sfs weather gard may08

7/17/2019 SFS Weather Gard May08

http://slidepdf.com/reader/full/sfs-weather-gard-may08 1/52

Weather Gard®

Product Guide



Weather Gard® Table of Contents

Section Page

Self-Drilling Fasteners

Impax™ Performance Drill Screws .................1

Impax™ Heavy Metal ThicknessStructural Drill Screws .................................2

Impax™ Sealer Drill Screws .............................3

Impax™ 1/4" Drill Screws ..............................4–5

Impax™ Insulated Panel Drill Screws .............6

irius® Drive Self-Drill

irius® Performance Drill Screws .................7–8

SX Stainless Self-Drill

SX Stainless Self-Drill ................................9–10

irius® SX Stainless Self-Drill .................... 11–12

Alloy Capped Fasteners

Zac

®

Impax

™

5/16" HWH Alloy Capped .......13Zac® Impax™ 3/8" HWH Alloy Capped

(for metal to metal) ...............................14–15

Zac® Impax™ 3/8" HWH Alloy Capped(for metal to metal and insulatedpanel to metal) .............................................16

Mac™ Impax™ Stainless Capped Self-Drill ...17

Zac® Tapping Fasteners .................................18

Prisma™ .............................................................19

Metal to Wood

Woodgrip™ Fasteners ...............................20–21

EVERGRIP™ Stainless Fasteners ...................22

Stainless Aluminum Panel Woodgrip™ .......23

Woodgrip™ Capped Fasteners ................24–25

Woodgrip™ #14 Milled Point ..........................26

Section Page

Self-Tapping Fasteners

Carbon Steel – Type A, AB, B .................27–28

Stainless Steel – Type A, AB, B .............29–30

#14 Milled Point – Type A ..............................31

Confas™ Concrete Fasteners .........................32

Panel Clips and Fasteners

Standing Seam Clips ............................... 33–34

Clip Fasteners ........................................... 35–36

WG-7™ Closure and Venting Products

WG-7™ Closure .................................................37

Pipe Flashing ....................................................38

ProfileVent® ......................................................39

Ventco™ Ridge Cap Anchor Clip ...................40

Tools, Belted Fasteners and Accessories

Installation Screw Guns .................................41

Panelmaster™ Belted Fasteners ....................42

Blind Rivets/Grommet Fasteners .................43

General Information

Fastener Design ........................................ 44–45

Washer and Fastener Head Styles ...............46

Structural Performance ..................................47

Coatings ............................................................48



Weather Gard® Self-Drilling Fasteners

Impax™— Performance Self-Drill 12-14 Impax and 1/4-14 Impax lap self-drilFor metal to meta

1SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0101-0907 ©2008 SFS intec, Inc.

• Precision cold forged assuring superior point strengthand the fastest drilling time performance through highstrength steel and nested purlins.

• Ultimate performance in light, mediumand heavy gage applications.

• Designed and engineered to have low driving and threadengagement torque and provide maximum clamp load.

• Mechanical zinc plated and coated with Silver Sentri™ for extended corrosion resistance.

Application

12-14 ImpaxMetal to metalDrilling capacity: .035 – .210

Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total.

Min projection: 3/16" of threadsbelow substrate

1/4-14 Impax LapPanel to panel side lapDrilling capacity: .030 – .095

Some applications may requireattaching light gage (24 – 26 ga)

to sub-structural member.Composite thicknessshould not exceed .095.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. Part No. Part No.Length #12 Bond Seal (15 mm) #12 No Washer 1/4-14 Impax Lap w/ Bond Seal 1/4-14 Lap No Washer

12-14 x 3/4 " SD3 A2361-EDF A2361F — —

12-14 x 3/4" SD2 S449 5-EDF S4495F — —

12-14 x 1" SD2 S4577-EDF S4577F — —

12-14 x 1-1/4" SD2 S46 32-EDF S46 32F — —

12-14 x 1-1/2" SD2 S4677-EDF S46 77F — —

12-14 x 2" SD2 S477 7-EDF S4777F — —

12-14 2-1/2" SD2 S4902-EDF S4902F — —12-14 x 3" SD2 S4952-EDF S4952F — —

12-14 x 4" SD2 S4981-EDF S4981F — —

1/4-14 x 7/8 " — — S5051-GUF S5051F

InstallationTools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.

5/16" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185

Strength (lbs ult.):Tensile: 3800Torsional: 150 in-lbsShear: 2850

Pull-out (lbs ult.):- 22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204


Strength (lbs ult.): Tensile: 2900Torsional: 92 in-lbsShear: 2050

Pull-out (lbs ult.): SD2 SD3 12 ga (.109) : 1539 148014 ga (.075) : 1010 82316 ga (.060 ): 724 624

Pull-over with Bond Seal (lbs ult.): 22 ga (.030): 124924 ga (.024): 1056

26 ga (.018): 654

OptionsSentri ™ Painted irius

ZAC®

MAC ™



Impax™ — Heavy Metal Thickness —Structural Drill Screws

12-24 Impax 4.5 and 5 self-drilFor metal to meta



Application

12-24 Impax 4.5Metal to metalDrilling capacity: .075 – .375

Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.

Thread length:12-24 x 1-1/4": .650


12-24 Impax 5Metal to metalDrilling capacity: .075 – .500

Thickness is based on normal,single thickness purlin/girt ormultiple material thickness.

Thread length:12-24 x 1-1/4": .52012-24 x 1-1/2": .77012-24 x 2": 1.020

Min projection: 3/16" of threads

below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listedare the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Selection Part No. Part No.Length Bond Seal (15 mm) No Washer

Impax 4.5

12-24 x 1-1/4" S4661-EDF S4661F

Impax 5

12-24 x 1-1/4" S466 8-EDF S466 8F

12-24 x 1-1/2" S4741-EDF S4741F

12-24 x 2" A2841-EDF A2841F



• Delivers ultimate performance in mediumand heavy gage applications.


• Zinc plated and coated with Silver Sentri™ for extendedcorrosion resistance.



Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): E xceeds tensile value1/4" (.250): Exceeds tensile value

Pull-over with Bond Seal (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584



Pull-out (lbs ult.):12 ga (.105): 13783/16" (.187): E xceeds tensile value1/4" (.250): Exceeds tensile value

Pull-over with Bond Seal (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584

OptionsSentri ™ Painted irius

ZAC®

MAC ™




Impax™— Sealer — Drill Screws 12-14 Impax sealer and 1/4-14 lap sealer self-drilFor metal to meta


• Integral cupped Hex Washer Head configuration fastenerwith an EPDM sealing washer instead of the traditionalbonded sealing washer.

• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength

steel and nested purlins.

• Delivers ultimate performance in light, mediumand heavy gage applications.


• Zinc plated and coated with Silver Sentri™ for extended

corrosion resistance.

Application

12-14 Sealer ImpaxMetal to metalDrilling capacity: .035 – .210



1/4-14 Sealer Impax LapPanel to panel side lapfrom .030 – .095Some applications may requireattaching light gage (24 – 26 ga)

to sub-structural member. Composite thickness should not exceed .095

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No.Length #12 Sealer 1/4-14 Sealer Lap

12-14 x 3/4" S448 6-FGF —

12-14 x 1" S4611-FGF —

12-14 x 1-1/4" X4636-FGF —

12-14 x 1-1/2" X4721-FGF —

1/4-14 x 7/8" — S5076-FF F


5/16" AF Cupped Hex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157


Pull-out (lbs ult.):12 ga (.105): 153914 ga (.075): 101016 ga (.060): 724

Pull-over (lbs ult.):

22 ga (.030): 129824 ga (.024) : 110226 ga (.018): 692

5/16 Cupped Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185



OptionsSentri ™ Painted




Impax™— 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drilFor metal to meta



• Impax #2 point is designed with a reduced drill point diameter to provide higher pullout in single purlin attachment.

