tfc guide_full catalog

2 TRIANGLE FASTENER CORPORATION800.486.1832 / www.trianglefastener.com

Visit our website for the m

ost up to date product and technical information!

We serve the fastening systems needs of the following core markets.Flat Roofing: Low Slope Roofing IndustryMetal Building: Metal Building, Metal Roofing and SidingDrywall: Commercial Steel Framing, Drywall, EIFS General Contracting: HVAC, Electrical, Mechanical

FASTENING SYSTEMS AND SOLUTIONS FOR FASTENING SYSTEMS AND SOLUTIONS FOR COMMERCIAL CONSTRUCTIONCOMMERCIAL CONSTRUCTION

Since 1977, Triangle Fastener Corporation has supplied the construction industry with the most comprehensive lines of standard and specialty fastening systems solutions. We are committed to offering the latest fastening systems technologies that provide high performance and low in-place costs.

But that’s only part of the story…

We offer local inventories and services that meet your performance and quality demands. Our “hands-on" approach to servicing your needs guarantees that you get the attention you deserve.

How Can We Help You?Contact us for your next construction fastening requirement!

Stop by our showroom and be serviced by our knowledgeable staff of fastening systems specialists. We offer a variety of products for metal, wood, concrete, and drywall applications.

With over 15,000 standard and specialty items in stock, we can ship most orders the same day! Our “Market Specific" programs guarantees that we’ll have the fastener you need. Our local delivery capabilities will get your order to the job site when you need it!

► Computerized Inventory Management ► Direct Sales Team ► Job Site Assistance ► Engineering Support ► Product Development ► Delivery program ► Inventory management programs

MARKETS SERVEDMARKETS SERVED

LOCATIONSLOCATIONS

SERVICESSERVICES




DISTRIBUTIONDISTRIBUTION23 locations are stocked full of standard and specialty fastening system solutions. Computerized inventory control allows immediate access from every location.

MARKET SPECIALISTSMARKET SPECIALISTSEach of our locations are supported by our direct sales staff geared to handle the market’s specific product and service requirements.

PRODUCT DESIGNPRODUCT DESIGNOur TFC Fastening System Design Center can custom design products to meet your application requirements.

TOOL REPAIRTOOL REPAIRWe don’t just sell tools, we fix them too! Just bring them to the branch and we will have them serviced in no time flat!

PRODUCT RESEARCHPRODUCT RESEARCHThe products we offer meet or exceed industry standards. We can also provide additional research to fit your specific needs.

From the time we pick up the phone to long after the product is used, we are here to help you!

We provide the most innovative products, superior service, and a focused approach to your specific requirements. Our commitment to developing quality products and programs assure easy installation at low cost.

“TFC SPECIFIC"Products and ProgramsTFC SPECIFIC™ products are designed by and offered exclusively from TFC. They provide higher performance than products that are typically used.

► BLAZER® High Performance Drill Screws ► BRACER® Bracing System Washers ► BUTYL TAPE-SEAL™ Butyl Tape ► CONCEALOR® Low Profile Head Fastener ► GET-A-GRIP™ In-Stock Painted Rivets ► KALIDA-KOTE™ Paint For Fasteners, Rivets, Closures ► NEED-IT-NOW!™ Market Specific Product Program ► PANEL-TITE® Metal to Wood Fasteners ► PIPE-MASTER® Metal Roofing Pipe Flashing ► PAK-ONE™ Job Pack Program ► SENTRY PLUS FIVE® High Performance Roofing Screws ► STRESS-LESS® Stress Reducing Fastener ► STRESS-LOK® Load Distributing Washer ► SD300™ 304 Stainless Steel Drill Screws ► TFC 100/116™ Polyurethane Tube Sealant ► TRACER® High Performance Drywall Screws ► TWISTER® Pre-tied Wire ► ULP™ Ultra Low Profile Fasteners ► VRT® Vibration Resistant Thread Technology

With every product we supply, you'll get the most comprehensive support programs.

“TFCProdTFC Sdesigexclprothaty

®

For the most updated product information and For the most updated product information and access to all of our TFC SPECIFIC Catalogs access to all of our TFC SPECIFIC Catalogs visit our website www.trianglefastener.com.visit our website www.trianglefastener.com.

CONSTRUCT BETTER, FASTER CONSTRUCT BETTER, FASTER & LESS COSTLY& LESS COSTLY



ost up-to-date product and technical information!

TABLE OF CONTENTS - A TO H TABLE OF CONTENTS - A TO H

AA

BB

CCDD

EE

FF

GGHH

Abrasive Saw Wheels and Grinding 230-233Access Doors . . . . . . . . . . . . . . . . . 282-284Accuseam . . . . . . . . . . . . . . . . . . . . . . . . .58AccuTrac . . . . . . . . . . . . . . . . . . . . . . . . . .58Acoustical Tie Wires . . . . . . . . . . . . . . . .106ACQ Treated Lumber . . . . . . . . . . . . . . .301Adhesives - Spray . . . . . . . . . . . . . . . . . . .74ANCHORS Light & Medium Duty Expansion . . . . . . . . . . . . . . 112,116,117 E-Z ANCHOR . . . . . . . . . . . . . . 110-111 Fiber Plug . . . . . . . . . . . . . . . . . 113,195 Lead . . . . . . . . . . . . . . . . . . . . . . 113,195 LEGS Brand . . . . . . . . . . . . . . . . . . . 117 Plastic . . . . . . . . . . . . . . . . . 112-113,116 Plastic Drive Pin . . . . . . . . . . . . . . . .194 Strap Toggle. . . . . . . . . . . . . . . . . . . . 119 TOGGLE . . . . . . . . . . . . . . . . . . . . . . 116 WALL DOG . . . . . . . . . . . . . . . . 114-115 ZIP-TOGGLE . . . . . . . . . . . . . . . . . . . 118 Anchor Bolts . . . . . . . . . . . . . . . . . . . . . .137Arrow Staplers . . . . . . . . . . . . . . . . . . . . . .52

BACKER-ON Screws . . . . . . . . . . . . . . . .85Base Lock . . . . . . . . . . . . . . . . . . . . . . . . .71BASE PLY Fastening Patterns . . . . . . . . . . . 62, 63, 65, 67, 69BASE Sheet FM90, FM75, FM260, FM290,

TWINLOK, LOC-NAIL . . . . . . . . . . . 60-69Batten Strip . . . . . . . . . . . . . . . . . . . . . . . .59Beam Clamps . . . . . . . . . . . . . . . . .130, 131Bit Holders . . . . . . . . . . . . . . . . . . . . . . . .241BLAZER® Self-Drilling Fasteners . . . . . 8-18Blind Rivets . . . . . . . . . . . . . . . . . . . . . . . .46B-Line Fasteners . . . . . . . . . . . . . . . 132-136Bolts Sizes . . . . . . . . . . . . . . . . . . . . .196, 197 Strengths . . . . . . . . . . . . . . . . . . 293-295Bonded Washer . . . . . . . . . . . . . . . . . . . .201Boring Bits . . . . . . . . . . . . . . . . . . . . . . . .235BOSCH . . . . . . . . . . . . . . . . . . . . . . . . . .210Boxes - Jobsite . . . . . . . . . . . . . . . . . . . .279BRACER® Hillside Washer . . . . . . 206-208Bridal Rings . . . . . . . . . . . . . . . . . . . . . . .136Bridge Deck Fastener . . . . . . . . . . . . . . . .24Brooms . . . . . . . . . . . . . . . . . . . . . . . . . .242Brushes - Paint / Rollers . . . . . . . . . . . . .242BUILDEX EZ Anchors . . . . . . . . . . . . . . . . 110, 111 Self-Drilling Fasteners . . . . . . . . . . 28-31 Bulb-Tite Rivets . . . . . . . . . . . . . . . . . . . . .49ButtonKap Nails . . . . . . . . . . . . . . . . . . . . .50Butyl Tape - Metal Panels . . . . . . . .266, 267

Cabinet Screws . . . . . . . . . . . . . . . . . .40, 41Cable Ties . . . . . . . . . . . . . . . . . . . . . . . .205Caddy - Beam Claps . . . . . . . . . . . . . . . .130Cap Head Fasteners . . . . . . . . . . . . . .15, 30Cap Nails - SIMPLEX . . . . . . . . . . . . .70, 71Cap Screws . . . . . . . . . . . . . . . . . . .196, 197Caps for Screw Tips - Rubber . . . . . . . . .205Capsule Anchors . . . . . . . . . . . . . . .184, 185Carriage Bolts . . . . . . . . . . . . . . . . . . . . .197Carts - Drywall . . . . . . . . . . . . . . . . . . . . .245Caulking Gun (Manual and Battery) . . . .264

Ceiling Clips . . . . . . 90, 101, 102, 106, 107, 124, 130, 131, 133-136Ceiling Clips - Powder Actuated . . . . . . . . . . 90, 101, 102Ceiling Clips - Tie Wire . . . . . . . . . . . . . .106Cement Board Screws . . . . . . . . . . . . . . .85Chalk Reel - Marking Tools and Refill . . .243Circular Saw Blades . . . . . . . . . . . .228, 229Clamps - Locking. . . . . . . . . . . . . . .238, 239Clip Screws (SSR) . . . . . . . . . . . . . . . . 20-23Clips - Powder Actuated . . . . . .90, 101, 102Closure Metal Panel / Foam . . . . . . . . . . . . . .255 UNIVERSAL CLOSURE . . . . . . . . . .257 VERSA VENT . . . . . . . . . . . . . . . . . .256Coil Nails . . . . . . . . . . . . . . . . . . . . . . . . . .51Collated Screws . . . . . . . . . . . . . . . . .44, 45Composite Deck . . . . . . . . . . . . . . . . . . . .39 CONCEALOR® Pancake Head . . . . . 20-23Concrete Fastening Systems Adhesives . . . . . . . . . . . . . . . . . 158-185 Code Compliant . . . . . . . . . . . . . . . . .154 Lightweight Anchors .113, 114, 194, 195 Overview of Products . . . . . . . .144, 145 Sawing & Coring Blades . . . . . .234, 235 Spike . . . . . . . . . . . . . . . . . . . . . 188-191 Threaded Anchors . . . . . . . . . . . 138-143 ZAMAC Drive Pin Anchor . . . . .192, 193Concrete Nails . . . . . . . . . . . . . . . . . . . . . .50Conduit Clips . . . . . 102, 125, 129, 132, 133Coolers - IGLOO . . . . . . . . . . . . . . . . . . .278Corrosion Information . . . . . . . . 18, 297-301Corrosion Resistant Screws

410 Stainless Steel . . . . . . . . . . . . . . . .10304 Stainless Steel Self Drill . . . . . . . . . 11304 Stainless Steel Self Tapper . . . . . . . . . . . . . . . . . . . . . . 34, 35, 38, 39, 86, 87TAPCON SS . . . . . . . . . . . . . . . . 138-141SENTRY PLUS FIVE® SS . . . . . . . . . .56Capped Head Screws . . . . . . . . . . .15, 30TRI-SEAL Coating . . . . . . . . . . . . . . . . .19Pancake Head Screws . . . . . . . . . . . . .20

Coupling Nuts . . . . . . . . . . . . . . . . . . . . .199Cutter Bits - Rotary . . . . . . . . . . . . . . . . .224

DEC-KING Exterior Wood Screws . . . . . .39Deck Screws Wood . . . . . . . . . . . . . . . . . . . . . . . . . .39 Metal . . . . . . . . . . . . . . . . . . . . . . . . . .25DEK-CAP - Metal Roofing End Cap Flashing . . . . . . . . . . . . . . . . . . . . . . .254DEKSTRIP . . . . . . . . . . . . . . . . . . . .252, 253DEWALT . . . . . . . . . . . . . . . . . . . . . . . . . 211Diamond Coring Bits - Concrete . . . . . . .235DIAMOND PRODUCTS . . . . . . . . . . . . .235Diamond Sawing Blades - Concrete 234, 235Dow INSTA-STICK, FROTHPAK, TILE BOND . . . . . . . . . . . . . . . . . . 74-78Drains - Roof . . . . . . . . . . . . . . . . . . . . . . .80Dril-Flex . . . . . . . . . . . . . . . . . . . . . . . .26, 27Drill Bit Carbide . . . . . . . . . . . . . . . . . . . 221-232 High Speed Steel . . . . . . . . . . . . . . . .220 Rebar Cutting . . . . . . . . . . . . . . . . . .224

SDS . . . . . . . . . . . . . . . . . . . . . . . . . .222 Sizes . . . . . . . . . . . . . . . . . . . . .218, 219 Spline . . . . . . . . . . . . . . . . . . . . . . . . .223 Wood Boring . . . . . . . . . . . . . . . 225-227Drills - Step . . . . . . . . . . . . . . . . . . . . . . .227Drill Screws HWH, Pan, Pancake, Countersunk . . . . . . . . . . . . . . . . . . 8-32Drive Pin Anchor (Zinc / Nylon) . . . . 192-194Drop-In Anchor . . . . . . . . . . . . . . . . 155-157Drywall Screws . . . . . . . . . . . . . . . . . . 81-83 Hollow Wall Anchors . . . . . . . . . 110-119 Technical Data . . . . . . . . . . . . . . . . . . .83Duck Bill Pliers . . . . . . . . . . . . . . . . . . . .238Ductile Drill Screws . . . . . . . . . . . . . . .26, 27DYNABOLT Sleeve Anchors . . . . . . 146-149

Ear Protection . . . . . . . . . . . . . . . . . . . . .278End Cap Flashing - Metal Roof Dek Caps . . . . . . . . . . . . . . . . . . . . .254EPCON Adhesive Anchoring Systems (A7, A6, G5, Umbrella, Screen, Capsules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158-187ES PRODUCTS . . . . . . . . . . . . . . . . . 62-69ET&F Pneumatic Tools . . . . . . . . . . . . . .216Explosion Venting Fasteners . . . . . . . . . . .33Extension Cords . . . . . . . . . . . . . . . . . . .215Extension Poles - Powder Actuated Tools . . 108, 109Eyebolts . . . . . . . . . . . . . . . . . . . . . . . . . .204EZ PRODUCTS - Anchors . . . . . . . 110, 111EZ Products - Drywall Hangers . . . . 110, 111

FABLOK Rivets . . . . . . . . . . . . . . . . . . . . .48Fall Protection . . . . . . . . . . . . . . . . .280, 281Fastener Properties . . . . . . . . . . . . 286-296 FEIN . . . . . . . . . . . . . . . . . . . . . . . . . . . .212FIBERPLUG . . . . . . . . . . . . . . . . . . . . . . 113Firestop . . . . . . . . . . . . . . . . . . . . . .270, 271First Aid Kits . . . . . . . . . . . . . . . . . . . . . .278Flashing - End Cap Metal Roof (DEK-CAP) . . . . . . . . . . . . . . . .254Flashing - Linear EPDM . . . . . . . . .252, 253Flat Roofing Fasteners . . . . . . . . . . . . 53-80Flat Washer . . . . . . . . . . . . . . . . . . . . . . .200Framing Screws . . . . . . . . . . . . . . . . . . . .84Framing Nailer . . . . . . . . . . . . . . . . . . .88, 89FROTH-PAK Spray Insulation . . . . . . .76, 77Furniture Screws . . . . . . . . . . . . . . . . .40, 41

Galvanizing Spray . . . . . . . . . . . . . . . . . .273Gas Charged Tool . . . . . . . . . . . . . . . . 88-95Globe - Beam Claps . . . . . . . . . . . . . . . .131Gloves . . . . . . . . . . . . . . . . . . . . . . . . . . .278Grinding Wheels . . . . . . . . . . . . . . .231, 233Grommet Seal Rivets . . . . . . . . . . . . . . . .49GYPFAST - Tools and Pins . . . . . . . 120-123

Hammers . . . . . . . . . . . . . . . . . . . . . . . . .242Hand Tools. . . . . . . . . . . . . . . . . . . .242, 243Hanger Studs . . . . . . . . . . . . . . . . . . . . .124Hard Hats . . . . . . . . . . . . . . . . . . . . . . . .278Heavy Gauge Drill Screws . . . 8, 10, 14, 22Hillside Washer . . . . . . . . . . . . . . . . . . . .206Hole Saw Kits . . . . . . . . . . . . . . . . . . . . .226

KB

Text Box

A-B-C-D-E-F-G-H-I-J-K-L-M-N-O-P-Q-R-S-T-U-V-W-X-Y-Z




TABLE OF CONTENTS - H TO STABLE OF CONTENTS - H TO S

II

KKLL

MM

NN

PPRR

SS

Hole Saws - Steel and Carbide . . . .225, 226Hole Sizes (Tapping Screws) . . . . . . . . .291

Ice and Water Shield . . . . . . . . . . . . . . . .265Insert Drive Bits . . . . . . . . . . . . . . . . . . . .241Installation Tool - Tie Wire . . . . . . . .108, 109INSTA-STICK Roofing Adhesive . . . . .74, 75Insulated Panel Screws . . . . . . . . . . . .21, 22Insulation Board (Rigid) Fasteners . . . . . . . . . . . . . . . 54-57 (Rigid) Plates . . . . . . . . . . . . . . . . . . . . .57Insulation Fasteners (Rigid) . . . . . . . . . . .29Inventory Management . . . . . . . . . . . . . .305

J-CLIP and J-MASTER Tools . . . . . . . . .107Jobsite Boxes . . . . . . . . . . . . . . . . . . . . .279

KALIDA-KOTE® Touch-Up Paint . . . . . .272Kesternich . . . . . . . . . . . . . . . . . . . . . . . .298KETT . . . . . . . . . . . . . . . . . . . . . . . . . . . .212Knives - Utility / CASE. . . . . . . . . . . . . . .244

LADD Overhead Fastening System . . . . .97Ladders . . . . . . . . . . . . . . . . . . . . . . . . . .245Lag Screws . . . . . . . . . . . . . . . . . . . . . . .202Lag Shield Insert . . . . . . . . . . . . . . . . . . . .43LAGMASTER Installation Tool . . . . . . . .109Lanyards . . . . . . . . . . . . . . . . . . . . . . . . .280Lasers . . . . . . . . . . . . . . . . . . . . . . . . . . .243Lead Concrete Anchors . . . . . . . . . . . . . .195Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117Levels . . . . . . . . . . . . . . . . . . . . . . . . . . .243Lifts - Drywall . . . . . . . . . . . . . . . . . . . . . .245Lightweight Deck Fasteners - Toggle Bolts / NTB/NC Fasteners. . . . . . . . . . . . .72, 73Loads - Powder Actuated . . . . . . . . . . . .103Locking Pliers - VICE GRIP . . . . . .238, 239Long-life Coating(TRI-SEAL) . . . . . . . . . .19Long Length Screws . . . . . . . . . . . . . . 54-57Low Profile Head Fasteners . . . . . . . . 20-23Low Slope Roofing Fasteners . . . . . . . . . .53

Machine Screws . . . . . . . . . . . . . . . . . . .203Magnetic Bit Holders . . . . . . . . . . . . . . . .241MAKITA . . . . . . . . . . . . . . . . . . . . . . . . . .213Marking Paint . . . . . . . . . . . . . . . . . . . . .273Master Flash . . . . . . . . . . . . . . . . . .250, 251Measuring Tapes . . . . . . . . . . . . . . . . . . .243Metal Abrasive Wheels . . . . . . . . . . . . 230-233 Steel Cutting Blades . . . . . . . . . . . . .229 Reciprocating Blades . . . . . . . . .236, 237Metal to Wood Fasteners (PANEL-TITE®) . . . . . . . . . . . . . . . 36-38METABO . . . . . . . . . . . . . . . . . . . . . . . . .213MILWAUKEE . . . . . . . . . . . . . . . . . . . . . .214Mounting Brackets - Conduit / Box / Rod and Wire / Strap . . . . . . . . . 132-136MULTI-SETT II Drop-In Anchors . . . 155-157

Nails Cap . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Collated . . . . . . . . . . . . . . . . . . . . . . . .51 Concrete . . . . . . . . . . . . . . . . . . . . . . .50 Hand Driven . . . . . . . . . . . . . . . . . . . .50 Insulation . . . . . . . . . . . . . . . . . . . .70, 71 Tension . . . . . . . . . . . . . . . . . . . . . . . .50Nail Base Screws . . . . . . . . . . . . . . . . . . .21Nailers - ET&F Heavy Steel Tool. . . . . . .216Nailers - Button Cap . . . . . . . . . . . . . . . . .50Nail Base Fasteners . . . . . . . . . . . 21, 60-61Nail-in Drive Pin Anchors . . . . . . . . . . . .194NC Fasteners . . . . . . . . . . . . . . . . . . . . . .72NEED-IT-NOW Program . . . . . . . . . . . . .304NPC SOLAR SEAL . . . . . . . . . . . . . . . . .259NTB Fasteners . . . . . . . . . . . . . . . . . . . . .72Nut Drivers - Hand . . . . . . . . . . . . . . . . .241Nuts Proof Loads . . . . . . . . . . . . . . . . . . . .296 Sizes . . . . . . . . . . . . . . . . . . . . .198, 199 Nutsetter . . . . . . . . . . . . . . . . . . . . . . . . .241

OLYBOND . . . . . . . . . . . . . . . . . . . . . . . . .79OMG (OLYBOND Roof Drains) . . . . . .79, 80

Pacecart (OLYBOND Installation) . . . . . . .79Paint KALIDA-KOTE® Touch-Up Paint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .272 Marking Spray . . . . . . . . . . . . . . . . . .273 Painted Fasteners . . . . . . . . . . . . . . .272PAK-ONE Program . . . . . . . . . . . . . . . . .305Pan American Fasteners . . . . . . . . . . .40, 41Pancake Head Fasteners . . . . . . . . . . 20-23PANEL-TITE® Post Frame Fasteners 36-38PEEL & SEAL . . . . . . . . . . . . . . . . . . . . .268Pins and Loads - Gas / Technical . . . . . . . . . 90-95, 104, 105Pins - Powder Actuated . . . . . . . . . . . 99-102Pins and Fuel - TRAKFAST . . . . . . . . 89-91Pipe Flashing PIPEMASTER® . . . . . . . . . . . .248, 249 Master Flash (35 year) . . . . . . .250, 251 Mini . . . . . . . . . . . . . . . . . . . . . . . . . .251 Multi-port . . . . . . . . . . . . . . . . . . . . . .251 Solar Flash . . . . . . . . . . . . . . . . . . . .251Plastic Cap Nails . . . . . . . . . . . . . . . . .50, 70Plastic Expansion Anchors . . . . . . . . . . . 116Plastic Light Duty Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110, 111, 112, 116Plates - Roofing / Insulation . . . . . . . . . . .57Platings / Coatings . . . . . . . . . . . . . . . . .300Platforms / Scaffolding . . . . . . . . . . . . . .245Plumb Bob - Laser . . . . . . . . . . . . . . . . .243Pneumatic Tools - ET&F . . . . . . . . . . . . .216Point Styles . . . . . . . . . . . . . . . . . . .289, 290 POLLY / Expansion Anchors . . . . . . . . . . 116Polymer Gypsum Fasteners / Tectum . . . .72POP TOGGLE Drywall Anchors . . . . . . . 116Post Frame Screws (PANEL-TITE®) . 36-39Powder Actuated Pins / Loads / Ceiling Clips . . . . . . . . . . . . . . . . 96-105Powder Actuated Tools Pins & Loads . . . . . . . . . . . . . . . . 99-103Power Cords . . . . . . . . . . . . . . . . . . . . . .215

Powered Bit . . . . . . . . . . . . . . . . . . . . . . .241 Power Point Pins . . . . . . . . . . . . . . . . 99-101Power Tools BOSCH . . . . . . . . . . . . . . . . . . . . . . .210 DEWALT . . . . . . . . . . . . . . . . . . . . . . 211 FEIN . . . . . . . . . . . . . . . . . . . . . . . . .212 KETT . . . . . . . . . . . . . . . . . . . . . . . . .212 MAKITA . . . . . . . . . . . . . . . . . . . . . . .213 METABO . . . . . . . . . . . . . . . . . . . . . .213 MILWAUKEE . . . . . . . . . . . . . . . . . . .214Powers Fastener . . . . . . . . . . . . . . . 114-119Pre-Tired Wires - TWISTER® . . . . . 106-109Pry Bars . . . . . . . . . . . . . . . . . . . . . . . . . .242Pullout Loads (Drill Screws) . . . . . . . . . . .17Pullover Loads . . . . . . . . . . . . . . . . . . . . . .16Purlin Clips . . . . . . . . . . . . . . . . . . . . . . .107

Quick Drive Fasteners and Tools . . . .44, 45

Ramset Trakfast . . . . . . . . . . . . . . . . . 88-95Ramset Powder Actuated . . . . . . . . . 96-105Rebar Cutting Bits . . . . . . . . . . . . . . . . . .224REDHEAD . . . . . . . . . . . . . . . . . . . . 146-157Reciprocating Saw Blades . . . . . . .236, 237REDI-BOLT Sleeve Anchors . . . . . .146, 147Respirators . . . . . . . . . . . . . . . . . . . . . . .278Retrofit Pipe Flashing . . . . . . . . . . . . . . .249Ridge Vent Closure . . . . . . . . . . . . . . . . .256Rivets Installation Tools . . . . . . . . . . . . . . . . .47 Blind . . . . . . . . . . . . . . . . . . . . . . . . . .46 BULB-TITE . . . . . . . . . . . . . . . . . . . . .49 FABLOK . . . . . . . . . . . . . . . . . . . . . . .48 GROMMET SEAL . . . . . . . . . . . . . . . .49 Painted . . . . . . . . . . . . . . . . . . . . . . . .46ROCK-ON Cement Board Fasteners . . . .85Rollers - Paint Rollers / Frames / Handles . . . . . . . . . . . . . . . . . . . . . . .242Roof Adhesive . . . . . . . . . . . . 74, 75, 78, 79Roof Drains . . . . . . . . . . . . . . . . . . . . . . . .80Roof Screw Plates . . . . . . . . . . . . . . . . . . .57Roof Venting - VERSA VENT . . . . . . . . .256Roofing Screws Built-up Roof . . . . . . . . . . . . . . . . . 54-57 Metal Roof . . . . . . . . . . . . . 14, 15, 20-23 Technical Data (BUR) . . . . . . . . . . 54-57 Technical Data (Metal) . . . . . . 16-19, 23Roofing Tools (BUR) AccuTrac / AccuSeam . . . . . . . . . . . . .58 Magnetic Driver (Lightweight) . . . . . . .61 PaceCart 2 . . . . . . . . . . . . . . . . . . . . .79

Safety Equipment - Roofers Kit . . . .278, 281Safety Glasses . . . . . . . . . . . . . . . . . . . .278Safety Harness . . . . . . . . . . . . . . . . . . . .281Salt Spray . . . . . . . . . . . . . . . . . . . . . . . .298SAMMY SUPER SCREWS . . . . . . . . . . .124Saw Blades Circular . . . . . . . . . . . . . . . . . . .228, 229 Reciprocating . . . . . . . . . . . . . .236, 237Scaffolding / Platforms . . . . . . . . . . . . . .245SCOTS Stainless Cap Head Fasteners . .30Screw Drivers . . . . . . . . . . . . . . . . . . . . .242Screw Driving Insert Bits . . . . . . . . . . . . .241

KB

Text Box





TABLE OF CONTENTS - S to ZTABLE OF CONTENTS - S to Z

SS

TTUUWW

ZZ

Screw Tip Caps . . . . . . . . . . . . . . . . . . . .205ScruBolt . . . . . . . . . . . . . . . . . . . . . . . . . . .33Sealants and Flashings . . . . . . . . . . 246-276Sealants NPC - Solar Seal . . . . . . . . . . . . . . .259 SIKA-Butyl, Polyurethane, Butyl Tape. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261

SCHNEE-MOREHEAD - Butyl,Silicone, Polyurethane . . . . . . . . . . . . . . . . . . .260 SONNEBORN - NP1 . . . . . . . . . . . . .259 SUREBOND - Adhesive, Siliconized Rubber . . . . . . . . . . . . . . . . . . . . . . .261 TFC100®,116® - Polyurethane . . . .258 TREMCO - Silicon, Polyurethane, Pourable . . . . . . . . . . . . . . . . . .262, 263 VULKEM 116 . . . . . . . . . . . . . . . . . . .263Security Screws . . . . . . . . . . . . . . . . . . . . .12 Self-Drilling Screws Carbon Screws . . . . . . . . . . 8-15, 20-23 Drywall Screws . . . . . . . . . . . . . . . . . .83 Framing Screws . . . . . . . . . . . . . . . . .84 Large Diameter Screws . . . . . . . . . . . .8 Pullout Loads . . . . . . . . . . . . . . . . . . .17 Screw Drive Screws . . . . . . . . . . . 20-22 Security Screws . . . . . . . . . . . . . . . . .12 Self-Sealing Screws . . . . . . . . . . . 12-15 Stainless Cap Head . . . . . . . . . . .15, 30 Stainless Steel Screws . . . . . .10, 11, 86 Technical Data . . . . . . . . . . . . . . . 16-19 VRT Technology . . . . . . . . . . . . . . . . .13 Washered . . . . . . . . . . . . . . . . . . .14, 15 Wood to Metal Screws . . . . . . . . . . . .10 Zinc Cap Head . . . . . . . . . . . .15, 30, 32SELF-TAPPING Carbon and Stainless Fasteners . . . . . . . . . . . . 33-42 Whole Sizes . . . . . . . . . . . . . . . . . . . .35SENCO Staplers . . . . . . . . . . . . . . . . . . . .52SENTRY PLUS FIVE® Roofing Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-57Sheet Metal Screws - HWH / Pan Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41, 42Sheet Metal Thickness . . . . . . . . . . . . . . .16Sheeting Screws . . . . . . . . . . . 13-15, 34-38Shovels . . . . . . . . . . . . . . . . . . . . . . . . . .242SIMPLEX Roofing Nails . . . . . . . . . . .70, 71SIPS Screws . . . . . . . . . . . . . . . . . . . . 60-61Sledge Hammers . . . . . . . . . . . . . . . . . . .242Sleeve Anchor . . . . . . . . . . . . . . . . . 146-149Snips - Hand . . . . . . . . . . . . . . . . . . . . . 240Sockets - Impact and Standard . . . . . . . 242SPAN-MASTER Steel Deck Screw . . . . . 24SPIKE Concrete Anchors . . . . . . . 188-191Spud Wrenches . . . . . . . . . . . . . . . . . . . 242Stainless Capped Head Screws . 15, 30, 38STAINLESS STEEL Fasteners BLAZER® 410 Self-drilling . . . . . . . . 10 Concrete Screws. . . . . . . . . . . . . . . 139 Drywall. . . . . . . . . . . . . . . . . . . . . . . . 86 K-Lath . . . . . . . . . . . . . . . . . . . . . . . . 86 SD300 304 Self-drilling . . . . . . . . . . . 11 Security Screw . . . . . . . . . . . . . . . . . 12 Pancake Head . . . . . . . . . . . . . . . . . . 20 Self Tapping . . . . . . . . . . . . . . . . 34, 35

SENTRY PLUS FIVE® . . . . . . . . . . . 56 Post Frame . . . . . . . . . . . . . . . . . . . . 38 Wood Decking . . . . . . . . . . . . . . . . . 39 Wood All-purpose . . . . . . . . . . . . 86, 87Stainless Steel - Technical Data . . 302, 303Stand off Screws . . . . . . . . . . . . . . . . . . . 29Staplers / Staples . . . . . . . . . . . . . . . 51, 52Staple Gun . . . . . . . . . . . . . . . . . . . . . . . 52Steel Framing Screws . . . . . . . . . . . . . . . 84Step Drill Bits . . . . . . . . . . . . . . . . . . . . . 227Storage Boxes (Jobsite) . . . . . . . . . . . . 279STRAP-TOGGLE . . . . . . . . . . . . . . . . . 119STRESS-LESS® Framing Fastener . . . . . 9STRESS-LOK® Clamping Washer . . . . 207Stress Plates . . . . . . . . . . . . . . . . . . . . . . 57Strip Nails . . . . . . . . . . . . . . . . . . . . . . . . 51Strut and Channel Framing . . . . . . 125-129Structural Insulated Panel Screws . . 60-61Stud - Double Ended . . . . . . . . . . . . . . . . 43Square Cap Nail . . . . . . . . . . . . . . . . . . . 70 TamperProof Fasteners and Tools . . . . . . .TAPCON . . . . . . . . . . . . . . . . . . . . 138, 139 Large Diameter . . . . . . . . . . . . 140-143Tapes 3M Extreme Sealing . . . . . . . . . . . . 269 Acrylic Aluminum Duct Facing Foam Foil - Double Face Polyester Vinyl . . . . . . . . . . . . . . . . . . . . . 274-276Tapping Screws Bugle Head . . . . . . . . . . . . . . . . . 82, 83 Countersunk Head . . . . . . . . . . . . . . . 87 Hex Head . . . . . . . . . . . . . . . . . . . 34, 35 Hex Washer Head . . . . . . . . . 36, 37, 42 Hole Sizes . . . . . . . . . . . . . . . . . . . . 291 Pancake Head . . . . . . . . . . . . . . . . . . 20 Pan Head . . . . . . . . . . . . . . . . . . . 40-42 Round Washer . . . . . . . . . . . . . . . 40, 41Technical Data . . . . . . . . . . . . . . . . . . . . 285 ACQ Treated Lumber Information . . 301 Bolt Strength . . . . . . . . . . . . . . 294, 295 Corrosion . . . . . . . . . . . . . . . . . 297-299 Drive Systems . . . . . . . . . . . . . . . . . 287 Fastener Properties . . . . . . . . . 286-296 Galvanic Corrosion Chart . . . . . . . . . 299 Grade Markings . . . . . . . . . . . . . . . . 293 Head Styles . . . . . . . . . . . . . . . . . . . 287 Hole Sizes for Tapping Screws . . . . 291 Material Thickness Chart . . . . . . . . . . 16 Nut Strengths . . . . . . . . . . . . . . . . . . 296 Plating . . . . . . . . . . . . . . . . . . . 298, 300 Point Types . . . . . . . . . . . . . . . 289, 290 Self-Drilling Screw General Data . . . . . . . . . . . . . . . . . . 292 Performance Data . . . . . . . . . . . . 16, 17 Shoulder Types . . . . . . . . . . . . . . . . 288 Stainless Steel . . . . . . . . . . . . . 302, 303 Thread Type . . . . . . . . . . . . . . . . . . . 290

Washer Types . . . . . . . . . . . . . . . . . 288Tension Nails . . . . . . . . . . . . . . . . . . . . . . .50Thread Types. . . . . . . . . . . . . . . . . . . . . 290Torsional Strength . . . . . . . . . . . . . 291, 292Termination Bar . . . . . . . . . . . . . . . . . . . . 59Threaded Rod . . . . . . . . . . . . . . . . . . . . 137Tie Wire . . . . . . . . . . . . . . . . . . . . . 106, 107Tie Wire Insulation Tooling . . . . . . 108, 109TILE-BOND Adhesive . . . . . . . . . . . . . . . 78 Toggle Bolts Lightweight Decks . . . . . . . . . . . . . . . 73 Round Head Slotted . . . . . . . . . . . . . . 43 Strap Toggle . . . . . . . . . . . . . . . . . . . 119Toggles . . . . . . . . . . . . . . . . . . . . . . . . . 116Tools and Accessories . . . . . . . . . . 209-245Tool Repair . . . . . . . . . . . . . . . . . . . . . . 306TRACER® Drywall Screws . . . . . . . . 82, 83 Technical Data . . . . . . . . . . . . . . . . . . .83TRAKFAST Gas Charged Tool . . . . . . . . . . . . . . . 88 Pins and Loads / Technical Data . 89-95TRI-SEAL . . . . . . . . . . . . . . . . . . . . . . . . 19TRUBOLT Wedge Anchors . . . . . . 150, 153TUBE-LOK Fasteners . . . . . . . . . . . . . . . 71TWISTER® Pre-Tied Wires . . . . . . 106, 107

U-Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . 137ULP - Ultra Low Profile Fastener . . . . . . 20Umbrella Inserts and Stubby Screens . . . . . . . . . . . . 178-180 Parts . . . . . . . . . . . . . . . . . . . . . . . . . 179Underlayment - GRACE . . . . . . . . . . . . 265Utility Knives and Blades . . . . . . . . . . . . 244

VICE GRIP Locking Pliers . . . . . . . 238, 239VRT® Technology . . . . . . . . . . . . . . . . . 13

Wall Dog . . . . . . . . . . . . . . . . . . . . 114, 115Warranty . . . . . . . . . . . . . . . . . . . . . . . . 307Washered Fasteners . . . . . . . . . . . . . 14, 15Washers Bonded . . . . . . . . . . . . . . . . . . . . . . . 201 Flat / Fender . . . . . . . . . . . . . . . . . . . 200 Load Distributing (Hillside) . . . . . . . . 206Waterproofing - PEAL & SEAL . . . . . . . 268Wedge Anchor . . . . . . . . . . . . . . . . 150-153Wedge Bolt Fasteners and Drill Bits . . . . . . . . . . 143Wood Boring Drill Bits . . . . . . . . . . 225, 226Wood Deck Screws - Carbon and Stainless . . . . . . . . . . . . . 39, 86, 87Wood Screws Flat Countersunk . . . . . . . . . . . . . 40-42 Post Frame. . . . . . . . . . . . . . . . . . 36-38Wood to Metal Fasteners (BLAZER®) . . 10Wrenches - Spud / Adjustable / Ratchet Box / Structural . . . . . . . . . . . . 242

Zac Zinc Head Screws . . . . . . . . . . . . . . 32ZAMAC Zinc Nail-in Anchor . . . . . 192, 193Zinc Head Fasteners (ZAC) . . . . 15, 30, 32Zip Toggle . . . . . . . . . . . . . . . . . . . . . . . 118

KB

Text Box





TOOLSPages 209-245

SEALANTSPages 246-276

CONTRACTOR SUPPLIESPages 277-284

TECHNICAL DATAPages 285-303

FASTENERS

TFC TFC offers the largest selection offers the largest selection of fasteners for the commercial of fasteners for the commercial construction industry!construction industry!Our wide variety of standard and specialty fasteners makes it easy to select the proper product for your application.We specialize in fastening solutions for those difficult connections, and all of our fasteners are designed for the professional construction trades assuring high performance and long-life.

FASTENERSPages 7-208




Metal Roof Clip Screw

• Drill and tap up to 1/2” thick steel.• Supplied with our TRI-SEALTM long life coating for

superior corrosion protection.• Lengths up to 8” for retrofi t metal roof base attachment.

Heavy Gauge Applications - DP4 & DP5 Points

The hex washer head is the most popular drive system and provides the best stability during installation. Available with TRI-SEALTM long life coating for the ultimate corrosion protection...1,000 hrs salt spray with no red rust!

SizePoint Type

Drilling Thickness

AttachmentThickness

Box Quantity

A

#8-18 x 1/2"#8-18 x 5/8"#8-18 x 3/4"#8-18 x 1"#8-18 x 1-1/4"#8-18 x 1-1/2"#8-18 x 2"

DP2DP2DP2DP2DP2DP2DP2

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.205"

.330"

.455"

.705"1.000"1.205"1.750"

10M10M10M7.5M5M5M

1.5M

B

#10-16 x 1/2"#10-16 x 5/8"#10-16 x 3/4"#10-16 x 1"#10-16 x 1-1/2"#10-16 x 2"#10-16 x 3"

DP3DP3 (HH)DP3 (HH)

DP3DP3DP3DP3

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.150"

.200"

.325"

.575"1.075"1.500"2.500"

10M10M7.5M5M3M2M1M

MATERIAL: C1018-1022 Carbon SteelPLATING: Standard: .0003” Min. Electro Zinc (46hrs Salt Spray - ASTM B117) Meets ASTM C 1513-04 and AISI TS-4-02 Standards

A

B

C

"HH" Denotes High Hex

SizePoint Type

Drilling Thickness

AttachmentThickness

Box Quantity

C

#12-14 x 3/4"#12-14 x 1"#12-14 x 1-1/4"#12-14 x 1-1/2"#12-14 x 2"#12-14 x 2-1/2"#12-14 x 3"


.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.290"

.525"

.750"1.000"1.500"2.000"2.500"

5M3.5M3M2M2M1M1M

D #12-14 x 1-1/4" DP2 LP .036" - .200" .750" 3.5M

E 1/4-14 x 7/8" DP1 W/VRT .036" - .090" .325" 2.5M

F

1/4-14 x 3/4"1/4-14 x 1"1/4-14 x 1-1/4"1/4-14 x 1-1/2"1/4-14 x 2"1/4-14 x 2-1/2"1/4-14 x 4"1/4-14 x 5"1/4-14 x 6"1/4-14 x 8"

DP3DP3DP3DP3DP3DP3DP3DP3DP3DP3

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460" .710".960"

1.460"2.460"3.460"4.460"5.460"7.460"

2.5M2.5M2M2M

1.5M1M500500250250

G #12-14 x 1-1/4" DP2 SHLDR .036" - .200" .750" 3.5M

H5/16-18 x 1"5/16-18 x 1-1/4"5/16-18 x 1-1/2"

DP3DP3DP3

.100" - .250"

.100" - .250"

.100" - .250"

.460"

.710"

.960"

1.5M1.5M1.5M

I

1/4-20 x 1-1/2"1/4-20 x 2-1/4"1/4-20 x 3"1/4-20 x 4"1/4-20 x 5"1/4-20 x 6"1/4-20 x 8"


.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

.500"1.250"2.000"3.000"4.000"5.000"7.000"

2M1M500250250250150

J #12-24 x 7/8"#12-24 x 1-1/4"

DP4DP4

.125" - .137"

.125" - .137".325".375"

5M3.5M

K#12-24 x 1-1/4" #12-24 x 1-1/2" #12-24 x 2"

DP5DP5DP5

.250" - .500"

.250" - .500"

.250" - .500"

.375"

.625"1.125"

3.5M2.5M2M

MATERIAL: C1018-1022 Carbon SteelPLATING: Long-Life: TRI-SEAL™ Coating (1,000hrs Salt Spray - ASTM B117) Meets ASTM C 1513-04 and AISI TS-4-02 Standards

I

J

K

D

E

F

G

H

High Hex for better driving stability!

HEX DRIVE SIZE#8 dia: 1/4" HWH

#10 dia: 5/16" HWH#12 dia: 5/16" HWH1/4 dia: 3/8" HWH5/16 dia: 3/8" HWH

HEX WASHER HEADHEX WASHER HEAD

DRILL SCREWSBLAZER R HIGH PERFORMANCE DRILL SCREWS HIGH PERFORMANCE DRILL SCREWS

FOR COMMERCIAL CONSTRUCTIONFOR COMMERCIAL CONSTRUCTION

SIZES AND PERFORMANCE SPECIFICATIONSSIZES AND PERFORMANCE SPECIFICATIONS




Great for steel framing when multiple thicknesses are used.

STRESS-LESS™ undercut head is designed to eliminate stress that concentrates under the head of fasteners.

STRESS-LESSTM Great for Retrofi t Framing

General framing applications Cross recess (phillips) drive.

Pancake head provides extra clearance compared to round washer head fasteners.

#2 Square/cross recess for exceptional driving stability...NO CAM-OUT!

Pan Framer Head

MATERIAL: C1018-1022 Carbon SteelPLATING: .0002” Min. Electro Zinc (24hrs Salt Spray)

MATERIAL: C1018 - 1022 Carbon Steel PLATING: .0003” Min. Electro Zinc with yellow di-chromate(48hrs Salt Spray)

MATERIAL: C1018-1022 Carbon SteelPLATING: .0003” Min. Zinc w/TRI-SEAL™ Coating (1,000hrs Salt Spray)

Radius under thehead concentrates

stress that can cause failure.

STRESS-LESS™undercut distributes

stress across the washer face.

Standard STRESS-LESS™

Pan Head

Pan Head

A

B

C

D

E

F

G

Round Washer Head / Pan Head

Great for Mini-Storage!

#2 Square Drive Power Bit

#2 Cross Recess Drive

HEAD TYPE#12 dia: 5/16" HWH1/4 dia: 5/16" HWH

Long-pilot Point

DRILL SCREWSBLAZER R HIGH PERFORMANCE DRILL SCREWS HIGH PERFORMANCE DRILL SCREWS

FOR COMMERCIAL CONSTRUCTIONFOR COMMERCIAL CONSTRUCTION

PAN FRAMER - ROUND WASHER - PAN HEADPAN FRAMER - ROUND WASHER - PAN HEAD

PANCAKE HEAD SCREWSPANCAKE HEAD SCREWS

LONG PILOT AND STRESS-LESS FEATURELONG PILOT AND STRESS-LESS FEATURE

SizePoint Type

Drilling Thickness

Attachment Thickness

Box Quantity

A #7-16 x 3/4" DP2 .036" - .100" .375" 10M

B

#8-18 x 1/2"#8-18 x 5/8"#8-18 x 3/4"#8-18 x 1"#8-18 x 1-1/4"#8-18 x 1-1/2"#8-18 x 2"


.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.036" - .100"

.205"

.330"

.455"

.705"1.000"1.205"1.750"

10M10M10M7.5M5M5M

1.5M

C

#10-16 x 1/2"#10-16 x 5/8"#10-16 x 3/4"#10-16 x 1"#10-16 x 1-1/4"#10-16 x 1-1/2"

DP3DP3DP3DP3DP3DP3

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.036" - .175"

.150"

.200"

.325"

.575"

.825"1.075"

10M10M7.5M5M

3.5M3M

SizePoint Type

Drilling Thickness


Box Quantity

F #12-14 x 7/8" DP3 .036" - .210" .325" 2.5M

G 1/4-14 x 7/8" DP3 .036" - .250" .325" 2.5M

SizePoint Type

Drilling Thickness


Box Quantity

D #10-16 x 5/8" DP3 .036" - .175" .200" 10M

E #10-24 x 5/8" DP3 .036" - .175" .200" 10M







Provides corrosion resistance inmild atmospheres.

Plated to resist surface rust and to reduce drive torque.

For additional corrosion protection, specify TRI-SEAL™ long-life coating.

MATERIAL: 410 Stainless SteelPLATING: Passivated (24hrs Salt Spray), Zinc Plated (48hrs Salt Spray), * Denotes TRI-SEALTM Coated (1,000hrs Salt Spray)

MATERIAL: Carbon SteelPLATING: .0003” min zinc TRI-SEALTM Coated (1,000hrs Salt Spray)

NEW! BLAZER® HEADER Heavy Gauge (1/2” SD) designed to attach up to 1/2” thick steel.

Fasten wood-to-metal. No pre-drilling required. TRI-SEAL™ coated for use in ACQ lumber.

SizePoint Type

Drilling Thickness

AttachmentThickness

Box Quantity

A #8-18 x 1/2" #8-18 x 3/4"

DP2DP2

.036" - .100"

.036" - .100".205".455"

10M10M

B#10-16 x 3/4" #10-16 x 1" #10-16 x 1-1/2"

DP3DP3DP3

.036" - .175"

.036" - .175"

.036" - .175"

.325"

.575"1.075"

7.5M5M3M

C

#12-14 x 3/4" *#12-14 x 1" *#12-14 x 1-1/4" *#12-14 x 1-1/2" #12-14 x 2"

DP3DP3

DP3 LPDP3DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.290"

.525"

.550"1.000"1.500"

5M3.5M2.5M2.5M2M

D *#12-14 x 1-1/4" #12-14 x 1-1/2"

DP5DP5

.250" - .500"

.250" - .500"1.000"1.205"

5M5M

E *1/4-14 x 7/8" *1/4-14 x 1-1/8"

DP1DP1

.036" - .090"

.036" - .090".375".875"

2.5M2.0M

F

*1/4-14 x 3/4"*1/4-14 x 1" *1/4-14 x 1-1/2"1/4-14 x 2"

DP3DP3DP3DP3

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460"

.960"1.460"

2.5M2.5M2M

1.5M

SizePoint Type

Drilling Thickness


Box Quantity

G #10-24 x 1-7/16" DP3 WW .036" - .210" .750" 4M

H #12-14 x 1-3/4"#12-14 x 2-1/2"

DP2 WWDP2 WW

.036" - .210"

.036" - .210".750"

1.625"2M1M

I #12-24 x 2"#12-24 x 2-1/2"

DP4 WWDP4 WW

.036" - .210"

.036" - .210"1.250"1.750"

2M1M

J1/4-20 x 2-3/4"1/4-20 x 3-1/4"1/4-20 x 3-3/4"

DP4 WWDP4 WWDP4 WW

.125" - .375"

.125" - .375"

.125" - .375"

2.000"2.750"3.000"

900900500

K 1/4-20 x 3-1/8" DP5 WW .125" - .500" 1.625" 1M

SizePoint Type

Drilling Thickness


Box Quantity

L #10-16 x 1-3/16" DP3 .036" - .175" .750" 2.5M

M

#10-24 x 3/4"#10-24 x 1"#10-24 x 1-1/4"#10-24 x 1-1/2"

DP3DP3DP3DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.375"

.500"

.750"

.875"

5M5M

3.5M3M

Flat Wafer

Flat Countersunk

A

B

C

D

E

F

G

H

I

J

K

L

M

"WW" Denotes With Wings

MATERIAL: Carbon SteelPLATING: .0003” min zinc TRI-SEALTM Coated (1,000hrs Salt Spray)

HEAD TYPE#8 dia: 1/4" HWH

#10 dia: 5/16" H WH#12 dia: 5/16" HWH*1/4 dia: 5/16" HWH

1/4 dia: 3/8 HWH

DRILL SCREWSBLAZER R

410 STAINLESS STEEL DRILL SCREWS410 STAINLESS STEEL DRILL SCREWS

WOOD-TO-METAL DRILL SCREWSWOOD-TO-METAL DRILL SCREWS

HIGH PERFORMANCE DRILL SCREWS HIGH PERFORMANCE DRILL SCREWS FOR COMMERCIAL CONSTRUCTIONFOR COMMERCIAL CONSTRUCTION






Triangle Fastener offers a full line of fasteners manufactured from 304 stainless steel. The fastener head and threads are produced from corrosion resistant stainless steel producing exceptional corrosion protection and superior ductility. A carbon steel drill point is hardened and welded to the body allowing the fastener to drill and tap in steel up to 1/2" thick!

304 304 STAINLESS STEEL STAINLESS STEELDRILL SCREWSDRILL SCREWS

304 STAINLESS STEEL DRILL SCREWS304 STAINLESS STEEL DRILL SCREWS





Security screws specifically designed for metal siding and roofing applications

TORX® PIN-HEADMaximum torque transfer and positive tool engagement means easier drive installation with less pressure and slippage. Torx® Pin Head offers a high degree of security and requires matching drive bit. Available in button head for neat appearance.

Contact Triangle Fastener for additional sizes and types for security screws.

SECURITY SCREWSSECURITY SCREWS

Does your building need security? Mini Storage Prisons Government Buildings Banks Dealerships

Assembled with a BOND-SEALER™ sealing washer that has EPDM vulcanized to a 20 Gauge galvanized backing that will withstand harsh weather conditions.

MATERIAL: C1018-1022 Carbon SteelPLATING: .0003” Min. Zinc plating w/ yellow chromate (48hrs Salt Spray)

CORRECTSlight circle of sealant

extrudes to outer edge.

TOO TIGHT!Metal backing

begins to turn up.

TOO LOOSESealant is not compressed and can not form a seal.

To assure a proper seal, torque the fastener until the EPDM sealant extrudes to the outer edge of the backing material.

SizePoint Type

Drilling Thickness


Box Quantity

#12-14 x 1-1/2" DP3 LP .036" - .210" 1.000" 2.0M

1/4-14 x 7/8" DP1 .036" - .090" .325" 2.5M


We supply insert bits to make installation fast and easy!

DISCLAIMER: ALL TEST RESULTS AND SPECIFICATIONS ARE A RESULT OF LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. SINCE APPLICATION CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.

Pullout Test Result - Ultimate Average in Pounds

FastenerSize

GAGE THICKNESS & ROCKWELL HARDNESS OF THE TEST PLATE26 Ga.(.018")

45-49Rb

24 Ga.(.024")

46-52Rb

22 Ga.(.030")

61-67Rb

20 Ga.(.036")

54-62Rb

18 Ga.(.048")

64-73Rb

16 Ga.(.060")

65-67Rb

14 Ga.(.075")

68-70Rb

12 Ga.(.105")

74-86Rb

1/8"(.125")

75-91Rb#12-14 DP3 533 752 1163 1947 22501/4-14 DP1 173 240 337 387 657 1250

Available in 410 stainless steel. Call for details.

T-27 Torx Pin Recess Drive

Manufactured to SAE J78 specifi cations.




BACK-OUT RESISTANT SCREWSBACK-OUT RESISTANT SCREWS

Description Part NumberCarton

QuantityWT Per M Pcs

1/4” -14 X 7/8” DP1/LAP w/VRT®CONCEALOR® Pancake Headw/Bonded Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14087C1TSVBW 2,500 pcs250/Bag 13.5#

1/4” -14 X 7/8” DP1/LAP w/VRT® BLAZER® Flange Head w/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14087HW1CSTSVW 2,500 pcs250/Bag 13.5#

1/4” -14 X 7/8” DP1/LAP w/VRT®BLAZER®TRI-SEAL™ Coated1,000Hrs Salt Spray

14087HW1CSTSV 2,500 pcs250/Bag 10.2#

1/4” -14 X 7/8” DP1/LAP w/VRT®BLAZER® w/Bonded Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14087HW1CSTSVBW 2,500 pcs250/Bag 13.5#

1/4” -14 X 7/8” DP1/LAP w/VRT®BLAZER® Stainless Cap Headw/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14087HW1CSTSVWSC 2,500 pcs250/Bag 13.5#

1/4” -14 X 7/8” DP1/LAP w/VRT®BLAZER® Zinc Cap Headw/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14087HW1CSTSVWZC 2,000 pcs250/Bag 13.5#

1/4” -14 X 1-1/8” DP1/LAP w/VRT®BLAZER® Stainless Cap Head w/Sealing WasherTRI-SEAL™ Coated1,000Hrs Salt Spray

14112HW1CSTSVWSC 2,000 pcs250/Bag 19.3#

#17-14 X 1” TYPE AB w/VRT® TAPPERw/Bonded Sealing Washer (3/4”OD)TRI-SEAL™ Coated1,000Hrs Salt Spray

17100HHACSTSVOW 2,000 pcs250/Bag 20#

Specifi cationsBLAZER Drill Screws conforms to SAE J-78 for self-drilling tapping screws.

#17 TAPPER conforms to ANSI/ASME B18.6.4 for tapping screws.

Material Carbon Steel: C1022 Stainless Cap: 304 SS Zinc Cap: Zamac 5

Tensile Strength 1/4-14: 4,275 lbs. 1/4-14: 4,275 lbs. #17-14: 5,200 lbs. #17-14: 5,200 lbs.

Torsional StrengthTorsional Strength 1/4-14: 150 lbs-inch 1/4-14: 150 lbs-inch #17-14: 175 lbs-inch #17-14: 175 lbs-inch

*Pullout (Pounds)*Pullout (Pounds) 1/4-141/4-14 #17-14#17-1426ga 173 20126ga 173 20124ga 240 28024ga 240 28022ga 337 34222ga 337 34220ga 387 39520ga 387 39518ga 657 72518ga 657 72516ga 1,250 1,34516ga 1,250 1,345

Corrosion ResistanceCorrosion ResistanceTRI-SEALTRI-SEALSalt Spray: 1,000 hrs Salt Spray: 1,000 hrs minimum.minimum.No Red RustNo Red Rust

Sealing WashersSealing WashersFlange Head:Flange Head: EPDM Cut Tubular EPDM Cut Tubular

Bonded Washer:Bonded Washer: EPDM Vulcanized to EPDM Vulcanized to G-90 Galvanized Steel. G-90 Galvanized Steel. (15MM O.D.). (15MM O.D.).

* Pullout values are * Pullout values are ultimate averages based ultimate averages based on laboratory tests. on laboratory tests. Appropriate factors of Appropriate factors of safety should be used. TFC safety should be used. TFC assumes no liability for the assumes no liability for the use if this information. use if this information.

Our Vibration Resistant Thread (VRT®) is designed to signifi cantly increase back-out torque and reduce the potential for leaks.VRT® keeps the fastener tighter in applications where expansion, contraction and vibration are a concern.Independent tests verify that VRT® produces 3-1/2 times more back-out resistance than a standard thread.

Light Gauge ApplicationsLight Gauge ApplicationsMaximum Drilling Thickness: .090”

Technical DataTechnical Data




BOND-SEALER™ is a sealing washer that has EPDM vulcanized to a 20 Gauge galvanized backing that will withstand harsh weather conditions.

TRI-SEAL™ long life coated for superiorcorrosion protection.

WASHER DETAILS20 ga G-90 Galvanized Steel

Vulcanized to .062” thick EPDM15MM OD Washer

LP denotes long-pilot design for metal roofi ng and siding

MATERIAL: C1018-1022 Carbon SteelPLATING: .0003” Min. Zinc w/TRI-SEALTM Coating (1,000hrs Salt Spray)

CORRECTSlight circle of sealant ex-

trudes to outer edge.

TOO TIGHT!Metal backing

begins to turn up.

TOO LOOSESealant is not compressed and can not form a seal.

To assure a proper seal, torque the fastener until the EPDM sealant extrudes to the outer edge of the backing material.

Proper Fastener Installation

SizePoint Type

Drilling Thickness


Box Quantity

A #10-16 x 1"#10-16 x 1-1/2"

DP3DP3

.036" - .175"

.036" - .175".575"

1.075"5M3M

B

#12-14 x 3/4"#12-14 x 1" #12-14 x 1-1/4" #12-14 x 1-1/2" #12-14 x 2" #12-14 x 2-1/2"#12-14 x 3"

DP3DP3

DP3 LPDP3DP3DP3DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.290"

.525"

.750"1.000"1.500"2.000"2.500"

5M3.5M3.5M2.5M2M1M1M

C#12-24 x 1-1/4"#12-24 x 1-1/2"#12-24 x 2"

DP5DP5DP5

.250" - .500"

.250" - .500"

.250" - .500"

.375"

.625"1.125"

3.5M2.5M2M

D 1/4-14 x 7/8" DP1 W/VRT* .036" - .090" .325" 2.5M

E

1/4-14 x 3/4"1/4-14 x 1" 1/4-14 x 1-1/4" 1/4-14 x 1-1/2" 1/4-14 x 2"1/4-14 x 2-1/2"1/4-14 x 4"1/4-14 x 5"1/4-14 x 6"

DP3DP3DP3DP3DP3DP3DP3DP3DP3

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460"

.710"

.960"1.460"2.460"3.460"4.460"5.460"

2.5M2.5M2M2M

1.5M1M500500250

F

1/4-20 x 4"1/4-20 x 5"1/4-20 x 6"1/4-20 x 7"1/4-20 x 8"

DP5DP5DP5DP5DP5

.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

.250" - .500"

3.000"4.000"5.000"6.000"7.000"

500500250150150

FLANGE-SEAL™ self-sealing fastener has a deep undercut head that entraps the EPDM sealing washer to assure a leak free seal.

TRI-SEAL™ long-life coated for superiorcorrosion protection.

MATERIAL: C1018-1022 Carbon SteelPLATING: .0003” Min. Zinc w/TRI-SEALTM Coating (1,000hrs Salt Spray)

WASHER DETAILS.125” Thick EPDM

SizePoint Type

Drilling Thickness


Box Quantity

G

#12-14 x 3/4"#12-14 x 1" #12-14 x 1-1/4"#12-14 x 1-1/2" #12-14 x 2" #12-14 x 2-1/2"

DP2/DP3DP2/DP3

DP2/DP3 LPDP2/DP3DP2/ DP3DP2/DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.290"

.525"

.750"1.000"1.500"2.000"

5M3.5M3.5M2.5M2M1M

H 1/4-14 x 7/8" DP1 W/VRT* .036" - .090" .325" 2.5M

I1/4-14 x 3/4"1/4-14 x 1" 1/4-14 x 1-1/2"

DP3*DP3*DP3*

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460"

.960"

2.5M2.5M2M


A

B

C

D

E

F

G

H

I

HEAD TYPE#10 dia: 5/16" HWH#12 dia: 5/16" HWH*1/4 dia: 5/16" HWH1/4 dia: 3/8" HWH


BLAZERBLAZER®® FLANGE-SEAL HEAD WITH EPDM WASHER FLANGE-SEAL HEAD WITH EPDM WASHER

BLAZERBLAZER®® WITH BONDED SEALING WASHER WITH BONDED SEALING WASHER




HEAD TYPE#12 dia: 5/16" HWH1/4 dia: 5/16" HWH




MATERIAL HEAD: 302 Stainless Steel THREAD: Carbon SteelPLATING HEAD: Passivated THREAD: .0003” Min. Zinc with TRI-SEAL ™ Long-life CoatingCORROSION HEAD: >2,000hrs Salt Spray THREAD: 1,000hrs Salt Spray

304 stainless steel cap head for exceptional corrosion resistance.

Our special head is designed to produce maximum torsional strength and a leak free seal.

TRI-SEAL™ long life coated shank for superior corrosion protection.

WASHER DETAILS .100” Thick EPDM

LP denotes long-pilot design for metal roofi ng and siding Size

Point Type

Drilling Thickness


Box Quantity

F

#12-14 x 1" #12-14 x 1-1/4"#12-14 x 1-1/2" #12-14 x 2"

DP2/DP3DP2/DP3 LP

DP2/DP3DP2/DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.525"

.750"1.000"1.500"

3.5M3.5M2.5M2M

G 1/4-14 x 7/8" DP1 W/VRT .036" - .090" .325" 2.5M

H

1/4-14 x 3/4"1/4-14 x 1" 1/4-14 x 1-1/4"1/4-14 x 1-1/2"

DP3DP3DP3DP3

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460"

.375"

.960"

2.5M2.5M2M2M

I #17-14 x 1" TYPE AB W/VRT 20ga or less .750" 2.5M

F

G

H

I

BLAZERBLAZER®® STAINLESS CAP HEAD WITH EPDM SEALING WASHER STAINLESS CAP HEAD WITH EPDM SEALING WASHER

ZAMAC 5 zinc alloy cap head for premium corrosion resistance WILL NOT RED RUST!

Special head is designed to produce maximum torsional strength and a leak free seal.

MATERIAL HEAD: Zamac 5 Zinc Alloy THREAD: Carbon SteelPLATING HEAD: Plain Finish THREAD: .0003” Min. Zinc with TRI-SEAL™ Long-life Coating.CORROSION RESISTANCE HEAD: No Red Rust THREAD: 1,000hrs Salt Spray

WASHER DETAILS .125” Thick EPDM

Need a 3/8” Hex Washer Head? Contact us for available sizes.


SizePoint Type

Drilling Thickness


Box Quantity

A

#12-14 x 1" #12-14 x 1-1/4"#12-14 x 1-1/2" #12-14 x 2"

DP2/DP3DP2/DP3 LP

DP2/DP3DP2/DP3

.036" - .210"

.036" - .210"

.036" - .210"

.036" - .210"

.525"

.750"1.000"1.500"

3.5M3.5M2.5M2M

B 1/4-14 x 7/8" DP1 W/VRT .036" - .090" .325" 2.5M

C

1/4-14 x 3/4"1/4-14 x 1" 1/4-14 x 1-1/4"1/4-14 x 1-1/2"

DP3DP3DP3DP3

.036" - .250"

.036" - .250"

.036" - .250"

.036" - .250"

.210"

.460"

.375"

.960"

2.5M2.5M2M2M

D 1/4-14 x 1" TYPE AB 20ga or less .750" 2.5M

E #17-14 x 1" TYPE AB 20ga or less .750" 2.5M

A

B

C

D

E

HEAD TYPE#12 dia: 5/16" HWH1/4 dia: 5/16" HWH#17 dia: 5/16" HWH

BLAZERBLAZER®® ZINC CAP HEAD WITH EPDM SEALING WASHER ZINC CAP HEAD WITH EPDM SEALING WASHER





HEAD TYPE#12 dia: 5/16" HWH1/4 dia: 5/16" HWH#17 dia: 5/16" HWH




BLAZER® self-drilling fasteners are produced and perform to SAEJ78, ASME/ANSI 18.18. and AISI TS-4-02 specifi cations. Conforms to ICCESAC18 acceptance criteria for tapping screw fasteners.

The following information is compiled to assist the design professional in selecting the appropriate fastener for the application. Data supplied is compiled from fastener standards and independent tests. An engineering professional should be consulted to determine expected loads on the connection, environmental effects, and any other conditions that could effect the performance of the fastener. Selecting a fastener is the responsibility of the engineer and changes to a fastener should not be made without approval. Using the wrong fastener can lead to failure. TFC WILL NOT WARRANTY, EITHER EXPRESSED OR IMPLIED,THE USE OF THIS INFORMATION.

TorsionalThread Description Tensile


Pounds - Ultimate Average

These pullover results are for self-sealing fasteners listed in this catalog.

Note: Estimated pullover for fasteners without sealing washers can be calculated using the following formula per AISI.

Pullover force = 1.5 -x- Thickness of the member in contact with the screw head. -x- Larger of the screw head diameter or washer diameter. -x- Tensile strength of the member in contact with the screw head.

Fastener Diameter

Nominal Screw Diameter

Major Diameter (inch)

Minor Diameter (inch)

Area Of Minor Dia. (sq in.)

Torsional (Lb-In.)

Tensile(Pounds)

Shear(Pounds)

Max Min Max Min#6-20 0.138 0.139 0.135 0.104 0.099 0.0077 25 1,125 750#8-18 0.164 0.166 0.161 0.122 0.116 0.0106 42 1,575 1,000

#10-16 0.190 0.189 0.183 0.141 0.135 0.0143 61 2,100 1,400#10-24 0.190 0.190 0.182 0.144 0.137 0.0147 65 3,400 2,275#12-14 0.216 0.215 0.209 0.164 0.157 0.0194 92 2,778 2,000#12-24 0.216 0.216 0.209 0.189 0.185 0.0269 100 3,188 2,1001/4-14 0.250 0.246 0.240 0.192 0.185 0.0269 150 4,275 2,6001/4-20 0.250 0.250 0.242 0.218 0.214 0.0360 156 4,275 2,700#18-9 0.306 0.306 0.300 0.217 0.209 0.0343 170 4,550 2,576

5/16-12 0.313 0.329 0.327 0.309 0.299 0.0702 250 8,550 5,700

English to Metric Formula to Use

Decimal to Millimeters Decimal x 25.4

PSI to Newton / Millimeters² PSI x .007

Pounds Force to Newtons Pounds Force x 4.448

Gauge Thickness Decimal Metric

29 GA .013" .33mm

28 GA .015" .38mm

26 GA .018" .46mm

24 GA .024" .61mm

22 GA .030" .76mm

20 GA .036" .91mm

18 GA .048" 1.22mm

16 GA .060" 1.52mm

14 GA .075" 1.91mm

12 GA .105" 2.67mm

1/8" .125" 3.18mm

10 GA .135" 3.43mm

1/4" .250" 6.35mm

5/16" .312" 7.92mm

3/8" .375" 9.53mm

1/2" .500" 12.7mmSteel

ThicknessBOND-SEALER FLANGE

SEALERZINC

CAP HEADSTAINLESSCAP HEAD12.7MM OD 15MM OD

22 ga 945 1,249 1,298 1,647 1,29824 ga 704 1,056 1,102 1,310 1,10226 ga 519 654 692 794 692

Material: C1018-C1022 / 410 SSHeat Treatment: Case Harden Case Hardness: 52-58 Rockwell C Case Depth: #6 Dia = .002” - .007” #8, #10, #12 Dia = .004” - .009” 1/4” = .005” - .011” Core Hardness Carbon Steel: 32-40 Rockwell C 410 Stainless: 42-48 Rockwell CDuctility: 5 Degree minimum bend

Shear

TECHNICAL DATATECHNICAL DATADRILL SCREWSBLAZER R

PULLOVER TEST RESULTSPULLOVER TEST RESULTS

TECHNICAL DATA TECHNICAL DATA

MINOR

MAJOR

BLAZERBLAZER®® ENGINEERING DATA ENGINEERING DATA




LoadLoad

The following fastener pullout loads are a result of independent tests conducted at Stork Herron Testing Laboratories. The results are ultimate averages as a result of conducting three pullouts per fastener size in each material thickness.

Shear tests are a result of installation of the fastener in the noted gauge thickness and applying load until failure occurs.


Pullout Test Result - Ultimate Average in Pounds

FastenerSize

GAGE THICKNESS & ROCKWELL HARDNESS OF THE TEST PLATE26 Ga.(.018")

45-49Rb

24 Ga.(.024")

46-52Rb

22 Ga.(.030")

61-67Rb

20 Ga.(.036")

54-62Rb

18 Ga.(.048")

64-73Rb

16 Ga.(.060")

65-67Rb

14 Ga.(.075")

68-70Rb

12 Ga.(.105")

74-86Rb

1/8"(.125")

75-91Rb

3/16"(.188")

83-85Rb

1/4"(.250")

92-96Rb

1/2"(500")

92-93Rb#6-20 DP2 120 183 248 296 241 679 847#8-18 DP2 120 193 243 297 447 703 910#10-16 DP3 153 207 243 293 487 710 900 1327 1503#10-24 DP2 161 238 293 324 517 1096 1544 1906#12-14 DP2 577 790 1137 1697 1920#12-14 DP3 533 752 1163 1947 2250 2870#12-24 DP5 687 986 1850 1670 2673 3844* 18731/4-14 DP1 173 240 337 387 657 12501/4-14 DP3 343 533 886 1077 2170 2060 3863 4493*1/4-20 DP5 708 3853 4283* 4680*5/16-12 DP3 457 706 1609 1707 2831 2915 3745

Size 26 Ga.(.018")

24 Ga.(.024")

22 Ga.(.030")

20 Ga.(.036")

18 Ga.(.048")

16 Ga.(.060")

14 Ga.(.075")

12 Ga.(.105")

#6-20 DP2 278 466 526 758 845

#8-18 DP2 294 496 560 740 1,060

#10-16 DP3 728 1,266 1,540 1,552

#12-14 DP3 769 1,358 1,620 1,970 1,986

#12-24 DP5 2,650

1/4-14 DP3 930 1,442 2,100 2,584 2,650

1/4-20 DP4 2,650

* Exceeds Tensile Strength

A minimum of three (3) full threads must extend beyond the test coupon

Fixture (Secured)

Test Coupon

Install the fastener through the center of the hole.

Fastener pulled in this direction

F

Hole Diameter: 1.500”

Setup of Pullout Test

Stork Herron Report #TRI081-05-01-88910-1

Test Material: 55ksi - 100ksi

TECHNICAL DATATECHNICAL DATA

SHEAR TEST RESULTSSHEAR TEST RESULTS

PULLOUT TEST RESULTSPULLOUT TEST RESULTS





The following information was compiled from known data that compares various fi nishes in a controlled environment. The material set forth herein is for general information only and cannot be construed as a substitute for competent professional advice or service. Any part considering application use of this information does so at their own risk and assumes any and all liability from application or use. Consult a corrosion specialist to determine the best fastener for your condition.

SALT SPRAY Per ASTM B117 (Hours to red rust) Carbon steel and 410 stainless steel materialsCoating Salt Spray.00015” min. (3 um) zinc plate with clear chromate 24hrs.0002” min. (6um) zinc with clear chromate 32hrsPassivated 410 Stainless Steel 48hrs.0003” min. (8 um) zinc plating with clear chromate 48hrs.0003” min. (8 um) zinc plating with yellow di-chromate 144hrs.0005” min. (12 um) zinc plating with clear chromate 60hrs.0007” min. (14 um) mechanical zinc with clear chromate 72hrsEpoxy (E-Coat) 500hrsTRI-SEAL™ Long-life coating 1,000hrs

The chart to the right provides general information with regard to corrosion resistance of various plating and coatings. Contact TFC for detailed information.

Table developed by the Metal Construction Association Members (Rev. by MBMA 09.17.10)

SALT SPRAY RESULTSSALT SPRAY RESULTS

Note 1: Cautionary Guideline: This table serves as a guideline for the selection of fasteners used with metal roofing. The performance of compatible fasteners shown in this table matches the expected life of the metal roof or wall cladding materials. However, in highly corrosive environments such as heavy industrial, coastal marine, high airborne pollutants or salt spray, preservative treated lumber or fire-retardant lumber, the compatibility of certain fasteners with metal roofing or wall cladding materials may be affected. In those types of applications, the manufacturers of the fastener and metal panel will have specific and unique recommendations.

In addition, in the event that certain coating barriers are damaged or scratched through to the substrate there is increased potential for premature corrosion. Care should be taken during installation and during routine maintenance of the panels in order to protect the integrity of the coatings used for metal panels.Note 2: Screws should be plated/coated per ASTM F1941Note 3: Nails should be galvanized per ASTM A153Note 4: Not recommended for coastal and heavy industrial environments

CORROSION PROTECTION INFORMATIONCORROSION PROTECTION INFORMATION

Special Note: Preservative-Treated Lumber ApplicationsACQ, Penta, CA or CBA preservative-treated lumber can be incompatible with certain types of fasteners. In those cases where any type of metal roof or wall cladding materials are being attached to preservative treated lumber, the following fasteners are not compatible: zinc plated screws, zinc-alloy headed screws, stainless capped screws, aluminum, copper and copper alloy. When attaching metal panels to those types of preservative-treated lumber, a moisture barrier should be used between the lumber and the panel material. Metal panel fasteners that are compatible with preservative-treated lumber are stainless steel fasteners, or hot dip galvanized nails manufacturedto ASTM A153 class D or heavier. Other types of fasteners coated with proprietary anti-corrosive technologies are also available for use with preservative-treated lumber. In addition, zinc-plated screws can be used in CCA and MCQ pressure-treated lumber.

FASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CLADDINGFASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CLADDING


Metal Roof orWall Cladding Material

Fastener Material

Zinc Plated Steel

Screws2

Organic Coated Steel

Screws2

Hot-Dip Galvanized Steel Nails3 and Screws

Zinc-Alloy Head Steel

Screws

Stainless Capped Head Steel Screws Aluminum

Copper and Copper Alloys

300 Series

Stainless Steel

400 Series

Stainless Steel

Unpainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesPainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesUnpainted Galvalume Steel No Yes Yes Yes Yes Yes No Yes YesPainted Galvalume Steel Yes4 Yes Yes Yes Yes Yes No Yes4 Yes4

Aluminum No Yes No No No Yes No Yes NoCopper & Copper Alloys No No No No No No No Yes Yes4Stainless Steel No No No Yes Yes Yes Yes Yes YesZinc alloy No No No No No Yes No Yes Yes




Corrosion TestingSalt Spray: 1,000hrs.Per ASTM B117.No red rust

Kesternich: 30 cycles.Per DIN 50018


Contact TFC for additional details on TRI-SEALTM.

TRI-SEAL™ Long-Life Coating TRI-SEAL™ Long-Life Coating is a high performance dip spin fi nish, is a high performance dip spin fi nish, developed to minimize corrosion when used in exterior building applications. It developed to minimize corrosion when used in exterior building applications. It consists of three layers; the fi rst layer is a metallic zinc layer, the second layer consists of three layers; the fi rst layer is a metallic zinc layer, the second layer is a high-grade anti-corrosion chemical conversion fi lm and the third, outer is a high-grade anti-corrosion chemical conversion fi lm and the third, outer layer, is a baked ceramic surface coating.layer, is a baked ceramic surface coating.

The distinguishing feature of The distinguishing feature of TRI-SEAL™TRI-SEAL™ is the tight joining of the baked is the tight joining of the baked ceramic surface coating and the chemical conversion fi lm. These two layers ceramic surface coating and the chemical conversion fi lm. These two layers are bonded together through chemical reactions, and this unique method of are bonded together through chemical reactions, and this unique method of combining layers result in a rigid combination of the coating fi lms.combining layers result in a rigid combination of the coating fi lms.

■ Excellent resistance against gas, weather, and other kinds of corrosion factors, including salt water.

■ Compatible for use in ACQ and Fire Treated Lumber. ■ Composite layers minimize the effect of scratches on the

protection coating.

Test Items Test Methods Test Results

Hardness Peeling test by pencil hardness Over 4H

Adhesion Peeling test by adhesive tape on cross scribed test piece in 1 mm width Nothing abnormal

Acid Resistance Immersion in 5% sulfuric acid solution for 24 hours Nothing abnormal

Alkali Resistance Immersion in 5% sodium hydroxide solution for 72 hours Nothing abnormal

Heat Resistance Exposure to 250 C (482 F) heat for an hour Nothing abnormal

Accelerated Weathering Sunshine weather-0-meter test for 1,000 hours Free from red rust

Contact Corrosion w/other Metals

Corrosive investigation after Salt Spray Test (JIS Z2371) done comparatively on surface treated steel bolts/nuts tightened on a stainless steel plate

Clearly superior to zinc electroplated (colored

chromate) and hot dip galvanizing

Layer 1 - Baked Ceramic Surface Coating Layer Corrosive elements are intercepted by the strong paint fi lm made of ceramic materials.

Layer 2 - Chemical Conversion Coating Layer Rust proof performance is improved as the chemical conversion inactivates the zinc plated surface and creates a tight adhesion between the chemically converted layer and the paint layer.

Layer 3 - Metallic Zinc Layer The steel / iron substrate is protected from corrosion by the self-sacrifi cial galvanic effect of the zinc coating.

Layer 4 - Fastener

Salt Spray Test Results1,000hrs Per ASTM B117

Compatible for use in treated lumber

SEM IMAGINGSEM IMAGING

TRI-SEAL™ LONG-LIFE COATINGTRI-SEAL™ LONG-LIFE COATING

MATERIAL PROPERTIESMATERIAL PROPERTIES





#2 Combo Square/Phillips Recess Drive

Bagged 250 pcs. per bag for your convenience!

A

B

C

D

E

F

G

H

I

DescriptionDrilling

Thickness Part NumberCarton

QuantityWT Per M Pcs

A #10-13 X 1” GP LLLong-life TRI-SEAL™ coated <= 20 ga. 101000CGC 5,000 pcs 7.9#

B #10-13 X 1” GP302 Stainless Steel Aluminum 101000CESS 5,000 pcs 7.9#

C #10-9 X 1” TYPE 17Long-life TRI-SEAL™ coated <= 20 ga. 101000CGC17 5,000 pcs 7.9#

D #10-9 X 1-1/8” ULPLong-life TRI-SEAL™ coated <= 24 ga. 101125CGWC 5,000 pcs 8.2#

E #10-9 X 1-1/8” ULP410 Stainless Steel <= 24 ga. 101125CGWSS 5,000 pcs 8.2#

F #10-13 X 1-1/2” GPLong-life TRI-SEAL™ coated <= 20 ga. 101500CGC 2,500 pcs 10.5#

G #10-13 X 1-1/2” GP302 Stainless Steel Aluminum 101500CESS 2,500 pcs 10.5#

H #10-13 X 2” GPLong-life TRI-SEAL™ coated <= 20 ga. 102000CGC 2,500 pcs 14.0#

I #12-14 X 1” GP LLLong-life TRI-SEAL™ coated <= 20 ga. 121000CGC 5,000 pcs 10.0#

J #10-16 X 5/8” DP3.0003” Zinc and Yellow .175” Max 100625C2 5,000 pcs 7.3#

K #10-24 X 5/8” DP3.0003” Zinc and Yellow .210” Max 100625PBLZ 5,000 pcs 7.3#

L #10-16 X 1” DP3.0003” Zinc and Yellow .175” Max 101000C3 5,000 pcs 7.9#

M #10-16 X 1” DP3410 Stainless Steel .175” Max 101000C34S 5,000 pcs 7.9#

N #12-14 X 1” DP3 LLLong-Life TRI-SEAL™ Coated .210” Max 121000C3C 5,000 pcs 10.0#

O #12-14 X 1” MP.0003” Zinc and Yellow 14 ga. Max 121000CMP 5,000 pcs 9.8#

P 1/4-14 X 1” DP3.0003” Zinc and Yellow 1/4” Max 141000C3YZ 2,500 pcs 14.0#

Sizes

J

K

L

M

N

O

P

Army Corp of Engineers

Use the original...CONCEALOR ULP

ultra low profile fastener

24ga maximum

CONCEALOR® low profile head fasteners are engineered to perform in a variety of applications. They are specified in many metal roofing systems to attached SSR clips to metal or wood. They are easy to install and provides optimal strength.

® THE LARGEST SELECTION OF LOW THE LARGEST SELECTION OF LOW PROFILE PANCAKE HEAD SCREWSPROFILE PANCAKE HEAD SCREWS

WOOD OR THIN METALWOOD OR THIN METAL

#10, #12, & 1/4" GIMLET POINTS AND DRILL POINTS#10, #12, & 1/4" GIMLET POINTS AND DRILL POINTS

METAL APPLICATIONSMETAL APPLICATIONS

• 50% thinner head.• Special deep thread

pulls the fastener tighter.

NEED IT ULTRA LOW?NEED IT ULTRA LOW?




#12 DP4 CONCEALOR® Heavy Duty fasteners can drill and tap up to 1/4" steel! Great for heavy gauge applications requiring a low profile head. Coated with an epoxy finish that exceeds FM4470 specification assuring long-life corrosion resistance.

#3 SquareRecess Drive

#2 SquareRecess Drive

#14 DP1 CONCEALOR® is engineered to perform in a variety of applications. Special buttress thread form provides exceptional clamping loads and resists loosening compared to ordinary thread forms. Specified in many metal roofing systems to attached SSR clips over rigid insulation into metal deck. FM approved for preliminary attachment of nail base insulation without the use of stress plates.

CONCEALOR® with Buttress Thread

Ordinary Thread Form

“Flat" thread keeps the joint tight

“Tapered" thread tends to cause the

joint to loosen

Here is why we use a special thread...

FM Approved for attaching nail base; no plates

required for 1-90 uplift.

We can assemble CONCEALOR® with a bonded sealing washer that locks out weather and looks appealing!

Painting CONCEALOR® is not a problem with our Kalida-KoteTM custom paint process. We can color match to your exact requirements in 3 days or less!

Fasten into metal from 14 gauge up to 1/4"

®

#12-24 DP4 - THICK METAL#12-24 DP4 - THICK METAL

#14-13 DP1 - METAL OR WOOD#14-13 DP1 - METAL OR WOOD

SPECIAL APPLICATIONSSPECIAL APPLICATIONS

THE LARGEST SELECTION OF LOW THE LARGEST SELECTION OF LOW PROFILE PANCAKE HEAD SCREWSPROFILE PANCAKE HEAD SCREWS

Epoxy Coated 15 cycles Kesternich. Exceeds FM 4470

DescriptionAttachment Thickness Part Number

Carton Quantity

Wt Per M Pcs

#14-13 x 1-1/2” DP1 <=1.000” 141500C1 2,500 pcs 14.0#

#14-13 x 2” DP1 <=1.500” 142000C1 1,000 pcs 18.0#

#14-13 x 3” DP1 .125” - 2.500” 143000C1 1,000 pcs 26.0#

#14-13 x 4” DP1 .125” - 3.500” 144000C1 1,000 pcs 29.5#

#14-13 x 4-1/2” DP1 .625” - 4.000” 144500C1 1,000 pcs 36.5#

#14-13 x 5” DP1 1.125” - 4.500” 145000C1 1,000 pcs 40.0#

#14-13 x 6” DP1 2.125” - 5.500” 146000C1 1,000 pcs 47.0#

#14-13 x 7” DP1 3.125” - 6.500” 147000C1 500 pcs 54.0#

DescriptionAttachmentThickness Part Number

Carton Quantity

Wt Per M Pcs

#12-24 x 1-3/8” DP4 <=.375” 121375C35E 2,500 pcs 16#

#12-24 x 2-3/4” DP4 <=1.500” 122750C35E 1,000 pcs 26#

#12-24 x 3-3/4” DP4 .375” - 2.500” 123750C35E 1,000 pcs 34#

#12-24 x 4-3/4” DP4 1.375” - 3.500” 124750C35E 1,000 pcs 40#

#12-24 x 5-3/4” DP4 2.375” - 4.500” 125750C35E 1,000 pcs 48#

#12-24 x 6-3/4” DP4 3.375” - 5.500” 126750C35E 1,000 pcs 54#

#12-24 x 7-3/4” DP4 4.375” - 6.500” 127750C35E 1,000 pcs 62#

Epoxy Coated 15 cycles Kesternich. Exceeds FM 4470




#14 DP3 CONCEALOR® pancake head screws are designed for heavy gauge applications and can drill and tap up to 1/4” steel. The 1/4-14 thread produces greater strength and resists bending compared to smaller diameter screws.

These screws are coated with TRI-SEAL™ long-life coating that exceeds FM4470 specifi cation and provide 1,000-hours salt spray performance.

DescriptionAttachment Thickness Part Number

Carton Quantity

Wt Per M Pcs

A 1/4-14 x 2” DP3 1.000” Max 14200SPC3CSTS 1,000 pcs 19#

B 1/4-14 x 3” DP3 1.375” to 2.125” 14300SPC3CSTS 1,000 pcs 27#

C 1/4-14 x 4” DP3 1.625” to 3.125” 14400SPC3CSTS 500 pcs 34#

D 1/4-14 x 5” DP3 2.750” to 4.125” 14500SPC3CSTS 500 pcs 42#

E 1/4-14 x 6” DP3 3.750” to 5.125” 14600SPC3CSTS 500 pcs 50#

SPECIAL HEAD DESIGN

• 5/8” diameter head increases pullover strength and minimizes dimpling.

• #3 square recess drive provides stability during installation.

METAL ROOFCLIPS

* Exceeds tensile strength

Mechanical and Physical Properties (minimum)Thread Diameter: 1/4” (.250” nominal)Thread Pitch: 14 Material: C-1022Case Hardened per SAE J-78Tensile Strength: 4,275 lbs. Torsional Strength: 150 lbs.-in.Shear Strength: 2,600 lbs.

