subsea exercise no.5
DESCRIPTION
Completed Kill Sheet for SubseaTRANSCRIPT
Revised April 2012 1
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5
API (Field) Units ™
SUBSEA KILL SHEET EXERCISE No. 5
Name: ______________________________________ Date: ___________________ Complete the Subsea vertical kill sheet provided on pages 2 and 3. Then answer questions 1 to 12. Please round calculations as per good well control practice.
Well data :
Hole size 8 ½ inches Hole depth (Below RKB) 6,080 feet MD, 6040 ft TVD Casing shoe depth 9
5/8 inches, 5000 ft MD/TVD
RKB to mean sea level (MSL) 50 feet
Internal capacities: Drill pipe 5 inch (S-135-NC50), capacity 0.0178 bbl/ft Heavy wall drill pipe 5 inch, length 400 ft, capacity 0.0088 bbl/ft Drill collars 6 ½ inch x 2
13/16inch, length 600 ft, capacity 0.0077bbls/ft
Choke line 3 inch ID, length 515 ft, capacity 0.0087 bbls/ft Marine riser length 500 feet, capacity 0.3892 bbls/ft
Annulus capacities: Drill collars in open hole 0.0292 bbl/ft Drill pipe and HWDP in open hole 0.0459 bbl/ft Drill pipe and HWDP in casing 0.0505 bbl/ft Drill pipe in Marine riser 0.3638 bbl/ft
Mud pump data: Pump output at 98% volumetric efficiency 0.102 bbl/stroke
Slow circulation rate data: @ 45 spm through the riser 400 psi @ 45 spm through the choke line 500 psi
Other relevant information: Active surface fluid volume 460 bbl Drill pipe, 5 inch closed end displacement 0.0254 bbl/ft Seawater density 8.6 ppg Surface line volume 14 bbls
Formation strength test data: Surface leak-off pressure with 10.0 ppg mud 1500 psi
Kick Data: The well kicked at 6040 vertical depth
Shut in drill pipe pressure 600 psi Shut in Casing pressure 870 psi Recorded pit gain 19 bbls Mud weight in hole 10.4 ppg
The well will be killed using the Wait and Weight method
Answer the following TWELVE questions from the data above. The attached kill sheet may be used to assist you with your calculations
Revised April 2012 3
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5
API (Field) Units ™
Revised April 2012 4
IWCF Drilling Well Control Subsea Kill Sheet Exercise No.5
API (Field) Units
™
1. Calculate the pressure safety margin at the casing shoe in this static condition,
assuming the top of the kick is below the casing shoe. Answer____________ psi
4 points
2. How many strokes are required to pump from pump to bit?
Answer____________ strokes
4 points
3. How many strokes are required to pump from the bit to casing shoe?
Answer____________ strokes
4 points
4. How much time is required to circulate the total well system volume?
Answer____________ minutes
4 points
5. How many strokes are required to displace the marine riser to kill fluid before opening the BOP?
Answer____________ strokes
4 points
6. What is the kill mud density? Answer____________ ppg
4 points
7. What is the Initial Circulating Pressure? Answer____________ psi
4 points
8. What is the Final Circulating Pressure? Answer____________ psi
4 points
Revised April 2012 5
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5
API (Field) Units ™
9. What is the Initial dynamic casing pressure at kill pump rate? Answer____________ psi
4 points
10. What is the MAASP after circulation of the kill mud? Answer____________ psi
4 points
11. Calculate the pressure drop per 100 strokes of kill mud fluid pumped inside the drill string.
Answer____________ psi/100 strokes
4 points
12. If all the influx is at the bottom of the hole, calculate the gradient of the influx. Answer____________ psi/ft
4 points
Revised April 2012 6
IWCF Drilling Well Control Subsea Kill Sheet Exercise No.5
API (Field) Units
™
SUBSEA KILL SHEET EXERCISE NO. 5
Answers
Before attempting to fill in the kill sheet, draw a simple sketch of the well to determine the total
annulus lengths. An example is shown below. Only use measured depths and remember that
total annulus length (including the choke line) may not equal measured depth if the Choke line
length is greater than the Riser length.
Revised April 2012 7
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 8
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 9
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 10
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 11
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 12
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
SUBSEA KILL SHEET EXERCISE NO. 5
Answers 1. 508 psi
Pressure Safety Margin = MAASP – SICP
= 1378 psi – 870 psi
= 508 psi
2. 1104 strokes
From Kill Sheet, surface to bit strokes = 967 stokes
Surface line strokes = 14 bbls ÷ 0.102 bbl/stroke = 137 strokes
Pump to Bit stokes = 967 + 137 = 1104 strokes
3. 388 strokes
4. 80 - 81 minutes (80.6 minutes)
5. 1782 - 1786 strokes (1784 strokes)
6. 12.4 ppg
7. 1000 psi
8. 477 psi
9. 770 psi
10. 858 psi
New MAASP = (Max. Allowable Mud Density – Kill Mud Density) x 0.052 x TVDshoe
= (15.7 ppg – 12.4 ppg) x 0.052 x 5000 ft.
= 858 psi
11. 54 psi/100 strokes
= 239.2 feet
Revised April 2012 13
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
12. Volume of Influx around Drill Collars = DC/OH annular capacity(bbls/ft) x DC Collar length
= 0.0292 bbls/ft x 600 feet
= 17.52 bbls
Voulme of Influx around HWDP = Kick Volume - 17.52 bbls
= 19 bbls – 17.52 bbls
= 1.48 bbls
Height of Influx above Drill Collars = 1.48 bbls ÷ HWDP/OH annular capacity (bbls/ft)
= 19 bbls ÷ 0.0459 bbls/ft
= 32.2 feet
Total Influx height = 600 + 32.2 feet = 632.2 feet
Formation Pressure = SIDDP + HP string
= 600 + (10.4 ppg x 0.052 x 6040 ft)
= 600 psi + 3266.4 psi
= 3866.4 psi
HSP mud in annulus = 10.4 ppg x 0.052 x (6040 ft -632.2 ft)
= 10.4 ppg x 0.052 x 5407.8 ft.
= 2924.5 psi
Kick Hydrostatic = Formation Pressure – SICP – HSP mud in annulus
= 3866.4 psi – 870 psi – 2924.5 psi
= 71.9 psi
Gradient of Influx = Kick Hydrostatic (psi) ÷ Height of Influx (ft)
(psi/ft) = 71.9 psi ÷ 632.2 feet
= 0.113 psi/ft
Revised April 2012 14
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™
Revised April 2012 15
IWCF Drilling Well Control Subsea Kill Sheet Exercise No. 5 - Answers
API (Field) Units
™