• Delivers ultimate performance in mediumand heavy gage applications.


• Zinc plated and coated with Silver Sentri™

for extended corrosion resistance.

Application

1/4-14 Impax HWH #2 Point and #3 PointMetal to metalDrilling capacity:

#2 point: .050 – .150 #3 point: .050 – .210



1/4-20 Impax HWH #4 PointMetal to metalDrilling capacity:

.060 – .250

Thickness is based on normal,

single thickness purlin/girt ormultiple material thicknesscombined for total.


NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listedare the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

#2 – 5/16 AF Hex Washer Head #3 – 3/8" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185


#2 Point Pull-out (lbs ult.):12 ga (.105): 208814 ga (.075): 131216 ga (.060): 903

#3 Point Pull-out (lbs ult.):12 ga (.105): 169714 ga (.075): 115116 ga (.060): 687

Pull-over with Bond Seal (lbs ult.):22 ga (.030): 107924 ga (.024) : 88426 ga (.018): 616



Pull-out (lbs ult.):

12 ga (.030): 191314 ga (.024): 106116 ga (.018): 707

Pull-over with Bond Seal (lbs ult.):22 ga (.030): 111724 ga (.024) : 98826 ga (.018): 629

Continued on following page





Impax™— 1/4" Drill Screws 1/4-14 and 1/4-20 Impax self-drilFor metal to meta

Selection Part No. Part No. Part No. Part No. Part No. Part No. #3 & #4 Point #3 & #4 Point #2 Point Bond Seal #2 Point No Washer #2 Point Bond Seal #2 Point No WasherLength Bond Seal No Washer 5/16" HWH 5/16" HWH 3/8" HWH 3/8" HWH

1/4-14 x 3/4" S5010-GBF S5010F — — — —1/4-14 x 1" S5155-GBF S5155F — — S5171-GBF S5171F

1/4-14 x 1-1/4" S5201-GBF S5201F S5191-GBF S5191F — —

1/4-14 x 1-1/2" S5251-GBF S5251F S5286-GBF S5286F S5271-GBF S5271F

1/4-14 x 2" S5351-GBF S5351F — — — —

1/4-14 x 2-1/2" S5381-GBF S5381F — — — —

1/4-14 x 3" S5451-GBF S5451F — — — —

1/4-20 x 4" #4 Point S5621-GBF S5621F — — — —

1/4-20 x 5" #4 Point S5641-GB S5641 — — — —

1/4-20 x 6" #4 Point S5661-GB S5661 — — — —

1/4-20 x 7" #4 Point S5671-GB S5671 — — — —

1/4-20 x 8" #4 Point S5681-GB S5681 — — — —


OptionsSentri ™ Painted



Impax™— Insulated Panel Drill Screws Insulation fastenersFor metal to meta



• Designed for a particular thickness of insulated panel to insure uniform attachment without overdriving anddimpling the panel surface.

• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strength

steel and nested purlins.

• Delivers ultimate performance in light, mediumand heavy gage applications.


Application

12–14 InsulatedPanel FastenerDesigned for use in attachinginsulated foam panels to steelDrilling capacity: .035 – .210



below substrate

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners.

SelectionLength Insulated Panel Thickness Part No.

12-14 x 1-7/8" 3/4 " to 1" S7041-GBF

12-14 x 2-3/8" 1-1/8" to 1-1/2" S7061-GBF

12-14 x 3-1/4" 1-5/8" to 2-3/8" S7081-GBF



Strength (lbs ult):Tensile: 2900Torsional 92 in-lbsShear: 2050


Pull-over with Bond Seal (lbs ult.):

22 ga (.030) : 114824 ga (.024): 105626 ga (.018): 654

OptionsSentri ™ Painted ZAC®



Weather Gard® irius® Drive Self-Dril

irius® Performance Drill Screws irius 12-14, 12-24 self-drill and 1/4-14 lap self-drillFor metal to meta


• irius is a patented drive system adaptable to a full rangeof metal building fasteners.

• irius fasteners’ low profile head has changed the futurearchitectural appearance of side-wall fastening.

Applicatio

• Fastening system drive socket ensures positive engagementand prevents damage to a painted fastener head.

• Impax™ or SX self-drilling point design assures superiorpoint strength and excellent drill performance throughhigh strength steel.

irius low profile and drive system Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185


Pull-out (lbs ult.): 22 ga (.030): 37924 ga (.024): 30426 ga (.018): 204

Application12-14 irius Self-DrillMetal to metalDrilling capacity: .035 – .210



1/4-14 irius LapPanel to panel side lapDrilling capacity: .030 – .095


to sub-structural member.Composite thickness should notexceed .095 thickness.

12-24 irius 5

Metal to metalDrilling capacity: .075 – .550

Thickness is based on normal,single thickness purlin/girt ormultiple material thickness.

Thread length: 12-24 x 1-1/2": .770


Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled s teel material. Lap self-drill pull-out valuesis based on 40,0 00 psi AZ 55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered

and appropriate safety factors applied when specifying the proper fasteners. .

irius low profile and drive systemThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157




irius low profile and drive systemThread Major Dia: .216 – .208

Thread Minor Dia: .174 – .161Strength (lbs ult.): Tensile: 3450Torsional: 100 in-lbsShear: 2420

Pull-out (lbs ult.): 12 ga (.105): 19543/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value





Weather Gard® irius® Drive Self-Dril

irius® Performance Drill Screws irius 12-14, 12-24 self-drill and 1/4-14 lap self-drillFor metal to meta


Selection Part No. Part No. Part No. #12-14 Bond Seal 1/4-14 Lap 12-24 5.0Length 7/16 (12 mm) Length Bond Seal Bond Seal

12-14 x 1-1/4" S6632-F YF 1/4-14 x 7/8" S6851-HZF —12-14 x 1-1/2" S6677-FYF 12-24 x 1-1/2 (5) — S6741-FYF

12-14 x 2" S6777-FYF


OptioOptionsSentri ™ Painted

SX StainlessSelf-Drilling



Weather Gard® SX Stainless Self-Dril

SX Stainless Self-Drill SX austenitic stainless steeFor metal to meta


Application

SX 3-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity : .047 – .118

SX 6-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .079 – .236

SX 14-Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550

SX L2-Free Spin LapSelf-Drill5/8" O.D Bond SealMetal to metalDrill capacity: .031 – .079

5/16" AF Hex Washer HeadDia: Nominal #12



Pull-over (lbs ult.):24 ga (.024) : 119026 ga (.018): 665



Pull-out (lbs ult.):12 ga (.105): 112514 ga (.075): 85516 ga (.060 ): 610

Pull-over (lbs ult.):

24 ga (.024): 130026 ga (.018): 705



Pull-out (lbs ult.):12 ga (.105): 12203/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value

Pull-over (lbs ult.):24 ga (.024) : 115026 ga (.018): 646


Strength (lbs ult.):Tensile: 3600Torsional: 70 in-lbsShear: 360 0



• SX Austenitic stainless fasteners come with either a carbon steelspade point or the Bi-metal welded carbon steel point.

