stacking hub 10.3 quick start guide hub 10 · identified by mate3 on power-up: 3-phase/split...

#10 x ½” Screws x 2

Quick Start Guide

900-0154-01-00 Rev A.vsd\2013-03-13©2013 OutBack Power Technologies. All Rights Reserved.

HUB 10.3

HUB10.3 HUB Wiring CoverCable, CAT5e, 3' (1 m) x 2Cable, CAT5e, 6' (2 m) x 3

Parts List

Cable, CAT5e, 10' (3 m) x 4

Contact Technical Support:Telephone: +1.360.618.4363Email: [email protected]: www.outbackpower.com

IMPORTANT: Not intended for use with life support equipment.

OutBack Power, the OutBack Power Logo, and FLEXgrid are trademarks owned and used by OutBack Power Technologies, Inc. The ALPHA logo and the phrase “member of the Alpha Group” are trademarks owned and used by Alpha Technologies. These trademarks may be registered in the United States and other countries.

Stacking HUB 10.3


Jumper position identified by MATE3 on power-up:

3-Phase/Split Single-Phase

3.

Changing Jumpers1. 2.

Used for classic series, OutBack series, and parallel stacking. This is the factory-installed initial position.

Used for Subphase Master stacking (both three-phase and series configurations).

4a.Single-phase(all jumpers)

4b.3-Phase/Split(all jumpers)

3.

2.

1.

1" recommended

Mounting

NOTE: This option requires MATE3 firmware revision 002.013.000 or higher.

Master A

Master C SlaveSlave

Slave Slave

or

X1st MATE

12

3

45

6

78

9

10

Three-Phase Stack (Subphase Master)Up to 9 inverters (ports 1 to 9); 1 other device (port 10); MATE3 onlyPorts 1, 4, and 7 are required regardless of the number of slaves; also, the number of slaves should be even

Jumpers must be in “3-Phase/Split” position

Rev 002.013.000 or higher

Port 1Stack Mode Master

Port 2Stack Mode Slave

orOB Slave L1

Port 4

Stack Mode B Phase Master or3p Classic B

Port 7

Stack Mode C Phase Masteror3p Classic C

Also ports 3, 5, 6, 8, and 9

1st

MATE

Xor


Port 2Stack Mode 3phase OB Slave A

3phase OB Slave B3phase OB Slave C

Three-Phase StackUp to 9 inverters; 1 other device (MATE or MATE3)

10 9 8 7 6 5 4 3 2 1

Models

Ports 2 to 10 can be assigned any 3phase OB Slave stack mode;

no more than 3 inverters per mode Jumpers must be in “Single-phase” position

GTFX (E Series)

GVFX (E Series)

A

CBMaster B SlaveSlave

Back of HUB 10.3

10.63" (27 cm)

6.18" (15.7 cm)

1.27" (3.2 cm)

4.23" (10.7 cm)

9.24" (23.5 cm)

Dimensions

GS7048E

GFX

GFX (E Series)

Models

A

CB

Single-phase inverters:Three-phase output

PHASE A

PHASE B

PHASE C

Shutter Bushing x 2Snap Bushing x 2

or

Single-phase inverters:Three-phase output

Stacking HUB 10.3Stacking

10 9 8 7 6 5 4 3 2 1X

1st

MATE

FX / VFX (includes J, M, N Series)

ModelsPort 1

Stack Mode Master or 1-2phase Master

Port 2Stack Mode OB Slave L1

orOB Slave L2

Series Stack (OutBack)Up to 10 inverters or other devices (MATE or MATE3)Requires balancing transformer

HUB 10.3

Jumpers must be in “Single-phase” position



10 9 8 7 6 5 4 3 2 1X

1st

MATE

FX / VFX (includes J, M, N Series)

GTFX

GVFX

GTFX (LA Series)

GVFX (LA Series)

ModelsPort 1


Port 2

Stack Mode Classic Slave

Series Stack (Classic)2 inverters; up to 8 other devices (MATE or MATE3)

GFX

Jumpers must be in “Single-phase” position

10 9 8 7 6 5 4 3 2 1X

1st

MATE

GFXModels

Series Stack (Subphase Master) Up to 8 inverters (ports 1 to 4, 7 to 10); 2 other devices (ports 5, 6); MATE or MATE3No balancing transformer requiredImproves control of individual phase voltages and outputsPorts 2 to 4 are L1 slaves; ports 8 to 10 are L2 slaves despite the screen selection (OB Slave L1); equal inverters should be on L1 and L2Port 7 is the L2 subphase master despite the screen selection (Classic Slave); this port is required regardless of number of slaves

Jumpers must be in “3-Phase/Split” position


Port 2Stack Mode OB Slave L1

Also ports 3, 4, 8, 9, and 10

Port 7Stack Mode Classic Slave

1st

MATE

Xor

Port 1


Port 2

Stack Mode Slave or OB Slave L1

Parallel StackUp to 10 inverters or other devices (MATE or MATE3 where appropriate)

10 9 8 7 6 5 4 3 2 1GS8048

ModelsFX / VFX (all series, including E, J, M, N, and W)

Also port 3, etc.Jumpers must be in

“Single-phase” position

GS7048E

GFX

GFX (E Series)

(with FX-class inverter)

or

or

Single-phase inverters:Single-phase output

Split-phase inverters:Split-phase output

GTFX (E Series)

GVFX (E Series)

Single-phase inverters:Split-phase output


Ports 2 to 10 can be assigned to either OB Slave L1 or OB Slave L2;

equal numbers of inverters should be assigned to each side

or


stacking hub 10.3 quick start guide hub 10 · identified by mate3 on power-up: 3-phase/split...

Documents