tec 4607 wind and hydro power technologies fall 2011
TRANSCRIPT
![Page 1: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/1.jpg)
Hydro System DesignDynamic Head, Power Output, Penstock and Nozzle
Selection
TEC 4607 Wind and Hydro Power TechnologiesFall 2011
![Page 2: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/2.jpg)
Section OutlineCalculate gross / static output
Determine site head, flow, penstock, design flow
Utilize head and flow to choose penstock material and pipe diameter
Calculate net / dynamic output
Choose system nozzles
Choose a system turbine
![Page 3: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/3.jpg)
Calculate gross / static output
Power output (watts) = Flow (GPM) X Static Head (ft)
8 – 12 Example: A site assessment showed the following:140 feet of static head100 gpm (of usable flow) Power output (watts) = Flow (gpm) X Static Head (ft) 8 – 12 PO = 100 X 140
10PO = 1400 watts or 1.4 kW
NOTE: This system will not achieve this output. WHY?
System Efficiency
![Page 4: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/4.jpg)
Designed System Flow and OutputDesigned Flow = Amount of Flow you have to work with.
The sites flow can fluctuate during the year!You can design around these constraints: You have Options!Option #1
Determine the low or most constant flow and design a system around this flow.
Option #2Determine high and low median flows and design a system
that can adapt to these conditions. This may take more site assessment throughout the year and
ultimately cost more, but could save more in the end. More on how to do this a little later!
![Page 5: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/5.jpg)
Choosing your Penstock
Factors to determine: Volume of WaterMaterialDiameter of PipeLength of Pipe Changes in Direction
![Page 6: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/6.jpg)
Other Penstock Design Considerations
Reduce AirReduce Turbulence by:
Keep penstocks as straight as possible!
Steady elevation declines
Standpipe Vent
![Page 7: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/7.jpg)
Steady elevation declinesKeep the declines as
consistent as possible.If you form high spots,
include a bleeder valve.
Home Power 125
![Page 8: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/8.jpg)
Keep them straight and constant (as possible)
Both the penstock and the manifold!
![Page 9: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/9.jpg)
Avoid sudden enlargements!
![Page 10: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/10.jpg)
Solution: Gradual Enlargements!
7 degree angle of enlargement is optimal for most fittings!
![Page 11: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/11.jpg)
Avoid sudden constrictions!
![Page 12: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/12.jpg)
Solution: Gradual Constrictions!
Source: westerndynamics. Com for all pipe images.
![Page 13: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/13.jpg)
Step 1:After you have determine static head, flow, and penstock length
Determine allowable penstock losses:System losses should be between 5% and 20%
This is for financial reasons. Larger pipe costs more and is often not worth the investment for small efficiency gains.
Remember: larger pipe has less friction loss!
All determined based on cost of pipe and achievable outputs
Larger diameter pipe costs more – you may want a lower efficiency to save on installation cost.
![Page 14: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/14.jpg)
Step 2:Determine a high and low friction loss
Lets use an example site: Assume the following:Turtle Island Preserve140 ft static head300 GPM max stream flow200 GPM min stream flow Design flow of 100 GPM?1300’ penstockWhat size PVC pipe will be best?
![Page 15: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/15.jpg)
Step 2:Determine a high and low friction loss
Efficiency loss of 5% (low loss): Total Static Head: 140 feet
140 feet X .05 = 7 feet 140 static head – 7 feet of total loss = 133 feet dynamic
head Efficiency loss of 20% (high loss):Total Static Head: 140 feet 140 feet X .20 = 28 feet 140 static head – 28 feet of loss = 112 feet of dynamic head
![Page 16: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/16.jpg)
Step 3:Determine Pipe Diameter
1. Use the Penstock chart to determine friction losses / 100 feet of pipe.
2. Look-up your designed flow on the left column3. Compare it to different diameter pipes.4. Convert PSI to feet (if necessary) PSI X 2.31 = feet of head5. Multiply by # of 100 foot lengths
![Page 17: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/17.jpg)
Step 3 Cont.:Determine Pipe Diameter
1. Use the Penstock chart to determine friction losses / 100 feet of pipe.
2. Look-up your designed flow on the left column (100 GPM)3. Total loss is 6.29 (2 in.) 0.92 (3 in.)4. Convert 0.92 psi to feet 0.92 X 2.31 = 2.12 feet 5. Multiply by # of 100 foot lengths 2.12 feet X 13 (100 foot lengths) =
= 27.56 feet of total head loss Will this work? – Yes but not ideal – go bigger!