• SX Austenitic stainless product line offers fastening solutionsfor attaching panels from very thin to over 1/2" structural steel.

• Provides ultimate corrosion performance for attaching steel,

stainless or aluminum panels.• Designed for secured attachment to both panel and substructures.

• Stainless self-drill fasteners are engineered to havelow driving torque and provide maximum clamp load.

• Ultimate drill performance in light, medium, andheavy gage applications.

• Washer O.D designed for both sidewall and roof

panel attachment.




SX Stainless Self-Drill SX austenitic stainless steeFor metal to meta



Application continued

SX C-Self-Drill3/4" O.D Stainless Bond Seal

Insulated panel to metalDrill capacity : .157 – .551

SXCW-Self-Drill3/4" O.D Stainless Bond SealInsulated panel to wood

Drill capacity: .031 – .079

Selection U. S. Measurement Article No.

SX 3-Self-Drill

SX3/4-S16-5.5x22 #12-11 x 7/8" 0003356

SX3/10-S16-5.5x28 #12-11 x 1-1/8" 0003358

SX3/15-S16-5.5x38 #12-11 x 1-1/2" 0003 360

SX3/26-S16-5.5x50 #12-11 x 2" 0740424

SX3/20-34-S16-5.5x52 #12-11 x 2-1/8" 0003 363

SX3/20-44-S16-5.5x65 #12-11 x 2-1/2" 0027817

SX3/20-55-S16-5.5x75 #12-11 x 3" 0053144

SX 6-Self-Drill

SX6/6-S16-5.5x26 #12-14 x 1" 0003357

SX6/12-S16-5.5x32 #12-14 x 1-1/4" 0003359

SX6/15-S16-5.5x38 #12-14 x 1-1/2" 0003 364

SX 14-Self-Drill

SX14/12-S16-5.5x40 #12-14 x 1-1/2" 0770785

SX L2-Free Spin Lap Self-Drill

SXL2-S14-5.5x22 #12-11 x 7/8" 0003385

SXL2-S16-6.3x25 #14-14 x 1" 0003 369

InstallationTools: 0 – 2000 rpm screwdriver equippedwith depth sensing nosepiece.

5/16" AF Hex Washer HeadThread Major Dia: .213 – .207


5/16" AF Hex Washer HeadThread Major Dia: .255 – .249

Strength (lbs ult.):Tensile: 3732Torsional: 95 in-lbs

Shear: 2855

U. S. Measurement Article No. Panel Thickness

SX C-Self-Drill

SXC14-S19-5.5 x 80 #12-14 x 3-1/8" 0773620 1-1/2" – 2-1/16"

SXC14-S19-5.5 x 99 #12-14 x 3-3/4" 0775732 1-7/8" – 2-7/16"

SXC14-S19-5.5 x 118 #12-14 x 4-5/8 " 0776324 2-7/16" – 3-3/ 8"

SXC14-S19-5.5 x 138 #12-14 x 5-1/2" 07684 91 3-3/16" – 4"

SXC14-S19-5.5 x 168 #12-14 x 6-5/8 " 075788 0 3-15/16" – 5-7/32"

SXCW-Self-Drill

SXCW-S19-6.5 x 90 #14 x 3-1/2" 0998230 1-1/8" – 1-1/2"

SXCW-S19-6.5 x 105 #14 x 4-1/8" 09978 36 1-1/2" – 2"

SXCW-S19-6 .5 x 115 #14 x 4-9 /16" 099 8241 1-7/8" – 2-7/16"

SXCW-S19-6.5 x 135 #14 x 5-3/8 " 0997821 2-11/16" – 3-1/4"

SXCW-S19-6.5 x 155 #14 x 6-1/4" 09978 40 3-9/3 2" – 4"

OptionsPainted irius




irius® SX Stainless Self-Drill irius SX austenitic stainless steeFor metal to meta


• irius is a patented drive system available on a full rangeof metal building fasteners.

• irius SX stainless fasteners’ low profile head that has changed the future architectural appearance of sidewall fastening.

• Fastening system drive socket insures positive engagement

and prevents damage to a painted fastener head.

• Self-drilling point design assures superior point strength and the excellent drill performance through high strength steel.

• Stainless fasteners provide the ultimate corrosionperformance for attaching steel, stainless or aluminum panels.

• SX austenitic stainless self-drill fasteners are engineered to

have low driving torque and provide maximum clamp load.

Application

SX 3-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity : .047 – .118

SX 6-L12 irius Self-Drill1/2" O.D Aluminum Bond SealMetal to metalDrill capacity: .079 – .236

SX 14-L12 irius Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .157 – .550

SX L2-L12 irius Free SpinLap Self-Drill5/8" O.D Stainless Bond SealMetal to metalDrill capacity: .031 – .079

irius low profile and drive systemDia: Nominal #12



Pull-over (lbs ult.):24 ga (.024): 1300

26 ga (.018): 705




Pull-over (lbs ult.):24 ga (.024): 119026 ga (.018): 665

irius low profile and drive system

Dia: Nominal #12Strength (lbs ult.):Tensile: 4050Torsional: 70 in-lbsShear: 2700

Pull-out (lbs ult.):12 ga (.105): 122014 ga (.075): 718

Pull-over (lbs ult.):24 ga (.024): 115026 ga (.018): 646






irius® SX Stainless Self-Drill irius SX austenitic stainless steeFor metal to meta



Selection U. S. Measurement Article No.

SX 3-L12 irius Self-Drill

SX3/4-L12-A12-5.5x22 #12-11 x 7/8" 0996726SX3/10-L12-A12-5.5x28 #12-11 x 1-1/8" 0996727

SX3/15-L12-A12-5.5x38 #12-11 x 1-1/2" 0996680


SX6/6-L12-A12-5.5x26 #12-14 x 1" 0996719

SX6/12-L12-A12-5.5x32 #12-14 x 1-1/4" 0996720


SX14/12-L12-S16-5.5x38 #12-14 x 1-1/2" 0776328

SX L2-L12 irius Free Spin Lap Self-Drill

SXL2-L12-S14-5.5x22 #12-11 x 7/8" 0945591


OptionsPainted



Weather Gard® Alloy Capped Fasteners

ZAC® Impax™—5/16" HWH Alloy Capped

ZAC 5/16" HWHZinc aluminum capped drill screws

For metal to meta


• ZAC: the most widely used zinc aluminum cappedfastener in the industry.


• Integral cupped Hex Washer Head can never red rust.• Designed and engineered to have low driving and thread

engagement torque while providing maximum clamp load.

Application

12-14 ZAC (5/16")Metal to metalDrilling capacity: .035 – .210



1/4-14 ZAC Lap (5/16")Panel to panel side lapDrilling capacity: .030 – .095



NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values arebased on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing and we believe typical. The specific job conditions should beconsidered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nestedpurlins.

SelectionPart No. Part No.