NAILBASE

STRUCTURAL INSULATED PANELS

ARCHITECTURALINSULATED PANELS

Pullout Strength (Ultimate Average in Pounds)

Gauge 20ga(.036”)

18ga(.048”)

16ga (.060”)

14ga(.075”)

12ga(.105”)

1/8”(.125”)

3/16”(.188”)

1/4”(.250”)

Pullout 343 533 886 1,077 2,170 2,030 3,863 *4,493

Use to attach a variety of material to steel up to 1/4” thick!

A

B

C

D

E

Choose from a variety of lengths!

Special “un-threaded” section is engineered to eliminate “jacking” when installing insulated panels!

Fasten into metal from 20 gauge up to 1/4"

Special Applications

®

1/4-14 DP3 - DRILL AND TAP UP TO 1/4" THICK STEEL1/4-14 DP3 - DRILL AND TAP UP TO 1/4" THICK STEEL

PERFORMANCE SPECIFICATIONSPERFORMANCE SPECIFICATIONS

THE LARGEST SELECTION OF LOW THE LARGEST SELECTION OF LOW PROFILE PANCAKE HEAD SCREWSPROFILE PANCAKE HEAD SCREWS





Fastener Material

Zinc Plated Steel

Screws2


Screws2



Screws



300 Series

Stainless Steel

400 Series

Stainless Steel

Unpainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesPainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesUnpainted Galvalume Steel No Yes Yes Yes Yes Yes No Yes Yes

Painted Galvalume Steel Yes4 Yes Yes Yes Yes Yes No Yes4 Yes4


®

Pullout In Wood - Average Ultimate in Pounds

Pullout In Steel - Average Ultimate in Pounds (35ksi Test Material)

FastenerDia. & Point

Material Thickness24 ga(.024”)

22 ga(.021”)

20 ga(.030”)

18 ga(.048”)

16 ga(.060”)

14 ga(.075”)

12 ga(.105”)

1/8”(.125”)

3/16”(.188”)

1/4”(.250”)

#10-16 DP3 208 267 295 503 710 968#12-14 DP3 215 292 343 555 752 1,066#12-14 DP1/Lap 261 338 390 649 890 1,259#12-24 DP4 375 500 978 1,200 2,000 3,844#14-13 DP1 338 574 720 961 1,000 1,3501/4-14 DP3 343 533 886 1,077 2,170 2,030 3,863 *4,493

FastenerDia. & Point

Wood Type1/2”

Plywood5/8”

Plywood3/4”

Plywood7/16” OSB

19/32” OSB

23/32” OSB

2 x 4 SYP

#10-13 GP 350 390 550 234 326 352 572#10-9 GP 362 396 558 235 331 358 575#12-14 DP1/Lap 376 415 598 251 351 378 550#12-14 GP 377 418 600 255 356 382 625#14-13 DP1 407 483 625 325 367 440 675

SALT SPRAY Per ASTM B117 (Hours to red rust) Carbon steel and 410 stainless steel materialsCoating Salt Spray.0002” min. (6um) zinc with clear chromate 32hrs.0003” min. (8um) zinc plating with yellow dichromate 144hrsEpoxy (ACQ Compatible) 500hrsTRI-SEAL™ Long-life Coating (ACQ Compatible) 1,000hrs

The chart to the right provides general information with regard to corrosion resistance of various plating and coatings. Contact TFC for detailed information.

Screw Tee Clip 24 ga. (Ave. Ultimate)

Zee Clip 24 ga. (Ave. Ultimate)

#10 DP3 415 lbs. 510 lbs.

#12 GP 430 lbs. 692 lbs.

#14 DP1 407 lbs. 677 lbs.

F

Decking fasteners tested with full thread embedment. 2 x 4 SYP with 1” embedment

Fastener Diameter& Material

Minimum UltimateThread

DiameterTensile (lbs.)

Shear(lbs.)

Torsional(lbs-in)

#10-9 / Carbon 0.200” 1,520 1,150 60#10-9 / 410SS 0.200” 2,500 1,625 85#10-13 / Carbon 0.195” 1,725 1,125 60#10-13 / 304SS 0.195” 1,040 701 45#10-16 / Carbon 0.186” 2,100 1,400 61#10-16 / 410SS 0.186” 3,200 2,130 92#12-14 / Carbon 0.212” 2,778 2,000 100#12-14 / 304SS 0.212” 2,630 1,978 85#12-24 / Carbon 0.213” 3,450 2,420 1101/4-14 / Carbon 0.243” 4,275 2,600 150#14-13 / Carbon 0.235” 3,620 2,500 115

DISCLAIMER: ALL DATA AND SPECIFICATIONS A R E B A S E D O N LABORATORY TESTS. APPROPRIATE SAFETY F A C T O R S S H O U L D B E U S E D B Y T H E USER OR SPECIFIER. D E T E R M I N I N G T H E PROPER FASTENER IS THE RESPONSIBILITY O F T H E U S E R O R SPECIFIER. BECAUSE A P P L I C A T I O N CONDITIONS VARY, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.

* Exceeds tensile strength

Fastening Tips• A minimum of three (3) factors of safety should be used for most self-

drilling or self-tapping fasteners. Consult a design professional for appropriate values.

• Install fastener perpendicular to the work surface and tighten to no more than approximately 70% of the torsional strength.

• Allow at least three full threads to extend beyond the material. For wood applications, allow 1” minimum embedment or full thread embedment in plywood and OSB for optimal pullout resistance.

Screwgun RPMCarbon Steel & 410SS Fasteners2,500 RPM maximum304 Stainless Steel Fasteners1,000 RPM maximumFor optimal performance, use screwguns with torque control feature. DO NOT OVER-TORQUE FASTENERS.

F

* Berridge Clips

PERFORMANCE SPECIFICATIONSPERFORMANCE SPECIFICATIONS

SALT SPRAYSALT SPRAY

Table developed by the Metal Construction Association Members (Rev. by MBMA 09.17.10)FASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CLADDINGFASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CLADDING Refer to page 16 for detailed

information on this chart.

PULLOUT LOADS PULLOUT LOADS

PULLOVERPULLOVER

TOOLINGTOOLING


Thread Type and Point

Thread Major Dia. Material Head Dia. Head

Thickness Drive Finish

#10-16 DP2 .180” C1022 .435” .080” #2 Sq/Phil .0003” Zinc & Yellow


#10-13 GP .190” C1022304 SS .450” .080” #2 Sq/Phil .0003” Zinc & Yellow

Option: TRI-SEALTM Coated Passivated

#10-16 DP3 .180” C1022304 SS .450” .080” #2 Sq/Phil .0003” Zinc & Yellow

Passivated

#10-9 GP (ULP) .200” C1022304 SS .435” .040” #2 Sq/Phil .0003” Zinc & Yellow


#12-14 GP .220” C1022304 SS .450” .080” #2 Sq/Phil .0003” Zinc & Yellow



#12-14 DP3(SD300) .210” C1022

304 SS.450”.500”

.080”

.090”#2 Sq/PhilT-25 Torx

.0003” Zinc & Yellow Option: TRI-SEALTM Coated.0003” Zinc & Clear

#12-24 DP4 .210” C1022 .425” .110” #3 Sq .001” Black Epoxy

#14-13 DP1 .238” C1022 .500” .090” #2 Sq .001” Black Epoxy

1/4-14 DP3 .245” C1022 .500” .080” #2 Sq/Phil .0003” Zinc & Yellow

FASTENER PROERTIESFASTENER PROERTIES




Triangle Fastener is pleased to introduce SPANMASTER, the first fastener designed specifically for bridge deck construction.

Through extensive research and product development, we’ve developed a fastener that reduces fastener failure, and increases productivity.

Here’s what makes SpanMaster work...

PART NUMBER141000HW3C

APPLICATIONUsed for fastening bridge decking to steel support angles.

PHYSICAL & MECHANICAL PROPERTIESDescription: 1/4-14 x 1" self-drilling fastener with radial indent under washer face.Point Type: Type 3 self-drilling point with long pilot section.Head Style: 3/8" Hex washer head. Painted RED for identification.

Material: C1018-1022 carbon steel

Heat Treatment: Case hardened to SAE J-78 specificationFinish: .0005" min mechanical zinc (Meets PENNDOT specifications)

FASTENER STRENGTH (Ultimate)Torsional: 150 inch poundsTensile: 3850 poundsShear: 2600 pounds

Pullout Strength in Steel (Ultimate in Pounds)

18 ga ( .048") -- 613 lbs16 ga (.060") -- 883 lbs14 ga (.075") -- 1148 lbs12 ga ( .105") -- 1861 lbs3/16" (.1875") -- 4553 lbs1/4" (.250") -- 5036 lbs

S PA NS PA N MASTERMASTERBRIDGE DECK FASTENER

Ordinary Fastener

Span-Master withRadial Indent

Special radial indent increases bearing surface

and distributes stress

Radius under the fastener head

concentrates stress.

SPAN-MASTER BRIDGE DECK FASTENERSSPAN-MASTER BRIDGE DECK FASTENERS




Triangle Fastener offers the most comprehensive fastener line for metal deck attachment. Special designed fasteners for side laps and structural steel up to 1/2” thick.

Our fasteners drill and tap faster and more consistently than “ordinary” self-drilling screws. Fasteners are coated to provide optimal corrosion protection, and most are ICBO approved and SDI listed!

Head Drill Drill Max MaterialDescription Style Point Capacity Thickness#10-16 x 3/4” 5/16” HWH DP3 .036” to .175” .325”#10-16 x 3/4” 5/16” HWH DP1 .018” to .095” .220”#12-14 x 3/4” 5/16” HWH DP1 .018” to .095” .205”#12-14 x 1” 5/16” HWH DP3 .036” to .210” .290”1/4-14 x 7/8” 5/16” HWH DP1 .024” to .095” .380”

Head Drill Drill Max MaterialDescription Style Point Capacity Thickness#12-24 x 7/8” 5/16” HWH DP4 .125” to .250” .325”#12-24 x 1-1/4” 5/16” HWH DP4 .125” to .250” .575”#12-24 x 1-1/4” 5/16” HWH DP5 .250” to .500” .375”1/4-14 x 1” 5/16” HWH DP3LP .036” to .250” .250”

Steel decking side laps. Special drill point for fast penetration and increased seating torque. Use a 5/16” hex nut-setter.

Steel decking to structural steel up to 1/2” thick. No need for pre-drilling. Use a 5/16” hex nut-setter.

Fasteners are ClimaSeal long-life coatedfor optimal corrosion protection!

Salt Spray (ASTM B117) :720 hrs - 10% or less red rust

Kesternich (DIN 50018, 2.0L): 25 cycles - 10% or less red rust

Corrosion ResistanceMost fasteners are available with the following approvals and listings

Factory Mutual: J.I.1. x 9A2.AM & J.I.1 x 7A2AMICBO: 3056 & ER4254City of L.A. ApprovalSteel Deck Institute Listed

Approvals & Listings

SCREWS FOR STEEL DECKING APPLICATIONSSCREWS FOR STEEL DECKING APPLICATIONS

For technical information, please refer the BLAZER® Drill Screws pages 16 & 17.




DRILL-FLEXDRILL-FLEXDUCTILE DRILL SCREWSDUCTILE DRILL SCREWS




SIZES AND SPECIFICATIONSSIZES AND SPECIFICATIONS

DRILL-FLEXDRILL-FLEXDUCTILE DRILL SCREWSDUCTILE DRILL SCREWS




Product Features• Unique double fluted point has precise cutting edges to improve drill performance in 1/4'' thru 1/2'' steel.

• Engineered for fast drilling and smooth tapping with less effort.

• Climaseal® finish provides excellent corrosion resistance and lower tapping torque.

• Attachments up to 7.2'' of material including 1/2'' steel.

• 1/4 Diameter has notched threads to reduce tapping torque.

Heavy Duty ApplicationsFirst in performance!!

Over 30 years of consistent drilling.

The original self-drillers for heavy duty applications.

Applications• Metal deck to structural steel or bar joist.

• Clips to structural steel or bar joist.

• Liner panels to structural steel or bar joist.

• Accessories to structural steel or bar joist.

• Longer length fasteners can be used in retrofit clip and sheet applications.

Corrosion Resistance Kesternich Results (DIN 50018, 2.0L) • 30 Cycles - 10% or less red rust

Salt Spray Results (ASTM B117) • 720 hours - 10% or less red rust

Corrosion ResistanceKesternich Results (DIN 50018, 2.0L) • 15 Cycles - 5% or less red rust


Selector GuideWood-to-Metal FastenersNo pre-drilling, fast, efficient attachment of wood to steel.

Applications• Plywood roof and floor sheet to steel frames.• 2 x 4 headers to steel frames.• Plywood fascia to steel frames.• Wood mansard to steel frames. Product Features

• Point has precise cutting edges to improve drill performance with less effort.

• Special winged fasteners ream a hole in wood preventing thread engagement during drilling.

• New Phillips Square Driv® and 6-Lobe drive systems provide superior installation stability and cam-out resistance.

• Wafer head design has a large bearing surface ideal for plywood.

• Flat head design countersinks and seats flush in wood.

• Gray Spex™ finish provides excellent corrosion resistance and lower tapping torque. Formulated for use in ACQ lumber!

Need a 1/4" diameter fastener to attach wood

to light gauge metal? Use our BLAZER

HEADER LG to fasten to 18 gauge or less!

See page 10.

Part Number DescriptionHead Style

Drill Point

Drill & Tap

Capacity

Max. Material

Attachment Applications

1088000B 12-24 x 7/8'' HWH #4 .125-.250 .325• Metal deck, clips, liner panels or accessories to structural steel or bar joist.

1414000 12-24 x 1-1/4'' HWH #4.5 .125-.375 .575

1006000B10700001072000

12-24 x 1-1/4''12-24 x 1-1/2''

12-24 x 2''

HWHHWHHWH

#5#5#5

.125-.500

.125-.500

.125-.500

.375

.6251.125

10740001075000164100014310001590000

1/4-28 x 3''1/4-28 x 4''1/4-28 x 5''1/4-28 x 6"1/4-28 x 8"

*HWH*HWHHWHHWHHWH

#5#5#5#5#5

.125-.500

.125-.500

.125-.500

.125-.500

.125-.500

2.1503.1504.1505.1507.150

• Longer fasteners can be used in retrofit clip and sheet applications.

Now available in small box packaging * 5/16" Across Flats HWH. All available with bonded washer.

Part Number Description Head Style

Drill Point

WoodDrill & Tap Capacity

Attachment Range Applications

107700010790001082000

10-24 x 3/4"10-24 x 1"

10-24 x 1-7/16"

WaferWaferPFH

#3#3#3

.036-.175

.036-.175

.060-.175

1/4''-3/8''1/4''-1/2''1/4''-3/4''

Plywood, mansard, fascia, roofing, flooring to steel framing.

10870001791000

10-16 x 1-13/16"10-16 x 1-13/16''

PFH**PSD Flat**

#3#3

.030-.175

.030-.1751/4''-3/4''1/4''-3/4''

Plywood, 2 x 4’s headers to steel framing.

15889101800910

#2 PSD BitT-30 Bit

1092000 17831001094000 1784100

12-24 x 2-1/4"12-24 x 2-1/4"12-24 x 2-3/4"12-24 x 2-3/4"

PFH*6-Lobe Flat*

PFH*6-Lobe Flat*

#4#4#4#4

.125-.250

.125-.250

.125-.250

.125-.250

3/4''-1-3/8''3/4''-1-3/8''3/4''-1-5/8''3/4''-1-5/8''

1096000 1785100

1/4-20 x 3"1/4-20 x 3"

PFH*6-Lobe Flat*

#4#4

.125-.250

.125-.2503/4''-2''3/4''-2''

2 x 4’s to steel framing.

*with wings **with ribs under head Now available in small box packaging.

TEKSTEKS®® CARBON CARBON SELF DRILLING FASTENERSSELF DRILLING FASTENERS




Exterior Rigid Insulation Applications

Product Features • Unique rider section stops panel jacking, point burnout and breakage.• High thread under the head prevents panel strip out.• Improved in place aesthetics.• Available in Scots® and Maxiseal® head styles.• Maximum pullover performance.• Excellent driving stability.• Seals when driven at an angle.• Fastens the broadest range of insulation thickness.• Point has precise cutting edges to improve drill performance with less effort.• Non-walking point provides fast material engagement.• Point to thread design maximizes pullout performance and minimizes back out.• Climaseal® finish provides excellent corrosion resistance and lower tapping torque.

Selector Guide

Kesternich Results (DIN 50018, 2.0L) • 30 Cycles - 10% or less red rust


Selector Guide

Application• Interior rigid and/or blanket insulation to steel frame.

Head Style• Maxiseal Hex Washer Head with Polyethylene Washer Product Features

• Large polyethylene washer prevents over driving and pullover.• Point has precise cutting edges to improve drill performance with less effort.• Non-walking point provides fast material engagement.• Point to thread design maximizes pullout performance and minimizes back out.• Fastens the broadest range of insulation.• White polyethylene washer matches insulation facers.

Part Number Description

Head Style

Drill Point

Insulation Capacity Range Applications

1033200103520010372001039200

12-14 x 1-7/8''12-14 x 2-3/8''12-14 x 3-1/4''12-14 x 4''

HWHHWHHWHHWH

#3#3#3#3

.036-.210

.036-.210

.036-.210

.036-.210

3/4'' to 1'' 1-1/8' to 1-1/2''1-5/8'' to 2-3/8''2-1/8'' to 3''

• Interior Rigid Insulation to Steel Frame


Head Style

Drill Point

Insulation Capacity Range Applications

Maxiseal® • Roof and wall panel over rigid insulation to steel framing.

1034000103600010380001040000

12-14 x 1-7/8"12-14 x 2-3/8"12-14 x 3-1/4"12-14 x 4"

HWHHWHHWHHWH

#3#3#3#3

.036 - .210

.036 - .210

.036 - .210

.036 - .210

3/4" to 1" 1-1/8" to 1-1/2" 1-5/8" to 2-3/8"

2-1/8" to 3"

Scots® • Roof panel over spacer block and insulation to eave purlin.

1169200117020011712001172200

12-14 x 1-7/8"12-14 x 2-3/8"12-14 x 3-1/4"12-14 x 4"

HWHHWHHWHHWH

#3#3#3#3

.036 - .210

.036 - .210

.036 - .210

.036 - .210

3/4" to 1" 1-1/8" to 1-1/2" 1-5/8" to 2-3/8"

2-1/8" to 3"

RIGID INSULATION ATTACHMENTRIGID INSULATION ATTACHMENTTEKSTEKS®® SELF DRILLING FASTENERS SELF DRILLING FASTENERS

Scots HeadHead StylesMaxiseal Head

The original self-drilling fasteners designed specifically for rigid insulation.

The only self-driller designed for this unique application.

Interior Insulation Fasteners




Scots 300 Stainless Steel will never rust...ever!!!

• For improved appearance and extra life an integral design controls the EPDM washer.

• Combines 300 series stainless steel exterior with the strength of carbon steel.

• 300 series stainless most preferred for galvalume long life panels.

• Point has precise cutting edges to improve drill performance with less effort.

• Non-walking point provides fast material engagement.

• Point to thread design maximizes pullout performance and minimizes back out.

Applications • Panel over blanket insulation to steel frame.• Roof curb to structural steel.• Standing seam roof system end-laps. • Stitch roof and wall side-laps. • #17 diameter replacement screw for #12 and 1/4 diameter screws.

Selector Guide

Selector Guide

• HTZ fasteners have the highest torsional head strength values in the industry ... no head failures.• Zinc aluminum alloy head gives premium corrosion resistance ... no red rust.• "No mar™" radius washer design will not scratch, pierce or damage panels if over driven.• For improved appearance and extra life an integral design controls the EPDM washer ... Maximum sealing protection.

• Point has precise cutting edges to improve drill performance with less effort.• Non-walking point provides fast material engagement.• Point-to-thread design maximizes pullout performance and minimizes back out.• Drills and taps in the broadest range of applications.

Product Specifications

Diameter . . . . #12, 14Thread Form. . 12-14, 1/4-14Point Type . . . Teks 1, Teks 2, . . . . . . . . . . . . Type ABFinish . . . . . . . Silver Climaseal® . . . . . . . . . . . . Head Paint . . . . . . . . . . . . available

Head Styles5/16'' HWH zinc-aluminum alloy with integral washer design.

Product Features


Head Style

Drill Point

Drill & Tap Capacity

Max. Material


116525311672531168253

12-14 x 1''12-14 x 1-1/4''12-14 x 1-1/2''

HWHHWHHWH

#2#2#2

.036-.210

.036-.210

.036-.210

.310

.560

.790

• Panel over blanket insulation to steel frame.

11630001788000

12-24 x 2''12-24 x 4"

HWHHWH

#5#5

.125-.500

.125-.5001.0003.000

• Roof curb to structural steel.

13872531175153

1/4-14 x 7/8''1/4-14 x 1-1/8''

HWHHWH

#1#1

.018-.095

.018-.095.320.395

• Stitch roof and wall sidelaps.• SR endlaps.• Standing seam roof system endlaps.

1616000 1/4-14 x 1-1/4''

HWH #3 .036-.210 .630

1178253 1701000

1/4-14 x 3/4''1/4-14 x 1-1/2''

HWHHWH

ABAB

--

.435

.870• Replacement screw for 12 and 1/4'' diameter fasteners

11802251625053

17-14 x 1'17-14 x 1-1/4'

HWHHWH

ABAB

--

.686

.935


Head Style

Drill Point

Drill & Tap Capacity

Max. Material


172705317250531729053

12-14 x 1''12-14 x 1-1/4''12-14 x 1-1/2''

HWHHWHHWH

Teks/2Teks/2Teks/2

.036-.210

.036-.210

.036-.210

.310

.560

.790

• Panel over blanket to steel frame

1721053 1/4-14 x 7/8''

HWH Teks/1 .024-.095 .320 • Stitch roof and wall side laps

1723053 1/4-14 x 1-1/4''

HWH Teks/2 .036-.210 .630 • Panel over blanket to steel frame.• Standing seam roof system end-laps.

1736053 1/4-14 x 1''' HWH Type AB

------------- .686 • Replacement screw for 12 diameter fasteners.• Panel over blanket to steel frame in pre-drilled applications.

LONG-LIFE TEKS FASTENERSLONG-LIFE TEKS FASTENERS

HTZ™ High Torque Zinc™ Long Life TeksHTZ™ High Torque Zinc™ Long Life Teks®® Fasteners Fasteners

SCOTS Stainless Cap Head FastenersSCOTS Stainless Cap Head Fasteners




Pullout Values (average lbs. ultimate)

Fastener values

Sheet Steel Gauges

Shear Values (average lbs. ultimate)

Gauge No. 12 14 16 18 20 22 24 26

Decimal Equivalent

.105" .075" .060" .048" .036" .030" .024" .018"

Fastener(dia-tpi)

Tensile(lbs.-min.)

Shear(avg. lbs. ult.)

Torque(min. in. lbs.)

TEKS® Heavy Duty

12-24 T-412-24 T/4.512-24 T/51/4-28 T/5

3020316531885577

2100220022003310

100150150234

TEKS® Wood To Metal Fasteners

10-1610-2412-241/4-20

1936270231653860

1400150022002700

6165150168

TEKS® Interior and Exterior Fasteners

12-14 2778 2000 90

MAXISEAL™, SCOTS, HTZ

10-1612-1412-24 T/412-24 T/51/4-14

19362778302031884060

14002000210022002600

6192100150150

Dia. Pt. 26 24 22 20 18 16 14 12 3/16 1/4

TEKS® Heavy Duty

Fastener Steel Gauge

124

4.55

---

---

153215081527

348538653701

401341013999

1/4 5 - - 1507 3300 5059



#10-16 3 - 208 266 299 499 708 967 1474 - -

#12 4 - - - - - 683 923 1508 3865 4101

1/4 4 - - - - - 788 1116 1803 4297 -



12 3 142 211 289 341 551 757 1063 1631 2998



10 3 124 208 266 299 499 708 967 1474 - -

12 2345

156142

--

243211

--

283289

--

375341

--

605551

--

848757697

-

11811063986

-

1856163115321527

3520299834853701

--

40133999

1/4 13

AB

208141235

329231365

428293496

562346597

800613702

1151880926

-11451180

185816901716

455034463523

---

17 AB 225 261 350 442 553 752 1122 - - -

Dia. Pt. 26 24 22 20 18 16 14 12 3/16 1/4

TEKS® Heavy Duty

Fastener Steel Gauge (lapped)

124

4.55

---

---

204826412650

203028872700

-28972762

1/4 5 1597 2005 2350 2792 3310



#10-16 3 728 1266 1540 1522 - -

#12 4 - - - - 2148 2030

1/4 4 - - - - 2650 2820



12 3 - - - 769 1358 1620 1970 1986



#10 3 - 445 526 728 1266 1540 1552 -

#12 2345

365---

600---

623---

898769

--

13701358

-

-

17581620

--

21381970

--

-198620482650

1/4 13

AB

511-

422

849-

482

885-

669

1244930889

176514421157

-2100

-

-2584

-

-2650

-

#17 AB 459 745 989 958 1415 - - -





ZAC ZINC HEAD FASTENERSZAC ZINC HEAD FASTENERS

Call TFC for all the latest sizes and types of long life fasteners for commercial roofing!

Size TypeINTEC Part

No.

Pcs. Per Std. Carton

Weight Lbs. Per M

Pcs.

12 x 3/4''14 x 3/4''14 x 1''14 x 1"14 x 1-1/2"14 x 2"14 x 2-1/2"

Sharp PointAB

M/P AM/P ABM/P ABM/P ABM/P AB

A1653-FLA4365-FMA3325-FMA4395-FMA4485-FMA4513-FMA4510-FM

2500250020002000200015001500

19.124.525.024.628.232.837.6

17 x 1''17 x 1-1/2"

ABAB

A6045-LFA6066-LF

20001500

24.129.9

12-14 x 1''12-14 x 1-1/4"12-14 x 1-1/2"12-14 x 2"12-14 x 2-1/2"12-14 x 3"

Impax S/DImpax S/DImpax S/DImpax S/DImpax S/DImpax S/D

S4576-FLS4631-FLS4676-FLS4776-FLS4901-FLS4951-FL

200020001500100015001250

21.523.825.529.732.636.2

1/4-14 x 7/8"1/4-14 x 1-1/4''1/4-14 x 1-1/2"

Lap Impax#2 Self-Drill#2 Self-Drill

S5065-FMS5195-FMS5287-FM

200020001500

21.728.631.2

12-24 x 1-1/4"12-24 x 1-1/4"12-24 x 1-1/2"

Impax 45Impax 5Impax 5

S4665-FLS4669-FLS4742-FL

200015001500

24.328.727.5




• Type AB point and self-tapping thread• Available in carbon steel or stainless steel• Hex washer head or Torx® truss head• Bonded Weath-R-Seal® washer• High-quality, tapping lead threads ease installation• Larger-than-standard diameter provides additional shear strength• Type AB point, assembled with bonded Weath-R-Seal® washer

SCRU-BOLT® FASTENERSTo ease the installation of standing seam roofs Scru-Bolt® fasteners are self-tapping screws developed with Butler® Manufacturing for attaching standing seam roofing panel clips to pre-punched framing members, or attaching panels to secondary structural members.

DiameterWasher

Size Head Style Wt./MCarbon Steel23/64" x 1" .729" Hex Washer 3223/64" x 1-1/4" .729" Hex Washer 3723/64" x 2" .729" Hex Washer 5523/64" x 2-1/4" .729" Hex Washer 6023/64" x 2-3/4" .729" Hex Washer 7023/64" x 3-1/2" .729" Hex Washer 8823/64" x 5" .729" Hex Washer 12123/64" x 6" .729" Hex Washer 14411/32" x 7/8" 9/32" Torx® Truss 2611/32" 1-1/2" 9/32" Torx® Truss 3811/32" x 2" 9/32" Torx® Truss 48410 Stainless Steel11/32" x 7/8" .729" Hex Washer 2611/32" x 1-1/4" .729" Hex Washer 3211/32" x 2-3/4" 1" Hex Washer 6123/64" x 1" .729" Hex Washer 31Scru-Bolt Nut11/32" - 12 n/a n/a 6

Explosion Venting Fasteners Limit damage from industrial or agricultural explosions.

A series of collapsible washers on stainless steel fasteners designed to minimize injury and destruction of property from explosions caused by agricultural or industrial operations.

Normal Installed Condition Interior Explosion Release Conditions

Panel

Centeringdevice

Framingmember

Panel separates

from framing

member

Fabco® aluminum pressure-

release washer

deforms

Explosive

force

#14 Fabco® Vent-All Fastening System

featuring aluminum pressure-release

washer

It is suggested that all sheets or panels be provided with restraint cables, about three feet long, anchored to the structure to prevent sheets from becoming flying projectiles.

Contact TFC for information

Washer Designation Color Code

Release Value per Fastener

EXA-74 Green 70#EXA-76 Blue 110#EXA-79 Tan 175#EXA-84 Light Green 435#EXA-19 Light Blue 885#

• Maintains standard building integrity• Minimizes destruction from explosion

by quickly dissipating explosive forces.• May be used with any sheet or panel,

with or without insulation, in field assembled or shop-assembled walls.

• .729" O.D. washer with special aluminum alloy bonded with EPDM or neoprene sealant.

• Stainless steel machine screws.• Washers designed to collapse under

force of explosion, allowing panel to separate and vent shock waves.

How do you calculate the release value?1. Determine area to be vented. 2. Apply desired release pressure per square foot to the area being vented.3. Divide by desired number of fasteners per structural location to determine explosion venting washer.

SELF-TAPPING SCREWSSELF-TAPPING SCREWS




• 304 Stainless Steel for optimalcorrosion resistance

• Assembled with 15MM O.D. Stainless Steel BOND-SEALER washer provides excellent seal in harsh environments.

• Special plating on Type AB and B to minimize thread rollover.• Preferred fastener for ACQ treated

lumber applications.

#14-10 TYPE ALength Box Qty Wgt. / M

3/4” 2,500 10.8

1” 2,500 14.2

1-1/2” 1,500 19.1

2” 1,000 23.4

2-1/2” 1,000 28.1

3” 500 34.1

4” 500 45.5

5” 300 52.8

1/4-14 TYPE ABLength Box Qty Wgt. / M

3/4” 2,500 12.5

1” 2,500 14.9

1-1/2” 1,500 19.7

#17-14 TYPE AB

Length Box Qty Wgt / M

1” 2,000 18.9

1/4-14 TYPE BLength Box Qty Wgt / M

1” 2,500 14.1

1-1/2” 1,500 19.5

2” 1,000 23.1

2-1/2” 1,000 29.0

3” 500 33.3

4” 500 43.4

5” 300 53.5

6” 250 62.2

We stock the largest selection of lengths in the industry!

Triangle Fastener Corporation stocks a full line of 304 stainless steel tapping screws for a variety of applications.

Our 304 stainless steel tapping screws provide exceptional corrosion resistance, ductility and high strength. We coat our type AB & B screws with a special plating to minimize thread rollover when tapping high tensile steel.

We can also supply the correct drill bits and power tools to assure proper fastening.

You want’em...we got‘em!

Contact TFC...When you “NEED-IT-NOW!”

Refer to the back for technicalinformation and drill bit size

1/4-14 TYPE BApplication14ga to 1/2”

#14-10 TYPE AApplication

Up to 14ga & Wood

#17-14 TYPE ABApplicationUp to 10ga

304 STAINLESS STEEL 304 STAINLESS STEEL SELF-TAPPING SCREWSSELF-TAPPING SCREWS

1/4-14 TYPE ABApplication

Up to 1/2” & Wood

NEED A BACK-OUT RESISTANT TAPPING SCREW?Specify our carbon steel #17 x 1" Type AB with VRT® Technology. It produces 3-1/2 times more back-out resistance than a standard thread. Supplied with TRI-SEAL™ long life coating.




PRODUCT: TFC Tapping Screws (ANSI B18.6.4 , AC 118)

MATERIAL: 304 Stainless SteelMATERIAL PROPERTIES Cold Worked Tensile: 103,000 psi min. Yield: 86,000 psi min. Slightly magnetic after cold worked.FINISH Type B : .0003” Min. Cad PlatingType A & AB : .0003” Min. Zinc PlatingSalt Spray: >2,000 hrs no red rust

APPLICATIONS: Type 304/304L stainless may be considered for use in a wide range of food processing, dairy and dyeing industry applications such as pipelines, buckets, sterilizers and other types of preparation and processing equipment.

CORROSION RESISTANCE: Annealed Project 70+ Type 304/304L stainless has proven to be resistant to atmospheric corrosion, foodstuffs, sterilizing solu-tions, many organic chemicals and dyestuffs, and a wide variety of inorganic chemicals.

Important Note: The following 5-level rating scale is intended for comparative purposes only. Corrosion testing is recommended; factors which affect corrosion resistance include temperature, concentration, pH, impurities, aeration, velocity, crevices, deposits, metallurgical condition, stress, surface fi nish and dissimilar metal contact.

Environment Corrosion Resistance

Nitric Acid Good

Sulfuric Acid Moderate

Phosphoric Acid Moderate

Acetic Acid Moderate

Sodium Hydroxide Moderate

Salt Spray (NaCl) Good

Sea Water Restricted

Sour Oil/Gas Moderate

Humidity Excellent

INSTALLATION INFORMATION

DRILL BITSUse 135o split point drill bits for optimal performance.

HEAD STYLE3/8” Indented Hex HeadSEALING WASHER 15MM O.D. 304 Stainless Steel vulcanized to EPDM.

Fasteners can be painted to match your specifi c color. Fasteners can be painted to match your specifi c color. Contact TFC for pricing and availability.Contact TFC for pricing and availability.

#14-10 Type A1/4-14 Type AB & B

SteelThickness

Point Types

Drill Bit

26ga (.018”) A, AB 1/8”24ga (.024”) A, AB 1/8”22ga (.030”) A, AB 5/32”20ga (.036”) A, AB 3/16”18ga (.048”) A, AB 3/16”16ga (.060”) A, AB, B #1014ga (.075”) A, AB, B #812ga (.105”) A, AB, B #81/8” (.125”) A, AB, B #810ga (.134”) AB, B #83/16” (.187”) AB, B #11/4” (.250”) AB, B #13/8” (.375”) AB, B #11/2” (.500”) AB, B #1

#17-14 Type ABSteel

ThicknessPoint Type

Drill Bit

26ga (.018”) AB 3/16”24ga (.024”) AB 3/16”22ga (.030”) AB 3/16”20ga (.036”) AB 3/16”18ga (.048”) AB 1/4”16ga (.060”) AB 1/4”14ga (.075”) AB 1/4”12ga (.105”) AB 1/4”1/8” (.125”) AB 1/4”10ga (.134”) AB 1/4”

DISCLAIMER: ALL TEST RESULTS AND FASTENER RECOMMENDATIONS ARE BASED ON LABORATORY CONDITIONS. BECAUSE ACTUAL JOB SITE CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC. WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.

PULLOUTAverage Ultimate - Pounds

SteelThickness

#14-10 Type A

1/4-14Type AB & B

#17-14Type AB

26ga (.018”) 270 216 41024ga (.024”) 363 34422ga (.030”) 363 34420ga (.036”) 459 411 52218ga (.048”) 657 54116ga (.060”) 1,194 686 80514ga (.075”) 1,368 983 99612ga (.105”) 1,780 1,6981/8” (.125”) 1,812 2,24210ga (.134”) 2,8553/16” (.187”) 2,6931/4” (.250”) 3,6955/16” (.312”) 3,7463/8” (.375”) 3,7841/2” (.500”) 3,790

1/4-14 TYPE BApplication14ga to 1/2”

1/4-14 TYPE ABApplication

Up to 1/2” & Wood

#14-10 TYPE AApplication

Up to 14ga & Wood

#17-14 TYPE ABApplicationUp to 10ga

SCREWGUN SPEED: 1,000 rpm maximum

NOTE: Applications and corrosion resistance information taken from Carpenter Technologies ALLOY DATA sheet.Copyright 2005 CRS Holdings Inc. All rights reserved.

Screw TypeNominal

Dia. Torsional Tensile Shear

#14-10 TYPE A .250” 125 in-lb 2,925 lbs. 1,925 lbs.

1/4-14TYPE AB .245” 150 in-lb 3,700 lbs. 2,800 lbs.

1/4-14TYPE B .245” 150 in-lb 3,700 lbs. 2,800 lbs.

#17-14TYPE AB .285” 170 in-lb 5,200 lbs. 3,125 lbs.

MECHANICAL PROPERTIES

FASTENER DATA AND SUBMITTAL SHEET

304 STAINLESS STEEL 304 STAINLESS STEEL SELF-TAPPING SCREWSSELF-TAPPING SCREWS




Choose from the largest selection of fasteners for metal-to-wood applicationsDesigned for fast installation and corrosion free performance.All fasteners can be painted with our Kalida-Kote paint finish to your exact color match. Polyurethane with UV protection provides a chip resistant finish without chalking and fading.

#9-15 Double Lead ThreadEconomical Sharp gimlet point for fast penetration.

#10-15 Dual Threadwith Type 17 PointDual thread form for increased pullout load. The special milled point penetrates high tensile steel panels!

Available in 410 Stainless Steel for ACQ lumber applications.

PANEL-TITE® #14 High Performance#14 high strength for extra tough applications!

STAINLESS STEEL Cap Head

ZINC ALLOY Cap Head

305 STAINLESS STEEL Attaching steel to wood? Choose Bi-metal screw with carbon steel tip Attaching aluminum to wood: Choose all stainless

Size Attachment Range

#9-15 x 1" Gimlet#9-15 x 1-1/2" Gimlet#9-15 x 2" Gimlet#9-15 x 2-1/2" Gimlet#9-15 x 3" Gimlet

<.250<.750.500 to 1.2501.000 to 1.7501.500 to 2.250


#10-15 x 1" Type 17#10-15 x 1-1/2" Type 17#10-15 x 2" Type 17#10-15 x 2-1/2" Type 17#10-15 x 3" Type 17

<.250m<.750.500 to 1.2501.000 to 1.7501.500 to 2.250


#12-11 x 3/4" Gimlet Stitching - Panel Lap


#14-10 x 1" Type S point#14-10 x 1-1/2" Type S point#14-10 x 2" Type S point

<.250<.750.500 to 1.250

Options

Sizes

METAL-TO-WOOD FASTENERSMETAL-TO-WOOD FASTENERSPANEL-TITEMETAL-TO-WOOD SCREWS

R

PANEL-TITE®#10-12 Double Lead Choose this double lead thread for superior strength.TRI-SEAL coated is formulated for ACQ lumber applications. 1,000 hrs salt spray!

Available with a stainless cap head and 304 stainless steel!

PANEL-TITE® #12-11 Double Lead Lap Screw #12 Sharp point for fast penetration into panel laps.

Available with a stainless cap head.

PANEL-TITE® ULTRA12#12-8 Low Root This high strength fastener is designed to provide superior pullout. TRI-SEAL coated is formulated for ACQ lumber applications. 1,000 hrs salt spray!

High performance!

High performance!

Need more corrosion protection?Select either the stainless head, zinc head or stainless steel threads.

Contact TFC for sizes and availability.


#10-12 x 1" Gimlet#10-12 x 1-1/2" Gimlet#10-12 x 2" Gimlet #10-12 x 2-1/2" Gimlet#10-12 x 3" Gimlet

<.250m<.750.500 to 1.2501.000 to 1.7501.500 to 2.250


#12-8 x 1" Gimlet#12-8 x 1-1/2" Gimlet#12-8 x 2" Gimlet

<.250<.750.500 to 1.250




Material: Carbon SteelPlating#10-12 & #12-11 PANEL-TITE®: TRI-SEAL Long-life (ACQ Compatible)#9-15, #10-15 & #14-10 : .0005" Min. Zinc

Material: 304 Stainless SteelFinish: Passivated. (ACQ Compatible)

Material: 304 Stainless Steel Bi-MetalPlating: TRI-SEAL (ACQ Compatible)

Material: 410 Stainless SteelPlating: OxySeal (ACQ Compatible)

#12-11 Lap

Pullout Values in Wood (Carbon Steel or Stainless Steel)

Strengths (Carbon Steel) Pullover Strength in Pounds

Corrosion Test Results

#12-8 Low Root

#10-15Dual Thread

#9-15Double Lead

#14-10Type S Point

SizeTensile

(lbs. min)Shear

(avg. lbs. ult.)Torsional

(min. in. lbs.)#9-15 1,800 1,200 50#10-15 1,850 1,216 65#10-12 2,100 1,400 65#12-8 2,183 1,946 80#12-11 2,778 2,000 92#14-10 3,150 2,150 125

Pullout In Pounds

Material #9-15 #10-15 #10-12 #12-8 #14 Embd Depth2x Pine 328 3/4"

572 580 580 625 650 1"1/2" CDX 225 230 230 384 384 full5/8" CDX 328 340 340 446 489 full3/4" CDX 476 480 480 587 667 full7/16" OSB 183 250 234 251 245 full19/32" OSB 276 326 456 365 full23/32" OSB 261 352 524 406 full

Washer Size26ga

(.019")24ga

(.023")22ga

(.031")20ga

(.035")18ga

(.049")1/2" O.D. 515 674 875 1100 16279/16" O.D. 587 744 915 993 124615mm O.D. 564 810 1097 1166 1643

TRI-SEAL #9 and #14Kesternich 30 cycles 5 cyclesSalt Spray 1,000 hours 48 hours

TECHNICAL DATA SHEET TECHNICAL DATA SHEET

PaintKalida-Kote Polyurethane with UV stabilizer

PANEL-TITEMETAL-TO-WOOD SCREWS

R

#10-12 Double Lead

Material Specifi cations

Performance Specifi cations

Sizes

DISCLAIMER: ALL TEST RESULTS AND FASTENER RECOMMENDATIONS ARE BASED ON LABORATORY CONDITIONS. BECAUSE ACTUAL JOB SITE CONDITIONS VARY AND ARE UNCONTROLLABLE BY TFC. WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.




SCREWS FOR SUPERIOR CORROSION SCREWS FOR SUPERIOR CORROSION RESISTANCE & LONG-LIFE PERFORMANCERESISTANCE & LONG-LIFE PERFORMANCE

Description Drilling Thickness Part No. Carton

QuantityE #9-15 x 1” GP .040 AL DD9100PW3SS 3,000 pcs.F #9-15 x 1-1/2” GP .040 AL DD9150PW3SS 2,500 pcs.G #9-15 x 2” GP .040 AL DD9200PW3SS 2,000 pcs.H #9-15 x 2-1/2” GP .040 AL DD9250PW3SS 1,500 pcs.

SIZES SIZES

EA

B

C

D

Description Drilling Thickness Part No. Carton

QuantityA #10-12 x 1” GP 20ga. max 10100HWGSYSWSC 2,500 pcs.B #10-12 x 1-1/2” GP 20ga. max 10150HWGSYSWSC 2,000 pcs.C #10-12 x 2” GP 20ga. max 10200HWGSYSWSC 2,000 pcs.D #10-12 x 2-1/2” GP 20ga. max 10250HWGSYSWSC 1,000 pcs.

Diameter & Point: #9-15 Gimlet PointMaterial: 305 Stainless SteelPlating: Passivated Head Style: 1/4” HWHThread: #9-15 Double Lead

PANEL-TITE® SS Stainless Steel w/ Aluminum Bonded-Sealer Washer

PANEL-TITE® SCHStainless Cap Headw/ Flange Sealer

Diameter & Point: #10-12 Gimlet PointMaterial: Carbon Steel Shank, 304 Stainless Steel Cap HeadPlating: TRI-SEALTM CoatingHead Style: 1/4” HWHThread: #10-12 Double LeadSalt Spray: 1,000 hrs.

SIZES SIZES

We offer a complete line of metal-to-wood screws that provide superior corrosion protection in the most harsh environments.

Choose either the PANEL-TITE® with stainless steel cap head or all stainless steel for attaching aluminum panels to wood.

• Use on 20yr warranty roof systems.• Carbon steel shank with TRI-SEALTM coating.• Provides outstanding corrosion protection.

A

MATERIAL AND PHYSICAL PROPERTIESMATERIAL AND PHYSICAL PROPERTIESFASTENER STRENGTHFASTENER STRENGTH

TECHNICAL DATA

PULLOUTPULLOUTMaterial Type & Thickness

Embedment Depth

Pullout Load (Ult Avg.)#9-15 #10-12

1/2” Plywood Full 225 lbs. 230 lbs.5/8” Plywood Full 328 lbs. 340 lbs.3/4” Plywood Full 476 lbs. 480 lbs.2X - SYP Treated 1” 572 lbs. 580 lbs.2X - SYP Construction 1” 492 lbs. 502 lbs.

Size Tensile (lbs.)

Shear(lbs.)

Torsional(Inch-lbs.)

#9-15 1,500 980 50#10-12 2,100 1,400 65

• 305 stainless steel.• Used in aluminum applications.• Preferred screw for ACQ lumber.

DISCLAIMER: ALL DATA AND SPECIFICATIONS ARE BASED ON LABORATORY TESTS. APPROPRIATE SAFETY FACTORS SHOULD BE USED BY THE USER OR SPECIFIER. DETERMINING THE PROPER FASTENER IS THE RESPONSIBILITY OF THE USER OR SPECIFIER. BECAUSE APPLICATION CONDITIONS VARY, WE ASSUME NO LIABILITY FOR THE USE OF THIS INFORMATION.

F

G

H

E

PANEL-TITEMETAL-TO-WOOD SCREWS

R




SIZES

Coarse Thread - TRI-SEAL COATED• Exterior wood screw for outdoor applications including desks,

treated wood, patios and fencing.• TRI-SEAL coated formulated for ACQ treated lumber!

305 Stainless Steel• 305 stainless steel coarse thread deck screw, #2 square drive, type 17 point.• Exterior wood screw for outdoor applications including desks, treated wood, patios

and fencing applications that require a high degree of corrosion resistance.• For best possible corrosion resistance in ACQ Treated Lumber!• Type 17 point provides superior penetration through the hardest of woods.• 305 stainless steel provides maximum strength with superior corrosion protection.

Full line of high performance wood deck fasteners

Composite Deck Screws - COATED•For flush mounting of the fasteners without mushrooming!SIZE: #10 x 2-3/4"

Ordinary Bugle Head Seats Flush

SizeCarton

QuantityDrive Style

Carton Weight (lbs.)

6 x 1" 10M + 326 x 1-1/4" 8M +/ 306 x 1-5/8" 5M +/ 246 x 2" 3.5M +/ 218 x 2-1/2" 2.5M +/ 248 x 3" 2M +/ 2410 x 3-1/2" 1.5M +/ 2810 x 4" 1M +/ 2410 x 5" 1M + 2710 x 6" 1M + 30

SizeCarton

QuantityCarton

Weight (lbs.)8 x 1-1/4" 5M 288 x 1-5/8" 4M 298 x 2" 3M 2510 x 2-1/2" 2M 2510 x 3" 1.5M 2310 x 3-1/2" 1M 18

Dec-KingExterior Wood Screws

Corrosion ResistanceKesternich Results (DIN 50018, 2.0L)• 25 Cycles - 10% or less red rust

Salt Spray Results (ASTM B117)• 1000 hours - 10% or less red rust

Product FeaturesCoated with Climacoat® for maximum resistance to corrosion, staining and streaking inside the lumber and on the deck.

Approved for use is ACQ treated lumber.

Outperforms all zinc based platings in treated wood.

Pullout strength is superior over nails.

Eliminates wood splitting, nail pops, hammer marks and bent nails.

Now available in both #2 Phillips and #2 Square Drive.

Selector Guide

Performance DataPullout Values (average pounds ultimate) Embedment 2'' x 4'' Stud Grade S.Y. Pine

Note: The values listed are ultimate averages achieved under laboratory conditions. An appropriate safety factor should be applied in these values to achieve a design value.

Description Head StylePart

Number Applications6 x 1-1/4" #2 Phillips Bugle 2176500 1" x 4" or 1" x 6" Base Trim; Lattice6 x 1-5/8" #2 Phillips Bugle 2136500 1" x 4" or 1" x 6" Base Trim; Ballisters; Lattice

7 x 2" #2 Phillips Bugle 2138500 5/4" x 4" or 5/4" x 6"1" x 4" or 1" x 6"

Radius Edfed Decking; Base Trim; Ballisters; Lattice

8 x 2-1/2" #2 Phillips Bugle 2140500 5/4" x 4" or 5/4" x 6"2" x 4" or 2" x 6"2" x 6" or 2" x 8"

Radius Edged Decking Decking Rail Cap or Base Trim

8 x 3" #2 Phillips Bugle 2141500 2" x 4" or 2" x 6"2" x 6" or 2" x 8"

Decking Rail Cap or Base Trim

10 x 3-1/2" #2 Phillips Bugle 2142500 2" x 4" or 2" x 6"2" x 6" or 2" x 8"

Decking Rail Cap or Base Trim

Description 1/2" 3/4" 1" 1-1/4"6 x 1-1/4" 182 329 422 -6 x 1-5/8" 182 329 422 620

7 x 2" 189 318 440 630

8 x 2-1/2" 186 290 502 630

8 x 3" 186 290 502 645

10 x 3-1/2" 241 386 522 721

WOOD DECK FASTENERSWOOD DECK FASTENERS

305 Stainless Steel

Carbon Steel




Flat Recex® Lo-Root® Wood ScrewHardened Steel

Lubricized (2001)

Flat Recex® Lo-Root®

Wood Screw (Special #2 Drive)Hardened Steel

Lubricized (2001)

Selector Guide

Selector Guide

The MaxxFlat Recex® Lo-Root® Wood Screw with NibsSelf-Drilling, Self-CountersinkingType 17 Hardened Steel

Lube (2001) • Ultra Seal (3401) • Black Phosphate (6001)Dacromet (6501) • Minimum Plating Charge May Apply

Selector Guide

Round Washer Recex®

Lo-Root® Wood ScrewHardened Steel

Diameter Lengths Carton Quantity

8 1/2, 5/8 12M 3/4 10M 7/8, 1 8M 1 1/8, 1 1/4 6M 1 3/8,1 1/2 5M 1 3/4 4M 2 3M 2 1/4, 2 1/2 2M 2 3/4, 3 1.5M10 1/2 10M 5/8, 3/4 8M 1 6M 1 1 /4 5M 1 1/2, 1 3/4 3M 2 2.5M 2 1/2 1.5M 3 1M

Lubricized (2001)

Selector Guide

Pan Recex® Lo-Root®

Wood Screw, Hardened Steel

Lubricized (2001)

Selector Guide

Fasteners designed for the furniture industry and multipurpose construction fastening.


5 1/2 , 5/8 15M

6 1/2, 5/8, 3/41

1-1/41-1/2

15M10M8M7M

8 5/8, 3/41

1-1/81-1/4

1-3/8, 1-1/21-3/4

22-1/42-1/22-3/4

3, 3-1/4

15M10M8M

7.5M5M4M

3.5M3M

2.5M2M

1.5M

10 3/41

1-1/41-1/21-3/4

22-1/4, 2-1/2

3

10M8M5M4M3M

2.5M2M

1.5M


6 3/8, 1/2, 5/8, 3/4 15M

8 5/87/8, 1

1-1/8, 1-1/42

12M8M6M3M

10 5/8 8M


66666

1/2, 5/8, 3/41

1-1/41-1/21-3/4

15M10M8M7M5M


8 11-1/81-1/41-3/81-1/21-3/4

22-1/4, 2-1/2, 2-3/4"

3

10M8M

7.5M5M5M4M

3.5M2.5M1.5M

FASTENERS FOR WOODFASTENERS FOR WOOD




Flat Robertson® Lo-Root®Wood Screw (“The Original")Hardened Steel

Lubricized (2001)

Selector Guide

Pan Robertson®

Type AHardened Steel

Lubricized (2001)

Selector Guide

Pan Robertson®

(Special #2 Drive)Type 17 (with 5/8" Thread)Face Frame Screws

Lubricized (2001)

Selector Guide

Lubricized (2001)

Selector Guide

Round Washer Recex®

with Extra Large Washer(.420-.440 head diameter)For Drawer Fronts

Selector Guide

Truss Recex® Lo-Root® Wood Screw(Special #2 Drive) Type 17 Hardened Steel

Lubricized (2001)


6 1/2 , 3/41

1-1/41-1/2

15M10M7.5M6M

8 1/25/83/41

1-1/41-1/21-3/4

2

15M12M10M8M6M5M4M3M

10 3/41

1-1/41-1/21-3/4

2

8M6M5M3M3M

2.5M

12 11-1/41-1/2

4M3M

2.5M


6 1-1/41-1/2

7.5M6M


6 3/8, 1/2, 5/8, 3/4 15M


8 1-1/8, 1-1/4 5M


8 3/41

1-1/41-1/21-3/4

22-1/42-1/2

3

15M10M7.5M5M4M

3.5M3M

2.5M1.5M

10 1-1/41-1/21-3/4

22-1/2

3

5M4M3M

2.5M2M

1.5M





Sizes

Wood Screw Flat Head PhillipsAvailable in Carbon and Stainless Steel

Sizes

Tapping Screw Pan Head PhillipsAvailable in Carbon and Stainless Steel

Sizes

Tapping Screw Indented Hex Washer Head SlottedAvailable in Carbon and Stainless Steel

Diameter Lengths

#2 1/4, 3/8, 1/2, 5/8, 3/4

#3 1/4, 3/8, 1/2, 5/8, 3/4

#4 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2

#5 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2

#6 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2

#7 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2

#8 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2, 3, 3-1/2, 4

#9 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2, 3

#10 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2, 3, 3-1/2, 4

#12 1/2, 3/4, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/4, 2-1/2, 3, 3-1/2, 4

Diameter Lengths

#4 1/4, 3/8, 1/2, 5/8, 3/4, 1

#6 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 2

#7 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2

#8 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#10 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#12 3/8, 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#14 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

Diameter Lengths

#4 1/4, 3/8, 1/2, 5/8, 3/4

#6 1/4, 3/8, 1/2, 5/8, 3/4, 1, 1-1/4, 1-1/2

#7 1/2, 3/4, 1

#8 1/4, 3/8, 1/2, 5/8, 3/4, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#10 3/8, 1/2, 5/8, 3/4, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#12 1/2, 5/8, 3/4, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3

#14 1/2, 5/8, 3/4, 7/8, 1, 1-1/4, 1-1/2, 1-3/4, 2, 2-1/2, 3





Sizes - Steel/Plain

Sizes - Steel/Zinc

Hanger StudGimlet point for wood applications

Sizes

Toggle Bolt Round Head Slotted

Sizes

Lag Shield Insert

Diameter Lengths

8-32 1"

10-24 1-1/2", 2", 2-1/2", 3"

1/4-20 1-1/2", 2", 2-1/2", 3", 3-1/2"

5/16-18 2-1/2", 3"

3/8-16 2-1/2", 3", 3-1/2", 4"

Diameter Lengths

10-24 1-1/2", 2", 2-1/2", 3"

1/4-20 2", 2-1/2", 3", 3-1/2"

5/16-18 2-1/2", 3"

3/8-16 2-1/2", 3", 3-1/2"

Diameter Lengths

1/8-32 2,3,4

3/16-24 2, 3, 4, 5, 6

1/4-20 2, 3, 4, 5, 6

5/16-18 3, 4, 6

3/8-16 4, 6

Diameter Lengths

1/4 (S) 1, (L) 1/2

5/16 (S) 1-1/4, (L) 1-3/4

3/8 (S) 1-3/4, (L) 2-1/2

1/2 (S) 2, (L) 3

5/8 (S) 2, (L) 3-1/2

3/4 (S) 2, (L) 3-1/2

STUDS/TOGGLES/LAG SHIELDSSTUDS/TOGGLES/LAG SHIELDS




QUIK DRIVEAuto-Feed Screw SystemDelivers the superior holding power of screws and more speed than you ever dreamed possible.

QUIK DRIVE AUTO FEED SCREW SYSTEMQUIK DRIVE AUTO FEED SCREW SYSTEM




QUIK DRIVE FASTENERSQUIK DRIVE FASTENERS




Kalida-Kote™ In-House Painting Available For Custom Color Matching, Fast!

Aged CopperAlmond Ash GrayAztec GoldBanner RedBone WhiteBurnish SlateCape ClueCharcoal GrayCherokee BlueClassic GreenCocoa BrownColonial RedColony GreenCopper PennyCordovanCountry RedDark BronzeDesert SandEmerald GreenFern GreenHartford GreenHawaiian BlueLight StoneMansard Brown

Matte BlackMedium BronzeMusket GrayPacific BluePolar WhiteRed ClayRoman BronzeRoyal BlueRustic RedSageSahara Tan Sierra TanSeaportSlate BlueSlate GraySnow WhiteSnowdrift WhiteStone WhiteTeal GreenTerra Cotta Winter Blue

In-Stock Colors#42 - #43 - #44Call for Sizes

ButtonheadD

Rivet Dia.Drill No. & Hole Size

HHead

Dia. Nom.

EHead

Height Max.

LRivet Length

Max. Grip Range

Typical UltimateStrength (Lbs.)

(newtons)

Material Inch (mm) (mm) Inch (mm) Inch (mm) Inch (mm) Inch (mm) Shear Tensile

Plated-Steel RivetSteel MandrelOpen End

1/8" (.125)3.2

#30 (.129-.133)3.3 (3.28-3.38)

.2506.35

.0401.02

.212 (5.4)

.275 (7.0)

.337 (8.6)

.400 (10.2)

.462 (11.7)

.525 (13.4)

.650 (16.5)

.775 (19.7)

.032-.062 (0.8-1.6)

.063-.125 (1.7-3.2)

.126-.187 (3.3-4.8)

.188-.250 (4.9-6.4)

.251-.312 (6.5-7.9)

.313-.375 (8.0-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

2801240

4101820

3/16" (.187)4.8

#11 (.192-.196)4.9 (4.88-4.98)

.3759.53

.0559.53

.325 (8.3)

.450 (11.5)

.575 (14.6)

.700 (17.8)

.825 (21.0)

.950 (24.2)1.075 (27.3)1.200 (30.5)

.062-.125 (1.6-3.2)

.126-.250 (3.3-6.4)

.251-.375 (6.5-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

.626-.750 (16.0-19.1)

.751-.875 (19.1-22.2)

.876-1.000 (22.3-25.4)

6002665

8703870

5056Aluminum RivetSteel MandrelOpen End 1/8" (.125)

3.2#30 (.129-.133)3.3 (3.28-3.38)

.2506.35

.0401.02

.212 (5.4)

.275 (7.0)

.337 (8.6)

.400 (10.2)

.462 (11.7)

.525 (13.4)

.650 (16.5)

.775 (19.7)

.032-.062 (0.8-1.6)

.063-.125 (1.7-3.2)

.126-.187 (3.3-4.8)

.188-.250 (4.9-6.4)

.251-.312 (6.5-7.9)

.313-.375 (8.0-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

180800

2701200

3/16" (.187)4.8

#11 (.192-.196)4.9 (4.88-4.98)

.3759.53

.0551.40

.325 (8.3)

.450 (11.5)

.575 (14.6)

.700 (17.8)

.825 (21.0)

.950 (24.2)1.200 (30.5)

.062-.125 (1.6-3.2)

.126-.250 (3.3-6.4)

.251-.375 (6.5-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

.626-.750 (16.0-19.1)

.751-1.00 (19.1-25.4)

4401950

7003110

Aluminum RivetAluminum MandrelOpen End

1/8" (.125)3.2

#30 (.129-.133)3.3 (3.28-3.38)

.2506.35

.0401.02

.212 (5.4)

.275 (7.0)

.337 (8.6)

.400 (10.2)

.462 (11.7)

.525 (13.4)

.650 (16.5)

.775 (19.7)

.032-.062 (0.8-1.6)

.063-.125 (1.7-3.2)

.126-.187 (3.3-4.8)

.188-.250 (4.9-6.4)

.251-.312 (6.5-7.9)

.313-.375 (8.0-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

150660

180800

3/16" (.187)4.8

#11 (.192-.196)4.9 (4.88-4.98)

.3759.53

.0551.40

.325 (8.3)

.450 (11.5)

.575 (14.6)

.700 (17.8)

.825 (21.0)

.950 (24.2)1.075 (27.3)1.200 (30.5)1.450 (36.8)

.062-.125 (1.6-3.2)

.126-.250 (3.3-6.4)

.251-.375 (6.5-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

.626-.750 (16.0-19.1)

.751-.875 (19.1-22.2)

.751-1.00 (19.2-25.4)1.125-1.250 (28.6-31.8)

2801240

4301910

Stainless RivetSteel MandrelIFI Grade 50Open End

1/8" (.125)3.2

#30 (.129-.133)3.3 (3.28-3.38)

.2506.35

.0401.02

.212 (5.4)

.275 (7.0)

.337 (8.6)

.400 (10.2)

.462 (11.7)

.525 (13.4)

.650 (16.5)

.032-.062 (0.8-1.6)

.063-.125 (1.7-3.2)

.126-.187 (3.3-4.8)

.188-.250 (4.9-6.4)

.251-.312 (6.5-7.9)

.313-.375 (8.0-9.5)

.376-.500 (9.6-12.7)

5202310

6002660

3/16" (.187)4.8

#11 (.192-.196)4.9 (4.88-4.98)

.3759.53

.0551.40

.325 (8.3)

.450 (11.5)

.575 (14.6)

.700 (17.8)

.825 (21.0)

.950 (24.2)1.120 (30.5)

.062-.125 (1.6-3.2)

.126-.250 (3.3-6.4)

.251-.375 (6.5-9.5)

.376-.500 (9.6-12.7)

.501-.625 (12.8-15.9)

.626-.750 (16.0-19.1)

.751-1.000 (19.2-25.4)

11505110

13005780

#110 Copper RivetBrass MandrelIFI Grade 20Open End

1/8" (.125)3.2

#30 (.129-.133)3.3 (3.28-3.38)

.1256.35

.0401.02

.275 (7.0)

.400 (10.2).063-.125 (1.7-3.2).188-.250 (4.9-6.4)

215950

3001330

#5056 Aluminum Rivet Steel MandrelClosed End 1/8" (.125)

3.2

#30(.129-.133) .236 .035

.296 (7.52)

.355 (9.02)

.414 (10.52)

.473 (11.10)

.532 (13.51)

.591 (15.06)

.032-.062 (0.8-1.6)

.063-.125 (1.7-3.2)

.126-.187 (3.3-4.8)

.188-.250 (4.9-6.4)

.251-.312 (6.5-7.9)

.313-.375 (8.0-9.5)

2401060

2801240

GET-A -GRIP RIVETSGET-A -GRIP RIVETS




The Big Daddy is Marson’s most versatile and powerful hand riveter, taking the hard work out of setting large diameter blind rivets. Its extra-long handles provide excellent leverage and permit working afoot beyond natural reach. Other features include a patented bearing design, self-adjusting two-piece jaws and single-unit body construction with a steel insert to provide stronger threads for the nosepieces included. In addition, the Big Daddy features a double-gear reductionsystem which easily sets from 1⁄8" to 1⁄4" diameter Klik-Fast rivets in all alloys, including 1⁄4" Klik-Split® and 3⁄16" and 1⁄4" Klik-Lock® rivets. And a one-piece collet case eliminates the need to adjust the tool when changing rivet diameters. The Big Daddy comes with 5⁄32", 3⁄16" and 1⁄4" nosepieces which are stored in the body. Weight: 33⁄4 lbs.; 1/case.

Big Daddy Extended Nosepiece Kit/39009

Just two installed parts extend the reach of 39031 and /or39010 an additional 21⁄2". Weight: 1⁄4 lb.; 1/case.

HP-2®/39000

The HP-2 is the largest selling hand rivet tool in the industry. Known and trusted for durability, quality and performance, the HP-2 is often copied but never equaled. Its square shoulder fulcrum pin of cold-formed heat-treated steel prevents pin rotation that can elongate the engaging holes and cause premature tool failure in imitation tools. Other quality features include: precision die-case, high-strength aluminum alloy body; drop-forged carbon steel upper handle; and thick, cushion-molded vinyl grips for comfort. The HP-2 sets up to3⁄16" steel rivets and comes with four mounted nosepieces (3⁄32", 1⁄8", 5⁄32" and 3⁄16") and a service wrench. Refer to the Riveter Capacity Chart on page 24 for specific capabilities.Weight: 1.2lbs.; 1/carton.

This is the same tool as 39031, but comes with 3⁄16", 1⁄4" and special 1⁄4"Klik-Split® rivet nosepieces. Weight: 33⁄4 lbs.; 1/case.

This is the same tool as 39010, but comes with 39009 attached, extending thetool’s reach by an additional 21⁄2". Weight: 4 lbs.; 1/case.

Extended head

Big Daddy/39010

Big Daddy/39035

Big Daddy®/39031

Rivet Sizes Monobolt® Sizes T-Rivet Sizes

Tool 3/32" 1/8" 5/32" 3/16" 1/4" 3/16" 1/4" 3/16" 1/4"

39000 39131 39128 39130 39129 -- -- -- -- --

39040 39131 39128 39130 39129 -- -- -- -- --

39031 -- 96024 96025 96026 96027 96031 96030 96029 96028

* When setting Marson Klik-Lock® rivets, no special nosepiece is required.

Nose Piece Chart

RIVETSRIVETS

MARSON®




Fab-Lok® FastenersMaintains panel integrity in high-stress environmentsVibration, either from inside or outside a building, can make ordinary fasteners loosen and back out. Fab-Lok® fasteners combine a slotted aluminum sleeve and fastener to provide the simplicity and strength of both elements.

Features• Hex washer head machine screw assembled to a slotted aluminum sleeve and EPDM sealing washer.• Carbon steel or stainless steel screws.• Installs with power drive equipped with Fab-Lok® holding sleeve.

Benefits• After tightening, clamping tines remain in place even if the screw is removed• Greater joint integrity• Consistent drill times and hole sizes• Increased construction efficiency

Weath-R-Seal® Washers Fab-Lok® Fasteners

Single Shear Strength Hydrostatic Test

Type FAC - Single Sheet Thickness Comparison - FAB-LOK® & Sheet Metal Screw

Type FAC - Double Sheet Thickness

Clamping Force

* FAB-LOK®, even when stripped, retains a residual clamp-up and remains effective. Sheet metal screws are loose when stripped.

Fatigue testsTwo thicknesses of 26 gage metal fastened with FAB-LOK® and tested on 5000 lb. capacity machine at 1500 cycles per minute, sustained 1,776,500 cycles when failure of sheets occurred. Fastener did not fail.

FAB-LOK® fastening 1/8" aluminum plate to 3/16" steel of a railroad freight car, held without failure when the car was subjected to jarring vibration bya Hewitt-Robins Car Shaker at 900 cycles per minute for ten minutes.

FAB-LOK® Performance FeaturesPull-out tests were performed on a Model L Dillon Dynamometer. FAB-LOK® fasteners were installed in single sheet and two sheets of metal and pulled over the tines of the FAB-LOK® to determine holding values.

Information provided herein is based upon tests believed to be reliable. In as much as Fabco Fastening Systems has no control over the exact manner in which others may use this information, it does not guarantee the results to be obtained. Nor does the Company make any express or implied warranty of merchantability, or fitness for a particular purpose concerning the effects or results of such use.

After Installation

FAB-LOKFAB-LOK® ® RIVETSRIVETS

Part Description

Aluminum Bonded .729" O.D. – .040 Aluminum

Weath-R-Seal® Washers 1" O.D. – .040" Aluminum

304 Stainless Steel Bonded .729" O.D. 20 gage 304 S/S

Weath-R-Seal® Washers 1" O.D. 20 gage 304 S/S

Material SizePenetrating

Len gth Grip Range Wt./MCarbon Steel FAS 10-4 1.373" .062"-.250" 23

FAS 10-8 1.612" .250"-.500" 24FAS 10-12 1.807" .500"-.750" 28

H-3 (300 Series) FAC 10-4 1.373" .062"-.250" 23Stainless Steel FAC 10-8 1.612" .250"-.500" 24

FAC 10-12 1.807" .500"-.750" 28

Fab-Lok Type FASMaximum 900 lbs.Residual 860 lbs.

Fab-Lok Type FAC FASAverage Shear 1885 lbs. 2400 lbs.

Fab-Lok Type H20 Pressure Length of test ResultFAC-10-4 100 psi 5 days No Leaks

Sheet Material

Sheet Thickness

* Failure lbs.

Type of Failure

Steel

24 ga.20 ga.18 ga.16 ga.14 ga.

833858105012931400

Sheet SplitSheet SplitSheet SplitSheet Split

Fastener Broke

Sheet Material

FAB-LOKFAS-10-4

#14 SheetMetal Screw

Strip test in .032" Aluminum 75 inch-lbs.* 65inch-lbs.*Strip test in 26 ga. Steel 75 inch-lbs.* 65inch-lbs.*Strip test in 24 ga. Steel 75 inch-lbs.* 65inch-lbs.*

Sheet Material

Sheet Thickness

* Failure lbs.

Type of Failure

Steel 26 ga.20 ga.

11601345

Sheet SplitSheet Bent

Fastener TinesBroke

Aluminum .032" 915 Sheet Split




Grommet SealGrommet Seal Fasteners are compression fasteners used in Side-lap applications which utilize fiberglass, plastic or composite sheeting.

Grommet Seals consist of:

• A Hex Head machine screw• A bonded sealing washer• An elongated rubber sleeve with an internal molded brass nut.

After Installation

Grommet Size: 1/4" X 1" 3/8" X 1"* 3/8" X 1-1/4"*Body Length: .948 .812 1.000

Nut Insert: 6-32 10-32 10-32

Durometer (sleeve): 70 60 60

Ultimate Tensile: 50 Lbs. 80 Lbs. 80 Lbs.

* Also Available in 316 Stainless Steel.

Machine Screw Size: 6-32" X 1" 10-32 X 1"* 10-32 X 1-1/4"*Hex Size: 1/4" 5/16" 5/16" Material: 302 HQ 302 HQ 302 HQ Bonded Washer: 304 SS/EPDM 304 SS/EPDM 304 SS/EPDMSleeve: EPDM EPDM EPDMNut Insert: Brass Brass BrassRecommendedHole Size: .250 .375 .375Grip Range: .375-.607 .312-.450 .312-.545

InstallationThe grommet is installed by placing it into a pre-drilled 1/4" or 3/8" hole and tightened using a screw gun with a standard 1/4" or 5/16" socket. The machine screw engages the nut insert, forcing the sleeve to expand against the inner wall of the materials. Grommets become an excellent sealant against air, moisture and vibration.

BULB-TITE RIVETSBULB-TITE RIVETS

Specifications

BULB-TITE RivetsMore than forty years ago the first Bulb-tite was developed to solve application requirements in the Pre-Engineered Metal Building industry. Since that time the Bulb-Tite product line has been expanded to meet application requirements in a wide range of industries. The Bulb-tite rivet body folds into three separate legs forming a large blind-side head. This large bearing head evenly distributes the Bulb-tite's high clamp force in soft, thin or brittle materials while providing high pull through resistance.

The Bulb-tite's wide grip range enables a single Bulb-tite to work in a greater variation of thickness. Some versions of the Bulb-tite feature a special flush break mandrel that effectively seals the rivet bore and adds greater shear strength.

GROMMET SEAL RIVETSGROMMET SEAL RIVETS

SizesMaterial: 5056 AluminumWasher: NeopreneBody Diameter: .304"Drill Size: 5/16"

Grip Range P.N. .042" - .375" BT31375.250" - .625" BT31625




Copper and 304 Stainless Steel Roofing Nails• 1lb. - 5 lb. - bulk Boxes

Framing-Sinkers• 1lb. - 5 lb. - bulk coated

Length2", 2-1/2", 3-1/4", 3-1/2"

EG Roofing Nails• 1lb. - 5 lb. - bulk coated

Length 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3"

Drywall Nails• 1lb. - 5 lb. - bulk boxes, cupped head

Length 1-3/8", 1-5/8"

Finish Nails• 1lb. - 5 lb. - bulk brite finish

Length1-1/2", 2", 2-1/2"

Gauge Lengths 12 3/4",1", 1-1/4", 1-1/2", 2" 11 3/4",1", 1-1/4", 1-1/2", 2" 10 1", 1-1/4", 1-1/2", 2", 3"

Concrete Nails• Fluted shank for fast penetration into “uncured" concrete.• 3/4" penetration into the concrete is recommended• Hot Dipped Galvanized

Length3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 3", 3-1/4", 4", 4-1/2", 5, 5-1/2", 6", 7", 8"

Length 1-1/8"

Tension Nails• 1lb. - 5 lb. - bulk boxes

Leg Length3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3"

Plastic Cap Nails• Bulk Boxes• Fastening roof felt to decks

ButtonKap PlusButtonKap Nailer and Roofing Nailer

• Can be used as a ButtonKap Nailer and a Roofing Nailer• Saves Labor and Time• Shoots Steel and Plastic Caps• 3/4" and 1 3/4"• Fast, Easy Loading• Uses Coil Roofing Nails

NAILSNAILS




Length 2", 2-3/8", 3", 3-1/4", 3-1/2"

Framing

Length2", 2-3/8", 3", 3-1/4", 3-1/2"

Diameters.113", .120", .131"

Smooth or Ring Shank Diameters.099", .120", .131"

Diameter.120"

RoofingLength7/8", 1", 1-1/4", 1-1/2", 1-3/4"

Finish

Length3/4", 1", 1-1/4", 1-1/2", 2"

Wide Crown (15/16")Length5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2"

18 gaugeSenco, Paslode, Porter Cable, Hitachi, and Bostitch are registered trademarks.

16 gauge

16 gauge

Framing (strip)

Coil Nails

Available for Bostitch - Senco - Paslode - Hitachi - Porter Cable

Strip Nails

Strip Crown StaplesAvailable Finish: Brite - Electro Galvanized - Hot Dip

Medium Crown (1/2")Length 3/4", 1", 1-1/4", 1-3/8", 1-1/2", 1-3/4", 2"

Narrow Crown (3/16")Length1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4"

COLLATED PNEUMATIC NAILSCOLLATED PNEUMATIC NAILS




SNS41Compact and lightweight, a great performer in most 16 gage staple jobs.

• Oil-less design; no need to lubricate.• Fast multi-directional stitching.

7⁄16" crown. 16 gauge staples. 1" - 2" lengths. Capacity 160+.*2" staples for soft wood applications only.

SLS20XPPowerful finish and trim staplers designed for easy handling and virtually trouble-free maintenance.

• Lightweight and easy to handle with ergonomic design and soft grip.

• Adjustable depth-of-drive control allows for precise countersinking.

• Designed with only one movable seal for virtually trouble-free operation.

Available crown widths 3⁄16", 1⁄4", 3⁄8" . 18 gauge staples. 3⁄8" - 1 1⁄2" lengths. Capacity 168.

Leg Length5/16", 3/8", 1/2", 9/16"

• Arrow brand high quality• Fits Arrow, Stanley, Craftsman, B&D Hand Staplers

• Easy Squeeze Mechanism• 2 Year Limited Home Use Warranty• All Purpose• Heavy Duty• Shoot a Staple Wherever You Would Drive a Nail

Model T37

ARROW Staple Gun Tacker

SENCO® STAPLERSSENCO® STAPLERS

TRIANGLE FASTENER CORPORATION800.486.1832 / www.trianglefastener.com



53

FASTENERSFOR

LOW SLOPE ROOFING

TFC offers the largest selection of fasteners for the low slope roofing industry!

Need it now?Ask us to about our NEED-IT-NOW! trade specific product program for low slope roofing.

Contact our product specialists who are trained to support you with a wide variety of standard and specialty fasteners for your application.

We also specialize in fastening solutions for those difficult connections and all of our fasteners are designed for the professional construction trades assuring high performance and long-life.

�Fastening recommendations �Job site support �Product testing �Pricing Programs

TRIANGLE FASTENER CORPORATIONTRIANGLE FASTENER CORPORATION800.486.1832 / www.trianglefastener.com800.486.1832 / www.trianglefastener.com



54

We also offer fasteners compatible with the following roof systems

Carlisle • Firestone • GAF Genflex • Johns-Manville

Sarnafil • Soprema • Tamko • Versico

THE MOST COMPREHENSIVE FASTENER LINES ANDSUPPORT PROGRAMS IN THE ROOFING INDUSTRY!

SENTRYROOFING SCREWSPLUS FIVE

R

#10-11 GIMLET POINTBUTTON HEAD Uses: 20 ga. or thinner steel deck and wood deck.Material: Carbon Steel

Corrosion Protection: Epoxy coating (black) meets or exceeds FM4470 corrosion standards and withstands 25 cycles of the Kesternich DIN 50018 SFW 2.0 test.

ATTACHMENT TIPS

Metal Deck: Fastener must penetrate the deck by a minimum of 3/4".

Concrete and Wood: Fastener embedment of at least 1" or a minimum of 1" penetration through wood decking.

Sentry Plus Five fasteners are FM approved and fastener coatings meet FM specification #4470. Contact your TFC product professional for approval details.

Product and Installation Support• Fastener recommendations• Job-site assistance• Product training• Delivery programs• Technical assistance

Need it now?Ask about our NEED-IT-NOW! product program that helps you fi nd those hard to fi nd fasteners for diffi cult applications.

Screw Length Thread Length Pieces/Box Weight/Box

1-5/8" (41mm) FULL 1000 12# (5kg) 2-1/4" (57mm) FULL 1000 14# (6kg) 2-7/8" (73mm) FULL 1000 18# (8kg) 3-3/4" (95mm) 2-7/8" (73mm) 1000 23# (10kg) 4-1/2" (114mm) 4" (102mm) 1000 26# (12kg)

5" (127mm) 4" (102mm) 1000 29# (13kg) 6" (152mm) 4" (102mm) 1000 34# (15kg)

Pull-out Values in Wood

1/2" Plywood 348 lbs.(156kg)

3/4" Plywood 585 lbs.(263kg)

Wood Plank - 1"

Embedment

353 lbs.(159kg)

Pull-out Values in Steel

20 Ga. 560 lbs.(252kg)

22 Ga. 410 lbs.(184kg)

24 Ga. 364 lbs.(163kg)


We will go to the job and perform pullout

tests to assist you in determining the

proper fastener.




55

#12-15 DP1 DRILL POINT TRUSS HEADUses: Wood or steel (16 ga. - 22 ga.). Material: Carbon Steel

Back-out Resistance: Typical back-out steel deck (18 ga. through 24 ga.) 10 - 14 in lbs.


Head Height: .095" - .105"Head Diameter: .425" - .440"

Sentry Plus Five fasteners are FM approved and fastener coatings meet FM specification #4470. Contact your TFC product professional for approval details.


R

#12-15 DP1 DRILL POINT 1/4" HEX WASHER HEADUses: Wood or steel (16 ga. - 22 ga.). Material: Carbon Steel

Back-out Resistance: Typical back-out steel deck (18 ga. through 24 ga.) 10 - 14 in lbs.


THE LARGEST THE LARGEST SELECTION OF ROOFING OF ROOFING SCREWS IN THE INDUSTRY!SCREWS IN THE INDUSTRY!

Screw Length Thread Length Pieces/Box Weight/Box

1-5/8" (41mm) FULL 1000 12#2-1/4" (57mm) FULL 1000 16#2-7/8" (73mm) FULL 1000 19#3-1/4" (83mm) 2-7/8" (22mm) 1000 22#3-3/4" (95mm) 2-7/8" (22mm) 1000 25#4-1/2" (114mm) 4" (101mm) 1000 30#

5" (127mm) 4" (101mm) 1000 32#6" (152mm) 4" (101mm) 1000 38#7" (177mm) 4" (101mm) 1000 42#8" (203mm) 4" (101mm) 1000 48#

Pull-out Values in Steel18 Ga. 558 lbs.20 Ga. 456 lbs.22 Ga. 452 lbs.24 Ga. 335 lbs.

ATTACHMENT TIPS

Metal Deck: Fastener must penetrate the deck by a minimum of 3/4".

Concrete and Wood: Fastener embedment of at least 1" or a minimum of 1" penetration through wood decking.





56

ATTACHMENT TIPSMetal Deck: Fastener must penetrate the deck by a minimum of 3/4".

Concrete and Wood: Fastener embedment of 1" or a minimum of 1" penetration through wood decking.

#14-13 DP1 DRILL POINTTRUSS HEADCARBON STEELUses: Wood, concrete or steel (16 ga. - 22 ga.).Material: Carbon Steel



#14-13 DP1 DRILL POINT TRUSS HEADSTAINLESS STEELUses: Wood or steel (16 ga. - 22 ga.).Material: TRIM-RIITE martensitic stainless steelpassivated. Magnetic

Factory Mutual Systems Approved: JI-1H2Ao.AM, JI-0J9A1.AM, JI-1G1A6.AM. 18 ga.- 20 ga. - 22 ga. metal decks, wood decks and reroof steel decks.

Corrosion Protection: Passivated meets or exceeds FM4470 corrosion standards and withstands 30 cycles of the Kesternich DIN 50018 SFW 2.0 test.


THE LARGEST SELECTION OF ROOFING THE LARGEST SELECTION OF ROOFING SCREWS IN THE INDUSTRY!SCREWS IN THE INDUSTRY!

Screw Length Thread Length Pieces/Box Weight/Box1-1/2" FULL 1000 14#

2" FULL 1000 18#3" FULL 1000 26#4" 3-7/8" 1000 31#5" 3-7/8" 1000 42#6" 3-7/8" 1000 47#7" 3-7/8" 500 27#8" 3-7/8" 500 30#9" 3-7/8" 500 34#

10" 3-7/8" 500 38#11" 3-7/8" 500 43#12" 3-7/8" 500 45#


Pull-out Values in Concrete3000PSI

1” Embedment 740 lbs.

Pull-out Values in Wood1/2" Plywood 442 lbs.3/4" Plywood 495 lbs.Wood Plank

1" Embedment 517 lbs.

Shear Strength in Concrete3000PSI


(Loads are average ultimate)

Properties Annealed Annealed Hardened*02% Yield Strength

KSi 57 184MPa 394 1270

Tensile StrengthKSi 94 260MPa 650 1800

% Elongation (in 1") 35 14% Reduction of Area 68 52Hardness B87 C50*1900°F 15 minute aircool plus 400°F hr, AC

Screw Length Thread Length Pieces/Box Weight/Box1-1/2" FULL 1000 14#

2" FULL 1000 18#3" FULL 1000 26#4" 3-7/8" 1000 31#5" 3-7/8" 1000 42#6" 3-7/8" 1000 47#7" 3-7/8" 500 27#8" 3-7/8" 500 30#9" 3-7/8" 500 34#

10" 3-7/8" 500 38#11" 3-7/8" 500 43#12" 3-7/8" 500 45#




Pull-out Values in Wood1/2" Plywood 442 lbs.3/4" Plywood 495 lbs.Wood Plank


Shear Strength in Concrete3000PSI






R




57

#15-13 DP1 DRILL POINT TRUSS HEADCARBON STEELUses: Wood, concrete or steel (16 ga. - 22 ga.).Material: Carbon Steel



3" METAL STRESS PLATETesting: Meets or exceeds Factory Mutual I-60 or I-90 wind up liftspecifi cations when properly installed on most insulation boards.Feature: Plate is formed from 26 gauge GalvalumeTM steel.Use with Phillips Truss Head fastener.Uses: They are used with virtually all types of insulation board usedfor roofi ng systems.Galvalume is a trademark of BIEC International, Inc.

Square, Hex, Round...Steel or Plastic...We have what you need!3" x 3" Square Recessed Galvalume Metal3" x 3" Square Flat Bottom Galvalume Metal3" Across Flats Hex Galvalume Metal3" Across Flats Hex Plastic2" Round Galvalume Metal (Standard)2" Round Galvalume Metal (Recessed)2" Round Galvalume Metal with Plastic Locking Feature2" Round Galvalume Metal with Plastic Locking Feature and Protective Outer Ring3" Round Galvalume Metal (Standard)3" Round Galvalume Metal (Recessed)3" Round Plastic 3" Round Plastic with Locking Feature


Screw Length Thread Length Pieces/Pail Weight/Pail1 1/4 FULL 1000 14#

2 FULL 1000 21#3 2 7/8 1000 31#4 3 7/8 1000 40#5 3 7/8 1000 49#6 3 7/8 500 29#7 3 7/8 500 34#8 3 7/8 500 38#9 3 7/8 500 43#

10 3 7/8 500 48#11 3 7/8 500 52#12 3 7/8 500 57#14 3 7/8 250/Bx 33#/Bx16 3 7/8 250/Bx 38#/Bx18 3 7/8 250/Bx 43#/Bx20 3 7/8 250/Bx 47#/Bx22 3 7/8 250/Bx 52#/Bx24 3 7/8 250/Bx 56#/Bx

Pull-out Values in Steel18 Ga. 916 lbs.20 Ga. 916 lbs.22 Ga. 538 lbs.




Pull-out Values in Wood19/32” Plywood 485 lbs.1” Wood Plank

Full penetration1/2” embedment

995 lbs. 543 lbs.


ATTACHMENT TIPSMetal Deck: Fastener must penetrate the deck by a minimum of 3/4".

Concrete and Wood: Fastener embedment of 1" or a minimum of 1" penetration through wood decking.

Great for retrofi t base attachment. Tap up to 1/2" thick steel. Use 1/4" drill bit.


R




58



R




59

TB-50 Termination Bar with Sealant Ledge

Material: Specially extruded aluminum without sharp edges.Dimensions: .050 thick x 1" wide x 10’ long per piece.Holes: 1/4" x 3/8" slotted holes on 6", 8" or 12" centers.Packaged: 50 pieces per tube.Approx. Shipping Weight: 45 pounds per tube.


Material: Specially extruded aluminum without sharp edges.Dimensions: .075 thick x 1" wide x 10’ long per piece.Holes: 1/4" x 3/8" slotted holes on 6", 8" or 12" centers.Packaged: 50 pieces per tube.Approx. Shipping Weight: 51 pounds per tube.


Material: Extruded aluminum without sharp edges.Dimensions: .085 thick x 1" wide x 10’ long per piece.Holes: 1/4" x 3/8" slotted holes on 6", 8" or 12" centers.Packaged: 25 pieces per tube.Approx. Shipping Weight: 43 pounds per tube.


