0 200 400 600 800

RP

M


600 GPM

900 GPM

1200 GPM




85






Bit Size 11-1/4” – 26” (285.75 mm – 660.4 mm)














0

2000

4000

6000

8000

10000

12000

14000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




86


Bend Angle (°)

SLICK STABILZED

12-1/4” Hole

16” Hole 17-1/2” Hole

12-1/4” Hole

16” Hole 17-1/2” Hole

0.39 0.49 4.07 5.10 5.95

0.59 1.77 5.08 6.14 6.99

0.78 2.98 6.03 7.14 7.99

0.96 4.13 6.94 8.08 8.93

1.15 5.35 7.89 9.07 9.92

1.33 6.50 0.26 8.80 10.01 10.86

1.50 7.59 1.35 9.65 10.90 11.75

1.67 8.68 2.44 10.50 11.79 12.64

1.83 9.70 3.46 0.97 11.31 12.62 13.47

1.98 10.66 4.42 1.93 12.06 13.41 14.26

2.12 11.56 5.31 2.82 12.77 14.14 14.99

2.38 13.22 6.98 4.49 14.07 15.50 16.35

2.49 13.93 7.68 5.19 14.63 16.07 16.92

2.60 14.63 8.38 5.89 15.18 16.65 17.50

2.77 15.72 9.47 6.98 16.03 17.54 18.39

2.90 16.55 10.30 7.81 16.69 18.22 19.07

3.00 17.19 10.94 8.45 17.19 18.74 19.59

0

20

40

60

80

100

120

140

160

180

0 200 400 600 800 1000

RP

M


600 GPM

800 GPM

1000 GPM

1200 GPM




87




Common Box Connections 6-5/8 reg., 7-5/8 Reg., 7 H-90

Bit Size 11-1/4” – 26” (285.75 mm – 660.4 mm)














0

2000

4000

6000

8000

10000

12000

14000

16000

18000

0 200 400 600 800 1000 1200

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




88


Bend Angle (°)

SLICK STABILZED

12-1/4” Hole

16” Hole 17-1/2” Hole

12-1/4” Hole

16” Hole 17-1/2” Hole

0.39 0.35 3.97 4.27 4.95

0.59 1.50 4.84 5.23 5.91

0.78 2.59 5.67 6.15 6.83

0.96 3.63 6.46 7.02 7.70

1.15 4.72 2.29 7.93 8.61

1.33 5.76 0.15 8.08 8.80 9.48

1.50 6.74 1.13 8.82 9.62 10.3

1.67 7.72 2.11 9.56 10.44 11.11

1.83 8.64 3.03 0.78 10.26 11.21 11.89

1.98 9.50 3.89 1.65 10.92 11.93 12.61

2.12 10.31 4.70 2.45 11.53 12.61 13.29

2.38 11.81 6.19 3.95 12.67 13.86 14.54

2.49 12.44 6.83 4.58 13.15 14.39 15.07

2.60 13.08 7.46 5.21 13.63 14.92 15.60

2.77 14.06 8.44 6.19 14.37 15.74 16.42

2.90 14.80 9.18 6.94 14.94 16.37 17.05

3.00 15.38 9.76 7.51 15.38 16.85 17.53

0

20

40

60

80

100

120

140

160

180

0 200 400 600 800 1000 1200

RP

M


600 GPM

800 GPM

1000 GPM

1200 GPM




89


motor Size

9.63


Top Sub Box Up

7 5/8 REG 83000 - 91000 112533-123379

6 5/8 REG 53000 - 58000 71858 - 78637

7 H-90 53000 - 58000 71858 - 78637

Pin Down 8 1/16 ADHP 60000 81349


Box Down 8 1/16 ADHP 60000 81349


Pin Down 8 1/16 ADHP 60000 81349

Adjustable Bend Housing Sub-Assembly Box Up 8 1/16 ADHP 60000 81349

Pin Down 8 1/16 ADHP 60000 81349



48000 65079


SA-LEFT HAND

48000 65079

Bit Box Box Down

7 5/8 REG 83000 - 91000 112533-123379

6 5/8 REG 53000 - 58000 71858 -78637

7 H-90 53000 - 58000 71858 - 78637




90





91




Common Box Connections 7-5/8 Reg., 8-5/8 Reg

Bit Size 14-3/4” – 26” (374.65 mm – 660.4 mm)