Length 12-14 ZAC 1/4-14 ZAC Lap

5/16" AF Hex Washer Head ZAC

12-14 x 1" S4591-FLF

12-14 x 1-1/4" X4646-FLF —

12-14 x 1-1/2" X4731-FLF —

12-14 x 2" S4761-FLF —1/4-14 x 7/8" — S5031-FMF


5/16" AF Zinc Aluminum CappedHex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157


Pull-out (lbs ult.): 12 ga (.105): 153914 ga (.075): 101016 ga (.060 ): 724

Pull-over (lbs ult.): 22 ga (.030): 164724 ga (.024): 131026 ga (.018): 794




OptionsPainted




ZAC self-drill 3/8" HWHZinc aluminum capped drill screws

For metal to meta


14SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0402-09 07 ©2008 SFS intec, Inc.

• ZAC: the most widely used zinc aluminum capped fastenerin the industry.

• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strengthsteel and nested purlins.

• Designed and engineered to have low driving and threadengagement torque to prevent damage to the cap duringinstallation while providing maximum clamp load.

• Integral cupped Hex Washer Head can never red rust.

Application

12-14 ZAC (3/8")Metal to metalDrilling capacity: .035 – .210

Thickness is based on normal,single thickness purlin/girt or multiplematerial thickness combined for total.

Min projection: 3/16" of threadsbelow substrate.

1/4-14 ZAC Lap (3/8")Panel to panel side lapDrilling capacity: .030 – .095

Some applications may requireattaching light gage (24 – 26 ga) tosub-structural member. Composite

thickness should not exceed.095 thickness.

12-14 x 3/4 ZAC Lap (3/8" )Sharp pointPanel to panelDrilling capacity .030 – .060

Self-piercing points are not designedfor attaching light gage (24 – 26 ga)

to sub-structural member.

NotesDimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.




Pull-over (lbs ult.):22 ga (.030): 1647

24 ga (.024): 131026 ga (.018): 794






Pull-out (lbs ult.)22 ga (.030): 53824 ga (.024) : 43026 ga (.018): 330






ZAC self-drill 3/8" HWHZinc aluminum capped drill screws

For metal to meta


Selection Part No. Part No..Length 12-14 1/4-14 Lap)

3/8" Hex Washer Head ZAC

12-14 x 3/4 " A1653-FLF Sharp Point LAP —

12-14 x 1" S4576-FLF —

12-14 x 1-1/4" S46 31-FLF —

12-14 x 1-1/2" S46 76-FLF —

12-14 x 2" S4776-FLF —

12-14 x 2-1/2" S49 01-FLF —

12-14 x 3" S4951-FLF —

1/4-14 x 7/8" — S5065-FMF


OptionsPainted



ZAC® Impax™

3/8" HWH Alloy Capped

ZAC® self-drill 3/8" HWHZinc aluminum capped drill screws

For metal to metal and insulated panel to metal



• ZAC: the most widely used zinc aluminum capped fastenerin the industry.

• Precision cold forged assuring superior point strength and the fastest drilling time performance through high strengthsteel and nested purlins.

• Designed and engineered to have low driving and threadengagement torque to prevent damage to the cap duringinstallation while providing maximum clamp load.

• Integral cupped Hex Washer Head can never red rust.

Application

12-24 ZAC (3/8")4.5 point and 5 pointMetal to metalImpax 4.5Drilling capacity: .075 – .375

Impax 5Drilling capacity: .075 – .500

Thickness is based on single thickness purlin/girt or multiplematerial thickness combined for total.

Thread length:

ZAC 4.5: 12-24 x 1-1/4": .650 ZAC 5: 12-24 x 1-1/4": .52012-24 x 1-1/2": .770

12-24 x 2" : 1.020


12-14 InsulatedPanel FastenerDesigned for attachinginsulated foam panels to steel.Drilling capacity: .035 – .210

Thickness is based on normal,single thickness purlin/girt or

multiple material thicknesscombined for total.


Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out valuesare based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. PanelLength 12-14 Insulated 12-24 (4.5 ) and 12-24 (5) Thickness

12-24 x 1-1/4" (4.5) — S4665-FLF —

12-24 x 1-1/4" (5) — S4669-FLF —

12-24 x 1-1/2" (5) — S4742-FLF —

12-14 x 1-7/8" S7045-FMF 3/4" to 1"12-14 x 2-3/8" S7065-FMF 1-1/8" to 1-1/2"

12-14 x 3-1/4" S7085-FMF 1-5/8" to 2-3/8 "





Pull-over with assembledSeal washer (lbs ult.):

22 ga (.030): 164724 ga (.024): 131026 ga (.018): 794

3/8" AF Zinc Aluminum CappedThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157

Strength (lbs ult):Tensile: 2900Torsional: 92 in-lbsShear: 2050

Pull-out (lbs ult.):12 ga (.105): 1539

14 ga (.075): 101016 ga (.060): 724

OptionsPainted




MAC™ Impax™ —Stainless Capped Self-Drill

MAC stainless capped drill screwsFor metal to meta

17SFS intec, Inc. | Weather Gard® Product Group | 1-800-234-4533 WG0404- 0907 ©2008 SFS intec, Inc.

• MAC has a stainless capped, integral cupped Hex WasherHead configuration that can never red rust.


Application

12-14 MACAssembled with EPDM washerMetal to metalDrilling capacity: .035 – .210

Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total, as in overlappedor nested purlin construction.


1/4-14 MAC LapAssembled with EPDM washerPanel to panel side lapDrilling capacity: .030 – .095



12-24 MAC 4.5

Assembled with EPDM washerMetal to metalDrilling capacity: .075 – .375


Nominal thread length:12-24 x 1-1/4": .650


NotesDimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull out values are

based on 40,000 PSI AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing The specific job conditions should be consideredand appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.

Selection Part No. Part No. Part No.Length 12-14 MAC 1/4-14 MAC 12-24 MAC

12-14 x 1" S45 30-FAF — —

12-14 x 1-1/4" S4650-FAF — —

12-14 x 1-1/2" S4690-FAF — —

12-14 x 2" S4770-FAF — —

1/4-14 x 7/8" — S5100-GGF —

12-24 x 1-1/4" (4.5 ) — — S46 72-FAF

5/16” AF Stainless CappedHex Washer HeadThread Major Dia: .215 – .209Thread Minor Dia: .164 – .157



Pull-over (lbs ult.):22 ga (.030): 129824 ga (.024) : 110226 ga (.018): 692

5/16” A F Stainless Capped HexWasher HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185



5/16” AF Stainless Capped Hex Washer HeadThread Major Dia: .216 – .210

Thread Minor Dia: .186 – .181Strength (lbs ult.):Tensile: 3450Torsional: 100 in-lbsShear: 2420


Pull-over (lbs ult.):22 ga (.030): 104924 ga (.024): 86126 ga (.018): 584

InstallationTools: 0 – 2000 rpm screwdriver equipped with depthsensing nosepiece.

OptionsPainted



ZAC® Tapping FastenersZAC self-tapping fasteners

A and AB milled pointFor metal to meta



• Integral cupped Hex Washer Head configuration can never red rust.• Designed for attaching both metal to wood and metal to metal.

• Milled points do not require a pre-drilled hole whenattaching 26 and 24 gage metal to wood.