Material: Specially extruded aluminum without sharp edges.Dimensions: .100" thick x 1" wide x 10’ long per piece.Holes: 1/4" x 3/8" slotted holes on 6", 8" or 12" centers.Packaged: 50 pieces per tube.Approx. Shipping Weight: 68 pounds per tube.


Material: Specially extruded aluminum without sharp edges.Dimensions: .125" thick x 1" wide x 10’ long per piece.Holes: 1/4" x 3/8" slotted holes on 6", 8" or 12" centers.Packaged: 50 pieces per tube.Approx. Shipping Weight: 78 pounds per tube.

RD-100 Retaining Drain Bar

Material: Specially extruded aluminum without sharp edges.Dimensions: .100" thick x 1" wide x 10’ long per piece.Mounting Holes: 1/4" x 3/8" slotted holes on 6" centers.Packaged: 10 pieces per tube.Drainage Slots: 3/8" x 1 1/2" slotted drain holes on 4" centersApprox. Shipping Weight: 78 pounds per tube.

LIMITED WARRANTYTru-Fast hereby gives, to the original purchaser only, a warranty for defects in manufacture or workmanship on its products for ten (10) years from date of purchase. This warranty is in lieu of all other warranties, express, implied or statutory. This warranty is also in lieu of any other obligations and liabilities on the part of Tru-Fast. Tru-Fast’s sole obligation under this warranty shall be replacement of the Tru-Fast product which is deemed to be defective. Tru-Fast neither assumes nor authorizes any person to assume for it or any other obligation or liability whatsoever in connection with its products. In no event shall Tru-Fast be liable for special, consequential or incidental damages for breach of said warranty, nor for the improper selection of Tru-Fast Products a particular application.

For use with Ballasted or Non-Ballasted Systems

TERMINATION BARTERMINATION BARSENTRYROOFING SCREWSPLUS FIVE

R




STRUCTURAL INSULATED PANELSTRUCTURAL INSULATED PANEL(SIP) AND NAIL BASE FASTENERS(SIP) AND NAIL BASE FASTENERS

Need more pullout, back-out, and corrosion resistance?Take a look at our #14 CONCEALOR DP1 pancake head screws on page 21. They are FM approved for nail base attachment and are designed with a buttress thread form for superior performance.

We offer the widest selection of fasteners for attachingstructural insulated panels and nail base to metal or wood.

61




STRUCTURAL INSULATED PANELSTRUCTURAL INSULATED PANEL(SIP) AND NAIL BASE FASTENERS(SIP) AND NAIL BASE FASTENERS

We offer the widest selection of fasteners for attachingstructural insulated panels and nail base to metal or wood.

Need more pullout, back-out, and corrosion resistance?Take a look at our #14 CONCEALOR DP1 pancake head screws on page 21. They are FM approved for nail base attachment and are designed with a buttress thread form for superior performance.




62

FM-75 BASE SHEET FASTENERSFM-75 BASE SHEET FASTENERSSENTRYROOFING SCREWSPLUS FIVE

R




63


R




64


R




65


R




66


R




67


R




68

TWIN LOC-NAIL BASE SHEET FASTENERSTWIN LOC-NAIL BASE SHEET FASTENERSSENTRYROOFING SCREWSPLUS FIVE

R




69

TWIN LOC-NAIL BASE SHEET FASTENERSTWIN LOC-NAIL BASE SHEET FASTENERSSENTRYROOFING SCREWSPLUS FIVE

R




Regular Round Head

Fastening Required Required Shank Range Deck Shank Gage Max. Total Penetration Deck Pieces/ # Length Thickness Plywood Wood Penetration Pounds 1 1/2" 12 1/16" The 1/2" 109 2 5/8" 12 1/16" nail 5/8" 106 3 3/4" 12 1/16" must 3/4" 102 4 7/8" 12 1/16" pass 7/8" 99 5 1" 12 1/16" through 1" 96 6 1 1/4" 12 1/4" the 1" 91 7 1 1/2" 11 1/2" plywood 1" 78 8 1 3/4" 11 3/4" by a 1" 73 9 2" 11 1" 1/4" 1" 69 10 2 1/2" 11 1 1/2" 1" 62 11 3" 11 2" 1" 56

Ring or Smooth Shank

Sizes and Quantities

Shank Types Coating Types Container Types Cap Diameter Nail Materials Annular Grooved Bright 25 Lbs. Boxes 1" Hi-Carbon Steel Smooth Yellow Di-chromate 50 Lbs. Boxes Electro Galvanized Hot Dipped Galvanized Pails Rust-Lok®

Design Options

Pieces Nail Shank Head Per Length Size Diameter Pound 3" 9 ga. 1" 44 3 1/2" 9 ga. 1" 39 4" 9 ga. 1" 36 5" 9 ga. 1" 31 6" 8 ga. 1" 27 7" 8 ga. 1" 24 8" 8 ga. 1" 20


Uses: BUR applications and other applications where thick insulation's are attached to wood substrates. Available in ring shank or smooth shank.

Masonry Round Head 3/4" 9 ga. 1" 84 1" 9 ga. 1" 76 1 1/4" 9 ga. 1" 64 1 3/4" 9 ga. 1" 70 1 1/2" 9ga. 1" 59 2"- 6" 9 ga. 1"

Fluted Shank

Insulation Round HeadRing or Smooth Shank

Plex-Cap®Plastic Cap NailsRing Shank

3/4" 12 1/2 ga. 1" 352 7/8" 12 1/2 ga. 1" 318 1" 12 1/2 ga. 1" 298 1 1/4" 12 1/2 ga. 1" 274 1 1/2" 12 1/2 ga. 1" 170 1 3/4" 12 1/2 ga. 1" 149 2" 12 ga. 1" 132 2 1/2" 12 ga. 1" 110 3" 12 ga. 1" 94

Uses: For fastening applications of roofing felt, insulation, hose wraps, & polyfilm. Manufactured from high strength polymer plastic.

Square Cap Nail 3/4" 12 ga. 1" 63 7/8" 12 ga. 1" 62 1" 12 ga. 1" 61 1 1/4" 12 ga. 1" 58 1 1/2" 12 ga. 1" 56 1 3/4" 12 ga. 1" 54

SIMPLEX

ROOFING - CAP NAILS ROOFING - CAP NAILS

71




Tube-Lok® Fasteners

Fastening Range Required Shank Shank Max. Total Deck Pieces / Pieces / Pounds / # Length Gage Thickness Penetration Pounds Box Box 1 1" 0.108 0" 1" 78 2,500 40 2 1 3/4" 0.108 1/4" 1.5" 66 2,500 52 3 2 1/2" 0.108 1" 1.5" 56 2,500 62 4 3" 0.108 1 1/2" 1.5" 51 2,500 63 5 3 1/2" 0.108 2" 1.5" 46 2,500 70 6 4 1/2" 0.108 3" 1.5" 39 1,000 36 7 5 1/2" 0.108 4" 1.5" 34 1,000 40 8 6 1/2" 0.108 5" 1.5" 30 1,000 45

Patented


* Approximate count.

Assembled Tube-Lok® New Item

Pieces Nail Tube Head Per Length Diameter Diameter Pound 1 3 /4" .197" 2" 25


Uses: Effective attachment of roofing products to low and steep slope decks fabricated from Gypsum, cellular and aggregate lightweight concrete, cementitious wood fiber and other lightweight deck assemblies. Assembled for faster installation. New Simplex Installation Tool.

Base-Lok®Patented

Nail Length: 1 3/4" Carton contains 1000 pieces.


Uses: The Simplex Base-Lok® is used to secure base sheet to aggregate lightweight concrete, cellular lightweight concrete decks. Easy to install one piece fastener manufactured from engineered plastic.

Shank Types Coating Types Container Types Cap Diameter Nail Materials Annular Grooved Bright 25 Lbs. Boxes 1" Hi-Carbon Steel Smooth Yellow Dichromate 50 Lbs. Boxes Electro Galvanized Hot Dipped Galvanized Pails Rust-Lok®

Design Options

Simplex #2 Simplex #3 Standard Building Codes Rupture Rupture Term Rust-Lok® and Standard Simplex # Substrate Roofing Material Fastener Plate Plate Bars Coating Approvals Brand Tools 1 Wood Deck 15 lbs. & 30 lbs. Felt Plastic Cap Nails None Pole-Tap® or Hand Tap®

“Original" Metal 1" Cap Nails APA & FFN-105B Pole-Tap® or Hand Tap®


Base Sheet “Original" Metal 1" Cap Nails APA & FFN-105B Pole-Tap® or Hand Tap®


Insulation Insulation Metal Cap Nails APA & FFN-105B Pole-Tap® or Hand Tap®

Recover Board over Old Roof Insulation Metal Cap Nails APA & FFN-105B Pole-Tap® or Hand Tap®

2 Gypsum Deck Base Sheet “Original" Tube-Lok® 1" Cap Nails Dade Pole-Tap® or Hand Tap® “Assembled" Tube-Lok® 2" Nails Pending Tube-Tap®

Base-Lok® Fasteners Dade & FM Drill-Tap®, Extend Zip® or Base-Zip®

Insulation “Original" Tube-Lok® 1" Cap Nails Dade Pole-Tap® or Hand Tap®

Recover Board over Old Roof “Original" Tube-Lok® 1" Cap Nails Dade Pole-Tap® or Hand Tap®

3 Light Weight Base Sheet “Original" Tube-Lok® 1" Cap Nails Dade Pole-Tap® or Hand Tap®

Concrete “Assembled" Tube-Lok® 2" Nails Pending Tube-Tap® Deck Base-Lok® Fasteners Dade & FM Drill-Tap®, Extend Zip® or Base-Zip®



4 Tectum Deck Base Sheet “Original" Tube-Lok® 1" Cap Nails Dade Pole-Tap® or Hand Tap® “Assembled" Tube-Lok® 2" Nails Dade Pole-Tap® or Hand Tap® Base-Lok® Fasteners Dade & FM Drill-Tap®, Extend Zip® or Base-Zip®



5 Masonry Wall Base Flashing Masonry Cap Nails None None Zanchor® Zinc Hammer Drive Nails None None

6 Wood Wall Base Flashing “Original" Metal 1" Cap Nails APA & FFN-105B Hand Tap® “Original" Metal 2" Cap Nails APA & FFN-105B Hand Tap®

7 Gypsum Wallboard Base Flashing Wall-Lok® Zinc Drywall Anchors None None

The Simplex Roofing Fastener Selection Table

SIMPLEX

ROOFING - CAP NAILS ROOFING - CAP NAILS




72

Plates & AccessoriesUse 3" steel plate, 2" steel plate (with barbs), or batten bar.

Use a carbide tip drill bit for gypsum, lightweight concrete and some cementitious wood fiber applications.

PHYSICAL DATA CAT. NO. LENGTH PACKAGING WEIGHTThe data below is constant for NTB1025WO 2 1/2" 500 13 lb.each Olympic NTB-1HWO NTB1030WO 3" 500 15 lb. NTB1035WO 3 1/2" 500 17 lb.Head Size:1" Diameter NTB1040WO 4" 500 19 lb. NTB1045WO 4 1/2" 500 21 lb.Head Style:Double Internal NTB1050WO 5" 500 24 lb.Hex Drive NTB1055WO 5 1/2" 500 26 lb. NTB1060WO 6" 500 28 lb.Major NTB1065WO 6 1/2" 500 29 lb.Thread NTB1070WO 7" 500 30 lb.Diameter: .750 NTB1075WO 7 1/2" 500 32 lb. NTB1080WO 8" 250 16 lb.Thread: 3.5 T.P.I. Buttress NTB1085WO 8 1/2" 250 17 lb. NTB1090WO 9" 250 18 lb.Material: Glass-Filled Nylon NTB1095WO 9 1/2" 250 19 lb. NTB1100WO 10" 250 20 lb.

Polymer Gyptec AugersFast FactsA glass-filled nylon auger fastener with a 1" head designed to secure insulation and single-ply membrane to gypsum, all cementitious wood fiber, Tectum® and certain lightweight concrete decks.

Features & Benefits• Thread design & large root diameter: • Increase pullout resistance • Increase side shear strength

• Made from glass-filled nylon which: • Eliminates corrosion • Eliminates thermal bridging and condensation • Yields high tensile strength

• F.M. and MIAMI-Dade approved.

Plates & AccessoriesThere are various 2" and 3" plate combinations.Use a high speed steel or centering drill bit.

NC FASTENERSFast FactsDesigned for attaching insulation and single-ply membrane to fiberglass reinforced plastics, light gauge metal and decks in highly humid or corrosive atmospheres.

Features & Benefits• Made of a specially formulated nylon which:• Eliminates thermal bridging.• Eliminates fastener corrosion.

• Pre-assembled nut & bolt design offers:• High pullout values in fiberglass reinforced decks and marginal metal decks.• Increased back-out resistance.

• The 2" built-in stress plate:• Reduces installation time.• Prevents fastener pop-up.

• F.M. and Dade County approved.

Physical Data Cat. No. Length Packaging WeightThe data below is NC1 04 4" 500 14 lbconstant for each NC1O6 6" 500 17 lbNC Fastener. NC1O8 8" 500 191b NC11O 10" 500 231bHead Diameter: 1 "or 2" NC112 12" 500 271bHead Height: .100 or .260 2" BUILT-IN STRESS PLATEHead Style: NC204 4" 500 23 lbDouble Internal NC206 6" 500 26 lbHex Head NC208 8" 500 29 lbMaterial: Nylon NC21O 10" 250 15 lbBody Diameter: 290 NC212 12" 250 181b

Combined Thickness Of Membrane and/or Existing Substrate

NC Fastener Minimum Total Maximum Total Length Thickness Thickness 4" 1 1/4" 3 3/4" 6" 2 1/2" 5 3/4" 8" 4 1/2" 7 3/4" 10" 6 1/2" 9 3/4" 12" 8 1/2" 11 3/4"

NC FASTENER LENGTH SELECTION PROCEDURE

FASTENERS FOR LIGHTWEIGHT DECKSFASTENERS FOR LIGHTWEIGHT DECKSSENTRYROOFING SCREWSPLUS FIVE

R




73

FASTENERS FOR LIGHTWEIGHT DECKSFASTENERS FOR LIGHTWEIGHT DECKSSENTRYROOFING SCREWSPLUS FIVE

R




DOW

Insta-Stik professional roof adhesive is a single componentpolyurethane adhesive dispensed from a portable, disposablepre-pressurized container requiring no external power source.

Insta-Stik is used to attached compatible roof insulationboards to roof decks and substrates in new construction androof replacement applications. This includes insulation boardto insulation board, insulation board to Class 1 non-graveled(bald) build-up roofs for re-cover applications and insulationor gypsum board to 22 gauge and thicker steel decks andwood decks.

Wood Deck:Insta-Stik works on wood decks whenever metal fasteners arenot desired. The insulation is securely held without damagingthe structural integrity of the wood deck. When the undersideof the deck is visible, there are no unsightly fasteners pointssticking through.

Concrete Deck:Roof top productivity is greatly increased by using Insta-Stik.No tedious and noisy predrilling required. Compatible withEPS (expanded polystyrene) insulation and wood fiber board,Insta-Stik gives you the ability to choose the right insulationtype for the job.

Metal Deck:Insta-Stik is the smart choice when it comes to metal decks.when the project demands that no fasteners penetrate thedeck due to electrical conduits, exposed underside of deck,thermal bridging concerns, or environmental conditions, thenInsta-Stik is your proven fastener.

Non-compatible ApplicationsNon-compatible Roof Insulation Boards:• Extruded polystyrene• FiberglassNon-compatible Substrates:• Coal tar pitch built-up roofs• Lightweight insulating concrete• Active asphalt

Composition & MaterialsInsta-Stik Professional Roofing Adhesive is a single component,moisture cured polyurethane adhesive. Insta-Stik is free ofconventional solvents. Insta-Stik Complete is supplied in a 30 Lb(14 kg) unit, 23 Lb (10 kg) net chemical weight, with a 4’ (1 m)flexible dispensing hose and two 14" (356 mm) PVC dispensingwands, with coupler. A brass ball valve at the end of thedispensing hose allows operational control for single-handapplication. Insta-Stik Tank Only is supplied in a 30 Lb (14 kg)unit, 23 Lb (10 kg) net chemical weight, with no dispensingequipment. The tank only is ideal for use with the Multi-BeadApplicator.

Accessories:The dispensing of Insta-Stik can be dramatically increased usingthe Multi-Bead Applicator (MBA-28) and Day Pak System(DPS-4) accessory kits. The MBA-28 dispenses 4 equidistantbeads of Insta-Stik within a 4’ (1 m) wide path. Each MBA-28 issupplied with 2 Day Pak Systems. The DPS-4 is the dispensingtubing for the MBA-28. The DPS-4 must be replaced daily orwhenever cured Insta-Stik blocks or restricts flow within thetubing. The use of the MBA-28 is recommended on roof deckswith few penetrations and obstructions.

Limitations• Insta-Stik is not recommended for use with insulation boards larger than 4’ X 4’ (1 m X 1 m).• Insta-Stik is not recommended for residential roofing applications.• Insta-Stik is not recommended for application when surface or ambient temperatures are below 40˚ F (4˚ C) or above 110˚ F (43˚ C).• Insta-Stik is not recommended for use during inclement weather.• Insta-Stik is not recommended for use on wet surfaces.• Insta-Stik is not recommended for use on gravel, excessively dirty, or grease-laden surfaces.• Insta-Stik is not approved for use if the product has expired.• Insta-Stik is not recommended for use on roof decks greater than 2:12 slope. For higher slopes, contact Technical Support.• Insta-Stik is not recommended for use in attaching base sheets and membranes.Flexible Products Company accepts no responsibility forjudging the acceptability of the roof substrate or for theroof systems structural integrity.

Insta-Stik

ProfessionalRoof InsulationAdhesive

INSTA-STIK ROOF ADHESIVEINSTA-STIK ROOF ADHESIVE

75




ApprovalsFactory Mutual (FM):Insta-Stik professional Roofing Adhesive meets the requirements of the followingFM fire and wind uplift resistance tests for FM approved roof deck applications:

Flat• Class 1-60 • Class 1-150 • Class 1-195 • Class 1-240 • Class 1-90 • Class 1-165 • Class 1-210 • Class 1-270• Class 1-135 • Class 1-180 • Class 1-225 Tapered• Class 1-135 • Class 1-165 • Class 1-195 • Class 1-315• Class 1-150 • Class 1-180 • Class 1-240

Insta-Stik has the only industry adhesive approval on tapered systems. Please consult with Technical Support or Flexible Products’ listing in the latest Factory Mutual Approval Guide for details.

Dade County (Florida)Insta-Stik Professional Roofing Adhesive meets the requirements of MetropolitanDade County, Florida, windstorm and fire classifications for roof deck applications.

Insta-Stik is packaged in a single container that should be stored between 45˚ F (7˚ C) and 75˚ F (24˚ C). At these temperatures, the shelf life is 8 months from date of manufacture. The minimum product temperature at the time of application should be 70˚ F (21˚ C). The minimum ambient and surface temperatures must be 40˚ F (4˚ C).

Tensile Adhesion Lap Shear Adhesion Lap Shear Adhesion Peel AdhesionConcrete/Concrete Carbon Steel/Carbon Steel Galvanized Steel/Galvanized Steel To Concrete259 psi (1785 kPa) 342 psi (2356 kPa) 328 psi (2262 kPa) 18 lbf (80 N)Note: Samples cured for 7 days at 75˚ F (24˚ C) 50% RH.

Physical Properties of Insta-Stik Roofing Adhesive

T emperatures Tackfree Time 40˚ F (4˚ C), 50% RH 35 minutes 75˚ F (24˚ C), 50% RH 15 minutes 120˚ F (49˚ C), 25% RH 13 minutes

Insta-Stik Handling Characteristics

Building Height Parapet Perimeter Perimeter Field Ft (m) Wall Height Band Width Application Application In (mm) Ft (m) Rate In (mm) OC Rate In (mm) OC 0-20 (0-6) 0-24 (0-610) 3 (0.9) 6 (152) 12 (305) 25+ (635+) 0 12 (305) 12 (305) 21-40 (6-12) 0-24 (0-610) 6 (2) 6 (152) 12 (305) 25-48 (635-1219) 3 (0.9) 6 (152) 12 (305) 49+ (1245+) 0 12 (305) 12 (305) 41-70 (13-21) 0-24 (0-610) 9 (3) 6 (152) 12 (305) 25-48 (635-1219) 6 (2) 6 (152) 12 (305) 49+ (1245+) 3 (0.9) 6 (152) 12 (305) 71-100 (22-31) 0-24 (0-610) 12 (4) 6 (152) 9 (229) 25-48 (635-1219) 9 (3) 6 (152) 12 (305) 49+ (1245+) 9 (3) 6 (152) 12 (305) 101-200 (31-61) 0-24 (0-610) 12 (4) 6 (152) 9 (229) 25-48 (635-1219) 12 (4) 6 (152) 9 (229) 49+ (1245+) 12 (4) 6 (152) 12 (305) 201-300 (61-91.5) 0-48 (0-1219) 12 (4) 6 (152) 9 (229) 49+ (1245+) 12 (4) 6 (152) 9 (229) 301+ (91.8+) -- 0 6 (152) 6 (152)¹ Coverage is approximately 500-800 ft² (47-74m²) per 23 lb (10 kg) tank of Insta-Stik depending on bead size.

Insta-Stik Application Rates ¹Based On 3/4"-1"(19.1-25.4 mm) Diameter Bead

TECHNICAL DATADOW

INSTA-STIK ROOF ADHESIVEINSTA-STIK ROOF ADHESIVE




Product DescriptionFroth-Pak is a self contained, portable two-component polyurethane foam dispensing system that requires no outside power source and is disposable when empty (consult local authorities for proper disposal).

All Froth-Pak materials have been formulated utilizing either HCFCs or HFCs rather than traditional CFCs. HCFCs are 20 times less hazardous to the environment or the earths ozone layer than CFCs.

Froth-Pak kits are available in a variety of densities in convenient, factory pressurized dispensers sized to facilitate any installation (see Size Table). Kits are supplied complete with gun-hose assembly and standard spray (NS) nozzles. Special purpose nozzles are available as optional extra (see Accessories Table).

Theoretical Yield Density Board Cubic Kit OrderingKit PCF (kg/m3) Feet Feet (m3) Contains InformationFroth-Pak 1.75 (28) 200 16.6 (0.470) One “A" can, one"B" 38 lbs (17.2 kg)/unit 1.75 can, 10 spray nozzles, 30 units/pallet MSHA (28) 7’-6" (2.3 m) gun-hose assembly, wrench, and vaseline pack

Size Table

Backcap Color Nozzle Type Spray PatternYellow Caulking Bead, Ultra fine coverageWhite NS Spray, Small area coverageWhite Fan Fan Spray, Wide area coverage, Spray paint finishGray NS Spray, Small area coverage, Medium outputBlack Pour Pour, High volume filling of large cavities

Other nozzles available - please call for information

Froth-Pak Nozzles (now Anti-Crossover)

Item5-1/2 ft. gun hose assembly7-1/2 ft. gun hose assembly

7-1/2 ft. gun hose assembly with nozzles15 ft. gun hose assembly

15 ft. gun hose assembly with nozzlesInsta-Flo 12 Dispenser (Refill Kits)

Froth-Pak Accessories

ASTM Result Property Test Method 1.75 pcf HCFCFlexural Strength C-203 Parallel, psi 23.0Perpendicular, psi 42.6Apparent K Factor (BTU•in)/(ft2•hr•˚F) Initial C-518 0.143Aged 6 months 0.187Aged 12 months 0.196Aged 18 months 0.204Aged 24 months 0.208Apparent R Value @ 1" (derived from K Factor) --- Initial 7.018 months 4.9Accelerated Service Conditions Procedure “A" D-756 % Volume Change 2.97% Weight Change -1.75Procedure “B" % Volume Change 1.05% Weight Change -2.19Procedure “E" % Volume Change 9.91% Weight Change -2.84Compressive Strength D-1621 Parallel, psi 22.0Perpendicular, psi 8.4Apparent Density, pcf D-1622 1.70Water Absorption (% water base) D-2842 2.5Dimensional Stability (% volume change) D-2126 100˚ F/100% RH, 1 week 0.38100˚ F/100% RH, 2 weeks 0.91158˚ F/100% RH, 1 week 15.57158˚ F/100% RH, 2 weeks 14.02-40˚ F/amb RH, 1 week -0.40-40˚ F/amb RH, 2 weeks -0.04-100˚ F/amb RH, 1 week -3.70-100˚ F/amb RH, 2 weeks -1.13158˚ F/amb RH, 1 week 3.70158˚ F/amb RH, 2 weeks 3.65212˚ F/amb RH, 1 week 1.48212˚ F/amb RH, 2 weeks 1.16Open Cell Content D-2856 <8%Tensile Strength D-1623 Parallel, psi 40.1Perpendicular, psi 27.2Shear Strength C-273 Parallel, psi 23.9Perpendicular, psi 19.8Water Vapor Transmission (perm-in) E-96 3.0* Tests performed by Insta-Foam Products, Inc. NVLAP Accredited Lab for 11 ASTM tests.Copy of test report available upon request.

Typical Physical Properties*

FROTH-PAK

Two-ComponentSpray PolyurethaneFoam System

DOW

FROTH-PAK POLYURETHANE FOAMFROTH-PAK POLYURETHANE FOAM

77




Technical DataFroth-Pak 1.75-25FS MSHA conforms to building code requirements for a Class 1 foam. When tested to ASTM E-84, the flame spread is 25 and the smoke developed is 350 at 2" (50 mm) thickness with full coverage.

Froth-Pak 1.75-25FS MSHA also conforms to Mine Safety and Health Administration (MSHA) surface flame spread requirement ASTM E-162 (flame spread index of 25 or less).

These tests do not purport to address all of the safety problems, if any, associated with it’s use.

Warning:The foam produced by Froth-Pak is organic and is combustible and may constitute a fire hazard if improperly used.

InstallationFor best results, remove any lose debris, dirt, dust or other deleterious material from surfaces.

Also, best results are obtained when chemical temperatures are 75˚ F (24˚ C).

Every Froth-Pak kit is self-contained and ready to use. Kits are factory pressurized and require no outside power source. With it’s convenient dispensing design, Froth-Pak simplifies set-up and use. Typically, a Froth-Pak kit consists of one "A" and one “B" cylinder in one carton plus a hose assembly and accessories.

ApplicationEvery purchase of a Froth-Pak kit includes “Operating Instructions". A Material Safety Data Sheet is available upon request. Read all information and cautions before using Froth-Pak. “Operating Instructions" include information on operation, trouble shooting, yield, application tips, quality control, curing, storage, disposal, first aid, and similar information.

PrecautionsAvoid contact with eyes and skin. ALWAYS wear protective eyewear, gloves, and clothing when operating. Use ONLY with adequate ventilation or NIOSH-certified respiratory protection. In unventilated areas, DO NOT remove respirator for AT LEAST 15 MINUTES after use. CONTENTS UNDER PRESSURE. To avoid possible explosion or fire, DO NOT puncture or incinerate. DO NOT refill or repressurize. DO NOT expose cylinders to temperatures above 120˚ F (49˚ C). The foam produced is combustible. DO NOT expose to heat, sparks or open flame. This product is NOT intended for use in applications where temperatures exceed 250˚ F (121˚ C). Store at temperatures between 60˚ F and 80˚ F (16˚ C and 27˚ C).

DOW

FROTH-PAK POLYURETHANE FOAMFROTH-PAK POLYURETHANE FOAM




TILE BOND®

The Preferred Adhesive ForRoof Tile Installation

Fast, Trouble-Free, Lightweight, Convenient,And Hurricane-ProvenProduct Description/ApplicationTile Bond® is a polyurethane adhesive used for adhering roofing tile toapproved commercial or residential roof deck underlayments. This portable,disposable one component polyurethane adhesive provides superiorattachment strength over other methods and can be used for new, reroofand tile roof repair applications. It reduces tile breakage and material costswhile eliminating the need to purchase, transport and maintain heavyequipment.

Tile Bond makes installing and repairing residential or commercial tile roofsquick and easy, reducing labor costs and eliminating nailing on roofs withpitches up to 6:12. The 23 lb (10 kg) canister will adhere approximately 750field tiles. The 20 oz (568 g) can will adhere approximately 40 field tiles.

SizesTile Bond is available in a 23 lb (10 kg) canister complete kit which includes adispenser with hose, 9/16" (14.3 mm) wrench, foam backer rod to illustrateproper patty size, and an instruction sheet. It is also available in a convenient20 oz (568 g) can for quick and easy use.

Approvals:• UL Class 1 listed (ASTM E84)• Class A rated (ASTM E108)• South Florida Building Code, Broward County, 1999 Edition• Metro-Dade County Acceptance #99-0412.04 (Expires 10/01/01)• SBCCI Evaluation Report #9744A (Refer to this evaluation report for code compliance.)

Installation:Tile bond will adhere to the following roof tile types:• 2 piece barrel profile• High profile• Medium profile• Low/flat profile

DOW

ROOF TILE ADHESIVEROOF TILE ADHESIVE

79




INSULATION ADHESIVEINSULATION ADHESIVE




Product Name Body Type / Thickness Flange Diameter Clamping Ring Strainer Dome Type Roof System Type NotesPC/PET RetroDrain One piece PC/PET 13.9" PC/PET PC/PET Compatible with Patented design

injection molded .150" all types built-in patented Olympic U-Flow Seal

Aluminum Hercules One piece spun aluminum 17.5" Cast Aluminum, PC/PET Compatible with Includes patented .125" (11 gauge) Aluminum or SuperDome® all types Olympic U-Flow Seal

SuperDome One piece PC/PET 13.9" PC/PET SuperDome® Compatible with Patented design RetroDrain injection molded .150" all types built-in patented Olympic U-Flow Seal

US-II RetroDrain One Piece spun aluminum 17.5" None Aluminum Compatible with Includes patented .064" (16 gauge) or PC/PET all types except pitch Olympic U-Flow Seal

PVC AlumaWeld One Piece spun aluminum 17.5" None Aluminum Compatible with Plastisol flange or .064" (16 gauge) or PC/PET PVC welding of PVC membranes. Includes Olympic U-Flow Seal

TPO RetroWeld One piece TPO 13.9" PC/PET SuperDome® Compatible with TPO Hot air weldable flange injection molded .150" or PC/PET and EP Membranes for TPO and EP membranes. Includes Olympic U-Flow Seal

Copper Tig welded copper 17.5" Cast Aluminum, PC/PET Compatible with Includes patented Hercules .032" (3,4") Aluminum or SuperDome® all types Olympic U-Flow Seal .050" (5 &6")

Aluminum One piece spun aluminum 12.5: Cast Aluminum, PC/PET Compatible with New construction

Classic .125" (11 gauge) Aluminum or SuperDome® all types applications. No compression seal

Drain Selector Guide

aluminum hercules

U-Flow Seal Flow Control

OverFlow

QuickFlow

ROOF DRAINS BY OMGROOF DRAINS BY OMG




81

FASTENERSFOR

COMMERCIAL DRYWALL

TFC offers the largest selection of fasteners for the commercial drywall Industry. Need it now?

Ask us to about our NEED-IT-NOW! trade specific product program for commercial drywall construction.

Contact our product specialists who are trained to support you with a wide variety of standard and specialty fasteners for your application.

We specialize in fastening solutions for those difficult connections, and all of our fasteners are designed for the professional construction trades assuring high performance and long-life.

�Fastening recommendations �Job site support �Product testing �Pricing Programs




82

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 10 x 1 1/2" 3/4" - 1" 5

TRACER® Type “G"Attachment or lamination of layered drywall.

Hi-Lo® Sharp PointAttachment of drywall to steel stud up to 20 gauge (.036).

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 7 x 1" 3/8" - 5/8" 10 7 x 1 1/8" 3/8" - 3/4" 8 7 x 1 1/4" 3/8" - 7/8" 8 8 x 1 5/8" 1/2" - 1 1/4" 5 8 x 1 7/8" 3/4" - 1 1/2" 4 8 x 2 1/4" 1 1/16" - 1 7/8" 2.5 8 x 2 5/8" 1 3/8" - 2 1/4" 2.5 8 x 3" 1 7/8" - 2 5/8" 2

Carton Size/Length Quantity (M) 7 x 7/16" 10

TRACER® Pan HeadAttachment of steel stud to steel track or for splicing steel stud up to 20 gauge (.036") total thickness.

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 6 x 1" 3/8" - 5/8" 10 6 x 1 1/8" 3/8" - 3/4" 10 6 x 1 1/4" 3/8" - 7/8" 8 6 x 1 5/8" 3/8" - 1 1/4" 5 6 x 2" 1" - 1 5/8" 3.5 6 x 2 1/4" 5/8" - 1-7/8" 3 7 x 2 1/2" 7/8" - 2 1/8" 2.5 8 x 3" 1 3/8" - 2 5/8" 2 10 x 3 1/2" 1 10 x 4" 1 10 x 4 1/2" 1 10 x 5" .5 10 x 6" .5

TRACER® Flat Bugle HeadAttachment of drywall to steel stud up to 20 gauge (.036").

Phos and oil

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 6 x 1" 3/8" - 5/8" 10 6 x 1 1/8" 3/8" - 3/4" 10 6 x 1 1/4" 3/8" - 7/8" 8 6 x 1 5/8" 3/8" - 1 1/4" 5 6 x 2" 1" - 1 5/8" 3.5 6 x 2 1/4" 5/8" - 1 7/8" 3 7 x 2 1/2" 7/8" - 2 1/8" 2.5 8 x 3" 1 3/8" - 2 5/8" 2 10 x 3 3/4" 2 10 x 4" 1 10 x 4 1/2" 1 10 x 5" .5 10 x 6" .5

TRACER® Coarse Type “W"Attachment of drywall to wood stud or framing.

Phos and oil

Phos and oil

TRACER® Trim HeadAttachment of drywall to steel stud up to 20 gauge (.036").

Phos and oil

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 6 x 1 5/8" 1/2" - 1 1/4" 5 6 x 2 1/4" 5/8" - 1 7/8" 3 6 x 3" 3/4" - 2 5/8" 2

Phos and oil

Need additional corrosion protection?

Now available with our TRI-SEAL™ coating for treated lumber applications!

Size: #6 x 1-1/4" GP Coarse thread. Phillips bugle head.1,000 hrs salt spray

Wood or Metal

TRACERDRYWALL SCREWSYWALL SCREWS

TRACERTRACER® ® DRYWALL FASTENERSDRYWALL FASTENERSWOOD OR METALWOOD OR METAL




83

Pullout Strength (LBS.ULT.) Embedment in 2x4 Stud Grade S.Y.Pine

Fastener Description 1/2" 3/4" 1" 1-1/4" 6-10 Tracer Coarse 182 328 422 620 6-18 Tracer Fine 160 290 400 586 7-9 Tracer Coarse 189 318 440 630 7-16 Tracer Fine 172 288 408 590 8-9 Tracer Coarse 186 290 502 645 8-15 Tracer Fine 179 278 490 651

Pullout Strength (LBS.ULT.)Steel Gauge

Fastener Description 26 24 22 20 18 16 14 7-19 Tracer Hi-Lo 129 178 244 277 8-18 Tracer Hi-Lo 163 242 314 370 6-18 Tracer Fine 122 168 228 288 7-16 Tracer Fine 142 199 265 302 8-15 Tracer Fine 134 235 289 351 6-20 Tracer D.S. 120 183 248 296 471 679 847

Torsional Shear Tensile Strength Strength Strength Product Thread Thread Dia. Root Dia. Root Area Ultimate Stress Tensile Ultimate Ultimate Type DIA. Per Inch (Nom.) (max.) (Sq.In.) (lb s.) (P.S.I) (lbs. - in.) (lbs.) Tracer Coarse 6 10 .151 .092 .0082 1422 173,414 24 938 Tracer Fine 6 18 .139 .092 .0066 1322 200,303 24 1015 Tracer DS 6 20 .142 .105 .0086 1500 174,418 24 775 Tracer Coarse 7 9 .164 .102 .0082 1430 192,195 26 773 Tracer Fine 7 16 .155 .107 .0089 1576 177,078 26 1238 7 19 .153 .095 .0070 1398 199,714 42 880 Tracer Coarse 8 9 .177 .110 .0094 1540 163,829 42 902 Tracer Fine 8 15 .165 .116 .0105 1802 171,619 42 1387 Tracer Hi-Lo 8 18 .167 .100 .0078 1430 183,333 45 925

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 6 x 1" 3/8" - 5/8" 10 6 x 1 1/8" 3/8" - 3/4" 10 6 x 1 1/4" 3/8" - 7/8" 8 6 x 1 5/8" 3/8" - 1 1/4" 5 6 x 1 7/8" 3/8" - 1 1/2" 4 6 x 2" 3/8" - 1 5/8" 4 6 x 2 3/8" 3/8" - 2" 2.5 6 x 2 5/8" 3/8" - 2 1/4" 1.6 6 x 3" 3/8" - 2 5/8" 1.4

TRACER® D.S. Bugle HeadAttachment of drywall to steel stud up to 14 gauge (.075).

Zinc plated

Drywall Thickness Carton Size/Length Minimum-Maximum Quantity (M) 6 x 1 5/8" 1/2" - 1 1/4" 5 6 x 2 1/4" 5/8" - 1 7/8" 3

TRACER® D.S. Trim HeadAttachment of wood trim thru drywall to steel stud up to 14 gauge (.075).

Zinc plated

Size/Length 8 x 1 1/4" 8 1 5/8" 8 x 2-1 /4"

TRACER® CB Cement BoardAttachment into wood or metal up to 18 gauge.

Long life coated

The values listed are ultimate averages achieved under laboratory conditions. An appropriate safety factor must be applied to these values by the user to achieve a design load.

Performance CharacteristicsTracer Drywall Fastening Systems

Need additional corrosion protection?

Now available with our TRI-SEAL™ coating for treated lumber applications!

Size: #6 x 1-1/4" DP2. Phillips bugle head.1,000 hrs salt spray

Metal

TRACERTRACER® ® DRYWALL FASTENERS - METALDRYWALL FASTENERS - METALTRACERDRYWALL SCREWSYWALL SCREWS




Carton Size/Length Quantity (M) 6 x 7/16" 10 8 x 1/2" 10 8 x 1" 10

TRACER® D.S. Pan FramerAttachment of steel stud of steel track or for splicing steel stud up to 14 gauge (.075") total thickness.

Carton Size/Length Quantity (M) 8 x 1/2" 10 8 x 3/4" 5 8 x 1 1/4" 10

TRACER® D.S. Round Washer HeadAttachment of wood trim thru drywall to steel stud up to 14 gauge (.075").

.00015" zinc plated zinc plated


.0003" zinc and yellow

.0003" zinc plated.0003" zinc and yellow

.0003" zinc plated with long life coating.Finish: .0003" min. electro zinc plated with flouropolymer topcoat.

Corrosion results: 1,000 hrs. salt spray

Applications: Drilling and tapping up to .210" thick steel.


Size/Length Head Type 8-16 x 5/8" DP2 Phillips pan

BLAZER® Pan HeadFastener for steel framing applications.

Size/Length Head Type 10-16 x 5/8" DP3 #2 square recess pancake

BLAZER® Lo ProfilePancake HeadFastener for steel framing applications.

Size/Length Head Type 10-24 x 5/8" DP3 #2 Sq.Phil recess high torq pancake

BLAZER® Lo Profile High Torq Pancake Head #2 Sq.Fastener for steel framing applications.

Size/Length Head Type 10-16 x 5/8" DP3 5/16" Hi-Hex 10-16 x 3/4" DP3 design

BLAZER® Hi-HexFastener for steel framing applications.With serration.

Size/Length Head Type 12-14 x 7/8" DP3 5/16" Hex washer head

BLAZER® Long-PilotLong pilot section allows the fastener to complete the drilling before tapping occurs, eliminating drill point failures.

Size/Length Head Type 12-24 x 1 1/4" DP5 5/16" HWH heavy gauge up to 1/2"

BLAZER® Heavy GaugeFastener for steel framing applications.

For technical data, refer to page 12.

STRESS-LESS® Framing ScrewFastener for steel framing applications with high stress concentrations. Drill and tap uo to 1/4" steel!

Size/Length Head Type 1/4-14 x 7/8" DP3 5/16" Hex washer head

Epoxy Coated

STEEL FRAMING FASTENERSSTEEL FRAMING FASTENERS

85




TRACER CB CEMENT BOARD SCREWTRACER CB CEMENT BOARD SCREW




SPECIALTY STAINLESS STEEL SCREWS SPECIALTY STAINLESS STEEL SCREWS FOR MULTI-PURPOSE USEFOR MULTI-PURPOSE USE

87




SPECIALTY STAINLESS STEEL SCREWS SPECIALTY STAINLESS STEEL SCREWS FOR MULTI-PURPOSE USEFOR MULTI-PURPOSE USE




GAS CHARGED TOOLSGAS CHARGED TOOLSTRAKFAST®TRAKFAST®

89




SIZESGAS CHARGED TOOLSGAS CHARGED TOOLS

TRAKFAST®TRAKFAST®




SIZESPIN AND CLIPPIN AND CLIPTRAKFAST®TRAKFAST®

91




SIZESPIN AND CLIPPIN AND CLIPTRAKFAST®TRAKFAST®





TRAKFAST PINSPULLOUT LOADS / CONCRETE ANDHOLLOW BLOCK

93





TRAKFAST PINSPULLOUT LOADS / CONCRETE ANDHOLLOW BLOCK





TRAKFAST PINSPULLOUT LOADS / PLYWOOD TO STEEL

95





TRAKFAST PINSPULLOUTS LOAD / PLYWOOD TO STEEL




.25 caliber 10-shot disc loads 2 (Brown) 3 (Green) 4 (Yellow) 5 (Red)

Weight 4 1/2 pounds

Height 7 1/2 inches

Length 15 inches

Muzzle bushing O.D. 5/8"

Pin capacity 2 or 2 1/2" washered• Most durable, powerful powder tool.

• Designed fir high-production use in steel and concrete.

• Semi-automatic.• 2" pin capacity (2 1⁄2" w/washer).• 5-year warranty (10-year warranty

on muzzle bushing).

• Ramset’s patented red disc gives you the power you need.

• Fasten into the hard est of concrete and steel with a red disc load and the D45A. The patented 10-shot disc load advances only after firing which eliminates wasted loads.

Specifications

.22 caliber Single-shot loads 1 (Gray) 2 (Brown) 3 (Green) 4 (Yellow)

Weight 4.3 pounds

Length 13 1/2 inches


Pin capacity 1 1/2"

Factory Mutual System approved

• Single shot.• 1 1/2" pin capacity.• 5-year warranty.

• .22 caliber “A" crimped powder loads in four power levels (gray, brown, green, yellow).

Specifications

.25 caliber 10-shot disc loads 2 (Brown) 3 (Green) 4 (Yellow)

Weight 4.9 pounds

Length 12 1⁄2 inches


Pin capacity 2 3/8"

• Quick power adjustment.• Gives eight levels of power

with only one load level for a variety of applications.

• Semi-automatic.• 2 3/8" pin capacity (2 1⁄2" w/washer).

• 5-year warranty.• Patented 10-shot disc loads

advance automatically, eliminating wasted loads.

Specifications

N.E.C. Code 300.11 (Independent Hanging Wires Required)

Means you need fast, frequent fastening to get your job done before a ceiling contractor closes up.

Complies with OSHA and ANSI standards.

D45A

721

D60

POWER ACTUATED FASTENINGPOWER ACTUATED FASTENING

97




.27 caliber 10-shot strip loads 3 (Green) 4 (Yellow) 5 (Red)

Weight 5 3/4 pounds

Length 15 inches


Pin capacity 2 1/2" (3" w/washer)

• Semi-automatic• 2 1/2" pin capacity (3" w/ washer)• 5-year warranty• Uses Loadsaver™ 10-shot strip load

Specifications

Complies with OSHA and ANSI standards.ICBO Evaluation Service, Inc. – #ER-1147 (for sill plate applications)


Weight 4.5 pounds

Pin capacity ceiling clips 1 1/4"

Length 17 inches

Specifications


.22 caliber crimped loads 4 (Yellow) 5 (Red)

Weight 2.8 pounds

Height 13 inches


1 Ejection pin

2 Barrel

3 Gas expansion chamber

4 Cartridge and chamber

5 Clip assembly

• Single shot.• .22 caliber crimped loads.• It is important to use only

loads specifically designed for use in the L1600 tool.

• Preassembled clip & pin speeds installation and reduces labor cost.

• Sturdiest clip on the market for improved pullover performance

• Accurate, positive attachment of hanger wire from concrete ceilings and steel.

• Elongated wire hole allows for freedom of movement of wire loop.

• 9/32" hole allows pencil rod to be suspended.

•No need for ladders or scaffolding with the LADD Fastening System.

1 2 3 4 5

SA270

Viper• Semi-automatic.• 30% faster overhead attachment.• 5-year warranty (10-year warranty on muzzle bushing).• Uses Loadsaver™ 10-shot strip load.

L1600 LADD Overhead Fastening System





Weight 4 1/2 pounds

Length 13 1/4"



Pin capacity 2 1/2" (3" w/washer)

Cobra

• Semi-automatic.• 2 1/2" pin capacity (3" w/washer).• Uses Loadsaver™ 10-shot strip loads.• Low velocity piston drive tool provides added safety on the

job

Specifications

.27 caliber Long single-shot loads 4 (Yellow) 5 (Red) 6 (Purple)

Weight 6 3/4 pounds

Length 15 inches


Pin Capacity 3"

MD380

• Single shot.• 3" pin capacity.• 5-year warranty.• .27 caliber long “A" crimped powder loads in three power

levels (yellow, red, purple).

Specifications

Factory Mutual System approval


99




Material 3/16" 1/4" 3/8" 1/2" 3/4" 1/4" Plywood SP58* SP34* SP78** SP78** SP78** 3/8" Plywood SP58* SP34* SP78** SP78** SP78** 1/2" Plywood SP100** SP100** SP100** SP100** SP100** 3/4" Plywood SP114** SP1 14** SP1 14** SP1 14** SP1 14** 2' x 4' Plate SP178** SP178** SP178** SP178** SP178** 10 ga. to 12 ga. SP58* SP34* SP34* SP78** SP58** 13 ga. to 17 ga. SP12* SP58* SP34* SP34** SP58** 18 ga. to 25 ga. SP12* SP58*

PowerPoint™ Pins for Hard Concrete and Steel FasteningSelection Chart for Base Steel Thickness

* For use with all Ramset Powder Tools ** For use with all Ramset Powder Tools except the Model 721

Part Shank Length Auto D45/ Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70 1503KBC 1/2 knurled (12.7) √ √ √ √ √ √ √ 1506BC 3/4 (19.1) √ √ √ √ √ √ √ 1508BC 1 (25.4) √ √ √ √ √ √ √

Black Track Pins

Selection Chart

Shank diameter = .145

Part Number Nom. Shank Diameter Shank Length In. Shank Length mm Box Qty. SP12 .150 1/2 (12.7) 100 SP58 .150 5/8 (15.9) 100 SP34 .150 3/4 (19.1) 100 SP78 .150 7/8 (22.2) 100 SP100 .150/.180 1 (25.4) 100 SP1 14 .150/.180 1-1/4 (31.8) 100 SP1 12 .150/.180 1-1/2 (38.1) 100 SP178 .150/.180 1-7/8 (47.6) 100

Selection Chart for Product

For optimum results in hard steel, use the D45 powder actuated tool.

• .300 head diameter drive pins.• Designed for use in concrete and structural

steel applications.• Available in 100 or 1000 pack.

The special black coating improves pin penetration into difficult base material (i.e. hard concrete). We offer this black coating on all of our fasteners manufactured for the attachment of drywall track and channel to concrete and steel.

Part Shank Length Auto D45/ Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70 1503K* 1/2 Knurled (12.7) √ √ √ √ √ √ √

1506* 3/4 (19.1) √ √ √ √ √ √ √

1508* 1 (25.4) √ √ √ √ √ √ √

1510* 1-1/4 (31.8) √ √ √ √ √ √ √

1512 1-1/2 (38.1) √ √ √ √ √ √

1513 1-3/4 (44.5) √ √ √ √ √ √

1514 2 (50.8) √ √ √ √ √ √

1515 2-3/8 (60.3) √ √ √ √ √

1516 2-1/2 (63.5) √ √ √ √

1524 3 (76.2) √ √

Drive Pins

Selection Chart

* Also available in 1000 Pack Shank diameter = .145

• .300 head diameter drive pins.• Designed for use in concrete and structural steel applications.• 100 pin pack.

DRIVE PINSDRIVE PINS




Part Shank Length Auto D45/ Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70 1506SD 3/4 (19.1)

1508SD 1 (25.4)

1510SD 1-1/4 (31.8)

1512SD 1-1/2 (38.1)

1514SD 2 (50.8)

1516SDC 2-1/2 (63.5)

1524SDP* 3 (76.2)

Drive Pins

Selection Chart

* Square washer indicates 3" pin has been installed Shank diameter = .145

• .300 head diameter drive pins with 7/8" washer.• Washer increases bearing surface against the material to be fastened.• 100 pin pack.

Part Shank Length AUTO D45/ Number In. (mm) 721 FAST D60 SA270 D45A Cobra M70 1903K 1/2 Knurled (12.7)

1906 3/4 (19.1)

1906M 3/4 (19.1)

1908 1 (25.4)

1908M 1 (25.4)

Top Hat Drive Pins

Selection Chart


• .300 head diameter top-hat.• Increases the bearing surface against the material to be fastened for improved attachment to

inconsistent base materials in 100 pin pack and 1000 pack.

Part Shank Length Auto D45/ Number In. (mm) 721 Fast D60 SA270 D45A Cobra M70 SP12 1/2 (12.7)

SP58 5/8 (15.9)

SP34 3/4 (19.1)

SP78 7/8 (22.2)

PowerPoint Pins

Selection Chart


• Premium steel and hard concrete pin.• Pin for fastening into harder steel and concrete.• 100 Pin Pack

Part Shank Length Auto D45/ Number In. (mm) Fast D60 SA270 D45A Cobra M70 SP100 1 (25.4) s s s s s s SP114 1-1/4 (31.8) s s s s s s SP112 1-1/2 (38.1) s s s s s s SP178 1-7/8 (47.6) s s s s s s

PowerPoint Step Shank Pins

Selection Chart


• Premium steel and hard concrete pin.• Pin for fastening into harder steel and concrete.• 100 pin pack.

DRIVE PINSDRIVE PINS

101




Part Thread Shank Length Number Length In. (mm) Auto D45/ In. (mm) 721 Fast D60 SA270 *D45A Cobra M70 Viper 1623WK 3/4 (19.1) 1/2 knurled (12.7)

1642W 1/2 (12.7) 1 (25.4)

1643W 3/4 (19.1) 1 (25.4)

1644W 1 (25.4) 1 (25.4) 1653W 3/4 (19.1) 1 1/4 (31.8)

Threaded Studs

Selection Chart


Part Pin Length Auto D45/ Number In. (mm) 721 Fast D60 SA270 D45A Cobra Viper SDC100 1 (25.4)

SDC125* 1 1/4 (31.8)

Selection Chart

* Available in 100-Pack Shank diameter = .145

• For applications that require removability, where shimming is required.

Part Thread Length Shank Length Number In. (mm) In. (mm) MD380 9140K 1 (25.4) 5/8 knurled (15.9)

9150 1 (25.4) 1 1/16 (27.0)

9190 1 (25.4) 1 1/4 (31.8)

3/8"-16 Threaded Stud

Selection Chart


Part Description Auto D45/ Number 721 Fast D60 SA270 D45A Viper* 2202 Ceiling Clip w/1 1/4"

Ceiling Clip Assemblies

Selection Chart

* Viper tool comes assembled with the 2VP4125 nosepiece. Shank diameter = .145

• .300 head diameter pin.

• Fastener is preassembled to 14 gauge angle clip for applications such as the hanging of ceiling wireto support ceiling grid.

• Available in 1000 pack only.

DRIVE PINS AND CLIPSDRIVE PINS AND CLIPS




Part Pin Length Auto D45/ Number In. (mm) Fast D60 SA270 D45A Cobra Viper SPC78 7/8 (22.2)

SPC114 1 1/4 (31.8)

PowerPoint Pins with Ceiling Clip

Selection Chart

• .300 head diameter pin for hard concrete.

SPC78 shank diameter = .150 SPC114 shank diameter = .150/.180

Part Description Auto D45/ Number 721 Fast D60 SA270 D45A Cobra M70 Viper 38BXSP78C 3/8" bx clip with 7/8" pin

12EMTSP78C 1/2" conduit clip with 7/8" pin

34EMTSP78C 3/4" conduit clip with 7/8" pin

Conduit Clip Assemblies

Selection Chart

.300 Head Diameter Pin• Fastener is preassembled to conduit clip to attach electrical conduit to concrete or steel.



Part Description Number 1202CF Angle clip (no pin)

Fastener Angle ClipSelection Chart

Part Pin Length Description Number In. (mm) L652 1 1/4 (31.8) Preassembled pin & clip

Ladd Assembly for L1600Selection Chart

DRIVE PINS AND CLIPSDRIVE PINS AND CLIPS

103




T ool Part Power Case Caliber/ Model Number Level Color Color Type Packaging D60/D60L 2D60 2 Brown Brass .25 Disc 10 Discs/Box D45/D45A 3D60 3 Green Brass .25 Disc 10 Discs/Box AutoFast 4D60 4 Yellow Brass .25 Disc 10 Discs/Box D45/D45A and AutoFast 5D45 5 Red Brass .25 Disc 10 Discs/Box 721 12CW 1 Gray Brass .22 Single 100/Box 4170 32CW 3 Green Brass .22 Single 100/Box M70 42CW 4 Yellow Brass .22 Single 100/Box SA270 3RS27 3 Green Brass .27 Strip 10 Strips/Box Cobra 4RS27 4 Yellow Brass .27 Strip 10 Strips/Box Viper 5RS27 5 Red Brass .27 Strip 10 Strips/Box MD380 4RL27 4 Yellow Brass .27 Single 100/Box 5RL27 5 Red Brass .27 Single 100/Box 6RL27 6 Purple Brass .27 Single 100/Box L1600 L674 4 Yellow Brass .22 Single 100/Box

High Quality and DependabilityRamset Loads for Low Velocity Tools

T ool Part Power Case Caliber/ Model Number Level Color Color Type Packaging DX-350, DX-351 3RS27 3 Green Brass .27 Strip 10 Strips/Box 4RS27 4 Yellow Brass .27 Strip 10 Strips/Box DX-350, DX-351 DX-36M, DX-451 5RS27 5 Red Brass .27 Strip 10 Strips/Box DX-451 6RS27 6 Purple Brass .27 Strip 10 Strips/Box DX-600N 4RL27 4 Yellow Brass .27 Single 100/Box 5RL27 5 Red Brass .27 Single 100/Box 6RL27 6 Purple Brass .27 Single 100/Box DXE37 12CW 1 Gray Brass .22 Single 100/Box DXE72 22CW 2 Brown Brass .22 Single 100/Box 32CW 3 Green Brass .22 Single 100/Box 42CW 4 Yellow Brass .22 Single 100/Box

Ramset Loads for Hilti Tools

1000-Pak/100 Strips/Box Hilti® is a registered trademark of Hilti Corp.

POWDER LOADSPOWDER LOADS




POWER ACTUATED FASTENINGPOWER ACTUATED FASTENINGTECHNICAL DATA TECHNICAL DATA

PULLOUT LOADS IN CONCRETE

105




POWER ACTUATED FASTENINGPOWER ACTUATED FASTENINGTECHNICAL DATA TECHNICAL DATA

PULLOUT LOADS IN STEEL AND CONCRETE




•Pin and clip combos•Angle clips

•Angle clips with self-drillers•Angle clips with Tapcons

•Acoustical toggle bolts •Acoustical eye lags

•2-1/2" timber pin and clips•Caddy Clips

Fasteners and ClipsPin and ClipFor metal wood orconcrete applications*Concrete pins*Stepdown steel pins*2-1/2" Timber pins

Self-drillingUse in steel deckapplications1/4 x 2"1/4 x 2-3/4"

Wedge AnchorUse in concreteapplications.Contact TFC for a size tomeet your specificrequirement.

Structural Attachment Clips

ToggleSupplied with nut,washer, and toggle1/4-20 x 4"1/4-20 x 5"

LagUse in woodapplications1/4" x 3"1/4" x 4"1/4" x 5"

We can assemble and tie the wire to a specific fastener

BLAZER® Self-drillingUse in metalapplications up to 1/2" thick#10 x 3/4" DP3#12-14 x 1" DP3#12-24 x 7/8" DP4#12-24 x 1-1/4" DP5

TAPCON®

Use in concreteapplications3/16" x 1-1/4" & 1-3/4"1/4" x 1-1/4" & 1-3/4"HWH

Choose a wire from our standard lengthsWire size and load capacity

12 gauge (.105") ..... Ultimate weight capacity of 600 lbs.* 9 gauge (.147") ..... Ultimate weight capacity of 1,190 lbs.

Wire lengths (Custom lengths available)

4 foot - 6 foot - 8 foot - 12 foot - *16 foot* Available upon request

Clip-PurZ-purlin applications

J-ClipOpen web bar joist applications(1/16" to 1/4" flange)

J-Master Tool for installingClip-Pur and J-Clip

Clip-Pur and J-Clip are tradenames of ITW Ramset

It’s time to get twisted!Are you looking for complete selection of standard and custom pre-tied wires? Triangle Fastener is the source!

We offer a full line of pre-tied wires for fastening into metal, wood, or concrete. Our fasteners, clips, and tools assure a positive connection and easy installation.

With our in-house production, we produce high quality ties and quick delivery.

In Stock for Immediate Shipment!

TWISTER PRE-TIED WIRESTWISTER PRE-TIED WIRES

For load values of fasteners, refer to the appropriate product page for the item listed.

We can assemble most fasteners for your specifi c need!

107




J-Master Tool® -L1700For attachment of J-Clip® (L1701) and Clip-Pur® (L1801) Hanger Wire Clips.

Clips Used With the J-Master Tool®

J-Clip® (L1701)• Strong, reliable attachment of

pre-tied hanger wire.• Use for open web bar joists or

purlins.• Each clip fits 1/16"-1/4" flanges.

1. Attach a 1/2" pipe extension (dielectric pole available) to the threaded end of a J-Master tool, and place pre-wired J-Clip into tool.

2. Insert the J-Clip up into the void between the two base angles. Position the clips over the vertical flange and pull down.

3. Disengage the tool by lifting up and out.

Clip-Pur® (L1801)• Fast, easy attachment of pre-tied

hanger wire from Z-Purlins.• Disengages from J-Master tool

after installation.• Two magnetic strips attached to

J-Master tool make installation easy.

1. Attach J-Master tool to end of threaded 1/2" pipe or dielectric pole. Lay pre-tied Clip-Pur against magnetized strips.

2. Raise the Clip-Pur up to the purlin. Position the clip on the 45° flange and give a downward tug, the clip is now in position.

3. Disengage the tool by lifting up and out.

J-Clip attached to the J-Master Tool

Clip-Pur attached to the J-Master Tool

Easy Installation

PURLIN AND BAR JOIST CLIPSPURLIN AND BAR JOIST CLIPS




Extension PolesQuality Ramset extension poles provide the convenience of using powder actuated tools for overhead fastening without the need for scaffolding or ladders.

ApplicationsRamset Pole Tools are an excellent choice for high-reach fastening applications.

Fast, easy installation from floor level eliminates lift baskets, scaffolds and ladders.

Part Numbers For Ramset ToolsPTSEMI6 (6’) and PTSEMI8 (8’) for use with: D60—our premier semi-automatic tool, featuring power level adjustment

and no-waste disc loads. SA270—high-quality .27 caliber strip tool for general purpose applications. D45A—most durable, high-power, semi-automatic tool for hard concrete

and steel applications. MD380—popular 3/8" head diameter tool. 721 The industry preferred tool for the drywall trade.PTSEMI6 (6’) and PTSEMI8 (8’) for use with: CobraVIPER Fixed-length Telescoping extension poles extension poles adjustable in 1 foot increments 6’ #VPOL6 6’-12’ #TVPOL612 8’ #VPOL8 6’-18’ #TVPOL618

Top-quality hand lever and cable system requires only 15 pounds of pressure so cable doesn’t stretch

Lightweight cast aluminum housing fits tool snugly and provides tool protection

Trigger bar adjusts easily for individual tools

Nyloc™ nuts keep your adjustment fixed solidly on the trigger bar

Delrin™ coupler on cable makes pole di-electric

Encased cable runs length of pole and connects hand lever with trigger—no rods to bend inside

Rubber “motorcycle" grip for operator comfort and to reduce recoil level

Teflon™coated cable reduces drag and less wear on user’s hand

Can be used with various Ramset actuated tools

Use with Twister Pre-Tied Wire!

OVERHEAD POWDER ACTUATED FASTENINGOVERHEAD POWDER ACTUATED FASTENING

109




Lagmaster Plus™ is the electrician’s pole tool. The unique plug-in heads make it the most efficient tool of its kind. It increases safety by keeping your men on the floor. Use it to install ceiling wire, jack chain, threaded rod, smooth rod and overhead screw installation. Power the pole with any 3/8" or 1/2" battery operated or corded drill.

One pole - many applications!

Choose from five different adjustable length models:• LM-6 Double 3’ (11’ ceilings) • LM-18 Triple 6’ (24’ ceilings)• LM-12 Double 6’ (18’ ceilings) • LM-24 Triple 8’ (30’ ceilings)• LMG-12 Triple 4’ (18’ ceilings)

Insert the eye lag screw into secured wire plug. Insert the wire through the hole and

bend the tail down.

Secure a #1 1/2 “S" hook to an acoustical eye lag and to the proper size chain for your

job. Insert it into the LagMaster Plus™.

Plug in the LagMaster Plus™ 1/4" hex head and insert the proper 1/4" driver. Adjust the

LagMaster pole tool to length.

Push the smooth rod between the pole and the wire bale on the LagMaster adjusting pin to keep the rod from whipping while

turning in the screw for safety.

Turn in the screw cautiously being careful not to over torque or strip the screw.

Remove the tool.

Secure the chain in the magazine so it does not whip when rotating the pole. Now rotate

the eye lag screw until it is seated.

Lower the LagMaster Plus™.

Adjust the pole to length and rotate the screw until it is seated. Pull down on the

pole so that the wire is caught on the ring.

Rotate the pole again to twist the wire. Pull the wire through the plug to complete the

installation.

Turn your pole tool into a very long screwdriver. This LagMaster Plus™ plug works with any 1/4" hex driver.

Install smooth rod with a Minerallac™ or Caddy™ spring clip assembly and screw. The Flash fastener is shown here.

Overhead screw applications: (1/4" hex plug)

Lagmaster Plus™ wire plug hangs 12 or 9 gauge wire. No need for ladders, scaffolding or scissor lifts.Pre-wrapped wire on eye lags require a special plug (pre-wrapped plug).

Use with Twister Pre-Tied Wire!

Hang Chain: Move ring into the down position with set screw

Hang Wire: Move ring into the up position with set screw

LAGMASTER PLUSLAGMASTER PLUS




Pullout Shear (Ultimate average lbs.) (Ultimate average lbs.) Gypsum Thickness Gypsum Thickness 3/8" 1/2" 5/8" 3/8" 1/2" 5/8"

E-Z Anchor Lite 25 30 40 80 90 120

E-Z Mini Anchor 30 40 50 90 110 140

E-Z Anchor 40 50 75 135 150 200

E-Z Toggle 70 85 150 200 230 300

Maximum Fixture Anchor Description Anchor Material Part Number Quantity Thickness E-Z Anchor Lite™ White Nylon 5006902 100 Count 3/4" E-Z Mini Anchor™ Zinc 5033902 100 Count 3/4" 5034902 50 #6 x 1 1/4" SMS 50 #8 x 1 1/4" SMS E-Z Anchor® Zinc 5000902 100 Count 3/4" White Nylon 5003902 100 Count E-Z Toggle™ Zinc 5014901 50 Count 5/8" 50 #8 x 2 1/8" Pan SMS 5017901 50 Count 50 #8 x 2 1/8" Pan Large Washer Face SMS

E-Z PRODUCTSSelf-Drilling Drywall AnchorsThe original! Fast and easy self-drilling anchors.

E-Z Anchor®, E-Z Anchor Plastic™, E-Z Mini Anchor®, E-Z Hanger®, E-Z Anchor Lite™, E-Z Toggle™, E-Z Anchor Plastic Plus™

Electrical FixturesThermostatsHVAC FixturesPlumbing FixturesBathroom AccessoriesShelving and SupportsMirrorsPicture FramesBracketsPlaques and AwardsCloset OrganizersCoat RacksCurtain Rods

SignsBulletin BoardsControl SystemsDecorative Wall HangingsOffice Material HoldersSmoke DetectorsClocksKitchen AccessoriesDoorbellsTelecommunications EquipmentChalk BoardsRemote Control Boxes

Product SpecificationsProduct Material:Zinc die cast NylonDrilling Capacity:3/8'', 1/2'' and 5/8'' gypsum wallboard

Applications

3/8" 1 5/16"

E-Z Anchor Lite

3/8" 1 1/4"

E-Z Mini Anchor

1/2" 1 5/8"

E-Z Anchor

9/16" 2 1/2"

E-Z Toggle

Selector Guide

Performance Data

Ligh

tD

uty

Med

ium

Dut

yH

eavy

Dut

y

1. Place #2 Phillips screwdriver into recess of E-Z Anchor Lite, E-Z Mini Anchor, E-Z Anchor or E- Z Anchor Plastic Plus.

2. Press into drywall while turning the anchor clockwise until it is seated flush with wall.

3. Place fixture in position over installed E-Z Anchor Lite, E-Z Mini Anchor, E-Z Anchor, or Plastic Plus. Insert screw with screw driver. Tighten fixture in place.

1. Place #2 Phillips screwdriver into recess of E-Z Toggle. Press into drywall while turning the anchor clockwise until it is seated flush with wall and arrows on head are parallel to stud.

2. Place fixture in position over installed E-Z Toggle. Insert screw and push through E-Z Toggle to engage clamp.

3. Continue turning screw until tight. The clamp will move back against the drywall as the screw turned.

Installation GuidelinesLight Duty & Medium Duty E-Z Anchors Heavy Duty E-Z Toggle

E-Z PRODUCTSE-Z PRODUCTS

111




E-Z PRODUCTSE-Z PRODUCTS




Bantam PIug™Base material - concrete, block, brick and wallboardAnchor Material - plastic

The Bantam Plug™ anchor is a plastic anchor designed for use with lightweight fixtures with a sheet metal or wood screw. The anchor is recommended for light duty static applications where holding power is not a critical factor. It should not be used overhead.

Kits - Slotted/Phillips Pan Head Sheet Metal Screws

100 anchors and screws plus one drill bit per kit

Cat. Drill Min. Std. Std. Mstr.No. Size Dia. Depth Box. Ctn. Ctn. 7559 6-8 x 3/4" 3/16" 3/4" 100 1000 50007569 8-10 x 7/8" 3/16" 7/8" 100 1000 50007579 10-12 x 1" 1/4" 1" 100 1000 50007589 14-16 x 1 1/2" 5/16" 1 1/2" 50 500 2500

Cat. Anchor Screw Min. Anchors Std.No. Kit No. Size Size Depth & Screws Ctn. 8934 8-8 8-10 8 x 1" 7/8" 100 10

8936 8-10 10-12 10 x 1" 1" 100 10

8938 8-12 10-12 12 x 1" 1" 100 10

LIGHT DUTY ANCHORSLIGHT DUTY ANCHORS

Cat. Tie Wire Drill Std. Std.No. Size Hole Size Dia. Box Ctn.4247 1/4" x 4" 7/32" 5/8" 100 100 4257 1/4" x 5" 7/32" 5/8" 100 100

Tie Wire Acoustical Toggle

Toggle Wings Only

Cat. Screw Drill Wall Std. Std.No. Size Length Dia. Thickness Box Ctn. 2100 1/8" XS 1 1/16" 5/16" 1/8"-1/4" 100 5002101 1/8" S 1 3/4" 5/16" 3/8"-1/2" 100 5002102 1/8" L 2 1/4" 5/16" 5/8"-1" 100 5002103 1/8" XL 2 11/16" 5/16" 1 1/4"-1 1/2" 50 2502111 3/16" S 2" 3/8" 3/8"-5/8" 50 2502112 3/16" L 2 1/2" 3/8" 3/4"-1 1/8" 50 2502113 3/16" XL 3" 3/8" 1 1/4"-1 3/4" 25 1252121 1/4" S 2 1/4" 7/16" 3/8"-1/2" 50 2502122 1/4" L 2 3/4" 7/16" 5/8"-1 1/8" 50 2502123 1/4" XL 3 3/8" 7/16" 1 1/4"-1 3/4" 25 125

Combination Slotted Phillips Head Polly™Base material - plaster, wallboard, block, hollow tile and plywoodAnchor material - carbon steel

The PoIIy™ is a sleeve type hollow wall anchor designed for use in base materials such as plaster, wallboard, concrete block, hollow tile or plywood.

Cat. Screw Wall Std. Std.No. Size Length Thickness Box Ctn.2180 1/8"x XS 1 3/8" 1/8"-1/4" 100 5002182 1/8" S 2" 3/8"-1/2" 100 5002184 1/8" L 2 3/8" 1/2"-3/4" 100 500

Drive Polly™

Cat. Std. Std.No. Description Box Ctn.2150 Polly™ Setting Tool 1 1

Polly™ Setting Tool (Fits All Sizes)

XS-Extra Short S-Short L-Long XL-Extra Long

XS-Extra Short S-Short L-Long XL-Extra Long

Cat Screw Drill Std. Std.No. Size Dia. Box Ctn.4000 1/8" 3/8" 100 500 4020 3/16" 1/2" 100 10004220 1/4" 5/8" 100 1000 4330 5/16" 7/8" 50 500 4430 3/8" 7/8" 50 500 4540 1/2" 1 1/4" 25 25

113




Base material - concrete, block, brick and stoneAnchor material - plastic

The Fluted Plastic Anchor is designed for light duty fastening applications with sheet metal or wood screws. Longitudinal ribs on the anchor body prevent it from turning during tightening of the screw. This inexpensive plastic screw anchor comes color-coded by diameter for easy application. The anchor is recommended for light duty static applications where holding power is not a critical factor. It should not be used overhead.

Cat. Screw Drill Std. Std. Mstr.No. Size Dia. Box Ctn. Ctn.9003 6 x 3/4" 5/32" 100 1000 50009005 6 x 1" 5/32" 100 1000 5000

9011* 8 x 3/4" 11/64" 100 1000 50009013 8 x 1" 11/64" 100 1000 50009015* 8 x 1 1/4" 11/64" 100 1000 50009017* 8 x 1 1/2" 11/64" 100 1000 5000

9024* 10 x 3/4" 3/16" 100 1000 50009026 10 x 1" 3/16" 100 1000 50009028 10 x 1 1/4" 3/16" 100 1000 50009030 10 x 1 1/2" 3/16" 100 1000 5000

9039 12 x 1" 1/4" 100 1000 50009041 12 x 1 1/4" 1/4" 100 1000 50009043 12 x 1 1/2" 1/4" 100 1000 50009045 12 x 2" 1/4 100 1000 5000

9050 14 x 1" 9/32" 100 1000 50009052 14 x 1 1/4" 9/32" 100 1000 50009054 14 x 1 1/2" 9/32" 100 1000 50009056 14 x 2" 9/32" 100 1000 5000

9063 16 x 1 1/2" 5/16" 50 500 2500

9072 20 x 1 1/2" 3/8" 50 500 25009074 20 x 2" 3/8" 50 500 2500

Fiberplug™

Cat. Drill Min. Std. Std.No. Size Dia. Depth Box Ctn9409 6-8 x 3/4" 1/4" 3/4" 100 10009414 6-8 x 1" 1/4" 1" 100 10009419 6-8 x 1 1/2" 1/4" 1 1/2" 100 10009429 10-14 x 1" 5/16" 1" 100 10009439 10-14 x 1 1/2" 5/16" 1 1/2" 100 10009460 16-18 x 1 1/2" 3/8" 1 1/2" 25 250

Cat Screw Drill Std. Std.No. Size Dia. Box Ctn.9080 3/8" x 2" 7/16" 25 2509082 3/8" x 2 1/2" 7/16" 25 2509084 3/8" x 3" 7/16" 25 250

Base material - concrete, block, brick, stone and plaster Anchor material - jute fiber with lead liner

The Fiberplug™ is a jute fiber screw style anchor (formerly known as the Rawl (plug) designed for use in concrete, block, brick, stone, and plaster. Designed for use with wood, sheet metal and lag screws.

Scru-Lead™Base material - concrete and blockAnchor material - lead alloy

The Scru-Lead™ anchor is designed for use with sheet metal or wood screws in concrete, block or brick. The anchor is made entirely of lead alloy which is soft enough for easy installation, yet hard enough to give sure, secure holding power. The performance of this product depends on the integrity of the base material. The anchor is recommended for light duty applications where holding power is not a critical factor. It should not be used overhead.

Lag Screw Sizes* Discontinued item once current stock is exhausted

LIGHT DUTY ANCHORSLIGHT DUTY ANCHORS

Cat. Drill Min. Std. Std.No. Size Color Dia. Depth Box Ctn.7500 4-6 x 1 White 3/16 1 100 10007505 7-9 x1 Red 7/32 1 100 10007510 10-12 x 1 Green 1/4 1 100 10007515 10-12 x 1 1/4 Green 1/4 1 1/4 100 10007520 10-12 x 1 1/2 Green 1/4 1 1/2 100 10007525 14 x 1 Blue 5/16 1 100 10007530 14 x 1 1/2 Blue 5/16 1 1/2 100 1000

Fluted Plastic Anchor




POWER FASTENERS DRYWALL ANCHORSPOWER FASTENERS DRYWALL ANCHORS

115








Cat. Wall Drill Std. Std.No. Size Thickness Dia. Box Ctn.2302 Mini 1/8" 5/16"' 100 10002303 Short 3/8" 5175" 100 1000 2304 Medium 1/2" 5/16" 100 1000 2305 Long 5/8" 5/16" 100 1000 2306 Extra Long 3/4" 5/16" 100 1000 2307 Super Long 1" 5/16" 100 1000

Poly Toggle™ Plastic Hollow Wall AnchorBase material - wallboard or solid masonryAnchor material - plastic

The Poly-Toggle® is a screw actuated hollow wall anchor for use in paneling, wallboard and solid masonry available in 6 sizes to match the most common wall thicknesses. In solid base materials, the anchor can be used by removing the outer wings. The performance of this product depends on the integrity of the base material in which it is installed. The anchor is recommended for light duty static application where holding power is not a critical factor.

Base material - gypsum wallboard, plaster, some hollow masonryAnchor material - plastic

Pop Toggle™ fasteners are hollow wall anchors ideal for static applications requiring light to medium load performance. Installation is very fast, needing a pre-drilled 5/16" diameter hole. The fastener pre-installs without a screw, allowing for easy placement and removal of the fixture. Pop Toggle™ fasteners are not recommended for use overhead or applications where holding values are critical.

Pop Toggle™ Cat. Std. Std.No. Description Box Ctn. 04060 Pop Toggle™ Small 100 1000 04062 Pop Toggle™ MedIum 100 1000 04064 Pop Toggle™Large 100 1000


117








ZIP-TOGGLEZIP-TOGGLE

119




Strap-ToggleTMProduct Description

Position the fixture. Insert the bolt though the fixture and tighten. The minimum bolt length should be at least 1/2 longer than the combined wall and fixture thickness.

The Strap-Toggle is a pre-assembled anchor consisting of a carbon steel wing and a locking cap/ratchet leg assembly molded from engineered plastic. It is available in both 3/16", 1/4", 3/8" and 1/2" sizes. When compared to traditional toggles, this unique anchor can be installed in a smaller hole and does not require a fixture or screw to set it. The anchor can be easily adjusted to accommodate a wall thickness of up to 2-1/2" while using a shorter bolt.

Installation is simple and four times faster than traditional toggles or metal hollow wall anchors. The specially designed locking cap and ratchet leg holds the wing snugly against the inside of a hollow wall. This prevents the anchor from spinning during installation of the bolt and allows for easy removal of the fixture for maintenance.

Installation of the anchor is easy. Simply drill a hole into the cavity of the hollow base material and insert the anchor. Then pull the ring and slide the cap along the straps until the flange of the cap is firmly set against the surface of the base material. Snap the straps off and the anchor is ready for use. It's that simple! The bolt and fixture may be installed and removed as often as necessary without affecting the anchor.

Installation Instructions

The following approvals and listings are for reference purposes. They should be reviewed by the design professional responsible for the product installation to verify approved sizes, base materials, and compliance with local codes.

Federal SpecificationThe Strap-Toggle meets the descriptive requirements of FF-B-588D, Type V for a captive toggle.

Anchors for hollow walls shall be a pre-assembled captive style toggles meeting the requirements of Federal Specification FF-B-588D, Type V The anchors shall have a carbon steel wing portion formed in a 'U' channel shape that is zinc plated according to ASTM Specification B633, SC 1, Type Ill. The anchor shall have a locking cap and ratchet leg assembly molded from engineered plastic. The assembly shall hold the wing snugly against the inside of the hollow wall prior to installation and after removal of the bolt. Strap Toggle anchors shall be as supplied by Powers Fasteners, Inc.

Drill the proper size hole into the cavity of the hollow base material.

Position the wing parallel to the plastic legs and slide the anchor through the drilled hole into the hollow cavity.

Pull the wing firmly against the inside wall of the hollow material using the ring, then slide the plastic cap forward until the flange is seated flush against the work surface.

Place your thumb between the plastic straps and snap the straps off.

SizesThe Strap-Toggle is a heavy duty hollow wall anchor designed for use in base materials such as plaster, wallboard, concrete block or hollow tile.

NOTE: The values listed above are ultimate load capabilities. These capabilities should be reduced by a minimum safety factor of 4 or greater to determine the allowable working load. Refer to the Fastening Systems Design Manual published by Powers Fasteners, Inc. for complete details. Since the consistency of gypsum wallboard and hollow block varies greatly these load capacities listed should be used as guidelines only job site tests should be conducted to determine the actual load capabilities.

The following ultimate load capabilities are based on testing according to ASTM E 488.

Anchor SizesCat. No.

Size Drill Diameter

Wall Thickness

Std. Box

Std. Ctn.

Wt./100

4052 3/16" x 4" 1/2" 2 1/2" 50 300 3 1/2

4054 1/4" x 4" 1/2" 2 1/2" 50 300 3 1/2

4056 3/8" x 4" 3/4" 2 1/2" 25 150 5

4058 1/2" x 4" 3/4" 2 1/2" 25 150 5

* 9/16" Bit may be required for very dense materials.

Installation SpecificationsAnchor Size 3/16" 1/4" 3/8" 1/2"

ANSI Drill Bit Size* 1/2" 1/2" 3/4" 3/4"

Cap Size 5/8" 5/8" 1" 1"

Grip Range 2 1/2" 2 1/2" 2 1/2" 2 1/2"

Thread Size 3/16"-24 1/4"-20 3/8"-16 1/2"-13

Max. Torque (ft.-lbs.) 5 5 5 5

Minimum Clearance 1 7/8" 1 7/8" 1 7/8" 1 7/8"Material Specifications

Anchor Component Component Material

Wing AiSi CIOIO

Zinc Plating ASTM B633, Sd, Type iii, (Fe/zn 5)

Cap / Strap Engineered Plastic

Performance Data

Ultimate Load Capacities For Gypsum Wallbaord

Size Drill Dia.Wallboard Thickness

3/8" 1/2" 5/8" 3/4"Tension (lbs.) 3/6"

1/4"3/8"1/2"

1/2"1/2"3/4"3/4"

120130135140

130145150150

195210220220

205215230230

Shear (lbs.) 3/16"1/4"3/8"1/2"

1/2"1/2"3/4"3/4"

240270275290

285295300355

380420420430

440470475485

Ultimate Load Capacities For C-90 Hollow Back

Size Drill Dia.ASTM C-90

Hollow Back Tension (Lbs.)

Shear (Lbs.)

3/16"1/4"3/8"1/2"

1/2"1/2"3/4"3/4"

1,0801,3551,4351,720

7401,4202,3302,980

POWER FASTENERS STRAP TOGGLEPOWER FASTENERS STRAP TOGGLE




GYP-FAST GAS TOOLS AND FASTENERSGYP-FAST GAS TOOLS AND FASTENERS

121




GYP-FAST GAS TOOLS AND FASTENERSGYP-FAST GAS TOOLS AND FASTENERS




GYP-FAST AIR TOOLS AND FASTENERSGYP-FAST AIR TOOLS AND FASTENERS

123




GYP-FAST AIR TOOLS AND FASTENERSGYP-FAST AIR TOOLS AND FASTENERS




Rod hanging made fast and secure!

SAMMY SUPER SCREWSSAMMY SUPER SCREWS

125125




Description Colors1 5/8" ga. 10’ half slot aluminum, green, pre-galv.

Channel FrameModel No. a12h

Description Colors1 5/8" ga 10’ full slot aluminum, green, pre-galv

Channel FrameModel No. a12s

Description Model NumberChannel beam clamp bc19

Channel FrameModel No. bc19

Description Sizes2 hole pipe strap 1/2", 3/4" 1", 1 1/4", 1 1/2" 2" 2 1/2", 3", 3 1/2", 4", 5", 6"

Channel FrameModel No. 2str

Description Model NumberChannel beam clamp assembly bc17afor a,b,c & m channel

Channel beam clamp assembly bc17dfor d & e channel

Plate only for bc17 beam clamp bc17pl

Channel FrameModel No. bc17a, bc17d, bc17

Description SizeChannel I-beam clamp 3/8", 1/2"


Description Model NumberBeam clip bc200000eg


STRUT / FRAMING PRODUCTSSTRUT / FRAMING PRODUCTS

ERISTRUT®

126126




Description Model NumberZ beam clip bc21

Channel FrameModel No. BC21

Description Model NumberUniversal beam clamp 1/4" bc26


Description Model NumberSpreader caps for A channel bc23a000egSpreader caps for C channel bc23c000eg

Channel FrameModel Nos. BC23A, BC23C

· More versatile alternative to window bracket or standard beam clamp.

· Strut to beam flanges up to 3/4" thickness for 1 5/8" deep strut.

· Fits C purlin with 3/4" lip height (max) when used with 1-5/8" deep strut.

· Lock nut and hardened cup point setscrew provide secure grip on tapered sections.

· Corrosive resistant galvanized finish.

· Available in hot dipped galvanized finish. (Special order).

· Permits strut channel opening positioning in any direction.

· For flange sizes up to 1 when used as a beam clamp.

Description Part NumberChannel beam clamp for a, b, c & m 4-6 bc700406egChannel beam clamp for a, b, c & m 6-9 bc700609egChannel beam clamp for a, b, c & m 9-12 bc700912egChannel beam clamp for a, b, c & m 12-15 bc701215eg


STRUT CLAMPS

Note: When used as a strut hanger the minimum required is two

BEAM CLAMPS

Up to 1" flange

3/4 to 1 5/8" flange

ERISTRUT®STRUT / FRAMING PRODUCTSSTRUT / FRAMING PRODUCTS

127127




1/2" - 4" size

1/4", 3/8", 5“and 6" size

Channel FrameModel No. OD

Large sizes available upon request.

Description SizesOD pipe clamp 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1for tubing 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1 3/4", 1 7/8, 2", 2 1/8", 2 1/4", 2 3/8", 2 1/2", 2 5/8", 2 3/4", 2 7/8", 3, 3 1/8", 3 1/4", 3 3/8", 3 1/2", 3 5/8", 3 3/4", 3 7/8", 4", 4 1/8", 4 1/4", 4 3/8", 4 1/2", 4 5/8", 4 3/4", 4 7/8", 5", 5 1/8", 5 1/4", 5 3/8", 5 1/2", 5 5/8", 5 3/4" 5 7/8", 6", 6 1/8", 6 1/4" 6 3/8", 6 1/2", 6 5/8", 6 3/4", 6 7/8", 7", 7 1/8", 7 1/4", 7 3/8, 7 1/2", 7 5/8", 7 3/4", 7 7/8", 8", 8 1/8", 8 1/4", 8 3/8", 8 1/2", 8 5/8", 8 3/4", 9 1/8", 9 5/8", 9 3/4"

Watch for one piece design with retained bolt.

Description SizesCopper tubing 1/4 (3/8 od), 3/8 (1/2 od),pipe clamp 1/2 (5/8 od), 5/8 (3/4 od), 3/4 (7/8 od), 1 (1 1/8 od), 1 1/4 (1 3/8 od), 1 1/2 (1 5/8 od), 2 (2 1/8 od), 2 1/2 (2 5/8 od), 3 (3 1/8 od), 3 1/2 (3 5/8 od), 4 (4 1/8 od), 5 (5 1/8 od), 6 (6 1/8 od)

Channel FrameModel No. COPC

Description SizesPipe clamp for E.M.T. 3/8", 1/2", 3/4", 1", 1 1/4", 1 1/2", 2

Channel FrameModel No. EMTC

Description Colors13/16" ga 10’ half slot aluminum, green, pre-galv.