Horsepower at Maximum Flow 529 HP ( 394.5 KW)


Maximum Weight-on-Bit 4:2 Bearing Configuration

484,000 Lbs (2152.9 kN) Dynamic 2,052,000 Lbs (9127.8 kN) Static

Maximum Overpull (Re-Run) 1,026,000 Lbs (4563.9 kN) for 4:2 Configuration

Motor Yield 2,500,000 Lbs (11,120.5 kN)



0

5000

10000

15000

20000

0 200 400 600 800 1000

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




92

Bend Angle (°)

SLICK STABILZED

16” Hole 17-1/2” Hole 16” Hole 17-1/2” Hole

0.39 3.95 4.61

0.59 4.89 5.55

0.78 5.79 6.45

0.96 0.74 6.64 7.30

1.15 1.81 7.54 8.20

1.33 2.84 0.75 8.40 9.06

1.50 3.80 1.71 9.20 9.86

1.67 4.76 2.67 10.00 10.66

1.83 5.67 3.58 10.76 11.42

1.98 6.52 4.43 11.47 12.13

2.12 7.32 5.22 12.13 12.79

2.38 8.79 6.70 13.37 14.03

2.49 9.42 7.32 13.89 14.55

2.60 10.04 7.94 14.41 15.07

2.77 11.05 8.91 15.21 15.87

2.90 11.74 9.64 15.83 16.49

3.00 12.31 10.21 16.30 16.96

0

20

40

60

80

100

120

140

160

180

0 200 400 600 800 1000

RP

M


900 GPM

1200 GPM

1500 GPM

1800 GPM




93


Motor Size 11.25


Top Sub Box Up

7 5/8 REG 83000 - 91000 112527 - 123373

8 5/8 REG 134000 - 153000 181671 - 207430

Pin Down 9 11/16 ADHP 75000 101681


Box Down 9 11/16 ADHP 75000 101681


Pin Down 9 11/16 ADHP 75000 101681


Box Up 9 11/16 ADHP 75000 101681

Pin Down 9 11/16 ADHP 75000 101681




Bit Box Box Down

7 5/8 REG 83000 - 91000 112527 –

123373

8 5/8 REG 134000 - 153000 181671 - 207430




94





95

COILED TUBING MOTORS

1-11/16”, 5/6 Lobe Configuration, 2.3 Stages

Lobe Configuration 5/6 Lobe – 2.3 Stages


Common Box Connections NC12, AW Rod, 1-1/4 Reg, 1-1/4 AMMT

Bit Size 1-7/8” – 2-3/4” (47.63 mm – 69.9mm)

Maximum Flow Rate 40 GPM (151.4 LPM)

Minimum Flow Rate 20 GPM (75.7 LPM)

RPM per Unit Flow @ No Load 9.25 Rev/Gallon (2.44 Rev/Liter)

Maximum Operating Torque 80 Lbs-Ft (108.5 N-m)

Differential Pressure at Max. Operating Torque 270 PSI (1861.6 kPa)


Maximum Weight-on-Bit

8,360 Lbs (37,187 N) Dynamic 21,600 Lbs (96,082 N) Static

Maximum Overpull (Re-Run) 10.800 Lbs (48,041 N)

Motor Yield 15,000 Lbs (66,723 N)

0

10

20

30

40

50

60

70

80

90

0 50 100 150 200 250 300

Torq

ue

Lb

s-Ft





96

0

50

100

150

200

250

300

350

400

0 50 100 150 200 250 300

RP

M


20 GPM

30 GPM

40 GPM




97





Bit Size 1-7/8” – 2-3/4” (47.63 mm – 69.9mm)