Application

1/4 -14 ZAC Type ABMilled PointMetal to woodMetal to metalSelf-Drilling Metal Thickness:Sheet .018 – .030

Thickness is based on normal,single or multiple material thicknesscombined for total

Min depth penetration into thewood sub structure: 1"

#17 Zac Type AB

Strip-out RepairMetal to metalRepair fastener for stripped out

#14 Type A or 1/4" AB


NotesDimensions are nominal inches unless noted. When using Milled point fasteners for metal to metal see the tapping screw section for performance values. Pull-out values(pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate valueslisted are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Selection Part No. Part No.Length 1/4-14 AB Length #17 AB

3/8" ZAC

1" A4395-FMF 17 x 1" A6045-LFF

1-1/2" A4485-FMF 17 x 1-1/2" A6066-LFF

2" A4513-FMF

2-1/2" A4510-FMF

InstallationTools: 0 – 1800 or 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.

3/8 AF Hex HeadThread Major Dia: .290 – .284

Thread Minor Dia: .220 – .214



Pull-out (lbs ult.): 22 ga (.030): 37924 ga (.024) : 30426 ga (.018): 204

OptionsPainted



Weather Gard® Capped Fasteners

Prisma™Nylon headed fasteners

self-tapping, self-drill and WoodgripFor metal to metal and metal to wood


• Prisma nylon head is absolutely corrosion proof.• Nylon head can withstand extreme installation torque without failure.

• Requires no special socket for installation.

• Special washer face allows the fastener to be usedon sidewall without a sealing washer.

• Nylon heads are available in 25 standard colors.

Application #14 Type ABMetal to metalSelf-Tapping AB:1/4-14 x 3/4"1/4-14 x 1-1/2"1/4-14 x 2"

Stainless AB:1/4-14 x 3/4"

Self-Drill:1/4-14 x 1"1/4-14 x 1-3/8"1/4-14 x 2"

Drill capacity: .050 – .210

1/4-14 x 7/8 LapMetal to metalPanel to panel side lapdrilling capacity: .030 – .095

Self-Drilling Metal Thickness:

Thickness is based on normal,single or multiple material thicknesscombined for total.

#10 WoodgripMetal to wood10 x 1"10 x 1-1/2"10 x 2"10 x 2-1/2"10 x 3"


NotesDimensions are nominal inches unless noted. For Type AB metal to metal, see tapping screw section for performance values.

OptionsNone

7/16" Nylon Hex Washer Head

1/4-14:Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185


1/4-14 AB Carbon Steel:


1/4-14 #3 Point Carbon Steel:

Pull-out: (lbs ult.): 12 ga (.105): 169714 ga (.075): 115116 ga (.060): 687

7/16" Nylon Hex Washer Head

1/4-14:Thread Major Dia: .246 – .240Thread Minor Dia: .192 – .185


Woodgrip Prisma 3/8" Nylon Hex Washer Head

Thread Major Dia: .199 – .191Thread Minor Dia: .133 – .127

Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs minShear: 933



Woodgrip™ Fasteners Woodgrip and HiLo WoodgripFor metal to wood

Weather Gard® Metal to Wood


Application

Woodgrip 9–15 HWHSharp PointAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)

Self-drills through the metal panel

and taps into wood substrate.Min penetration in wood substratesshould be no less than 1"

Woodgrip 9–15 HWHSharp PointMechanical Zinc-.001" minAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)

Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substratesshould be no less than 1"

HiLo Woodgrip 10 –15Assembled Bond Seal washerMetal to woodDrilling capacity: 24 ga (.024)


Woodgrip XG 12– 8 HWHSharp PointAssembled with Control SealMetal to woodDrilling capacity: 24 ga (.024)

Self-drills through the metal paneland taps into wood substrate. Large,aggressive thread design providessuperior resistance to strip-out, andsuperior performance in OSB, plywood,and 1x4" pine. Min penetration in woodsubstrates should be no less than 1"

NotesDimensions are nominal inches unless noted.

1/4" Hex Washer HeadThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127

Strength (lbs ult.): Tensile: 1500Torsional: 60 in-lbs min.Shear: 933





1/4" Hex Washer HeadThread Major Dia: .219 – .215

Thread Minor Dia: .133 – .127Strength (lbs ult.): Tensile: 2183Torsional: 60 in-lbs min.Shear: 1946

Woodgrip is the original sheet to wood fastenerdesigned to self-drill metal panels:• High Hex Washer Head provides driving stability

and a sharp point for quick installation.• Assembled with a control seal washer for a consistent,

weather tight seal and improved installation appearance.• Zinc plated and Silver Sentri™ coated for corrosion protection.• Alternate mechanical zinc (.001" min thick) plus Silver Sentri™

coated offers increased corrosion protection

HiLo Woodgrip is a sheet to wood fastenerdesigned to self-drill metal panels:• High Hex Washer Head provides driving stability

and a sharp point for quick installation.• Assembled with a bond seal washer for a consistent, weather

tight seal and improved installation appearance.• Zinc plated and Silver Sentri coated for corrosion protection.





Woodgrip™ Fasteners Woodgrip and HiLo WoodgripFor metal to wood


Application

Woodgrip 12 x 3/4 LapAssembled Bond Seal washerDrilling capacity: 2 x 24 gaPanel to panel side lap, end lapand other sti tch applications

Performance Pounds Ultimate Pull-out (lbs ult.) Wood: Spruce, Pine, Fir

#9 Woodgrip Control Seal Washer

1-1/2" Penetration 748

1" Penetration 542

#10 Hi Lo Woodgrip Bond Seal Washer


1" Penetration 524

% Increase Strip-outPull-out (lbs ult.) vs. Woodgrip (in-lbs)

#12 Woodgrip XG Control Seal Washer

SPF 1-1/2" Penetration 874 20

SPF 1" Penetration 571 20

1x4" Pine 590 34

3/4" Plywood 587 25

5/8" Plywood 446 31

1/2" Plywood 384 39

23/ 32" OSB 524 21

19/32" OSB 456 31

Notes: Woodgrip and HiLo pull-out strength values may vary from tested loads depending upon specific wooddensity variations. Woodgrip and HiLo pull-over strength values are based on .035" thick, 1/2" OD ControlSeal or Bond Seal washers, and have been updated to reflect common tensile strengths of metal panels asa function of panel thicknesses. Percent increase strip-out values of the Woodgrip XG over the standardWoodgrip are typical results, as encountered when fasteners are installed at 2500 rpm until full strip-outoccurs. Ultimate values listed are the result of laboratory testing. The specific job conditions should beconsidered, and appropriate safety factors applied, when specifying the proper fasteners.

SelectionSize Woodgrip HiLo Woodgrip Mechanical Zinc Woodgrip Woodgrip XG

1" C0161-CCF A1067-CDF C0167-CCF A1806-EMF1-1/2" C0261-CCF A1072-CDF C0267-CCF A1841-EMF

2" C0381-CCF A1077-CDF C0387-CCF A1851-EMF

2-1/2" C0461-CCF A1082-CDF C0467-CCF A1856-EMF

3" C0485-CCF A1087-CDF C0487-CCF A1861-EMF

12 x 3/4 " (1/4" HWH) A1701-ECF A1701-EAF – –

InstallationTools: 0 – 2500 rpm screw driver equipped withdepth sensing nose piece.