Channel FrameModel No. C12H

Description Sizes1 hole E.M.T. strap 1/2", 3/4", 1", 1 1/4", 1 1/2", 2"

Channel FrameModel No. EPS

Description Size2 hole splice plate 3 1/2

Channel FrameModel No. F09

Description Model NumberSquare channel washer 1/4" - 5/16" f130000egNote: 1/4" applications require additional 1/4" washerSquare channel washer 3/8" f140000egSquare channel washer 1/2" f150000egSquare channel washer 5/8" f160000egSquare channel washer 3/4" f170000egSquare channel washer 7/8" f180000eg

Channel FrameModel Nos. F13, F14, F15,

F16, F17, F18

Description Model Number2 hole corner angle (1 5/8 x 2 1/4) l100000eg

Channel FrameModel No. L10

Description Model Number3 hole corner angle 2 1/4" x 3 1/2" l180000eg3 hole corner angle 1 7/8" x 3 7/8" l190000eg3 hole corner angle 1 5/8" x 4 1/2" l290000eg

Channel FrameModel Nos. L18, L19, L20


128128




Description SizesStrut nut w/o spring #8*, #10*, 1/4"*, 5/16"*, 3/8"*, 1/2"†, 5/8"†, 3/4"†, 7/8"†

*for all channel † for a,b,d,e, & m channel

Channel NutsModel No. nut

Description SizesStrut nut w/o spring for c channel 1/2", 5/8", 3/4", 7/8"

Channel NutsModel No. nutc

Channel FrameModel No. rigd

1/2 - 4“ size

3/8", 5“-12" size

Watch for one piece design with retained bolt. Also available in stainless.

Description SizesPipe clamp for rigid pipe 3/8", 1/2", 1/2" yellow chromate, 3/4", 3/4" yellow chromate, 1", 1" yellow chromate, 1 1/4", 1 1/4" yellow chromate, 1 1/2", 1 1/2" yellow chromate, 2", 2" yellow chromate, 2 1/2", 2 1/2" yellow chromate, 3", 3" yellow chromate, 3 1/2", 3 1/2" yellow chromate, 4", 4" yellow chromate, 5", 6", 8", 10", 12"

Description SizesPipe cushion clamp 1/4", 3/8", 1/2", 3/4", 1", 1 1/4", 1 1/2", 2", 2 1/2", 3", 3 1/2", 4"

Channel FrameModel No. pcc

Description Part NumberPost base for a channel p090000eg

Channel FrameModel No. p09

Description Part NumberPost base for a channel p110000eg

Channel FrameModel No. p11

Description Size2 hole corner angle 1 7/8 x 2

Channel FrameModel No. l11

Description Part Number4 hole corner angle l220000eg


Description Angle °2 hole 7 1/2˚, 30˚, 45˚, 60


Description Angle °2 hole 30˚, 45˚, 60˚, 82 1/2˚



129129




Description SizesTop spring nut for all channel 1/4, 3/8Top spring nut 1/2 For A, B, D and M channel

Channel FrameModel No. tsnt

Description SizeTop spring nut for all channel 1/2

Channel FrameModel No. tsnc

Description SizesTube cushion 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1" c lamp 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1 3/4", 1 7/8", 2", 2 1/8",2 3/8", 2 5/8", 3 1/8", 3 5/8", 4 1/8"

Channel FrameModel No. tcc

Watch for one piece design with retained bolt.

Description SizesUniversal pipe clamp 1/2", 3/4", 1", 1 1/4", 1 1/2", 2

Channel FrameModel No. univ

Description Sizes1 hole pipe strap 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1"

Channel FrameModel No. strDescription Sizes

Spring nut for a&b channel #8, #10, 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8"

Channel NutsModel No. spra

Description SizesStud spring nut 1/4" 7/8", 1 1/8", 1 1/2", 1 5/8", 1 7/8", 2 1/8"

Stud spring nut 3/8" 7/8", 1 1/8", 1 5/8", 1 7/8", 2 1/8"

Stud spring nut 1/2" 1 1/8", 1 5/8", 1 7/8"

Stud spring nut 5/8" 7/8", 1 1/8", 1 7/8", 2 1/8

Channel NutsModel No. sprm

Description SizesSpring nut for c channel #8, 1/4", 5/16", 3/8", 1/2" ,5/8", 3/4

Channel NutsModel No. sprc

Description SizesSpring nut for d & e channel #8, 1/4", 5/16", 3/8", 1/2", 5/8", 3/4"

Channel NutsModel No. sprd

Description SizesSquare nut 1/4", 5/16", 3/8", 1/2", 5/8"

Channel FrameModel No. sqnt


130130




• Easy installation to beam flanges up to 1/2".• Supports 1/4" and 3/8" threaded rod, S-hooks, electrical boxes, conduit and bridle rings.• Accommodates standard 1/4"-20 or #10-24threaded bridle rings.Note: When using rigid conduit on P Series, use next size larger clip (1/2" rigid use 12P).

• Simple solution for supporting of air duct.• Accepts wider strap widths up to 1 1/4".• The new clips are made from galvanized steel instead of

spring steel. This expands the use to more applications, especially when used with other plated parts like our BC2OO beam clamp.

Note: Loads indicated are for CADDY® fasteners only.

Catalog Fig. Flange Load Qty. PerNumber No. Thickness Rating BoxMSS24 1 1/8" to 1/4" 200# 50MSS58 1 5/16" to 1/2" 200# 50MSS912 1 9/16" to 3/4" 200# 50MSR24 2 1/8" to 1/4" 200# 50MSR58 2 5/16" to 1/2" 200# 50MSR912 2 9/16" to 3/4" 200# 50MSSBC200 3 1/8" to 5/8" 100# 50MSRBC200 4 1/8" to 5/8" 100# 50MSSCPNA 5 Strap hanger 160# 50 to angle bracket.

Strap Hanger Clips

Beam Clamp

Improved galvanized and plated components for more demanding environments.

Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5

• Easily attaches 4" and 4 11/16" outlet boxes to metal stud.

• Support leg eliminates movement of box in wall.

• Can be attached to metal or wood stud.• Offset to eliminate dry wall bulges.• Delivers compliance with:

NEC Article 300-4(d) when used for 4" and 4 11/16" outlet boxes to metal or wood studs.CEC Rule 12-3012 for 4" and 4 11/16" outlet boxes to metal or wood studs.

Catalog Fig. Box Stud Qty. Number No. Application Size(s) Depth Per Box H23 1 U.S. 4" sq. & 4 11/16" 2 1/2" & 3 1/2" 100

H2STC 1 Canada 4" sq. & 4 11/16" 2 1/2" & 3 1/2" 100

H4 1 U.S. 4" sq. & 4 11/16" 4" 50

H6 1 U.S. 4" sq. & 4 11/16" 6" 50

H46TC 1 Canada 4" sq. & 4 11/16" 4" & 6" 100

HS3 2 U.S. & Canada Switch 2 1/2" & 3 1/2" 100

Mounting Bracket For Any Electric BoxFig. 1

Fig. 2

CADDY BEAM CLIPSCADDY BEAM CLIPS

131131




Size range: 3/8" through 7/8" rod sizes.

Material: Malleable iron casting with a hardened cup point set screw and lock nut.

Finish: Black. Ordering: Specify rod size, finish and model number.

Approvals: UL Listed for top or bottom of Beam. FM Approved for NFPA 13, maximum rated pipe size. Complies with Manufacturers Standardization Society SP-69 (Type 19 & 23).

Function: Recommended for attaching hanger rod to top or bottom flange of a beam or bar joist, where the thickness of a joist or flange does not exceed 3/4". The open back design permits rod adjustment.

Installation: Must install in an upright position. Also available in: Electro-Plated Zinc and 304 Stainless Steel.

Appx. Wt. MaximumModel Per 100 Recommended CartonNumber Photo Reference (pcs.) Load (lbs.) Quantity A B C D E F G 103 - 101 3/8" 1" 1 1/2" 1/2" 1" 3/4" 7/8" 33 400 100104 - 101 1/2" 1 1 1/2" 1/2" 1" 3/4" 7/8" 33 500 100105 - 101 5/8" 1 1/2" 1 1/2" 1/2 1" 3/4" 1" 22 600 50106 - 101 3/4" 1 7/8" 1 3/4" 5/8" 1 3/8" 1" 1 1/4" 88 800 50107 - 101 7/8" 2" 1 3/4" 5/8 1 1/2" 1" 1 1/4" 79 1200 25

Universal Beam Clamp


Material: Malleable iron casting with a hardened cup point set screw and lock nut.

Finish: Black. Ordering: Specific rod size, finish and model number.

Approvals: UL Listed for top or bottom of Beam. FM Approved for NFPA 13, maximum rated pipe size. Complies with Manufacturers Standardization Society SP-69 (Type 19 & 23).

Function: Recommended for attaching hanger rod to top or bottom flange of a beam or bar joist construction. The open back design permits rod adjustment.

Installation: Must install in an upright position. Also available in: Electro-plated zinc.

Appx. Wt. MaximumModel Per 100 Recommended CartonNumber Photo Reference (pcs.) Load (lbs.) Quantity A B C D E F G 113-101 3/8" 1-5/8" 2" 3/4" 1" 1 1/4" 7/8" 28 400 50114-101 1/2" 1-5/8" 2" 3/4" 1" 1 1/4" 7/8" 34 500 50115 - 101 5/8" 1 3/4" 2 1/4" 3/4" 1 1/4" 1 1/4" 1" 66 600 50116 - 101 3/4" 1 7/8" 2 3/8" 3/4" 1 3/8" 1 1/4" 1 1/4" 83 800 50

Wide Throat Beam Clamp


Material: Carbon steel with a hardened cup point set screw and available with or without a lock nut.

Finish: Black. Ordering: Specify rod size; finish; and model number.

Approvals: UL Listing and FM Approved for NFPA 13, maximum rated pipe size. Complies with Federal Specification WW-H 171 E (Type23) and Manufacturers Standardization Society SP-69 (Type 23).

Function: Designed for structural attachment of hanger rod to bottom flange of a metal beam, purlins, channel or angle iron. The hanger rod should make contact with the beam flange to ensure full engagement.

Also available in: Electro plated zinc and 304 stainless steel. Maximum pipe size: 4".

Maximum Appx. Wt. Model Recommended Per 100 CartonNumber Photo Reference Load (lbs.) (pcs.) Quantity A B C D E

203 - 100 3/8" 3/8" 2 3/8" 2 5/16" 13/16" 400 41 100203 - 101 w/locknut 3/8" 3/8" 2 3/8" 2 5/16" 13/16" 400 45 100204 - 100 1/2" 1/2" 2 3/8" 2 5/16" 13/16" 500 43 100204 - 101 w/locknut 1/2" 1/2" 2 3/8" 2 5/16" 13/16" 500 46 100205 - 100 5/8" 5/8" 2 3/8" 2 1/4" 13/16" 550 58 50205 - 101 w/locknut 5/8" 5/8" 2 3/8" 2 1/4" 13/16" 550 66 50206 - 100 3/4" 3/4" 2 3/8" 2 1/4" 13/16" 600 80 50206 - 101 w/locknut 3/4" 3/4" 2 3/8" 2 1/4" 13/16" 600 86 50207 - 100 7/8" 3/4" 3" 3 1/4" 13/16" 900 168 25207 - 101 w/locknut 7/8" 3/4" 3" 3 1/4" 13/16" 900 176 25

SteelC-Clamp

GLOBE PIPE HANGER PRODUCTSGLOBE PIPE HANGER PRODUCTSGLOBE

132132




Catalog Conduit Box Patent number Size Qty. Number BG-6 3/8" 100 4958792 BG-8-12 1/2", 3/4" 100 BG-16 1" 100 BG-20 1 1/4" 100 BG-24 1 1/2" 100 BG-32 2" 100

BG-6-4T 3/8" 100 4958792 BG-8-1 2-4T 1/2", 3/4" 100 BG-16-4T 1" 100 BG-20-4T 1 1/4" 100 BG-24-4T 1 1/2" 100 BG-32-4T 2" 100

Catalog Stud Box Box number spacing Depth Qty. BB2-16 16" 1 1/2" 50

BB2-24 24" 1 1/2" 50

Catalog Metal Box Patent number stud size Qty. No. BB4-23 21/2", 31/2" 100 #4757908

BB4-4 4" 100 #4757908

BB4-6 6" 25 #4757908

BB4-XT6 Extends BB3,BB4-23, 100 #4757908 & BB4-4 for use on 6" Deep Studs

Read safety/installation instruction sheets in packages before use. These products are designed for positioning only. No load rating.

Box Support Brackets

• Supports either 4" square or 411/16" boxes• Available for 2 1/2", 3 1/2", 4" and 6" metal studs.• Attaches with screws to either side of metal stud.• Brackets may be piggy-backed in series on same side of metal stud.• Finish: Pre-galvanized


Box Mounting Brackets

• Supports boxes located between studs 16" or 24" on center.• Adjustable design fits both 1 1/2" and 2 1/8" deep boxes• Boxes attach early with sheet metal screws through pre-punched holes• Bar is marked in 1/2" increments.• Accommodates 4" thru 24" stud spacing using BB2-ac adapters.• Finish: Pre-galvanized

Read safety/installation instruction sheets in packages before use.

Conduit Fasteners

• Supports3/8" to 2" conduit.• Unique Guide-Rite® Fastener provides for fast and easy installation with pliers.• Available with clearance hole for 1/4" bolt or 1/4" -20 thread impression mounting hole.• Static Load Capacity: 100 Lbs. - Vertical, 25 Lbs. - Horizontal

Guide-Rite® Fastener With clearance Hole For 1/4" Bolt

Guide-Rite® Fastener With 1/4" 20 Thread Impression 25 lbs

100 lbs

Static Load

Capacity

BOX AND CONDUIT FASTENERSBOX AND CONDUIT FASTENERS

133133




Catalog Box number Description Qty. BA12 Box Hanger 24" Span 50 BB27 Box Mounting 100 Clip (with Screw)

Catalog Box Number Qty. BW-8 100 BW-12 100 BW-16 100 BW-20 100

Conduit #10 &#12 #8 & 9 3/16" & 1/8" to 5/16" to 7/16" to Size Wire Wire 1/4" Rod 1/4" Flange 3/8" Flange 1/2" Flange 1/2" EMT BW-8 BW-8 BW-8 BW-8 BW-12 BW-12

1/2" RIGID BW-8 BW-12 BW-12 BW-12 BW-12 BW-16

3/4" EMT BW-12 BW-12 BW-12 BW-12 BW-16 BW-16

3/4" RIGID BW-12 BW-12 BW-16 BW-16 BW-20* BW-20*

1" EMT --- BW-16 BW-16 BW-16 BW-20* BW-20*

1" RIGID --- --- --- BW-20* BW-20* BW-20*

1 1/4" EMT --- BW-20 BW-20 BW-20 ---

Catalog Box Number Description Qty. Bw4 Multi-size Wire Fastener 100

Cable Size #12 Wire #10 Wire #8 & 9 Wire 14-2 Cable BW4 BW4 BW4 14-3 Cable BW4 BW4 BW4 12-2 Cable BW4 BW4 BW4 12-3 Cable BW4 BW-8 BW-8

Catalog Wire Flange Box number Size Thickness Qty. BW2 #12 wire thru 1/8" - 3/8" 100 1/4" plain rod


Rod and Wire Fasteners

Rod and Wire Fasteners

• BW2 supports #10-24 or 1/4"-20 threaded bridle rings and provides easy attachment of electrical boxes• BW4 supports cables from #12 thru #8 wire in vertical or horizontal applications.

Note: An independent means of support is required.

• Attaches conduit to rods or flanges• Can be used for flexible metallic tubing, armored cable, portable cable, control cable, and communication cable.

*Note: For horizontal applications only.

Static Load

Capacity

25 lbs.50 lbs.

100 lbs.

Vertical Flange

Vertical Wireor Rod

Horizontal Flange

Electrical Box T-Bar Fasteners

• Supports 4" octagonal or square boxes• Allows for flush mounting or 3/4" offset for plaster ring.• One BB27 box mounting clip with screw is included with each hanger.• For additional support attach drop wire to BB27 Box Mounting tip.• Warning: Do not use for hanging acoustical tee.

BA12

BA27Box mounting clip (with screw)

ROD AND WIRE FASTENERSROD AND WIRE FASTENERS

134134




Part Flange Box Number Thickness Qty. BU-2-4 1/8" to 1/4" 100 BU-5-8 5/16" to 1/2" 100 BU-9-12 9/16" to 3/4" 100 BU-2-4-S 1/8" to 1/4" 100 BU-5-8-S 5/16" to 1/2" 100 BU-9-12-S 9/16" to 3/4" 100

Part Flange Static Box Number Thickness Load Cap. Qty. BE-I -2 3/32" To 9/64" 160 Lbs. 100 BE-2-4 1/8" to 1/4" 200 Lbs. 100 BE-5-8 5/16" to 1/2" 200 Lbs. 100 BE-9-12 9/16" to 3/4" 200 Lbs. 100

Catalog Stud Static Box Number Finish Length Load Cap. Qty. BA-4-16-W White 5/8" 50lbs. 100

BA-4-WN Black 100lbs. 100


Twist Fasteners

• Supports electrical fixtures rom 15/16" T-Bar.• 1/4"-20 stud available in varying lengths• BA-4-WN wing nut with 1/4" -20 thread impression included.• No special tools required.• Without nut add - LN, • Without stud add - LS

BA-4-16-W

BA-4-WN


Flange Beam Fasteners

• Permits fast and easy installation on bulb tees and bar joists• Clearance hole for 1/4" bolt in tab.• Simply installed with a hammer.


Universal Beam Fasteners

BU-2-4

BU-2-4Swith staked stud

• Suspend boxes or fixtures from beam flanges 1/8" to 3/4" thick.• Provided with 1/4"-20 thread impression for quick and secure attachment.• Simply installed with a hammer.• Available with staked stud (1/4" - 20 x 3/8")

Static Load CapacityNote: Indicated loads are static load capacity and should not be combined.

75 lbs. 100 lbs.

BEAM FASTENERSBEAM FASTENERS

135135




Part Flange Static Load Box Number Thickness Cap Qty. BC-1 Thru 1/2" 100 lbs. 100

Part Conduit Flange Box Number Size Thickness Qty. BG-6-U-2-4 3/8" 1/8" to 1/4" 100 BG-6-U-5-8 3/8" 5/16" to 1/2" 100 BG-6-U-9-12 3/8" 9/16" to 3/4" 100 BG-8-12-U-2-4 1/2", 3/4" 1/8" to 1/4" 100 BG-8-12-U-5-8 1/2", 3/4" 5/16" to 1/2" 100 BG-8-12-U-9-12 1/2", 3/4" 9/16" to 3/4" 100 BG-16-U-2-4 1" 1/8" to 1/4" 100 BG-16-U-5-8 1" 5/16" to 1/2" 100 BG-16-U-9-12 1" 9/16" to 3/4" 50

Part Conduit Flange Box Number Size Thickness Qty. BG-6-E-2-4 3/8" 1/8" to 1/4" 100 BG-6-E-5-8 3/8" 5/16" to 1/2" 100 BG-6-E-9-12 3/8" 9/16" to 3/4" 100 BG-8-12-E-2-4 1/2", 3/4" 1/8" to 1/4" 100 BG-8-12-E-5-8 1/2", 3/4" 5/16" to 1/2" 100 BG-8-12-E-9-12 1/2", 3/4" 9/16" to 3/4" 100 BG-16-E-2-4 1" 1/8" to 1/4" 100 BG-16-E-5-8 1" 5/16" to 1/2" 100 BG-16-E-9-12 1" 9/16" to 3/4" 50


Conduit To Beam Fasteners

• Supports 3/8" to 2" conduit.• Unique Guide-Rite® Fastener provides for fast and easy installation.• Fasteners will rotate 3600.• Simply installed with a hammer and pliers

Read safety/installation instruction sheets in packages before use.• Supports 3/8" to 2" conduit.• Unique Guide-Rite® Fastener provides for fast and easy installation.• Fasteners will rotate 3600.• Simply installed with a hammer and pliers

Static Load Capacity

BC1

75 lbs.


• Fits beam flanges thru 1/2" thick.• Accepts" S' hooks, 1/4" and 3/8" threaded rod, 1/4" -20 or #10-24 threaded bridle rings• Supports conduit and electrical boxes

Static Load Capacity

25 lbs.

CONDUIT AND BEAM FASTENERSCONDUIT AND BEAM FASTENERS

136136




Part Ring Thread Box Number Size Size Qty. BR-8-T 1/2" #10-24 100 BR-12-T 3/4" #10-24 100 BR-20-T 1 1/4" #10-24 100 BR-32-T 2" #10-24 100 BR-20-4T 1 1/4" 1/4"-20 100 BR-32-4T 2" 1/4"-20 100 BR-64-4T 4" 1/4"-20 50

BR-16-3W 1" 3/16" 100 BR-24-4W 1 1/2" 1/4" 100

BR-8 1/2" #10-24 100 BR-12 3/4" #10-24 100 BR-20 1 1/4" #10-24 100 BR-32 2" #10-24 100

Part Flange Box Number Description Thickness Qty. BH-2-4 Parallel 1/8" to 1/4" 100 BH-5-8 Parallel 5/16" to 1/2" 100 BH-2-4-R Right Angle 1/8" to 1/4" 100 BH-5-8-R Right Angle 5/16" to 1/2" 100


Strap Hangers

• Suspend straps thru 1" wide from beam flanges 1/8" to 3/4" thick.• Suspend from straps parallel or at right angles to beams• Simply installed with a hammer.• Static Load Capacity: 200 Lbs.

Parallel

Right Angle


Threaded Bridle Rings

• Supports low voltage communication cables from beams or rods when used with other fasteners• Ultimate Static Load Capacity: 50 Lb&• Finish: Zinc Rated

Threaded

Lag Screw For Wood

Beams

Unthreaded

STRAP HANGERS AND BRIDLE RINGSSTRAP HANGERS AND BRIDLE RINGS

137137




approx. Wt dimensions per 100 pipe size d c l t (low carbon) 1/2" 1/4" 1 5/16 3 1/4 2 3/8 7.4 3/4" 1/4" 1 1/8 3 5/16 2 3/8 7.7 1" 1/4" 1 3/8 3 7/16 2 3/8 8.1 1/3" 3/8" 1 5/16 3 1/4 2 3/8 19.0 3/4" 3/8" 1 1/8 3 5/16 2 3/8 19.7 1" 3/8" 1 3/8 3 7/16 2 3/8 21.0 1 1/4" 3/8" 1 11/16 3 3/4 2 3/8 22.5 1 1/2" 3/8" 2 4 2 1/2 24.3 2" 3/8" 2 7/16 4 1/2 2 1/2 27.3 2 1/2" 1/2" 2 15/16 5 1/4 3 57.3 3" 1/2" 3 9/16 5 13/16 3 63.5 3 1/2" 1/2" 4 1/16 6 5/16 3 69.4 4" 1/2" 4 9/16 6 13/16 3 74.9 5" 1/2" 5 5/8 7 13/16 3 86.7 6" 5/8" 6 3/4 9 1/2 3 3/4 162.0 8" 5/8" 8 3/4 11 1/2 3 3/4 200.4 10" 3/4" 10 7/8 13 13/16 4 364.6 12" 7/8" 12 7/8 16 1/16 4 1/4 561.7 14" 7/8" 14 1/8 17 5/16 4 1/4 618.8 16" 7/8" 16 1/8 19 5/16 4 1/4 676.6 18" 1" 18 1/8 21 11/16 4 3/4 1040.0 20" 1" 20 1/8 23 11/16 4 3/4 1130.0 24" 1" 24 1/8 27 11/16 4 3/4 1330.0 30" 1" 30 1/8 33 11/16 4 3/4 1620.0 36" 1" 36 1/8 39 11/16 4 3/4 1900.0

Finishes: plain, zinc, and hot-dip galvanized

Stainless steel available upon request

*hdg u-bolts furnished with 2 nuts assembled

Other standard and special u-bolts available upon request.

Size Approx. Approx. pcs. Wt. Per 100’ per drum 3/8x6x1x1 1/2 18 4500 8 22 3150 10 26 2500 12 30 1675 1/2x6x1x2 32 3200 8 41 2500 10 49 1600 12 58 1400 14 67 1200 16 75 1100 18 84 1000 5/8x6x2x4 56 1750 8 69 1500 10 83 1200 12 96 900 14 110 700 16 124 600 18 138 500

3/4x8x3x4 114 950 10 135 700 12 156 500 14 177 450 15 187 400 16 197 350 18 218 250 20 237 250 24 281 225 30 344 200 7/8x12x3x6 206 500 14 233 400 15 247 375 16 261 350 18 288 300 20 316 175 24 371 150 30 453 125 1x12x3x6 281 350 14 318 300 15 337 275 16 356 250 18 393 225 20 431 200 24 506 150 30 618 125 36 731 100

National coarse (USS) Size Wt Per 100’ Pcs per bundle 1/4-20 11.9 50 5/16-18 19.3 35 3/8-16 28.4 25 7/16-14 39.6 17 1/2-13 51.2 12 9/16-12 67.0 10 5/8-11 83.1 8 3/4-10 121.7 5 7/8-9 167.5 4 1-8 219.0 2 1 1/8-7 280.5 1 1 1/4-7 350.0 1 1 3/8-6 417.2 1 1 1/2-6 504.7 1 1 3/4-5 690.0 1 2-4 1/2 904.0 1 2 1/4 –4 1/2 1180.0 1 2 1/2-4 1460.0 1

Finishes: plain oil or zincStock lengths:Right hand threads-2', 3' 6', 10', 12'Left hand threads-3', 6', 12'

Threaded Rod - Carbon SteelThreaded rod - carbon steel

Stock anchor Bolts-bulk

Type 137 StandardPipe Size U-Bolts

Plain and hot galvanized*

Zinc and stainless available upon request

(DxLxCxT)

VULCAN

VULCAN THREADED ROD PRODUCTSVULCAN THREADED ROD PRODUCTS

We stock a full line of rod coupling nuts.

Page 199

138138




TAPCON® MASONRY ANCHORSTAPCON® MASONRY ANCHORS

Approved for use in ACQ Treated Lumber

Select a length that meets your application needs.

SELECTION CHARTTapcon® Stainless Steel Anchors

PART NO. 3/16”

HEX HEAD

PART NO. 1/4”

FLAT HEAD

RECOMMENDEDTAPCON LENGTH

In. (mm)

FIXTURETHICKNESS

INCHES

BITLENGTHIn. (mm)

DRILL BITPART NO.

SHW4-114 SPF4-114 1-1/4 (31.8) 0” - 1/4” 3-1/2 (88.9) 7901014

SHW4-134 SPF4-134 1-3/4 (44.5) 1/4” - 3/4” 3-1/2 (88.9) 7901014

SHW4-214 SPF4-214 2-1/4 (57.2) 3/4” - 1-1/4” 4-1/2 (114.3) 7901018

SHW4-234 SPF4-234 2-3/4 (69.9) 1-1/4” - 1-3/4” 4-1/2 (114.3) 7901018

SHW4-314 SPF4-314 3-1/4 (82.6) 1-3/4” - 2-1/4” 5-1/2 (139.7) 7901022

SHW4-334 SPF4-334 3-3/4 (95.3) 2-1/4” - 2-3/4” 5-1/2 (139.7) 7901022

SELECTION CHARTTapcon® SDS Bits

PART NUMBER DESCRIPTION

790059 7” (SDS Rotohammer Bits for use with 3/16”Tapcon)



SELECTION CHART

Tapcon® Anchors

PART NO. 3/16”

HEX HEAD

PART NO. 1/4”

HEX HEAD

PART NO. 3/16”

FLAT HEAD

PART NO. 1/4”

FLAT HEAD

RECOMMENDEDTAPCON LENGTH

In. (mm)

FIXTURETHICKNESS

INCHES

BITLENGTHIn. (mm)

BITS FOR3/16” TAPCON

PART NO.

BITS FOR1/4” TAPCON

PART NO.

BITS FOR3/16” SDSBIT NO.

BITS FOR1/4” SDSBIT NO.

HW3-114 HW4-114 PF3-114 PF4-114 1-1/4 (31.8) 0” - 1/4” 3-1/2 (88.9) 7900814 7901014 ---- ----

HW3-134 HW4-134 PF3-134 PF4-134 1-3/4 (44.5) 1/4” - 3/4” 3-1/2 (88.9) 7900814 7901014 ---- ----

HW3-214 HW4-214 PF3-214 PF4-214 2-1/4 (57.2) 3/4” - 1-1/4” 4-1/2 (114.3) 7900818 7901018 ---- ----

HW3-234 HW4-234 PF3-234 PF4-234 2-3/4 (69.9) 1-1/4” - 1-3/4” 4-1/2 (114.3) 7900818 7901018 ---- ----

HW3-314 HW4-314 PF3-314 PF4-314 3-1/4 (82.6) 1-3/4” - 2-1/4” 5-1/2 (139.7) 7900822 7901022 ---- ----

HW3-334 HW4-334 PF3-334 PF4-334 3-3/4 (95.3) 2-1/4” - 2-3/4” 5-1/2 (139.7) 7900822 7901022 ---- ----

HW3-400 HW4-400 PF3-400 PF4-400 4 (101.6) 2-1/2” - 3” 5-1/2 (139.7) 7900822 7901022 ---- ----

---- HW4-500 ---- PF4-500 5 (127.0) 3-1/2” - 4” 6-1/2 (165.1) ---- 7901026 ---- 7901060

---- HW4-600 ---- PF4-600 6 (152.4) 4-1/2” - 5” 7-1/2 (190.5) ---- 7901030 790059 7901059

All boxes of ITWTapcon come packaged with matching carbide-tipped bit. Tapcon is packaged 100 pieces per box and 500 pieces per master carton except HW4-600 and PF4-600 (400 in master carton).

139139




TAPCON ® MASONRY ANCHORS TAPCON ® MASONRY ANCHORS Technical DataTechnical Data

Approved for use in ACQ Treated Lumber

Head Style5/16" across flats hex with 5/8" diameter flange.Maxi-Set Tapcon®

Masonry Fastening SystemFor Tapcon® applications that require more anchor bearing surface.

Stainless Steel Tapcon®Masonry Fastening System410 Stainless Steel. Climaseal Coated

Applications• Shutters - protective and decorative.

• Screened porch and pool enclosures.

• Various sheet metal flashings.

• Decorative wrought iron.

• Wood nailers and plywood attachment.

Choose from a variety of TAPCON to meet your specifi c needs!

Technical DataPERFORMANCE TABLE

Tapcon® Anchors Ultimate Tension and Shear Values (Lbs/kN) in Hollow Block

ANCHOR DIA.

In. (mm)

ANCHOR EMBEDMENT

In. (mm)

LIGHT WEIGHT BLOCK MEDIUM WEIGHT BLOCK

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

3/16 (4.8) 1 (25.4) 220 (1.0) 400 (1.8) 340 (1.5) 730 (3.2)

1/4 (6.4) 1 (25.4) 250 (1.1) 620 (2.8) 500 (2.2) 1,000 (4.4)

Safe working loads for single installation under static loading should not exceed 25% of the ultimate load capacity.NOTE: 3/16” Tapcon requires 5/32” bit, 1/4” Tapcon requires 3/16” bit.

PERFORMANCE TABLE

Tapcon® Anchors Allowable Edge and Spacing Distances Tapcon®

PARAMETERANCHOR

DIA. Inch

NORMAL WEIGHT CONCRETE CONCRETE MASONRY UNITS (CMU)

FULL CAPACITY(Critical Distance

Inches)

REDUCED CAPACITY

(MinimalDistance Inches)

LOAD REDUCTION

FACTOR

FULL CAPACITY(Critical Distance

Inches)

REDUCED CAPACITY(Minimal Distance Inches)

LOAD REDUCTION FACTOR

Spacing Between Anchors - Tension 3/161/4

34

1-1/22

0.730.66

34

1-1/22

1.000.84

Spacing Between Anchors - Shear 3/161/4

34

1-1/22

0.830.82

34

1-1/22

1.000.81

Edge Distance - Tension 3/161/4

1-7/82-1/2

11-1/4

0.710.78

34

22

0.910.88

Edge Distance - Shear 3/161/4

2-1/43

1-1.81-1/2

0.700.59

34

22

0.930.80

For SI: 1 inch = 25.4 mm

PERFORMANCE TABLE

Tapcon® Anchors Ultimate Tension and Shear Values (Lbs/kN) in Concrete

ANCHOR DIA.

In. (mm)

MIN. DEPTH OF EMBEDMENT In.

(mm)

f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa) f’c = 5000 PSI (34.5 MPa)

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

TENSIONLbs. (kN)

SHEAR Lbs. (kN)

3/16 (4.8)

1 (25.4) 600 (2.7) 720 (3.2) 625 (2.8) 720 (3.2) 650 (2.9) 720 (3.2) 800 (3.6) 860 (3.8)

1-1/4 (31.8) 845 (3.7) 720 (3.2) 858 (3.8) 720 (3.2) 870 (3.9) 720 (3.2) 1,010 (4.5) 860 (3.8)

1-1/2 (38.1) 1,090 (4.8) 860 (3.8) 1,090 (4.8) 860 (3.8) 1,090 (4.8) 860 (3.8) 1,220 (5.4) 860 (3.8)

1-3/4 (44.5) 1,450 (6.5) 870 (3.9 1,455 (6.5) 870 (3.9) 1,460 (6.5) 990 (4.4) 1,730 (7.7) 990 (4.4)

1/4 (6.4)

1 (25.4) 750 (3.3) 900 (4.0) 775 (3.4) 900 (4.0) 800 (3.6) 1,360 (6.1) 950 (4.2) 1,440 (6.4)

1-1/4 (31.8) 1,050 (4.7) 900 (4.0) 1,160 (5.2) 900 (4.0) 1,270 (5.6) 1,360 (6.1) 1,515 (6.7) 1,440 (6.4)

1-1/2 (38.1) 1,380 (6.1) 1,200 (5.3) 1,600 (7.2) 1,200 (5.3) 1,820 (8.1) 1,380 (6.1) 2,170 (9.7) 1,670 (7.4)

1-3/4 (44.5) 2,020 (9.0) 1,670 (7.4) 2,200 (9.8) 1,670 (7.4) 2,380 (10.6) 1,670 (7.4) 2,770 (12.3) 1,670 (7.4)

Safe working loads for single installation under static loading should not exceed 25% of the ultimate load capacity.

140140




LARGE DIAMETER TAPCON (LDT)LARGE DIAMETER TAPCON (LDT)

141141




LARGE DIAMETER TAPCON (LDT)LARGE DIAMETER TAPCON (LDT)Technical DataTechnical Data

SELECTION CHART

LDT Carbon and Stainless SteelCarbon Steel with Zinc Plating: Meets ASTM B695 & B633 specifi cations for zinc plating of 5um = .0002” thickness. This coating is well suited for non-corrosive interior environments. Carbon Steel with EnvireX Coating: Provides additional corrosion protection for outdoor applications.

PART NUMBER

PARTNUMBER FOR

CARBON STEEL

ENVIREXCOATING

PARTNUMBER FOR 410

STAINLESS STEEL

ANCHORDIA.

In. (mm)

DRILL BITDIA.

In. (mm)

EFFECTIVELENGTHIn. (mm)

(See detail on left)

MAX. THICKNESSOF MATERIALS

TO BE FASTENEDIn. (mm)

QTY/WTPER BOX

lbs.

QTY/WTPER MASTER

CARTONlbs.

LDT-3816 —— SLDT-3816 3/8 (9.5) 5/16 (7.9) 1-3/4 (44.5) 1/4 (6.4) 50 / 3.0 400 / 24.0

LDT-3824 —— SLDT-3824 3/8 (9.5) 5/16 (7.9) 2-1/2 (63.5) 1 (25.4) 50 / 4.5 400 / 34.0

LDT-3830 LDT-3830X SLDT-3830 3/8 (9.5) 5/16 (7.9) 3 (76.2) 1-1/2 (38.1) 50 / 5.0 400 / 40.0

LDT-3840 LDT-3840X SLDT-3840 3/8 (9.5) 5/16 (7.9) 4 (101.6) 2-1/2 (63.5) 50 / 6.5 400 / 52.0

LDT-3850 LDT-3850X SLDT-3850 3/8 (9.5) 5/16 (7.9) 5 (127.0) 3-1/2 (89.0) 40 / 7.5 320 / 60.0

LDT-1230 LDT-1230X SLDT-1230 1/2 (12.7) 7/16 (11.1) 3 (76.2) 1 (25.4) 25 / 4.5 150 / 27.0

LDT-1240 LDT-1240X SLDT-1240 1/2 (12.7) 7/16 (11.1) 4 (101.6) 2 (50.8) 25 / 6.0 150 / 36.6

LDT-1250 LDT-1250X SLDT-1250 1/2 (12.7) 7/16 (11.1) 5 (127.0) 3 (76.2) 25 / 7.6 150 / 45.6

LDT-1260 —— —— 1/2 (12.7) 7/16 (11.1) 6 (152.4) 4 (101.6) 20 / 9.0 120 / 54.0

LDT-5830 —— —— 5/8 (15.9) 1/2 (12.7) 3 (76.2) 1/4 (6.4) 10 / 3.5 100 / 35.0

LDT-5840 —— —— 5/8 (15.9) 1/2 (12.7) 4 (101.6) 1-1/4 (31.8) 10 / 4.0 100 / 40.0

LDT-5850 —— —— 5/8 (15.9) 1/2 (12.7) 5 (127.0) 2-1/4 (57.1) 10 / 4.7 100 / 47.0

LDT-5860 —— —— 5/8 (15.9) 1/2 (12.7) 6 (152.4) 3-1/4 (82.6) 10 / 5.4 50 / 27.0

LDT-3444 —— —— 3/4 (19.1) 5/8 (15.9) 4-1/2 (114.3) 1-1/4 (31.8) 10 / 7.4 50 / 37.0

LDT-3454 —— —— 3/4 (19.1) 5/8 (15.9) 5-1/2 (139.7) 2-1/4 (57.1) 10 / 8.1 50 / 40.5

LDT-3462 —— —— 3/4 (19.1) 5/8 (15.9) 6-1/4 (158.8) 3 (76.2) 10 / 9.1 30 / 27.3

* The stainless steel LDT’s will be gold in color in order to differentiate them from the carbon steel anchors which are silver.

DESIGN GUIDEFor proper selection of anchor diameters based upon pre-drilled holes through base plates and fi xtures to be fastened.

HOLE DIAMETER THROUGH FIXTURE

In. (mm)

SUGGESTED LDT DIAMETER

In. (mm)

7/16 (11.1) 3/8 (9.5)

1/2 (12.7) 3/8 (9.5)

9/16 (14.3) 1/2 (12.7)

5/8 (15.9) 1/2 (12.7)

3/4 (19.1) 5/8 (15.9)

7/8 (22.2) 3/4 (19.1)

LENGTH INDICATION CODE*

CODE LENGTH OF ANCHOR In. (mm)

A 1-1/2 < 2 (38.1 < 50.8)

B 2 < 2-1/2 (50.8 < 63.5)

C 2-1/2 < 3 (63.5 < 76.2)

D 3 < 3-1/2 (76.2 < 88.9)

E 3-1/2< 4 (88.9 < 101.6)

F 4 < 4-1/2 (101.6 < 114.3)

G 4-1/2 < 5 (114.3 < 127.0)

H 5 < 5-1/2 (127.0 < 139.7)

I 5-1/2 < 6 (139.7 < 152.4)

J 6 < 6-1/2 (152.4 < 165.1

* Located on top of anchor for easy inspection.

142142




LARGE DIAMETER TAPCON (LDT)LARGE DIAMETER TAPCON (LDT)Technical DataTechnical Data

PERFORMANCE TABLELDT Anchors Ultimate Tension and Shear Values (Lbs/kN) in Concrete

ANCHORDIA.

In. (mm)

EMBEDMENTDEPTHIn. (mm)

f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa)

TENSIONLbs. (kN)

SHEARLbs. (kN)

TENSIONLbs. (kN)

SHEARLbs. (kN)

TENSIONLbs. (kN)

SHEARLbs. (kN)

3/8 (9.5)

1-1/2 (38.1) 1,336 (5.9) 2,108 (9.4) 1,652 (7.3) 2,764 (12.3) 1,968 (8.8) 3,416 (15.2)

2 (50.8) 1,492 (6.6) 3,036 (13.5) 2,024 (9.0) 3,228 (14.4) 2,552 (11.4) 3,420 (15.2)

2-1/2 (63.5) 3,732 (16.6) 3,312 (14.7) 3,748 (16.7) 3,364 (15.0) 3,760 (16.7) 3,424 (15.2)

3-1/2 (88.9) 5,396 (24.0) 3,312 (14.7) 6,624 (29.5) 3,368 (15.0) 7,852 (34.9) 3,428 (15.2)

1/2 (12.7)

2 (50.8) 3,580 (15.9) 5,644 (25.1) 3,908 (17.4) 6,512 (29.0) 4,236 (18.8) 7,380 (32.8)

3-1/2 (88.9) 7,252 (32.3) 6,436 (28.6) 8,044 (35.8) 7,288 (32.4) 8,836 (39.3) 8,140 (36.2)

4-1/2 (114.3) 10,176 (45.3) 7,384 (32.8) 10,332 (46.0) 7,968 (35.4) 10,488 (46.7) 8,552 (38.0)

5/8 (15.9)

2-3/4 (69.9) 5,276 (23.5) 8,656 (38.5) 6,560 (29.2) 11,064 (49.2) 7,844 (34.8) 13,476 (59.9)

3-1/2 (88.9) 7,972 (35.5) 10,224 (45.5) 9,848 (43.8) 12,144 (54.0) 11,724 (52.2) 14,060 (62.5)

4-1/2 (114.3) 11,568 (51.5) 12,316 (54.8) 13,432 (59.8) 13,580 (60.4) 16,892 (75.1) 14,840 (66.0)

3/4 (19.1)

3-1/4 (82.6) 6,876 (30.6) 7,140 (31.8) 9,756 (43.4) 10,728 (47.7) 12,636 (56.2) 14,316 (63.6)

4-1/2 (114.3) 10,304 (45.8) 13,120 (58.4) 14,424 (64.2) 16,868 (75.0) 18,540 (82.5) 20,612 (91.7)

5-1/2 (139.7) 13,048 (58.0) 17,908 (79.7) 18,156 (80.8) 21,718 (96.9) 23,268 (130.5) 25,652 (114.1)

PERFORMANCE TABLE

LDT Anchors Ultimate Tension Load (Lbs/kN) in Concrete Block(anchors should be installed by hand in hollow block)

ANCHORDIA.

In. (mm)


HOLLOW CONCRETE BLOCK GROUT FILLED CONCRETE BLOCK

TENSIONLbs. (kN)

SHEARLbs. (kN)

TENSIONLbs. (kN)

SHEARLbs. (kN)

3/8 (9.5) 1-1/2 (38.1) 916 (4.1) 3,176 (14.1) 1,592 (7.1) 3,900 (17.3)

1/2 (12.7) 2-1/2 (63.5) ---- ---- ---- ---- 5,924 (26.4) 6,680 (29.7)

PERFORMANCE TABLE

LDT Anchors Recommended Edge & Spacing Requirements for Tension Loads*Carbon and Stainless Steel

ANCHORDIA.

In. (mm)


EDGE DISTANCE

REQUIRED TO OBTAIN MAX.

WORKING LOAD In. (mm)

LOAD FACTOR APPLIED AT MIN. EDGE DISTANCE

1-3/4 Inches (44mm)

SPACING DISTANCE

REQUIRED TO OBTAIN MAX.

WORKING LOAD In. (mm)

LOAD FACTOR APPLIED AT

MIN. SPACING DISTANCE

3 Inches (76mm)

3/8 (9.5)

1-1/2 (38.1) 2 (50.8) 70% 6 (152.4) 44%

2 (50.8) 2 (50.8) 70% 6 (152.4) 44%

2-1/2 (63.5) 3 (76.2) 70% 6 (152.4) 44%

3-1/2 (88.9) 4 (101.6) 70% 6 (152.4) 44%

1/2 (12.7)

2 (50.8) 2-1/4 (57.2) 65% 8 (203.2) 27%

3-1/2 (88.9) 3 (76.2) 65% 8 (203.2) 27%

4-1/2 (114.3) 4 (101.6) 65% 8 (203.2) 27%

* Edge and spacing distance shall be divided by .75 when anchors are placed in structural lightweight concrete. Linear interpolation may be used for intermediate spacing and edge distances.

For 5/8” and 3/4” LDT Anchors, the critical edge distance for these anchors is 10 times the anchor diameter. The edge distance of these anchors may be reduced to 1-3/4” provided a 0.65 load factor is used for tension loads, a 0.15 load factor is used for shear loads applied perpendicular to the edge, or a 0.60 load factor is used for shear loads applied parallel to the edge. Linear interpolation may be used for intermediate edge distances.

PERFORMANCE TABLE

LDT Anchors Anchoring Overhead in 3000 PSI LightweightLDT Anchors Concrete On Metal Deck

ANCHORDRILL HOLEDIAMETER

In. (mm)


3000PSI (20.7 MPa) CONCRETE

ULTIMATE TENSION LOADLbs. (kN)

ALLOWABLE WORKING LOAD

Lbs. (kN)

3/8” LDT 5/16 (7.9) 1-1/2 (38.1)Upper Flute 2,889 (12.9) 722 (3.2)

Lower Flute 1,862 (8.3) 465 (2.1)

143143




Std. Std. Size Box Ctn. 3/16" x 1-1/4" 100 500 3/16" x 1-3/4" 100 500 3/16" x 2-1/4" 100 500 3/16" x 2-3/4" 100 500

1/4" x 1-1/4" 100 500 1/4" x 1-3/4" 100 500 1/4" x 2-1/4" 100 500 1/4" x 3" 100 500

3/8" x 1-3/4" 50 250 3/8" x 2-1/2" 50 250 3/8" x 3" 50 250 3/8" x 4" 50 250

1/2" x 2" 50 200 1/2" x 2-1/2" 50 200 1/2" x 3" 50 150 1/2" x 4" 50 150 1/2" x 5" 50 100 1/2" x 6" 25 75

5/8" x 3" 25 100 5/8" x 4" 25 100 5/8" x 5" 25 75 5/8" x 6" 25 75

3/4" x 3" 20 60 3/4" x 4" 20 60 3/4" x 5" 20 60 3/4" x 6" 20 60 3/4" x 8" 10 40

* The published length is measured from below the hex washer head to the end of the anchor.

Hex Head Anchors

WEDGE BOLT BY POWERSWEDGE BOLT BY POWERS

144144




The Inside Story About Mechanical and Adhesive Anchors

Expansion TypeTension loads are transferred to the base material through a portion of the anchor that is expanded inside the drill hole.

Examples: Red Head Redi-Bolts, Dynabolts, Multi-Set II Anchors and Hammer-Sets.

Adhesive TypeResistance to tension loads is provided by the presence of an adhesive

between the threaded rod (or rebar) and the inside walls of the drill hole.

Examples: Epcon A7, C6, G5, Maxima 7 Capsules and Impact Capsules

Keying TypeHolding strength comes from a portion of an anchor that is expanded into a hollow space in a base material that contains voids such as concrete block or brick.

Examples: Epcon adhesives used in screen tubes or umbrella insert

Friction TypeLoad capacity is created by driving a fastener into a pre-drilled hole that is

slightly smaller than the fastener itself.

Examples: Redi-Drives

Mechanical Interlocking TypeTension loads are resisted by threads on the fastener engaging with threads cut into the base material.

Examples: LDT, Tapcon and E-Z Ancors

Types of Anchors

CONCRETE FASTENING SYSTEMSCONCRETE FASTENING SYSTEMS

145145




When anchors are loaded to their maximum capacity, several different types (modes) of failure are possible depending on the type of anchor, strength of the base material, embedment depth, location of the anchor, etc. Common modes of failure include:

Modes of Failure

Concrete Spill ConeOccurs at shallow embedments where the resistance of the base material is less than the resistance of the anchor and the base material fails.

Steel BreakageThe capacity of the anchorage exceeds the strength of the steel anchor or rod

material.

Anchor PulloutBase material adjacent to the extension portion of an anchor crushes, resulting in the anchor pulling out of the hole until the capacity of the spill cone is reached, at which point the concrete will spill. This type of failure happens more commonly when anchors are set with deep embedment depths.

Bond FailureShear failure of the adhesive at rod adhesive interface or adhesive-base

material interface. Occurs more commonly in deep embedments usinghigh strength steel rods.

Edge Distance and Spacing ReductionReduces the holding values, when anchors are placed too close to the edge. This also occurs when two or more anchors are spaced closely together. See suggested edge distance, anchor spacing distances and reduction values in the product sections.

CONCRETE FASTENING SYSTEMSCONCRETE FASTENING SYSTEMS

146146




Redi-Bolt® AnchorsReduces Cost, Increases Safety and Improves Anchoring Performance

• Select a carbide drill bit with a diameter equal to the anchor diameter. Drill hole to any depth exceeding the desired embedment (see chart for recommended embedment).

• Clean hole or continue drilling additional depth to accommodate drill fines (concrete dust).

Installation Steps

• Drive the anchor into the hole through material being fastened until washer is flush with material.

• Expand Redi-Bolt by tightening the anchor 3 to 5 turns, or to the specified torque requirements (seeinstallation instructions).

Description/Suggested Specifications:Heavy Duty Sleeve AnchorsSpecified for anchorage into solid concrete and concrete fill.The Redi-Bolt features a patented double expansion sleeve, Grade 5, high strength threaded bolt, a steel expander cone and washer. The exposed end of the anchor is stamped by Red Head to identify anchor length post-installation. Anchors should be installed with carbide type drill bits made in accordance to ANSI B212.15-1994.

Advantages:Redi-Bolt provides up to 22% more pullout and up to 48% more shear than wedge anchors; up to 40% more pullout and 61% more shear than traditional sleeve anchors. This means reduced costs because with higher tension and shear values you can:

• Use a smaller diameter anchor• Use a smaller, less expensive drill bit• Drill faster because of smaller hole and shallower embedment• Threaded bolt can be removed and reinstalled into expansion assembly

Vibration ResistanceOntario Hydro Test Report Findings: 1/2" Redi-Bolt anchor withstood two million dynamic load cycles with no indication of slip or unusual change.

Approvals/listings• Meets or exceeds U.S. Government G.S.A. specification FF-S-325 Group II, Type 3, Class 1• Ontario Hydro Vibration Test• Data for seismic conditions tested to ICBO criteria by ICBO lab

REDI-BOLTREDI-BOLT® ® ANCHORSANCHORS

147147




Technical Data

Redi-Bolt® AnchorsReduces Cost, Increases Safety and Improves Anchoring Performance

ANCHOR MINIMUM MaxIMUM Qty/wt DRILL Anchor EMBEDMENT FIXTURE INSTALLATION Qty/Wt per master DIAMETER LENGTH IN CONCRETE THICKNESS Length ID Code per box carton In. (mm) In. (mm) In. (mm) In. (mm) Ft. Lbs. (Nm) letter lbs. lbs. 3/8 (9.5) 2 (50.8) 1-1/2 (38.1) 1/2 (12.7) 35 (47.5) B 50/3.7 400/30 3/8 (9.5) 3 (75.2) 2 (50.8) 1 (25.4) 35 (47.5) D 50/5.4 400/44 1/2 (12.7) 3-3/4 (95.3) 2-1/2 (63.5) 1-1/4 (31.8) 60 (81.4) E 25/5.9 200/48 1/2 (12.7) 4-3/4 (120.7) 2-1/2 (63.5) 2-1/4 (57.2) 60 (81.4) G 25/6.4 200/56 1/2 (12.7) 5-3/4 (146.5) 2-1/2 (63.5) 3-1/4 (82.6) 60 (81.4) I 25/8.2 200/66 5/8 (15.9) 4 (101.6) 2-3/4 (69.9) 1-1/4 (31.8) 100 (135.7) F 15/6.6 150/67 5/8 (15.9) 5 (127.0) 2-3/4 (69.9) 2-1/4 (57.2) 100 (135.7) H 15/7.9 150/80 5/8 (15.9) 6 (152.4) 2-3/4 (69.9) 3-1/4 (82.6) 100 (135.7) J 10/6.1 150/31 3/4 (19.1) 4-1/4 (108.0) 3 (75.2) 1-1/4 (31.8) 120 (162.8) F 10/6.3 50/32 3/4 (19.1) 5-1/4 (133.4) 3 (75.2) 2-1/4 (57.2) 120 (162.8) H 10/7.5 50/38 3/4 (19.1) 7-1/4 (184.2) 3 (75.2) 4-1/4 (108.0) 120 (162.8) L 5/5.0 50/50

* Grade 2 Hollow Block Anchor

Redi-Bolt Removable Anchors Selection Chart

Recommended Spacing And Edge Distance Requirements For Tension Loads

Ultimate Shear And Tension Values (Lbs/kN) In 4000 Psi (27.6 MPa) Concrete

Min. Allowable Min. Allowable Edge Distance Edge DIstance At Spacing Required Spacing Between Anchors Anchor Installation Required To Obtain Which The Load Factor To Obtain Max. Load Factor Dia. Torque Max. Working Load Applied = 0.75 Working Load Applied = 0.50 In. (mm) Ft. Lbs. (Nm) In. (mm) In. (mm) In. (mm) In. (mm) 3/8 (9.5) 35 (47.5) 3-3/4 (95.3) 1-7/8 (47.6) 4-1/2 (114.3) 1-7/8 (47.6) 1/2 (12.7) 60 (81.4) 5 (127.0) 2-1/2 (63.5) 6 (152.4) 2-1/2 (63.5) 5/8 (15.9) 100 (135.7) 6-1/4 (158.8) 3-1/8 (79.4) 7-1/2 (190.5) 3-1/8 (79.4) 3/4 (19.1) 120 (162.8) 7-1/2 (190.5) 3-3/4 (95.3) 9 (228.6) 3-3/4 (95.3)

Linear interpolation may be used for intermediate spacing and edge distances.

Anchor Dia. Embedment Installation Torque Ultimate Tension Ultimate Shear In. (mm) In. (mm) Ft. Lbs. (Nm) Lbs. (kN) Lbs. (kN) 3/8 (9.5) 2 (50.8) 35 (47.5) 5,195 (23.1) 7,730 (34.4) 2-1/2 (63.5) 5,870 (26.1) 8,018 (35.7) 1/2 (12.7) 2-1/2 (63.5) 60 (81.4) 6,931 (30.8) 10,132 (45.1) 4 (101.6) 10,518 (46.8) 13,005 (57.9) 5/8 (15.9) 2-3/4 (69.9) 100 (135.7) 8,585 (38.2) 13,484 (60.0) 5 (127.0) 19,219 (85.5) 21,040 (93.6) 3/4 (19.1) 3 (76.2) 120 (162.8) 10,574 (47.0) 18,733 (83.3) 6 (152.4) 20,267 (90.2) 29,668 (132.0)

Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

Ultimate Shear And Tension Values (Lbs/kN) In C90 Grout-Filled CMU Anchor Dia. Embedment Installation Torque Ultimate Tension Ultimate Shear In. (mm) In. (mm) Ft. Lbs. (Nm) Lbs. (kN) Lbs. (kN) 3/8 (9.5) 2 (50.8) 20 (27.1) 3,798 (16.9) 4,855 (21.6) 2-1/2 (63.5) 3,896 (17.3) 4,855 (21.6) 1/2 (12.7) 2-1/2 (63.5) 35 (47.5) 3,993 (17.8) 6,867 (30.5) 4 (101.6) 4,182 (18.6) 6,867 (30.5) 5/8 (15.9) 2-3/4 (69.9) 60 (81.4) 3.990 (17.7) 11,777 (52.4) 5 (127.0) 4,634 (20.5) 12,525 (93.6) 3/4 (19.1) 3 (76.2) 85 (115.3) 4,693 (20.9) 18,733 (55.7) 6 (152.4) 5,908 (26.3) 13,964 (62.1)

Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

REDI-BOLTREDI-BOLT® ® ANCHORSANCHORS

148148




Dynabolt® Sleeve AnchorsVersatile Heavy-Duty Sleeve Anchors

Approvals/ListingsMeets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group II, Type 3, Class 3

Factory Mutual

SBCCI Compliance Report – #9570

California State Fire Marshal

Installation Steps

1. Use a bit with a diameter equal to the anchor. See selection chart to determine proper size bit for anchor used. Drill hole to any depth exceeding minimum embedment. Clean hole.

2. Insert assembled anchor into hole, so that washer or head is flush with materials to be fastened.

Description/suggested specificationsSleeve Type AnchorsSpecified for anchorage into concrete, masonry, grout filled block and hollow blockSleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and washer.

Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.

Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994.

Anchors are tested to ASTM E488 criteria.

3. Expand anchor by tighteningnut or head 2 to 3 turns.

DYNABOLTDYNABOLT® ® SLEEVE ANCHORSSLEEVE ANCHORS

Dynabolt Sleeve Anchors Performance TableUltimate Tension and Shear Values In Concrete* And (Lbs/kN)

Anchor Installation Bolt Embedment f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa) Dia. Torque Dia. Depth Anchor Tension Shear Tension Shear Tension Shear In. (mm) Ft. Lbs. (Nm) In. (mm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)1/4 (6.4) 3.5 (4.7) No. 10 1-1/8 (28.6) 1,200 (5.3) 1,620 (7.2) 1,600 (7.1) 1,620 (7.2) 2,100 (8.5) 1,620 (7.2)5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,400 (6.2) 2,040 (9.1) 1,920 (8.5) 2,220 (9.9) 2,600 (11.6) 2,400 (10.7)3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,560 (11.4) 2,240 (10.0) 2,800 (12.5) 3,100 (13.8) 3,040 (13.5)1/2 (12.7) 20 (27.1) 3/8 (9.5) 1-7/8 (47.6) 2,220 (9.9) 4,000 (17.8) 3,140 (14.0) 4,500 (20.0) 4,400 (19.6) 5,000 (22.2)5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,080 (13.7) 6,440 (28.6) 4,400 (19.6) 7,240 (32.2) 6,120 (27.2) 8,080 (35.9)3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 4,200 (18.7) 10,200 (45.4) 5,940 (26.4) 11,600 (51.6) 8,900 (39.6) 13,100 (58.3)

Carbonor

Stainless

Dynabolt Sleeve Anchors Performance TableUltimate Tension and Shear Values In Lightweight Concrete (Lbs/kN)*

Anchor Installation Bolt Minimum f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa) Dia. Torque Dia. Embedment Anchor Tension Shear Tension Shear In. (mm) Ft. Lbs. (Nm) In. (mm) Depth In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)1/4 (6.4) 3.5 (4.7) No. 10 1-1/8 (28.6) 1,080 (4.8) 1,620 (7.2) 1,220 (5.2) 1,940 (8.6)5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,260 (5.6) 1,680 (7.5) 1,440 (6.4) 2,220 (9.9)3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,300 (10.2) 2,240 (10.0) 2,800 (12.5)1/2 (12.7) 20 (27.1) 3/8 (9.5) 1-7/8 (47.6) 2,600 (11.6) 3,920 (17.4) 3,160 (14.1) 4,840 (21.5)5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,240 (14.4) 5,600 (24.9) 4,300 (19.1) 7,840 (34.9)3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 3,640 (16.2) 8,640 (38.4) 5,800 (25.8) 12,480 (55.5)

Carbonor

Stainless

Technical DataTension and Shear

149149




Dynabolt® Sleeve AnchorsVersatile Heavy-Duty Sleeve Anchors Sizes

Dynabolt Carbon Steel

Zinc

Pla

ting

304

Stai

nles

s St

eel

Anchor Max. Dia. & Thickness Qty/Wt Drill Effective of Material Per Bit Size Anchor Bolt Dia./ Minimum to be Qty/Wt MasterHead (Threads) Length* Threads Embedment Fastened Per Box CartonStyle Per Inch In. (mm) Per Inch In. (mm) In. (mm) Lbs. Lbs.Acorn Nut 1/4" - 20 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.9 1000/ 20

1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.6 1000/ 27

2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.7 1000/ 38

Hex Nut 1/4" - 20 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.6 1000/ 17

1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.3 1000/ 24

2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.4 1000/ 35

5/16" - 18 1-1/2 (38.1) 1/4" /20 1-1/4 (31.8) 1/4 (6.4) 100/ 4.0 1000/ 41

2-1/2 (63.5) 1/4" /20 1-1/4 (31.8) 1-1/4 (31.8) 100/ 5.9 800/ 47

3/8" - 16 1-7/8 (47.6) 5/16" /18 1-1/2 (38.1) 3/8 (9.5) 50/ 3.5 500/ 36

3 (76.2) 5/16" /18 1-1/2 (38.1) 1-1/2 (38.1) 50/ 4.9 400/ 40

1/2" - 13 2-1/4 (57.2) 3/8" /16 1-7/8 (47.6) 3/8 (9.5) 25/ 3.3 250/ 34

3 (76.2) 3/8" /16 1-7/8 (47.6) 1-1/8 (28.6) 25/ 4.0 200/ 33

4 (101.6) 3/8" /16 1-7/8 (47.6) 2-1/8 (54.0) 25/ 5.3 200/ 44

5/8" - 11 2-1/4 (57.2) 1/2" /13 2 (50.8) 1/4 (6.4) 25/ 6.3 150/ 38

3 (76.2) 1/2" /13 2 (50.8) 1 (25.4) 25/ 7.0 150/ 46

4-1/4 (108.0) 1/2" /13 2 (50.8) 2-1/4 (57.2) 10/ 3.9 100/ 41

6 (152.4) 1/2" /13 2 (50.8) 4 (101.6) 10/ 4.9 50/ 25

3/4" - 10 2-1/2 (63.5) 5/8" /11 2-1/4 (57.2) 1/4 (6.4) 10/ 4.7 50/ 25

4 (101.6) 5/8" /11 2-1/4 (57.2) 1-3/4 (44.5) 5/ 3.2 50/ 33

6-1/4 (158.8) 5/8" /11 2-1/4 (57.2) 4 (101.6) 5/ 4.3 50/ 44

Phillips 1/4" - 20 1-1/2 (38.1) 3/16" /24 1-1/8 (28.6) 3/8 (9.5) 100/ 1.9 1000/ 21

Flat Head (head dia. .477) 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 2.7 1000/ 28

3-1/8 (79.4) 3/16" /24 1-1/8 (28.6) 2 (50.8) 100/ 3.8 1000/ 38

4 (101.6) 3/16" /24 1-1/8 (28.6) 2-7/8 (73.0) 100/ 4.7 1000/ 48

3/8" - 16 2-7/8 (73.0) 5/16" /18 1-1/2 (38.1) 1-3/8 (34.9) 50/ 3.8 500/ 40

(head dia. .722) 4 (101.6) 5/16" /18 1-1/2 (38.1) 2-1/2 (63.5) 50/ 5.3 400/ 4

5 (127.0) 5/16" /18 1-1/2 (38.1) 3-1/2 (88.9) 50/ 5.6 300/ 40

6 (152.4) 5/16" /18 1-1/2 (38.1) 4-1/2 (114.3) 50/ 8.0 300/ 48

Threshold 1/4" - 20 2-1/4 (57.2) 3/16" /24 1-1/8(28.6) 1-1/8 (28.6) 100/ 2.5 1000/ 25

Flat Head (head dia. .385)

Round Head 1/4" - 20 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 1.9 1000/ 20

2 (50.8) 3/16" /24 1-1/8 (28.6) 7/8 (22.2) 100/ 2.7 1000/ 28

2-7/8 (73.0) 3/16" /24 1-1/8 (28.6) 1-3/4 (44.5) 100/ 3.7 1000/ 38

3/8" - 16 2-5/8 (66.7) 5/16" /18 1-1/2 (38.1) 1-1/8 (28.6) 50/ 3.9 500/ 41

Tie Wire 5/16" - 18 1-1/2 (38.1) 1/4" /20 1-1/2 (38.1) 9/32 (7.1) 100/ 4.9 1000/ 50

Hex Coupling 3/8" - 16 1-7/8 (47.6) 3/8" /16 1-1/2 (38.1) -- -- 50/ 6.0 250/ 30

(Rod Hanger) Hanger

1/2" - 13 2-1/4 (57.2) 1/2" /13 1-7/8 (47.6) -- -- 25/ 6.5 125/ 34

Hanger

DYNABOLTDYNABOLT® ® SLEEVE ANCHORSSLEEVE ANCHORS

Installation Lightweight Medium Weight Anchor Torque Bolt Minimum Anchor Hollow Core Grout Filled Hollow Core Grout Filled Dia. Ft. Lbs. Dia. Embedment Type Tension Shear T ension Shear T ension Shear T ension Shear In. (mm) (Nm) In. (mm) Depth In. (mm) (Steel) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) 1/4 (6.4) 3.5 (4.7) 3/16 (4.8) 1-1/8 (28.6) Carbon 1,120 1,360 1,120 1,360 1,120 1,620 1,120 1,360 (5.0) (6.0) (5.0) (6.0) (5.0) (7.2) (5.0) (6.0)

Stainless 640 1,620 640 1,620 640 1,620 640 1,620 (2.8) (7.2) (2.8) (7.2) (2.8) (7.2) (2.8) (7.2)

3/8 (9.5) 15 (20.3) 5/16 (7.9) 1-1/2 (38.1) Carbon 1,360 2,560 1,360 2,560 1,360 2,560 1,360 2,560 (6.0) (11.4) (6.0) (11.4) (6.0) (11.4) (6.0) (11.4)

Stainless 1,160 2,560 1,160 2,560 1,160 2,560 1,160 2,560 (5.2) (11.4) (5.2) (11.4) (5.2) (11.4) (5.2) (11.4)

1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6) Carbon -- -- 2,220 4,000 -- -- 2,220 4,000 -- -- (9.9) (17.8) -- -- (9.9) (17.8)

Stainless -- -- 2,100 4,000 -- -- 2,100 4,000 -- -- (9.3) (17.8) -- -- (9.3) (17.8)

5/8 (15.9) 55 (74.6) 1/2 (12.7) 2 (50.8) Carbon -- -- 3,080 6,440 -- -- 3,080 6,440 -- -- (13.7) (28.6) -- -- (13.7) (28.6)

Stainless -- -- 3,080 6,440 -- -- 2,820 6,440 -- -- (13.7) (28.6) -- -- (12.5) (28.6)

3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/2 (63.5) Carbon -- -- 4,200 10,200 -- -- 4,200 10,200 -- -- (18.7) (45.4) -- -- (18.7) (45.4)

* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values. The tabulated values are for anchors installed in a minimum of 12 diameters on center and a minimum edge distance of six diameters for 100 percent anchor efficiency. Spacing and edge distance may be reduced to six-diameter spacing and three-diameter edge distance, provided the values are reduced 50 percent. Linear interpolation may be used for intermediate spacings and edge distances.

Combined Shear and Tension Loading—for Dynabolt AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation: (Ps/Pt) + (Vs/Vt) <=1

Ps = Applied tension load Vs = Applied shear load Pt = Allowable tension load Vt = Allowable shear load

Dynabolt Sleeve Anchors Performance TableUltimate Tension and Shear Values In Masonry Units (Lbs/kN)*

150150




Trubolt® Wedge AnchorsDependable, Heavy-Duty, Inspectable, Wedge Type Expansion Anchor

• Using a bit whose diameter equals the anchor diameter, drill hole to any depth exceeding the minimum embedment. Clean hole.

• Assemble anchor with nut andwasher so that the top of the nut isflush with the top of the anchor.Drive anchor through material to befastened so that nut and washer are flush with surface of material.

Installation Steps

• Expand anchor by tightening nut 3to 5 turns, or to the specific torquerequirement (see selection chart).

Description/suggested specificationsWedge Type Anchors Specified for anchorage into concrete.Wedge anchors feature a type 18-8 stainless steel split expansion ring and a threaded stud bolt body and integral cone expander, nut and washer. Anchor bodies are made of plated carbon steel, hot-dipped galvanized carbon steel, type 304 stainless steel or type 316 stainless steel as identified in the drawings or other notations.

The exposed end of the anchor is stamped to identify anchor length. Stampings should be preserved during installation for any subsequent embedment verification.

Use carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 to install anchors.

Anchors are tested to ASTM E488 criteria and listed by ICBO and SBCCI. Anchors are listed by the following agencies as required by the local building code: UL, FM, City of Los Angeles, California State Fire Marshal and Cal Trans.

Approvals/listings• Meets or exceeds U.S. Government G.S.A. Specification FF-S 325 Group II, Type 4, Class 1• Underwriters Laboratories• Factory Mutual• ICBO Evaluation Service, Inc. – #ER-1372 (including seismic loading conditions)• City of Los Angeles – #RR2748• SBCCI Compliance Report – #9570• California State Fire Marshal• Cal Trans

DYNABOLTDYNABOLT® ® WEDGE ANCHORSWEDGE ANCHORS

151151




Sizes

Max. Anchor Dia. Thickness Qty/wt Thread & Drill Bit Overall of material Qty/Wt per master Length Size (threads) Length to be fastened per box carton In. (mm) per inch In. (mm) In. (mm) lbs. lbs. 3/4 (19.1) 1/4" - 20 1-3/4 (44.5) 3/8 (9.5) 100/ 3.1 1000/ 32 1-1/4 (31.8) 2-1/4 (57.2) 7/8 (22.2) 100/ 3.6 1000/ 37

2-1/4 (57.2) 3-1/4 (82.6) 1-7/8 (47.6) 100/ 4.7 800/ 39

1-1/8 (28.6) 3/8" - 16 2-1/4 (57.2) 3/8 (9.5) 50/ 4.1 500/ 41

1-5/8 (41.3) 2-3/4 (69.9) 7/8 (22.2) 50/ 4.7 400/ 39

1-7/8 (47.6) 3 (76.2) 1-1/8 (28.6) 50/ 5.0 400/ 41

2-5/8 (66.7) 3-3/4 (95.3) 1-7/8 (47.6) 50/ 5.9 300/ 36

2-3/4 (69.9) 5 (127.0) 3-1/8 (79.4) 50/ 7.4 250/ 38 2-1/4 (57.2) 7 (177.8) 5-1/8 (130.2) 50/ 10.4 250/ 53

1-1/4 (31.8) 1/2" - 13 2-3/4 (69.9) 1/8 (3.2) 25/ 4.6 200/ 38

2-1/4 (57.2) 3-3/4 (95.3) 1 (25.4) 25/ 5.7 150/ 35

2-3/4 (69.9) 4-1/4 (108.0) 1-1/2 (38.1) 25/ 6.2 150/ 38

3 (76.2) 4-1/2 (114.3) 1-3/4 (44.5) 25/ 6.5 150/ 39 3 (76.2) 5-1/2 (139.7) 2-3/4 (69.9) 25/ 7.7 150/ 47

4-1/2 (114.3) 7 (177.8) 4-1/4 (108.0) 25/ 9.3 150/ 57

1-3/4 (44.5) 5/8" - 11 3-1/2 (88.9) 1/8 (3.2) 10/ 3.6 100/ 37 2-1/2 (63.5) 4-1/4 (108.0) 7/8 (22.2) 10/ 4.1 100/ 42

3-1/4 (82.6) 5 (127.0) 1-5/8 (41.3) 10/ 4.7 100/ 48

3-1/2 (88.9) 6 (152.4) 2-5/8 (66.7) 10/ 5.4 50/ 28 4-1/2 (114.3) 7 (177.8) 3-5/8 (92.1) 10/ 6.2 30/ 19

3-1/2 (88.9) 8-1/2 (215.9) 5-1/8 (130.2) 10/ 8.0 30/ 25 1-3/4 (44.5) 10 (254.0) 6-5/8 (168.3) 10/ 9.4 30/ 29

1-3/4 (44.5) 3/4" - 10 4-1/4 (108.0) 1/4 (31.8) 10/ 6.8 60/ 42 2-1/4 (57.2) 4-3/4 (120.7) 3/4 (19.1) 10/ 7.4 60/ 45

3 (76.2) 5-1/2 (139.7) 1-1/2 (38.1) 10/ 8.1 50/ 41 3-3/4 (95.3) 6-1/4 (158.8) 2-1/4 (57.2) 10/ 9.1 30/ 28

4-1/2 (114.3) 7 (177.8) 3 (76.2) 10/ 9.7 30/ 30 3-1/2 (88.9) 8-1/2 (215.9) 4-1/2 (114.3) 10/ 12.3 30/ 38 1-3/4 (44.5) 10 (254.0) 6 152.4) 10/ 14.0 30/ 43 1-3/4 (44.5) 12 (304.8) 8 (203.2) 10/ 16.6 30/ 51

2-1/2 (63.5) 7/8" - 9 6 (152.4) 1-3/8 (34.9) 5/ 6.3 25/ 32 2-1/2 (63.5) 8 (203.2) 3-3/8 (85.7) 5/ 8.1 15/ 25 2-1/2 (63.5) 10 (254.0) 5-3/8 (136.5) 5/ 9.8 15/ 30

2-1/2 (63.5) 1" - 8 6 (152.4) 1/2 (12.7) 5/ 8.3 25/ 43 2-1/2 (63.5) 9 (228.6) 3-1/2 (88.9) 5/ 11.6 15/ 36 2-1/2 (63.5) 12 (304.8) 6-1/2 (165.1) 5/ 15.0 15/ 46

3-1/2 (88.9 1-1/4" - 7 9 (228.6) 5-1/4 (133.4) 5/ 18.0 15/ 55

T ie Wire N/A 1/4" - 20 2-3/16 (55.6) 9/32 (7.1) 100/ 3.6 1000/ 36

Zinc

Pla

ting

Hot

-Dip

ped

Gal

vani

zed

304

Stai

nles

s St

eel

316

Stai

nles

s St

eelTruBolt Removable Anchors Selection Chart

Meets ASTM B633 SC1, Type III specifications for electroplating of 5um = .0002" thickness. This material is well suited for non-corrosive environments.



152152




Trubolt Wedge Anchors Performance TableUltimate Tension and Shear Values (Lbs/kN) In Concrete*

Anchor Installation Embedment f’c = 2000 PSI (13.8 MPa) f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa) Dia. Torque Depth Anchor Tension Shear Tension Shear Tension Shear In. (mm) Ft. Lbs. (Nm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)1/4 (6.4) 8 (10.8) 1-1/8 (28.6) 1,180 (5.2) 1,400 (6.2) 1,780 (7.9) 1,400 (6.2) 1,900 (8.5) 1,400 (6.2) 1-15/16 (49.2) 2,100 (9.3) 1,680 (7.5) 3,300 (14.7) 1.680 (7.5) 3,300 (14.7) 1,680 (7.5) 2-1/8 (54.0) 2,260 (10.1) 3,300 (14.7) 3,300 (14.7)

3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 1,680 (7.5) 2,320 (10.3) 2,240 (10.0) 2,620 (11.7) 2,840 (12.6) 3,160 (14.1) 3 (76.2) 3,480 (15.5) 4,000 (17.8) 5,940 (26.4) 4,140 (18.4) 6,120 (27.2) 4,500 (20.0) 4 (101.6) 4,800 (21.4) 5,940 (26.4) 6,120 (27.2)

1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 4,660 (20.7) 4.760 (21.2) 5,100 (22.7) 4,760 (21.2) 7,040 (31.3) 7,040 (31.3) 4-1/8 (104.8) 4,660 (20.7) 7,240 (32.2) 9,640 (42.9) 7,240 (32.2) 10,820 (48.1) 8,160 (36.3) 6 (152.4) 5,340 (23.8) 9,640 (42.9) 10,820 (48.1)

5/8 (15.9) 90 (122.0) 2-3/4 (69.9) 6,580 (29.3) 7,121 (31.7) 7,180 (31.9) 7,120 (31.7) 9,720 (43.2) 9,616 (42.8) 5-1/8 (130.2) 6,580 (29.3) 9,600 (42.7) 14,920 (66.4) 11,900(52.9) 16,380(72.9) 12,520(55.7) 7-1/2 (190.5) 7,060 (31.4) 15,020 (66.8) 16,380 (72.9)

3/4 (19.1) 175 (237.3) 3-1/4(82.6) 7,120 (31.7) 10,120 (45.0) 10,840 (48.2) 13,720 (61.0) 13,300 (59.2) 15,980 (71.1) 6-5/8 (168.3) 10,980 (48.8) 20,320 (90.4) 17,700 (78.7) 23,740 (105.6) 20,260 (90.1) 23,740 (105.6) 10 (254.0) 10,980 (48.8) 17,880 (79.5) 23,580 (104.9)

7/8 (22.2) 250 (339.0) 3-3/4 (95.3) 9,520 (42.3) 13,160 (58.5) 14,740 (65.6) 16,580 (73.8) 17,420 (77.5) 19,160 (85.2) 6-1/4 (158.8) 14,660 (65.2) 20,880 (92.9) 20,940 (93.1) 28,800 (128.1) 24,360 (108.4) 28,800 (128.1) 8 (203.2) 14,660 (65.2) 20,940 (93.1) 24,360 (108.4)

1 (25.4) 300 (406.7) 4-1/2 (114.3) 13,940 (62.0) 16,080 (71.5) 20,180 (89.8) 22,820 (101.5) 21,180 (94.2) 24,480 (108.9) 7-3/8 (187.3) 14,600 (64.9) 28,680 (127.6) 23,980 (106.7) 37,940 (168.8) 33,260 (148.0) 38,080 (169.4) 9-1/2 (241.3) 18,700 (83.2) 26,540 (118.1) 33,260 (148.0)

1-1/4 (31.8) 500 (677.9) 5-1/2 (139.7) 18,140 (80.7) 23,280 103.6) 26,380 (117.3) 29,460 (131.0) 33,640 (149.6) 33,780 (150.3) 8 (203.2) 27,340 (121.6) 35,080 (156.0) 43,300 (192.6) 44,260 (196.9) 45,540 (202.6) 50,560 (224.9)

* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

Carbon SteelWithZinc

Plating

or

Carbon SteelWith

Hot-DippedGalvanizing

or

Type 304Stainless

Steel

or

Type 316Stainless

Steel

Lower Flute Of Steel Deck with Lightweight Concrete Lightweight Concrete Fill Anchor Installation Embedment f’c = 3000 PSI (20.7 MPa) f’c = 3000 PSI (20.7 MPa) DIA. Torque Depth Anchor Tension Shear Tension ShearIn. (mm) Ft. Lbs. (Nm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 2,120 (9.4) 3,720 (16.5) 1,900 (8.5) 3,160 (14.1) 3 (76.2) 2,940 (13.1) 4,240 (18.9) 2,840 (12.6) 4,000 (17.8)

1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 3,600 (16.0) 7,040 (31.3) 3,400 (15.1) 5,380 (23.9) 3 (76.2) 4,720 (21.0) 6,620 (29.4) 4,480 (19.9) 6,620 (29.4) 4 (101.6) -- -- 6,920 (30.8) 4,800 (21.4) 6,440 (28.6)

5/8 (15.9) 90 (122.0) 3 (76.2) 6,000 (26.7) 9,240 (41.1) 4,720 (21.0) 5,500 (24.5) 5 (127.0) 5,960 (26.5) 9,280 (41.3) 6,580 (29.3) 9,140 (40.7)

3/4 (19.1) 175 (237.3) 3-1/4 (82.6) 7,160 (31.9) 12,600 (56.0) 5,840 (26.0) 8,880 (39.5) 5-1/4 (133.4) 8,900 (39.6) 15,920 (70.8) 7,040 (31.3) -- --


Carbon Steel With Zinc Plating or

Carbon Steel WithHot-Dipped

Galvanizing orType 304 StainlessSteel or Type 316

Stainless Steel

Trubolt Wedge Anchors Performance TableUltimate Tension and Shear Values (Lbs/kN) In Lightweight Concrete*

Technical Data



153153




Trubolt Wedge Anchors Performance TableRecommended Spacing and Edge Distance Requirements for Tension Loads*

Edge Distance Min. Allowable Min. Allowable Required To Edge Distance At Spacing Required Spacing At Which Anchor Embedment Obtain Max. Which The Load To Obtain Max. The Load Factor Dia. Depth Anchor Working Load Factor Applied = .65 Working Load Applied = .70 In. (mm) In. (mm) Type In. (mm) In. (mm) In. (mm) In. (mm) 1/4 (6.4) 1-1/8 (28.6) 2 (50.8) 1 (25.4) 3-15/16 (100.0) 2 (50.8) 1-15/16 (49.2) 1-15/16 (49.2) 1 (25.4) 3-7/8 (98.4) 1-15/16 (49.2) 2-1/8 (54.0) 1-5/8 (41.3) 13/16 (20.6) 3-3/16 (81.0) 1-5/8 (41.3)

3/8 (9.5) 1-1/2 (38.1) 2-5/8 (66.7) 1-5/16 (33.3) 5-1/4 (133.4) 2-5/8 (66.7) 3 (76.2) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2) 4 (101.6) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2)

1/2 (12.7) 2-1/4 (57.2) 3-15/16 (100.0) 2 (50.8) 7-7/8 (200.0) 3-15/16 (100.0) 4-1/8 (104.8) 3-1/8 (79.4) 1-9/16 (39.7) 6-3/16 (157.2) 3-1/8 (79.4) 6 (152.4) 4-1/2 (114.3) 2-1/4 (57.2) 9 (228.6) 4-1/2 (114.3)

5/8 (15.9) 2-3/4 (69.9) 4-13/16 (122.2) 2-7/16 (61.9) 9-5/8 (244.5) 4-13/16 (122.2) 5-1/8 (130.2) 3-7/8 (98.4) 1-15/16 (49.2) 7-1/16 (195.3) 3-7/8 (98.4) 7-1/2 (190.5) 5-5/8 (142.9) 2-13/16 (71.4) 11-1/4 (285.8) 5-5/8 (142.9)

3/4 (19.1) 3-1/4 (82.6) 5-11/16 (144.5) 2-7/8 (73.0) 11-3/8 (288.9) 5-11/16 (144.5) 6-5/8 (168.3) 5 (127.0) 2-1/2 (63.5) 9-15/16 (252.4) 5 (127.0) 10 (254.0) 7-1/2 (190.5) 3-3/4 (95.3) 15 (381.0) 7-1/2 (190.5)

7/8 (22.2) 3-3/4 (95.3) 6-9/16 (166.7) 3-5/16 (84.1) 13-1/8 (333.4) 6-9/16 (166.7) 6-1/4 (158.8) 6-1/4 (158.8) 3-1/8 (79.4) 12-1/2 (317.5) 6-1/4 (158.8) 8 (203.2) 6 (152.4) 3 (76.2) 12 (304.8) 6 (152.4)

1 (25.4) 4-1/2 (114.3) 7-7/8 (200.0) 3-15/16 (100.0) 15-3/4 (400.1) 7-7/8 (200.0) 7-3/8 (187.3) 7-3/8 (187.3) 3-11/16 (93.7) 14-3/4 (374.7) 7-3/8 (187.3) 9-1/2 (241.3) 7-1/8 (181.0) 3-9/16 (90.5) 14-1/4 (362.0) 7-1/8 (181.0)

1-1/4 (31.8) 5-1/2 (139.7) 9-5/8 (244.5) 4-13/16 (122.2) 19-1/4 (489.0) 9-5/8 (244.5) 8 (203.2) 8 (203.2) 4 (101.6) 16 (406.4) 8 (203.2)

* Spacing and edge distances shall be divided by 0.75 when anchors are placed in structural lightweight concrete. Linear interpolation may be used for intermediate spacing and edge distances.

Carbon Steel WithZinc Plating

or

Carbon Steel WithHot-DippedGalvanizing

or

Type 304 StainlessSteel

or

Type 316Stainless Steel

Edge Distance Min. Edge Min. Edge Distance Spacing Min. Allowable Required To Distance At Which At Which The Required to Spacing Between Anchor Embedment Obtain Max. The Load Factor Load Factor Obtain Max. Anchors In. (mm) Dia. Depth Anchor Working Load Applied = .60 Applied = .20 Working Load Load Factor In. (mm) In. (mm) Type In. (mm) In. (mm) In. (mm) In. (mm) Applied = .40 1/4 (6.4) 1-1/8 (28.6) 2 (50.8) 1-5/16 (33.3) -- -- 3-15/16 (100.0) 2 (50.8) 1-15/16 (49.2) 1-15/16 (49.2) 1 (25.4) -- -- 3-7/8 (98.4) 1-15/16 (49.2)

3/8 (9.5) 1-1/2 (38.1) 2-5/8 (66.7) 1-3/4 (44.5) -- -- 5-1/4 (133.4) 2-5/8 (66.7) 3 (76.2) 3-3/4 (95.3) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2)

1/2 (12.7) 2-1/4 (57.2) 3-15/16 (100.0) 2-9/16 (65.1) -- -- 7-7/8 (200.0) 3-15/16 (100.0) 4-1/8 (104.8) 5-3/16 (131.8) 3-1/8 (79.4) 1-9/16 (39.7) 6-3/16 (157.2) 3-1/8 (79.4)

5/8 (15.9) 2-3/4 (69.9) 4-13/16 (122.2) 3-1/8 (79.4) -- -- 9-5/8 (244.5) 4-13/16 (122.2) 5-1/8 (130.2) 6-7/16 (163.5) 3-7/8 (98.4) 1-15/16 (49.2) 7-11/16 (195.3) 3-7/8 (98.4)

3/4 (19.1) 3-1/4 (82.6) 5-11/16 (144.5) 3-3/4 (95.3) -- -- 11-3/8 (288.9) 5-11/16 (144.5) 6-5/8 (168.3) 6-5/16 (160.3) 5 (127.0) 2-1/2 (63.5) 9-15/16 (252.4) 5 (127.0)

7/8 (22.2) 3-3/4 (95.3) 6-9/16 (166.7) 4-5/16 (109.5) -- -- 13-1/8 (333.4) 6-9/16 (166.7) 6-1/4 (158.8) 8-1/2 (215.9) 6-1/4 (158.8) 3-1/8 (79.4) 12-1/2 (317.5) 6-1/4 (158.8)

1 (25.4) 4-1/4 (108.0) 7-7/8 (200.0) 5-1/8 (130.2) -- -- 15-3/4 (400.1) 7-7/8 (200.0) 7-3/8 (187.3) 10-1/16 (255.6) 7-3/8 (187.3) 3-11/16 (93.7) 14-3/4 (374.7) 7-3/8 (187.3)

1-1/4 (31.8) 5-1/2 (139.7) 9-5/8 (244.5) 6-1/4 (158.8) -- -- 19-1/4 (489.0) 9-5/8 (244.5) 8 (203.2) 11-7/16 (290.5) 8 (203.2) 4 (101.6) 16 (406.4) 8 (203.2)


Trubolt Wedge Anchors Performance TableRecommended Spacing And Edge Distance Requirements For Shear Loads*

Carbon Steel With Zinc Plating

or

Carbon Steel WithHot-DippedGalvanizing

orType 304 Stainless

Steel

or

Type 316Stainless Steel

Combined Shear and Tension Loading for Trubolt AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation: (Ps/Pt)5/3 + (Vs/Vt)5/3 ≤ 1


Technical Data


154154




CODE COMPLIANTCODE COMPLIANTCONCRETE ANCHORSCONCRETE ANCHORS

155155




Multi-Set II® Drop-In AnchorsInternally Threaded Heavy Duty Anchoring Systems

To set anchor below surface: Drill hole deeper than anchor length. Thread bolt into anchor. Hammer anchor into hole until bolt head is at desired depth. Remove bolt and set anchor with setting tool.