![Page 18: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/18.jpg)
Step 3 Cont.:Determine Pipe Diameter
1. Use the Penstock chart to determine friction losses / 100 feet of pipe.
2. Look-up your designed flow on the left column (100 GPM)3. Total loss of 4 inch pipe (on chart) = 0.25 psi or 0.578 feet 5. Multiply by # of 100 foot lengths 0.578 feet X 13 (100 foot lengths) = 7.51 feet of total head lossWill this work? Yes – just over 5% loss
![Page 19: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/19.jpg)
Step 4: Determine Friction losses in fittingsRefer to friction loss tables for fittings,
valves, and bends.Use the “Equivalaent length of feet” charts
for easy calculations. 1. Determine number of fittings of each
type.2. Find the total equivalent length of feet of
pipe 3. Determine friction loss of for # of feet for
each material. 4. Add to total losses in head calculations.
![Page 20: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/20.jpg)
Step 5: Calculate Dynamic / Net Head
Subtract the total loss of head for length of pipe based on the chart from the static head measurement.
Our example: 140 feet of total static head7.51 feet of total head loss (NOT including
fittings)140 feet of static head – 7.51 feet of total loss
= 132.49 feet of Dynamic / Net Head!
![Page 21: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/21.jpg)
Step 6: Determine Nozzle Size
Use the chart from the manufacturer to determine number and size of nozzles for the turbine.
Step 1: Find Dynamic/Net head on the left column.
Step 2: Find a combination of nozzles that will provide the amount of flow you have.
Remember: For most hydro systems, a 0.5 inch nozzel is the limit for a Pelton Wheel
![Page 22: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/22.jpg)
Step 5: Determine Nozzle Size
![Page 23: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/23.jpg)
![Page 24: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/24.jpg)
Step 5: Determine Nozzle Size
Based on the chart:
2 7/16” nozzles and 1 1/4” nozzles will work.
Total Flow from the nozzles=95.8 gallons / minute.
But it will be higher based on the chart not showing 132 feet of head!
![Page 25: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/25.jpg)
Step 6:Calculate total Net Output
Power output (watts) = Flow (GPM) X Net Head (ft)
8 – 12
Power output (watts) = Flow (GPM) X Net Head (ft) 8 – 12 PO = 95.8 gallons X 132.49 feet of
net head 10
PO = 1,269 watts or 1.269 kW
System Efficiency
![Page 26: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/26.jpg)
Step 7:Daily, Monthly and Yearly Energy Output
Daily Output:Power Output X 24 hours / day = 1.3 kW X 24 hours =
31.2 kWh /day
Monthly Output:Power Output X 720 hours / month = 1.3 kW X 24 hours =
936 kWh / month
Yearly Output (AEO):Power Output X 8760 hours / year = 1.3 kW X 8760 hours =
11,388 kWh / yearWill this power an average American home?What does this calculation NOT account for?
![Page 27: TEC 4607 Wind and Hydro Power Technologies Fall 2011](https://reader036.vdocuments.mx/reader036/viewer/2022062718/56649e705503460f94b6e386/html5/thumbnails/27.jpg)
Step 7 Continued:Daily, Monthly and Yearly Energy Output
Yes, this system could power the average American Home!
The average U.S. Household uses between 10,000 – 12,000 kWh/year
This calculation does not include system maintenance, energy storage, freezing, and repairs.