OptionsSentri ™

Color Sentri ™

COLOR

Painted ZAC®

ZAC

MAC ™

MAC

Pull-over

28 ga (110 ksi): 577

26 ga (70 ksi): 63724 ga (70 ksi): 800

28 ga (110 ksi): 577

26 ga (70 ksi): 637

24 ga (70 ksi): 800

1/4" Hex Washer Head:Thread Major Dia: .215 – .208Thread Minor Dia: .164 – .157


Pull-over

28 ga (110 ksi): 577

26 ga (70 ksi): 637

24 ga (70 ksi): 800

Fasteners installed in less than 1" of solid wood mayhave an increased potential for sealing or connectionfailure over time. This may be due to the fasteners beingstripped out during installation and/or due to the lackof adequate wood fiber material to hold the fastener inplace during thermal movement cycles or other forceswhich may be exerted upon the connection.



EVERGRIP™ Stainless Fasteners EVERGRIP stainless bi-metaFor metal to wood



EVERGRIP stainless wood fastener is designed to self-drill metal panels:• Head and the majority of shank is 304 Stainless Steel, with a

welded, hardened carbon steel point for self-drilling performance.• Provides the corrosion protection of stainless with the drill

performance of a carbon steel fastener.

• Designed specifically for corrosion resistance in new wood treatments (ACQ/CA).

Application

EVERGRIP9 – 15 HWH Sharp PointAssembled withstainless Bond SealMetal to woodDrilling capacity: 24 ga (0.024)

Self-drills through the metal paneland taps into wood substrate.Min penetration in wood substrates

should be no less than 1"

EVERGRIP9 – 15 T-25 (TORX®) Pan HeadAssembled withstainless Bond SealMetal to woodDrilling capacity: 24 ga. (0.024)


Performance Pounds Ultimate Pull-out (lbs ult.)

Wood: Spruce, Pine, Fir

EVERGRIP Stainless Bond Seal


1" Penetration 542

Notes: Dimensions are nominal inches unless noted. Pull out strength values mayvary from tabulated loads depending upon specific wood density variations.Pull over strength values are based on AZ55 Galvalume steel material.Ultimate values listed are the result of laboratory testing. The specific jobconditions should be considered and appropriate safety factors applied.

Selection HWH HWH T-25 Pan HeadLength 250/Bag 100/Box 250/ Bag

1" E4160-CUF E4160-CUEG 1119934

1-1/2" E4260-CUF E4260-CUEG 1124180

2" E4380-CUF E4380-CUEG 1119937

2-1/2" E4460-CUF E4460-CUEG —

3" — — 1119938

Description Part No. Quantity

SFS Special T-25 Torx drive bit 0514261 1 each


The EVERGRIP 9-15 T-25 (TORX) Pan Headrequires a T-25 Torx drive bit.

Utilizing the special SFS T-25 Torx drivebit manufactured by SFS intec isrecommended for superior stabilityduring the installation process.

OptionsPainted

1/4" Hex Washer HeadThread Major Dia: 0.181 – 0 .175Thread Minor Dia: 0.133 – 0.127


Pull-over

28 ga: 378

26 ga: 519

24 ga: 704

T-25 (TORX ) Pan HeadHead Dia: 0.393 –0.374”Thread Major Dia: 0.181 – 0 .175Thread Minor Dia: 0.133 – 0.127


Utilizing the special SFS T-25 Torx drivebit manufactured by SFS intec isrecommended for superior stabilityduring the installation process.

Fasteners installed in less than 1" of solid wood may have an increased potentialfor sealing or connection failure over time. This may be due to the fasteners beingstripped out during installation and/or due to the lack of adequate wood fibermaterial to hold the fastener in place during thermal movement cycles or otherforces which may be exerted upon the connection.




Stainless Aluminum Panel Woodgrip™ Woodgrip stainlessFor aluminum pane


Stainless, Aluminum Panel Woodgrip is an all stainlesswood fastener designed for use with aluminum panels:• Fastener is 304 stainless steel for corrosion protection.• High hex washer head provides driving stability

and a sharp point for quick installation into aluminum.

• Will not drill steel panels.

Application

StainlessAluminum Panel Woodgrip9 – 15 HWH Sharp PointAssembled withaluminum Bond SealMetal to woodSelf-drills through aluminum paneland taps into wood substrate.Min penetration in wood substrate

should be no less than 1"


#9 Woodgrip Stainless Aluminum Bond Seal


1" Penetration 542

Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads dependingupon specific wood density variations. The specific job conditions should be considered and appropriatesafety factors applied. Stainless Woodgrips are not designed to self-drill steel panels.

Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failureover time. This may be due to the fasteners being stripped out during installation and/or due to the lack of adequatewood fiber material to hold the fastener in place during thermal movement cycles or other forces which may beexerted upon the connection.

SelectionSize Stainless Woodgrip

1" E0225-CKF

1-1/2" E0270-CKF

2" E0272-CKF

2-1/2" E0275-CKF

3" E0277-CKF


OptionsPainted

1/4" Hex Washer headThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127

Strength (lbs ult.): Tensile: 1657Torsional: 50 in-lbs minShear: 1550



Woodgrip™ Capped Fasteners WoodZAC® and WoodMACFor metal to wood



WoodZAC has all the performance features ofstandard Woodgrip fasteners, plus a zinc alloycap that can never red rust:• 5/16" AF high Hex Washer Head for driving stability

and a sharp point for quick installation.

• Assembled with a aluminum bond seal for weather tightseal and improved installation appearance.

WoodMAC has all the performance featuresof standard Woodgrips:• 1/4" AF stainless cupped HWH for a low profile appearance

and can never rust.

Application

WoodZAC9–15 HWH Sharp PointAssembled withaluminum Bond SealMetal to woodDrilling capacity: 24 ga (.024)


WoodZAC12 x 3/4" LAP Sharp PointAssembled with EPDM washerPanel to panel side lap, end lapand other sti tch applications

WoodMAC9–15 HWH Sharp PointAssembled with EPDM washerMetal to woodDrilling capacity: 24 ga (.024)


WoodMAC Lap12 x 3/4" HWH Sharp PointAssembled EPDM washerPanel to panel side lap, end lapand other sti tch applications


5/16" Hex Washer HeadZinc Alloy CapThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127


5/16" Hex Washer HeadZinc Alloy CapThread Major Dia: .215 – .208Thread Minor Dia: .164 – .157


1/4" Cupped Stainless CappedThread Major Dia: .181 – .175Thread Minor Dia: .133 – .127


1/4" Cupped Stainless CappedThread Major Dia: .215 – .208

Thread Minor Dia: .164 – .157Strength (lbs ult.): Tensile: 2100Torsional: 92 in-lbs min.Shear: 1800





Woodgrip™ Capped Fasteners WoodZAC® and WoodMACFor metal to wood



#9 Woodgrip 5/16" ZAC Aluminum Bond Seal


1" Penetration 542

#9 Woodgrip 1/4" MAC EPDM Washer


1" Penetration 542

Notes: Woodgrip and WoodZAC pull out strength values may vary from tabulated loads depending upon specific wood density variations.Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safetyfactors applied when specifying the proper fasteners.

Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time.This may be due to the fasteners being stripped out during installation and/or due to the lack of adequate wood fiber material

to hold the fastener in place dur ing thermal movemen t cycles or other force s which may be exerted upon the conn ection.

SelectionSize WoodZAC WoodZAC Lap WoodMAC WoodMAC Lap

1" C0165-DNF — C0168-CAF —

1-1/2" C0265-DNF — C0268-CAF —

2" C0385-DNF — C0388-CAF —

2-1/2" C0465-DNF — C0468-CAF —

3" C0481-DNF — C0488-CAF —

12 x 3/4" ZAC (5/16" HWH) — A1705-FLF — —

12 x 3/4 " MAC (1/4" HWH) — — — A1708-E YF

InstallationTools: 0 – 2500 rpm screw driver equipped with depth sensing nose piece.