Installation Steps

1 setting tool per master carton except for RX-38 which is 1 per box.

Description/suggested specificationsDrop-In, Shell-Type AnchorsSpecified for anchorage into concreteDrop-In, shell-type anchors feature an internally threaded, all-steel shell with expansion cone insert and flush embedment lip. Anchors are manufactured from plated carbon steel, 18-8 stainless steel and 316 stainless steel.

Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 specifications.

Anchors should be tested to ASTM E488 criteria and listed by ICBO and SBCCI. Anchors should also be listed by the following agencies as required by the local building code: UL, FM, City of Los Angeles, Metro Dade, California State Fire Marshal and Cal Trans.

Approvals/listings• Meets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group VIII, Type 1• Underwriters Laboratories• Factory Mutual• ICBO Evaluation Service, Inc. – #ER-1372• City of Los Angeles – #RR2748• SBCCI Compliance Report – #9570• California State Fire Marshal• Cal Trans

To set flush with surface:• Drill hole the same diameter as

anchor being used to any depth exceeding minimum embedment. Clean hole.

• Drive anchor flush with surface of concrete.

• Expand anchor with setting tool provided. Anchor is properly expanded when shoulder of setting tool is flush with top of anchor.

MULTI-SET IIMULTI-SET II® ® DROP IN ANCHORSDROP IN ANCHORS

156156




Sizes

Combined Shear and Tension Loading—for Multi-Set AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation:

(Ps/Pt)5/3 + (Vs/Vt)5/3 ≤ 1


Multi-Set II Drop-In Anchors Selection Chart


Embedment Corrosion Drop-In Bolt Size Drill Bit Thread Min. Hole Qty/Wt Qty/Wt User Type/ Base Resistance Anchor Threads Size Depth Depth Per Box Per Master Application Material Level Type Per Inch In. (mm) In. (mm) In. (mm) lbs. Ctn lbs. HVAC/Fire Sprinkler Poured Low RM 1/4" - 20 3/8" (9.5) 3/8" (9.5) 1" (25.4) 100/ 2.6 1000/28 Plumber (Pipe-fitter) in place 3/8" - 16 1/2" (12.7) 1/2" (12.7) 1-5/8" (41.3) 50/ 3.4 500/36 concrete/ 1/2" - 13 5/8" (15.9) 3/4" (19.1) 2" (50.8) 50/ 5.8 400/ 49 lightweight 5/8" - 11 7/8" (22.2) 1" (25.4) 2-1/2" (63.5) 25/ 7.8 125/ 41 fill deck 3/4" - 10 1" (25.4) 1-1/4" (31.8) 3-3/16" (81.0) 25/ 11.9 100/ 49

Hollow- Low RX 3/8" - 16 1/2" (12.7) 1/2" (12.7) 3/4" (19.1) 100/ 3.5 1000/ 36 core pre-cast or Post- tension

Solid Medium SRM 1/4" - 20 3/8" (9.5) 3/8" (9.5) 1" (25.4) 100/2.7 1000/28 concrete 18-8 S.S. 3/8" - 16 1/2" (12.7) 1/2" (12.7) 1-5/8" (41.3) 50/3.4 500/36 1/2" - 13 5/8" (15.9) 3/4" (19.1) 2" (50.8) 50/6.0 400/50 5/8" - 11 7/8" (22.2) 1" (25.4) 2-1/2" (63.5) 25/18.0 125/42 3/4" - 10 1" (25.4) 1-1/4" (31.8) 3-3/16" (81.0) 25/12.0 100/50

Solid High SSRM 3/8" - 16 1/2" (12.7) 1/2" (12.7) 1-5/8" (41.3) 50/ 3.4 500/ 36 concrete 316 S.S. 1/2" - 13 5/8" (15.9) 3/4" (19.1) 2" (50.8) 50/ 6.0 400/ 50

Concrete Contractor, Solid Low CL-Coil 1/2" - 6 5/8" (15.9) 3/4" (19.1) 2" (50.8) 50/ 5.7 400/ 47 General Contractor, Highway concrete Threaded 3/4" - 4.5 1" (25.4) 1-1/4" (31.8) 3-3/16" (81.0) 25/ 11.9 100/ 49

Concrete Cutting/ Solid Low RL 1/4" - 20 3/8" (9.5) 3/8" (9.5) 1" (25.4) 100/ 2.6 1000/ 28 Sawing Contractor/ concrete (w/o lip) 3/8" - 16 1/2" (12.7) 1/2" (12.7) 1-5/8" (41.3) 50/ 3.4 500/ 36 Misc. Metal 1/2" - 13 5/8" (15.9) 3/4" (19.1) 2" (50.8) 50/ 5.8 400/ 49 5/8" - 11 7/8" (22.2) 1" (25.4) 2-1/2" (63.5) 25/ 7.8 125/ 41 3/4" - 10 1" (25.4) 1-1/4" (31.8) 3-3/16" (81.0) 25/ 11.9 100/ 49


157157




RM or RL-Carbonor

SRM-18-8 S.S. orSSRM-316 S.S.

Minimum Bolt Anchor Embedment f’c = 2000 PSI (13.8 MPa) f’c = 4000 PSI (26.6 MPa) f’c = 6000 PSI (41.4 MPa) Dia. Dia. Depth Anchor Tension Shear Tension Shear Tension ShearIn. (mm) In. (mm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) 1/4" (6.4) 3/8 (9.5) 1 (25.4) 1,680 (7.5) 1,080 (4.8) 2,360 (10.5) 1,200 (5.3) 2,980 (13.3) 1,300 (5.8) 3/8 (9.5) 1/2 (12.7) 1-5/8 (41.3) 2,980 (13.3) 3,160 (14.1) 3,800 (16.9) 2,500 (11.1) 6,240 (27.8) 1,860 (8.3) 1/2 (12.7) 1/2 (12.7) 2 (50.8) 2-1/4 (57.2) 3,300 (14.7) 4,580 (20.4) 5,840 (26.0) 3,500 (15.6) 8,300 (36.9) 2,400 (10.7) 5/8 (15.9) 5/8 (15.9) 2-1/2 (63.5) 5,500 (24.5) 7,440 (33.1) 8,640 (38.4) 5,540 (24.6) 11,020 (49.0) 3,640 (16.2) 3/4 (19.1) 3/4 (19.1) 3-3/16 (81.0) 8,280 (36.8) 10,480 (46.6) 9,480 (42.2) 7,680 (34.2) 12,260 (54.5) 4,860 (21.6)


RM or RL-Carbonor

SRM-18-8 S.S.or

SSRM-316 S.S.

Ultimate Shear and Tension Values (Lbs/kN) In Concrete*

Lower Flute Of Steel Deck with Minimum Lightweight Concrete Lightweight Concrete Fill Bolt Anchor Embedment f’c = 3000 PSI (20.7 MPa) f’c = 3000 PSI (20.7 MPa) Dia. Dia. Depth Anchor Tension Shear Tension ShearIn. (mm) In. (mm) In. (mm) Type Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 1/2 (12.7) 1-5/8 (39.7) 3,860 (17.2) 4,420 (19.6) 3,340 (14.9) 4,420 (19.6)1/2 (12.7) 5/8 (15.9) 2 (50.8) 4,080 (18.1) 5,640 (25.1) 3,200 (14.2) 4,940 (22.0)5/8 (15.9) 7/8 (22.2) 2-1/2 (63.5) 6,280 (27.9) 10,440 (46.4) 5,960 (26.5) 5,840 (26.0)3/4 (19.1) 1 (25.4) 3-3/16 (81.0) 11,000 (48.9) 15,780 (70.2) 8,180 (36.4) 9,120 (40.6)


Ultimate Shear and Tension Values (Lbs/kN) In Lightweight Concrete*

Technical Data

RM or RL-Carbonor

SRM-18-8 S.S. orSSRM-316 S.S.

Min. Allowable Min. Edge Spacing Between Edge Distance Distance At Which Spacing Anchors Load Required To Load Factor Applied Required to Factor Applied Bolt Anchor Embedment Obtain Max. = .80 For Tension Obtain Max. = .80 For Tension Dia. Dia. Depth Anchor Working Load = .70 For Shear Working Load = .70 For Shear In. (mm) In. (mm) In. (mm) Type In. (mm) In. (mm) In. (mm) In. (mm) 1/4 (6.4) 3/8 (9.5) 1 (25.4) 1-3/4 (44.5) 7/8 (22.2) 3-1/2 (88.9) 1-3/4 (44.5) 3/8 (9.5) 1/2 (12.7) 1-5/8 (39.7) 2-7/8 (73.0) 1-7/16 (36.5) 5-11/16 (144.5) 2-7/8 (73.0) 1/2 (12.7) 5/8 (15.9) 2 (50.8) 3-1/2 (88.9) 1-3/4 (44.5) 7 (177.8) 3-1/2 (88.9) 5/8 (15.9) 7/8 (22.2) 2-1/2 (63.5) 4-3/8 (111.1) 2-3/16 (55.6) 8-3/4 (222.3) 4-3/8 (111.1) 3/4 (19.1) 1 (25.4) 3-3/16 (81.0) 5-5/8 (142.9) 2-13/16 (71.4) 11-3/8 (284.2) 5-5/8 (142.9)


Recommended Spacing And Edge Distance Requirements*

Anchor f’c = 3000 PSI (20.7 MPa) f’c = 3000 PSI (20.7 MPa) Size Dia. Embedment Tension Shear T ension ShearIn. (mm) In. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 1/2 (12.7) 3/4 (19.1) 1,987 (8.8) 2,903 (12.9) 1,908 (8.5) 2,525 (11.2)

* The tabulated values are for RX-38 anchors installed at minimum of 12-diameters on center and minimum edge distance of six-diameters for 100% anchor efficiency. Spacing and edge distance may be reduced to six-diameters spacing and three-diameter edge distance provided the values are reduced 50%. Linear INterpolation may be used for intermediate spacings and edge margins.


Ultimate Shear and Tension Values (Lbs/kN) For RX-38 (3/4 Embedment)*



158158




A7 Acrylic AdhesiveEasy To Use A7 saves you time and money

Curing Times and Dispensing Speeds Full Temperature Working Curing Dispensing1 (F °/C°) T ime Time Speed 100˚ / 38˚ 5 Minutes 25 Minutes 16 Seconds 80˚ / 27˚ 5.5 Minutes 30 Minutes 16 Seconds 60˚ / 16˚ 7 Minutes 35 Minutes 26Seconds 40˚ / 4˚ 15 Minutes 75 Minutes 47Seconds 20˚ / -7˚ 35 Minutes 6 Hours 1 Min. 21 Sec. 0˚ / -18˚ 4 Hours 24 Hours 2 Minutes

1 Dispensing rates for A7-28 cartridge using A200 pneumatic tool. Cartridge temperature = temperature shown

Part Description Box Qt.

Fits Hilti® P2000 Dispensing Tools 8 Fluid Ounce Cartridge A7 12

Mixing Nozzle for A7-8 Cartridge 24

Hand Dispenser for A7-8 Cartridge 1

Epcon A7 8 oz. Ordering Information

Part Description Box Qty

28 Fluid Ounce Cartridge A7 8

Mixing Nozzle for A7-28 Oz. Cartridge 24 A50 nozzles fit into 3/8" holes & tip can be broken off to increase flow for larger holes

Hand Dispenser for A7-28 Cartridge 1 Largest hand dispensable cartridge— still easy to dispense

Pneumatic Dispenser for A7-28 Cartridge 1

Epcon A7 28 oz. Ordering Information

Description/suggested specifications*Fast Dispensing, Fast Curing Acrylic AdhesiveThe acrylic resin and hardening agent are completely mixed as they are simultaneously dispensed from the dual cartridge through a static mixing nozzle, directly into the anchor hole. A7 can be used with threaded rod or rebar.

Advantages• All weather formula, down to 0°F and below• No drip, no sag, easy clean up• Fast & easy dispensing, 28-oz. cartridge in 16 seconds• Fast curing time, 35 minutes at 60°F• Rods are easier to insert into the hole with A7 compared

with other adhesives• Works in damp holes and underwater applications• One formula for both hollow and solid base materials

Approvals/listingsASTM Type IV, Grade 3, Class A, B, C (exceptions - A7 gels faster than ASTM requirements and does not contain any epoxy)ICBO Evaluation Service, Inc. – #ER-5560City of Los Angeles – RR#25379DOT Approvals

2. When starting new cartridge or nozzle, dispense and discard enough adhesive until uniform dark grey color is achieved. Insert the nozzle into the bottom of the hole and fill to 1/2 the hole depth.

1. Drill proper size hole. Clean out hole from bottom with forced air. Complete hole preparation with use of a brush and repeat cleaning with forced air (leave no dust or slurry).

Installation Steps

3. Insert the selected rod slowly by hand into the bottom of the hole with a slow twisting motion. This insures the adhesive fills voids and crevices uniformly.

4. See A7 Cure Time Charts for set-up time. After the recommended cure time is met, install and tighten fixture into place.

Solid Base Material

Hilti® P2000 is a registered trademark of Hilti, Corp.

A7 ACRYLIC ADHESIVEA7 ACRYLIC ADHESIVE

159159




Hole Embedment Depth In Inches (mm) Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15Rebar Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (381. 0)# 3 7/16 187.8 93.9 62.6 46.9 37.6 31.3 26.8 23.5 20.9 18.8 17.1 15.6 14.4 13.4 12.5# 4 5/8 105.7 52.9 35.2 26.4 21.1 17.6 15.1 13.2 11.7 10.6 9.6 8.8 8.1 7.6 7.0# 5 3/4 81.1 40.5 27.0 20.3 16.2 13.5 11.6 10.1 9.0 8.1 7.4 6.8 6.2 5.8 5.4# 6 7/8 65.5 32.7 21.8 16.4 13.1 10.9 9.4 8.2 7.3 6.5 6.0 5.5 5.0 4.7 4.4# 7 1 60.5 30.2 20.2 15.1 12.1 10.1 8.6 7.6 6.7 6.0 5.5 5.0 4.7 4.3 4.0# 8 1-1/8 50.2 25.1 16.7 12.6 10.0 8.4 7.2 6.3 5.6 5.0 4.6 4.2 3.9 3.6 3.3# 9 1-1/4 29.1 14.6 9.7 7.3 5.8 4.9 4.2 3.6 3.2 2.9 2.6 2.4 2.2 2.1 1.9# 10 1-1/2 23.8 11.9 7.9 6.0 4.8 4.0 3.4 3.0 2.6 2.4 2.2 2.0 1.8 1.7 1.6# 11 1-3/4 14.6 7.3 4.9 3.6 2.9 2.4 2.1 1.8 1.6 1.5 1.3 1.2 1.1 1.0 1.0

* Be sure to use the correct multiplier. Approximate number of anchors for 28 ounce cartridge: Multiply the number of 8 Oz. anchors by 3.5.

Epcon A7 Estimating Table For 8 Fluid Oz. CartridgeNumber Of Anchoring Installations Per Cartridge* Using Reinforcing Bar With A7 Adhesive In Solid Concrete

A7 Acrylic AdhesiveEasy To Use A7 saves you time and money

Technical Data

Embedment Depth In Inches (mm) Rod Hole Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 In. (mm) Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (3 81.0)

1/4 (6.4) 5/16 259.5 129.7 86.5 64.9 51.9 43.2 37.1 32.4 28.8 25.9 23.6 21.6 20.0 18.5 17.3

3/8 (9.5) 7/16 150.2 75.1 50.1 37.6 30.0 25.0 21.5 18.8 16.7 15.0 13.7 12.5 11.6 10.7 10.0

1/2 (12.7) 9/16 108.1 54.1 36.0 27.0 21.6 18.0 15.4 13.5 12.0 10.8 9.8 9.0 8.3 7.7 7.2

5/8 (15.9) 11/16 77.6 38.8 25.9 19.4 15.5 12.9 11.1 9.7 8.6 7.8 7.1 6.5 6.0 5.5 5.2 3/4 55.4 27.7 18.4 13.8 11.1 9.2 7.9 6.9 6.1 5.5 5.0 4.6 4.3 4.0 3.7

3/4 (19.1) 13/16 54.7 27.3 18.2 13.7 10.9 9.1 7.8 6.8 6.1 5.5 5.0 4.6 4.2 3.9 3.6 7/8 43.6 21.8 14.6 10.9 8.8 7.3 6.3 5.5 4.9 4.4 4.0 3.6 3.4 3.1 2.9

7/8 (22.2) 15/16 52.5 26.2 17.5 13.1 10.5 8.7 7.5 6.6 5.8 5.2 4.8 4.4 4.0 3.7 3.5 1 36.4 18.2 12.2 9.1 7.3 6.1 5.2 4.5 4.0 3.6 3.3 3.0 2.8 2.6 2.4

1 (25.4) 1 -1/16 44.9 22.4 15.0 11.2 9.0 7.5 6.4 5.6 5.0 4.5 4.1 3.7 3.5 3.2 3.0 1 -1/8 34.4 17.2 12.0 8.6 7.5 6.0 5.0 4.3 3.7 3.3 3.0 2.7 2.5 2.3 2.1

1-1/4 (31.8) 1 -5/16 28.7 14.4 9.6 7.2 5.7 4.8 4.1 3.6 3.2 2.9 2.6 2.4 2.2 2.1 1.9 1 -3/8 22.4 11.2 7.6 5.6 4.5 3.8 3.2 2.8 2.5 2.3 2.1 1.9 1.7 1.6 1.5

• The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.• Approximate the number of anchors per 28 Oz. cartridge: Multiply the number of 8Oz. anchors by 3.53.

Epcon A7 Estimating Table For 8 Fluid Oz. CartridgeNumber Of Anchoring Installations Per Cartridge* Using Threaded Rod With A7 Adhesive In Solid Concrete


THREADED RODTHREADED ROD

REBARREBAR

160160




A500 PLASTIC DISPENSERAttaches directly to cartridge allowing for easyhand dispensing.No extra tools are required.

A501 CAULKING GUN ADAPTER Allows cartridge to work with moststandard caulking guns (caulkinggun supplied by contractor).

3. Turn lever in order to dispense adhesive.

Simple Assembly and Dispensing

2. Thread nozzle onto cartridge.

1. Twist-lock dispenser onto cartridge.

3. Place assembly in caulking gun and dispense adhesive.

Simple Assembly and Dispensing

2. Thread nozzle onto cartridge.

1. Push adapter tightly against back of cartridge.

Part Description Box Qty

5 Fluid Ounce Cartridge A7 12

Reusable Plastic Dispenser 12

Convenient Dispensing Kit Packaged in a Plastic Bag with (1) A500 Plastic Dispenser 8 Assembled on (1) A7-5 Cartridge and (1) A24 Nozzle

Mixing Nozzle 24

Reusable Caulking 12 Gun Adapter

Convenient Dispensing Kit Packaged in a Plastic Bag with (1) A501 Caulking Gun Adapter 8 Assembled on (1) A7-5 Cartridge and (1) A24 Nozzle

Epcon A7 5 oz. Ordering InformationA7 Acrylic AdhesiveEasy To Use A7 Saves You Time and Money


161161




Hole Embedment Depth In Inches (mm) Dia. 2 4 6 8Rebar Inches (50.8) (101.6) (152.4) (203.2)# 3 7/16 60 30 20 15# 4 5/8 34 17 11 8# 5 3/4 26 13 9 6# 6 7/8 21 10 7 5# 7 1 19 10 6 5# 8 1-1/8 16 8 5 4

Hole Embedment Depth In Inches (mm)Rod Dia. 2 4 6 8In (mm) Inches (50.8) (101.6) (152.4) (203.2)3/8 (9.5) 7/16 48 24 16 12

1/2 (12.7) 9/16 35 17 12 9

5/8 (15.9) 11/16 25 12 8 6 3/4 18 9 6 4

3/4 (19.1) 13/16 18 9 6 4 7/8 14 7 5 4

7/8 (22.2) 15/16 17 8 6 4 1 12 6 4 3

1 (25.4) 1-1/16 14 7 5 4 1-1/8 10 5 3 2

* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bits, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.

2000 PSI (13.8 MPa) CONCRETE 4000 PSI (27.6 MPa) CONCRETEThreaded Setting Embedment Ultimate Ultimate Ultimate UltimateRod Dia. Torque In Concrete Tension Shear Tension ShearIn. (mm) Ft. Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 13 - 18 (17-24) 3-3/8 (85.7) 5,852 (26.0) 5,220 (23.2) 10,977 (48.8) 5,220 (23.2) 4-1/2 (114.3) 7,729 (34.4) 5,220 (23.2) 11,661 (51.9) 5,220 (23.2)

1/2 (12.7) 22 - 25 (29-33) 4-1/2 (114.3) 10,798 (48.0) 8,029 (35.7) 17,162 (76.3) 8,029 (35.7) 6 (152.4) 14,210 (63.2) 8,029 (35.7) 17,372 (77.3) 8,029 (35.7)

5/8 (15.9) 55 - 80 (74-108) 5-5/8 (142.9) 16,417 (73.0) 15,967 (71.0) 26,504 (117.9) 15,967 (71.0) 7-1/2 (190.5) 18,747 (83.4) 15,967 (71.0) 29,381 (130.7) 15,967 (71.0)

3/4 (19.1) 106 - 160 (143-216) 6-3/4 (171.5) 18,618 (82.8) 20,126 (89.5) 29,727 (132.2) 20,126 (89.5)

9 (228.6) 23,934 (106.5) 20,126 (89.5) 37,728 (167.8) 20,126 (89.5)

7/8 (22.2) 185 - 250 (250-338) 7-7/8 (200.0) -- -- 29,866 (132.9) 44,915 (199.8) 29,866 (132.9) 10-1/2 (266.7) 36,881 (164.1) 29,866 (132.9) 48,321 (215.0) 29,866 (132.9)

1 (25.4) 276 - 330 (374-447) 9 (228.6) 32,215 (143.3) 37,538 (167.0) 48,209 (214.5) 37,538 (167.0) 12 (304.8) 46,064(143.3) 37,538(167.0) 63,950(284.5) 37,538(167.0)

1-1/4 (31.8) 370 - 660 (501-894) 11-1/4 (285.8) 45,962 (204.5) 58,412 (259.8) 56,715 (252.3) 58,412 (259.8) 15 (381.0) 62,208 (276.7) 58,412 (259.8) 84,385(375.4) 58,412 (259.8)

1 Allowable working loads for the single installations under static loading should not exceed 25% capacity or the allowable load of the anchor rod.

2 Ultimate load values in 2000 and 4000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in the Embedment in Concrete column.Performance values are based on the use of high strength threaded rod (ASTM A193 Gr. B7). The use of lower strength rods will result in lower ultimate tension and shear loads.

Epcon A7 Acrylic Adhesive Performance TableAverage Ultimate Tension and Shear Loads1,2 for Threaded Rod Installed in Solid Concrete

Allowable Tension Load Based On Adhesive Bond Strength Allowable Tension Load Based On Steel StrengthThreaded Minimum 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) ASTM A307 ASTM A193Gr. Rod Dia. Embedment Concrete Concrete (SAE 1018) B7 (SAE 4140) AISI 304 SSIn. (mm) Depth In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 3-3/8 (85.7) 1,460 (6.5) 2,740 (12.2) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8) 4-1/2 (114.3) 1,930 (8.6) 2,915 (13.0) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8)

1/2 (12.7) 4-1/2 (114.3) 2,700 (12.0) 4,290 (19.1) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8) 6 (152.4) 3,550 (15.8) 4,340 (19.3) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8)

5/8 (15.9) 5-5/8 (142.9) 4,100 (18.3) 6,625 (29.5) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0) 7-1/2 (190.5) 4,685 (20.8) 7,345 (32.7) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0)

3/4 (19.1) 6-3/4 (171.5) 4,655 (20.7) 7,430 (33.1) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1) 9 (228.6) 5,980 (26.6) 9,430 (42.0) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1)

7/8 (22.2) 7-7/8 (200.0) -- -- 11,230 (49.9) 11,600 (51.6) 25,510 (113.5) 20,835 (92.7) 10-1/2 (266.7) 9,220 (41.0) 12,080 (53.7) 11,600 (51.6) 25,510 (113.5) 20,834 (92.7)

1 (25.4) 9 (228.6) 8,050 (35.8) 12,050 (53.6) 15,180 (67.5) 31,620 (140.7) 26,560 (118.1) 12 (304.8) 11,515 (51.2) 15,985 (71.1) 15,180 (67.5) 31,620 (140.7) 26,560 (118.1)

1-1/4 (31.8) 11-1/4 (285.8) 11,490 (51.1) 14,175 (63.1) 23,800 (105.9) 49,580 (220.6) 34,670 (154.2) 15 (381.0) 15,550 (69.2) 21,095 (93.8) 23,800 (105.9) 49,580 (220.6) 34,670 (154.2)

1 Use lower value of either bond or steel strength for allowable tensile load. 2 Allowable loads taken from ICBO Evaluation Report #5560.

Epcon A7 Acrylic Adhesive Performance TableAllowable Tension Loads 1,2 for Threaded Rod Installed in Solid Concrete

Technical DataEpcon A7 5 Fluid Ounce Cartridge Estimating Tables - Number of Anchoring Installations per

Cartridge* Using Reinforcing Bar and Threaded Rod with A7 Adhesive in Solid Concrete


162162




Allowable Shear Load Minimum Based On Concrete Strength Allowable Shear Load Based On Steel StrengthThreaded Embedment 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) ASTM A307 ASTM A193 GR. B7 Rod Dia. Depth Concrete Concrete (SAE 1018) (SAE 4140) AISI 304 SSIn. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 3-3/8 (85.7) 1,305 (5.8) 1,305 (5.8) 1,040 (4.6) 2,170 (9.7) 1,995 (8.9)1/2 (12.7) 4-1/2 (114.3) 2,005 (8.9) 2,005 (8.9) 1,870 (8.3) 3,895 (17.3) 3,585 (15.9)5/8 (15.9) 5-5/8 (142.9) 3,990 (17.8) 3,990 (17.8) 2,940 (13.1) 6,125 (27.2) 5,635 (25.1)3/4 (19.1) 6-3/4 (171.5) 5,030 (22.4) 5,030 (22.4) 4,250 (18.9) 8,855 (39.4) 7,440 (33.1)7/8 (22.2) 7-7/8 (200.0) 7,465 (33.2) 7,465 (33.2) 5,800 (25.8) 12,760 (56.8) 10,730 (47.7)1 (25.4) 9 (228.6) 9,385 (41.7) 9,385 (41.7) 7,590 (33.8) 15,810 (70.3) 13,285 (59.1)1-1/4 (31.8) 11-1/4 (285.8) 14,600 (64.9) 14,600 (64.9) 11,900 (52.9) 24,790 (100.3) 18,840 (83.8)

1 Use lower value of either concrete or steel strength for allowable shear load.2 Allowable loads taken from ICBO Evaluation Report #5560.

Allowable Shear Loads 1,2 for Threaded Rod Installed in Solid Concrete

Threaded Drill Hole Embedment Ultimate UltimateRod Dia. Diameter Depth Anchor Tension ShearIn. (mm) In. (mm) In. (mm) Location Lbs. (kN) Lbs. (kN)1/2 (12.7) 5/8 (15.9) 4-1/4 (108.0) GROUTED CELL 5,170 (23.0) 8,500 (37.8)

5/8 (15.9) 3/4 (19.1) 5 (127.0) GROUTED CELL 6,320 (28.1) 10,850 (48.3)

3/4 (19.1) 7/8 (22.2) 6-5/8 (168.3) GROUTED CELL 10,910 (48.5) 17,075 (76.0)

Allowable working loads for the single installations should not exceed 25% (an industry standard) capacity or the allowable load of the anchor rod. Loads based upon testing with ASTM A193, Grade B7 rods.

Average Ultimate Tension And Shear Loads 1 For Threaded RodInstalled In Grout Filled Concrete Block

Threaded Drill Hole Embedment Ultimate UltimateRod Dia. Diameter Depth Anchor Tension ShearIn. (mm) In. (mm) In. (mm) Location Lbs. (kN) Lbs. (kN)1/4 (6.4) 3/8 (9.5) 3-1/2 (88.9) CENTER OF 2,130 (9.5) 1,165 (5.2) 6 (152.4) BRICK FACE 3,575 (15.9) 1,550 (6.9)

3/8 (9.5) 1/2 (12.7) 3-1/2 (88.9) CENTER OF 2,130 (9.5) 4,150 (18.5) 6 (152.4) BRICK FACE 8,875 (39.5) 6,950 (30.9)

1/2 (12.7) 5/8 (15.9) 3-1/2 (88.9) CENTER OF 2,130 (9.5) 3,090 (13.7) 6 (152.4) BRICK FACE 12,155 (54.1) 7,910 (35.2)

1 Allowable working loads for the single installations should not exceed 25% (an industry standard) capacity or the allowable load of the anchor rod. Loads based upon testing with ASTM A193, Grade B7 rods.

2 Void between brick widths was grouted solid; therefore the use of screens was not necessary.

Average Ultimate Tension And Shear Loads1 For Threaded RodInstalled In Grouted2 Brick Masonry Constructed Of Solid Red Brick Units

Technical Data

Epcon A7 Acrylic


THREADED RODTHREADED ROD

163163




Ultimate Tensile And Yield Strength 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) Grade 60 RebarReinforcing Embedment Concrete Concrete Minimum Yield Minimum UltimateBar Dia. In Concrete Ultimate Tension Ultimate Tension Strength Tensile StrengthIn. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)# 3 (9.5) 3-3/8 (85.7) 6,180 (27.5) 8,324 (37.0) 6,600 (29.4) 9,900 (44.0) 4-1/2 (114.3) 7,560 (33.6) 11,418 (50.8) 6,600 (29.4) 9,900 (44.0)

# 4 (12.7) 4-1/2 (114.3) 9,949 (44.3) 16,657 (74.1) 12,000 (53.4) 18,000 (80.1) 6 (152.4) 15,038 (66.9) 17,828 (79.3) 12,000 (53.4) 18,000 (80.1)

# 5 (15.9) 5-5/8 (142.9) 14,012 (62.3) 20,896 (93.0) 18,600 (82.7) 27,900 (124.1) 7-1/2 (190.5) 16,718 (74.4) 26,072 (116.0) 18,600 (82.7) 27,900 (124.1)

# 6 (19.1) 6-3/4 (171.5) 21,247 (94.5) 26,691 (118.7) 26,400 (117.4) 39,600 (176.2) 9 (228.6) 33,325 (148.2) 37,425 (166.5) 26,400 (117.4) 39,600 (176.2)

# 7 (22.2) 7-7/8 (200.0) -- -- 40,374 (179.6) 36,000 (160.1) 54,000 (240.2) 10-1/2 (266.7) 38,975 (173.4) 46,050 (204.8) 36,000 (160.1) 54,000 (240.2)

# 8 (25.4) 9 (228.6) 35,600 (158.4) 47,311 (210.5) 47,400 (210.9) 71,100 (316.3) 12 (304.8) 41,010 (182.4) 66,140 (294.2) 47,400 (210.9) 71,100 (316.3)

# 9 (28.6) 10-1/8 (257.2) -- -- 57,221 (254.5) 60,000 (266.9) 90,000 (400.4) 13-1/2 (342.9) -- -- 79,966 (355.7) 60,000 (266.9) 90,000 (400.4)

# 10 (31.8) 11-1/4 (285.8) 49,045 (218.2) 73,091 (325.1) 76,200 (339.0) 114,300 (508.5) 15 (381.0) 69,079 (307.3) 83,295 (370.5) 76,200 (339.0) 114,300 (508.5)

# 11 (34.9) 12-3/8 (314.3) 63,397 (282.0) 75,047 (333.8) 93,600 (416.4) 140,400 (624.6) 16-1/2 (419.1) 81,707 (363.5) 91,989 (409.2) 93,600 (416.4) 140,400 (624.6)

1 Allowable working loads for the single installations under static loading should not exceed 25% capacity or the allowable load of the anchor rod.

2 Ultimate load values in 2000 and 4000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in the Embedment in Concrete column. Performance values are based on the use of minimum Grade 60 reinforcing bar. The use of lower strength rods will result in lower ultimate tension loads.

Average Ultimate Tension Loads1,2 for Reinforcing Bar Installed in Solid Concrete

Critical Interpolated Interpolated MinimumAnchor Embedment Edge Distance Edge Distance Edge Distance Edge DistanceDiameter Depth In. (mm) In. (mm) In. (mm) In. (mm)In. (mm) In. (mm) (100% Load Capacity) (80% Load Capacity) (50% Load Capacity) (10% Load Capacity)3/8 (9.5) 3-3/8 (85.7) 4-3/16 (106.4) 3-7/16 (87.3) 2-5/16 (58.7) 13/16 (20.6)

1/2 (12.7) 4-1/2 (114.3) 5-5/8 (142.9) 4-5/8 (117.5) 3-1/8 (79.4) 1-1/8 (28.6)

5/8 (15.9) 5-5/8 (142.9) 7 (177.8) 5-3/4 (146.1) 3-1/8 (79.4) 1-3/8 (34.9)

3/4 (19.1) 6-3/4 (171.5) 8-7/16 (214.2) 6-15/16 (176.2) 4-5/8 (117.5) 1-5/8 (41.3)

1 (25.4) 9 (228.6) 11-1/4 (285.8) 9-1/4 (235.0) 6-1/4 (158.8) 2-1/4 (57.2)

1-1/4 (31.8) 11-1/4 (285.8) 14-1/16 (357.2) 11-5/8 (295.3) 7-7/8 (200.0) 2-7/8 (73.0)

Recommended Edge Distance Requirements for Shear Loads

Combined Shear and Tension Loading—for Epcon A7 Adhesive AnchorsAllowable loads for anchors under tension and shear loading at the same time (combined loading) will be lower than the allowable loadsfor anchors subjected to 100% tension or 100% shear. Use the following equation to evaluate anchors in combined loading conditions:

Na 5/3 + Va 5/3 Na = Applied Service Tension Load Va = Applied Service Shear Load

Ns Vs Ns = Allowable Tension Load Vs = Allowable Shear Load( () ) <= 1

Technical Data

Epcon A7 Acrylic


REBARREBAR

164164




Critical Interpolated Interpolated MinimumAnchor Embedment Edge Distance Edge Distance Edge Distance Edge DistanceDiameter Depth In. (mm) In. (mm) In. (mm) In. (mm)In. (mm) In. (mm) (100% Load Capacity) (90% Load Capacity) (80% Load Capacity) (70% Load Capacity)3/8 (9.5) 3-3/8 (85.7) 2-1/2 (63.5) 1-15/16 (49.2) 1-3/8 (34.9) 13/16 (26.2) 4-1/2 (114.3) 3-3/8 (85.7) 2-5/8 (66.7) 1-7/8 (47.6) 1-1/8 (28.6)

1/2 (12.7) 4-1/2 (114.3) 3-3/8 (85.7) 2-5/8 (66.7) 1-7/8(47.6) 1-1/8 (28.6) 6 (152.4) 4-1/2 (114.3) 3-1/2 (88.9) 2-1/2 (63.5) 1-1/2 (38.1)

5/8 (15.9) 5-5/8 (142.9) 4-3/16 (106.4) 3-1/4 (82.6) 2-5/16 (58.7) 1-3/8 (34.9) 7-1/2 (190.5) 5-5/8 (142.9) 4-3/8 (111.1) 3-1/8 (79.4) 1-7/8 (47.6)

3/4 (19.1) 6-3/4 (171.5) 5-1/16 (128.6) 3-15/16 (100.0) 2-13/16 (71.4) 1-5/8 (15.9) 9 (228.6) 6-3/4 (171.5) 5-1/4 (133.4) 3-3/4 (95.3) 2-1/4 (57.2)

1 (25.4) 9 (228.6) 6-3/4 (171.5) 5-1/4 (133.4) 3-3/4 (95.3) 2-1/4 (57.2) 12 (304.8) 9 (228.6) 7 (177.8) 5 (127.0) 3 (76.2)

1-1/4 (31.8) 11-1/4 (285.8) 8-7/16 (214.3) 6-9/16(166.7) 4-3/4 (120.7) 2-7/8 (73.0) 15 (381.0) 11-1/4 (285.8) 8-3/4 (222.2) 6-1/4 158.8) 3-3/4 (95.3)

Recommended Edge Distance Requirements for Tension Loads

Anchor Embedment Critical Spacing Interpolated Spacing Minimum SpacingDiameter Depth In. (mm) In. (mm) In. (mm)In. (mm) In. (mm) (100% Load Capacity) (90% Load Capacity) (80% Load Capacity)3/8 (9.5) 3-3/8 (85.7) 4-3/16 (106.4) 2-1/2 (63.5) 13/16 (20.6) 4-1/2 (114.3) 5-5/8 (142.9) 3-3/8 (85.7) 1-1/8 (28.6)

1/2 (12.7) 4-1/2 (114.3) 5-5/8 (142.9) 3-3/8 (85.7) 1-1/8 (28.6) 6 (152.4) 7-1/2 (190.5) 4-1/2 (114.3) 1-1/2 (38.1)

5/8 (15.9) 5-5/8 (142.9) 7 (177.8) 4-3/16 (106.4) 1-3/8 (34.9) 7-1/2 (190.5) 9-3/8 (238.1) 5-5/8 (142.9) 1-7/8 (47.6)

3/4 (19.1) 6-3/4 (171.5) 8-7/16 (214.3) 5 (127.0) 1-5/8 (41.3) 9 (228.6) 11-1/4 (285.8) 6-3/4 (171.5) 2-1/4 (57.2)

1 (25.4) 9 (228.6) 11-1/4 (285.8) 6-3/4 (171.5) 2-1/4 (57.2) 12 (304.8) 15 (381.0) 9 (228.6) 3 (76.2)

1-1/4 (31.8) 11-1/4 (285.8) 14-1/16 (357.2) 8-1/2 (215.9) 2-7/8 (73.0) 15 (381.0) 18-3/4 (476.3) 11-1/4 (285.8) 3-3/4 (95.5)

Recommended Spacing Requirements for Tension Loads

Technical Data

Epcon A7 Acrylic


165165




LOAD FACTOR DISTANCE FROM EDGE OF CONCRETE

Critical Edge Distance—Tension 100% Tension Load 0.75* Anchor Embedment (or greater)

Minimum Edge Distance—Tension 70% Tension Load 0.25* Anchor Embedment

Critical Edge Distance—Shear 100% Shear Load 1.25* Anchor Embedment (or greater)

Minimum Edge Distance—Shear 10% Shear Load 0.25* Anchor Embedment

LOAD FACTOR DISTANCE FROM ANOTHER ANCHOR

Critical Spacing—Tension 100% Tension Load 1.25* Anchor Embedment (or greater)

Minimum Spacing—Tension 80% Tension Load 0.25* Anchor Embedment

1 Use linear interpolation for load factors at edge distances or spacing distances between critical and minimum.

Epcon A7 Adhesive Anchoring SystemSpacing/Edge Distance Load Factor Summary1


166166




Description/Suggested Specifications*Fast Curing Epoxy for All Conditions

The hardener and resin are completely mixed as they aredispensed from the dual cartridge through a static mixingnozzle. The pre-mixed adhesive is injected directly into theanchor hole. C6 can be used with threaded rod or rebar (forfastening to hollow base materials, see pages 96 and 99).

Advantages• 1 hour cure time (see below)• Works in damp holes and underwater applications• Minimum shrinkage—can be used in oversized holes and diamond cored holes• High heat deflection temperature: 140°F (ASTM D648)• One formula for both solid and hollow base materials• NSF standard 61 certified for drinking water systems• Extensively tested—earthquake, underwater, creep, freeze-thaw, radiation, fire, fatigue electrical isolation, ozone and many more test programs have been conducted on C6• Extensive use—C6 has been used on projects all over the world for over 13 years

• When starting new cartridge ornozzle, dispense and discard enoughadhesive until uniform grey color isachieved. Insert the nozzle into thebottom of the hole and fill to 1/2the hole depth.

Installation Steps

• Insert the selected rod slowly byhand into the bottom of the holewith a slow twisting motion. Thisinsures the adhesive fills voids andcrevices uniformly.

• See C6 Cure Time Charts for set-uptime. After the recommended curetime is met, install and tighten fixtureinto place.

Approvals/listingsICBO Evaluation Service, Inc. – #ER-4285City of Los Angeles – RR#24975City of Los Angeles – RR#24929NSF Standard 61 Certified for Drinking Water ComponentsASTM C881-90, Type IV, Grade 3, Class A, B, and CDOT Approvals (see page 11)

• Drill proper sized hole. Clean outhole from bottom with forced air.Complete hole preparation with useof a brush and repeat cleaning withforced air (leave no dust or slurry)

Curing Times Full Temperature Working Curing (F °/C°) T ime Time 120˚ / 49˚ 4 Minutes 1 Hour 90˚ / 32˚ 5 Minutes 1 Hour 70˚ / 20˚ 7 Minutes 1 Hour 60˚ / 16˚ 10 Minutes 2 Hours 50˚ / 10˚ 20 Minutes 24 Hours 40˚ / 4˚ 45 Minutes 32 Hours

C6 FAST CURING EPOXYC6 FAST CURING EPOXY

C6

Reliable PerformanceC6 Always Works Even Under The Most SevereInstallation Conditions




167167

Part Description Box/Bag QTY Carton QTY

C6 Adhesive, 22 Fl. Oz. Cartridge 1 12

Mixing Nozzle for C6-22 Cartridge 24 24

Hand Dispenser for C6-22 and C6-18 Cartridges 1 1

Box/Bag Carton Part Description Qty Qty

C6 Adhesive 2 Fl. Oz. Cartridge 12 12

Mixing Nozzle for C6-2 Cartridge 24 24

Hand Dispenser for C6-2 Cartridge 1 1

Maintenance Kit 6 pcs. C6-2 Cartridges, 12 pcs. E12 Nozzles,1 pc. E400 Tool 1 1

Epcon C6 22 oz. Ordering Information


Box/Bag Carton Part Description Qty Qty

C6 Adhesive,18 Fl. Oz. Cartridge 1 12

Mixing Nozzle (1/2" outside diameter) 4 24


Hand Dispenser for C6-18 Cartridge 1 1

Pneumatic Dispenser for C6-18 Cartridge 1 1


C6 FAST CURING EPOXY C6 FAST CURING EPOXY




Suggested SpecificationsEPOXY ADHESIVE:1. Two component, 100% solid (containing no solvents), non-sag paste, insensitive to moisture, grey in color

2. Meets NSF Standard 61 for use in conjunction with drinking water systems

3. Meets ASTM C881-90, Type IV, Grade 3, Class A, B, and C with the exception of gel time

4. Shrinkage during cure per ASTM D2566: .00051 in./in. maximum

5. Compressive strength, ASTM D695: 10,300 psi minimum

6. Shelf life: 3 years minimum

7. Water solubility: None

8. Heat deflection temperature, ASTM D648: 140°F minimum

Packaging:1. Disposable, self-contained cartridge system capable of dispensing both epoxy components in the proper mixing ratio

2. Epoxy components dispensed through a static mixing nozzle that thoroughly mixes the material, and places the epoxy at the base of the pre-drilled hole

3. Cartridge markings: Include manufacturer ’s name, batch number and dating, mix ratio by volume, ANSI hazard classification, and appropriate ANSI handling precautions

Hole Embedment Depth In Inches (mm) Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15Rebar Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (381.0)# 3 1/2 316.7 158.4 105.6 79.2 63.3 52.8 45.2 39.6 35.2 31.7 28.8 26.4 24.4 22.6 21.1

# 4 5/8 239.3 119.6 79.8 59.8 47.9 39.9 34.2 29.9 26.6 23.9 21.8 19.9 18.4 17.1 16.0

# 5 3/4 183.5 91.8 61.2 45.9 36.7 30.6 26.2 22.9 20.4 18.4 16.7 15.3 14.1 13.1 12.2

# 6 7/8 148.2 74.1 49.4 37.0 29.6 24.7 21.2 18.5 16.5 14.8 13.5 12.3 11.4 10.6 9.9

# 7 1-1/8 71.0 35.5 23.7 17.7 14.2 11.8 10.1 8.9 7.9 7.1 6.5 5.9 5.5 5.1 4.7

# 8 1-1/4 63.2 31.6 21.1 15.8 12.6 10.5 9.0 7.9 7.0 6.3 5.7 5.3 4.9 4.5 4.2

# 9 1-3/8 65.9 33.0 22.0 16.5 13.2 11.0 9.4 8.2 7.3 6.6 6.0 5.5 5.1 4.7 4.4

# 10 1-1/2 53.9 27.0 18.0 13.5 10.8 9.0 7.7 6.7 6.0 5.4 4.9 4.5 4.1 3.9 3.6

# 11 1-3/4 33.0 16.5 11.0 8.2 6.6 5.5 4.7 4.1 3.7 3.3 3.0 2.7 2.5 2.4 2.2

* Approximate number of anchors for 22 Oz. Cartridge: Multiply the number of 18 Oz. anchors by 1.22.

Epcon C6 18 Fluid Ounce Cartridge Estimating Number of Anchoring Installations Per Cartridge*Using Reinforcing Bar with C6 Adhesive in Solid Concrete

Hole Embedment Depth In Inches (mm)Rod Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15In. (mm) Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (381.0)1/4 (6.4) 5/16 587.3 293.7 195.8 146.8 117.5 97.9 83.9 73.4 65.3 58.7 53.4 48.9 45.2 42.0 39.2

3/8 (9.5) 7/16 340.0 170.0 113.3 85.0 68.0 56.7 48.6 42.5 37.8 34.0 30.9 28.3 26.2 24.3 22.7

1/2 (12.7) 9/16 244.7 122.4 81.6 61.2 48.9 40.8 35.0 30.6 27.2 24.5 22.2 20.4 18.8 17.5 16.3

5/8 (15.9) 3/4 125.2 62.6 41.7 31.3 25.0 20.9 17.9 15.7 13.9 12.5 11.4 10.4 9.6 8.9 8.3

3/4 (19.1) 7/8 99.1 49.5 33.0 24.8 19.8 16.5 14.2 12.4 11.0 9.9 9.0 8.3 7.6 7.1 6.6

7/8 (22.2) 1 82.0 41.0 27.4 20.5 16.4 13.7 11.7 10.3 9.1 8.2 7.5 6.8 6.3 5.9 5.5

1 (25.4) 1-1/8 67.6 33.8 22.5 16.9 13.5 11.3 9.7 8.4 7.5 6.8 6.1 5.6 5.2 4.8 4.5

1-1/4 (31.8) 1-3/8 51.2 25.6 17.0 12.8 10.2 8.5 7.3 6.4 5.7 5.1 4.6 4.3 3.9 3.7 3.4

• The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bi ts, the nominal areas of the reinforcing bars and the stress areaof the threaded rods. These estimates do not account for waste.

• Approximate number of anchors for 22 Oz. Cartridge: Multiply the number of 8 Oz. anchors by 1.22.

Epcon C6 18 Fluid Ounce Cartridge Estimating Number of Anchoring Installations Per Cartridge*Using Threaded Rod with C6 Adhesive in Solid Concrete

REBAR

THREADED ROD





169169

2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) 6000 PSI (41.4 MPa) Concrete Concrete ConcreteThreaded Setting Embedment Ultimate Ultimate Ultimate Ultimate Ultimate UltimateRod Dia. Torque In Concrete Tension Shear Tension Shear Tension ShearIn. (mm) Ft.-Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 13 - 18 (17.6-24.4) 3-3/8 (85.7) 7,195 (32.0) 5,209 (23.2) 8,445 (37.6) 5,869 (26.1) 10,621 (47.2) 5,941 (26.4) 4-1/2 (114.3) 8,317 (37.0) 5,209 (23.2) 10,021 (44.6) 5,869 (26.1) 10,603 (47.2) 5,941 (26.4)

1/2 (12.7) 22 - 25 (29.8-33.9) 4-1/2 (114.3) 13,271 (59.0) 11,427 (50.8) 17,684 (78.7) 12,585 (56.0) 17,684 (78.7) 12,585 (56.0) 6 (152.4) 19,127 (85.1) 11,427 (50.8) 19,608 (87.2) 12,585 (56.0) 19,608 (87.2) 12,585 (56.0)

5/8 (15.9) 55 - 80 (74.6-108.5) 5-5/8 (142.9) 17,704 (78.8) 18,294 (81.4) 24,526 (109.1) 19,802 (88.1) 24,526 (109.1) 19,802 (88.1) 7-1/2 (190.5) 22,642 (100.7) 18,294 (81.4) 28,766 (128.0) 19,802 (88.1) 29,456 (131.0) 19,802 (88.1)

3/4 (19.1) 106 - 160 (143.7-216.9) 6-3/4 (171.5) 28,779 (128.0) 25,723 (114.4) 31,521 (140.2) 25,723 (114.4) 33,759 (150.2) 25,723 (114.4) 9 (228.6) 31,758 (141.3) 25,723 (114.4) 41,384 (184.0) 25,723 (114.4) 41,384 (184.0) 25,723 (114.4)

7/8 (22.2) 185 - 250 (250.8-338.9) 7-7/8 (200.0) 35,257 (156.8) -- -- 37,714 (167.8) 30,295 (134.8) 41,023 (182.5) 32,573 (144.9) 10-1/2 (266.7) -- -- -- -- 51,211 (227.8) 30,295 (134.8) 51,211 (227.8) 32,573 (144.9)

1 (25.4) 276 - 330 (374.2-447.4) 9 (228.6) 40,334 (179.4) 38,519 (171.3) 47,886 (213.0) 40,341 (179.5) 47,886 (213.0) 46,416 (206.5) 12 (304.8) 48,719 (216.7) 38,519 (171.3) 62,194 (276.7) 40,341 (179.5) 63,053 (280.5) 46,416 (206.5)

1-1/4 (31.8) 370 - 660 (501.6-894.8) 11-1/4 (285.8) 55,654 (247.6) 65,085 (289.5) 56,981 (253.5) 65,085 (289.5) -- -- 65,085 (289.5) 15 (381.0) 65,728 (289.5) 65,085 (289.5) 79,726 (354.7) 65,085 (289.5) -- -- 65,085 (289.5)

1 Allowable working loads for the single installations under static loading should not exceed 25% capacity or the allowable loa d of the anchor rod.

2 Ultimate load values in 2000, 4000, and 6000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment sho wn in the Embedment in Concrete column. Performance values are based on the use of high strength threaded rod (ASTM A193 Gr. B7). The use of lower strength rods will r esult in lower ultimate tension and shear loads.

Epcon C6 Epoxy Adhesive Performance TableAverage Ultimate Tension and Shear Loads 1,2,3 for Threaded Rod Installed in Solid Concrete

Threaded Drill Hole Embedment Ultimate UltimateRod Dia. Diameter Depth Anchor Tension ShearIn. (mm) In. (mm) In. (mm) Location Lbs. (kN) Lbs. (kN)3/8 (9.5) 7/16 (11.1) 3 (76.2) GROUTED CELL 4,862 (21.6) -- --

1/2 (12.7) 5/8 (15.9) 3 (76.2) GROUTED CELL 4,953 (22.0) -- --

1/2 (12.7) 5/8 (15.9) 6 (152.4) GROUTED CELL 8,214 (36.5) -- --

5/8 (15.9) 3/4 (19.1) 5 (127.0) GROUTED CELL 7,355 (32.7) -- --

3/4 (19.1) 7/8 (22.2) 6 (152.4) Note 1 17,404 (77.4) 19,588 (87.1)

3/4 (19.1) 7/8 (22.2) 6 (152.4) Note 2 17,404 (77.4) 8,668 (38.6)

1 Anchor can be located in grouted cell, “T" joint, or bed joint.

2 Anchor can be located in first grouted cell from edge.

3 Allowable working loads for the single installations under static loading should not exceed 25% (an industry standard) capacity or the allowable load of the anchor rod. Loads based upon testing with ASTM A193, Grade B7 rods.

Average Ultimate Tension And Shear Loads1,2,3 For Threaded RodInstalled In Grout Filled Concrete Block

Combined Shear and Tension Loading—for Adhesive AnchorsAllowable loads for anchors under tension and shear loading at the same time (combined loading) will be lower than the allowabl e loads for anchors

subjected to 100% tension or 100% shear . Use the following equation to evaluate anchors in combined loading conditions:

Na 5/3 + Va 5/3 Na = Applied Service Tension Load Va = Applied Service Shear Load

Ns Vs Ns = Allowable Tension Load Vs = Allowable Shear Load( () ) <=1


THREADED ROD





Threaded Embedment Allowable Tension Load Based On Adhesive Strength Allowable Tension Load Based On Steel StrengthRod Dia. Depth 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) 6000 PSI (41.4 MPa) ASTM A307 ASTM A193 GR. B7 AISI 304 SSIn. (mm) In. (mm) Concrete Lbs. (kN) Concrete Lbs. (kN) In Concrete Lbs. (kN) (SAE 1018) Lbs. (kN) (SAE 4140) Lbs. (kN) Lbs. (kN)3/8 (9.5) 3-3/8 (85.7) 1,800 (8.0) 2,110 (9.4) 2,655 (11.8) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8) 4-1/2 (114.3) 2,080 (9.2) 2,505 (11.1) 2,655 (11.8) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8)

1/2 (12.7) 4-1/2 (114.3) 3,315 (14.8) 4,420 (19.7) 4,420 (19.7) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8) 6 (152.4) 4,780 (21.3) 4,900 (21.8) 4,900 (21.8) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8)

5/8 (15.9) 5-5/8 (142.9) 4,425 (19.7) 6,130 (27.3) 6,130 (27.3) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0) 7-1/2 (190.5) 5,660 (25.2) 7,190 (32.0) 7,364 (32.8) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0)

3/4 (19.1) 6-3/4 (171.5) 7,195 (32.0) 7,885 (35.1) 8,440 (37.5) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1) 9 (228.6) 7,940 (35.3) 10,345 (46.0) 10,345 (46.0) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1)

7/8 (22.2) 7-7/8 (200.0) 8,810 (39.2) 9,430 (41.9) 10,260 (45.6) 11,600 (51.6) 25,510 (113.5) 20,835 (92.7) 10-1/2 (266.7) -- -- 12,080 (57.0) 12,805 (57.0) 11,600 (51.6) 25,510 (113.5) 20,835 (92.7)

1 (25.4) 9 (228.6) 10,085 (44.9) 11,970 (53.3) 11,970 (53.0) 15,180 (67.5) 31,620 (140.7) 26,560 (118.1) 12 (304.8) 12,180 (54.2) 15,545 (69.2) 15,760 (70.1) 15,180 (67.5) 31,620 (140.7) 26,560 (118.1)

1-1/4 (31.8) 11-1/4 (285.8) 13,915 (61.9) 14,245 (63.4) 14,245 (63.4) 23,800 (105.9) 49,580 (220.6) 34,670 (154.2) 15 (381.0) 16,340 (72.7) 19,930 (88.7) 19,930 (88.7) 23,800 (105.9) 49,580 (220.6) 34,670 (154.2)

1 Use lower value of either bond or steel strength for allowable tensile load.

2 Allowable loads taken from ICBO Evaluation Report #4285.

3 Linear interpolation may be used for intermediate spacing and edge distances.

Allowable Tension Loads1,2,3 For Threaded Rod Installed In Solid Concrete

Allowable Shear Load Based On Concrete Strength Allowable Shear Load Based On Steel StrengthThreaded Minimum 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) 6000 PSI (41.4 MPa) ASTM A307 ASTM A193 GR. B7Rod Dia. Embedment Concrete Concrete Concrete (SAE 1018) (SAE 4140) AISI 304 SSIn. (mm) Depth In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 3-3/8 (85.7) 1,300 (5.8) 1,465 (6.5) 1,500 (6.7) 1,040 (4.6) 2,170 (9.7) 1,995 (8.9)

1/2 (12.7) 4-1/2 (114.3) 2,855 (12.7) 3,145 (14.0) 3,145 (14.0) 1,870 (8.3) 3,895 (17.3) 3,585 (15.9)

5/8 (15.9) 5-5/8 (142.9) 4,575 (20.3) 4,950 (22.0) 4,950 (22.0) 2,940 (13.1) 6,125 (27.2) 5,635 (25.1)

3/4 (19.1) 6-3/4 (171.5) 6,430 (28.6) 6,430 (28.6) 6,430 (28.6) 4,250 (18.9) 8,855 (39.4) 7,440 (33.1)

7/8 (22.2) 7-7/8 (200.0) -- -- 7,575 (33.7) 8,140 (36.2) 5,800 (25.8) 12,760 (56.8) 10,730 (47.7)

1 (25.4) 9 (228.6) 9,630 (42.8) 10,085 (44.9) 11,600 (51.6) 7,590 (33.8) 15,810 (70.3) 13,285 (59.1)

1-1/4 (31.8) 11-1/4 (285.8) 16,270 (72.4) 16,270 (72.4) 16,270 (72.4) 11,900 (52.9) 24,790 (110.3) 18,840 (83.8)

1 Use lower value of either concrete or steel strength for allowable shear load.

2 Allowable loads taken from ICBO Evaluation Report #4285.

3 Linear interpolation may be used for intermediate spacing and edge distances.

Allowable Shear Loads1,2,3 For Threaded Rod Installed In Solid Concrete


THREADED ROD





171171

Ultimate Tensile And Yield Strength 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) Grade 60 RebarReinforcing Embedment Concrete Concrete Minimum Yield Minimum UltimateBar In Concrete Ultimate Tension Ultimate Tension Strength Tensile StrengthIn. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)# 3 (9.5) 3-3/8 (85.7) 7,020 (31.2) 9,200 (40.9) 6,600 (29.4) 9,900 (44.0) 4-1/2 (114.3) 9,000 (40.1) 11,540 (51.3) 6,600 (29.4) 9,900 (44.0)

# 4 (12.7) 4-1/2 (114.3) 11,940 (53.1) 15,140 (67.3) 12,000 (53.4) 18,000 (80.1) 6 (152.4) 16,703 (74.3) 18,880 (84.0) 12,000 (53.4) 18,000 (80.1)

# 5 (15.9) 5-5/8 (142.9) 14,120 (62.8) 27,740 (123.4) 18,600 (82.7) 27,900 (124.1) 7-1/2 (190.5) 20,040 (89.1) 30,727 (136.7) 18,600 (82.7) 27,900 (124.1)

# 6 (19.1) 6-3/4 (171.5) 17,940 (79.8) 29,200 (129.9) 26,400 (117.4) 39,600 (176.2) 9 (228.6) 25,520 (113.5) 41,640 (185.2) 26,400 (117.4) 39,600 (176.2) 10 (254.0) -- -- 45,000 (200.2) 26,400 (117.4) 39,600 (176.2)

# 7 (22.2) 7-7/8 (200.0) -- -- 45,850 (204.0) 36,000 (160.1) 54,000 (240.2) 10-1/2 (266.7) -- -- 60,375 (268.6) 36,000 (160.1) 54,000 (240.2) 13 (330.2) -- -- 65,300 (290.5) 36,000 (160.1) 54,000 (240.2)

# 8 (25.4) 9 (228.6) 30,960 (137.7) 54,180 (241.1) 47,400 (210.9) 71,100 (316.3) 12 (304.8) 30,960 (137.7) 65,420 (291.0) 47,400 (210.9) 71,100 (316.3) 16 (406.4) -- -- 86,700 (385.7) 47,400 (210.9) 71,100 (316.3)

# 9 (28.6) 10-1/8 (257.2) -- -- 61,530 (273.7) 60,000 (266.9) 90,000 (400.4) 13-1/2 (342.9) -- -- 81,240 (361.4) 60,000 (266.9) 90,000 (400.4) 19 (482.6) -- -- 108,000 (480.4) 60,000 (266.9) 90,000 (400.4)

# 10 (31.8) 11-1/4 (285.8) 44,600 (198.4) 76,500 (340.3) 76,200 (339.0) 114,300 (508.5) 15 (381.0) 49,220 (218.9) 82,320 (366.2) 76,200 (339.0) 114,300 (508.5) 19 (482.6) -- -- 120,000 (533.8) 76,200 (339.0) 114,300 (508.5)

1 Allowable working loads for the single installations under static loading should not exceed 25% ultimate capacity or the allo wable load of the anchor rod.

2 Ultimate load values in 2000 and 4000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in the Embedment in Concrete column. Performance values are based on minimum Grade 60 reinforcing bar . The use of lower strength rods will result in lower ultimate tension and shear loads.

Average Ultimate Tension Loads1,2 for Reinforcing Bar Installed in Solid Concrete

Spacing/Edge Distance Load Factor Summary 1

LOAD FACTOR DISTANCE FROM EDGE OF CONCRETE

Critical Edge Distance—Tension100% Tension Load 1.25* Anchor Embedment (or greater)

Minimum Edge Distance—Tension70% Tension Load 0.50* Anchor Embedment

Critical Edge Distance—Shear100% Shear Load 1.25* Anchor Embedment (or greater)

Minimum Edge Distance—Shear30% Shear Load 0.50* Anchor Embedment

LOAD FACTOR DISTANCE FROM ANOTHER ANCHOR

Critical Spacing—Tension100% Tension Load 1.50* Anchor Embedment (or greater)

Minimum Spacing—Tension

75% Tension Load 0.75* Anchor Embedment


Technical DataTension and Spacing

REBAR





Description/Suggested Specifications*Extended Working Time EpoxyThe epoxy resin and hardener are completely mixed as they aredispensed from the dual cartridge through a static mixing nozzle,directly into the anchor hole. G5 can be used with threaded rod orrebar.

Advantages• Nozzles last longer—saves money• Gives more time to install anchors• Easier to install anchors in hot weather

• Easier installation of larger diameter anchors and deeper embedments• Odorless

Approvals/listingsICBO Evaluation Service Inc. – #ER-5308City of Los Angeles – RR#25270ASTM C881-90, Type II, Grade 3, Class A, B, and CDOT ApprovalsMetro-Dade County

Suggested SpecificationsEPOXY ADHESIVE:• Two component, 100% solids (containing no solvents), non-sag paste, insensitive to moisture, tan in color• Meets ASTM C881-90, Type II, Grade 3, Classes A, B, and C with the exception of bond strength• Shrinkage during cure per ASTM D2566: .00004 in./in• Compressive strength, ASTM D695: 9170 psi minimum• Shelf life: 2 years minimum• Water solubility: None

1. Drill proper sized hole. Clean out hole from bottom with forced air. Complete hole preparation with use of a brush and repeat cleaning with forced air (leave no dust or slurry).

2. When starting new cartridge or nozzle, dispense and discard enough adhesive until uniform tan color is achieved. Insert the nozzle into the bottom of the hole and fill to 1/2 the hole depth.

Installation Steps

3. Insert the selected rod slowly by hand into the bottom of the hole with a slow twisting motion. This insures the adhesive fills voids and crevices uniformly.

4. See G5 Cure Time Charts for set-up time. After the recommended cure time is met, install and tighten fixture into place.

Curing Times Full Temperature Working Curing (F˚/C˚) Time Time 120 ° / 49° 18 Minutes 8 Hours 90 ° / 32° 34 Minutes 8 Hours 70 ° / 20° 45 Minutes 8 Hours 60 ° / 16° 50 Minutes 9 Hours 50 ° / 10° 60 Minutes 24 Hours 40 ° / 4° 68 Minutes 32 Hours

G5 Extended Working Time EpoxyProvides Longer Working Time In Environments Where Other Adhesives Set Too Fast

G5 EXTENDED TIME WORKING EPOXY G5 EXTENDED TIME WORKING EPOXY




173173

Box/bag Carton Part Description Qty Qty G5 Adhesive, 18 Fluid Oz. Cartridge 1 12



Hand Dispenser for G5-18 Cartridge 1 1

Pneumatic Dispenser for G5-18 Cartridge 1 1

Refer to page 104 for ordering information on brushes and hole plugs

Hole Embedment Depth In Inches (mm) Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15Rebar Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (381.0)# 3 1/2 316.7 158.4 105.6 79.2 63.3 52.8 45.2 39.6 35.2 31.7 28.8 26.4 24.4 22.6 21.1

# 4 5/8 239.3 119.6 79.8 59.8 47.9 39.9 34.2 29.9 26.6 23.9 21.8 19.9 18.4 17.1 16.0

# 5 3/4 183.5 91.8 61.2 45.9 36.7 30.6 26.2 22.9 20.4 18.4 16.7 15.3 14.1 13.1 12.2

# 6 7/8 148.2 74.1 49.4 37.0 29.6 24.7 21.2 18.5 16.5 14.8 13.5 12.3 11.4 10.6 9.9

# 7 1-1/8 71.0 35.5 23.7 17.7 14.2 11.8 10.1 8.9 7.9 7.1 6.5 5.9 5.5 5.1 4.7

# 8 1-1/4 63.2 31.6 21.1 15.8 12.6 10.5 9.0 7.9 7.0 6.3 5.7 5.3 4.9 4.5 4.2

# 9 1-3/8 65.9 33.0 22.0 16.5 13.2 11.0 9.4 8.2 7.3 6.6 6.5 5.5 5.1 4.7 4.4

# 10 1-1/2 53.9 27.0 18.0 13.5 10.8 9.0 7.7 6.7 6.0 5.4 4.9 4.5 4.1 3.9 3.6

# 11 1-3/4 33.0 16.5 11.0 8.2 6.6 5.5 4.7 4.1 3.7 3.3 3.0 2.7 2.5 2.4 2.2

*Approximate number of anchors for 22 Oz. cartridge: Multiply the number of 18 Oz. anchors by 1.22.

Epcon G5 18 Fluid Ounce Cartridge Estimating TableNumber of Anchoring Installations Per Cartridge* Using Reinforcing Bar with G5 Adhesive in Solid Concrete

Hole Embedment Depth In Inches (mm)Rod Dia. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15In. (mm) Inches (25.4) (50.8) (76.2) (101.6) (127.0) (152.4) (177.8) (203.2) (228.6) (254.0) (279.4) (304.8) (330.2) (355.6) (381.0)1/4 (6.4) 5/16 587.3 293.7 195.8 146.8 117.5 97.9 83.9 73.4 65.3 58.7 53.4 48.9 45.2 42.0 39.2

3/8 (9.5) 7/16 340.0 170.0 113.3 85.0 68.0 56.7 48.6 42.5 37.8 34.0 30.9 28.3 26.2 24.3 22.7

1/2 (12.7) 9/16 244.7 122.4 81.6 61.2 48.9 40.8 35.0 30.6 27.2 24.5 22.2 20.4 18.8 17.5 16.3

5/8 (15.9) 3/4 125.2 62.6 41.7 31.3 25.0 20.9 17.9 15.7 13.9 12.5 11.4 10.4 9.6 8.9 8.3

3/4 (19.1) 7/8 99.1 49.5 33.0 24.8 19.8 16.5 14.2 12.4 11.0 9.9 9.0 8.3 7.6 7.1 6.6

7/8 (22.2) 1 82.0 41.1 27.4 20.5 16.4 .13.7 11.7 10.3 9.1 8.2 7.5 6.8 6.3 5.9 5.5

1 (25.4) 1-1/8 67.6 33.8 22.5 16.9 13.5 11.3 9.7 8.4 7.5 6.8 6.1 5.6 5.2 4.8 4.5

1-1/4 (31.8) 1-3/8 51.2 25.6 17.0 12.8 10.2 8.5 7.3 6.4 5.7 5.1 4.6 4.3 3.9 3.7 3.4

* The number of anchoring installations is based upon calculations of hole volumes using ANSI tolerance carbide tipped drill bi ts, the nominal areas of the reinforcing bars and the stress areas of the threaded rods. These estimates do not account for waste.

*Approximate number of anchors for 22 Oz. cartridge: Multiply the number of 18 Oz. anchors by 1.22.

Epcon G5 18 Fluid Ounce Cartridge Estimating TableNumber of Anchoring Installations Per Cartridge* Using Threaded Rod with G5 Adhesive in Solid Concrete

Epcon G5 18 oz. Ordering Information Box/Bag Carton Part Description Qty Qty

G5 Adhesive,

22 Fluid Oz. Cartridge 1 12

Mixing Nozzle

for G5-22 Cartridge 24 24

Hand Dispenser for G5-22

and G5-18 Cartridges 1 1

Epcon G5 22 oz. Ordering Information

REBAR

THREADED ROD

Packaging:

• Disposable, self-contained cartridge system capable of dispensing both epoxy components in the proper mixing ratio

• Epoxy components dispensed through a static mixing nozzle that thoroughly mixes the material and places the epoxy at the base of the pre-drilled hole

• Cartridge markings: Include manufacturer ’s name, batch number and dating, mix ratio by volume, ANSI hazard classification, and appropriate ANSI handling precautions





2000 PSI (13.8 MPa) Concrete 4000 PSI (27.6 MPa) Concrete

Threaded Setting Embedment Ultimate Ultimate Ultimate UltimateRod Dia. Torque Concrete Tension Shear Tension ShearIn. (mm) Ft.-Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 13 - 18 (17.6-24.4) 3-3/8 (85.7) 5,060 (22.5) 6,227 (27.7) 8,395 (37.3) 6,227 (27.7) 4-1/2 (114.3) 6,465 (28.8) 6,227 (27.7) 8,395 (37.3) 6,227 (27.7)

1/2 (12.7) 22 - 25 (29.8-33.9) 4-1/2 (114.3) 10,484 (46.6) 12,016 (53.5) 14,064 (62.6) 12,016 (53.5) 6 (152.4) 12,392 (55.1) 12,016 (53.5) 17,318 (77.0) 12,016 (53.5) 7-1/2 (190.5) -- -- 12,016 (53.5) 20,572 (91.5) 12,016 (53.5)

5/8 (15.9) 55 - 80 (74.6-108.5) 5-5/8 (142.9) 14,634 (65.1) 17,547 (78.1) 20,664 (91.9) 17,547 (78.1) 7-1/2 (190.5) 20,182 (89.8) 17,547 (78.1) 26,456 (117.7) 17,547 (78.1) 9-3/8 (238.1) -- -- 17,547 (78.1) 32,249 (143.5) 17,547 (78.1)

3/4 (19.1) 106-160 (143.7-216.9) 6-3/4 (171.5) 18,966 (84.4) 24,918 (110.8) 32,531 (144.7) 24,918 (110.8) 9 (228.6) 25,988 (115.6) 24,918 (110.8) 40,229 (179.0) 24,918 (110.8) 11-1/4 (285.8) -- -- 24,918 (110.8) 47,927 (213.2) 24,918 (110.8)

1 (25.4) 276-330 (374.2-447.4) 9 (228.6) 43,804 (194.9) 43,648 (194.2) 44,835 (199.4) 43,648 (194.2) 12 (304.8) 43,351 (192.8) 43,648 (194.2) 63,691 (283.3) 43,648 (194.2) 15 (381.0) -- -- 43,648 (194.2) 82,547 (367.2) 43,648 (194.2)

1 Allowable working loads for the single installations under static loading should not exceed 25% (an industry standard) capaci ty or the allowable load of the anchor rod.

2 Ultimate load values in 2000 and 4000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in t he Embedment in Concrete column. Performance values are based on the use of high strength threaded rod (ASTM A193 Gr. B7). The use of lower strength rods will result in lower ultimate tension and shear loads.

Average Ultimate Tension and Shear Loads1,2 for Threaded RodInstalled in Solid Concrete

Allowable Tension Load Based On Epoxy Bond Strength Allowable Tension Load Based On Steel Strength

Threaded Minimum 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) ASTM A307 ASTM A193 GR. B7Rod Dia. Embedment Concrete Concrete (SAE 1018) (SAE 4140) AISI 304 SSIn. (mm) Depth In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)3/8 (9.5) 3-3/8 (85.7) 1,265 (5.6) 2,099 (9.3) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8) 4-1/2 (114.3) 1,616 (7.2) 2,099 (9.3) 2,080 (9.3) 4,340 (19.3) 3,995 (17.8)

1/2 (12.7) 4-1/2 (114.3) 3,004 (13.4) 3,516 (15.6) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8) 6 (152.4) 3,098 (13.8) 4,330 (19.3) 3,730 (16.6) 7,780 (34.6) 7,155 (31.8)

5/8 (15.9) 5-5/8 (142.9) 3,659 (16.3) 5,166 (23.0) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0) 7-1/2 (190.5) 5,046 (22.4) 6,614 (29.4) 5,870 (26.1) 12,230 (54.4) 11,250 (50.0)

3/4 (19.1) 6-3/4 (171.5) 4,742 (21.1) 8,133 (36.2) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1) 9 (228.6) 6,497 (28.9) 10,057 (44.7) 8,490 (37.8) 17,690 (78.7) 14,860 (66.1)

1 (25.4) 9 (228.6) 10,951 (48.7) 11,209 (49.9) 15,180 (67.5) 31,620 (140.6) 26,560 (118.1) 12 (304.8) 10,838 (48.2) 15,923 (70.8) 15,180 (67.5) 31,620 (140.6) 26,560 (118.1)

1 Use lower value of either bond or steel strength for allowable tensile load.

Allowable Tension Loads1 for Threaded Rod Installed in Solid Concrete

Technical DataTension

THREADED ROD





175175

Allowable Shear Load Based On Concrete Strength Allowable Shear Load Based On Steel Strength

Threaded Minimum 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) ASTM A307 ASTM A193 GR. B7Rod Dia. Embedment Concrete Concrete (SAE 1018) (SAE 4140) AISI 304 SSIn. (mm) Depth In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 3-3/8 (85.7) 1,557 (6.9) 1,557 (6.9) 1,040 (4.6) 2,170 (9.7) 1,995 (8.9)

1/2 (12.7) 4-1/2 (114.3) 2,621 (11.7) 3,004 (13.4) 1,870 (8.3) 3,895 (17.3) 3,585 (15.9)

5/8 (15.9) 5-5/8 (142.9) 4,387 (19.5) 4,387 (19.5) 2,940 (13.1) 6,125 (27.2) 5,635 (25.1)

3/4 (19.1) 6-3/4 (171.5) 6,230 (27.7) 6,230 (27.7) 4,250 (18.9) 8,855 (39.4) 7,440 (33.1)

1 (25.4) 9 (228.6) 10,912 (48.5) 11,209 (49.9) 7,590 (33.8) 15,810 (70.3) 13,285 (59.1)

1 Use lower value of either concrete or steel strength for allowable shear load.

Allowable Shear Loads1 for Threaded Rod Installed in Solid Concrete

Threaded Hole Embedment 3000 PSI (13.8 MPa) ConcreteRod Dia. Diameter In Concrete Ultimate TensionIn. (mm) In. (mm) In. (mm) Lbs. (kN)1-1/2 (38.1) 1-3/4 (44.5) 13 (330.2) 110,250 (490.4) 17 (431.8) 143,600 (638.8) 19 (482.6) 150,000 (667.3)

2 (50.8) 2-1/4 (57.2) 16 (406.4) 150,000 (667.3) 17 (431.8) 169,700 (754.9)

1 Allowable working loads for the single installations under static loading should not exceed 25% ultimate capacity or the allowable load of the anchor rod.

2 Ultimate load values in 3000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in the Embedment in Concrete column. Performance values are based on the use of high strength threaded rod (ASTM A193 Gr . B7). The use of lower strength rods will result in lower ultimate tension loads.

Average Ultimate Tension Loads1,2 for Large Diameter Threaded RodInstalled in Solid Concrete


THREADED ROD





Combined Shear and Tension Loading—for Epcon G5 Adhesive AnchorsAllowable loads for anchors under tension and shear loading at the same time (combined loading) will be lower than the allowabl e loads for

anchors subjected to 100% tension or 100% shear . Use the following equation to evaluate anchors in combined loading conditions:

Na + V a Na = Applied Service Tension Load Va = Applied Service Shear Load

Ns Vs Ns = Allowable Tension Load Vs = Allowable Shear Load( () )<=1

Ultimate Tensile And Yield Strength 2000 PSI (13.8 MPa) 4000 PSI (27.6 MPa) Grade 60 RebarReinforcing Embedment In Concrete In Concrete Minimum Yield Minimum UltimateBar In Concrete Ultimate Tension Ultimate Tension Strength Tensile StrengthIn. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)# 3 (9.5) 3-3/8 (85.7) 8,800 (39.1) 10,881 (48.4) 6,600 (29.4) 9,900 (44.0) 4-1/2 (114.3) -- -- 10,404 (46.3) 6,600 (29.4) 9,900 (44.0)

# 4 (12.7) 4-1/2 (114.3) -- -- 19,441 (86.3) 12,000 (53.4) 18,000 (80.1) 6 (152.4) 13,218 (58.8) 19,780 (88.0) 12,000 (53.4) 18,000 (80.1)

# 5 (15.9) 5-5/8 (142.9) -- -- 28,240 (125.6) 18,600 (82.7) 27,900 (124.1) 7-1/2 (190.5) 21,304 (94.8) 34,880 (155.2) 18,600 (82.7) 27,900 (124.1)

# 6 (19.1) 6-3/4 (171.5) -- -- 38,929 (173.2) 26,400 (117.4) 39,600 (176.2) 9 (228.6) 34,515 (153.5) 45,550 (202.6) 26,400 (117.4) 39,600 (176.2)

# 7 (22.2) 7-7/8 (200.0) -- -- 51,653 (229.8) 36,000 (160.1) 54,000 (240.2) 10-1/2 (266.7) -- -- 61,230 (272.4) 36,000 (160.1) 54,000 (240.2)

# 8 (25.4) 9 (228.6) -- -- 64,378 (286.4) 47,400 (210.9) 71,100 (316.3) 12 (304.8) 56,471 (251.2) 76,910 (342.1) 47,400 (210.9) 71,100 (316.3)

# 9 (28.6) 10-1/8 (257.2) -- -- 73,462 (326.8) 60,000 (266.9) 90,000 (400.4) 13-1/2 (342.9) -- -- 84,658 (376.6) 60,000 (266.9) 90,000 (400.4)

# 10 (31.8) 11-1/4 (285.8) -- -- 82,547 (367.2) 76,200 (339.0) 114,300 (508.5) 15 (381.0) -- -- 92,406 (411.1) 76,200 (339.0) 114,300 (508.5)

1 Allowable working loads for the single installations under static loading should not exceed 25% ultimate capacity or the allo wable load of the anchor rod.

2 Ultimate load values in 2000 and 4000 psi stone aggregate concrete. Ultimate loads are indicated for the embedment shown in the Embedment in Concrete column. Performance values are based on the use of minimum Grade 60 reinforcing bar . The use of lower strength rods wi ll result in lower ultimate tension and shear loads.

Epcon G5 Epoxy Adhesive Performance TableAverage Ultimate Tension Loads 1,2 for Reinforcing Bar Installed in Solid Concrete

Technical Data





177177

Epcon G5 Adhesive Anchoring System Spacing/Edge Distance Load Factor Summary1

LOAD FACTOR DISTANCE FROM EDGE OF CONCRETE Critical Edge Distance—Tension 100% Tension Load 1.25* Anchor Embedment (or greater)

Critical Edge Distance—Shear 100% Shear Load 1.25* Anchor Embedment (or greater)

LOAD FACTOR DISTANCE FROM ANOTHER ANCHOR Critical Spacing—Tension 100% Tension Load 1.50* Anchor Embedment (or greater)






Description/AdvantagesInserts Used with Epcon C6 and A7

“a" “b" 2"

Section View—Face Concrete Block

HBU-38

Umbrella Inserts—specially designedfor fastening to theface of concreteblock, clay tile orterra cotta. Acceptsrods between 1/4"and 1/2"

HBU-FS

Umbrella Inserts with 3/8"internally threaded sleeve.Removable fastening toconcrete block

Stubby Screens

Specially designedstainless steel screensprovide maximumperformance for ascreen in the front face of hollow concreteblock. Screens availablefor rods 1/4" to 5/8"

Length of rod = a + b + 2"(when using HBU-38)

a = length of rod projecting from wall

b = thickness of wall (3/8" to 2")

2" = length of rod in umbrella

Large bearingsurface inside theblock providesconsistent highload capacity

Portion of screeninside block isenlarged toprovide higherloads, resistanceto torque, and tokeep the screenperpendicular to the wall

Minimum blockthickness 1"(when usingHBU-FS Insert.)

Length optimizedfor fastening tothe front face ofhollow block

Umbrella InsertsAnd Stubby Screens

UMBRELLA INSERTS AND STUBBY SCREENSUMBRELLA INSERTS AND STUBBY SCREENS




179179

Umbrella Inserts Selection Chart Stubby Screens Selection Chart PART DESCRIPTION QTY/BOX 1/4" x 2" Stainless Screen 100

3/8" x 3-1/2" Stainless Screen 100



PART DESCRIPTION BOX CONTENTS Umbrella Insert 20 Umbrella Inserts 20 Centering Rings

Umbrella Flush Sleeve 10 Umbrella Inserts 10 Flush Sleeve Inserts

1. Drill 3/4" diameter hole, 3-3/4" deepusing rotation only drilling mode andcarbide tipped drill bit. Clean outhole with forced air. Complete holepreparation with use of a brush andrepeat cleaning with compressed air(leave no dust or slurry).

2. Place umbrella on piece of threadedrod, expanding umbrella over the rod.Push umbrella into hole.

3. Push umbrella body through the holeand completely into void. Removethreaded rod. (Do not use in solidbase materials. For anchoring intoblock web, ends and mortar joints,use screens.) View and verify umbrellawings expanded behind wall.

4. Place hole plug (E038) 1/8" from endof self-mixing adhesive nozzle.

Hollow Base Material Umbrella

Inserts

5. Dispense and discard a sufficientamount of adhesive from new cartridge until a uniform adhesive mix is achieved.Inject approximately 1-1/2 fl. oz. ofadhesive into umbrella (7 to 8 pumpsusing manual dispenser) to completelyfill umbrella.

6. 3/8" rod uses a centering ring(supplied with inserts) to keep rodperpendicular to the wall.

7. Insert rod into the filled umbrellausing a slow, soft twisting motionuntil it contacts the back of umbrella.

8. Wait for appropriate temperature/curetime before tightening fixture to therecommended torque of 10 ft./lbs.

Umbrella InsertsAnd Stubby Screens

Installation Steps





Umbrella Inserts Estimating TableNumber of Anchoring Installations Per Cartridge* Using

Threaded Rod and Umbrella Inserts with A7 and C6 Adhesives in Hollow Base Material

Rod Hole Dia. Volume Of Umbrella InsertIn (mm) Inches Cartridge With Embedment Of 3-3/4"3/8 (9.5) 3/4 A7 8 fluid oz. 5 A7 28 fluid oz. 17 C6 18 fluid oz. 11 C6 22 fluid oz. 13

* These estimates do not account for waste.

Stubby Screens Estimating TableNumber of Anchoring Installations Per Cartridge* Using Threaded Rod and Stubby Screens with A7

and C6 Adhesives in Hollow Base MaterialRod Hole Dia. Volume Of Screen Length (Inches)In (mm) Inches Cartridge 2 3-1/2 4-1/21/4 (6.4) 3/8 A7 8 fluid oz. 39 A7 28 fluid oz. 135 C6 18 fluid oz. 87 C6 22 fluid oz. 105

3/8 (9.5) 1/2 A7 8 fluid oz. 17 A7 28 fluid oz. 62 C6 18 fluid oz. 40 C6 22 fluid oz. 49




Technical DataUmbrella InsertsAnd Stubby Screens

Max Installation . Ultimate Ultimate Rod Dia. Torque Hole Dia Embedment Tension ShearPart In. (mm) Ft.-Lbs. (Nm) In. (mm) In. (mm) Lbs. (Kn) Lbs. (Kn)Umbrella 3/8 (9.5) 10 (13) 3/4 (19.1) 3-3/4 (95.3) 3,558 (15.8) 3,109 (13.8)

Stubby Screens 1/4 (6.4) 4 (5) 3/8 (9.5) 2 (50.8) 1,550 (6.9) 1,900 (8.5)

3/8 (9.5) 7 (9) 1/2 (12.7) 3-1/2 (88.9) 1,661 (7.4) 2,071 (9.2)

1/2 (12.7) 10 (13) 5/8 (15.9) 3-1/2 (88.9) 2,458 (10.9) 4,467 (19.9)

5/8 (15.9) 13 (17) 3/4 (19.1) 4-1/2 (114.3) 2,543 (10.9) 5,047 (22.4)

1 Allowable working loads should not exceed 25% ultimate capacity . Based upon testing using ASTM A193, Grade B7 rod.

Load Values1 Performance Table Using Epcon A7 in Hollow Concrete Block

Max Installation . Ultimate Ultimate Rod Dia. Torque Hole Dia Embedment Tension ShearPart In. (mm) Ft.-Lbs. (Nm) In. (mm) In. (mm) Lbs. (Kn) Lbs. (Kn)Umbrella 3/8 (9.5) 10 (13) 3/4 (19.1) 3-3/4 (95.3) 1,875 (8.3) 2,200 (9.8)

Stubby Screens 1/4 (6.4) 4 (5) 3/8 (9.5) 2 (50.8) 1,550 (6.9) 1,900 (8.5)

3/8 (9.5) 7 (9) 1/2 (12.7) 3-1/2 (88.9) 1,661 (7.4) 2,071 (9.2)

1/2 (12.7) 10 (13) 5/8 (15.9) 3-1/2 (88.9) 1,873 (8.3) 2,242 (10.0)

5/8 (15.9) 13 (17) 3/4 (19.1) 4-1/2 (114.3) 1,970 (8.8) 3,554 (15.8)

1 Allowable working loads should not exceed 25% ultimate capacity . Based upon testing using ASTM A193, Grade B7 rod.

Load Values1 Performance Table Using Epcon C6 in Hollow Concrete Block





181181

1. Drill proper sized hole,using rotation-only drillingmode. Clean out hole withforced air. Complete holepreparation with use of abrush and repeat cleaningwith forced air (leave nodust or slurry).

