technical specification sandvik dl421-7 7-6347-a ... · pdf filesandvik dl421-7 underground...
TRANSCRIPT
Technical Specification7-6347-A2011-06-30
Sandvik DL421-7Underground Drill Rig
1/4
© 2
011
San
dvik
Min
ing
and
Co
nst
ruct
ion
The Sandvik DL421-7 is an electro-hydraulic long-hole drilling rig for large-scale production drilling inunderground mines.
The rig has been designed for vertical and inclinedplane rings and fans, parallel long production holesas well as long single holes. The 360° rotation andparallel coverage, together with wide tilt angleranges forwards and backwards, make the boomsuitable to various drilling applications.
Instrumentation and data drilling with various auto-mation options allow maximum performance withsuperior drilling accuracy. Proven CAN-based tech-nology on board allows the operator to set the unitfor any rock conditions. It also makes the upgrade ofautomation level easy, and has a fault finding sys-tem, which reduces downtime.
The machine is based on a proven carrier for highmobility. Both drilling and tramming are done fromthe operator's platform.
Carrier NC7W
Rock drill HL710
Boom ZR30
Drilling module LFRC1600
Control system TPC LH
Hole diameter 89-102 mm
Drilling hole length Up to 54 m
Cornering 3950 mm
Total weight22 000 kg(depending on options)
Technical Specification
Sandvik DL421-77-6347-A
2011-06-30
2/4
Coverage area
22902070
2050
3000
650
1030
H
HR
W
WP 2000Optional
front stinger
MINIMUM DRIFT SIZE
MAXIMUM DRIFT SIZE
Drilling Module
H W WF HR
LF1604 3245 3245 1450 2100LF1605 3550 3550 1750 2100LF1606 3855 3855 2050 2100
Included 100mm clearance on each side
Drilling Module
H W WF HR
LF1604 4150 4700 3000 2100LF1605 4250 4900 3000 2100LF1606 4370 5100 3000 2100
With rear stinger in use without optional front stinger
All dimensions in mm
Rock Drill HL710Percussion power 19.5 kWPercussion pressure 190 bar maxPercussion rate 42-52 HzRotation speed 0...180 rpm (OMT315)Rotation torque Max. 1765 Nm (OMT315)Hole size 89 - 102 mm
Recommended drill steel38-51 mm rods64 mm tubes
Shank adaptor T38, T45, T51Weight Max. 245 kgFlushing water pressure Max. 20 bar*Power extractor HL710
Hydraulic rock drill Technical Specification 2_1750
Boom type ZR30Parallel coverage 3000mm
Feed extensionLF1604: 1000mmLF1605: 1100mmLF1606: 1400mm
Rotation angle 360°Weight 2 800kg
Stinger extensionLF1604: 1500mmLF1605/6: 1700mm
Boom Technical Specification 4_1810
LFRC160x x=4’ / 5’ /6’Capacity 29+1 rods/tubesFeed force 31kNRod retainer Pito 16Cuttings collector CC1016*Sequence control Automatic rod/tube changing*Front stinger Required for downholes*Readiness for double tools Rods/Tubes
Drilling module
*TMS DDSDrilling direction, depth andspeed
*Data transfer USB/LAN/WLAN*Tele-remote drilling LAN/WLAN*Data transfer with teleremote drilling
LAN/WLAN
*Uphole fan automation*One hole data drilling Automated single hole drilling
*Instrumentation options Technical Specification 5_9201
*Pressure cleaning system with reel
5-15 bar
*High pressure cleaning system with reel
Max. 180 bar
*Cleaning system
*Pressure cleaning system with reel
5-15 bar
*High pressure cleaning system with reel
Max. 180 bar
*Cleaning system
*Manual fire suppression system
6 nozzles
*Automatic fire suppression system
6 nozzles
*FS1000 above 0°C*Hand held fire extinguisher Operator station
*Fire suppression system and options
*Optional features/components
Technical Specification
Sandvik DL421-77-6347-A
2011-06-30
3/4
Machine dimensions
17652100
360°
22°
30° 22°
53°
490195
3280 3530
11100
1425 834 1400
2442
3300 (LF1604)3600 (LF1605)3900 (LF1606)
All dimensions in mm
Filtration size20 microns (pressure)12 microns (return)
Oil coolerCooling capacity 45kWOW45 water cooling