OptionsPainted

Pull-over

28 ga: 433

26 ga: 570

24 ga: 900

28 ga: 380

26 ga: 500

24 ga: 710



Woodgrip™ #14 Milled PointMilled point — Type A milled point

and Type AB ZACFor metal to wood



Milled Point carbon steel self-tapping fastenersare designed for attaching both metal to woodand metal to metal:• These fasteners do not require a pre-drilled hole when attaching

26 and 24 gage metal to wood.

ZAC® Milled Point tapping screws have the sameperformance features of milled point tappers with:• Zinc alloy capped head that can never red rust.• Assembled with EPDM sealing washers for a consistent,

weather tight seal.

Application

#14 Type A Milled PointCarbon Steel, Silver SentriMetal to woodSelf-drilling metal thickness:Sheet .018 – .030



#14 ZAC Type AMilled PointMetal to woodSelf-drilling metal thickness:Sheet .018 – .030



1/4 ZAC Type AB

Milled PointMetal to woodSelf-drilling metal thickness:Sheet .018 – .030



Notes Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel material. Ultimate values listed

are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Selection Part No. Part No. Part No.Length #14 A Milled Point Bond Seal #14 A Milled Point 3/8" ZAC 1/4" AB Milled Point 3/8" ZAC

1" A3321-GBF A3325-FMF A4395-FMF

1-1/4" — — A442 8-FMF

1-1/2" A3438-GBF — A4485-FMF

2" A3531-GBF — A4513-FMF

2-1/2" A3597-GBF — A4510-FMF

3" A3626-GBF — —




Pull-out (lbs ult.): 1" SPF wood: 1013

Pull-over ( lbs ult.): 22 ga (.030): 109724 ga (.024): 81026 ga (.018): 564

3/8" AF Zinc Alloy CappedThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178




3/8" AF Zinc Alloy CappedThread Major Dia: .246 – .240

Thread Minor Dia: .192 – .185Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 2500


Pull-over (lbs ult): 22 ga (.030): 109424 ga (.024): 86626 ga (.018): 600

OptionsPainted



Weather Gard® Self-Tapping Fasteners

Tapping Screws—Carbon Steel Self-tapping—Type A, AB, BFor metal to meta


• Carbon steel zinc-plated self-tapping fasteners are the original metalconstruction fastener that can be used in metal to metal and metal to wood applications.

• Tapping screws are available in long lengths for specialty applications.

Application

#14 Type AMetal to metalAttachment thickness: .044 – .075

Metal thickness Drill bit size.021 – .026 1/8 (.125).027 – .050 3/16 (.187).051 – .075 #8 (.199)

The hole size determines installationperformance and pullout strength.

Thickness is based on normal, single thickness purlin/girt or multiplematerial thickness combined for total.


below substrate

1/4 Type AB and BMetal to metalAttachment thickness: .044 – .500

Metal thickness Drill bit sizeAB .021 – .026 1/8 (.125)AB .027 – .050 5/32 (.156)AB .051 – .075 #8 (.199)AB .075 – .110 #7 (.201)B .065 – .085 #8 (.199)B .085 – .115 #7 (.201)B .115 – .375 #1 (.228)B .375 – .500 #1 or larger, depending on hardness of steel

Thickness is based on normal,single thickness purlin/girtor multiple material thicknesscombined for total.


#17 Type ABStrip out repair Type A or ABMetal to metalAttachment thickness: .03 6 – .06 0


NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the resultof laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

3/8" AF Hex HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178




3/8" AF Hex HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185

Strength (lbs ult.): Tensile: 3800Torsional:142 in-lbsShear: 2560



3/8" AF Hex Head Thread Major Dia: .295 – .285 Thread Minor Dia: .220 – .214




Tapping Screws—Carbon Steel Self-tapping—Type A, AB, BFor metal to meta



Selection Part No. Part No. Part No.Length* #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal

3/4" A2980-GB A4320-GB A3800-GB

1" A3240-GB A4420-GB A3860-GB

1-1/4" A3420-GB A44 40-GB —

1-1/2" A346 0-GB A4500-GB A3920-GB

2 " A3520-GB — A400 0-GB

2-1/2" A3580-GB — A404 0-GB

3" A3620-GB — A4080-GB

3-1/2" A364 0-GB — A4140-GB

4" A368 0-GB — A4220-GB

5" A3720-GB — A4260-GB

6" A3740-GB — A4280-GB

#17 x 3/4" — A6020-K J —

#17 x 1" — A6040-KJ —

#17 x 1-1/2" — A6060-K J —

*Longer lengths available upon request

InstallationTools: 0 – 1000 rpm on type B screwdriver equipped with depth sensing nosepiece.





Tapping Screws—Stainless Steel Stainless self-tapping—Type A, AB, BFor metal to meta


• Stainless steel zinc-plated self-tapping fasteners aredesigned for attaching metal to metal and metal to wood.

• Type B have wax surface treatment for added lubricity.

• Stainless tappers are used in high corrosive environmentsor where corrosions free performance is required to meet

the design life of the project.

Application

#14 Type A 304 StainlessMetal to metalAttachment thickness: .044 – .075Metal thickness Drill bit size.021 – . 026 1/8 (.125).027 – . 050 3/16 (.187).051 – . 075 #8 (.199)

The hole size determines installationperformance and pullout strength.



Type AB and B 304StainlessMetal to metalAttachment thickness: .04 4 – .50 0

Metal thickness Drill bit sizeAB .021 – .026 1/8 (.125) AB .027 – .050 5/32 (.156) AB .051 – .075 #8 (.199) AB .075 – .104 #7 (.201)

B .065 – .085 #8 (.199)B .085 – .115 #7 (.201)

B .115 – .375 #1 (.228) B .375 – .500 #1 or larger, depending on hardness of steel



#17 Type AB 304 StainlessStrip out repair Type A or ABMetal to metalMin projection: 3/8" of threadsbelow substrate

NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the resultof laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

3/8" AF 304 Stainless Hex HeadThread Major Dia: .254 – .248Thread Minor Dia: .185 – .178


Pull-out (lbs ult.) 14 ga (.075): 123216 ga (.060): 1110


3/8" AF 304 Stainless Hex HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185

Strength (lbs ult.): Tensile: 3800Torsional: 142 in-lbsShear: 235 0



3/8" 304 Stainless AF Hex HeadThread Major Dia: .295 – .285Thread Minor Dia: .220 – .214




Tapping Screws—Stainless Steel Stainless self-tapping—Type A, AB, BFor metal to meta



Selection Part No. Part No. Part No.Length #14 A Bond Seal 1/4 AB & #17 AB Bond Seal 1/4 B Bond Seal

3/4" E0500-HP E1240-HP E0860-HPW

1" E0600-HP E1300-HP E0880-HPW

1-1/4" E0640-HP E1310-HP —

1-1/2" E0660-HP E1320-HP E1000-HPW

2" E0700-HP — E1060-HPW

2-1/2" E0720-HP — E1080-HPW

3" E0740-HP — E1100-HPW

3-1/2" E0760-HP — E1120-HPW

4" E0780-HP — E1140-HPW

5" E0820-HP — E1180-HPW

6" E0840-HP — E1200-HPW

7" E0850-HP — E1210-HPW

8" E0855-HP — E1215-HPW

#17 x 3/4" — E1960-KP —

#17 x 1" — E1980-KP — #17 x 1-1/2" — E2000-KP —


OptionsPainted




Tapping Screws — Milled Point Self-tapping #14 milled point Type AFor metal to wood and metal to meta


• Milled point carbon steel self-tapping fasteners are designedfor attaching both metal to wood and metal to metal.