2. When starting new cartridgeor new nozzle, dispense anddiscard enough adhesiveuntil uniform gray color isachieved. Insert the nozzleinto the bottom of thescreen and fill screencompletely full (useextension tube if needed toreach bottom of screen).

Installation Steps

3. Insert the filledscreen completelyinto the hole (subflush).

4. While holding the tab of thescreen against the wall, handinsert the selected rod slowlyinto the screen tube with aslow twisting motion. Pullscreen flush to face and coatwith adhesive. Wait forappropriate cure time beforetorquing fixture in place.

Hollow BaseMaterial Screens

Description/Suggested SpecificationsScreens Used with Epcon C6 and A7

Section

Top View

Hollow Concrete BlockMaximum holding strength in concrete block can be obtained by fastening to both the front and back of the block using an Epcon adhesive screen tube and threaded rod.

For fastening to front of block only, refer to page 167.

Brick WallSeismic Retrofit Brick Pinning or fastening to brick—various lengths and diameters available to accommodate site conditions.

The no-drip feature of Epcon A7 adhesive makes it particularly well suited for brickpinning applications.

Technical Data

Screen Tubes

SCREEN TUBESSCREEN TUBES




AdvantagesHBP Series—Nylon Screens• 30%-50% savings from stainless steel screens• Comparable performance values• Easier to insert and span across voids• Less susceptible to damage (from being crushed)

HB Series—Stainless screens• Corrosion resistant• Available in 1/4" to 3/4" diameters• Special version, “dosage control" available for

overhead and underwater installations

Screen Tubes Estimating TableNumber of Anchoring Installations Per Cartridge*

Using Threaded Rod and Epcon Screen Tubes withA7 and C6 Adhesives in Hollow Base Material

Rod Hole Dia. Volume Of Screen Length (Inches)In (mm) Inches Cartridge 6 8 10 131/4 (6.4) 3/8 A7 8 fluid oz. 13 10 8 A7 28 fluid oz. 45 35 28 C6 18 fluid oz. 29 22 18 C6 22 fluid oz. 35 27 22

3/8 (9.5) 1/2 A7 8 fluid oz. 10 8 6 A7 28 fluid oz. 37 29 23 C6 18 fluid oz. 24 19 15 C6 22 fluid oz. 29 23 18



3/4 (19.1) 7/8 A7 8 fluid oz. 2 1 A7 28 fluid oz. 6 5 C6 18 fluid oz. 4 3 C6 22 fluid oz. 5 4


Rod Dia. Screen Length Stainless Steel Screens Nylon ScreensIn. (mm) In. (mm) Qty/Box Qty/Box1/4 (6.4) 6 (152.4) 100 *

8 (203.2) 100 *

10 (254.0) 100 *

3/8 (9.5) 6 (152.4) 50 50

8 (203.2) 25 25

10 (254.0) 25 25

1/2 (12.7) 6 (152.4) 50 50

8 (203.2) 25 25

10 (254.0) 25 25

5/8 (15.9) 6 (152.4) 25 40

8 (203.2) 20 40

10 (254.0) 20 40

3/4 (19.1) 8 (203.2) 20 *

10 (254.0) 10 20

13 (330.2) 10 20

* Not available in standard strength nylon screens. Longer screens available through specials.

Screen Tubes Selection Chart

HB Stainless Screen HBP Nylon Screen


Screen Tubes




183183

Rod Dia. Hole Dia. Max Installation Torque Embedment Ultimate Tension Ultimate ShearIn. (mm) In. (mm) Ft.-Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN)1/4 (6.4) 3/8 (9.5) 5 (6) 8 (203.2) 2,072 (9.2) 2,264 (10.1)

3/8 (9.5) 1/2 (12.7) 12 (16) 8 (203.2) 2,360 (10.5) 2,668 (11.9)

1/2 (12.7) 5/8 (15.9) 19 (25) 8 (203.2) 2,647 (11.8) 2,668 (11.9)

5/8 (15.9) 3/4 (19.1) 26 (35) 8 (203.2) 2,647 (11.8) 3,578 (15.9)

3/4 (19.1) 7/8 (22.2) 28 (37) 8 (203.2) 2,647 (11.8) 4,573 (20.3)

1 Allowable working loads should not exceed 25% of ultimate capacity . Loads based upon testing with ASTM A193, Grade B7 rods.

Load Values Performance TableAverage Ultimate Loads for HBP (nylon) or HB (stainless) Screens Used with

Epcon A7 in Hollow Concrete Block1

Rod Dia. Hole Dia. Max Installation Torque Embedment Ultimate Tension Ultimate ShearIn. (mm) In. (mm) Ft.-Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN)1/4 (6.4) 3/8 (9.5) 5 (6) 8 (203.2) 2,072 (9.2) 2,264 (10.1)

3/8 (9.5) 1/2 (12.7) 12 (16) 8 (203.2) 2,800 (12.5) 2,466 (10.9)

1/2 (12.7) 5/8 (15.9) 19 (25) 8 (203.2) 3,487 (15.5) 2,668 (11.9)

5/8 (15.9) 3/4 (19.1) 26 (35) 8 (203.2) 3,487 (15.5) 3,578 (15.9)

3/4 (19.1) 7/8 (22.2) 28 (37) 8 (203.2) 3,487 (15.5) 4,573 (20.3)


Load Values Performance TableAverage Ultimate Loads for HBP (nylon) or HB (stainless) Screens Used with

Epcon C6 in Hollow Concrete Block1

Hole Dia. Single Brick Double Brick Brick And Hollow Block

In. (mm) Ultimate Tension Ultimate Shear Ultimate Tension Ultimate Shear Ultimate Tension Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)1/2 (12.7) 2,150 (9.6) -- -- 4,675 (20.8) 1,917 (8.5) 3,659 (16.3)

1/2 (12.7) 2,200 (9.8) 1,143 (5.1) 6,175 (27.5) 1,743 (7.8) 3,659 (16.3)

1/2 (12.7) 2,000 (8.9) 950 (4.2) 3,272 (14.6) 2,498 (11.1) 2,498 (11.1)

5/8 (15.9) 3,800 (16.9) -- -- 6,369 (28.3) 2,498 (11.1) 5,595 (24.9)

5/8 (15.9) 1,750 (7.8) -- -- 7,530 (33.5) 2,305 (10.3) 3,500 (15.6)

5/8 (15.9) 2,618 (11.6) -- -- 2,885 (12.8) 2,305 (10.3) 2,498 (11.1)


Load Values Performance TableAverage Ultimate Loads for HBP (nylon) Screens Used with

Epcon C6 in Brick and Concrete Block1

Technical Data





1. Drill & clean hole.

2. Insert capsule(s).

3. Doublenut threaded rod.

4. Impact CapsuleHammer rebar(rod) to holebottom.

5. Maxima 7 CapsuleSpin (hammerdrill) chisel pointedthreaded rod to holebottom.

6. Allow tocure Installfixture. Applytorque.

Installation Steps for Capsules

Rod Dia. Capsule Dia.* QtyRebar Size (Dia. X Length) PerIn. (mm) In. (mm) Box3/8 (9.5) 3/8 x 3-1/2 (9.5 x 88.9) 10

1/2 (12.7) 1/2 x 3-3/4 (12.7 x 95.3) 10

5/8 (15.9) 5/8 x 3-3/4 (15.9 x 95.3) 10

3/4 (19.1) 3/4 x 6-1/2 (19.1 x 165.1) 10

# 3 3/8 x 3-1/2 (9.5 x 88.9) 10

# 4 1/2 x 3-3/4 (12.7 x 95.3) 10

# 5 5/8 x 3-3/4 (15.9 x 95.3) 10

# 6 3/4 x 6-1/2 (19.1 x 165.1) 10

* Capsules can be stacked for deeper embedments and higher strengths.

Capsule Dia.* QtyRod Dia (Dia. X Length PerIn. (mm) In. (mm) Box Drive Socket**3/8 (9.5) 3/8 x 3-3/8 (9.5 x 85.7) 10 9/16 x 3/8 (14.3 x 9.5)

1/2 (12.7) 1/2 x 3-3/4 (12.7 x 95.3) 10 3/4 x 3/8 (19.1 x 9.5) 3/4 x 3/8 (19.1 x 9.5)

5/8 (15.9) 5/8 x 3-3/4 (15.9 x 95.3) 10 15/16 x 3/8 (23.8 x 9.5) 15/16 x 3/4 (23.8 x 19.1)

3/4 (19.1) 3/4 x 6-1/2 (19.1 x 165.1) 10 1- 1/8 x 3/4 (28.6 x 19.1)

1 (25.4) 1 x 7-1/2 (25.4 x 190.5) 10 1- 1/2 x 3/4 (38.1 x 19.1)

* Capsules can be stacked for deeper embedments and higher strengths.

** Provided by contractor.

Epcon Maxima 7Spin-In CapsulesOrdering InformationEpcon Impact Hammer-In Capsules

Ordering Information

Full Temperature Curing (F˚/C˚) Time 68 ° / 20° 20 Minutes 50 ° / 10° 1 Minutes 32 ° / 0° 1 Hour 23 ° / -5° 2 Hours

Impact And Maxima 7Capsules

Description/SuggestedSpecifications

Impact CapsuleTwo-part Vinylester capsules—hardener andresin are mixed in the hole as a rebar (rod)is hammered (no spinning needed) throughthe capsule to the bottom of the hole, crushingthe capsule and mixing its contents.

Maxima 7 CapsulePatented Acrylic 7™ chemistry now available ina glass capsule—hardener and resin are mixedin the hole as a chisel-pointed rod is spun(hammer-drilled) through the capsule to thebottom of the hole, pulverizing the capsuleand completely mixing the contents.

ImpactHammer-In Capsule

Maxima 7Spin-In Capsule

IMPACT AND MAXIMA 7 CAPSULESIMPACT AND MAXIMA 7 CAPSULES




185185

Epcon Impact Hammer-In Capsules Performance TableAllowable Tension and Shear Loads1 for Threaded Rod Installed in Solid Concrete

Allowable Working Loads Lbs. (kN) Based On Bond Strength Based On Steel Strength

4000 PSI ≥2000 PSI ASTM A307 ASTM AISIThreaded Hole Max. 27.6 (MPa) 13.8 (MPa) A193 GR. B7 304SSRod Dia. Hole Dia. Depth Torque Concrete ConcreteIn. (mm) In. (mm) In. (mm) (Ft-Lb) Tension Shear Tension Shear Tension Shear Tension Shear3/8 (9.5) 7/16 (11.1) 3-5/8 (92.1) 27 1,846 (8.2) 1,390 (6.2) 2,080 (9.3) 1,040 (4.6) 4,340 (19.3) 2,170 (9.7) 3,995 (17.8) 1,995 (8.9)

1/2 (12.7) 9/16 (14.3) 4-3/8 (111.1) 40 3,270 (14.5) 2,415 (10.7) 3,730 (16.6) 1,870 (8.3) 7,780 (34.6) 3,895 (17.3) 7,155 (31.8) 3,585 (15.9)

5/8 (15.9) 11/16 (17.5) 5 (127.0) 80 4,780 (21.3) 4,045 (18.0) 5,870 (26.1) 2,940 (13.1) 12,230 (54.4) 6,125 (27.2) 11,250 (50.0) 5,635 (25.1)

3/4 (19.1) 7/8 (22.2) 6-3/4 (171.5) 160 6,090 (27.1) 4,690 (20.1) 8,490 (37.8) 4,250 (18.9) 17,690 (78.7) 8,855 (39.4) 14,860 (66.1) 7,440 (33.1)

Epcon Maxima 7 Spin-In Capsules Performance TableAllowable Tension and Shear Loads1 for Threaded Rod Installed in Solid Concrete

Allowable Working Loads Lbs. (kN) Based On Bond Strength Based On Steel Strength 4000 PSI 6000PSI ≥2000 PSI ASTM AISIThreaded Hole Max 27.6 (MPa) 41.4 (MPa) 13.8 (MPa) ASTM A307 A193 GR. B7 304SSRod Dia. Hole Dia. Depth Torque Concrete Concrete ConcreteIn. (mm) In. (mm) In. (mm) (Ft-Lb) Tension Tension Shear Tension Shear Tension Shear Tension Shear3/8 (9.5) 7/16 (11.1) 3-5/8 (92.1) 27 2,493 (11.1) 2,623 (11.7) 1,390 (6.2) 2,080 (9.3) 1,040 (4.6) 4,340 (19.3) 2,170 (9.7) 3,995 (17.8) 1,995 (8.9)

1/2 (12.7) 9/16 (14.3) 4-3/8 (111.1) 40 4,053 (18.0) 4,531 (20.2) 2,415 (10.7) 3,730 (16.6) 1,870 (8.3) 7,780 (34.6) 3,895 (17.3) 7,155 (31.8) 3,585 (15.9)

5/8 (15.9) 11/16 (17.5) 5 (127.0) 80 4,965 (22.1) 6,149 (27.4) 4,045 (18.0) 5,870 (26.1) 2,940 (13.1) 12,230 (54.4) 6,125 (27.2) 1 1,250 (50.0) 5,635 (25.1)

3/4 (19.1) 1 (25.4) 6-3/4 (171.5) 160 7,927 (35.3) 9,620 (42.8) 4,690 (20.9) 8,490 (37.8) 4,250 (18.9) 17,690 (78.7) 8,855 (39.4) 14,860 (66.1) 7,440 (33.1)

1 (25.4) 1-1/8 (28.6) 8-1/4 (209.6) 270 14,380 (64.0) 14,380 (64.0) 9,350 (41.6) 15,180 (67.5) 7,590 (33.7) 31,620 (140.7) 15,810 (70.3) 26,560 (118.1) 13,285 (59.1)

1 Use lower value of either bond or steel strengths for allowable tensile and shear loads.

Epcon Impact Hammer-In Capsules Performance TableTension Loads for Reinforcing Bar Installed in 4000 PSI Solid Concrete

Hole Yield Strength Embed To Ultimate Strength Embed ToRebar Dia. Grade 60 Rebar Exceed Yield Number Of Grade 60 Rebar Exceed Ultimate Number OfSize In. (mm) Lbs. (kN) In. (mm) Impact Capsules Lbs. (kN) In. (mm) Impact Capsules#3 1/2 (12.7) 6,600 (29.4) 3-1/2 (88.9) 1 9,900 (44.0) 7 (177.8) 2

#4 5/8 (15.9) 12,000 (53.4) 4 (101.6) 1 18,000 (80.1) 8 (203.2) 2

#5 3/4 (19.1) 18,600 (82.7) 5 (127.0) 1 27,900 (124.1) 10 (254.0) 2

#6 7/8 (22.2) 26,400 (117.4) 6-5/8 (168.3) 1 39,600 (176.2) 13-1/4 (336.6) 2

Technical Data

ImpactHammer-In Capsule

Maxima 7Spin-In Capsule

IMPACT AND MAXIMA 7 CAPSULESIMPACT AND MAXIMA 7 CAPSULES




ROD HOLE DIAMETER DIAMETER PART # QTY/BAG 3/8" 7/16" E038 25

1/2" 9/16" E012 25

5/8" 3/4" E058 20

3/4" 7/8" E034 20

7/8" 1" E078 10

1" 1-1/8" E010 10

1-1/4" 1-3/8" E114 10

SIZE DIA. DESCRIPTION PART # QTY/BAG 1/2" Nylon Brush B012 1

3/4" Nylon Brush B034 1

1" Nylon Brush B100 1

1-1/4" Nylon Brush B114 1

1-1/2" Nylon Brush B112 1

3/8" Wire Brush BW-038 1




1" Wire Brush BW-010 1

BrushesProper hole cleaning using a brush is essential to achieve optimum performance

Hole Plugs Special plugs make overhead installations easier, centers rod in hole, and keeps adhesive off threads

PARTSPARTS




187187

Plastic Extension TubingAttaches to Epcon System nozzles for deep hole installations

DESCRIPTION PART # QTY/BAG 25-Foot Roll Tubing

(.32 in I.D. x .38 in. O.D.) E25 1

10-Foot Straight Tubing

(.39 in. I.D. x .43 in. O.D. ) E25-6 6

DESCRIPTION PART # QTY/BAG Rubber Piston Pads for E101 Hand Dispenser RK109 2

Plastic Piston Rod for E400 Hand Dispenser E400-P 1

Tool Repair Parts

PARTSPARTS




Anchor Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 1/4" x 1-1/4" 1/4" 7/8" 500 500 1/4" x 1-1/2" 1/4" 7/8" 500 500 1/4" x 2" 1/4" 1-1/4" 500 500 1/4" x 2-1/2" 1/4" 1-1/4" 500 500 1/4" x 3" 1/4" 1-1/4" 500 500 1/4" x 3-1/2" 1/4" 1-1/4" 500 500 1/4" x 4" 1/4" 1-1/4" 500 500 1/4" x 4-1/2" 1/4" 1-1/4" 500 500 1/4" x 5" 1/4" 1-1/4" 500 500 1/4" x 5-1/2" 1/4" 1-1/4" 500 500 1/4" x 6" 1/4" 1-1/4" 250 250 1/4" x 6-1/2" 1/4" 1-1/4" 250 250 1/4" x 7" 1/4" 1-1/4" 250 250 1/4" x 7-1/2" 1/4" 1-1/4" 250 250 1/4" x 8" 1/4" 1-1/4" 250 250 1/4" x 9" 1/4" 1-1/4" 250 250 1/4" x 10" 1/4" 1-1/4" 250 250 1/4" x 11" 1/4" 1-1/4" 100 100 1/4" x 12" 1/4" 1-1/4" 100 100 1/4" x 13" 1/4" 1-1/4" 100 100 1/4" x 14" 1/4" 1-1/4" 100 100

Perma-Seal™ CoatedCarbon Steel Spike®

Anchor Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 1/4" x 1" 1/4" 7/8" 100 1000 1/4" x 1-1/4" 1/4" 1" 100 1000 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000 1/4" x 2" 1/4" 1-1/4" 100 1000 1/4" x 2-1/2" 1/4" 1-1/4" 100 1000 1/4" x 3" 1/4" 1-1/4" 100 1000 1/4" x 3-1/2" 1/4" 1-1/4" 100 1000 1/4" x 4" 1/4" 1-1/4" 100 500

3/8" x 2" 3/8" 1-3/4" 25 250 3/8" x 2-1/2" 3/8" 1-3/4" 25 250 3/8" x 3" 3/8" 1-3/4" 25 250 3/8" x 3-1/2" 3/8" 1-3/4" 25 250 3/8" x 4" 3/8" 1-3/4" 25 250 3/8" x 5" 3/8" 1-3/4" 25 250 3/8" x 6" 3/8" 1-3/4" 25 250

1/2" x 2-3/4" 1/2" 2-1/2" 50 200 1/2" x 3-1/2" 1/2" 2-1/2" 50 150 1/2" x 4" 1/2" 2-1/2" 25 150 1/2" x 5" 1/2" 2-1/2" 25 150 1/2" x 6-1/2" 1/2" 2-1/2" 25 150

The published length is measured from below the head to the end of the anchor .

Mushroom Head Grade 8.2Carbon Steel Spike®

Anchor Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000 1/4" x 2" 1/4" 1-1/4" 100 1000 1/4" x 2-1/2" 1/4" 1-1/4" 100 1000 1/4" x 3" 1/4" 1-1/4" 100 1000 1/4" x 3-1/2" 1/4" 1-1/4" 100 1000 1/4" x 4" 1/4" 1-1/4" 100 500

The published length is the overall length of the anchor .

Flat Head Grade 8.2Carbon Steel Spike®

Anchor Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 1/4" x 1" 1/4" 7/8" 100 1000 1/4" x 1-1/4" 1/4" 1" 100 1000 1/4" x 1-1/2" 1/4" 1-1/4" 100 1000 1/4" x 2" 1/4" 1-1/4" 100 1000 1/4" x 2-1/2" 1/4" 1-1/4" 100 1000 1/4" x 3" 1/4" 1-1/4" 100 1000 1/4" x 3-1/2" 1/4" 1-1/4" 100 1000 1/4" x 4" 1/4" 1-1/4" 100 500

3/8" x 2" 3/8" 1-3/4" 25 250 3/8" x 2-1/2" 3/8" 1-3/4" 25 250 3/8" x 3" 3/8" 1-3/4" 25 250

1/2" x 3-1/2" 1/2" 2-1/2" 50 200 1/2" x 4" 1/2" 2-1/2" 25 150 **1/2" x 6-1/2" 1/2" 2-1/2" 25 150

Published length is measured form below the head to the end of the anchor .*Supplied with EPDM Sealing Washer. **Discontinued item once stock is exhausted.

Mushroom Head Type 316Stainless Steel Spike®

The Spike® is a one-piece tamper proof, vibration resistant anchor for use in concrete, block, brick or stone. Several head styles and anchor materials are available.

The Spike®anchor is formed with an “s" shaped configuration at the working end of the anchor to create an expansion mechanism. Since the anchor is pre expanded, there is no secondary tightening operation required which greatly reduces the overall cost of an anchor installation.

SPIKE® Drive Anchor

Sizes

SPIKESPIKE® ANCHORS ANCHORS




189189

Performance Data

Drill Dia. Embed. Depth 3,000 PSI Concrete 4,000 PSI Concrete 5,000 PSI Concrete Concrete Block

Tension Load (LBS) 1/4 “ 7/8" 790 880 980 435 1/4 “ 1" 970 1,045 1,125 645 1/4 “ 1 1/4" 1,080 1,465 1,660 770 3/8" 1 3/4" 1,990 2,420 2,570 N/A 1/2" 2 1/2" 4,870 5,470 5,630 N/A

Shear Load (LBS) 1/4 “ 7/8" 1,980 2,140 2,270 1,350 1/4 “ 1" 2,290 2,350 2,530 1,620 1/4 “ 1 1/4" 2,430 2,610 2,840 1,890 3/8" 1 3/4" 5,610 6,235 6,500 N/A 1/2" 2 1/2" 7,730 7,880 8,210 N/A

Drill Dia. Embed. Depth 3,000 PSI Concrete 4,000 PSI Concrete 5,000 PSI Concrete Concrete Block

Tension Load (LBS) 1/4 “ 7/8" 820 945 1,010 440 1/4 “ 1" 975 1,135 1,185 670 1/4 “ 1 1/4" 1,100 1,550 1,700 800 3/8" 1 3/4" 2,530 3,140 3,435 N/A 1/2" 2 1/2" 5,460 6,030 6,470 N/A Shear Load (LBS) 1/4 “ 7/8" 2,040 2,230 2,360 1,650 1/4 “ 1" 2,310 2,460 2,640 1,840 1/4 “ 1 1/4" 2,500 2,750 3,200 2,100 3/8" 1 3/4" 6,310 7,080 7,150 N/A 1/2" 2 1/2" 12,540 15,300 16,100 N/A

Ultimate Tension and Shear Load Capacities for Carbon Steel Spike®

The following ultimate load capacities are based on tests conducted according to ASTM Standards E 488.

Ultimate Tension and Shear Load Capacities for Stainless Steel Spike®

SPIKE® Drive Anchor





2,000 PSI Concrete 4,000 PSI Concrete 6,000 PSI Concrete Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 1/4 “ 1 1/8" 1,650 1,850 2,200 2,320 2,200 2,320 3/8" 1 7/8" 2,840 6,200 5,300 7,810 5,300 7,810 1/2" 2 5/8" 3,200 8,830 6,200 11,340 6,200 11,340

The Drive® is a one piece, tamper-proof, pre-expanded anchor available in carbon steel for use in concrete and steel. Tie-Wire® anchors are used for suspended ceiling applications. The flat head (counter-sunk) style is particularly suited for wood-to concrete anchoring. The round head style is for all other applications requiring fast, permanent installations.

Base Material: Concrete, StoneSize Range: 3/16" x 1" to 1/2" x 3"Anchor Material: Carbon Steel

Drill Min. Std. Std. Size Dia. Depth Box Ctn. 1/4" x 1-1/4" 1/4" 1-1/8" 100 1000 1/4" x 1-1/2" 1/4" 1-1/8" 100 1000 1/4" x 2" 1/4" 1-1/8" 100 1000 1/4" x 2-1/2" 1/4" 1-1/8" 100 1000

3/8" x 2" 3/8" 1-7/8" 25 250 3/8" x 2-1/2" 3/8" 1-7/8" 25 250 3/8" x 3-1/2" 3/8" 1-7/8 25 250

1/2" x 3" 1/2" 2-5/8" 25 125

Round Head Drive®

Drill Min. Std. Std. Size Dia. Depth Box Ctn. 1/4" x 2" 1/4" 1-1/8" 100 1000 1/4" x 2-1/2" 1/4" 1-1/8" 100 1000 1/4" x 2-1/2" 1/4" 1-1/8" 100 1000 1/4" x 2-1/2" 1/4" 1-1/8" 100 1000 1/4" x 2-1/2" 1/4" 1-1/8 100 1000 1/4" x 2-1/2" 1/4" 1-1/8" 100 500

Flat Head Drive®

Drill Min. Std. Std. Size Dia. Depth Box Ctn. 1/4" x 1-3/4" 1/4" 1-1/8" 500 500 1/4" x 1-3/4" 1/4" 1-1/8" 100 500

T ie-Wire Setting Tool 1 1

Tie-WireDrive® (13/64" Tie-Wire Hole)

Drive®Split Drive Type Anchor

Round Head Drive®

Flat Head Drive®

Tie-Wire Drive®

Performance Data

The following ultimate load capacities are based on tests conducted according to ASTM Standards E 488.





191191

Head Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 1/4" 3/16" 1-1/4" 100 1000 3/8" 1/4" 1-3/4" 50 500

Rod Hanging Pipe Spike®Grade 8.2 Carbon Steel

Drill Min. Tie-Wire Std. Std. Size Dia. Embed. Hole Size Box Ctn. 1/4" 1/4" 1-3/4" 9/32" 100 500

Suspended Ceilings Tie-Wire Spike®Grade 8.2 Carbon Steel

Anchor Drill Min. Std. Std. Size Dia. Embed. Box Ctn. 3/16" x 1-1/2" 3/16" 1-1/4" 100 1000 3/16" x 2" 3/16" 1-1/4" 100 1000 3/16" x 1-1/2 3/16" 1-1/4" 100 1000 3/16" x 1-1/2 1/4" 1-1/4" 100 1000

Concrete Forming Spike®Grade 8.2 Carbon Steel

Pipe Spike®

Tie Wire Spike®

Forming Spike®

SPIKESPIKE® ANCHORS - SPECIAL APPLICATION ANCHORS - SPECIAL APPLICATIONACCESSORIESACCESSORIES

Spike® Installation Tools Tool Guide Description I.D. Spike ®Driver 1000 1/2" Spike ®Driver 2000 1/2" Spike ®Driver 3000 9/16" Spike ®Driver 6000 1"

Pipe Spike® Tool Tool Tip Description I.D. Pipe Spike® Setting Tool 5/16"

Spike® Puller For Removing Tool Slot Description Width Spike ® Puller 1/4"

Pipe Spike® Tool

Spike® Installation ToolsWhile the Spike® anchor can easily be installed using a hammer, a specially designed series of drivers and manual tools provide a fast, easy to use method for installing Spike® anchors into concrete and masonry materials. The tools allow Spike® anchors to be installed in confined areas and prevent damage to the fixture from stray hammer blows.

Spike® PullerFor removing 3/16" or 1/4" Spike® Anchors

Std. Std. Size Box Ctn. 1/4" (ID) x 1-1/8" (OD) 100 1000

Sealing Washer Type 304Stainless Steel With EPDM Seal

Std. Std. Size Box Ctn. 1/4" (ID) x 1-1/8" (OD) Poly 100 5000

Plastic Washer

Stainless Steel with EPDM Sealing washers and Plastic Washers are typically used with 1/4" diameter anchors for roof flashing, termination bar and dissimilar metal applications.

Washers




C-90 Hollow Block Red Solid Block Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 3/16" 3/4" 270 860 460 920 1/4 “ 5/8" 360 1040 570 1250 1/4 “ 3/4" 480 1160 790 1400 1/4 “ 1" 590 1320 820 1400 1/4 “ 1 3/8" 800 1320 950 1400 1/4 “ 1 1/2" 965 1320 1015 1400

2,000 PSI Concrete 4,000 PSI Concrete 6,000 PSI Concrete Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 1/4 “ 5/8" 480 1230 600 1500 640 1500 1/4 “ 3/4" 580 1230 720 1500 760 1500 1/4 “ 7/8" 770 1350 820 1500 890 1500 1/4 “ 1 1/8" 890 1400 960 1500 1060 1500 1/4 “ 1 3/8" 980 1400 1150 1500 1230 1500 1/4 “ 1 7/8" 1150 1400 1300 1500 1365 1500

The TFC ZAMACTM is a tamper-proof nail drive anchor which has a body formed from Zamac alloy. Nails are available in carbon or stainless steel. The anchor can be used in concrete, block, brick or stone. This anchor is not recommended for applications overhead.

Base Material: Concrete, Block, Brick, StoneSize Range: 3/16" x 7/8" to 1/4" x 2"Anchor Material: Zamac Alloy with Carbon or Stainless Steel Drive Pin

Drill Std. Std. Size Dia. Box Ctn. 1/4" x 3/4" 1/4" 100 500 1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500

Mushroom Head Zamac Nailin® Carbon Steel Nail

Drill Std. Std. Size Dia. Box Ctn. 1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500

Mushroom Head Zamac Nailin® Type 304 Stainless Steel Nail

Drill Std. Std. Size Dia. Box Ctn. 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500

Flat Head Zamac Nailin® Carbon Steel Nail

ZAMAC™Drive Pin Anchor

Performance DataThe following ultimate load capacities are based on tests conducted according to ASTM Standard E 488.

Ultimate Load Capacities - C-90 Hollow Block and Red Solid Block

ZAMAC DRIVE PIN TYPE ANCHORSZAMAC DRIVE PIN TYPE ANCHORS




193193

C-90 Hollow Block Red Solid Block Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 1/4 “ 5/8" 420 1,160 680 1,400 1/4 “ 3/4" 540 1,200 930 1,600 1/4 “ 1" 650 1,400 990 1,600 1/4 “ 1 3/8" 840 1,400 1,150 1,600 1/4 “ 1 1/2" 990 1,400 1,260 1,600

2,000 PSI Concrete 4,000 PSI Concrete 6,000 PSI Concrete Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 1/4 “ 5/8" 675 1,420 850 1,800 890 1,800 1/4 “ 3/4" 790 1,500 920 1,800 1,090 1,800 1/4 “ 7/8" 1,060 1,600 1,190 1,800 1,250 1,800 1/4 “ 1 1/8" 1,220 1,600 1,350 1,800 1,450 1,800 1/4 “ 1 3/8" 1,360 1,600 1,540 1,800 1,650 1,800 1/4 “ 1 7/8" 1,480 1,600 1,600 1,800 1,780 1,800

Drill Std. Std. Size Dia. Box Ctn. 1/4" x 3/4" 1/4" 100 500 1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500 1/4" x 2-1/4" 1/4" 100 500 1/4" x 3" 1/4" 100 500

Zamac Hammer-Screw® AnchorCarbon Steel Mushroom HeadWith No. 2 Phillips Type Screw

Drill Std. Std. Size Dia. Box Ctn. 1/4" x 2" 1/4" 100 500

Master Pack W/Carbon Steel Screw

1/4" x 3/4" 1/4" 1000 1000 1/4" x 1" 1/4" 1000 1000 1/4" x 1-1/4" 1/4" 1000 1000 1/4" x 1-1/2" 1/4" 1000 1000 1/4" x 2" 1/4" 1000 1000 1/4" x 2-1/4" 1/4" 1000 1000 1/4" x 3" 1/4" 1000 1000

Zamac Hammer-Screw® AnchorStainless Steel Mushroom HeadWith No. 2 Phillips Type Screw

The Zamac Hammer-Screw® is a unique, one-step drive anchor featuring a Phillipstype head and a screw thread used for concrete, block, brick or stone. With a bodyformed from corrosion resistant Zamac alloy and carbon or stainless steel drivescrew, this anchor has been developed by Powers as an improvement over standardnail-in anchors. Traditionally, Zamac Nailin® anchors have been used for light duty ,non-engineered applications and have not been recommended for use overhead. Inorder to over come these problems, the new Zamac Hammer-Screw® has beendesigned to provide a removable anchor with 40% higher tension load capacitieswhen installed in concrete. The Zamac Hammer-Screw® can be used overheadprovided it is part of an engineered system designed by an engineer who will takethe proper design considerations and safety factors into account.

Base Material: Concrete, Block, Brick, StoneSize Range: 1/4" x 3/4" to 1/4" x 3"Anchor Material: Zamac Alloy with Carbon or Stainless Steel Drive Screw

Zamac Hammer-Screw®



ZAMAC HAMMER-SCREWZAMAC HAMMER-SCREW®




Nylon Nailin®Plastic Drive Pin Type Anchor

C-90 Hollow Block Red Solid Block Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 3/16" 3/4" 170 280 155 320 3/16" 1" 180 280 170 320 1/4 “ 5/8" 110 320 150 500 1/4 “ 3/4" 160 320 200 500 1/4 “ 1" 170 320 220 500 1/4 “ 1 1/4" 180 320 240 500 1/4 “ 1 1/2" 200 320 250 500

2,000 PSI Concrete 4,000 PSI Concrete 6,000 PSI Concrete Anchor Size Embed. Depth Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) Tension (lbs) Shear (lbs.) 3/16" 3/4" 180 280 195 320 200 320 3/16" 1" 200 280 220 320 230 320 1/4 “ 5/8" 120 320 140 500 180 500 1/4 “ 3/4" 220 320 240 500 245 500 1/4 “ 1" 230 320 250 500 260 500 1/4 “ 1 1/2" 240 320 270 500 280 500 1/4 “ 2" 255 320 285 500 300 500

Drill Std. Std. Size Dia. Box Ctn. 3/16" x 1" 3/16" 100 1000 3/16" x 1-1/2" 3/16" 100 1000

1/4" x 1" 1/4" 100 1000 1/4" x 1-1/4" 1/4" 100 1000 1/4" x 1-1/2" 1/4" 100 1000 1/4" x 2" 1/4" 100 1000

Round Head Nylon Nailin® Carbon Steel Nail

Drill Std. Std. Size Dia. Box Ctn. 3/16" x 7/8" 3/16" 100 500 3/16" x 1-1/2" 3/16" 100 500

1/4" x 1" 1/4" 100 500 1/4" x 1-1/4" 1/4" 100 500 1/4" x 1-1/2" 1/4" 100 500 1/4" x 2" 1/4" 100 500

Flat Head Nylon Nailin® Carbon Steel Nail

Drill Std. Std. Size Dia. Box Ctn. 3/16" x 1" 3/16" 100 1000

1/4" x 3/4" 1/4" 100 1000 1/4" x 1" 1/4" 100 1000 1/4" x 1-1/2" 1/4" 100 1000 1/4" x 2" 1/4" 100 1000 1/4" x 3" 1/4" 100 1000 1/4" x 4" 1/4" 100 1000 1/4" x 6" 1/4" 100 400

Mushroom Head Nylon Nailin® Carbon Steel Nail

The Nylon Nailin® is a pin drive anchor with a body formed from engineered nylon and nails available in carbon and stainless steel. The anchor can be used in concrete, block, or brick. This anchor is not recommended for applications overhead.

Base Material: Concrete, Block, Brick • Size Range: 3/16" x 1" to 1/4" x 6"Anchor Material: Engineered Nylon with Carbon or Stainless Steel Drive Pin



NYLON NAILINNYLON NAILIN® DRIVE PIN TYPE ANCHORS DRIVE PIN TYPE ANCHORSLIGHT DUTY LIGHT DUTY




195195

Screw Drill Std. Std. Mstr. Size Dia. Box Ctn. Ctn. 6" x 3/4" 5/32" 100 1000 5000 6" x 1" 5/32" 100 1000 5000

10" x 1" 3/16" 100 1000 5000 10" x 1-1/4" 3/16" 100 1000 5000 10" x 1-1/2" 3/16" 100 1000 5000

12" x 1" 1/4" 100 1000 5000 12" x 1-1/4" 1/4" 100 1000 5000 12" x 1-1/2" 1/4" 100 1000 5000 12" x 2" 1/4" 100 1000 5000

14" x 1" 9/32" 100 1000 5000 14" x 1-1/4" 9/32" 100 1000 5000 14" x 1-1/2" 9/32" 100 1000 5000 14" x 2" 9/32" 100 1000 5000

16" x 1-1/2" 5/16" 50 500 2500

20" x 1-1/2" 3/8" 50 500 2500 20" x 1" 3/8" 50 500 2500

Fiberplug™ Sheet MetalAnd Wood Screw Sizes

The Fiberplug™ is a jute fiber screw style anchor (formerly know as the Rawplug) designed for use in Concrete, block, brick, stone, and plaster . Designed for use with wood, sheet metal and lag screws.

Base Material: Concrete, Block, BrickSize Range: 3/4" to 3/8" x 3"Anchor Material: Jute Fiber With Lead Liner

Scru-Lead™Lead Screw Anchor

Screw Drill Std. Std. Size Dia. Box Ctn. 3/8" x 2" 7/16" 25 250 3/8" x 2-1/2" 7/16" 25 250 3/8" x 3" 7/16 25 250

Fiberplug™ Lag Screw Sizes

Drill Min. Std. Std. Size Dia. Depth Box Ctn. 6-8" x 3/4" 1/4" 3/4" 100 1000 6-8" x 1" 1/4" 1" 100 1000 6-8" x 1-1/2" 1/4" 1-1/2" 100 1000

10-14" x 1" 5/16" 1" 100 1000 10-14" x 1-1/2" 5/16 1-1/2" 100 1000

16-18" x 1-1/2" 3/8 1-1/2" 25 250

Scru-Lead™

Fiberplug™Fiber Screw Anchor

The Scru-Lead™ anchor is designed for use with sheet metal or wood screws in concrete, block or brick. The anchor is made entirely of a lead alloy which is soft enough for easy installation, but hard enough to give sure, secure holding power . The anchor is recommended for light duty applications where holding power is not a critical factor. It should not be used overhead.Base Material: Concrete, Block, BrickSize Range: No.6-8 x 3/4" to No.16-18 x 1-1/2"Anchor Material: Lead Alloy

FIBERPLUGFIBERPLUG™ AND SCRU-LEAD AND SCRU-LEAD™ ANCHORS ANCHORS

Bantam Plug™

Bantam Plug™ Drill Min. Std. Std. Mstr. Size Dia. Depth Box Ctn. Ctn. 6-8" x 3/4" 3/16" 3/4" 100 1000 5000 8-10 x 7/8" 3/16" 7/8" 100 1000 5000 10-12 x 1" 1/4" 1" 100 1000 5000 14-16 x 1-1/2" 5/16" 1-1/2" 50 500 2500

The Bantam Plug™ anchor is a plastic anchor designed for use with lightweight fixtures with a sheet metal or wood screws in concrete, block or brick. The anchor is recommended for light duty static applications where holding power is not a critical factor . It should not be used overhead.Base Material: Concrete, Block, Brick, WallboardSize Range: No.6-8 x 3/4" to No.16-18 x 1-1/2"Anchor Material: Plastic

LIGHT DUTY LIGHT DUTY




Grade 2 Cap Screw, NC

Diameter Lengths1/4" - 20" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2",1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

5/16" - 18" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

3/8" - 16" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2"

7/16" - 14" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2" 6", 7", 8"

1/2" - 13" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 7", 8

5/8" - 11" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

3/4" - 10" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

7/8" - 9" 2-1/2", 3", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

1" - 8" 2", 2-1/2", 3", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

1-1/4" - 7" 4-1/2", 8"

Grade 2 Cap Screw, NCAvailable Finishes: Plain & Zinc

Hex Bolt (A 307)Diameter Lengths1/4" - 20" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

5/16" - 18" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

3/8" - 16" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 12"

7/16" - 14" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7", 8"

1/2" - 13" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 11-1/2", 12", *13", *14", *15", *16", *17", *18", *19", *20", *21", *22", *23", *24", *26", *28", *32", *36"

5/8" - 11" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 11-1/2", 12", *13", *14", *15", *16", *17", *18", *19", *20", *21", *22", *24", *26", *28", *32", *36"

3/4" - 10" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 11-1/2", 12", *13", *14", *15", *16", *17", *18", *19", *20", *21", *22", *23", *24", *25, *26", *28", *32", *36"

7/8" - 9" 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 11-1/2", 12", *13", *14", *15", *16", *17", *18", *19", *20", *21", *22", *24", *26", *28", *32", *36"

1" - 8" 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 11", 11-1/2", 12", *13", *14", *15", *16", *17", *18", *19", *20", *21", *22", *23", *24", *25", *26", *28", *32", *34", *36"

1-1/8" - 7" 3", 3-1/2", 4", 4-1/2", 4-3/4", 5", 5-1/2", 6", 6-1/2", 7", 8", 9", 9-1/2", 10", 1 1", 12", 13", *14", *16", *18", *19", *20", *24", *26", *28", *32", *34", *36"

1-1/4" - 7" 2-1/2", 3", 3-1/4", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12", *14", *16", *18", *20", *24", *26", *28", *32", *34", *36"

1-1/2" - 6" 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 1 1", 12", *14", *16", *18", *20", *24", *26", *28", *32", *34", *36"

1-3/4" - 5" 4", 4-1/2", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 14", *18", *22", *26", *30"

2-4-1/2" 6", 6-1/2", 7", 7-1/2", 8", 9",

2-1/4" - 4-1/2" 4-1/2", 8", 9"

2-1/2" - 4" 9", 9-1/2"

* With 6 inch THD

Hex Bolt (A 307)Available Finishes: Plain, Zinc,Hot Dip Galvanized

Carbon Steel Bolts

BOLTSBOLTS




197197

Grade 5 Cap Screws, NCDiameter Lengths1/4" - 20" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

5/16" - 18" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6"

3/8" - 16" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 9", 10", 12"

7/16" - 14" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 7", 8"

1/2" - 13" 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12",

9/16" - 12" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

5/8" - 11" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 11-1/2", 12"

3/4" - 10" 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12"

7/8" - 9" 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12"

1" - 8" 1-1/2", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12"

1-1/8" - 7" 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 8", 9", 10", 1 1", 12"

1-1/4" - 7" 2-3/4", 3", 3-1/2", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 10", 1 1", 12"

1-1/2" - 6" 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7", 8", 9", 10", 1 1", 12"

Grade 5 Cap Screws, NCAvailable Finishes: Plain, Zinc

(A-325) Heavy Hex Structural Bolts USADiameter Lengths1/2" - 13" 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4"

5/8" - 11" 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

3/4" - 10" 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 9"

7/8" - 9" 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/4", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

1" - 8" 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

1-1/8" - 7" 2-1/2", 2-3/4", 3", 3-1/2", 4", 4-1/4", 4-1/2", 4-3/4", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8

1-1/4" - 7" 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 4-3/4", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

(A-325) Heavy HexStructural Bolts USAAvailable Finishes: Plain, Hot DipGalvanized

(307A) Carriage BoltsDiameter Lengths1/4" - 20" 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8"

5/16" - 18" 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 9", 10", 1 1", 12"

3/8" - 16" 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/4", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 1 1", 12"

7/16" - 14" 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 3-3/4", 4", 4-1/2", 5", 5-1/2", 6", 7", 8"

1/2" - 13" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/4", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 9-1/2", 10", 10-1/2", 1 1", 11-1/2", 12", 13", 14", 15", 16", 18", 20", 22", 24", 28"

5/8" - 11" 1-1/2", 2", 2-1/2", 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 9", 10", 11", 12", 13", 14", 15", 16", 18", 19", 20", 22", 24", 28"

3/4" - 10" 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 7-1/2", 8", 8-1/2", 9", 10", 11", 12", 13", 14", 15", 16", 18", 20", 24", 28"

(307A) Carriage BoltsAvailable Finishes: Plain, Zinc,Hot Dip Galvanized

Carbon Steel Bolts

Stainless Steel Bolts Available Upon Request

BOLTSBOLTS




Thread Types1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 7/16-14 (5/8" AF), 1/2"-13,

9/16"-12, 5/8"-11, 3/4"-10, 7/8"-9, 1"-8, 1-1/8"-7, 1-1/4"-7, 1-3/8"-6,1-1/2"-6, 1-3/4"-5, 2-4-1/2", 2-1/4"-4-1/2", 2-1/2"-4, 2-3/4"-4, 3"-4

Finished Hex Nuts, NC

Thread Types1/4"-28, 5/16"-24, 3/8"-24, 7/16"-20, 7/16-20 (5/8" AF), 1/2"-20,9/16"-18, 5/8"-18, 3/4"-16, 7/8"-14, 1"-14, 1-1/8"-12, 1-1/4"-12,

1-3/8"-12, 1-1/2"-12, 1-3/4"-12, 2-12

Finished Hex Nuts, NF

Finished Hex Nuts, NCAvailable Finishes: Plain, Zinc,Hot Dip Galvanized

Finished Hex Nuts, NFAvailable Finishes: Plain, Zinc,Hot Dip Galvanized

Thread Types1/2"-13, 5/8"-11, 3/4"-10, 7/8"-9, 1"-8,

Grade C (A325) Heavy Hex Nuts USAGrade C (A325) HeavyHex Nuts USAAvailable Finishes: Plain, Zinc

Stainless Steel Nuts Available Upon Request

Nuts

NUTSNUTS

Thread Types2"-56, 3"-48, 4"-40, 5"-40, 6"-32, 8"-32, 10"-24, 12"-24,

1/4"-20, 5/16"-18, 3/8"-16

Hex Machine Screw Nuts NCHex Machine ScrewNuts NCAvailable Finishes: Zinc

Thread Types2"-64, 3"-56, 5"-44, 6"-40, 10"-32, 12"-28, 1/4"-28, 5/16"-24, 3/8"-24

Hex Machine Screw Nuts NFHex Machine ScrewNuts NFAvailable Finishes: Zinc

Carbon Steel Nuts




199199

Nylon Insert Locknuts NCThread Types

8"-32 (NM), 10"-24 (NM), 12"-24 (NM), 1/4"-20 (NE), 5/16"-18 (NE),3/8"-16 (NE), 7/16"-14 (NE), 1/2"-13 (NE), 9/16"-12 (NE),

5/8"-11 (NE), 3/4"-10 (NE), 7/8"-9 (NE), 1-8 (NE), 1-1/8"-7 (NE),1-1/4"-7 (NE), 1-1/2"-6 (NE)

Nylon InsertLocknuts, NCAvailable Finishes: Zinc

Nylon Insert Locknuts NF

Nylon Insert Locknuts, NFAvailable Finishes: Zinc

Thread Types10"-32 (NM), 1/4"-28 (NE), 5/16"-24 (NE), 3/8"-24 (NE),

7/16"-20 (NE), 1/2"-20 (NE), 9/16"-18 (NE), 5/8"-18 (NE),3/4"-16 (NE), 7/8"-14 (NE), 1-14 (NE), 1-1/8"-12 (NE),

1-1/4"-12 (NE), 1-1/2"-12 (NE)

Thread Types10"-24 x 5/16" x 3/4", 1/4"-20 x 7/16" x 1-3/4",

5/16"-18 x 1/2" x 1-3/4", 3/8"-16 x 9/16" x 1-3/4"7/16"-14 x 5/8" x 1-3/4", 1/2"-13 x 11/16" x 1-3/4"

5/8"-11 x 13/16" x 2-1/8", 3/4"-10 x 1" x 2-1/4"7/8"-9 x 1-1/4" x 2-1/2", 1"-8 x 1-1/4" x 2-1/2"1-1/8"-7 x 1-1/2" x 3", 1-1/4"-7 x 1-5/8" x 3"

1-1/2"-6 x 2" x 4"

Hex Coupling RegularNuts NCAvailable Finishes: Zinc

Thread Types1/4"-28 x 3/8" x 7/8", 5/16"-24 x 7/16" x 7/8",

3/8"-24 x 1/2" x 1-1/8", 7/16"-20 x 9/16" x 1-1/4",1/2"-20 x 5/8" x 1-1/4", 5/8"-18 x 13/16" x 2-1/8",3/4"-16 x 1" x 2-1/4", 7/8"-14 x 1-1/4" x 2-1/2",

1"-14 x 1-3/8" x 2-3/4"

Hex Coupling EconomyNuts NFAvailable Finishes: Zinc

Hex Coupling Economy Nuts NF

Hex Coupling Regular Nuts NC

Stainless Steel Nuts Available Upon Request

NUTSNUTS




USS Flat Washer

SAE Washer

I.D.3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8"

1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", 1-5/8", 1-3/4", 1-7/8"2", 2-1/4", 2-1/2", 3"

Uss Flat Washer Zinc Plated

I.D.No. 6, No. 8, No. 10, No. 12

1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 3/4", 7/8"1", 1-1/4", 1-3/8", 1-1/2"

Sae Washer Zinc Plated

I.D.#4, #6, #10, #12, 1/4", 5/16", 3/8", 7/16", 1/2"

Split Lockwasher -Regular

Fender Washer

I.D. O.D.1/8" - 9/64" 9/16", 1"

1/8" 5/8"

3/16" - 7/32 1", 1-1/8". 1-1/4"

1/4" - 9/32" 1/2", 9/16", 1", 1-1/4", 1-1/2", 2"

5/16" - 11/32" 1/4", 1/2"

3/8" - 13/32" 1", 1-1/4", 1-1/2", 1-5/8", 2"

1/2" - 17/32" 1-1/2", 2"

Fender Washer Zinc Plated

Split LockwasherRegularSteel/Zinc

Carbon Steel Washers

Stainless Steel Washers Available Upon Request

WASHERSWASHERS




201201

AZTEC MasterSeal washers are a practical and simple, yet sturdy and reliable.They are engineered to prevent delamination of metal and sealant.

Features• Bonded sealing washer.• Aluminum, stainless steel or galvanized steel backing standard; Monel backing also available.• EPDM sealer standard; neoprene and silicone also available.• Deflectable, tapered lip on inside diameter assures inner seal around fastener.• Sealant evenly compresses to create a uniform seal.Benefits• Resists shearing and tearing during application.• Excellent sealing abilities.• Retains positive seal regardless of position on flat surfaces and many curved surfaces.• Allows visual confirmation of proper seating.

Visual Inspection Extrusion of sealant at outer edge of properly seated

washer provides easy conformation of proper fastener seal.

Correct Degree of Tightness:Slight circle of sealant extrusion.

Too Tight: Metal backing begins to turn up. Too Loose:

Sealant is not compressed and can not form seal.

Outside Screw Diameter Size 1/2" (9mm) #10, #12, 1/4" or #14"

9/16" #12

5/8" (15mm) #10 or #12, #12, 1/4" or #14", #17, 5/16"

.729" 1/4" or #14", 5/16", 3/8"

1" 5/16", 1/2"

1-1/8" 1/4" or #14"

1-13/16" 5/16"

1-1/2" 1/4" or #14", 5/16"

Outside Screw Diameter Size 1/2" (9mm) #6, #8, #10, #12 1/4" or #14"

9/16" #12"

5/8" (15mm) #10, #12, 1/4" or #14", #17

.729" #10, 1/4" or #14", .729" 5/16", 3/8", 5/16"

7/8" 3/8"

1" 5/16", 3/8"

1-1/8" 1/4" or #14"

20 Gage Galvanized Steel BackingEPDM Sealant

20 Gage 304 Stainless Steel

Backing/EPDM Sealant

Outside Screw Diameter Size 9/16" #12, 1/4" or #14"

5/8" (15mm) #10", #12, 1/4" or #14"

.729" 5/16", 3/8"

1" 5/16"

1-3/16" 5/16"

1-1/2" 5/16"

.040 Aluminum 5052Backing/EPDM Sealant

MASTER SEAL™ Washers Provide An Air, Vapor Or Liquid-Tight Seal

Property Value Test Method Base Material Cross-Linked EPDM (Ethylene propylene diene terpolymer) N/A

Color Black N/A

T est Level 3 Grade

Test Temperature B 100 degrees C Type

Volume Swell A No Requirement Class

Durometer Hardness 70 +/- 5 ASTM D2240

Tensile Stength 10 MPa (1450 PSI) Minimum ASTM D412

Ultimate Elongation 250% Minimum ASTM 412 A/C

Heat Resistance Heat aging 70 hrs @ 100 degrees C ASTM D573 Change / Hardness Maximum + 10 Points Change / Tensile Maximum - 25% Change / Ultimate Elongation Maximum - 25%

Compression Set Maximum 25% ASTM D395B

Ozone Resistance No observed effect (70 hrs. @ 50 pphm) ASTM D1171 100% Quality Retention Facing Low Temperature Brittleness Non-brittle 3 minutes@ -55 degrees C ASTM D2137

UV Resistance Excellent Resistance To Aging Excellent Non-standing Pass

Typical properties of Bonded EPDM Sealing Washer Material

BONDED WASHERSBONDED WASHERS




Hex Lag ScrewsDiameter Lengths1/4" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

5/16" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

3/8" 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7", 8", 9", 10", 12"

1/2" 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 6-1/2", 7", 8", 9", 10", 11", 12", 14", 16", 18", 24"

5/8" 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7", 8", 9", 10", 1 1", 12", 14", 16", 18", 20"

3/4" 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7", 8", 9", 10", 1 1", 12", 14", 16", 18", 20

7/8" 8", 10", 12", 16", 18", 20"

1" 6", 8", 10", 12", 16", 20

Hex Lag ScrewsAvailable Finishes: Plain, Zinc,Hot Dip Galvanized

Carbon Steel Lags

Stainless Steel Lag Screws Available Upon Request

LAG SCREWSLAG SCREWS




203203

RoundPhillips Zinc Plated

Machine Screw Round Phillips - Zinc PlatedDiameter Lengths8" - 32" 1/4", 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3"

10" - 24" 1/4", 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

10" - 32" 1/4", 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3"

12" - 24" 1/4", 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3"

1/4" - 20" 3/8", 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

5/16" - 18" 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

3/8" - 16" 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

Machine Screw Pan Phillips Zinc Plated

Diameter Lengths8" - 32" 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 5", 6"

10" - 24" 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

10" - 32" 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 5", 6"

12" - 24" 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 2", 2-1/4", 3"

1/4" - 20" 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

5/16" - 18" 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

3/8" - 16" 1/2", 5/8", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

1/2" - 13" 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 6"

PanPhillips Zinc Plated

Machine Screw Flat Phillips - Zinc Plated

Diameter Lengths8" - 32" 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 5", 6"

10" - 24" 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

10" - 32" 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2" 2-3/4", 3", 3-1/2", 4", 5", 6"

12" - 24" 1/4", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3"

1/4" - 20" 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 7/8", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 2-3/4", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

5/16" - 18" 1/2", 3/4", 1", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/4", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

3/8" - 16" 1/2", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6"

1/2" - 13" 1", 1-1/4", 1-1/2", 2", 2-1/2", 3", 3-1/2", 4", 4-1/2", 5", 6"

Flat Countersunk Phillips Zinc Plated

Machine Screw Hex Head Unslotted Zinc PlatedDiameter Lengths8" - 32" 1/4", 3/8", 1/2", 3/4", 1", 1-1/4", 1-1/4", 1-1/2"

10" - 24" 1/4", 5/16", 3/8", 1/2", 3/4", 1", 1-1/4", 1-1/2"

10" - 32" 1/4", 5/16", 3/8", 1/2", 3/4", 1", 1-1/4", 1-1/2"

12" - 24" 3/8", 1/2", 3/4", 1", 1-1/4", 1-1/2"

1/4" - 20" 1/2"

5/16" - 18" 1/2"

Machine Screw Hex HeadUnslotted Zinc Plated

Carbon Steel and Zinc Plated

Stainless Steel Machine Screws Available Upon Request

MACHINE SCREWSMACHINE SCREWS




DANDI-EYE FORGED EYEBOLTSDANDI-EYE FORGED EYEBOLTS




205205

• Provides a low-cost solution for a variety of user applications-as protectors for tubing, threaded parts, and as covers for bolts and screws.

• Widely used as masks for painting, plating, shot blasting and powder coating processes.• Available in standard or high-temperature material.• Flexible design can stretch onto slightly larger dimensions for a snug fit without tearing, splitting or

shredding.• Available in custom sizes, alternate colors, and optional lengths if sizes shown are not applicable.Specifications - Standard Caps• Standard Color: Black• Standard Material: Vinyl (PVC)• Temperature Range: Up to 3500F

Dip Molded Vinyl Caps

A=To Fit Length B=1/2" Length B=3/4" Length B=1" Length B=1 1/4" Length B=1 1/2" *5/32" *DM-0156-1/2 DM-0156-3/4 DM-0156-1 DM-0156-1 1/4 DM-0156-1 1/2 *13/64" *DM-0207-1/2 DM-0207-3/4 DM-0207-1 DM-0207-1 1/4 DM-0207-1 1/2 *15/64" *DM-0234-1/2 DM-0234-3/4 DM-0234-1 DM-0234-1 1/4 DM-0234-1 1/2

Use on tips of fasteners for

protectionSpecifications - High-Temp. Caps• Standard Color: Yellow• Standard Material: High Temperature Vinyl (PVC)• Temperature Range: Up to 4500F• To order High Temperature items, add "H" suffix to the

Part Number (Example: DM-0187-1/2H)

DIP MOLDED VINYL CAPSDIP MOLDED VINYL CAPSFOR SCREW TIPSFOR SCREW TIPS

Extra heavy duty natural nylon 6.6 cable ties Loop Bulk Tensile Bundle Military BagLength Strength Width Diameter Specification Qty. 8" 120 lbs. 5/16" 3/16"- 2" - 100 11" 120 lbs. 5/16" 3/16"- 3" - 100 15" 120 lbs. 5/16" 3/16"- 4" - 100 24" 175 lbs. 3/8" 3/16"- 7" - 100 34" 175 lbs. 3/8" 3/16"- 10" - 100 42" 175 lbs. 3/8" 3/16’- 12" - 100

Black weather resistant nylon cable ties Loop Bulk Tensile Bundle Military BagLength Strength Width Diameter Specification Qty. 3.25" 18 lbs. 3/32" 1/16"- 5/8" MS-3367-4-0 1000 5.5" 40 lbs. 1/8" 1/16"- 1-1/4" MS-3367-5-0 1000 8" 50 lbs. 1/8" 1/16"- 2-1/8" MS-3367-4-0 1000 11" 50 lbs. 3/16" 1/16"- 3" MS-3367-7-0 1000 15" 50 lbs. 3/16" 1/16"- 4" MS-3367-2-0 500

Natural nylon 6.6 cable ties screw mount type # 10 screw Loop Bulk Tensile Bundle Military BagLength Strength Width Diameter Specification Qty. 7.5" 50 lbs. 1/8" 1/16"- 1-3/4" - 100 11" 50 lbs. 3/16" 1/16"- 3" - 100

Black weather resistant releasable natural nylon 6.6 cable ties - push button Loop Bulk Tensile Bundle Military BagLength Strength Width Diameter Specification Qty. 5.5" 50 lbs. 1/8" 1/8"- 1-1/4" - 500 8" 50 lbs. 3/16" 1/8"- 2" - 500 11" 50 lbs. 3/16" 1/8"- 3" - 500

• Manufactured of 100% Nylon• Non-Corrosive• Specification: Type 6.6 Nylon• Self-Extinguishing• Natural & Weather Resistant Black Operating Temperatures From 40 ° F (-40° C) to 185° F (85° C).• Recognized Under the Components Program of Underwriter Laboratories, Inc.

File # E 57800

3/4" (19 mm)Rubber-basedAdhesive

1" (25 mm)Rubber-basedAdhesivePush-In Mounts

• Accommodate miniature, intermediate and standard sized cable ties• For use in .250" (6mm) hole

Cable Tie Mounts Adhesive Backed and Screw Mount

1" (25 mm)For use with #6 screw

CABLE TIESCABLE TIES




Bracer Base Dimensions Bracer Max Size Rod Size “L" “W"

#1 5/8" 4.000" 3.000"

#2 7/8" 4.000" 3.000"

#3 1-1/4" 4.000" 3.000"

#4 1-1/2" 4.250" 3.000"

Slot Requirements - MinimumSlots in the web must be large enough to allow a rod angle of 47-degrees maximum. The above dimensions should be considered. Static load tests were conducted using the these dimensions.

L

W

Rod Size W L 1/2" 1.062" 2.125"

5/8" 1.062" 2.125"

3/4" 1.062" 2.125"

7/8" 1.062" 2.125"

1" 1.312" 2.625"

1-1/4" 1.312" 2.625"

1-1/2" 1.625" 3.500"

BRACERBRACER® ® HILLSIDE STYLE WASHERHILLSIDE STYLE WASHER

The BRACER® and BRACER® II with slip resistant knurls are designed to increase the load capacity of your bracing system by over three times more than a standard hillside washer.

BRACER® II with our patented slip resistance knurls minimizes slippage of the rod, keeping the bracing tight. It has been tested by an independent laboratory confirming that BRACER® achieves complete loading of the web and rod, eliminating backup plates and welding! This research provides the only certified load data by any supplier of hillside style washers.

Designed to Improve the Stability of Your Building

BRACERBRACING WASHER

R

• Patented knurls on the surface minimizes slippage of the rod.

• Eliminates back-up plates and welding.

• Special nipple is design to engage the web slot deeper, producing higher load capacity and easy installation!

• Made from high strength ductile iron to assure quality performance.

• Certi f ed independent test data conf rms load capacities.

WHY BRACER® ?

Patented design provides optimal load transfer and easy installa-

Rod Size BRACER #1/2” to 5/8” #1 BRACER (with serrations)3/4” to 7/8” #2 BRACER (with serrations)1” to 1-1/4” #3 BRACER1-3/8” to 1-1/2” #4 BRACER

SIZES AND DIMENSIONS

US Patent # 6,217,270

MATERIAL PROPERTIES

FINISHRed Enamel: BRACER #1,2,3Gray Enamel: BRACER #4Type: gloss enamel, 85 units minimum at 60°.Thickness: 1.6-2.0 milsAdhesion: ASTM 2794 Excellent. No Peeling or removalImpact Resistance: ASTM D 2794 Good > 10 in. lbs.Abrasion Resistance: ASTM D 4060 GoodCorrosion Resistance: Salt Spray: 250 hrs. (<5% red rust) Kesternich: 5 cycles (<10% red rust)

OPTIONAL FINISHHot Dip Galvanized Per ASTM 153 Class A

MATERIAL AND STANDARDDuctile IronASTM 536-84 Grade 65-45-12Ultimate Tensile Strength: 65,000 PSI

OPTIONAL MATERIAL (Domestic)ZAMAC 5 Zinc Aluminum AlloyASTM B86-88 AC41A

For load data, please refer to page 208.

Need a standard hillside?Call about information on

our BRACER LITE!




207207

STRESS-LOK® is the f rst washer designed to keep brace rods tight. It eliminates slippage of the rod caused by vibration due to wind load, earthquakes, cranes and other cyclic loads.

The concave bearing surface with a series of knurls, increases the contact area between the washer and hillside. The additional contact area distributes the load over a greater area, thereby keeping the connection tight. It also improves the overall strength of astandard hillside washer.

Specifi cally Designed for Use With Bracing Washers

For optimal performance of your bracing system, use STRESS-LOK with BRACER Hillside Style Washers.

STRESS-LOK can be use with ordinary hillside washers to improve their performance.

For load data, please refer to page 208.

• The curved mating surface increases performance by distributing the loadonto the hillside.

• The increased contact area eliminates slippage that can loosen the connection.

• Certi f ed independent test dataconf rms load capacities.

• Can be used with standard hillsidewashers to improve their performance.

Patented washer distributes the bracing load across the hillside to increase strength and reduce slippage of the rod.

WHY STRESS-LOK ®?

Flat washers provide minimal contact which can weaken the

connection and causeloosening of the nut.

STRESS-LOK® distributes the load over a greater area which increases strength

compared to standard fl at washers.

INDEPENDENT TESTS

STRESS-LOKCLAMPING WASHER

R

US Patent # 6,217,270

1/2” Rod

SIZES (Rod Size): 1/2”, 5/8” and 3/4”MATERIAL: Low Carbon SteelFINISH: .0003” min. Zinc Plated

SIZES AND DIMENSIONS

5/8” Rod 3/4” Rod

“...Triangle Fastener’s hillside anchors having ridges, serration, on the curvature of the standard hillside washer with Stress-Lok washers were found to be superior to the standard off-the-self market available hillside washers.”

Source: R. Ralph Sinno, Ph.D., P.E., F. ASCE Professor of Civil & Environmental Engineering

Statement from independent laboratory testsconducted at Mississippi State University, August 26, 2008.

E

Increase the stabilityIncrease the stabilityof your building for of your building for

less than $0.50 per rod!less than $0.50 per rod!

STRESS-LOK™ CLAMPING WASHERSTRESS-LOK™ CLAMPING WASHER




BRACER / STRESS-LOK LOAD CHART / REV 2 - 9.10.08 - Added Stress-Lok® Triangle Fastener Corporation – Pittsburgh, PA – 216.351.9933Tests were conducted at Mississippi State University by the direction of Professor R. Ralph Sinno Ph.D., P.E. in accordance to tests sponsored by the MBMA. “X-bracing Anchorage Connection,” Journal of Structural Engineering, ASCE, Vol 119, No. 11, November 1993. Form JS111503 / © Copyright 2003 Triangle Fastener Corporation. Any unauthorized use without written consent is prohibited.

LOAD DATA

BRACERBRACER® ® HILLSIDE STYLE WASHERHILLSIDE STYLE WASHER



TRIANGLE FASTENER CORPORATION 800.486.1832 / www.trianglefastener.com209

TOOLS&

ACCESSORIES

Choose from top name brands of standard and specialty tools for drilling, driving, cutting, grinding, sawing and chopping.

TFC offers the largest selection of professional grade tools and accessories for the commercial construction industry!




Hammer Drills

Drills

Screwguns

We have a wide variety of BOSCH power We have a wide variety of BOSCH power tools to meet your specifi c needs.tools to meet your specifi c needs.

BOSCHBOSCH POWER TOOLSPOWER TOOLS

Grinders

Cordless Tools

• Drilling• Driving• Cutting• Grinding• Sawing• Chopping

Choose a tool to meet your specific need...

Contact our nearest location for more details and ask about our free training programs to assure proper tool use.




211211

Hammer Drills

Drills

Screwguns

We have a wide variety of DEWALT power We have a wide variety of DEWALT power tools to meet your specifi c needs.tools to meet your specifi c needs.

DEWALT POWER TOOLSDEWALT POWER TOOLS

GrindersCordless Tools


Contact our nearest location for more details and ask about our free training programs to assure proper tool use.

Saws

Cut and Shear





FEIN POWER TOOLSFEIN POWER TOOLSNIBBLERS AND SHEARSNIBBLERS AND SHEARS

FEIN power tools for sheet metal applications.FEIN power tools for sheet metal applications.

KETT POWER TOOLSKETT POWER TOOLSSHEARSSHEARSWe have KETT shears and replacement We have KETT shears and replacement

parts to meet your specifi c needs. parts to meet your specifi c needs.

Contact our nearest location for the most up to date information on the tools that best fit your needs. Ask about our free training programs to assure proper tool use.

Nibblers Shears





213213

MAKITA POWER TOOLSMAKITA POWER TOOLS

Hammer Drills

Screwguns

We have a wide variety of MAKITA power We have a wide variety of MAKITA power tools to meet your specifi c needs.tools to meet your specifi c needs.

Grinders

Cordless

Contact TFC for more details and ask about our free training programs to assure proper tool use.

Saws

Choose from a full line of METABO power Choose from a full line of METABO power tools for commercial construction!tools for commercial construction!

METABO POWER TOOLSMETABO POWER TOOLS

Hammer Drills

Grinders





Hammer Drills

Drills

Screwguns

We have a wide variety of MILWAUKEE We have a wide variety of MILWAUKEE power tools to meet your specifi c needs.power tools to meet your specifi c needs.

MILWAUKEE POWER TOOLSMILWAUKEE POWER TOOLS

Cordless


Saws

Milwaukee Electric Tool Corp. is an industry-leading manufacturer and marketer of heavy-duty , portable electric power tools and accessories for professional users worldwide.

Contact TFC for more details and ask about our free training programs to assure proper tool use.





215215

We provide these durable vinyl cords to the same high standards as our specialty cords. They are UL listed and offer long life and durability with resistance to abrasion, weather, water and flame. Choose from 16 to 10 AWG wire and lengths from 10 to 100 feet. All cords feature high-visibility jackets and are ideal for use in a variety of work environments.

Extension Cords

Lighted Connectors

Power indicator light glows when the cord is connected to a power source. It indicates that the cord is "live" and adds a level of safety and convenience that ordinary extension cords can't offer. The Quick Check light has a bluish tint that makes it visible even in direct sunlight.

Specialty Cords

Part Number Cat. No.-Ft.-Color AWG Amps WattsEXTENSION CORDS

3 Conductor, SJTW

C-4314-025-BO 14/3 15 1875 C-4314-050-BO 14/3 15 1875 C-4314-100-BO 14/3 13 1625 C-4312-025-YW 12/3 15 1875 C4312-050-YW 12/3 15 1875 C-4312-100-YW 12/3 15 1875 C-4312-025-WH 12/3 15 1875 C-4312-050-WH 12/3 15 1875 C-4312-100-WH 12/3 15 1875 C-4310-050-YB 10/3 15 1875 C-4310-100-YB 10/3 15 1875

3 Outlet Power Block, SJTW

A-4514-001-OR 14/3 15 1875 C-4514-025-BO 14/3 15 1875 C4514-050-BO 14/3 15 1875 C-4514-100-BO 14/3 13 1625 C-4512-025-YW 12/3 15 1875 C4512-050-YW 12/3 15 1875 C4512-100-YW 12/3 15 1875 C-4510-050-YB 10/3 15 1875 C-4510-100-YB 10/3 15 1875

SPECIALTY CORDS

Quick Check®, SJTW

C4418-015-YR 16/3 13 1625 C-4413-035-YR 14/3 15 1875 C-4413-075-YR 14/3 13 1625

Power Stopper®, Circuit Breaker, Power Block, SITW A-8314-002-RD 14/3 13 1625

Power Stopper®, Circuit Breaker, SJTW, Quick Check®

C-4416-025-RD 16/3 13 1625 C-4416-050-RD 16/3 13 1625 C-4416-100-RD 16/3 10 1250

Quick Check®Power indicator light

American Contractor® Tri-Source® Power Blocks Tri-Source 3-Way Power Blockwith Power Indicator Light Features:

• All-purpose, portable outdoor cord that stays flexible even under the most extreme temperatures to -67°F

• Provides superior resistance to abrasion, ozone, oil, grease, and chemicals

• Outer jacket is flame retardant and water resistant • Power indicator light in the female receptacle to

show that the power is on

Applications: Provides additional outlets for power distribution on industrial or construction job sites where you require tough, durable extension cords

• Bulk cords available.• Custom colors.• Custom imprint with your name and logo.

Part Number Cat. No.-Ft.-Color Amps Watts A-8312-602-YW 15 1875

Power Block, 12/3, STW, 600 volt wire

Technical DataFull Load Current ValuesCurrent values based on usual speed and normal torque.For full load currents of 206V and 200V motors, increase corresponding 220V value above by 6% and 10% respectively.

Current Carrying Capacity of Flexible CordsBased on ambient temperature of 30 0C (860F).

Amperage shown is for not more than three conductors in a cord. If cord has from four to six conductors, decrease the values shown.

The amp capacities under subheading A are applicable to three conductor cords and four conductor cords with three conductors carrying current. The amp capacities under sub heading B are applicable to two conductor cords and three-conductor cords with two conductors carrying current.

NOTE: On extension cords over 50 feet, derate by two wire sizes.

AWG Thermoplastic Types Types Wire ST, STO, SJT, SJTO, HPD, HPN, HSJ Size SVT, SVTO, SPT HSO 18 7 Amps 10 Amps 10 Amps 17 12 16 10 13 15 14 15 18 20 12 20 25 30 10 25 30 35 8 35 40 6 45 55

Motor Rated Motor Voltage 110V to 120V Rated Motor Voltage 220v to 240V Horse Direct Single- Three-Phase Direct Single Three Phase Power Current Phase AC (Induction) AC Current Phase AC (Induction) AC 0.25 2.9 Amps 5.8 Amps - 1.5 Amps 2.9 Amps - 0.33 3.6 7.2 - 1.8 3.6 - 0.25 5.2 9.8 4.0 Amps 2.6 4.9 2.0 Amps 3.4 7.4 13.8 5.6 3.7 6.9 2.8 1 9.4 16.0 7.2 4.7 8.0 3.6 1.5 13.2 20.0 10.4 6.6 10.0 5.2 2 17.0 24.0 13.6 8.5 12.0 6.8 3 25.0 34.0 - 12.2 17.0 9.6 5 40.0 56.0 - 20.0 28.0 15.2 7.5 58.0 80.0 - 29.0 40.0 22.0 10 76.0 100.0 - 38.0 50.0 28.0

POWER CORDSPOWER CORDS




In 1994 the Model 500 system became the first and only code approved fastening system for plywood to light gauge steel shear walls and horizontal diaphragms. Engineers and designers were presented with allowable values and conditions of use relating to a pneumatic fastening system that was arguably three to five times faster than the traditional screw and screw gun method used for fastening plywood and rated sheathing to light gauge steel supports.

Steel Framing Tool Model 500

The Panelfast® system is a revolutionary new method of fastening gypsum sheathing, Dens Glass® Gold, wall panels, fiber cement siding and even vinyl siding to steel framing, 14 gauge and lighter. The Panelfast pin has a large 5/16" diameter head providing excellent wind load test results. The AERICOTE® 1000 coating provides corrosion resistance second only to stainless steel. The Panelfast model 510 pneumatic tool has adjustable depth control that precisely places the pin at the desired depth, yet has the power to pierce 14 gauge steel.

Panelfast® Model 510

Why waste time with screws or other slower, costlier fastening methods, when it can be as fast as nailing to wood?

ET&F PNUEMATIC TOOLSET&F PNUEMATIC TOOLS




Terminology

Shank Diameter

High Speed Steel (HSS)• General Purpose

• Recommended for most drilling applications

118° Point• General Use

Material Types

Overall Length

Flute LengthShank Length Point

Cobalt HSS• Recommended for drilling through alloys, stainless steel, etc.

Titanium Nitride (TiN) Coated HSS• Reduces friction - very wear resistant

• Ideal for production work and repetitive drilling

135° Split Point• For drilling tougher, harder materials, less tendency to “walk".

Great “Sheeters Bit"

The following information is included to help you choosethe right drill bit for your particular requirements

1180 1350

Point Types

DRILL BITSDRILL BITS




Decimal Drill Size .0625 1/16 .0630 1.6mm .0635 52 .0650 1.65mm .0669 1.7mm .0670 51 .0689 1.75mm .0700 50 .0709 1.8mm .0728 1.85mm .0730 49 .0748 1.9mm .0760 48 .0768 1.95mm .0781 5/64 .0785 47 .0787 2.0mm .0807 2.05mm .0610 48 .0620 45 .0827 2.1mm .0846 2.15mm .0660 44 .0866 2.2mm .0686 2.25mm .0690 43 .0906 2.3mm .0925 2.35mm .0935 42 .0938 3/32 .0945 2.4mm .0960 41 .0985 2.45mm

Decimal Drill Size

.0960 40 .0984 2.5mm .0995 39 .1015 38 .1024 2.6mm .1040 37 .1063 2.7mm .1065 36 .1064 7/64 .1 100 35 .1 102 2.8mm .1 110 34 .1 130 33 .1 142 2.9mm .1 160 32 .1 181 3.00mm .1200 31 .1220 3.1mm .1250 1/8 .1260 3.2mm .1285 30 .1299 3.3mm .1339 3.4mm .1360 29 .1378 3.5mm .1405 28 .1406 9/64 .1417 3.6mm .1440 27 .1457 3.7mm .1470 26 .1495 25

.1496 3.8mm .1520 24

Decimal Drill Size

.1535 3.9mm .1540 23 .1562 5/32 .1570 22 .1575 4.00mm .1590 21 .1610 20 .1614 4.1mm .1654 4.2mm .1660 19 .1693 4.3mm .1695 18 .1719 11/64 .1730 17 .1732 4.4mm .1770 16 .1772 4.5mm .1600 15 .181 1 4.6mm .1820 14 .1850 13 .1850 4.7mm .1875 3/16 .1890 12 .1890 4.6mm .1910 11 .1929 4.9mm .1935 10 .1960 9 .1969 5.0mm .1990 8 .2008 5.1mm .2010 7 .2031 13/64

Decimal Drill Size

.2040 6 .2047 5.2mm .2055 5 .2087 5.3mm .2090 4 .2126 5.4mm .2130 3 .2165 5.5mm .2188 7/32 .2205 5.6mm .2210 2 .2244 5.7mm .2280 1 .2283 5.8mm .2323 5.9mm .2340 A .2344 15/64 .2362 6.0mm .2380 B .2402 6.1mm .2420 C .2441 6.2mm .2480 0 .2480 6.3mm .2500 1/4 .2500 E .2520 6.4mm .2559 6.5mm .2570 F .2598 6.6mm .2610 G .2638 6.7mm .2656 17/64

Available Sizes(Up to 17/64" - .2656" diameter)

DECIMAL EQUIVALENT (inch) for Fractional, Number, Letter & Metric

DRILL BITS - SIZE CHARTDRILL BITS - SIZE CHART




Decimal Drill Size

.2660 H .2677 6.8mm .2717 6.9mm .2720 I .2756 7.0mm .2770 J .2795 7.1mm .2810 K .2812 9/32 .2835 7.2mm .2874 7.3mm .2900 L .2913 7.4mm .2950 M .2053 7.5mm .2969 19/64 .2992 7.6mm .3020 N .3031 7.7mm .3071 7.8mm .31 10 7.9mm .3125 5/16 .3150 8.0mm .3160 O .3189 8.1mm .3228 8.2mm .3230 P .3288 8.3mm .3281 21/64 .3307 8.4mm .3320 Q .3346 8.5mm .3386 8.6mm .3390 R .3425 8.7mm

Decimal Drill Size .3438 11/32 .3465 8.8mm .3480 S .3504 8.9mm .3543 9.0mm .3580 T .3583 9.1mm .3594 23/64 .3622 9.2mm .3661 9.3mm .3680 U .3701 9.4mm .3740 9.5mm .3750 3/8 .3770 V .3780 9.6mm .3819 9.7mm .3858 9.8mm .3860 w .3898 9.9mm .3906 25/64 .3937 10.0mm .3970 X .4016 10.2mm .4040 Y .4055 10.3mm .4062 13/32 .4130 Z .4134 10.5mm .4219 27/64 .4252 10.8mm .4331 11.0mm

.4375 7/16 .4409 11.2mm .4528 11.5mm

Decimal Drill Size .4531 29/64 .4646 11.8mm .4688 15/32 .4724 12.0mm .4803 12.2mm .4844 31/64 .4921 12.5mm .5000 1/2 .51 18 13.0mm .5156 33/64 .5312 17/32 .5315 13.5mm .5469 35/64 .5512 14.0mm .5625 9/16 .5709 14.5mm .5781 37/64 .5906 15.0mm .5938 19/32 .6094 39/64 .6102 15.5mm .6250 5/8 .6299 16.0mm .6406 41/64 .6496 16.5mm .6562 21/32 .6693 17.0mm .6719 43/64 .6875 11/16 .6890 17.5mm .7031 45/64 .7087 18.0mm .7188 23/32 .7283 18.5mm .7344 47/64

Decimal Drill Size .7480 19.0mm .7500 3/4 .7656 49/64 .7677 19.5mm .7812 25/32 .7874 20.0mm .7969 51/64 8071 20.5mm .8125 13/16 .8268 21.0mm .8281 53/64 .8438 27/32 .8465 21.5mm .8594 55/64 .8661 22.0mm .8750 7/8 .8858 22.5mm .8906 57/64 .9055 23.0mm .9062 29/32 .9219 59/64 .9252 23.5mm .9375 1516 .9449 24.0mm .9531 61/64 .9846 24.5mm .9688 31/32 .9843 25.0mm .9844 63/64 1.0000 1

Available Sizes(Greater than 17/64" - .2656" diameter)

DECIMAL EQUIVALENT (inch) for Fractional, Number, Letter & Metric

DRILL BITS - SIZE CHARTDRILL BITS - SIZE CHART




Choose high quality CHAMPION or NORSEMAN Brands

Economy HSS Fractional Straight Shank Jobbers Length

• Economical high speed steel for general drilling• Black oxide finish for corrosion resistance• 1 18° point

Economy HSS Fractional 3/8" Reduced Shank Jobbers Length

• Economical high speed steel for general drilling• Black oxide finish for corrosion resistance• 1 18° point • 3/8" reduced shank to fit all 3/8" drills

General Purpose HSS Fractional Straight Shank Jobbers Length

• For general use in metal, wood and plastic• 118° standard point, bright finish

General Purpose HSS Fractional 1/4" Reduced Shank Jobbers Length

• For general use in metal, wood and plastic• 118° standard point, bright finish• 1/4" reduced shank to fit in all 1/4" drills

General Purpose HSS 3/8" Reduced Shank Metal Index SetsDescription Contents15 pc Set 1/16" through 1/2" by 32nds

29 pc Set 1/16" through 1/2" by 64ths

115 pc Super Set 1/16" through 1/2" by 64ths, A through Z, 1 through 60

Empty Metal Index for 60160

HSS Screw Machine Length Fractional

• Also known as "stubbies"• Shorter length for increased strength and rigidity• 135° split point*• Black oxide finish• Ideal for industrial applications

HSS Wire Gauge Screw Machine Length

• Numbered from 1 through 60 (large to small)• Used where more precisely sized holes are required• 135° split point up to and including #42• Drills exact size hole for tapping• Shorter length for increased strength and rigidity

Double End HSS Fractional

• Drills twice as many holes as a single end drill bit• 135° split point • 2" overall length

SELECT 135o SPLIT POINT FOR THE BEST DRILLING PERFORMANCEUSE TO PRE-DRILL MATERIAL FOR INSTALLING SELF-TAPPING SCREWS

DRILL BITSDRILL BITS

HSS Fractional Straight Shank 6" and 12" Aircraft Extension

• Used for drilling in hard-to-reach areas and to run wires and cable.• Use for installing base plates in and retro-fit roof application.• 135° split point* with heavy-duty web

Extra Long Length Drill Bits for Retrofit Roofing and Electrical Applications




Dia. x length Shank 1/8 x 2 1/2 1/8"

3/16 x 3 1/2 3/16" 3/16 x 6 3/16"

1/4 x 4 1/4" 1/4 x 6 1/4 1/4 x 13 1/4 1/4 x 18 1/4"

5/16 x 4 5/16" 5/16 x 6 5/16" 5/16 x 13 5/16"

3/8 x 6 3/8" 3/8 x 13 3/8" 3/8 x 18 3/8" 3/8 x 24 3/8"

1/2 x 6 3/8" 1/2 x 13 3/8" 1/2 x 18 3/8" 1/2 x 24 3/8"

9/16 x 6 3/8"

5/8 x 6 3/8" 5/8 x 8 3/8" 5/8 x 13 3/8" 5/8 x 18 3/8"

3/4 x 6 1/2" 3/4 x 13 1/2"

7/8 x 6 1/2" 7/8 x 13 1/2"

1 x 6 1/2" 1 x 13 1/2"

Regular Duty Straight ShankCarbide Tip Drill Bits Sizes

DRILL BITS - CARBIDE TIPDRILL BITS - CARBIDE TIP




Useable Total PartDia. X Length X Length Number

5/32 x 2 x 4 1/4 AD2195/32 x 4 x 6 1/2 AD220

3/16 x 2 x 4 1/2 AD1043/16 x 4 x 6 1/4 AD2153/16 x 7 x 9 1/2 AD2213/16 x 9 x 11 1/2 AD2163/16 x 13 x 16 AD260

7/32 x 4 x 6 1/4 AD2367/32 x 7 x 9 1/2 AD2377/32 x 9 x 11 1/2 AD2387/32 x 13 x 16 AD265

1/4 x 2 x 4 1/2 AD1051/4 x 4 x 6 1/4 AD1061/4 x 6 x 8 1/2 AD2181/4 x 9 x 11 1/2 AD1831/4 x 13 x 16 AD270

5/16 x 4 x 6 1/4 AD1075/16 x 6 x 8 1/2 AD1085/16 x 10 x 12 1/2 AD222

3/8 x 4 x 6 1/4 AD1093/8 x 8 x 10 1/2 AD1103/8 x 10 x 12 1/2 AD1113/8 x 15 1/2 x 18 AD1123/8 x 19 1/2 x 22 AD239

7/16 x 4 x 6 1/4 AD1137/16 x 10 x 12 AD223

1/2 x 4 x 6 1/2 AD1141/2 x 8 x 10 AD1151/2 x 10 x 12 AD1161/2 x 15 1/2 x 18 AD1171/2 x 21 1/2 24 AD240

9/16 x 4 x 6 1/2 AD1189/16 x 10 x 12 1/2 AD2289/16 x 15 1/2 x 18 AD229

5/8 x 4 x 6 1/2 AD1195/8 x 7 x 9 1/2 AD12O5/8 x 10 x 12 AD1215/8 x 15 1/2 x 18 AD1225/8 x 21 1/2 x 24 AD241

11/16 x 7 x 9 1/2 AD12311/16 x 10 x 12 AD230

3/4 x 7 x 9 1/2 AD1243/4 x 10 x 12 AD1253/4 x 15 1/2 x 18 AD126

7/8 x 7 x 9 1/2 AD1287/8 x 10 x 12 AD1297/8 x 15 1/2 x 18 AD130

1 x 7 x 10 AD1841 x 15-1/2 x 18 AD185

1 1/8 x 7 1/2 x 10 AD2501 1/8 x 15 1/2 x 18 AD255

Special tungsten carbide tips with 1300 tip angles. To take on hardest hitting rotary hammers. To wear down toughest aggregate.