Maximum Flow Rate 40 GPM (151.4 LPM)

Minimum Flow Rate 20 GPM (75.7 LPM)

RPM per Unit Flow @ No Load 15.42 Rev/Gallon (4.07 Rev/Liter)

Maximum Operating Torque 28.5 Lbs-Ft (38.64 N-m)







0

5

10

15

20

25

30

0 50 100 150 200

Torq

ue

Lb

s-Ft





98

0

100

200

300

400

500

600

700

0 50 100 150 200

RP

M


20 GPM

30 GPM

40 GPM




99





Bit Size 1-7/8” – 2-3/4” (47.63 mm – 69.9mm)

Maximum Flow Rate 55 GPM

Minimum Flow Rate 25 GPM

RPM per Unit Flow @ No Load 11 Rev. Gallon (2.91 Rev/Liter)

Maximum Operating Torque 180 Lbs-Ft (244.0 N-m)


Horsepower at Maximum Flow 33 HP (25 kW)





0

20

40

60

80

100

120

140

160

180

200

0 200 400 600 800

Torq

ue

Lb

s-Ft


Series1




100

0

100

200

300

400

500

600

700

0 200 400 600 800

RP

M


25 GPM

40 GPM

55 GPM




101


Motor Size 1.69


Top Sub Box Up

NC 12 400 542

1 1/4 REG 400 542

AW ROD 750 1017

1 1/4 AMMT 400 542

Pin Down 1 11/16 ADHP 250 339


Box Down 1 11/16 ADHP 250 339


Pin Down 1 11/16 ADHP 250 339


Box Up NA NA NA

Pin Down NA NA NA




Bit Box Box Down

NC 12 400 542

1 1/4 REG 400 542

AW ROD 750 1017

1 1/4 AMMT 400 542




102





103

2-3/8” MOTOR, 5/6 Lobe Configuration, 2.5 Stages



Common Box Connections NC16, BW Rod, 1-1/2 Reg, 1-1/2 AMMT

Bit Size 2-1/2” – 3-1/4” (63.5 mm – 82.6 mm)


Minimum Flow Rate 20 GPM ( 76 LPM)






12,140 Lbs (54.0 kN) Dynamic 35,000 Lbs (155.7 kN) Static

Maximum Overpull (Re-Run) 17,500 Lbs (77.8 kN


0

20

40

60

80

100

120

140

160

180

0 50 100 150 200 250 300 350 400

Torq

ue

Lb

s-Ft





104

0

50

100

150

200

250

300

350

400

0 100 200 300 400

RP

M


20 GPM

35 GPM

50 GPM




105


Motor Size 2.38


Top Sub Box Up

NC 16 750 1017

1 1/2 Reg 750 1017

BW ROD 1000 1356

1 1/2 AMMT 750 1017

Pin Down 2 3/8 ADHP 1000 1356


Box Down 2 3/8 ADHP 1000 1356


Pin Down 2 3/8 ADHP 1000 1356


Box Up NA NA NA

Pin Down NA NA NA




Bit Box Box Down

NC 16 750 1017

1 1/2 Reg 750 1017

BW ROD 1000 1356

1 1/2 AMMT 750 1017




106





107

2-7/8” 5/6 Lobe Configuration, 3.3 Stages


Overall Length 60” Stator

Common Box Connections 2-3/8 Reg., NW Rod

Bit Size 3-1/2” – 4-1/2” (88.9 mm – 114.3 mm)

Maximum Flow Rate 80 GPM ( 303 LPM)

Minimum Flow Rate 20 GPM ( 76 LPM)





Horsepower at Minimum Flow 2.2 HP (1.64 kW)

Maximum Weight-on-Bit 19,340 Lbs (86 kN) Dynamic 61,600 Lbs (274 kN) Static

Maximum Overpull (Re-Run) 30.800 Lbs (137 kN)