Drilling oil tank 230 litersTank filling Electric filling pumpPowerpack HPP755 (55kW)Percussion pump 100cc variable displacementRotation pump 45cc variable displacementBoom movements pump 28cc variable displacement*Biodegradable oils Shell Naturelle HFE68
Hydraulic system
Type TPC LH5
Power controlAdjustable full powerAdjustable collaring power
Anti-jamming controlAdjustable anti-jamming pressure
Rotation control Adjustable rotation speed
Flushing controlWater flushing flow and pressure control
*Double control system Cable remote control panel
Control system
Total input power 80 kWMain switch MSE 10Standard voltages 380-690 VACStarting method Direct on lineVoltage fluctuation ±10%Cable reel TRC3ER with spoolingCable reel control Control at operator station *Star delta starter Standard for 480V and lower*Optional voltage 1000 VAC
*Electric cable rubber or PUR100m, 150m or 200mdepending on voltage
*Ground fault and over current unit
VYK
*Auxiliary outlet 230V, 16A*Remote control for reel(s) At rear end*Three phase network oulet voltage
Readiness only
*Battery jump start
Electric system
Flushing WaterWater pump WBP 2 (50Hz 7,5 kW)Water pump capacity 200 l/min (Max. 12bar)Inlet pressure 2-7 bar (while drilling)Shank lubrication Air/oil mist, SLUAir consumption 300-450l/minOil consumption 250-400g/minShank lubrication compressor CT10, 1.0m3/min (7bar)Air cleaner IP5
*CompressorCT16 (11kW, 1.6m3/min) or CT28 (18.5kW, 2.8m3/min)
*Water hose 32mm (1¼”)38mm (1½”)
100 meters65 meters
*Air mist flushing packages External water/air connection
Flushing system and shank lubrication
*Optional features/components
Technical Specification
Sandvik DL421-77-6347-A
2011-06-30
4/4Sandvik Mining and Construction OyP.O Box 100. FIN-33311 Tampere, FinlandTel. +358 205 44 121, Fax +358 205 44 120www.sandvik.com
Sandvik Mining and Construction reserves the right to change this specification without further notice.
© 2
011
San
dvik
Min
ing
and
Co
nst
ruct
ion
Tramming dimensions
H
11°
1125035303280
1425
45016°
195
34202680
3100
3950B
3950R1
R2
40°750
750
B
3550
6800
w
FEED W B R1 R2
LF1604 3300 4100 6800 3350
LF1605 3600 4300 6900 3150
LF1606 3900 4500 7000 3050
All dimensions in mm
Tramming speed15 km/h on horizontal14% = 1:7 = 8° 6,5km/h
Gradeability / Inclination Max. 15° / 5°
Tramming
Safety canopy FOPS (ISO 3449)Controls Drilling and trammingFront screen protection bar StandardSound pressure level according to EN791
Operator station: 102 dB(A)Emitted: 127 dB(A)
SeatErgonomic, adjustable with seat belt
Operator’s station
Front lights(combined working and driving)
6 x 35W HID (24V)
Rear working lights 2 x 35W HID (24V)Rear driving lights 2 x 35W HID (24V)Rear brake lights 2 x Red LEDAmber flashing light StandardPositioning lights 2 x Laser type*Extra working lights 2 x 35W HID (24V)
Lights
*Harsh water options (level 1) Oil cooler + boom cylinders
*Harsh water options (level 2)Level 1 + steering and jacks cylinders
*Regional AUS, USC, EUR
*Packages
Spare wheel assembly Air filledSpare wheel assembly Foam filledSpare rock drillSpecial tools for rock drill
Extra documentationPaper copiesToolman/Catbase/Link one
Extra items
Carrier name NC7WCarrier type Wheel mounted, frame steering
TransmissionHydrodynamicSpicer T20 000
Axles SpicerTyres 14.00-24Diesel engine MB904LA (110kW) Tier IIIExhaust catalyser+muffler Standard
Brakes
Service, hydraulic wet disc brakes Parking and emergency SAHR type, fail safewet disc brakes
Ground clearance 450 mmRear oscillation ± 10°Articulation ± 40°Steering Frame steeringFuel tank 150 liters
Hydraulic jacksFront frame stabilizerTJ60 (rear)
Stair and service lights LEDHand throttle StandardReverse alarm Standard*Reversing cameras On machine rear and side*Third gear lockout*Automatic water hose reel THR2.5E*Wheel chocks 2 pieces*Fast filling systems For fuel/complete*Sealed gel batteries*Foam filled tyres
Carrier
*Optional features/components