SDS DRIVE

Carbide Tip Drill Bits

Sizes

SDS DRILL BITS - CARBIDE TIPSDS DRILL BITS - CARBIDE TIP




Useable Total Bit PartDia. X Length X Length Style Number

3/8" x 4 x 10 S.C./D.F. AE1313/8" x 7 x 13 S.C./D.F. AE21B

1/2" x 4 x 10 S.C./D.F. AE1321/2" x 7 x 13 S.C./D.F. AE2191/2" x 9 1/2 x 16 S.C./D.F. AE1331/2" x 1 1/2 x 22 S.C./D.F. AE2171/2" x 20 1/2 x 27 S.C./D.F. AE134

9/16" x 7 x 13 S.C./D.F. AE2209/16" x 1 1/2 x 22 S.C./D.F. AE221

5,8" x 4 x 10 AE1365/8" x 7 x 13 AE2225/8" x 9 1/2 x 16 AE1375/8" x 1 1/2 x 22 AE2125/8" x 20 1/2 x 27 AE1385/8" x 30 x 36 AE228

11/16" x 91/2 x 16 AF139

3/4" x 4 x 10 AE1803/4" x 7 x 13 AE2233/4" x 9 1/2 x 16 AE1403/4" x 1 1/2 x 22 AE1413/4" x 20 1/2 x 27 AE1423/4" x 30 x 36 AE229

7/8" x 4 x 10 AE2137/8" x 7 x 13 AE2257/8" x 9 1/2 x 16 AE1437/8" x 15 1/2 x 22 AE1447/8" x 30 x 36 AE230

1" x 4 x 10 AE2141" x 7 x 13 AE2261" x 9 1/2 x 16 AE1451" x 15 1/2 x 22 AE1461" x 30 x 36 AE231

1 1/8" x 9 1/2 x 16 AE1471 1/8" x 15 1/2 x 22 AE148

1 1/4" x 9 1/2 x 16 AE1491 1/4" x 15 1/2 x 22 AE1501 1/4" x 30 x 36 AE232

1 3/8" x 9 1/2 x 16 AE1511 3/8" x 15 1/2 x 22 AE1521 3/8" x 30 x 36 AE233

1 1/2" x 9 1/2 x 16 AE2271 1/2" x 15 1/2 x 22 AE153

1 3/4" x 17 x 22 1/2 AE245

2" x 17 x 22 1/2 AE265

Jet-

Hea

d®

S.C./D.F. = Single cutter with double spiral flute.Jet-Head® design

Carbide Tip Drill Bits

SPLINE DRIVE

Sizes

SPLINE DRILL BITS - CARBIDE TIPSPLINE DRILL BITS - CARBIDE TIP




Diameter Overall Drilling Point Shank Length Depth 3/16" 3/16" 4" 2 3/16" 1/4" 1/4" 5" 3" 5/16" 1/4" 5" 3" 3/8" 1/4" 5" 3" 3/8" 1/4" 8" 6" 7/16" 1/4" 5" 3" 1/2" 3/8" 8" 5" 1/2" 1/2" 18" 14 1/2" 9/16" 3/8" 8" 4 1/2"

RELTON ROTARY ONLY MULTIPLE-CUTTER BITSNon-Removable-Shank, Multiple Cutter BitsConcrete-Termite® Solid Body Style

To Make Overall Diameter Sugg. RPM Shank Dia. Bit Length 7/8" 350-750 1/2" 9" 1" 350-750 1 /18" 350-750 1 1/4" 350-750 1 3/8" 350-750 1/2" 12" 1 1/2’ 350-750 1/2" 18" 1 5/8" 350-750 1/2" 24" 1 3/4" 350-750 2" 250-450 1/2" 9" 2 1/4" 250-450 1/2" 12" 2 1/2" 250-450 1/2" 18" 3" 250-450 1/2" 24"

Removable-Shank Core Bits

Core Body - 4 1/2" OAL, 3 1/2" Core Depth

Will Fit These Core Bit Diameters5/8", 3/4", 7/8", 1", 1 1/8", 1 1/4",

1 3/8" thru 1 5/8", 1 3/4" thru 2 1/4",

2 1/2" thru 3"

E-Z Starter Points for TD Core BitsUse to help keep the core bit from"skipping" across the masonry when first contact is made. The E-Z in-and-out design is quick and simple to use.

Will Fit These Products Thread Size3/4" - 7/8" Hole saws - 1 3/4" 1/2 - 13 to 5/8 - 111" - 4" Hole Saws, 2" and up 3/4 - 10 to 5/8 - 111" - 4" Hole Saws, 2" and up 3/4 - 10 to 1 1/4 - 7

Diamond Drill Rig AdaptersAdapt core bits, rebar cutters and hole saws for use on diamond drill rigs. May be used wet or dry cut.

Diameter Overall Drilling Point Shank Length Depth 5/8" 1/2" 8" 4 1/2" 3/4" 1/2" 8" 4 1/2"

Concrete-Termite® Core Style

REBAR CUTTER - CARBIDE TIPREBAR CUTTER - CARBIDE TIP

Diameter Overall Length Suggested RPMs 3/8" 8" 850-1200 1/2" 12" 850-1200 1/2" 18" 850-1200 9/16" 12" 850-1200 5/8" 12" 750-1000 5/8" 18" 750-1000 1 1/16" 12" 750-1000 3/4" 12" 600-850 3/4" 18" 600-850 3/4" 24" 600-850 13/16" 12" 600-850

Non-Removable-Shank Rebar Cutters

At last, the answer to drilling through concrete-embedded rebar! No more broken or shattered hammer bits; now you can drill through the rebar and not have to relocate the hole to avoid the rebar!

Diameter Overall Suggested Shank To Make Overall Length RPMs Dia. Bit Length 7/8" 600-850 1" 500-750 9" 1 1/8" 500-750 12" 1 1/4" 12" 450-600 1 3/8" 450-600 1/2" 18" 1 1/2" 350-500 24" 1 3/4" 350-500 2" 12" 350-500 9", 12" 2 1/2" 12" 350-500 18", 24"

Removable-Shank Rebar Cutters

Notice: The Relton carbide-tipped rotary rebar cutter is designed for use in standard 1/2" drill motor , but a hammer drill with a standard 3-jaw chuck may be used provided the selector mechanism on the hammer drill is kept in the rotary only position. The Relton carbide-tipped rotary rebar cutter is intended for rotary drilling only; percussion (hammering action) will damage the tool.

Easy As…When rebar is encountered, immediately stop the hammer and remove the bit from the hole, failure to stop immediately will severely damage a carbide hammer bit.

Mount a rotary rebar cutter in a standard 1/2" drill motor or 1/2" hammer drill (with the selector in the rotary-only position); insert the rotary rebar cutter into the hole and drill through the embedded rebar.

Remove the rotary rebar cutter after the rebar has been drilled completely through and finish drilling the hole with the rotary hammer and bit.




Diameter3/4", 7/8", 1". 1 1/8", 1 1/4", 1 3/8", 1

1/2", 1 5/8", 1 3/4", 1 7/8",2", 2 1/8", 2 1/4", 2 3/8", 2 1/2", 2 3/4,

3", 3 1/4", 3 1/2", 4"

Metal Cutting HS Series

1" Drilling Depth StandardComplete saw includes: • Hole saw cutter-head• Shank (HS-S4 or HS-S6)• Pilot ( High-Speed Steel)Will Cut: Carbon Steel, Cast Iron, Stainless Steel, Aluminum

Diameter3/4", 7/8", 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2",

1 5/8", 1 11/16", 1 3/4", 1 15/16", 2", 2 1/8", 2 1/8", 2 1/4", 2 1/2", 3"

Tub, Tile & SpaHST Series

2" Drilling Depth StandardComplete saw includes: • Hole saw cutter-head• Shank (HS-S4 or HS-S6)• Pilot (Carbide tipped)Will Cut: Spas & Hot Tubs, Ceramic Tile, Marble, Gelcoat Fiberglass

Diameter3/4", 7/8", 1", 1 1/8", 1 1/4", 1

3/8", 1 1/2", 1 3/4", 2", 2 1/4", 2 3/8", 2 1/2", 2 3/4, 3", 4"

Interrupted-Cut STHS Series

2" Drilling Depth StandardComplete saw includes: • Hole saw cutter-head• Shank (HS-S4 or HS-S6)• Pilot (High-Speed Steel)Will Cut: Pipe, Trench Duct, Cellular Metal and all types of ferrous and non-ferrous metals where an “interrupted" cut may occur .

RELTON BRAZED CARBIDE HOLE SAWS

Diameter7/8", 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/8", 2 1/4", 2 1/2", 2 3/4", 3", 3 1/2", 4"

Wood/Fiberglass IWHS Series

2" Drilling Depth StandardComplete saw includes: • Hole saw cutter-head• Shank (HS-S4 or HS-S6)• Pilot (High-Speed Steel)Will Cut: PVC, ABS Materials, Composites, Soft Plastic, Fiberglass

Diameter1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1

3/4", 2", 2 1/8", 2 1/4", 2 1/2", 3", 4"

Hard Plastic/Stucco ISHS Series

2" Drilling Depth StandardComplete saw includes: • Hole saw cutter-head• Shank (HS-S4 or HS-S6)• Pilot (Carbide Tipped)Will Cut: Dry Lath & Plaster, Stucco, Wood with Nails,Aluminum Siding, Hard or Composite Plastic

Hole Saw Shank SpecificationsHS-S4 Series Shanks3/4-10 threads, 3/8" Pilot hole, 1/2" round shank w/ 3 flats,HS-S6 - 3" OAL Wt. 0.5HS-S67 - 7" OAL Wt. 0.8HS-S610 - 10" OAL Wt. 1.2

S-12 Shank1/2-13 threads, 1/4" Pilot hole, 3/8" round shank w/ 3 flats,3" OALWt. 0.4

HS-S4 Series Shanks3/4-10 threads, 1/4" Pilot hole, 1/2" round shank w/ 3 flats,HS-S4 - 3" OAL Wt. 0.5HS-S47 - 7" OAL Wt. 0.8HS-S410 - 10" OAL Wt. 1.2

HOLE SAWS HOLE SAWS




7 piece carbide tipped job saver kit 7/8", 1", 1 1/8", 1 1/4", 1 1/2" sizes. Arbor No. 49-56-6951, Arbor spacer No. 49-67-0120, Arbor adapter No. 49-56-6560 and sturdy plastic case. Plastic case only 48-55-0783

7 piece 4/6 tooth job saver kit 7/8", 1", 1 1/8", 1 1/4", 1 1/2" sizes. Arbor no. 49-56-6950, Arbor spacer No. 49-67-0120, Arbor adapter no. 49-56-6560 and sturdy plastic case. Plastic case only 48-55-0782

13 piece plumber’s and electrician’s kit 3/4", 7/8", 1 1/8", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/4", 2 1/2" sizes. Arbor nos. 49-56-6950, 49-56-7140, pilot drill no. 49-56-8000, arbor spacer no. 49-67-0120, arbor adapter no. 49-56-6560 and sturdy plastic case. Plastic case only 48-55-0781

17 piece deluxe electrician’s kit 5/8", 3/4", 7/8", 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/2", 3" sizes. Arbor nos. 49-56-7000, 49-56-7140, 3 pilot drills no. 49-56-8000 and sturdy plastic case. Plastic case only 48-55-0784

17 piece 4/6 tooth deluxe electrician’s kit 5/8", 3/4", 7/8", 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/2", 3" sizes. Arbor nos. 49-56-7000, 49-56-7140, 3 pilot drills no. 49-56-8000 and sturdy plastic case. Plastic case only 48-55-0784

13 piece 4/6 tooth piece plumber’s and electrician’s kit 3/4", 7/8", 1 1/8", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/4", 2 1/2" sizes. Arbor nos. 49-56-6950, 49-56-7140, pilot drill no. 49-56-8000, arbor spacer no. 49-67-0120, arbor adapter no. 49-56-6560 and sturdy plastic case.

Plastic case only 48-55-0781

13 piece 4/6 tooth contractor’s kit 3/4", 7/8", 1", 1 3/8", 1 1/2", 1 3/4", 2", 2 1/8", 2 1/2" sizes. Arbor nos. 49-56-6950, 49-56-7140, pilot drill No. 49-56-8000, arbor spacer no. 49-67-0120, arbor adapter no. 49-56-6560 and sturdy plastic case.


Hole saw door lock installation kit Consists of 1" and 2 1/8" 4/6 tooth hole saw, 3/8" hex arbor, arbor spacer and arbor adapter.

Hole saw arbor service kit Spring, ball and screws necessary for replacement on arbor nos. 49-56-7130, 49-56-7140 and 49-56-7150.

Hole saw arbor service kit Consists of springs, screws, ring and pins necessary for replacement on arbor no. 49-56-7055.

8 piece electrician’s kit 7/8", 1 1/8", 1 1/2", 1 3/4", 2", 2 1/2" sizes. Arbor nos. 49-56-7000, 49-56-7140 and steel case. Steel case only 48-55-0760

7 piece carbide tipped job saver kit 7/8", 1", 1 1/8", 1 1/4", 1 1/2" sizes. Arbor No. 49-56-6950, arbor spacer no. 49-67-0120, arbor adapter no. 49-56-6560 and sturdy plastic case.


HOLE SAW KITS - MILWAUKEEHOLE SAW KITS - MILWAUKEE




Hole Shank Size Max. 3/8" 7/8"



Hole Hole Step Shank Size Max. Size Min. Increments Thickness 3/8" 7/8" 3/16" 1/16" 1/8"

Hole Hole Shank Size Max. Size Min. 3/8" 1 1/8", 7/8" 1/4"

Hole Hole Step Shank Size Max. Size Min. Increments Thickness 1/4" and 3/8" 1" 1/8" 1/32 - 1/16" 1/8"

1/4" shank, 13 hole sizes, make this the perfect all-around bit for most common drilling jobs

Hole Hole Step Shank Size Max. Size Min. Increments Thickness 1/4" 1/2" 1/8" 1/32" 1/8"

48-89-9105 Self-Starting Multi-Hole Bit Hole Hole Step

Shank Size Max. Size Min. Increments Thickness 3/8" 3/4" 1/4" 1/16" 1/8"

48-89-9110 Hole Enlarging Bit Hole Hole Step

Shank Size Max. Size Min. Increments Thickness 3/8" 1" 9/16" 1/16" 1/8"

48-89-9115 Self-Starting Knockout

48-89-9120Self-Starting Knockout

48-89-9125Self-Starting Knockout

48-89-9130Self-Starting Multi-Hole Bit

48-89-9135Self-Starting Combination Knockout

48-89-9100 Self-Starting Multi-Hole Bit

3/8" shank, 9 hole sizes, make this a good choice for medium size holes.

3/8" shank, 9 hole sizes, make this the companion to 48-89-9100. Requires 1/2" or larger pilot hole.

3/8" shank, drills 7/8" knockouts quickly and easily . Use for draw bolt holes, for large knockouts and miniature pilot holes.

1/4" shank, 1/2" hole. Use for auto body jobs and electrical panel work.

1/4" shank, 1/2" hole. Use for auto body , electrical panel work and many other uses.

3/8" shank, 1/2" hole size bit perfect for knockouts.

3/8" shank, 3 hole size bit gives increased flexibility for knockout pilots.

48-89-9050Set of two step drill bitsIncludes 48-89-9100 and 48-89-9110. Gives a range of diameters 1/8" to 1".

STEP DRILL BITS - MILWAUKEESTEP DRILL BITS - MILWAUKEE




BUILT FOR THE JOB SITE. The series 20™ saw blade line includes a full range of thin-kerf blades for long life on the job. Built for durability in the toughest job site applications.

MITER/SAW BLADES

General Purpose DW3103, DW3114

For all-purpose cutting in natural wood, plywood and wood

composites.

Fine Crosscuts DW3126, DW3128For fine crosscuts in natural

wood, plywood and wood composites.

Pressure Treated / Wet Lumber DW3104Anti-stick coating reduces buildup

on the blade when cutting pressure treated or wet lumber.

Diameter Arbor Plate Cat # (inches) (inches) Teeth (inches) DW3103 10" 5/8" 32 .071 DW31 14 10" 5/8" 40 .071

DW3126 12" 1" 60 .071 DW3128 12" 1" 80 .071

DW3104 10" 5/8" 32 .071

PORTABLE CONSTRUCTION SAW BLADES

Combination FramingDW3171,DW3178, DW3176, DW3182,

DW3184For all-purpose cuts in natural wood,

plywood and wood composites.

HardiPlank® Fiber Cement

DW3193For fine crosscuts in natural

wood, plywood and wood composites.

Pressure Treated / Wet Lumber

DW3174Anti-stick coating reduces buildup

on the blade when cutting pressure treated or wet lumber..

Diameter Arbor Plate Cat # Bulk # (inches) (inches) Teeth (inches) DW3171 DW3571 7-1/4" 5/8" 16 045 DW3178 DW3578 7-1/4" 5/8" 24 .045 DW3176 DW3576 7-1/4" 5/8" 36 .045 DW3182 DW3582 8-1/4" 5/8" 24 .050 DW3184 – 8-1/4" 5/8" 40 050

DW3174 DW3574 7-1/4" 5/8" 18 .045

DW3193 – 7-1/4" 5/8" 6 PCD .063

CORDLESS SAW BLADES - 6 1/2" DIAMETER

Fast Cutting DW9155

Framing DW9154

Aluminum DW9154

Combo (DW9155, DW9154) DW9158

Diameter Arbor Plate Cat # (inches) (inches) Teeth (inches) DW9155 6-1/2" 5/8" 16 .039

DW9154 6-1/2" 5/8" 24 .039

DW9152 6-1/2" 5/8" 36 .039

DW9158 6-1/2" 5/8" 16/24 .039

SAW BLADES - CIRCULARSAW BLADES - CIRCULAR




FAST CLEAN CUTS IN METALDewalt Metal Cutting Blades provide clean, fast cuts in a variety of ferrous, non-ferrous and stainless steel materials. Specially designed carbide teeth deliver precise, virtually burr-free cuts and produce cut material that is cool to the touch.

12% titanium carbideprovides long life in metal cuttingModified ATB tooth geometry provides clean, burr free cutsTri-fold braze absorbs stressmaking the tip strongerExpansion slots dissipate heat which extends blade life

Heavy Gauge Metal

DW7747

Stainless Steel

DW7749

Thin Gauge Metal

DW7745

Diameter Arbor Plate Cat # (inches) (inches) Teeth (inches, mm) DW7747 14" 1" 70 .071, 1.8

DW7745 14" 1" 90 .071, 1.8

DW7749 14" 1" 90 .071, 1.8

Always clamp material securely Cut forward of the blade center line and never cut bundles

SAW BLADES - CIRCULARSAW BLADES - CIRCULARMETAL CUTTINGMETAL CUTTING




Concrete C30UBHeavy DutyThe contractors’ choice for all-around performance when cutting concrete and masonry products, including brick, block and pipe. Also cuts PVC and ductile iron pipe (for best results on ductile, see Specialist AC24SB-Ductile,Cast Iron listed below).

Steel A24/30SBHeavy DutyA durable, hard working blade for a variety of metal cutting applications on the job site. Excellent for rebar, steel pipe, sheet metal, and structural steel or stainless.

SPECIALISTSPECIALISTSPECIALIST ®

TYPE1 HIGH SPEED GAS & ELECTRIC SAW WHEELS FOR CUTTING ONLY

Use onHigh Speed

Saws• Maximum Productivity• Exceptional Value• State Of The Art Engineering

Type 1

• Job Focused• Peak Performance

Heavy DutyDimensions Max Metal Concrete BoxDia. X Thck X Arbor RPM A24/30SB C30UB Qty.12" X 1/8" X 20 mm 6,300 F5078 L5315 10

12" X 1/8" X 7/8" 6,300 F5286 L5316 10

12" X 1/8" X 1" 6,300 F5292 L5317 10

14" X 1/8" X 20 mm 5,460 F5653 L5703 10

14" X 1/8" X 7/8" 5,400 F5650 L5708 10

14" X 1/8" X 1" 5,400 F5687 L5727 10

Sheet Metal, DeckingA24TB-Long LifeBuilt to withstand the wear of sharp metal edges, this blade stands up to sheet metal, roof decking, and cut dismantling jobs.

RailTrackA30PB-Extra Fast CutDesigned for rail cropping. Straight, fast cuts on all sizes and weights of rail.

Ductile, Cast IronAC24SB-Heavy DutyFor sewer and water construction and maintenance. Cuts ductile iron, cast iron and concrete lined pipe.

Asphalt, Green ConcreteC16UB-Long LifeMade of extra coarse silicone carbide, C16UB provides aggressive free cutting action, in a wide range of aggregates.

Prestressed ConcreteC30SB-Heavy DutyDesigned for extra fast cutting in prestressed concrete.

Sheet Metal Rail Track Ductile Asphalt Prestressed Decking Extra Cast Iron Gr. Concrete Concrete Dimensions Max Long Life Fast Cut Heavy Duty Long Life Heavy Duty BoxDia. X Thk X Arbor RPM A24TB A30PB AC24SB C16UB C30SB Qty12" X 1/8" X 20 mm 6,300 L5017 10 L5310 10

12" X 1/8" X 7/8" 6,300 L5018 10

12" X 1/8" X 1" 6,300 F5098 10 L5019 10

12" X 5/32" X 20 mm 6,300 F5293 10 L5330 10

12" X 5/32" X 7/8" 6,300 F5299 10 L5332 10

12" X 5/32" X 1" 6,300 F5314 10 L5334 10

14" X 1/8" X 20 mm 5,460 L5617 10

14" X 1/8" X 7/8" 5,400 L5618 10

14" X 1/8" X 1" 5,400 F5681 10 L5619 10

14" X 5/32" X 20 mm 5,460 F5693 10 L5710 10

14" X 5/32" X 1" 5,400 F5614 10 L5712 10

16" X 1/8" X 1" 4,500 F6681 10

ABRASIVE WHEELS - HIGH SPEEDABRASIVE WHEELS - HIGH SPEEDCUTTINGCUTTING




Metal, StainlessA30S-Fast GrindingAggressive grinding with good life. The A30S performs well on a broadrange of metals, including stainless and other hard alloys. An excellent“all-purpose" grinding spec.

TYPE 27 DEPRESSED CENTER GRINDING WHEELS FOR GRINDING ONLY

• Maximum Productivity• Exceptional Value• State Of The Art Engineering

Use onAngle Grinders

Type 27

Type 27 Spin-On

Max Metal, Stainless Concrete Dimensions RPM Fast Grind Heavy Duty Heavy Duty Box/Crt.Dia. X Thk. X Arbor A30S S24/30T C24/30P Qty.3" X 1/4" X 3/8" 20,000 A0054 25/100

4" X 1/4" X 3/8" 15,000 A0414 25/100 A0406 25/100

4" X 1/4" X 5/8" 15,000 A0414 25/100 A0406 25/100 A0396 25/100

4-1/2" X 1/4" X 7/8" 13,300 A1236 25/100 A1226 25/100 A1257 25/100

4-1/2" X 1/4" X 5/8"-11 13,300 A1236H 10 A1226H 10 A1257H 10

5" X 1/4" X 7/8" 12,000 A2236 25/1000 A2226 25/100 A2239 25/100

5" X 1/4" X 5/8"-11 12,000 A2236H 10 A2226 10 A2239H 10

6" X 1/4" X 7/8" 10,000 A3236 25

6" X 1/4" X 5/8"-11 10,000 A3236H 10

7" X 1/4" X 7/8" 8,600 A5356 25 A5301 25 A5446 25

7" X 1/4" X 5/8"-11 8,600 A5356H 10 A5301H 10 A5446H 10

7" X 5/16" X 7/8" 8,600 A5551 25

9" X 1/4" X 7/8" 6,800 A8353 25 A8301 25 A8446 25

9" X 1/4" X 5/8"-11 6,800 A8353H 10 A8301H 10 A8446H 10

9" X 5/16" X 7/8" 6,800 A8619 25

A24/30T-Heavy DutyOften copied, but never equaled, A24/30T is the most rugged wheel in the industry. Flexovit’s A24/30T delivers the longest life of any aluminum oxide wheel without sacrificing aggressive grinding action. Your best choice for tough applications such as beveling and edge or flame cut grinding. This durable wheel can dramatically reduce your abrasive cost.

ConcreteC24/30P-Heavy DutyMa de with silicone carbide grain, C24/30P is designed for all concrete and masonry applications. Also offers fast grinding action on non ferrous metals.

ABRASIVE WHEELS ABRASIVE WHEELS GRINDINGGRINDING




When cutting stainless or other hard alloys, or for gettingthrough large solids without bogging down in the cut, use this exceptionally fast cutting specification.

Drywall StudA30TB-Clean CutStands up to the wearing action of sharp metal edges. Thiswheel cuts more drywall bundles per dollar than any otherproducts.

An optimum mix of cutting speed and wheel life makes thisan excellent “general purpose" wheel for profiles and solidsin carbon or alloy steels.

A30SB-Long LifeExtended wheel life, particularly for lighter gage cutting insteel and alloys.

C30UB-Heavy DutyExcellent for cutting tiles, concrete blocks and brick.

TYPE 1 CHOP-SAW / MITER-SAW WHEELS FOR CUTTING ONLY

SPECIALISTSPECIALISTSPECIALIST ®

Use OnChopsaws

• Maximum Productivity• Exceptional Value• State-of-the-Art Engineering

Type 1

Type 1

• Job Focused• Peak Performance

Metal, Stainless Concrete

Dimensions Max Fast Cut Long Life Heavy Duty BoxDia. X Thk. X Arbor RPM A30RB A30SB C30UB Qty.10" X 3/32" X 5/8" 6,112 F3579 10

10" X 1/8" X 5/8" 6,112 F3941 L3818 10

12" X 3/32" X 1" 5,092 F4808 10

12" X 3/32" X 1" 5,092 F4818 10

14" X 3/32" X 1" 4,365 F5521 10

14" X 3/32" X 1" 4,365 F5527 10

16" X 3/32" X 1" 3,820 F6521 10

Stainless Drywall Stud Dimensions Max Fast Cut Clean Cut, Max Life BoxDia. X Thk. X Arbor RPM A30QB A30TB Qty.12" X 3/32" X 1" 5,092 F4819 10

14" X 3/32" X 1" 4,365 F5523 10

14" X 3/32" X 1" 4,365 F5528 10

16" X 3/32" X 1" 3,820 F6579 10

ABRASIVE WHEELS - CHOP SAW ABRASIVE WHEELS - CHOP SAW CUTTINGCUTTING

Metal, StainlessA30RB-Fast Cut

StainlessA30QB-Free Cut




Ferrous and/or Non-Ferrous Metals (Iron, Steel, W elds, etc.).

A60S

• Thin .045 Width• Special Aluminum Oxide Grain• Hard Bond for Extremely Long Life• Fast, Burr-Free Cutting

DEPRESSED CENTER .045 CUTTING WHEELS TYPE 27

Non-Ferrous Metals (Aluminum, Copper, Brass, etc.).

A46N Aluminum(Non-Ferrous Metals)

• Aluminum Oxide Grain• Thin .045 Width• Soft Bond for Aggressive Cutting Without Loading

Wheels can be mounted to right angle grinders with standard T ype 27 flanges

Note: Reusable 5/8"-11 adapter for use on Type 1 and Type 27 reinforced wheels with a 7/8" arbor , a maximum diameter of 5" and a wheel thickness of .045 to 1/8" available.

Size A B C Max Qty. Qty. Lbs.Dia. Width Bore RPM Per Box Per Ctn. Per Box 4" .045 5/8" 19,000 50 200 4

4-1/2" .045 7/8" 13,300 50 200 4

5" .045 7/8" 12,200 50 200 6

6" .045 7/8" 10,200 50 200 8

7" .045 7/8" 8,500 50 200 14

ABRASIVE WHEELS ABRASIVE WHEELS CUTTINGCUTTING

Use onAngle Grinders

A60S

• Thin .045 Width• Use With Reusable 5/8"-11 Adapter to Fit Right angle Grinders• Extremely Fast Cutting With Long Life

.045 HIGH SPEED CUT-OFF WHEELS TYPE 1

Ferrous and/or Non-Ferrous Metals (Iron, Steel, W elds, etc.).

Non-Ferrous Metals (Aluminum, Copper, Brass, etc.).

A46N Aluminum(Non-Ferrous Metals)• Aluminum Oxide Grain• Soft Bond for Aggressive Cutting Without Loading• Use With Reusable 5/8"-11 Adapter to Fit Right Angle Grinders

Size A B C Max Qty. Qty. Lbs.Dia. Width Bore RPM Per Box Per Ctn. Per Box 4" .045 5/8" 19,000 50 200 4

4-1/2" .045 7/8" 13,300 50 200 4

5" .045 7/8" 12,200 50 200 6

6" .045 5/8" 10,200 50 200 8

6" .045 7/8" 10,200 50 200 8

7" .045 5/8" 8,500 50 200 14




Cured Concrete Blades

Premium Black (P) • .250 diamond depth.• A high quality blade that delivers long lasting, fast cutting performance.• Designed for contractors who demand maximum ef ficiency and value.Heavy Duty Orange (H)• .236" diamond depth• Fast cutting blade that works well with a wide variety of high or low h.p.

saws.• Combines long life performance while maximizing your blade dollars.Standard Gold (S)• .187 diamond depth.• Economical blades that work well for contractors who don’t have a heavy

volume of cutting to be done. • Delivers the speed and convenience of a diamond blade compared with

conventional abrasive blades that require frequent blade changes.

10" x .110

10" x .125

12" x .110

12" x .125

12" x .140

12" x .155

12" x .187

12" x .250

12" x .375

14" x .110

14" x .125

14" x .140

14" x .155

14" x .175

14" x .187

14" x .250

14" x .375

16" x .125

16" x .140

16" x .155

16" x .187

16" x .250

18" x .125

18" x .140

18" x .155

18" x .165

18" x .175

18" x .187

18" x .210

18" x .250

20" x .125

20" x .140

20" x .155

20" x .187

20" x .250

24" x .140

24" x .155

24" x .165

24" x .175

24" x .187

24" x .210

24" x .250

25" x .155

26" x .155

26" x .165

26" x .175

26" x .187

26" x .210

26" x .250

28" x .187

30" x .175

30" x .187

30" x .210

30" x .250

32" x .175

32" x .187

32" x .210

32" x .250

36" x .175

36" x .187

36" x .210

36" x .250

42" x .187

42" x .210

42" x .220

48" x .210

48" x .250

54" x .220

60" x .220

Available Sizes(diameter x thickness)

X Slant Seg. Protection

No extra charge on any blade. Used on cured concrete, standard asphalt and green blades when undercutting conditions are occurring.

R Full Radius Protection

Low cost undercut protection for average undercutting situations.

Q Insert Protection

Our most popular, maximum wear retardant protection used in tough undercut conditions across North America.

Optional Types of Undercut Protection

Cured Concrete Specs (Application Code C)

Select Grade S Standard (Gold) Most concrete blades are H Heavy Duty (Orange) laser welded. Any concrete P Premium (Black) blade can be laser welded or silver brazed upon request.* These are recommendations for starting specifications.

Aggregate Type Spec. #* Aggregate Type Spec. #* (Heavy Reinforcement) Hard 51W Hard 51W Medium Hard 52 Medium Hard 52 Medium 56 Medium 52 Medium Soft 60 Med. Soft 56 Soft 62 Soft 56

CONCRETE SAWING BLADESCONCRETE SAWING BLADES




DRY TUCK POINT BLADES

ELECTRIC SAW BLADES

Size Catalog No.4" x .250 124184 1/2" x .250 124295" x .250 124377" x .250 124468" x .250 12454

Application Utility Yellow Econ. Green Std. Gold HD Orange HP Stag. Seg..General purpose YT4000 DT4000 DT9S DT9H ----

Long lifehigh performance ---- ---- ---- ---- HPTD9H

DT9H HD Orange General Purpose

Size Catalog No.4" x .250 12462 4 1/2" x .250 12466 5" x .250 12470 7" x .250 12475 8" x .250 12476

DT9S Standard Gold General Purpose

Size Catalog No.4" x .250 116974 1/2" x .250 116985" x .250 117007" x .250 117028" x .250 16638

HPDT9H High Performance

Staggered Segment

SPECIFICATIONS

Premium Black Small Diameter Dry Blades

E2P E5P SIZE Catalog No. Catalog No.4" x .070 11304 113054 1/2" x .070 11307 113085" x .080 11310 113115 1/2" x .080 18197 113126" x .080 11315 113167" x .080 11319 113228" x .080 11338 113399" x .080 11340 11342

diameter and thickness

diameter and thickness

CONCRETE SAWING BLADESCONCRETE SAWING BLADES

WET CORE BITSAvailable Sizes (diameter)Premium bits: 1/2", 5/8", 3/4", 7/8" 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1 3/4", 1 7/8", 2", 2 1/4", 2 1/2",2 3/4", 3", 3 1/4", 3 1/2", 4", 4 1/4", 4 1/2", 5", 5 1/2", 6", 6 1/4", 6 1/2", 7", 8", 9", 10", 12", 14",16", 18", 20", 24"

Heavy duty bits: 1/2", 5/8", 3/4", 7/8" 1", 1 1/8", 1 1/4", 1 3/8", 1 1/2", 1 5/8", 1 3/4", 1 7/8", 2", 2 1/4", 2 1/2", 2 3/4", 3", 3 1/4", 3 1/2", 4", 4 1/4", 4 1/2", 5", 5 1/2", 6", 6 1/4", 6 1/2", 7", 8", 9", 10", 12", 14",16", 18", 20", 24"

Ordering information

1. Segmented bits available in soft, medium and hard bonds.2. All bits may be ordered with custom bonds.

Standard bit length is 13" on 1/2" through 12" bits. Any length available upon request 1/2" to 1 1/2" = 5/8" - 1 1 threaded hub. 1 5/8" and up = 1 1/4" - 7 hub.Note: All diameters are nominal. Exact tolerances upon request.

DRY HOLE SAWS Drill/GrinderDiameter Catalog Drill/Grinder Max. RPM/ Number Minimum Amps Min. RPM7/8" 04771 6 6000/23001" 04706 6 6000/23001 1/4" 04711 6 6000/23001 1/2" 04717 7 5000/18001 3/4 04720 7 5000/16002" 0001 1 7 5000/12002 1/4 04727 7 5000/12002 1/2" 00012 7 5000/12003" 00013 7 5000/8003-1/2" 00014 10 5000/8004" 04745 10 5000/7004 1/2" 04751 10 5000/7005" 04756 10 2500/7006" 04764 10 2500/800

DH bits come with 5/8" - 11 thread and 9" drilling depth standard. Not all types of brick and block can be drilled. Please consult the factory .




BI-METAL RECIPROCATING BLADES

T eeth Per Length Recommended for cutting Inch (In.) 5/8 6 6 6 Very fast cutting, nail embedded wood, general Rough-in. 6 9 6 12 6 6 Fast cutting, all woods, nail embedded, composition material.

14 3 5/8 Scroll cutting metal 3/16" thru 1/4".

18 3 5/8 Scroll cutting metal 1/8" thru 3/16". 14 4 Metal 3/16" thru 1/4", conduit, tubing, channels, pipe, rubber , fiber. 14 6 18 4 Metal 1/8" thru 3/16", conduit, tubing, channels, pipe. 18 6 24 4 Metal thinner than 1/8", tubing, pipe, trim. 24 6

10 4 All woods, nail embedded, composition material, plastic and non-ferrous metals. 10 6 10/14 8 All woods, nail embedded, composition material, plastic, non-ferrous metals and cast iron. 10/14 12

We stock a full line of professional brand reciprocating saw blades to handle any application!

METAL CUTTING Reinforced tooth design provides increased durability.

Matrix II steel with 8% cobalt on the cutting edge provides flexibility to minimize breakage.

Specially formulated anti-stick coating minimizes friction and gumming

WOOD CUTTING Reinforced tooth for increased durability when cutting through nails and other foreign objects.

+6 degree hook angle for fast, aggressive cuts.

Anti-stick coating minimizes friction and gum-up.

Raker tooth design keeps the blade in the cut thereby minimizing vibration.

DEMOLITION Demolition blades are thicker than standard blades thereby preventing breakage.

Wider blades add more stability to the cut making it easier to cut a straight line.

Reinforced teeth for increased durability.

Specially formulated anti-stick coating minimizes friction and gum-up for smoother cuts.

TILEMedium carbide grit offers the ability to cut in hard materials.

RECIPROCATING SAW BLADESRECIPROCATING SAW BLADES




RECIPROCATING SAW BLADES

Teeth Length x Width Per Inch x Thickness Recommended for cutting 5/8 6 x 1.0 x .062 Excellent for plunge cutting into wood and nail embedded wood without bending blades. 5/8 9 x 1.0 x .062 Cut into walls that contain wood, nails, plaster and aluminum 5/8 12 x 1.0 x .062 Great for demolition work. Extra long demolition blade.

10 6 x 1.0 x .042 10 9 x 1.0 x .042 14 6 x 1.0 x .042 Metal pipe, channels, tubing, 14 9 x 1.0 x .042 angle iron up to 4", steel, 18 6 x 1.0 x .042 nail-embedded wood. 18 9 x 1.0 x .042 18 12 x 1.0 x .042

8 5.5 x 1.0 x .062 8 8 x 1.0 x .062 8 12 x 1.0 x .062 Metal pipe, channels, 10 6 x 1.0 x .042 tubing, angle iron up to 4", 10 9 x 1.0 x .042 steel, nail-embedded wood. 14 6 x 1.0 x .042 14 9 x 1.0 x .042 14 12 x 1.0 x .042

T ype Grit COARSE GRIT 4 x 3/4 x .032 Medium and coarse grits for cutting hardwood flooring, cast iron, MEDIUM GRIT 3-1/2 x 1/2 x .032 stainless steel, fiberglass materials (polyesters, epoxies, COARSE GRIT 6 x 3/4 x .032 melamine, ceramic tile, stone, slate, clay pipe COARSE GRIT 9 x 3/4 x .039 carbon, brick, plaster, marble and chalkboard.

T.P.I. Recommended for cutting 6 4 x 3/4 x .050 Fast cutting, all woods, nail 6 6 x 3/4 x .050 embedded, composition materials.

5/8 6 x 3/4 x .050 Very fast cutting, nail embedded 6 6 x 3/4 x .050 wood, general Rough-in. 6 9 x 3/4 x .050 Very fast scroll cutting, 6 12 x 3/4 x .050 circles, contours, 4/6 6 x 1/2 x .050 nail embedded wood.

6 6 x 3/4 x .050 Fleam filed teeth for extremely 6 9 x 3/4 x .050 sharp, fast cutting with a smooth 6 12 x 3/4 x .050 edge in nail free wood and plastics. 6 6 x 3/4 x .050 Scroll cutting nail free wood and plastics.

6 5 x 3/4 .050 Long life, plaster, plaster with metal lath, plasterboard. Cuts forward & backward stroke.

10 4 x 3/4 x .035 All woods, nail embedded, composition material, 10 6 x 3/4 x .035 plastic, ferrous and non-ferrous metals. 8/12 6 x 3/4 x .050 8/12 8 x 3/4 x .050 All woods, nail embedded, composition material plastic, ferrous and, non-ferrous 8/12 12 x 3/4 x .050 metals, cast iron. All woods, nail embedded, composition material, plastic, light gauge 10/14 8 x 5/8 x .035 non-ferrous metals and aluminum. Has 5/8" width for higher flexibility . 10/14 12 x 5/8 x .035

10 3 5/8 x 5/16 x .035 Scroll cutting wood, contours, nail embedded wood, plastics. 14 3 5/8 x 5/16 x .035 Scroll cutting metal 1/8" thru 3/16". 18 3 5/8 x 5/16 x .035 Scroll cutting metal under 1/8".

14 4 x 3/4 x .035 14 6 x 3/4 x .035 Metal 3/16" thru 1/4", conduit, tubing, channels, pipe, rubber , fiber. 14 6 x 5/8 x .035 Has 5/8" width for higher flexibility.

14 9 x 3/4 x .035 Metal 3/16" thru 1/4", conduit, tubing, channels, pipe, rubber , fiber. 18 4 x 3/4 x .035 Metal 1/8" thru 3/16", conduit, tubing, channels, pipe. 18 6 x 3/4 x .035 18 6 x 5/8 x .035 Same as 48-01-5184, but has 5/8" width for higher flexibility . 18 9 x 3/4 x .035 Metal 1/8" thru 3/16", conduit, tubing, channels, pipe. 18 12 x 3/4 x .035 24 4 x 3/4 x .035 24 6 x 3/4 x .035 Metal thinner than 1/8", tubing, pipe, trim. 24 6 x 5/8 x .035 Has 5/8" width for higher flexibility.

RECIPROCATING SAW BLADESRECIPROCATING SAW BLADES




LOCKING PLIERS - VISE GRIPLOCKING PLIERS - VISE GRIP




HAND SNIPS - IRWIN HAND SNIPS - IRWIN




Compact

Phillips Bit Tip #1 Phillips Bit Tip #2 Phillips Bit Tip #3

Slotted Bit Tip #8 Slotted Bit Tip #10 Slotted Bit Tip #12

Square Recess Bit Tip #1 Square Recess Bit Tip #2 Square Recess Bit Tip #3

Pozi-driv ® Bit Tip #1 Pozi-driv ® Bit Tip #2 Pozi-driv ® Bit Tip #3

T orx® Bit Tip T10 T orx® Bit Tip T15 T orx® Bit Tip T20 T orx® Bit Tip T25 T orx® Bit Tip T27 T orx® Bit Tip T30 T orx® Bit Tip T40

1" Bit Tips

Phillips #2 / Slotted #8 Phillips #2 / Phillips #2 Phillips #2 / Square Recess #2

Double Ended Bits

2" Phillips Power Bit #1 2" Phillips Power Bit #2 2" Phillips Power Bit #3 Deck Power Bit #2

2" Square Recess Power Bit #1 2" Square Recess Power Bit #2 2" Square Recess Power Bit #3

3-1/2" Phillips Power Bit #1 3-1/2" Phillips Power Bit #2 3-1/2" Phillips Power Bit #3

3-1/2" Slotted Power Bit #6 3-1/2" Slotted Power Bit #8 3-1/2" Slotted Power Bit #10 3-1/2" Slotted Power Bit #12

3-1/2" Square Recess Power Bit #1 3-1/2" Square Recess Power Bit #2 3-1/2" Square Recess Power Bit #3

6" Phillips Power Bit #1 6" Phillips Power Bit #2 6" Phillips Power Bit #3

6" Slotted Power Bit #6 6" Slotted Power Bit #8 6" Slotted Power Bit #10 2" Square Recess Power Bit #6 2" Square Recess Power Bit #8 2" Square Recess Power Bit #10

Power Bits

Magnetic Drive Guides

Magnetic Socket DriversDescription Size LengthMagnetic hex socket 1/4" 1-7/16"Magnetic hex socket 5/16" 1-7/16"Magnetic hex socket 3/8" 1-1/2"Magnetic hex socket 1/4" 2-9/16"Magnetic hex socket 5/16" 2-9/16"Magnetic hex socket 3/8" 2-9/16"

Description Size LengthEyelag socket driver 2-9/16"

Depth sensing for drywall installation. Magnetic

Screw-driving Set

1" Phillips Bit Tips: (1) #1, (10) #2, (1) #31" Slotted Bit Tips: (1) #6, (2) #8, (1) #101" Square Recess Bit Tips: (1) #1, (6) #2, (1) #32" Phillips Power Bit: (1) #22" Square Recess Power Bit: (1) #2Nutdrivers: (1) 1/4", (1) 5/16"Compact magnetic drive guide (1)

Magnetic Drive Guides (2)1" Phillips Bit Tips: (1) #1, (1) #21" Slotted Bit Tips: (1) #8-101" Square Recess Bit Tip: (1) #2

29 Piece Set

TOOL ACCESSORIESTOOL ACCESSORIES

Bit Holders

QuickChangeMagnetic

MagneticHolder

Description Size LengthMagnetic Bit Holder 1/4" Drive 1-5/8" 2-1/4" 2-3/4" 3"

Length 2 3/8"

Special adjustable sleeve stabilizes the fastener during installation

Standard

Clear




WE STOCK A FULL LINE OF HAND TOOLS FOR COMMERCIAL ROOFING AND METAL BUILDING APPLICATIONS.

HAND TOOLSHAND TOOLS

SPUD WRENCHES AND PRY BARSGreat for aligning holes for bolted joint connections

HAMMERSSelect from a wide variety.

SHOVELSGreat for roofing and miscellaneous job site application.

SCREW DRIVERSPhillips / Cross Recess, Slotted, Square,TORX / Six-Lobbed, Nut Drivers

SOCKETSImpact for bolted joint connections. 12pt and 6pt.

BROOMSRoofers broom for applying asphalt.

BRUSHESHigh quality for applying asphalt in roofing application.




LEVELS AND LASERSLEVELS AND LASERS

LEVELSChoose from journeyman, torpedo or a magnetic level for steel framing applications.

WE STOCK A FULL LINE OF LEVELS, LASERS, AND MEASURING TOOLS TO ASSURE PRECISE LEVEL, PLUMB, SQUARE AND DISTANCE.

LASERSThe best brands available for level, plumb, square and distance.

MEASURING TAPESWe stock a wide range of styles and lengths up to 25 feet.

CHALK LINESProfessional grade for commercial construction applications.




WE STOCK A FULL LINE OF UTILITY KNIVES AND REPLACEMENT BLADES.

HAND TOOLSHAND TOOLS




LEVELS AND LASERSLEVELS AND LASERS

WE CARRY A VARIETY OF LADDERS , PLATFORMS AND DRYWALL CARTS.

Contact us for the best brands and sizes to meet your needs!

LADDERS

PLATFORMS

DRYWALL CARTS AND LIFTS




SEALANTS & FLASHINGS

We stock the largest selections of

sealants, flashings, tapes, paints,

and adhesives in the industry!

These high performance products,

for a variety of applications, protect

against the harshest environments.

Need sealants? No problem…Whether you need tube sealants, butyl tapes, foam closures, or pipe flashings, contact our branch to handle the product you need.

Need color matched fasteners or touch-up paint? No problem…SEVEN in-house painting facilities custom color match to any metal panel in three days or less. We can paint fasteners, rivets, and metal components to meet your requirements and supply touch-up paint. Our paint has UV stabilizers that resist chalk and fade.

Need flashing? No problem…From pipe flashings to foam closures, we stock hard to find products that seal out the weather in a variety of applications or conditions.



ost up-to-date product and technical information!• Adhesives - Spray

• Butyl Tape - Metal Panels• Caulking Gun• Closure - Metal Panel / Foam• Closure

VERSA-VENT Roof Venting Closure• Closure - UNIVERSAL CLOSURE• DEK-CAP - Metal Roofing End Cap

Flashing• Drains - Roof• End Cap Flashing - Metal Roof

(Dek-Caps)• Firestop• Flashing -Linear EPDM• Galvanizing Spray• KALIDA-KOTE Touch-up Paint• Lubricant - CROWN / WD40• Paint - KALIDA-KOTE Touch-up Paint• Paint - Marking Spray• Pipe Flashing - PIPEMASTER• PIPEMASTER - Pipe Flashing• PROFILE VENT - Roof Venting Closure• Retrofit Pipe Flashing• Roof Venting - PROFILE VENT

• SealantsNPC SOLAR SEALSCHNEE-MOREHEADButyl, Silicone, Polyurethane, Self-levelingSIKAButyl, Polyurethane, Butyl TapeSONNEBORNPolyurethaneSUREBONDAdhesive, Siliconized RubberTREMCOSilicone, Polyurethane, PourableTFC100/TFC116 Polyurethane,

• Solvent• Tapes

AcrylicAluminumCautionDuctElectricalFacingFoamFoilMaskingPolyesterVinyl

• Underlayment - GRACE• Waterproofing - PEAL & SEAL

SEALANTS & FLASHINGS

FULL LINE OF SEALANTS AND FLASHINGSFULL LINE OF SEALANTS AND FLASHINGS




Step 1Cut on the proper pipe

diameter marked on the flashing

Step 3Apply

polyurethane sealant to the bottom of the

base

Step 2Position over pipe and slide down the pipe

Step 5Fasten with 1/4"

x 1-1/8" self drilling fastener

every 1-1/2" around the base

Five easy steps for assuring a leak free roof penetrationStep 4

Mold the flexible base to the panel

contours

• Flexible, weather resistant EPDM rubber or silicone

• Appropriate pipe size diameter listed on flashing to assure proper fit

• Aluminum base is flexible to conform to any panel profile

• Grey EPDM is ozone and ultraviolet resistant

Pipe Size Flash TFC Number of Outside Diameter Number Part Number Fasteners 1/4" to 2" EPDM #1 001DEKR 10 1-3/4" to 3-1/4" EPDM #2 002DEKR 13 1/4" to 4" EPDM #3 003DEKR 16 *silicone #3 003DEKS 16 3" to 6" EPDM #4 004DEKR 19 4" to 7" EPDM #5 005DEKR 22 *silicone #5 005DEKS 22 5" to 9" EPDM #6 006DEKR 26 6" to 11" EPDM #7 007DEKR 30 8" to 13" EPDM #8 008DEKR 35 *silicone #8 008DEKS 35 10" to 18" *EPDM #9 009DEKR 54 *silicone #9 009DEKS 54

Standard Applications

Note: Numbers 1 and 3 are closed top. When flashing a steep pitch roof greater than 20 degrees, or a profile with a rib height of 1-1/2" or more, use the next larger size flashing for increased flexibility.

EPDM SiliconeAdvanced OzoneResistance 70 hours @ 500pphm 70 hours @ 500 pphmHigh TemperatureResistance Intermittent +135˚ C (275˚ F) +260˚C (+500˚ F) Continuous +100˚C (212˚ F) +225˚ C (+437˚ F)Low TemperatureResistance `-55˚C (65˚F) -74˚C (-100˚F)Tensile Strength (min) 10 MPa (1450 psi) 5 MOPa (700 psi)Compression Set (max) 25% 50%

Material Specifications

Fastening RecommendationCorrosion resistant fasteners should be used around the base one every 1-1/2 inches as per the United Plumbing Code (UPC) recommendations. Refer to size chart for the quantity to use.

Fastener1/4-14 x 1-1/8" DP1 BLAZER Stainless Cap Head with VRT Technology

Sealant RecommendationPolyurethane sealant should be used under the base to assure a proper seal. If you prefer, additional sealant can be applied around base after installation.

PIPE-MASTER PIPE FLASHINGPIPE-MASTER PIPE FLASHINGFOR METAL ROOF SYSTEMSFOR METAL ROOF SYSTEMS




Square Tubing Angle Iron

P: Plastic Snap Rivets • S: Stainless Cable & Aluminum Rivets

Adapters Size 1/2 x 1/2 3/4 x 3/4 1 x 1 2 x 2 3 x 3 4 x 4 Square Part No. D050 D075 D101 D102 D103 D104

Angle Irons SIZE 1-1/2 x 1-3/8 x 1-3/4 x 2-1/2 x 3 x 3x 3x 1 1/2 x 4 x 1-1/2 x 1- 3/8 x 1-3/4 x 2-1/2 x 3 x 3x 3x 1 1/2 x 4 x 1/4 3/16 1/8 1/4 1/4 5/16 3/8 1/4 1/2 Part No. D215 D213 D217 D225 D206 D230 D231 D232 D240

Flash square tubing or angle iron

Available in nine colors to match your roof!Sizes#3 - Pipe diameter 1/4" to 4"#5 - Pipe diameter 4" to 7"

Material: EPDM

Pipe Size TFC Number of Outside Diameter Part Number Fasteners 3/4" to 2-3/4" 801RETDEK 13 2" to 7-1/4" 802RETDEK 23 3-1/4" to 10" 803RETDEK 30

Retrofit Applications

PIPE-MASTER™ RETROUse in retrofit applications EPDM Easy to install

PIPE-MASTER PIPE FLASHINGPIPE-MASTER PIPE FLASHINGFOR METAL ROOF SYSTEMSFOR METAL ROOF SYSTEMS




AZTEC MASTER FLASHAZTEC MASTER FLASH35 YEAR WARRANTY FLASHING35 YEAR WARRANTY FLASHING




AZTEC MASTER FLASHAZTEC MASTER FLASHSOLAR / MULTI-PORT / MINISOLAR / MULTI-PORT / MINI




DEKSTRIPDEKSTRIPEDGE FLASHINGEDGE FLASHING




END CAP FLASHINGEND CAP FLASHINGFOR METAL ROOF SYSTEMSFOR METAL ROOF SYSTEMS




ADHESIVEAdhesive is a bead of glue thatcan be applied to either side of yourclosure configuration. It allows for secured placement of the closure strip prior to installation of the panel.

Specially formulated closed-cell polyethylene foam. The unique fusingprocess results in a plywood-like lamination that of fers exceptional strength anduniform compressibility . many of the closure shapes shown here are availablewith a dovetail interlocking joint that speeds up the installation and eliminatesgapping often found with flat end-to-end joints.

Beveled ClosureWith today’ s emphasis on the architectural aesthetics of metal roofing, unusualcut back angles and valleys result in challenging closure applications. Standard90 degree closure will not provide an acceptable fit and seal. W e can customproduce closure in bevel configurations which take into account the cut backangles and roof slope of each individual application. These parts are custom cutto your panel and specific order needs.

Panel Pitch Hgt. Length Pcs. Ft. Profile Of Of Of Per Per Description Corr . Corr. Strip Ctn. Ctn.2.67" Corrugated 2.67" 1/2" 24" 100 200Wheeling Channel Drain Inner 6" 1/2" 36" 100 300 Outer 6" 1/2" 36" 100 3002.5" Corrugated 2.5" 9/16" 38-3/4" 100 323Granite City Strong Panel II Inner 9" 5/8" 36" 100 300 Outer 9" 5/8" 36" 100 300Metal Sales Pro Panel II Inner 9" 5/8" 36" 100 300 Outer 9" 5/8" 36" 100 3003/4" Hi Rib* Inner 9" 3/4" 36" 100 300 Outer 9" 3/4" 36" 100 300Delta Rib Inner 8" 3/4" 24" 100 200 Outer 8" 3/4" 24" 100 200M/U Panel Inner 6" 3/4" 36" 100 300 Outer 6" 3/4" 36" 100 300A-Panel Inner 12" 1-1/8" 36" 100 300 Outer 12" 1-1/8" 36" 100 300Metal Sales SpanLine 36 RW Inner 12" 1-1/8" 36" 100 300 Outer 12" 1-1/8" 36" 100 300R-Panel Inner 12" 1-1/4" 36" 100 300 Outer 12" 1-1/4" 36" 100 300McElroy Multi-Rib Inner 12" 1-1/4" 36" 100 300 Outer 12" 1-1/4" 36" 100 300* Matches: Grand Rib III, Max Rib, Imperial Rib, Classic Rib and Century Drain

Closure profiles

Chemical Resistance Dimensional Change*Reagent Concentration (% Volume)Sulfuric Acid 30% +0.4

Nitric Acid 10% -0.7

Hydrochloric Acid 10% +5.4

Carbolic Acid 5% +5.0

Acetic Acid 5% -0.6

Oleic Acid -- -0.7

Citric Acid 10% +6.5

Ethyl Alcohol 95% +0.4

Carbon Tetrachloride -- +18.0

Heptane -- 18.5

Ethylene Disulfide -- +3.0

Toluene -- +15.0

Distilled Water -- 0

Hydrogen Peroxide 3% +1.7

Caustic Soda 10% +0.9

Ammonia 10% _5.8

Sodium Carbonate 2% +7.4

Saline 10% +4.0

* Immersion for 7 days at68 ° F.

Performance Units Properties*Bulk Density pcf 2

Average Cell Size mils. 10

Tensile Strength psi M 45-55(ASTM D-1564) C 36-44

Elongation, 20° C % to M 124-152(ASTM D-624) break C 100-122

Tear Resistance, 20° C lb./in. M 10-12(ASTM D-1564) C 7-6

Compression Set, 22 hrs. % of original 16 Max.50% COmpression, 24 hr. thickness recovery (ASTM D-1056)

Service Temperature °F -100 to +180

Thermal Conductivity BTU-in./hr.-Ft.2-°F 0.25

Water Absorption lbs./sq. ft. Max. 0.04(ASTM D-1667 cut surface

Buoyancy lbs./cu. ft. 55.0 Min.

Compression Strength 25% 4.9-6.1 psi 50% 12.7-15.5 75% 38.8-47.4

Shore Hardness AA Scale 7(ASTM D-2240) 00 Scale 51

* M= Machine Direction* C= Cros-Machine Direction* Ozone & UV Test Results Available On Request.

CLOSE-TITE™ CLOSURE CLOSE-TITE™ CLOSURE FOR METAL ROOF SYSTEMSFOR METAL ROOF SYSTEMS




RIDGE VENTING CLOSURERIDGE VENTING CLOSURE




Applications

Universal Closure SealShipped in compressed rolls

AST Sealant Tapes are preformed, resilient, self-adhesive, expanding tape seals made from an open-cell foam that has been impregnated with a water-based, acrylic-modified asphalt emulsion and then compressed to a sealing density' level appropriate to the application. Typically, higher compression levels are required for water-tightness in water run-of f applications; lower compression can be used, for example, for snow seals at roof ridges.

Supplied with adhesive on one side for easy installation

Where to Use AST Hi-AcrylicUse AST Hi-Acrylic in all applications where the material will be allowed to expand to fill voids.

AST Hi-Acrylic is impregnated to higher density and is capable therefore of providing a seal even when not fully compressed.

Used across panel contour at eaves, hips, valleys, peaks, concealed gutters, etc., AST Hi-Acrylic provides a durable and versatile solution to these typically dif ficult-to-seal areas.

Supplied Expanded Box Rolls Roll Product Size Size Quantity Per Box Length code 1/4x 1/2" 1 x 1/2" 984' 50 19.68' EHA2512 (6 x l2mm) (25 x 72mm) (300m) (6m) l/4x 1" 1"x 1" 511.68 LF 26 19.68' EHA2525 (6 x 25mm) (25 x 35mm) (156 m) (6 m) 5/16x3/4" 1 l/4x3/4" 419.84 32 13.12' EHA3O2O (8 x 20mm) (30 x 20mm) (128m) (4m) 1/2x1" 2x1" 314.88' 24 13.12' EHA5025 (12 x 25mm) (50 x 25mm) (96m) (lOm) 3/4x 1" 3x 1" 131.20' 20 6.56' EHA7525 (20 x 25mm) (75 x 25mm) (40m) (2m)

AST Hi-AcrylicStandard & Custom Sizes Available

The following are the most popular sizes but virtually any size material can be provided to suit your specific requirements.

Property Value Test Method Base material Open cell, high density, n/a polyUrethane foam

Impregnation Acrylic-modified asphalt n/a Color Black n/a Tensile strength 21 psi mm (145 kpa) ASTM d357a Elongation-ultimate 150% min ASTM d3574 Temperature range ASTM 711 high - permanent 185°f (85°c) high - short term 203°f (95°c) low -40°f (-40°c) Softening point 140°f min (60°c) ASTM d816 UV resistance Excellent Mildew resistance Excellent Resistance to aging Excellent Bleeding None -400f to 1800f (-400c to 850c) Compression set 3% max ASTM d3574 700c 50% rh after 72 hrs. Thermal conductivity 0.34 btu. In/hr. Fr2.0f ASTM c518 (0.05 wim. 0c) Low temperature flexibility No cracking or splitting ASTM c71 1 320f to -10'f (00c to -230c) Water vapor transmission 0.011 perms ASTM c355-64 at 25% compression

TABLE II Typical Physical Properties of AST

UNIVERSAL CLOSUREUNIVERSAL CLOSURE




Specially formulated for metal roofs or any other application requiring high performance! Description

TFC100™ is a smooth and TFC 1 16™ is a textured, one-component, high-performance, non-sag, multi-propose elastomeric, polyurethane sealant, Meets the requirements of ASTM C-920, Type S, Grade NS, Class 25, Use NT, T, M, G, A, O; TT-S-00230C, Type II, Class A; CAN-19, 13-M87 and California Air Resources Board 2003 requirements for Volatile Organic Compound content.

Where To Use Construction Application Perimeter sealing of windows, doors and skylightsExpansion joints Parapets/flashing Precast/tilt-upFascia Siding Curtain wall internal joints

Structure BuildingsSchoolsParking PlazasStore FrontsStadiums Prisons

Cured 7 days @ 75°F (24°C) and 50% RHMovement Capability, % +- 25 ASTM C-719100% Modulus, psi (Mpa) 125 (0.86) ASTM D-412Hardness, Shore A 30+-5 ASTM C-661Tensile Strenght, psi (MPA) 150+-(1.03) ASTM D-412Elongation at Break, % 500 ASTM D-412Peel Strenght, pli25 ASTM C-794Bond Durablitiy on glass, aluminum and concrete +-25% ASTM C-719

Accelerated Weathering Passes ASTM C-793Staining Passes ASTM C-510

Uncured Skin-Over Time 1.5 hrs. MNATack-Free Time 4 hrs. ASTM C-679Cure Rate 1/8in. / 24hrs. MNAExtrusion Rate, g/min. 325 ASTM C-1183 1/8" orifice @ 90 psi ModifiedSlump of Sealant Nil ASTM D-2202Rheolgical, Vertical 120°F (49°C) Non-sag ASTM C-639Volatile Organic Content 3.64% by wt. 44g/L 0.37 lbs/galService Temperature -40°F to 180°F

Material Properties

POLYURETHANE SEALANTPOLYURETHANE SEALANT




#900 Solar Seal Terpolymer Elastomer/Adhesive Sealant#900 SOLAR SEAL is based on terpolymer technology which of fers an alternative to silicone & urethane sealants.

High performance terpolymer elastomers impart exceptional weather resistance, adhesion, elongation and color fade resistance to #900 SOLAR SEAL.

• Approximate coverage 14 Lin. ft./tube• PRIMERLESS• PAINTABLE

Joint Design

• Maximum joint & sealant width is 3/4"• Maximum sealant depth is 1/2"• Minimum application depth is 3/8"

Construction StandardsMeets performance requirements of TT-S-00230c, Class A, Type II and ASTM C-920, Type S, Grade NS, Class 25, Use NT, except for weight loss.

Colors• Clear, White, Black and over 200 NPC standard colors.• Mfg. Name & Color stamped on each plunger .• Custom colors available in low minimum quantities.

General Information• Shelf life: I Year @ 75°F• Substrate temperature : 11°/125°F• Service temperature : -4°/300°F• Cure rate: ~ 75°F a) Thin skin in 24 hrs. b)Complete: 21 days @ 75°F

Expected life: 20+ years when bead is installed as directed for approved applications.

Bond cohesion TT-S-230c No Bond Loss Shore a hardness TT-S-230c 30 Average Stain index TT-S-230c None SAG TT-S-230c No SAG UV & cold exposure ASTM C 920 No Cracking Elongation ASTM-D 412 300% - 400% Tack free time ASTM-C-679 4 hours Adhesion-in-peel TT-S- 1543 30 lbs/in

Performance Data

SEALANTSSEALANTSTERPOLYMER / POLYURETHANETERPOLYMER / POLYURETHANE

Sonolastic® NP 1™One-ComponentElastomeric Gun-Grade Polyurethane Sealant

Where to Use NP 1™• Concrete• Masonry• Aluminum• Wood• Expansion Wall Joints• Curtain Wall Construction• Panel Walls• Precast Units• Aluminum and Wood Window Frames• Fascia• Parapets• Structural Components• Vinyl Siding• Interior and Exterior

Property ResultService temperature range, °F (°C) -40 to 180 (-40 to 82)

Expected Life Up to 20 Years

Shrinkage None

Order InformationPacking:• 300 mL Cartridges, 30 Cartridges to a Carton.• 20 U.S. fl. oz. (590 mL) ProPak Sausage Cartridges, 20 ProPaks to a Carton.• 4.5 gallons (17.0 L) in 5 gallon pails (18.93 L) available in special orders only.

Shelf life is 1 year for cartridges and ProPaks, and 4 months for pails when stored in unopened containers under normal conditions. Storing at elevated temperatures will reduce shelf life.

ColorsA complete line of standard color is available, including White, Off-White, Limestone, Stone, Tan, Aluminum Gray, MediumBronze, Special Bronze, Redwood Tan, and Black.

Typical Properties

Coverage Linear Ft. per Gallon* Joint Joint Width (Inches) Depth (In.) 1/4 3/8 1/2 5/8 3/4 7/8 1 1/4 308 205 154 122 --- --- ---

3/8 --- --- --- 82 68 58 51

1/2 --- --- --- --- 51 44 38

• One gallon equals approximately 12 cartridges or 6 ProPaks.




SM5430 AcryI-R® Non-Skinning, Non-Sag SSR (Standing Seam Roof) SealantA high performance, high solids, non-skinning, non-drying standing seam root (SSR) sealant based on a unique elastomer that provides a non-stringy consistency and excellent resistance to severe environmental conditions of heat, cold, and moisture. Specifically formulated for precise application into concealed panel joints for roll forming lines (standing seam roof panels). It has excellent cut-off characteristics and is not stringy or messy to apply. It is also designed for sealing the warm side of concealed exterior polyurethane foam panels to form a vapor barrier seal. It is formulated without asbestos fillers.

• Excellent adhesion to oily GALVALUME, ZINCALUME, KYNAR 500, aluminum, aluminized steel, polyvinyl fluoride and siliconized polyester painted metal, concrete, FRP and glass

• Factory-caulked panels can be erected in the field up to six months after factory caulked

• No cracking or loss of adhesion at -60 °F

• Service Temperature Range -60°F to 200°F Application Temperature Range 10°F to 120°F

• Will resist fungal attack and not support mildew growth

• Excellent for sealing between dissimilar metals to prevent electrolysis

• Meets Federal Specification TT-C-1 796A, Type I, Class A

PERMATHANE® SM7100 & SM7108 One Part Polyurethane Sealants5M7160 is an all-purpose polyurethane sealant. 5M7108 is a firmer tooling, construction grade polyurethane sealant. Both products are one-component, high performance polyurethane sealants with excellent adhesion and elongation. Designed for sealing exterior panel joints, gutters, roof curbs, roof jacks, skylights, air conditioning equipment, curtain wall joints and perimeter sealing windows and doors. They are ideal for dynamically moving joints with exceptional resistance to cuts and tears.

• Excellent adhesion to oily GALVALUME, ZINCALUME, KYNAR 500, aluminum, aluminized steel, polyvinyl fluoride and siliconized polyester painted metal, concrete, FRP glass, concrete, and block"brick

• Can be applied to damp surfaces and withstands prolonged water immersion

• Service Temperature Range -40°F to 200°F

• Elongation (ASTM D412) 500 to 600%

• Tensile Strength (ASTM D412) 300 psi

• Designed to accommodate 50% total joint movement

• Excellent weatherability and UV resistance

SM5731 Poly-Glaze® PLUS Silicone-Neutral CureA one-component, neutral cure, medium modulus, non-corrosive silicone sealant with excellent adhesion to pvc, aluminum, glass and a variety of painted surfaces without priming. GAL VALUME and ZINCALUME coated metals require an amine free and acetic acid free silicone sealant for long-term performance.

• Remains permanently elastic• Excellent adhesion to clean GALVALUME, ZINCALUME, PVC, KYNAR 500 and painted metal surfaces• Tack-Free Time 10 minutes 1/4" bead ©77 °F 50% R.H.• Cure time 10 hours 1/4" bead ©77 °F, 50% R.H.• Service Temperature Range -60°F to 400°F• USDA acceptable• Colors: Clear and White• Not paintable• Excellent weatherability when exposed to ultraviolet, radiation, rain and atmospheric hydrocarbons and extremes in temperature

SCHNEE-MOREHEAD SEALANTSCHNEE-MOREHEAD SEALANT




SB-200 Panel And Foam AdhesiveA multi-purpose, quick grabbing,- waterproof adhesive used for paneling, plywood, hardboard, pre-finished panels to new and existing walls. Bonds well to foam insulation panels, and is used to install foam to concrete.. wood and drywall, etc. Conforms to FHA 906.4.3. Packed 24 -1/16ths or 12 qts. per case.

SB-400 Decking Construction AdhesiveQuality waterproof, high strength, rubber base decking adhesive for gluing subfloors. It produces a stronger floor and absorbs vibration and bridges that eliminate nail pops and backouts to stop squeaks and deflection. Also used to bond furring strips to concrete walls. Conforms to or surpasses specifications FHA UM-60, PFS, APA-AFO-01, UN-STD-1740 C557-73. Packed 12 qts. per case.

SB-190 Everseal Heavy Duty Sealant-AdhesiveA Durable and tough Super Strength, yet flexible sealant for good life and movement Economical multi-purpose application to all types of building materials including the tougher to seal materials: fiberglass, vinyl and plastic It is paintable, pick -proof for public buildings. Packed 24 -1/16ths or 12 qts. per case.

SikaLastomer 501 Non Skinning Butyl CaulkOff White Butyl for Standing Seam RoofsSikaLastomer 501 is a premium grade, high solids, non-skinning, non-drying butyl rubber-based compound designed for caulking the female lip of standing seams roof and wall panels. It is intended for use in concealed indoor and outdoor applications.

This caulk has permanent tack which allows the caulk to be bonded in the field between two metal surfaces up to six (6) months after initial application.

It also has excellent adhesion to metals lightly coated with mill lubricants, oily GAL VALUME, galvanized metal, KYNAR 500, ZINCGRIP, and aluminized steel.

Sikaflex® 201One Part Polyurethane SealantSikaflex One Part Urethane Sealant ia a high performance, medium modulus, single component moisture curing construction grade joint sealant. It exhibits good adhesion to oily GALVALUME, ZINCGRIP, and aluminized steel, without attacking the metal coating. It also bonds to fiber reinforced polyester (FRP), polyurethane, polyvinyl fluoride, and siliconized polyester painted metal.

This unique weather resistant sealant has high recovery making it ideal for sealing dynamically moving joints. It has exceptional resistance to cuts and tears. It is faster curing than silicone and solvent acrylic sealants.

SEALANT AND ADHESIVESSEALANT AND ADHESIVES




SPECTREM® 2 High Performance Silicone SealantSpectrem 2 is a medium moduLus, one part, high performance, neutral cure silicone seaLant ideal for a variety of caulking and glazing applications.

Limitations:• Do not apply to damp or contaminated surfaces.• Use with adequate ventilation

Standard Colors:White, Off White, Graystone, Gray, Bronze, Limestone and Black

Application:Spectrem 2 is easy to appLy with conventional caulking equipment. Bill joint completely and tool. At 75°F (23.°C), 5O% R.H. a durable skin wiLL form typically within less than 10 minutes.

TREMSIL® 200General Construction Grade Silicone SealantTremsil 200 is a one-part, acetoxy silicone sealant. Tremsil 200 cures to a flexible rubber when exposed to moisture present in the air.

Limitations:• Do not apply over damp or contaminated surfaces.• Use with adequate ventilation.

Packaging:1/12 gallon (300 ml) cartridges.

Standard Colors:Anodized Aluminum, Black, Clear, Dark Bronze, Gray, Ivory, and White.

Application:Tremsil 200 is easy to apply with conventional caulking equipment. Fill joint completely and tool. At 75°F (23.9°C), 500/0 R.H. a durable skin wilt form within 30 minutes.

DYMONIC®Low Modulus Joint SealantDymonic is a high performance, low modulus, one-component, moisture curing, modified polyurethane joint sealant.

Basic Uses:Dymonic is specifically developed for sealing dynamically moving joints such as: expansion and con-trol joints, precast concrete panel joints, tilt-up panel joints, curtain wall joints and perimeter caulking (window , doors, panels, radon miti-gation, bedding of mullions and frames, etc).


Standard Colors:White, Precast White, Off White, Limestone, Graystone, Aluminum Stone, Anodized Aluminum, Ivory, Beige, Buff, Redwood Tan, Light Bronze, Bronze, Black, Hartford Green, and Forest Green.

Application:Dymonic is easy to apply with con-ventional caulking equipment. Fill joint completely with a proper width-to-depth ratio.

Packaging:1/12 gallon (300 ml) cartridges, 20 oz. (600 ml) sausages, 2 gallon (7.57 L) and 4.5 (17.1 L) gallon pails and 55 gallon (208 L) drums.

Packaging:1/12 gallon (300 ml) cartridges, 20 oz. (600 ml) sausages, 2 gallon (7.57 L) and 5 (19 L) gallon pails and 55 gallon (208 L) drums.

TREMCO SEALANTTREMCO SEALANT




Packaging:Quart (850 ml) cartridges, packaged 16 per case. Also available in 5 gallon (19 L) pails and 55 gallon (208 L) drums.

Packaging:1/12 gallon (300 ml) cartridges, 20 oz. (600 ml) sausages, 2 gallon (7.57 L) and 5 (19 L) gallon pails and 55 gallon (208 L) drums.

VULKEM SEALANTVULKEM SEALANT

VULKEM® 145One-Part Pourable Polyurethane SealantVulkem 45 is a one-part moisture curing, pour grade polyurethane joint sealant. V ulkem 45 does not require a primer on most construction materials.

Basic Uses:Vulkem 45 has been formulated for sealing expansion and control joints in parking garages, plazas, terraces, highways, bridges, swimming pool decks, reservoirs, sewage treatment plants, floor and sidewalk joints.

Extraordinary adhesion, cohesion, abrasion and tear resistance are inherent in the base polymer . Vulkem 45 is suitable for use in continuous water immersion.


Standard Colors:White, Limestone, Gray, Buff/Dark Tan, and Black.

Application:Vulkem 45 is easy to apply with conventional caulking equipment. At 75'F (23.9'C), 500/0 R.H. a skin forms within 24 hours. Curing continues at the rate of 1/16 inch (0.16 mm) depth per day . The cure rate is reduced at lower temperatures and less humidity.

VULKEM® 116Weatherproofing Sealant One-Part High Performance ElastomerVulkem 116 is a one-part moisture curing, gun grade polyurethane sealant. V ulkem 116 is durable, flexible and offers excellent performance in moving joints. Vulkem 116 does not require a primer on most construction materials.

Basic Uses:Vulkem 116 is an excellent general purpose sealant designed for use in precast, masonry , window frame perimeters and similar types of construction joints. V ulkem 116 is suit-able for continual immersion in water . Vulkem 116 is designed for exterior and interior use.


Colors:Aluminum, Black, Dark Bronze, Bronze, Buf f, Gray, Ivory, Limestone, Redwood Tan and White.

Application:Vulkem 116 is easy to apply with conventional caulking equipment. Fill joint completely and tool. At 75'F (23.9'C), 50010 R.H. a durable skin forms within 24 hours. Curing continues at the rate of 1/16 inch (1.6mm) depth per day. The cure rate is reduced at lower temperatures and less humidity .




• Expels over 135 (10 oz.) tubes of latex per battery charge

• 620 pounds of pushing force easily handles high viscosity materials such as windshield urethanes

12 Volt Caulk Gun with 10 Ounce Carriage Kit6560-21

• Expels over 50 (quart size) tubes of sub-floor adhesive

• 620 pounds of pushing force easily handles high viscosity urethanes and adhesives

12 Volt Caulk Gun with Quart Carriage Kit6560-23

• Expels up to 30 packs of standard caulk on a single charge

• 620 pounds of pushing force easily handles high viscosity urethanes and adhesives

12 Volt Caulk Gun with 20 Ounce Sausage Carriage Kit6560-24

COX Model 21001 (Wexford II)• Non-drip feature• Standard 10.3 oz. cartridge• Mechanical advantage 7:1• Body-Injection mold, fiberglass, nylon• Hex Drive Rod

COX Model 41004 (Chilton)• WCD- approx. doubles gun life• Standard 10.3 oz. cartridge• Mechanical advantage 12:1• Body- Die cast zinc alloy

CAULKING GUNSCAULKING GUNS

We stock a wide selection of caulking guns. Call TFC for your specifi c need!




Product DescriptionVycor Ice & Water Shield membrane is composed of two water proofing materials--an aggressive rubberized asphalt adhesive, backed by a layer of high density cross laminated polyethylene. The rubberized asphalt surface is backed with a release paper that protects it’s adhesive quality. During application, therelease paper is removed, allowing the rubberized asphalt to bond tightly to the roof deck.

Vycor® Select

Self-Adhered RoofingUnderlayment For General Roof LeakProtection

Vycor® Ultra

Self-Adhered RoofingUnderlayment For High TemperatureApplications

Roll Roll Roll Shipping Rolls PerLength W idth Size Packaging Weight Pallet75 ft (22.9 m) 36 In (914 mm) 225 ft2 (20.9 m2) Corrugated Cartons 70 lbs (31.7 kg) 3536 ft (11.0 m) 36 In (914 mm) 108 ft2 (10.4 m2) Corrugated Cartons 38 lbs (17.2 kg) 35

Product Data

Roll Roll Roll Shipping Rolls PerLength W idth Size Packaging Weight Pallet65 ft (19.8 m) 36 In (914 mm) 195 ft2 (18.1 m2) Corrugated Cartons 34 lbs (15.4 kg) 25

Product Data

Roll Roll Roll Shipping Rolls PerLength W idth Size Packaging Weight Pallet70 ft (21.3 m) 34 In (864 mm) 198 ft2 (18.4 m2) Corrugated Cartons 43 lbs (19.5 kg) 25

Product Data

Property V alue Test MethodColor Gray-Black ---Thickness, Membrane 40 mil (1.02 mm) ASTM D 3767 Method ATensile Strength, Membrane 250 psi (1720 kN/m2) ASTM D 412 (Die C Modified)Elongation, Membrane 250% ASTM D 412 (Die C Modified)Low Temperature Flexibility Unaffected@ -25° F (-32° C) ASTM D 1970Adhesion to plywood 3.0 lb/in. width (525 N/m) ASTM D 903Permanence (Max) 0.05 Perms (2.9 ng/m2s Pa) ASTM E 96Material Weight Installed (Max) 0.3 lb/ft2 (1.3 kg/m2) ASTM D 461

Performance Properties

Product DescriptionVycor Select is composed of two waterproofing materials--a rubberized asphalt adhesive, backed by a layer of high density cross laminated polyethylene. The product is 25 mil (0.64 mm) thick, making it lightweight and easy to handle and apply. The unique, advanced rubberized asphalt formulation allows the membrane to meet industry standards for fastener sealability equivalent to products that are often significantly thicker and heavier .

The rubberized asphalt is backed by a release liner that protects it’ s adhesivequality. The release liner is easily removed, allowing the rubberized asphalt to be bonded to the roof deck.

Product DescriptionVycor Ultra is composed of two waterproofing materials--an aggressive butyl rubber based adhesive, backed by a layer of high density cross laminated polyethylene. The product is 30 mil (0.76 mm) thick, making it easy to handle and apply. The unique, advanced adhesive formulation of fers premium adhesion to the roof deck, high quality laps, superior seal around roofing fasteners, and outstanding hightemperature stability.

The adhesive is backed by a protective plastic release liner that protects itsadhesive quality. The release liner is easily removed, allowing the adhesive to be bonded tightly to the roof deck.

Vycor® Ice & Water Shield®

Self-Adhered RoofingUnderlayment ForPremium Roof LeakProtection

UNDERLAYMENTUNDERLAYMENT




BUTYL TAPE-SEAL™ was designed specifi cally for the metal building industry to provide optimal sealing in the harshest environments.

It adheres to most clean, dry metal surfaces and does not harden, bleed or stain. With pressure, it fi lls minor irregularities in the surface and seals the joints providing an effective barrier against water, moisture, dust, and dirt.

BUTYL TAPE-SEAL™ is an excellent choice for use around windows, doors, roof vents, stacks, access doors, and other penetration points.

Adheres to:• Painted Metal• Galvalume®• Kynar®• Aluminized Metal

Easy to install!

Specially formulated for use on metal roof and wall panels.

TAPE-SEAL

Mineral spirits will readily facilitate the cleaning of tools and equipment.

PACKAGING

BUTYL TAPE-SEAL™ is extruded butyl material with a silicone backed release paper that is rolled and cut to specifi c lengths.

Our master cartons are constructed of 200 pound test material and the rolls are separated by silicone divider pads and protected by uprightstacking cores.

CLEAN UP

SIZES

Size(T x W x L) TFC P.N.

Rolls/Ctns

Ctns/Pallet

3/32” x 3/8” x 45’ 0937BCT 48 303/32” x 1/2” x 50’ 0950BCT 22 503/32” x 1” x 45’ 0910BCT 24 301/8” x 1/2” x 50’ 1250BCT50 13 481/8” x 1” x 50’ 1210BCT50 8 48

3/16” x 1/4” x 40’ 1825BCT 20 483/16” x 7/8” x 40’ *DB 1887BCT 10 48

3/16” x 7/8” x 25’ 1887BCT25 8 643/16” x 2-1/2” x 20 *TB TC826W 6 60

Stocked sizes - Others available upon request

*DB denotes double bead*TB denotes triple bead

TFC BUTYL TAPE-SEAL FOR METAL TFC BUTYL TAPE-SEAL FOR METAL ROOFING AND WALL PANELSROOFING AND WALL PANELS




BUTYL TAPE-SEAL™ is made from a blend of elastomers, butyl, EPDM rubber, and proprietary co-polymers.

The plasticizers are of the polyisobutylene and polybutene type, and permit no oxidation or migration. The fillers are inert and are primarily used as extenders and process aids and, to a lesser extent, as reinforcing pigments. The remaining materials are antioxidents, fungicides and organic processing aides.

Property ResultsColor ASTM D1729-69, Off white to grey

Solids Content ASTM C771-74, 100%Specifi c Gravity ASTM D71-78, 1.53+/-.05

Hardness ASTM D217-68 (300 gr. total weight)0oF (-18oC) - 3.5 to 4.5 mm min.77oF (25oC) - 10.0 to 13.0 mm 120oF (49oC) - 12.0 to 18.5mm max.

Force to Compress As measured when one cubic inch of 3/8” thick material iscompressed to 3/16” thick material @ 2”/min.0oF (-18oC) - 85 lbs.77oF (25oC) - 40 lbs.120oF (49oC) - 29 lbs.

Elongation & Webbing 0oF (-18oC) 250% min. (holding a 5 in. water head pressure Ethylene glycol added)77oF (25oC) - 800% min.

Plasticizer Migration ASTM C772-74, No bleed / contact stain onlyStaining ASTM D925-76, No bleed / contact stain only

Cold Temperature Flexibility ASTM C765-73, No cracking or loss of adhesionWater Resistance ASTM D1056, Vacuum - .75% max. Static - 0%

Adhesion Tensile Strength ASTM D897-78, 20 psi min.Aging Characteristics ASTM D7850-68

Weather-O-Meter, 1000 hrs - 10% reduction in most physicalsQUV Cabinet (No ASTM) - 10% reduction in most physicals

Shelf & Service Life 20 years min.Service Temperature -400F to 220oF

Heat Distortion ASTM D816-55 / 25% max.Water Resistance ASTM D1056 / Vacuum: .75% max. Static: 0%

Static Water Head Test MBNA waster damming test, Passed 5in waterhead simulation.

MATERIAL SPECIFICATION

TEST DATABUTYL TAPE-SEAL™ has been tested to ASTM standards and meets Military and Federal Specifi cations.

Military SpecificationsMIL-C-18969B, Type II, Class BFederal SpecificationsTT-C-1796A, Type II, Class B(Supercedes MIL-C-18909B)U.S.D.A. - Product chemically acceptable to the U.S. Department of Agriculture for use in meat processing areas under Federal inspection.

TAPE-SEALSSSTTTTTTTTTTAAAAAAAAAAPPPPPPPPPPEEEEEEEEEE----------SSSSSSSSSSSEEEEEEEEEEAAAAAAAAAALLLLLLLLLL

TFC BUTYL TAPE-SEAL FOR METAL TFC BUTYL TAPE-SEAL FOR METAL ROOFING AND WALL PANELSROOFING AND WALL PANELS




THE BETTER WAY TO FINISH LOW SLOPE ROOFSand make quick waterproof repairs

• Aluminum Surface• Also Available with Gray or

White Factory Coated Surface• No Torches or Mops• No Adhesives• No Expensive Tools• No Coating

Packaged 100 square feet per carton.

Available widths: 4", 6", 9", 12", 18", 36"

As an ENERGY STAR ® Roof Products Partner, MFM Building Products has determined that aluminum surface PEEL & SEAL meets the ENERGY STAR ® guidelines for energy efficiency.

®

10 - Y E A R W A R R A N T Y

Peel off the release paper, press the material into place. It’ s that simple!

The perfect solution for low slope and dozens of other roofing problems, PEEL & SEAL installs using only a utility knife. You can forget big crews, hot kettles, torches, adhesives and fasteners. No coating is necessary . PEEL & SEAL adheres to most surfaces and saves time, labor and money. It won’t crack or dry out.

PEEL & SEAL replaces old-style rolled roofing products. It’ s rugged, lightweight and reflects heat ... and it seals around most punctures. It’ s quick and economical to install and is a perfect answer to roofing, waterproofing, patching and repair ... any job requiring tough, weatherproof protection.

Patch leaking roofs quickly & ef fectively with PEEL & SEAL.

PEEL & SEAL helps solve metal roof problems – corrugated or standing seam – on industrial, commercial and farm buildings.

SEE COMPLETE INSTRUCTIONS IN BOX BEFORE APPLICATION

GeneralPEEL & SEAL is a multi-purpose waterproofing material. Apply PEEL & SEAL in fair weather at temperatures above 60° F. A minimum slope of 1/2" per foot is required. Not designed for ponding areas. NO TOP COATING IS REQUIRED. Storage: Keep rolls dry, protect from sunlight.

Surface PreparationPEEL & SEAL may be applied directly to roof decks including wood, metal, masonry and existing smooth asphalt roofs. Because of the unpredictable condition of existing roofs, MFM cannot guarantee the performance of PEEL & SEAL over mineral surfaces. The surface to receive PEEL & SEAL must be clean, dry and free from oil, grease or debris – prime where necessary.