0

20

40

60

80

100

120

140

160

180

200

0 100 200 300 400 500 600

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




108

0

50

100

150

200

250

300

350

400

450

500

0 100 200 300 400 500 600

RP

M


20 GPM

50 GPM

80 GPM




109

2-7/8” 5/6 Lobe Configuration, 7.0 Stages




Bit Size 3-1/2” – 4-1/2” (88.9 mm – 114.3 mm)





Horsepower at Maximum Flow 36 HP (26.85)


Maximum Overpull (Re-Run_ 30.800 Lbs (137 kN)


0

100

200

300

400

500

600

0 200 400 600 800 1000 1200

Torq

ue

(Lb

s-Ft





110

0

50

100

150

200

250

300

350

400

450

500

0 200 400 600 800 1000 1200

RP

M


20 GPM

50 GPM

80 GPM




111





Bit Size 3-1/2” – 4-1/2” (88.9 mm – 114.3 mm)







Horsepower at Minimum Flow 8.8 HP (6.56 kW)


Maximum Overpull (Re-Run) 30.800 Lbs (137 kN)


0

50

100

150

200

250

300

0 100 200 300 400 500

Torq

ue

Lb

s-Ft


Min Flow

Max Flow




112

0

50

100

150

200

250

300

350

400

0 100 200 300 400 500

RP

M


70 GPM

90 GPM

110 GPM




113


Motor Size 2.88

Thread Torque Lbs-FT Torque N-m

Top Sub Box Up

2 3/8 REG 2000 - 2500 2712 - 3389

NW ROD 2200 - 2700 2983 - 3661

Pin Down 2 7/8 ADHP 1300 1762


Box Down 2 7/8 ADHP 1300 1762


Pin Down 2 7/8 ADHP 1300 1762


Box Up NA NA NA

Pin Down NA NA NA




Bit Box Box Down

2 3/8 REG 2000 - 2500 2712 - 3389

NW ROD 2200 - 2700 2983 - 3661




114





115

Useful Conversion Factors

Length:

1 Foot = 12 Inches

1 inch = 0.0833 Feet

1 Inch = 2.54 centimeters = 25.4 millimeters

100 centimeters = 1000 millimeters = 1 Meter

1 Meter = 3.280834 Feet

1 Foot = 0.3048 Meters

Volume:

1 Oil Barrel = 42 Gallons

1 Oil Barrel = 158.97 Liters

1 Gallon = 0.02381 Oil Barrels

1 Liter = 0.00629 Oil Barrels

1 Gallon = 3.785 Liters

1 Liter = 0.26417 Gallons

Force:

1 Pound Force = 4.44822 Newton

1 Newton = 0.2248089 Pounds Force

Pressure:

1 Pound/Square Inch = 6.8947 kilo-Pascals

1 KPascal = 0.14504 Pound/Square Inch

Temperature:

° Celsius = (°Fahrenheit – 32)/1.8

° Fahrenheit = 1.8 x °Celsius + 32

Useful Formulas

Hydraulic Horsepower = Pressure

(psi) x Flow Rate (gpm)/1714

Mechanical Horsepower = Torque

(lbs-ft) x rpm/5252

Annular Velocity = 24.5 x

GPM/(Diameter Hole (inches)2 – OD

pipe (inches)2 )

Where: psi = pounds per square inch

gpm = gallons per minute

rpm = revolutions per minute

AXON Downhole Products 10608 Tower Oaks Blvd.Houston, TX 77070P 281.255.5545 F 281.255.5591

SDS Erbil FacilityGazna Rd.Ainkawa, ErbilKurdistan Region, IraqP 964 662 577 868

Quoz Industrial EstatePO Box 377586Dubai, UAEP 971 4 347 6665F 971 4 347 6625

AXON Energy ProductsWORLD HEADQUARTERS10343 Sam Houston Park Dr.Suite 210Houston, TX 77064P 832.581.4100F 281.890.8817

Visit axonep.comfor more information

drilling motor handbook - axon energy...

Documents