PEEL AND SEALPEEL AND SEAL




SEALING TAPESEALING TAPE




FIRE STOPFIRE STOP

For product information, please contact TFC with your specific application and we will provide you with additional details.




2oz BottleWith Brush

• Polyurethane enamel can be matched to any color!• Baked on finish provides a tough, chip resistant finish.• UV protection.• In stock colors for immediate shipment from 7 locations!• Customized painting of metal closure and gutter straps.• Special colors in 3 days or less!!!

SpecificationsFinish: Gloss Enamel 85 units minimum at 60 degrees Exterior Catalyst

Thickness: 1.6 - 2.0 mils

Adhesion: ASTM D 3359 - Excellent No peeling or removal

Impact Resistance: ASTM D 2794 Good: > 10 in.lbs.

Abrasion Resistance: ASTM D 4060 Good

Corrosion Resistance: Salt Spray - 1,000 hrs(< 5% red rust) Kesternich - 30 cycles

Paint pen

KALIDA-KOTE™High Performance Paint for Fasteners, Rivets, and Metal Closures

Touch-Up Paint Custom Color Matched To Your Panel or TrimTriangle Fastener offers Kalida-Kote painting process, producing perfect color matched fasteners, rivets, and metal closure. W e start by using a special formula polyurethane enamel with UV protection that is expertly color matched.

After spraying, we cure the finish by baking to produce a tough chip resistant finish assuring long-life. Kalida-Kote is compatible with Kynar paint finishes.

We supply touch-up paint that is color matched to your specific requirement!

1/2 Pint Can With Brush

PAINT FOR FASTENERS, PAINT FOR FASTENERS, RIVETS & CLOSURESRIVETS & CLOSURES




Job Liner PaintsAn upside down marking paint for striping. To be used withour Crown Job Liner Marking Machine.

Available Colors:Traffic Yellow, Traffic White, Black, Dark Handicap Blue

Upside Down Paints - AerosolInverted spray for marking and painting. Solvent based but contains justenough water so the grass will not be harmed and it also brightens the colors.

For your comfort, best used with Crown Guideliner Marking Machine

Available Colors:Red Fluorescent, Blue Fluorescent, Green Fluorescent, Yellow,Orange Fluorescent, White, Kleer, Hot Pink Fluorescent

Cold Galvanizing Compound• The best long-term rust protection you can buy .• 93% zinc-rich coating bonds to iron and steel.• Aerosol will not clog or sputter.

DescriptionProvides corrosion protection to ferrous metal surfaces first, as a long-lived coating of practically pure Zinc comparable to that obtained by galvanization and second, through sacrificial anodization. This protection becomes effective when the surface is scratched, broken or corrupted. With the presence of moisture the Zinc coating will corrode while continuing to protect the metal it covers.

Crown Guideliner Marking Machine• Ready for use with Crown Upside Down Paints• Ready to use, no accessories required• Easy on your back

Job Liner Marking Machine• For use with Crown Job Liner Paints• Ready to use, no accessories required• Versatile• Simple adjustments for strip widths of 2 - 4"• Applies sharp, even lines every time

COLD GALVANIZING COLD GALVANIZING MARKING PAINTMARKING PAINT

MARKING PAINT




274274

High Tack 1.5 mil (38 micron) Aluminum Foil TapeA special 1.5 mil (38 μ) high strength aluminum foil tape with a higher tack, special C.W. cold weather acrylic adhesive system. This formulation combines extremely high quick stick at normal temperatures with superior performance at low temperatures and high humidity.

Primary use: Thinner material allows for superior conformability in vapor sealing of fiberglass ductboard and FSK systems.

Thickness: 3.0 mils (75 μ) (exclusive of liner)Adhesion: 98 oz./inch width (27.7 N/2.5 cm)Elongation: 4.4%Tensile: 21 lbs./inch width (95 N/2.5 cm)Widths: 2, 21/2, 3, 4 inches (5.1, 6.4, 7.6, 10.2 cm)Lengths: 50, 100 yards (46, 91 m) on 3 inch (7.6 cm) coreU.S. Coast Guard Approval No: 164.012/120/0for interior finish.Conforms to British Standard BS 476:Part 7, Class 1; Part 6, Class 0.

UL-181A Printed 2 mil (50 micron)Aluminum Foil Ductboard TapeHeavy duty, high strength aluminum foil with specially formulated acrylic adhesive system. Performance and materials guaranteed to meet or exceed UL-181A-P and UL-181B-FX quality standards, and assures against this tape being a conductor of any flame. Superior adhesion and conformance for fibrous ductboard systems.

Primary use: Superior vapor sealing of fiberglass ductboard.

Thickness: 4.0 mils (100 μ) (exclusive of liner)Adhesion: 66 oz./inch width (18.8 N/2.5 cm)Shear Adhesion: 5 lb. weight–24 hours+ 40°F/6 hours 10 lb. weight–>120 hours+ 73.4°F/120 hours 1 lb. weight–>6 hours+ 150°F/6 hoursElongation: 4.3%Tensile: 25 lbs./inch width (113.2 N/2.5 cm)Widths: 21/2, 3 inches (6.4, 7.6 cm)Length: 60 yards (55 m) on 3 inch (7.6 cm) core

2 mil (50 micron) Aluminum Foil TapeA 2 mil (50 μ) high strength aluminum foil coated with special cold weather acrylic adhesive system that combines superior quick stick at normal temperatures with superior low temperature performance at freezing (32°F or 0°C). The ultimate in cold weather tapes. Recommended for use at normal and high temperatures also.

Primary use: Improved vapor sealing of fiberglass ductboard, ductwrap and FSK systems.

Thickness: 3.5 mils (88 μ) (exclusive of liner)Adhesion: 96 oz./inch width (27.1 N/2.5 cm)Elongation: 4.4%Tensile: 27 lbs./inch width (122 N/2.5 cm)Widths: 2, 21/2, 3, 4 inches (5.1, 6.4, 7.6, 10.2 cm)Lengths: 50, 100 yards (46, 91 m) on 3 inch (7.6 cm) coreU.S. Coast Guard Approval No: 164.012/120/0for interior finish.

Conforms to British Standard BS 476:Part 7, Class 1; Part 6, Class 0.

1521CW

1520CWNT

1581A

VENTURE TAPEVENTURE TAPEALUMINUM FOILALUMINUM FOIL




WMP®-10 Polypropylene Facing TapeWhite metallized polypropylene/scrim/kraft laminated facing tape. 4 x 4/sq.in. (2.5 x 2.5 cm) Tridirectional scrim reinforcement. C.W. acrylic adhesive.Colors: Black, White

Primary use: Closure system and vapor seal on Lamtec WMP®-10 faced thermal insulation.

Thickness: 7.0 mils (175 μ) (exclusive of liner)Adhesion: 68 oz./inch width (19.2 N/2.5 cm)Tensile: 40 lbs./inch width (181 N/2.5 cm)Widths: 3, 5 inches (7.6, 12.7 cm)Lengths: 50, 100 yards (46, 91 m) on 3 inch (7.6 cm) core

WMP®-VR Polypropylene Facing TapeTridirectionally reinforced U.L. listed white polypropylene/scrim/kraft lamination. Coated with Venture’s C.W. cold weather acrylic adhesive system for superior quick stick at temperatures as low as 10°F (–12°C). Better in humid as well as hot conditions.Colors: Black, White

Primary use: Closure system and vapor seal on Lamtec WMP®-VR and WMP-50 faced thermal insulation.

Thickness: 7.5 mils (187 μ) (exclusive of liner)Adhesion: 68 oz./inch width (19.2 N/2.5 cm)Tensile: 40 lbs./inch width (181 N/2.5 cm)Widths: 3, 5 inches (7.6, 12.7 cm)Lengths: 50, 100 yards (46, 91 m) on 3 inch (7.6 cm) core

Vinyl Foam Sealant TapeSpecially formulated, closed cell vinyl foam tapes with 10 lb. per cubic foot density. Gray in color. Very flexible, with a specially formulated acrylic adhesive system.

Primary use: Vapor seal where large spaces occur, and asa lap joint seal in corrugated metal building panels or prefabricated wall panels. Thermal break tape.

Thickness (exclusive of liner) Length 1716: 1/16 inch (1.6 mm) 100 feet (30.5 m) 1718: 1/8 inch (3.2 mm) 75 feet (22.8 m) 1714: 1/4 inch (6.3 mm) 50 feet (15.2 m)

Adhesion: 20 oz./inch width (5.5 N/2.5 cm)Widths: 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, 1, 11/4, 11/2, 2 inches (.63, .95, 1.3, 1.6, 1.9, 2.2, 2.5, 3.2, 3.8, 5.1 cm)

FSK Facing TapeTri-directionally reinforced with 2 x 3/sq.in. (2.5 x 2.5 cm) fiberglass scrim, U.L. listed Foil/Scrim/Kraft lamination. Coated with a special cold weather acrylic adhesive system which combines very high quick stick at normal temperatures with superior low temperature performance. Recommended for use down to 10°F (–12°C) as well as normal and very high temperatures. Conforms well to both fibrous ductboard and blankets. The ultimate in cold weather tapes. Meets ASTM C1136. Also available shrink wrapped and labeled.

Primary use: Vapor seal on FSK faced fiberglass ductboard and blanket systems.

Thickness: 6.5 mils (165 μ) (exclusive of liner)Adhesion: 92 oz./inch width (26.0 N/2.5 cm)Elongation: 2%Tensile: 40 lbs./inch width (178 N/2.5 cm)Widths: 2, 3, 4, 5 inches (5.1, 7.6, 10.2, 12.7 cm)Length: 50, 100 yards (46, 91 m) on 3 inch (7.6 cm) core

Conforms to British Standard Class 1BS 476: Part 7.

1525CWNT

1531CW

1537CW

1700 Series

VENTURE TAPEVENTURE TAPEFACING AND SEALINGFACING AND SEALING




276276

SST 4 mil (100 micron) Acrylic Transfer TapeUnsupported clear acrylic, pressure sensitive transfer adhesive utilizing Venture’s special, cold weather acrylic adhesive system on a specially treated, silicone coated easy-release liner. Superior quick stick at normal tem peratures, superior performance below freezing down to 10°F (–12°C).

Primary use: Self-sealing tab for joining the laps of metal building insulation. Cuts installation time, eliminates stapling, pinning, gives a complete vapor seal. Excellent under adverse conditions.

Thickness: 4 mils (100 μ)Adhesion: 120 oz./inch width (34.0 N/2.5 cm)Widths: 1, 11/2, 2 inches (2.5, 3.8, 5.1 cm)Lengths: 60, 180, 336 yards (55, 165, 307 m) on

3 inch (7.6 cm) core

Double Coated Polyester TapeA self-sealing lap tape for use in temperature extremes. Coated on both faces with Venture’s C.W. cold weather acrylic adhesive formulation combining superior quick stick with excellent adhesion performance down to–17°F (–27°C).

Primary use: High performance insulation mounting in high and low temperature extremes.

Thickness: 3.75 mils (93 μ)Adhesion: 83 oz./inch width (23.5 N/2.5 cm)Elongation: 100%Tensile: 7.5 lbs./inch width (33.9 N/2.5 cm)Widths: 1, 11/2, 2 inches (2.5, 3.8, 5.1 cm)Lengths: 60, 180, 360 yards (55, 165, 329 m) on

3 inch (7.6 cm) core

Embossed Vinyl TapeThin, strong, conformable, premium vinyl tape. Particularly aggressive acrylic adhesive system bonded securely to its backing. Shrink and plasticizer resistant.

Primary use: Seaming vinyl faced fiberglass insulation in metal buildings and for water heater blanket installation.Colors: White, Gray, Black

Thickness: 5 mils (125 μ) (exclusive of liner)Adhesion: Peel—57 oz./inch width (15.9 N/2.5 cm)

Hold—Minimum 4 hours @ 2 psi load

Tensile: 1980 psi (8996.9 N/2.5 cm), machine direction;1800 psi (8514.0 N/2.5 cm), transverse

Widths: White—3, 5 inches (7.6, 12.7 cm)Black—3 inches (7.6 cm)Gray—3 inches (7.6 cm)

Length: 50 yards (46 m) on 3 inch (7.6 cm) core

460 Series

594CW

514CW

VENTURE TAPEVENTURE TAPEVINYL AND TRANSFERVINYL AND TRANSFER

Double Face Foam TapeDouble coated polyolefin foam with acrylic adhesive on both sides. Used for permanent bonding to metal, glass and other smooth surfaces where watertight and airtight bond is required. 1/16 in. thick for heavy duty applications.

Width x Thickness x Length1/4" x 1/16" x 36 yds.1/2" x 1/16" x 36 yds.3/4" x 1/16" x 36 yds.1" x 1/16" x 36 yds.1 1/2" x 1/16" x 36 yds.2" x 1/16" x 36 yds.




We carry a wide selection of

contractor supplies designed

for the professional

contractor. From a full line of

safety equipment to fall

protection, we can supply all

of your job-site needs with

high quality products. These

products are in stock an

available to meet your needs.

• Access Doors• Back Support Belts• Boxes - Jobsite• Coolers - IGLOO• Ear Protection• Fall Protection• First Aid Kits• Gas Cans• Gloves

• Hand Cleaner• Hard Hats• Lanyards• Rags• Respirators• Safety Glasses• Tarps

CONTRACTOR SUPPLIES




278278

CONTRACTOR SUPPLIESCONTRACTOR SUPPLIES

We have a full line of safety products to meet your needs!

Hard HatsSafety Glasses and Shields

Ear Protection

First Aid Kits

Respirators

Call us for all of your miscellaneous contractor supplies!

Gloves

Tarps

Job-site Coolers

Job-site Storage




Slope Lid Box• Fold-away prop supports lid to form large flat working surface at ideal working height.• Taller body provides huge 32.7 cu. ft. of storage space.

Usable Shipping ShippingModel Desc. L W H Cu. Ft. Cu. Ft. Wt. Lbs68090 Slope Lid 60" 30" 39 1/2" 32.7 45.5 225.0

Specifications

• Heavily reinforced 16 gauge steel construction.• The strongest, most durable chests in the industry.• Flat exterior design eliminates exposed handles and improves job

site safety.• Welder’s box model 650990 has a cut-out for storing tools still

connected to fuel tanks. Welded heavy-duty hasp for using padlock. Fold-away lifting handles.

• Model 651990 chest provides portability in a compact. highly secure design.

• 31" long model 811990 portable chest fits small spaces. Includes fold-away handles on each end and high-strength bottom bolsters. Heavy-duty welded hasp for padlock. Lid supported by a chain when open.

Usable Shipping ShippingModel L W H Cu. Ft. Cu. Ft. Wt. Lbs.650990 30" 16" 12" 3.3 4.6 37.0651990 31" 18" 15" 4.0 5.7 54.0811990 30" 18" 14" 4.5 6.0 54.5

Specifications

811990

651990

650990

Heavy Duty Chests

Model Size Shipping Wt.601040 4" 15.0602040 6" 19.0

Heavy duty casters

Set includes a pair of fixed and a pair of swiveling casters.

Piano Boxes

Heavy Duty Casters

• Heavily reinforced 16 gauge steel construction.• Door and body reinforced for superior strength,

rigidity and resistance to break-ins.• Designed for improved resistance to dust and

moisture to protect contents and interior from damage.

Usable Shipping ShippingModel Description L W H Cu. Ft. Cu. Ft. Wt. Lbs.68199O Piano Box 48 7/8" 31 11/32" 49 1/2" 38.0 48.2 260.0682990 Piano Box 60 7/8" 31 11/32" 49 1/2" 47.5 59.2 309.5688990 Piano Box 60 7/8" 30 1/8" 37 11/16" 34.4 44.8 280.0689990 Piano Box 74 7/8" 30 1/8" 49 7/8" 56.5 72 .25 398.0

Specifications

STORAGE BOXESSTORAGE BOXES




280280

Elk River LanyardLanyards serve as the connection between the harness and the anchorage. when using a lanyard, the anchorage should be at least shoulder height. If no compatible anchorage is available, an anchorage connector, such as an EZE-MAN tie-off Sling or D-ring Anchorage Connector, may be used to create a suitable anchorage. It is the wearer's responsibility to make sure that only compatible connectors are used throughout the entire Fall Arrest (PA) system.

Our lanyards are made of either a web material, rope, or metal cable. All lanyards come with connecting hardware on the ends. The lanyard materials are described in more detail on the next page.

Elk River offers lanyards in two main categories: Shock absorbing and Non-shock absorbing types.

Nonshock-Absorbing LanyardsThe Nonshock-Absorbing lanyards are made from either nylon webbing, polyester webbing, or a combination of these two materials, galvanized aircraft cable, nylon rope, or Kevlar® webbing

• 1/4" Galvanized Aircraft Cable• 1" Nylon Webbing• 1-3/4" Polyester Webbing• 1" Eagle™ Nylon Webbing• 5/8" Nylon Rope• 1/2" Nylon Rope• 3/4" Nylon Rope• 1-3/4" KevIar® Webbing

Shock-Absorbing LanyardsThe Shock-Absorbing lanyards are made from the same materials as the nonshock-Absorbing lanyards and have either a ZORBER Shock-Absorbing pouch or an integral shock-absorbing material made into the length of the lanyard.

• 1/4" Galvanized Aircraft Gable with ZORBER• 1" Nylon Webbing with ZORBER • 1-3/4" Polyester Webbing with ZORBER• 1" NoPac™ Webbing• 1-3/8" 2-element Nylon & Polyester Webbing• 1-1/2" Flex-NaPac™ Polyester Webbing• 1" Eagle™ Nylon Webbing with ZORBER • 5/8" Nylon Rope with ZORBER• 1/2" Nylon Rope with ZORBER• 1-3/4" KevIar® Webbing

FALL PROTECTIONFALL PROTECTION




Elk River Roofer's KitsRoofer's Kits are available in several combinations with each kit containing specific items. The combinations listed below are our most popular kits.

Roofer's Kit includes: 55102 Freedom Harness with D-ring at center of back, 34750 5/8" nylon rope lifeline with 13120 3/4" throat opening centurion auto-lock snaphook on one end and thimble on the other end, 19273 5/8" rope grab attached to 1" x 3’ nylon web shock-absorbing lanyard with 13120 3/4" throat opening Centurion snaphook on ZORBER end, 13050 reusable roof anchor with attached D-ring, 88001 Black Roofer's bag.

Roofer's Kit includes: 55104 Freedom Harness with D-ring at center of back, 34750 5/8" nylon rope lifeline with 13120 3/4" throat opening Centurion autoLock snaphook on one end and thimble on the other end, 19273 5/8" rope grab attached to 1" x 3' nylon web shock-absorbing lanyard with 13120 3/4" throat opening Centurion snaphook on ZORBER end, 13050 reusable roof anchor with attached D-ring, 88001 Black Roofer's bag.

FALL PROTECTIONFALL PROTECTION

Contact TFC to choose from a wide selection of safety equipment to meet your needs!




282282

UF-5000Prime Coated Steel

The Acudor UF-5000 is an innovative universal flush access door for walls and ceilings. It is designed for installation in drywall, plaster, masonry, tile or any flush surface. The door panel features rounded safety corners which provide an architecturally pleasing appearance. The one piece trim flange will not rack, sag or distort.

The unique continuous concealed hinge will not bind or corrode, allowing the door to operate freely time and time again. For easy installation, the mounting frame is 1-1/4" deep, giving maximum clearance behind the door frame.

Specifications

Material: 16" X 16" and smaller: 16 gage door, 18 gage mounting frame. Over 16" X 16": 14 gage door, 16 gage mounting frame.

Door: Flush to frame - rounded safety corners.

Frame: One-piece outer frame welded to mounting frame.

Hinge: Continuous, concealed.

Latch: Stainless Steel screwdriver operated cam latch. Also available: cylinder lock and key, allen head cam latch, spanner head cam latch.

Finish: Steel: 5-stage iron phosphate preparation with prime coat of gray baked enamel. Stainless Steel: Type 304 - #4 satin polish.

NOMINAL DOOR SIZE (W & H) WALL OR CEILING OPENING WEIGHT PER DOOR Number of Latches INCHES mm INCHES mm lbs. kg. 6 X 6 152 X 152 6-3/8 X 6-3/8 161 X 161 2.0 0.9 1 8 X 8 203 X 203 8-3/8 X 8-3/8 213 X 213 2.7 1.2 1 8 X 12 203 X 305 8-3/8 X 12-3/8 213 X 314 3.6 1.6 1 10 X 10 254 X 254 10-3/8 X 10-3/8 264 X 264 3.6 1.6 1 12 X 12 305 X 305 12-3/8 X 12-3/8 314 X 314 4.7 2.1 1 12 X 16 305 X 406 12-3/8 X 16-3/8 314 X 416 6.0 2.7 2 12 X 18 305 X 457 12-3/8 X 18-3/8 314 X 467 7.0 3.1 2 12 X 24 305 X 610 12-3/8 X 24-3/8 314 X 619 8.5 3.9 2 14 X 14 355 X 355 14-3/8 X 14-3/8 365 X 365 6.2 2.7 1 16 X 16 406 X 406 16-3/8 X 16-3/8 416 X 416 7.6 3.4 2 16 X 24 406 X 610 16-3/8 X 24-3/8 416 X 619 12.5 5.7 2 18 X 18 457 X 457 18-3/8 X 18-3/8 467 X 467 11.2 5.1 2 18 X 24 457 X 810 18-3/8 X 24-3/8 467 X 619 15.0 6.7 2 22 X 22 560 X 560 22-3/8 X 22-3/8 568 X 568 16.3 7.2 4 22 X 30 560 X 762 22-3/8 X 30-3/8 568 X 772 21.0 9.5 5 24 X 24 610 X 610 24-3/8 X 24-3/8 619 X 619 18.0 8.2 4 24 X 30 610 X 762 24-3/8 X 30-3/8 619 X 772 22.5 10.2 5 24 X 36 610 X 914 24-3/8 X 36-3/8 619 X 924 26.6 12.1 5 24 X 48 610 X 1220 24-3/8 X 48-3/8 619 X 1229 38.0 18.1 5 30 X 30 762 X 762 30-3/8 X 30-3/8 772 X 772 27.5 12.5 5 36 X 36 914 X 914 36-3/8 X 36-3/8 924 X 924 39.0 17.7 5

STANDARD SIZES (special sizes available upon request)

ACCESS DOORSACCESS DOORS




DW-5040Prime Coated Steel

The Acudor DW-5040 is designed specifically for installation in drywall walls and ceilings after drywall has been installed.

The flange of the door is a textured galvanized steel taping bead with pre-punched holes. Drywall compound is applied over the beading at the same time the drywall joints are finished. When the application is completed, only the door panel remains exposed. Our unique concealed hinge and screwdriver operated cam latches allow the door panel to operate freely with no binding, sagging or distortion.

Specifications

Material: Steel or Stainless Steel: 14 gage door, 14 gage mounting frame.

Door: Flush to edge of frame

Frame: Galvanized steel drywall taping bead on all sides

Hinge: Continuous, concealed.

Latch: Stainless Steel screwdriver operated cam latch. Also available: cylinder lock and key, allen head cam latch, spanner head cam latch.

Finish: Steel: 5-stage iron phosphate preparation with prime coat of gray baked enamel. Stainless Steel: #4 satin polish.

NOMINAL DOOR SIZE (W & H) WALL OR CEILING OPENING WEIGHT PER DOOR Number of Latches INCHES mm INCHES mm lbs. kg. 8 X 8 203 X 203 8-3/8 X 8-3/8 213 X 213 3.5 1.5 1 10 X 10 254 X 254 10-3/8 X 10-3/8 264 X 264 4.5 2.0 1 12 X 12 305 X 305 12-3/8 X 12-3/8 314 X 314 6.0 2.7 1 14 X14 355 X 355 14-3/8 X 14-3/8 365 X 365 7.5 3.3 1 16 X 16 406 x 406 16-3/8 X 16-3/8 416 X 416 9.5 4.2 2 18 X 18 457 X 457 18-3/8 X 18-3/8 467 X 467 11.5 5.1 2 22 X 22 560 X 560 22-3/8 X 22-3/8 568 X 568 15.0 6.7 4 24 X 24 610 X 610 24-3/8 X 24-3/8 619 X 619 19.0 8.4 4 24 X 36 610 X 914 24-3/8 X 36-3/8 619 X 924 28.0 12.4 5






284284

HD-5070Acudor Duct Access Doors are designed to provide convenient, economical access to duct components. The insulated door panel, along with the gasketing between the door and frame assures a tight seal without obstruction in the air system. Acudor duct access doors are available in either hinged (HD-5070) or double cam (CD-5080) construction.

Specifications

Door: 24 gage galvanized steel, double panel.

Frame: 24 gage galvanized steel with 5/8" notched knock over tabs.

Hinge: Continuous aluminum piano hinge. (HD-5070 only)

Insulation: Door panel filled with 2" fiberglass insulation (7.7 R factor), compressed into 1".

Gasketing: 1/8" thick by 1/2" wide closed cell neoprene gasketing between door and frame.

Latch: Self-tightening, hand operated cam latch.

NOMINAL DOOR SIZE (W & H) DUCT OPENING WEIGHT PER DOOR INCHES mm INCHES lbs. kg. 6 X 6 150 X 150 4-3/4 X 4-3/4 1.25 0.6 8 X 8 200 X 200 6-3/4 X 6-3/4 1.75 0.8 10 X 10 250 X 250 8-3/4 X 8-3/4 2.75 1.3 12 X 12 300 X 300 10-3/4 X 10-3/4 3.75 1.7 14 X 14 350 X 350 12-3/4 X 12-3/4 4.75 2.2 16 X 16 400 X 400 14-3/4 X 14-3/4 5.25 2.4 18 X 18 450 X 450 16-3/4 X 16-3/4 6.75 3.1 20 X 20 500 X 500 18-3/4 X 18-3/4 9.00 4.1 24 X 24 610 x 610 22-3/4 X 22-3/4 12.00 5.5


Rear View





The purpose of this guide is to provide the most comprehensive fastening systems information available to the industry. We have included many standard and hard to find specialty products.

You will find technical information on the majority of the fasteners listed. Additionally, we have developed this section to include general information on fasteners, coatings, corrosion and stainless steel.

DISCLAIMERSWe have taken great care in compiling this information and made an effort to present its content accurately. However, TFC is not responsible for any claims traceable to any errors (typographical or otherwise) as contained in this guide.

THE USE OF THIS GUIDE IS FOR GENERAL INFORMATION ONLY, AND CANNOT BE CONSTRUED AS A SUBSTITUTE FOR COMPETENT PROFESSIONAL ADVICE OR SERVICE. ANY PARTY CONSIDERING APPLICATION OR USE OF THIS INFORMATION DOES SO AT THEIR OWN RISK AND ASSUMES ANY AND ALL LIABILITY ARISING FROM ITS APPLICATION OR USE.

TECHNICALINFORMATION

Technical Data . . . . . . . . . . . . . . . . . . . . 285 ACQ Treated Lumber Information . . 301 Bolt Strength . . . . . . . . . . . . . . 294, 295 Corrosion . . . . . . . . . . . . . . . . . 297-299 Drive Systems . . . . . . . . . . . . . . . . . 287 Fastener Properties . . . . . . . . . . . . . 286 Galvanic Corrosion Chart . . . . . . . . . 299 Grade Markings . . . . . . . . . . . . . . . . 293 Head Styles . . . . . . . . . . . . . . . . . . . 287

Hole Sizes for Tapping Screws . . . . 291 Nut Strengths . . . . . . . . . . . . . . . . . . 296 Plating . . . . . . . . . . . . . . . . . . . 298, 300 Point Types . . . . . . . . . . . . . . . 289, 290 Self-Drilling Screw General Data . . . 292 Shoulder Types . . . . . . . . . . . . . . . . 288 Stainless Steel . . . . . . . . . . . . . 302, 303 Thread Type . . . . . . . . . . . . . . . . . . . 290 Torsional Strength . . . . . . . . . . 291, 292

Washer Types . . . . . . . . . . . . . . . . . 288




286286

Fastener PropertiesPhysical, mechanical and performance characteristics are material related properties which collectively give the fastener its service capability.

Physical PropertiesInherent in the raw material and remain unchanged or only slightly altered in the fastener after its manufacture.

Mechanical PropertiesIdentify the reaction of a fastener to applied loads. Properties such as hardness, ductility and tensile and yield strengths are all subject to significant change as the raw material is processed into a finished fastener.

Performance PropertiesFunctional design features manufactured into the fastener to assist it to satisfy various service requirements. Properties of this type include prevailing torque, driving torque, locking ability and sealing. Choice of material and its metallurgical treatment influence magnitude rather than the presence of a particular performance property.

Mechanical PropertiesTensile Strength - The maximum tension applied load a fastener can support prior to fracture.

Yield Strength - A tension applied load at which a fastener experiences a specified amount of permanent deformation: i.e., the material has been stressed beyond its elastic limit and has entered its plastic zone.

Proof Load - The tension applied load supported by the fastener without evidence of permanent deformation (about 90-93% of expected material yield).

Hardness - A measure of ability to resist abrasion and indentation. For carbon steel fasteners there is a close correlation between hardness and tensile strength. A similar pattern exists for stainless and non-ferrous materials, but it is not as precise as for carbon steels.

Ductility - Ability of a material to deform before it fractures. Elongation and reduction of area are common criteria to evaluate ductility.

Toughness - A material's ability to resist damage when stressed by impact or shock loading. Impact strength testing is rarely a testing requirement outside of aerospace applications.

Shear Strength - The maximum load applied normal to a fastener's axis that can be supported prior to fracture. Single shear is load occurring in one transverse plane, thus cutting the fastener into two pieces. Double shear is load applied in two planes, so that the fastener would be cut into three pieces.

Torsional Strength - Load usually expressed in terms of applied torque at which fastener fails by being twisted off about its axis. The torsional strength of the driving recess or wrenching surface is the torque which can be sustained without damage to the tool/fastener interface resulting in an undriveable condition.

Fatigue Strength - The maximum load a fastener can withstand for a specified number of repeated applications prior to failure. For a single load application to failure, the fatigue strength equals the static tensile strength. As the load is reduced, the fastener endures an increasing number of loading cycles until it reaches its other extreme of fatigue strength known as its endurance limit, which is the cyclic load the fastener can accept and survive indefinitely. Rarely used outside of aerospace applications, but helps compare relative performance to resist dynamic loadings.

FASTENER PROPERTIESFASTENER PROPERTIES




Drives

Slotted One-Way Slot

Phillips (Type 1)

Phillips /Slot Combination

Phillips(Type 1A)

1A/SlotCombination

Phillips/Hex

Frearson (Type 2)

Quadrex®(Square/Phillips)

Square 6 Lobe(torx)

Hex Socket

Hex Washer

Hex

Binder Head

Button Head

Bugle Head

Cheese Head

Ext 6 Lobe Washer Head

Fillister Head

82˚ Flat Countersunk

82˚ U/C Countersunk



Ind Hex Head

Trimmed Hex Head

Trimmed Acorn

Hex Cap Screw

Hex Washer

Ind Hex Flange Head

82˚ Oval Head

90˚ Oval Head

82˚ Oval U/C Head

90˚ Oval U/C Head

Pan Head (for slottedpan heads)

Pan Head (for recessedpan heads)

Pan Head (for socket product)

Round Head Round Head

Square NeckFull Crown

Round Washer Head

Flat Top Round

Washer Head

Socket Head

Knurled Head

Full Crown Truss Head

Flat Top Truss Head

Type UR Pancake Head

Head Styles

DRIVES AND HEAD STYLESDRIVES AND HEAD STYLES




288288

Under Head Configurations

Full Serrations

Reduced Body

Knurled Shoulder

Ribbed Neck

Square Shoulder

Square Neck

Shoulder Full Body

Full Reverse Serrations

Spinlock Serrations

6 “Nibs" Serrations

Partial Serrations

Chevron Serrations

BlankDia.

Washers

Beveled Conical External External Contersunk

Internal

Internal / External

Flat Slit Lock Split Wave Wave Washer

Ramp Conical Pyramidal Square® Cone Finishing Flanged Finishing

Thread

Dia.

HEAD FEATURES AND HEAD FEATURES AND WASHERSWASHERS




Point Styles

A

BP T-Lobe B 25 (BT) Pilot Point Header Point

1 (D)

Fetter Oval Point Cup Point Dog Point Pilot Point Cone Point

17 AB 22˚ Point B

23 (T) F Type CA T-Lobe CA PF25

POINT TYPESPOINT TYPES




290290

Pictorial ANSI/ASME Manufacturer's Representation Designation Designation

AB AB

B B

BP BP

BF BF

BT 25

C C

D 1

F F

G G

T 23

U U

Type Designations for Tapping Screws and Metallic Drive ScrewsAbstract of ANSI/ASME B18.6.4 1981

Not recommended for new designs

TAPPING SCREW TAPPING SCREW POINTSPOINTS




Suggested hole sizes for tapping screws

Nominal Hole Closest Drill Size to Screw Size Diameter Mean Hole Diameter Max Mean Min Drill Size Drill Dia. 2 - 56 0.078 0.076 0.074 48 0.076 2-64 0.077 3 -48 0.090 0.087 0.084 44 0.086 3-56 0.089 4 - 40 0.100 0.097 0.094 41 0.096 4-48 0.100 5-40 0.113 0.110 0.107 35 0.110 5-44 0.112 6-32 0.123 0.119 0.115 31 0.120 6-40 0.124 8-32 0.150 0.146 0.141 20 0.147 8-36 0.148 10 - 24 0.170 0.165 0.160 19 0.166 10-32 0.177 0.172 0.167 11/64 0.1719 12-24 0.198 0.192 0.186 11 0.191 12-28 0.196 1/4 - 20 0.228 0.221 0.214 2 0.221 1/4-28 0.230 5/16 - 18 0.289 0.281 0.273 K 0.281 5/16-24 0.290 3/8 - 16 0.349 0.339 0.329 R 0.339 3/8 - 24 0.353 7/16 - 14 0.409 0.397 0.385 X 0.397 7/16-20 0.411 1/2 - 13 0.471 0.457 0.443 29/64 0.4531 1/2 - 20 0.475

FormulaMean Hole Dia = 1.015 x basic thread pitch diameter. Tolerance is plus and minus 3 percent of mean hole dia. No tolerances or drill sizes are given for tapping screws with fine threads except for the No. 10 size. Use of fine thread tapping screws is not encouraged.

Table 1 Suggested Hole Sizes for ThreadRolling Tapping Screws and Types D, F, G and T

Thread Cutting Tapping Screws

Table 2 Suggested Hole Sizes for Types AB, B, and BP Thread Forming Tapping Screws and Types BF

and BT Thread Cutting Tapping Screws

Nominal Hole Closest Drill Size to Screw Size Diameter Mean Hole Diameter Max Mean Min Drill Size Drill Dia. 0-48 0.049 0.046 0.043 56 0.0465 1-42 .063 .059 .055 53 .0595 2 - 32 .077 .072 .067 49 .073 3-28 .090 .084 .078 45 .082 4-24 .103 .096 .089 41 .096 5-20 .114 .107 .100 36 .1065 6-20 .124 .116 .108 32 .116 7-19 .138 .129 .120 30 .1285 8 - 18 .148 .138 .128 29 .136 10-16 .170 .159 .148 21 .159 12-14 .194 .182 .169 14 .182 1/4-14 226 .211 .196 4 .209 5/16-12 .289 .270 .251 I .272 3/8-12 .356 .333 .310 0 .332 7/16-10 .413 .386 .359 w .386 1/2 - 10 .480 .449 A18 29/64 A531

FormulaMean Hole Dia = 0.98 x mean of thread major and minor diameters. Tolerance is plus and minus 7 percent of mean hole dia.

Minimum Torsional Strength, lb-in. Nominal Types AB, B, BF, T ypes C, D, F, G and T Screw Size HP and BT Coarse Fine Thread Thread 2 4 5 6 3 9 9 10 4 13 13 15 5 18 18 20 6 24 23 27 7 30 – – 8 39 42 47 10 56 56 74 12 88 93 108 1/4 142 140 179 5/16 290 306 370 3/8 590 580 710 7/16 620 700 820 1/2 1020 1075 1285

Torsional Strength Requirements For Tapping Screws

Typical Torsional Strength Test Fixture

NoteAs a general practice, tapping torque should equal approximately 70% of the fasteners torsional strength.

HOLE SIZES FORHOLE SIZES FORTAPPING SCREWSTAPPING SCREWS




292292

Type BSD Type CSD Types BSD and CSD Nominal Size D d z D z L or Basic Threads Major Minor Protrusion Threads Major Protrusion Minimum Practical Nominal Screw Lengths (Ref) Screw Diameter Per inch Diameter Diameter Allowance (Ref) Per inch Diameter Allowance (Ref) Style 2 Points Style 3 Points Formed Milled Formed Milled Max Mm Max Mm Style 2 Style 3 Max Mm Style 2 Style 3 90 deg Csk 90 deg Csk 90 deg Csk 90 deg Csk Point Point Point Point Heads Heads Heads Heads Heads Heads Heads Heads 4 0.1120 24 0.114 0.110 0.086 0.082 0.163 - 40 0.1120 0.1072 0.130 - 5/16 3/8 3/8 7/16 - - - - 6 0.1380 20 0.139 0.135 0.104 0.099 0.190 0.220 32 0.1380 0.1326 0.152 0.172 5/16 3/8 3/8 7/16 3/8 7/16 7/16 1/2 8 0.1640 18 0.166 0.161 0.122 0.116 0.211 0.251 32 0.1640 0.1586 0.162 0.202 3/8 7/16 7/16 1/2 7/16 1/2 1/2 9/16 10 0.1900 16 0.189 0.183 0.141 0.135 0.235 0.300 24 0.1900 0.1834 0.193 0.258 7/16 1/2 15/32 19/32 1/2 9/16 9/16 21/32 12 0.2160 14 0.215 0.209 0.164 0.157 0.283 0.353 24 0.2160 0.2094 0.223 0.293 1/2 5/8 17/32 21/32 1/2 5/8 21/32 25/32 1/4 0.2500 14 0.246 0.240 0.192 0.185 0.318 0.393 20 0.2500 0.2428 0.275 0.350 1/2 5/8 17/32 11/16 1/2 5/8 11/16 27/32 See Note2 3 3

Nominal Screw Size Minimum Torsional Strength, lb-in Hydrogen Embrittlement Test Torque, lb-in Type BSD Type CSD Cadmium Plated Screws Zinc Plated Screws Types BSD and CSD Types BSD and CSD 4 14 14 10.5 12 6 24 24 18 20 8 42 48 36 41 10 61 65 49 55 12 92 100 72 85 1/4 150 156 114 132

Mechanical and Performance Requirements for Types BSD and CSD Self-Drilling Tapping Screws

SAE J78 Specifications

Dimensions of Threads and Points for Types BSD and CSD Self-Drilling Tapping Screws

NOTES:

1. Drill portion of points may be milled and/or cold formed and details of point taper and flute design shall be optional with the manufacturer, provided the screws meet the performance requirements specified in this standard and are capable of drilling the maximum panel thicknesses shown in Table 5 prior to thread pickup.

2. Where specifying nominal size in decimals, zeros preceding decimal and in fourth decimal place shall be omitted.

3. Protrusion allowance Z Is the distance, measured parallel to the axis of screw, from the extreme end of the point to the first full form thread beyond the point and encompasses the length of drill point and the tapered incomplete threads. It is intended for use In calculating the maximum effective design grip length Y on the screw in accordance with the following:

Y = L Min - Z

Major Diameter Protrusion Allowance

See Note 1

BSD = Coarse Thread (Type B Thread) CSD = Fine Thread (T ype C Thread)

For pullout data, refer to page 16-17 in TFC Fastening Systems Guide.

SELF-DRILLING TAPPING SELF-DRILLING TAPPING SCREW INFORMATION SCREW INFORMATION




Grade Identification Specification Material Nominal Proof Load Tensile Strength Hardness See Marking Size in. Stress ksi Min ksi Rockwell Note Min Max SAE J429 - Grade 1 Low or Medium Carbon Steel 1/4 thru 1 1/2 33 60 B7O B100 SAE J429 - Grade 2 1/4 thru 3/4 over 55 74 B80 B100 over 3/4 thru 1 1/2 33 60 B70 B100 ASTM A307 - Grade A 1/4 thru 4 – 60 B69 B100 ASTM A307 - Grade B 1/4 thru 4 – 60 Min B69 B95 – 100 Max SAE J429 - Grade 5 Medium Carbon Steel, 1/4 thru 1 over 85 120 C25 C34 ASTM A449 - Type 1 Quenched and Tempered 1 thru 1 1/2 74 105 C19 C30 ASTM A449 - Type 1 over 1 1/2 thru 3 55 90 183 235 3

Low or Medium Carbon Steel, SAE J429 - Grade 5.1 Quenched and Tempered N0.6 Thru 1/2 85 120 C25 C40 4

SAE J429 - Grade 5.2 Low Carbon Martensite Steel, C26 C36 ASTM A449 - Type2 Quenched and Tempered 1/4 thru 1 85 120 C25 C34

ASTM A325 - Type 1 Medium Carbon Steel 5 Quenched and Tempered

ASTM A325 - Type 2 Low Carbon Martensite 1/2 Thru 1 85 120 C24 C35 Steel, Quenched and Tempered over 1 to 1 1/2 74 105 C19 C31 Atmospheric Corrosion Resistant ASTM A325 - Type 3 Steel, Quenched and Tempered 6

Medium Carbon Alloy Steel, 1/4 thru 2 1/2 105 125 C26 C36 ASTM A354 - Grade BC Quenched and Tempered over 2 1/2 thru 4 95 115 C22 C33

SAE J429 - Grade 8 Medium Carbon Alloy Steel, 1/4 thru 1 1/2 120 150 C33 C39 ASTM A354 - Grade BD Quenched and Tempered 1/4 thru 2 1/2 over 120 150 C33 C39 2 1/2 thru 4 105 140 C31 C39 7

Low Carbon Martensite Alloy SAE J429 - Grade 8.2 Steel, Quenched and Tempered 1/4 thru 1 120 150 C33 C39

ASTM A490 - Type 1 Medium Carbon Alloy Steel, 150 Min Quenched and Tempered 1/2 Thru 11/2 120 170 Max C33 C38

ASTM A490 - Type 2 Low Carbon Martensite Steel, 1/2 Thru 1 120 150 Min C33 C38 Quenched and Tempered 170 Max

ASTM A490 - Type 3 Atmospheric Corrosion Resistant 150 Min Steel, Quenched and Tempered 1/2 Thru 1 120 170 Max C33 C38 6

Grade Identification Markings for Carbon Steel Externally Threaded Fasteners

1. In addition to the indicated grade marking, all grades included in this Table must be marked for manufacturer identification.2. While hex heads are shown, grade markings apply equally to products with other head configurations.3. Hardnesses are Brinell Hardness Numbers.4. Grade 5.1 is a popular grade for sems5. A325 Type 1 bolts may also be marked with 3 radial lines 1200 apart in addition to the A325 marking.6. The bolt manufacturer, at his option, may add other markings to indicate the use of atmospheric corrosion resistant steel.7. A354 Grade BD products, in sizes 11/2 in. and smaller, are identified as shown and, at the manufacturers option, may have the letters BD added. Larger sizes are marked only BD.

A325

A325

A325

BC

A490

A490

A490

NOTES:

No Mark

BOLT STRENGTHSBOLT STRENGTHS




294294

Nominal Dia Stress Grade 1 Grade 2 Grade 4 Grades 5 and 5.2B Grade 5.1 Grade 7 Grades 8, 8.1,8.2B

of Product Area, Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile and Threads in.2 Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength per in. lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb

Coarse Thread Series - UNCNo. 6-32 0.00909 - - - - - - 750 1,100 - - - - 8-32 0.0140 - - - - - - 1,200 1,700 - - - - 10-24 0.0175 - - - - 1,500 2,100 - - - - 12-24 0.0242 - - - - - - 2,050 2,900 - - - - 1/4-20 0.0318 1,050 1,900 1.750 2,350 2,050 3,650 2,700 3,800 2,700 3,800 3,350 4,250 3,800 4,750 5/16-18 0.0524 1,750 3,150 2,900 3,900 3,400 6,000 4,450 6,300 4,450 6,300 5,500 6,950 6,300 7,850 3/8-16 0.0775 2,550 4,650 4,250 5,750 5,050 8,400 6,600 9,300 6,600 9,300 8,150 10,300 9,300 11,600 7/16-14 0.1063 3,500 6,400 5,850 7,850 6,900 12,200 9,050 12,800 9,050 12,800 11,200 14,100 12,800 15,900 1/2-13 0.1419 4,700 8,500 7,800 10,500 9,200 16,300 12,100 17,000 12,100 17,000 14,900 18,900 17,000 21,300 9/16-12 0.182 6,000 10,900 10,000 13,500 11,800 20,900 15,500 21,800 15,500 21,800 19,100 24,200 21,800 27,300 5/8-11 0.226 7,450 13,600 12,400 16,700 14,700 25,400 19,200 27,100 19,200 27,100 23,700 30,100 27,100 33,900 3/4-10 0.334 11,000 20,000 18,400 24,700 21,700 38,400 28,400 40,100 - - 35,100 44,400 40,100 50,100 7/8-9 0.462 15,200 27,700 15,200 27,700 30,000 53,100 39,300 55,400 - - 48,500 61,400 55,400 69,300 1-8 0.606 20,000 36,400 20,000 36,400 39,400 69,700 51,500 72,700 - - 63,800 80,600 72,700 90,900 1-1/8-7 0.763 25,200 45,800 25,200 45,800 49,600 87,700 56,500 80,100 - - 80,100 101,500 91,600 114,400 1-1/4-7 0.969 32,000 58,100 32,000 58,100 63,000 111,400 71,700 101,700 - - 101,700 127,700 116,300 145,400 1-3/8-6 1.155 38,100 69,300 38,100 69,300 75,100 132,800 85,500 121,300 - - 121,300 153,600 138,600 173,200 1-1/2-6 1.405 46,400 84,300 46,400 84,300 91,300 161,600 104,000 147,500 - - 147,500 186,900 168,600 210,800

Fine Thread Series - UNFNo. 6-40 0.01015 - - - - - - - - 850 1,200 - - - - 8-38 0.01474 - - - - - - - - 1,250 1,750 - - - - 10-32 0.0200 - - - - - - - - 1,700 2,400 - - - - 12-28 0.0258 - - - - - - - - 2,200 3,100 - - - - 1/4-28 0.0364 1,200 2,200 2,000 2,700 2,350 4,200 3,100 4,350 3,100 4,350 3,800 4,850 4,350 5,450 5/16-24 0.0580 1,900 3,500 3,200 4,300 3,750 6,700 4,900 6,950 4,900 6,950 6,100 7,700 6,950 8,700 3/8-24 0.0878 2,900 5,250 4,800 6,500 5,700 10,100 7,450 10,500 7,450 10,500 9,200 11,700 10,500 13,200 7/16-20 0.1187 3,900 7,100 6,550 8,800 7,700 13,650 10,100 14,200 10,100 14,200 12,500 15,800 14,200 17,800 1/2-20 0.1599 5,300 9,600 8,800 11,800 10,400 18,400 13,600 19,200 13,600 19,200 16,800 21,300 19,200 24,000 9/16-18 0.203 6,700 12,200 11,200 15,000 13,200 23,300 17,300 24,400 17,300 24,400 21,300 27,000 24,400 30,400 5/8-18 0.256 8,450 15,400 14,100 18,900 16,600 29,400 21,800 30,700 21,800 30,700 26,900 34,000 30,700 38,400 3/4-16 0.373 12,300 22,400 20,500 27,600 24,200 42,900 31,700 44,800 - - 39,200 49,600 44,800 56,000 7/8-14 0.509 16,800 30,500 16,800 30,500 33,100 58,500 43,300 61,100 - - 53,400 67,700 61,100 76,400 1 -12 0.663 21,900 39,800 21,900 39,800 43,100 76,200 56,400 79,600 - - 69,600 88,200 79,600 99,400 1-1/4 uns 0.679 22,400 40,700 22,400 40,700 44,100 78,100 57,700 81,500 - - 71,300 90,300 81,500 101,900 1-1/8-12 0.856 28,200 51,400 28,200 51,400 55,600 98,400 83,300 89,900 - - 89,900 113,800 102,700 128,400 1-1/4-12 1.073 35,400 64,400 35,400 64,400 69,700 123,400 79,400 112,700 - - 112,700 142,700 128,800 161,000 1-3/8-12 1.315 43,400 78,900 43,400 78,900 85,500 151,200 97,300 138,100 - - 138,100 174,900 157,800 197,200 1-1/2-12 1.581 52,200 94,900 52,200 94,900 102,800 181,800 117,000 116,000 - - 166,000 210,300 189,700 237,200

PROOF LOAD AND TENSILE STRENGTH REQUIREMENTS (a)

A) Proof loads and tensile strengths are computed by multiplying the proof load stresses and tensile strength stresses given in Table 1 by the stress area of the thread.

The stress area of sizes and thread series not included in this table may be computed from the formula: As = 0.7854 [D- ]2 where D equals nominal diameter in inch, and n equals threads per inch.

B) Grades 5.2 and 8.2 applicable to sizes 1/4 through 1 in.

0.9743n

CARBON STEEL BOLTSCARBON STEEL BOLTSPROOF AND TENSILE STRENGTHSPROOF AND TENSILE STRENGTHS




Mechanical Requirements Bolts1 Screws And Studs Full Size Bolts, Machined Test Specimens Of Nuts Screws, Studs Bolts, Screws, Studs Yield2 Tensile Yield2 Tensile Hardness Proof Load Hardness General Strength Strength Strength Strength Elongation3 Rockwell Stress Rockwell Grade1 Description min ksi min ksi min ksi min ksi % Min Min ksi Min Austenitic 303-A Stainless Steel 30 75 30 75 20 B75 75 B75 Sot. Annealed Austenitic 304-A Stainless Steel 30 75 30 75 20 B75 75 B75 Sol. Annealed Austenitic 304 Stainless Steel 50 90 45 85 20 B85 90 B85 Cold Worked 305-A Stainless Steel 30 75 20 75 20 B70 75 B70 Sol. Annealed Austenitic 305 Stainless Steel 50 90 45 85 20 B85 90 B85 Cold Worked Austenitic 316-A Stainless Steel 30 75 30 75 20 B70 75 B70 Sol. Annealed Austenitic 316 Stainless steel 50 90 45 85 20 B85 90 B85 Sol. Annealed Austenitic 316-SH Stainless Steel See See See See 15 C25 See C20 Strain Hardened Note 6 Note 6 Note 6 Note 6 Note 6 410-H Stainless Steel 95 125 95 125 20 C22 125 C22 Hardened and Tempered 410-HT Martensitic Stainless Steel 135 180 135 180 12 C36 180 C36 Hardened and Tempered 416-H Martensitic Stainless Steel 95 125 95 125 20 C22 125 C22 Hardened and Tempered 416-HT Martensitic Stainless Steel 135 180 135 180 12 C36 150 C36 Hardened and Tempered 430 Ferritic Stainless Steel 40 70 40 70 20 B75 70 B75

MECHANICAL REQUIREMENTS FOR STAINLESS STEEL BOLTS, SCREWS, STUDS AND NUTS

STAINLESS STEEL BOLTS & NUTSSTAINLESS STEEL BOLTS & NUTSPROOF AND TENSILE STRENGTHSPROOF AND TENSILE STRENGTHS




296296

Grade Identification Specification Material Nominal Proof Load Hardness See Marking Size in. Stress ksi Rockwell Note Min Max ASTM A 563 - Grade 0 Carbon Steel 1/4 thru 1 1/2 69 B55 C32 3, 4 ASTM A 563 - Grade A Carbon Steel 1/4 thru 1 1/2 90 B68 C32 3, 4 ASTM A 563 - Grade B Carbon Steel 1/4 thru 1 120 B55 C32 3, 4 over 1 thru 1 1/2 105

ASTM A563 - Grade C Carbon Steel, May Be Quenched and Tempered 1/4 thru 4 144 B78 C38 5

ASTM A563 - Grade C3 Atmospheric Corrosion Resistant Steel.May Be Quenched and Tempered 1/4 thru 4 144 B78 C38 5.9

ASTM A563 - Grade D Carbon Steel, May Be Quenched and Tempered 1/4 thru 4 150 B84 C38 6

ASTM A563 - Grade DH Carbon Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 6

ASTM A563 - Grade DH3 Atmospheric Corrosion Resistant Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 5, 9

ASTM A194 - Grade 1 Carbon Steel 1/4 thru 4 130 B70 - 7

ASTM A194 - Grade 2 Medium Carbon Steel 1/4 thru 4 150 159 352 78

ASTM A194 - Grade 2H Medium Carbon Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

ASTM A194 - Grade 2HM Medium Carbon Steel, Quenched and Tempered 1/4 thru 4 150 159 237 7, 8

ASTM A194 - Grade 4 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

ASTM A194 - Grade 7 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

ASTM A194 - Grade 4 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 150 159 237 7

See note 1,2,10

GRADE IDENTIFICATION MARKINGS FOR POPULAR GRADES OF CARBON STEEL NUTS

1. In addition to the indicated grade marking, all grades, except AS63 grades 0, A and B, must be marked for manufacturer identification.2. The markings shown for all grades of A194 nuts are for cold formed and hot forged nuts. When nuts are machined from bar stock the nut must be additionally marked with the letter 'B'.3. Nuts are not required to be marked unless specified by the purchaser. When marked, the identification marking shall be the grade letter 0, A or B.4. Properties shown are those of non-plated or non-coated coarse thread hex nuts.5. Properties shown are those of coarse thread heavy hex nuts.6. Properties shown are those of coarse thread heavy hex nuts.7. Properties shown are those of coarse and 8-pitch thread heavy hex nuts.8. Hardnesses are Brinell Hardness Numbers.9. The nut manufacturer; at his option, may add other markings to indicate the use of atmospheric corrosion resistant steel.10. Specifications - ASTM A563 - Carbon and Alloy Steel Nuts / ASTM A194 - Carbon and Alloy Steel Nuts for Bolts for High Pressure and High Temperature Service

3

DH

DH3

1

2

2H

2HM

4

7

7M

NOTES:

No Mark

CARBON STEEL NUTSCARBON STEEL NUTSPROOF LOADS AND HARDNESSPROOF LOADS AND HARDNESS




Interacting Influences

This brief look at the rusting of steel points up the interacting influences which initiate, and control, the mechanism of electrochemical corrosion.

First, there must be the possibility for any electrical current to flow. This means either the contacting of dissimilar metals with different electropotentials, or some measure of heterogeneity in the same base metal. The greater the differential, the stronger the current flow and the faster and more severe the corrosive action. Corrosion of the same metal, for example; the rusting of steel, normally results in a uniform corroding of the entire exposed surface When dissimilar metals contact, the attack is usually more localized.

Second, there must be an electrolyte a medium through which the electrical current flows. Electrolytes occur naturally in our everyday environments - humidity, fog, dew, condensation, rain - and with a broad variation in their occurrence and intensity. For example, the corrosion survival expectancy of steel is shortened considerably when exposed in the high humidity Southern states as opposed to the ultra-dry desert climates of Nevada and Arizona. Similarly, structures and equipment survive longer in rural Midwestern states than in either ocean bordering states or in heavily industrialized areas with their high impurity atmospheres. Even in the home, storing articles in the dryness of an attic is more protective than in the dampness of a basement.

Distilled water is a poor conductor; tap water with its modest chemical content is better; industrial exposures with their pollutants and contaminants are even better; and salt water is exceptionally good. Whenever the electrolyte is agitated, such as flowing water, its conductivity is significantly magnified. The "dirtier" the electrolyte, the better its conductivity, and the faster the rate of corrosion.

Third, there must be oxygen. As most products of corrosion are oxides formed by the chemical reaction, the presence of oxygen is mandatory. Without oxygen, most forms of corrosion would be stalemated. However, its complete elimination is an engineering impracticality. Oxygen is the principal element of the air we breathe, and it is present, although to a lesser degree, underground and underwater

The importance of oxygen can be illustrated by considering an oceangoing steel-hulled ship. Without suitable protection of its exposed surfaces, the entire hull would corrode, but at three different rates. The plates at the water line would go first because of the concentrated aggressiveness of the sea water coupled with unlimited oxygen. The upper structure and decks would corrode more slowly because the electrolyte is now a spray which has lost some of its intensity although the oxygen supply is undiminished. The fully submerged bottom of the hull would survive the longest simply because of the meagerness of the oxygen supply.

Temperature, while not a direct contributor to corrosion, is definitely a

factor in the rate at which it occurs. Generally, heat accelerates chemical reactions. All other conditions being equal, corrosion happens quicker and more markedly in southern climates than in those of the north. It also

occurs more quickly in industrial plants where heat is inherent in the process as opposed to industries which conduct their operations at ambient temperatures or in the luxury of an air conditioned atmosphere.

Galvanic Corrosion

Similar metals are compatible; dissimilar metals are not. When dissimilar metals contact in the presence of an electrolyte, a galvanic action occurs which causes one of the metals to corrode at a much faster than normal rate, while the other corrodes more slowly, if at all. The rate, location and extent of the corrosion depends on three factors:

• The difference in electrical potentials• The conductivity strength of the corroding medium, and• The relative sizes of the contacting areas.

All metals have electrical potentials. Through research, the potentials of different base metals and their alloys, when exposed to sea water, were measured and then ranked into a series. In an electrical couple, the metal of higher electrical potential is the cathode (-), that of the lower the anode (+). Current flows from the cathode to the anode, from the anode through the electrolyte (corroding medium), and back to the cathode. Corrosion occurs at the point the current leaves the anode to enter the electrolyte. When dissimilar metals contact, the anode corrodes, the cathode survives.

Galvanic Series

Table 1 presents the Galvanic Series of Metals and Alloys. The various metals are grouped. Those within the same group are reasonably compatible when used together; those from different groups cause a corrosion problem. Some metals, basically those with significant contents of nickel and chromium, are included in the Series both in their active and passive conditions. Passivation (surface cleaning and sealing) lowers the metal's electrical potential and improves its corrosion behavior.

Study of the Galvanic Series suggests that steel and aluminum are reasonably compatible; but, if titanium and aluminum contact, the aluminum, as the anode, will corrode Fig. 2 illustrates another example A copper plate is joined to an aluminum plate using a carbon steel bolt. If none of the contacting surfaces are protected, corrosion will occur. The bolt, where it touches the copper, will corrode severely. However, the bolt, where it contacts the aluminum, will not corrode, because it is now the cathode. The aluminum plate in contact with the bolt may corrode, but only slightly because of the minor difference in their electropotentials and the large anode-to-Cathode area ratio. The aluminum plate will corrode where its exposed exterior surfaces contact the copper plate The aluminum plate may also corrode on its interior surface, but not to the same degree, because the corroding medium and oxygen supply are largely sealed out due to the bolt's clamping action.

+Corroded End (anodic, or least noble)Magnesium, Magnesium alloys, Zinc

Aluminum 1100, Cadmium, Aluminum 2024-T4, Steel or Iron, Cast Iron, Chromium-iron (active),

Ni-Resist cast ironType 304 Stainless (active), Type 316 Stainless (active)

Lead tin solders, Lead, TinNickel (active), Inconel nickel-chromium alloy (active), Hastelloy Alloy c (active)

Brasses, Copper, Bronzes, Copper-nickel alloys, Monel nickel-copper alloySilver solder, Nickel (passive), Inconel nickel-chromium alloy (passive)

Chromium-iron (passive), Type 304 Stainless (passive), Type 316 Stainless (passive), Hastelloy Alloy C (passive)

Silver, Titanium, Graphite, Gold, Platinum- Protected End (cathodic, or most noble)

Galvanic Series of Metals and Alloys

Effects of Galvanic Corrosion

Copper PlateCarbon Steel Bolt

Heavy Corrosion

Heavy Corrosion Aluminum PlateModest Corrosion

Taken from IFI Fastener Standards

CORROSION INFORMATIONCORROSION INFORMATION




298298

General Corrosion Data for Fastener FinishesThere are two popular tests use on fasteners to compare their resistance to corrosion. These test are conduced using procedures that allow a specifier to compare various finishes and materials in a controlled environment. The results do not relate to years of service. Here is an explanation of the tests.

Salt Spray (ASTM B117)

This test is used to compare performance of various finishes in a salt environment. This testing is conducted using a cabinet with a controlled environment consisting of fog with 5% salt solution at 95 degrees F. The test runs continuously with the specimens being visually judged every 24 hours for percent of total surface loss due to red rust along with the number of hours that have accumulated to that point.

Example of Salt Spray Test Cabinet

Example of Kesternich Cabinet

Kesternich (DIN 50018)

This test is used to compare performance of various finishes in an acidic environment. This testing is conducted using a cabinet with a controlled environment consisting of an injection of 0.2 liters of SO2 gas, moisture to a relative humidity of 100% at a temperature of 400 Centigrade. This atmosphere is held for 8-hours, then the door of the cabinet is opened and ambient air is allowed to circulate through the cabinet for 16 hours. This 24-hour period comprises one full cycle. The test runs continuously with the specimens being visually judged every 24 hours for percent of total surface loss due to red rust along with the number of cycles that have accumulated to that point.

The following information was compiled from known data that compares various fi nishes in a controlled environment. The material set forth herein is for general information only and cannot be construed as a substitute for competent professional advice or service. Any part considering application use of this information does so at their own risk and assumes any and all liability from application or use. Consult a corrosion specialist to determine the best fastener for your condition.

SALT SPRAY Per ASTM B117 (Hours to red rust) Carbon steel and 410 stainless steel materialsCoating Salt Spray.00015” min. (3 um) zinc plate with clear chromate 24hrs.0002” min. (6um) zinc with clear chromate 32hrsPassivated 410 Stainless Steel 48hrs.0003” min. (8 um) zinc plating with clear chromate 48hrs.0003” min. (8 um) zinc plating with yellow dichromate 144hrs.0005” min. (12 um) zinc plating with clear chromate 60hrs.0007” min. (14 um) mechanical zinc with clear chromate 72hrsEpoxy (E-Coat) 400hrsTRI-SEAL™ Long-life coating 1,000hrs

The chart provides general information with regard to corrosion resistance of various plating and coatings. Contact TFC for detailed information.

SALT SPRAY RESULTSSALT SPRAY RESULTS

CORROSION PROTECTION INFORMATIONCORROSION PROTECTION INFORMATION

CORROSION INFORMATIONCORROSION INFORMATIONTESTINGTESTING




Table developed by the Metal Construction Association Members (Rev. MBMA 09.17.10)

Note 1: Cautionary Guideline: This table serves as a guideline for the selection of fasteners used with metal roofing. The performance of compatible fasteners shown in this table matches the expected life of the metal roof or wall cladding materials. However, in highly corrosive environments such as heavy industrial, coastal marine, high airborne pollutants or salt spray, preservative treated lumber or fire-retardant lumber, the compatibility of certain fasteners with metal roofing or wall cladding materials may be affected. In those types of applications, the manufacturers of the fastener and metal panel will have specific and unique recommendations.

In addition, in the event that certain coating barriers are damaged or scratched through to the substrate there is increased potential for premature corrosion. Care should be taken during installation and during routine maintenance of the panels in order to protect the integrity of the coatings used for metal panels.Note 2: Screws should be plated/coated per ASTM F1941Note 3: Nails should be galvanized per ASTM A153Note 4: Not recommended for coastal and heavy industrial environments


Fastener Material

Zinc Plated Steel

Screws2


Screws2



Screws



300 Series

Stainless Steel

400 Series

Stainless Steel

Unpainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesPainted Galvanized Steel Yes4 Yes Yes Yes Yes Yes No Yes YesUnpainted Galvalume Steel No Yes Yes Yes Yes Yes No Yes YesPainted Galvalume Steel Yes4 Yes Yes Yes Yes Yes No Yes4 Yes4


Special Note: Preservative-Treated Lumber ApplicationsACQ, Penta, CA or CBA preservative-treated lumber can be incompatible with certain types of fasteners. In those cases where any type of metal roof or wall cladding materials are being attached to preservative treated lumber, the following fasteners are not compatible: zinc plated screws, zinc-alloy headed screws, stainless capped screws, aluminum, copper and copper alloy. When attaching metal panels to those types of preservative-treated lumber, a moisture barrier should be used between the lumber and the panel material. Metal panel fasteners that are compatible with preservative-treated lumber are stainless steel fasteners, or hot dip galvanized nails manufacturedto ASTM A153 class D or heavier. Other types of fasteners coated with proprietary anti-corrosive technologies are also available for use with preservative-treated lumber. In addition, zinc-plated screws can be used in CCA and MCQ pressure-treated lumber.

FASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CFASTENER COMPATIBILITY FOR METAL ROOFING AND WALL CLADDINGLADDING

To minimize galvanic corrosion, fasteners should be considered based on their material compatibility with the substrates.

Determine the materials being fastened and choose a fastener material that is close in proximity on the chart. The closer together the material are on the chart the less galvanic action will occur.

Metals listed on the top of the chart (anotic) will corrode faster than the metals on the bottom of the chart (cathodic).

Contact a corrosion specialist to determine the best material for your application.

GALVANIC CORROSION - COMPATIBLE METALS CHARTSGALVANIC CORROSION - COMPATIBLE METALS CHARTS

CORROSION INFORMATIONCORROSION INFORMATIONGALVANIC ACTIONGALVANIC ACTION




300300

Plating, Coating For Use On Degree of or Finish Corrosion Resistance Characteristics Rust inhibitors All metals Varies with type Oils, greases, etc. Vary in color and film thickness. Usually applied to black oxi de finishes. Used to protect parts in transit and temporary storage.

Zinc, electroplated All metals Very good Blue to blue-white gray color.

Cadmium, electroplated Most metals Excellent Bright silver-gray, dull gray, or black finish. Particularly effective corrosion protection in marine applications. Used for decorative purposes. High lubricity .

Clear chromate finish Zinc and cadmium Very good to excellent Clear bright or iridescent chemical conversion coating applied t o plated parts to enhance plated parts corrosion protection, coloring, and paint bonding.

Dichromate Zinc and cadmium Very good to excellent Yellow, brown, green or iridescent colored coating same as clear chromate. plated parts

Color chromate finish Zinc and cadmium Very good to excellent Olive drab, blue, gold, bronze, etc. Same as clear chromate. plated parts

Zinc or Manganese Steel Good Black in color. Added protection when oiled with a non-drying petroleum oil containing Phosphate corrosion inhibitors. Good lubricity.

Color phosphate coatings Steel Superior to regular phosphate Chemically produced color coating. Available in blue, green, red, purple, etc. and oiled surfaces

Hot-dip zinc All metals Very good Gives maximum corrosion protection. Dull grayish color Necessitates thread size adjustments to permit assembly.

Hot-dip aluminum Steel Very good Gives maximum corrosion protection. Dull grayish color . Necessitates thread size adjustments to permit assemblably.

Mechanically deposited Zinc Steel Very good Dull gray, smooth finish. Corrosion protection depends on coating thickness. Good coverage in recesses and thread roots.

Tin, electroplated All metals Silver-gray color. Excellent corrosion protection for parts in contact with food.

Hot-dip tin All metals Excellent Same as electroplated but thickness is harder to control.

Lead-tin Steel, usually Fair to good Silver-gray, dull coating. Applied by hot-dip method. Helps lubricity.

Silver, electroplated All metals Excellent Decorative, expensive, excellent electrical conductor.

Chromium, electroplated Most metals Good (improves with copper Bright, blue-white, lustrous finish. Has relatively hard surfac e. and nickel undercoats) Used for decorative purposes or to add wear resistance.

Copper, electroplated Most metals Fair Used for nickel and chromium plate undercoat. Can be blackened and relieved to obtain Antique, Statuary, and Venetian finishes.

Brass, electroplated, lacquered Steel, usually Fair Brass electroplated which is then lacquered. Recommended only for indoor decorative use.

Bronze, electroplated, lacquered Steel, usually Fair Has color similar to 80% copper, 20% zinc alloy. Electroplated and then lacquered. Recommended only for indoor decorative use.

Copper, brass, bronze, Most metals Indoor, very good Decorative finishes. Applied to copper, brass,and bronze plated parts to match colors. miscellaneous finishes Color and tone vary from black to almost the original color . Finish names are: Antique, Black Oxide, Statuary ,Old English, Venetian, Copper Oxidized.

Bright nickel Most metals Indoor excellent. Outdoor good Electroplated silver-colored finish. Used for appliances, hardware, e tc. if thickness at least 0.0005 in.

Dull nickel Most metals Same as bright nickel Whitish cast. Can be obtained by mechanical surface finishing or a special satin bath.

Lacquering, clear or All metals Improves corrosion resistance. Used for decorative finishes. Clear or colored to color-matched Some types designed for humid match mating color or luster or other severe applications

Anodizing Aluminum Excellent Acid electrolytic treatment. Frosty-etched appearance. Hard oxide surface gives excellent protection.

Passivating Stainless steel Excellent Chemical treatment. Removes iron particles and produces a passive surface.

Characteristics of Platings, Coatings and Finishes

CORROSION INFORMATIONCORROSION INFORMATIONPLATINGS & APPLICATIONSPLATINGS & APPLICATIONS




“TFC SPECIFIC” FASTENERS FOR USE IN ACQ TREATED LUMBERAND FIRE RATED LUMBEREffective January 1, 2004, lumber treated with arsenic (CCA – Chromated Copper Arsenic) is no longer produced for residential applications, and a new treated lumber material known as ACQ (Alkaline Copper Quanternary) is being utilized.

From a fastener standpoint, it’s important to know that ACQ has up to six (6) times more copper content than the wood it replaces. This condition can cause fasteners plated with electro-plated zinc to corrode at a very fast rate, leaving the bare steel to red rust.

As recommended by the Southern Pine Council (SPC); recognized by the NRCA and the MCA; required by the International Residential Code (R319.3) and the International Building Code (2304.9.5), the following fasteners are acceptable for use in ACQ pressure treated lumber and fi re rated lumber;

• Hot-dipped galvanized complying with ASTM A153,• or coated with proprietary anti-corrosion coatings.• For maximum corrosion protection, fasteners made from 302, 304, 305 or 316 stainless steel (18-8)

should be considered.

Below is a list of TFC brand fasteners that is acceptable for use in ACQ treated lumber or Fire Rated lumber.

1. BLAZER® Drill Screws for wood-to-metal applications coated with TRI-SEAL™ long-life ceramic topcoat.

2. CONCEALOR® Low Profi le Pancake head screws coated with TRI-SEAL™ or TRI-ACQ™ long-life ceramic topcoat.

3. CONCEALOR® ULP Ultra Low Profi le head screws coated with TRI-SEAL™ or TRI-ACQ™ long-life ceramic topcoat.

4. CONCEALOR® DP1 Low Profi le Pancake head screws coated with epoxy coated (E-coat)long-life topcoat.NOTE: Approved for the attachment of treated wood to metal or concrete. Approved for the attachment of a prepunch roof clip to treated wood. Not approved for the attachment of metal panel, trim or siding to treated wood where the screw must penetrate the steel.

5. PANEL-TITE® Post Frame metal-to-wood screws coated with TRI-SEAL™ or TRI-ACQ™ long-life ceramic topcoat.

6. PANEL-TITE® SS Post Frame metal-to-wood screws made of 305 stainless steel.7. SENTRY PLUS FIVE® Roofi ng Fasteners coated with an electro-coated epoxy

(E-coat) topcoat.NOTE: Approved for the attachment of treated wood to metal or concrete. Approved for the attachment of a prepunch roof clip to treated wood. Not approved for the attachment of metal panel, trim or siding to treated wood where the screw must penetrate the steel.

8. TRACER® Drywall screws coated with TRI-SEAL™ or TRI-ACQ™ long-life ceramic topcoat.9. TRI-SEAL™ Long-life coated screws.10. Any fastener made from 300 series stainless steel.11. Any fastener made from 410 stainless steel

Note: Estimating service life of fasteners in ACQ treated lumber cannot be determined due to variables uncontrollable by TFC. Stainless steel screws are recommended. It is important that if carbon steel fasteners are used, they are at the least coated with a fi nish that provides protection equal to or better than hot dipped galvanized like the ones listed above. Determining the proper fastener is the responsibility of the user or specifi er, who assumes all risks and liabilities.

Date: 6.1.10

FASTENERS FOR FASTENERS FOR ACQ TREATED LUMBER ACQ TREATED LUMBER




302302

Stainless Steel MaterialStainless steels are alloys of iron that has a minimum of about 12% chromium. The chromium is the alloying element that imparts its corrosion resistant qualities. It combines with oxygen to form a thin, invisible, non-reactive chromium oxide film on the surface. This self-forming, self-healing passive film always forms in the presents of oxygen. When exposed to weather, a 12% chromium stainless steel (passive) will not corrode (red rust). If greater corrosion protection is required, a stainless grade is used that has mores chromium.

300 Series stainless steels are chromium-nickel compositions and are known as austenitic. They offer excellent corrosion resistance, for the most part are non-magnetic, and have excellent ductility. 300 series stainless steel can be cold work hardened and show slight magnetism, but it cannot be heat-treated. Type 304 is one of the most popular for fasteners used in construction applications. This type, sometimes referred as 18-8 (18% chromium, 8% nickel), provides better thread strength than 302, helping eliminate thread rollover. Most fasteners that are made in 304 stainless are self-tapping type due to the fact that they cannot be heat-treated. Self-drilling fasteners are available, but for steel applications must have a carbon steel drill tip affixed to the body so drilling can occur like our SD300 brand.

400 Series stainless steels are straight-chromium compositions and are known as martensitic. They resist corrosion in mild environments, and can be heat-treated for additional strength. They are magnetic, and when heat-treated, provide exceptional strength. The most popular grade used for fasteners is 410 stainless. Because of its heat-treating capabilities, self-drilling fasteners are widely produced in this grade. Corrosion can occur rather quickly if not properly process. It is recommended that fasteners that are used in exterior construction applications have some sort of plating on the surface. This will not only aid improve corrosion resistance, but can provide lubricity for improving drilling and tapping.

Material SelectionMany variables characterize a corrosive environment, i.e., chemicals and their concentration, atmospheric conditions, temperature, time, so it is difficult to select which alloy to use without knowing the exact nature of the environment. However, there are guidelines:

Type 304 serves a wide range of applications. It withstands ordinary rusting in architecture, it is resistant to food-processing environments (except possibly for high-temperature conditions involving high acid and chloride contents), it resists organic chemicals, dyestuffs, and a wide variety of inorganic chemicals. Type 304 L (low carbon) resists nitric acid well and sulfuric acids at moderate temperature and concentrations. It is used extensively for storage of liquefied gases, equipment for use at cryogenic temperatures (304N), appliances and other consumer products, kitchen equipment, hospital equipment, transportation, and wastewater treatment.

Type 316 contains slightly more nickel than Type 304, and 2-3% molybdenum giving it better resistance to corrosion than Type 304, especially in chloride environments that tend to cause pitting. Type 316 was developed for use in sulfite pulp mills because it resists sulfuric acid compounds. Its use has been broadened, however; to handling many chemicals in the process industries.

Type 430 has lower alloy content than Type 304 and is used for highly polished trim applications in mild atmospheres. It is also used in nitric acid and food processing.

Type 410 has the lowest alloy content of the three general-purpose stainless steels and is selected for highly stressed parts needing the combination of strength and corrosion resistance, such as fasteners. Type 410 resists corrosion in mild atmospheres, steam, and many mild chemical environments.

Service tests are most reliable in determining optimum material, and ASTM G-4 is a recommended practice for carrying out such tests. Tests should cover conditions both during operation and shut-down. For instance, sulfuric, sulfurous and polythionic acid condensates formed in some processes during shutdowns may be more corrosive than the process stream itself. Tests should be conducted under the worst operating conditions anticipated.

Specifications and recommended practices relating to stainless steels are also issued by ASTM. Stainless steels resist corrosion in a broad range of conditions, but they are not immune to every environment. For example, stainless steels perform poorly in reducing environments, such as 50% sulfuric and hydrochloric acids at elevated temperatures. The corrosive attack experienced is a breakdown of the protective film over the entire metal surface.

Such misapplications of stainless steels are rare and are usually avoided. The types of attack which are more likely to be of concern are pitting, crevice attack, stress corrosion cracking, and intergranular corrosion.

Source: Design Guidelines for the selection and use of stainless steel. Specialty Steel Industry of the United States.

STAINLESS STEELSTAINLESS STEELTECHNICAL DATATECHNICAL DATA

Relative Corrosion Resistance of AISI Stainless Steels Atmospheric Chemical TYPE UNS Mild Atmospheric Number Number and Fresh Water Industrial Marine Mild Oxidizing Reducing

302 (S30200) X X X X X 304 (S30400) X X X X X 305 (530500) X X X X X 316 (531600) X X X X X X 410 (S41000) X X 430 (543000) X X X X

* The"X" notations indicate that a specific stainless steel type may be considered as resistant to the corrosive environment categories.

This list is suggested as a guideline only and does not suggest or imply a warranty on the pan of the Specialty Steel Industry of the United States or any of the member companies. When selecting a stainless steel for any corrosive environment, it is always best to consult with a corrosion engineer and, if possible, conduct tests in the environment involved under actual operating conditions.




ACIDSHydrochloric acid: Stainless generally is not recommended except when solutions are very dilute and at room temperature.

"Mixed acids": There is usually no appreciable attack on Type 304 or 316 as long as sufficient nitric acid is present.

Nitric acid: Type 304L or 430 is used.

Phosphoric acid: Type 304 is satisfactory for storing cold phosphoric acid up to 85% and for handling concentrations up to 5% in some unit processes of manufacture. Type 316 is more resistant and is generally used for storing and manufacture if the fluorine content is not too high. Type 317 is somewhat more resistant than Type 316. At concentrations up to 85%, the metal temperature should not exceed 212 F (100 C) with Type 316 and slightly higher with Type 317. Oxidizing ions inhibit attack and other inhibitors such as arsenic may be added.

Sulfuric acid: Type 304 can be used at room temperature for concentrations over 80%. Type 316 can be used in contact with sulfuric acid up to 10% at temperatures up to 120 F (50 C) if the solutions are aerated; the attack is greater in airfree solutions. Type 317 may be used at temperatures as high as 150 F (65 C) with up to 5% concentration. The presence of other materials may markedly change the corrosion rate. As little as 500 to 2000 ppm of cupric ions make it possible to use Type 304 in hot solutions of moderate concentration. Other additives may have the opposite effect.

Sulfurous acid: Type 304 may be subject to pitting, particularly if some sulfuric acid is present. Type 316 is usable at moderate concentrations and temperatures.

BASESAmmonium hydroxide, sodium hydroxide, caustic solutions : Steels in the 300 series generally have good corrosion-resistance at virtually all concentrations and temperatures in weak bases, such as ammonium hydroxide. In stronger bases, such as sodium hydroxide, there may be some attack, cracking or etching in more concentrated solutions and at higher temperatures. Commercial purity caustic solutions may contain chlorides, which will accentuate any attack and may cause pitting of Type 316 as well Type 304.

ORGANICSAcetic acid: Acetic acid is seldom pure in chemical plants but generally includes numerous and varied minor constituents. Type 304 is used for a wide variety of equipment including stills, base heaters, holding tanks, heat exchangers, pipelines, valves and pumps for concentrations up to 99% at temperatures up to about 120 F (50 C). Type 304 is also satisfactory for contact with 100% acetic acid vapors, and-if small amounts of turbidity or color pickup can be tolerated for room temperature storage of glacial acetic acid. Types 316 and 317 have the broadest range of usefulness, especially if formic acid is also present or if solutions are unaerated. Type 316 is used for fractionating equipment, for 30 to 99% concentrations where Type 304 cannot be used, for storage vessels, pumps and process equipment handling glacial acetic acid, which would be dis-colored by Type 304. Type 316 is likewise

applicable for parts having temperatures above 120 F (50 C), for dilute vapors and high pressures. Type 317 has somewhat greater corrosion resistance than Type 316 under severely corrosive conditions. None of the stainless steels has adequate corrosion resistance to glacial acetic acid at the boiling temperature or at superheated vapor temperatures.

Aldehydes: Type 304 is generally satisfactory.

Amines: Type 316 is usually preferred to Type 304.

Cellulose acetate: Type 304 is satisfactory for low temperatures, but Type 316 or Type 317 is needed for high temperatures.

Citric, formic and tartaric acids: Type 304 is generally acceptable at moderate temperatures, - but Type 316 is resistant to all concentrations at temperatures up to boiling.

Esters: From the corrosion standpoint, esters are comparable with organic acids.

Fatty acids: Up to about 300 F (150 C), Type 304 is resistant to fats and fatty acids, but Type 316 is needed at 300 to 500 F (150 to 260 C) and Type 317 at higher temperatures.

Paint vehicles: Type 316 may be needed if exact color and lack of contamination are important.

Phthalic anhydride: Type 316 is usually used for reactors, fractionating columns, traps, baffles, caps and piping.

Soaps: Type 304 is used for parts such as spray towers, but Type 316 may be preferred for spray nozzles and flake-drying belts to minimize off color product.

Synthetic detergents: Type 316 is used for preheat, piping, pumps and reactors in catalytic hydrogenation of fatty acids to give salts of sulfonated high molecular alcohols.

Tall oil (pulp and paper industry): Type 304 has only limited usage in tall-oil distillation service. High-rosin-acid streams can be handled by Type 316L with a minimum molybdenum content of 2.75%. Type 316 can also be used in the more corrosive high-fatty-acid streams at temperatures up to 475(245 C), but Type 317 will probably be required at higher temperatures.

Tar: Tar distillation equipment is almost all Type 316 because coal tar has a high chloride content; Type 304 does not have adequate resistance to pitting.

Urea: Type 316L is generally required.

Pharmaceuticals : Type 316 is usually selected for all parts in contact with the product because of its inherent corrosion resistance and greater assurance of product purity.

Where Different Grades of Stainless Steel Are Used

Source: Design Guidelines for the selection and use of stainless steel. Specialty Steel Industry of the United States.

STAINLESS STEELSTAINLESS STEELTECHNICAL DATATECHNICAL DATA




304304

The NEED-IT-NOW!™ program is based around a “trade specifi c” product sheet that quantifi es all the products and services used by a specifi c trade.

This “trade specifi c” product sheet is the key element of the program so you have a clear understanding of what products best meets your requirements.

BENEFITS OF THE NEED-IT-NOW!™ PROGRAM ◄ Provides a fast and easy way to locate products used by a

specifi c trade. ◄ Provides a fast and easy way to locate the details of

a product including technical information by using the Fastening Systems Guide.

◄ Provides a list of trade specifi c products to assist in developing an inventory program to support specifi c needs.

◄ Reminds you of all the items TFC has available for the specifi c trade.

◄ It can be used as an inventory management tool to understand what products are used by a specifi c trade.

◄ Provides pricing details on all items to reduce lead times.

COMMERCIAL DRYWALLCOMMERCIAL DRYWALL

FLAT ROOFINGFLAT ROOFING

METAL BUILDING/ METAL ROOFINGMETAL BUILDING/ METAL ROOFING

Contact any of our branches to fi nd out more about the NEED-IT-NOW!™ program for the following trades.

NEED-IT-NOW!NEED-IT-NOW!TRADE SPECIFIC PRODUCT PROGRAMTRADE SPECIFIC PRODUCT PROGRAM




PAK-ONE PAK-ONE INVENTORY MANAGEMENTINVENTORY MANAGEMENT




306306

TOOL REPAIRTOOL REPAIR

Are your tools in need of repair?Contact our service center and we will have your RAMSET powder actuated or gas charged tool repaired in one week of less!

• Clean - Repair - Test• Full Warranty Repairs• Replacement Parts• Maintenance programs




SELLER’S LIMITED WARRANTY

Triangle Fastener Corporation (“Triangle”) warrants, subject to the terms hereof, that all goods sold hereunder will be free from defects in material and workmanship.

THE ABOVE-STATED LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, OR ANY OTHER WARRANTY, WHETHER EXPRESSED OR IMPLIED. ALL OTHER WARRANTIES ARE HEREBY DISCLAIMED.

The remedies set forth below with respect to any breach of this warranty are exclusive and in lieu of all other liabilities and obligations on Triangle’s part with respect to the quality of the goods sold by Triangle.

Triangle’s sole obligation for breach of this warranty shall be to issue credit to the buyer equal to the price paid for the defective goods or to replace the defective goods. The decision with respect to whether credit should be issued or whether the goods should be replaced shall be in Triangle’s sole discretion.

If goods are claimed to be other than as warranted, Triangle, upon notice promptly given, will either examine the goods at their site or issue shipping instructions for return to Triangle (transportation costs prepaid by buyer). If any goods are proven to be other than as warranted, transportation costs to and from Triangle’s plant will be borne by Triangle and reimbursement or credit will be made for reasonable costs so expended by buyer. In no event shall Triangle be responsible for the cost of removing or replacing any goods from or in their installations.

IN NO EVENT WILL TRIANGLE BE LIABLE TO BUYER FOR INDIRECT, INCIDENTAL, EXEMPLARY, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES RELATING TO LOSS OF PROFITS, INCOME, OR GOODWILL) ARISING OUT OF ANY DEFECT IN THE GOODS, WITHOUT REGARD TO THE LEGAL THEORY OF SUCH DAMAGES, WHETHER SUCH DAMAGES ARE BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, INDEMNITY, NEGLIGENCE, GROSS NEGLIGENCE, STRICT LIABILITY OR OTHERWISE.

The goods shall be deemed to be accepted and any claim for breach of the warranty made herein shall be deemed to be waived by buyer unless buyer notifies Triangle in writing of its claim within six (6) months from date of shipment of the goods, time being of the essence.

This limited warranty shall not extend to any goods which have been subjected to misuse or neglect, damaged by accident or rendered defective by reason of improper handling or installation. Triangle does not accept any liability for fair wear and tear, or for charges for repairs or replacements made without authority or contingent liability of any kind.

The above terms shall not be amended or modified in any way, unless in a writing signed by a principal officer of Triangle.

WARRANTYWARRANTY

tfc guide_full catalog

Documents