• Milled point fasteners do not require a pre-drilled hole whenattaching 26 and 24 gage metal to wood.

• For attaching metal to metal they have the same performanceas standard A tappers. See tapping screw section.

• Zinc plated and Silver Sentri™ coated for extendedcorrosion resistance.

Application #14 Type A Milled PointMetal to woodMetal to metalSelf-Drilling Metal Thickness:Sheet .018 – .030


Min penetration into the woodsub structure: 1"

NotesDimensions are nominal inches unless noted. Pull out values (pounds ultimate) are based on 50,000 psi hot rolled steel material. Ultimate values listed are the result of laboratory testing. T he specific job conditions should be considered and appropriate safe ty factor s applied when specifying the proper fas teners.

Selection Part No.Length #14 A Milled Point Bond Seal

1" A3321-GBF

1-1/2" A3438-GBF

2" A3531-GBF

2-1/2" A3597-GBF

3" A3626-GBF




Pull-out (lbs ult.): 1" SPF Wood: 1013





Confas™ Concrete FastenersConfas concrete tappers—

Carbon steel and 304 stainless steeFor attachment to concrete

Weather Gard® Self Tapping Fasteners


• Confas — Slotted Hex Washer Head and Phillips/flathead anchoring system for concrete, block and brick.

• One-piece system provides many installation benefitswith exceptional performance.

• Exclusive in-house applied Sentri XP™ coating, providingexcellent resistance to rust and corrosion.

• 304 austenitic stainless provides ultimate corrosion performance.

Application3/16" DiameterAvailable lengths:1-1/4" to 4"Carbon Steel304 StainlessSlotted Hex Washer HeadPhillips flat headSpecial close tolerance bitsare required to ensuresystem performance.

The hole tolerance differs forcarbon steel and stainless,so bit selection is of importance.

It is recommended that the hole depthexceeds the fastener length by 1/2".However, penetration beyond 1-1/2"is not desirable.

1/4" DiameterAvailable lengths:1-1/4" to 6"Carbon Steel304 Stainless

Slotted Hex Washer HeadPhillips flat headSpecial close tolerance bitsare required to ensuresystem performance.

The hole tolerance differs forcarbon steel and stainless,so bit selection is of importance.

It is recommended that the hole depthexceeds the fastener length by 1/2".However, penetration beyond 1-1/2"is not desirable.

Notes

Dimensions are nominal inches unless noted. Performance of Confas is subject to proper hole size and characteristics of the masonry material into which the anchors aredriven. Ultimate values listed are the result of laboratory testing. Since safety factors can vary from job to job, application reference should always be made to the applicablecodes for specific safe working ratios. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

OptionsNone

1/4" Slot ted Hex Washer Head #3 Phillips Flat HeadThread Major Dia: .215 – .205Thread Minor Dia: .127 – .123

Recommended hole s ize:0.168 – .0175

Pull-out 1-1/4" penetration (lbs ult.): Concrete slab: 1700Hollow block: 580Face brick: 990

Typical shear values (lbs ult.): Concrete block:Solid limestone: 683(132 lbs per cubic feet)

Concrete block:Expanded slag: 917(116 lbs per cubic feet)

Red clay brick: 1067(136 lbs per cubic feet)

Poured concrete: 1133(6800 psi)

5/16" Slotted Hex Washer Head #3 Phillips Flat HeadThread Major Dia: .255 – .245Thread Minor Dia: .172 – .168

Recommended hole s ize:.0202 – .0204

Typical shear values (lbs ult.):

Concrete block:Solid limestone: 1017(132 lbs per cubic feet)

Concrete block:Expanded slag: 1083(116 lbs per cubic feet)Red clay brick: 1583(136 lbs per cubic feet)Poured concrete: 193 3(6800 PSI)

Pull-out 1-1/4" penetration (lbs ult.): Concrete slab: 1767Hollow block: 647Face brick: 1050



Weather Gard® Panel Clips and Fasteners

Standing Seam Clips Engineered panel clipsFor standing seam panel attachments


• Engineered panel clips are custom designed and manufacturedfor your panel system.

• Clips are supplied in galvanized steel, coated steel,stainless steel and other materials.

• Engineered fixed and float clip designs are available.

• Standard clips are available from stock without tooling cost to you.• Sealant can be pre-applied to the clips to maintain the seal

at the clip attachment.• Clip design options are available for review and evaluation.

Application

Snap Lock Panel DesignConfigurations require very low profileclip bases with a base feature to hold

the panel above the low profilefastener heads.

Selection

1-1/2" Snap Lock ClipG90 Galvanized: 18 ga. or 20 ga.Packaged 500 per carton

1-3/4" Snap Lock(1 hole) ClipG90 Galvanized: 18 ga.Packaged 500 per carton


Application

Architectural Panel DesignConfigurations require low profilebases with clearance for thefastener head.

Fixed Clips are primarily used with thesepanels. Low profile head fasteners shouldbe used with these panels to provideclearance for the panel over the fastenerheads. These clips are manufactured fromsteel, stainless steel and other materialswith various finishes to fit the needs of thepanel application.

Roof Panel

Roof Panel

Clip

BlanketInsulation

Roof Purlin

Low ProfileHead Fastener

1-1/2" Snap Lock ClipG90 Galvanized: 24 ga.Packaged 1000 per carton


Fixed and Float Clips are used with thesepanels. The clips may have pre-appliedsealant to maintain the panel seal at theclip attachment point. These clips aremanufactured from steel, stainless steeland other materials with various finishes to fit the needs of the panel application.

Roof Panel

Sliding ClipAssembly

BlanketInsulation

Roof Purlin

Roof Panel




Standing Seam Clips Engineered panel clipsFor standing seam panel attachments



Selection

1-1/2" Single Lock Fixed ClipG90 Galvanized: 22 ga.

Packaged 700 per carton

2" Single Lock Fixed ClipG90 Galvanized: 22 ga.Factory applied sealantPackaged 250 per carton

2" Single Lock Utility ClipG90 Galvanized: 22 ga.Factory applied sealantPackaged 400 per carton

2" Double Lock Fixed ClipG90 Galvanized: 22 ga.

Factory applied sealantPackaged 250 per carton

2" Double Lock Fixed Clipwith Panel ShelfG90 Galvanized: 22 ga.Factory applied sealantPackaged 250 per carton

OptionsAlso Available in Stainless Steel

2" Single LockFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged 100 per carton

2" Double LockFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged 100 per carton

1-1/2" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton

2" Mechanical SeamFloat Clip

G90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton

2" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Factory applied sealantPackaged Low 100 per cartonor High 70 per carton

3" Mechanical SeamFloat ClipG90 Galvanized: 22 ga.Base: 16 ga.Packaged 80 per carton




Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood


• Designed with unique head styles, drill pointconfigurations and material types to meet performancerequirements to attach standing seam roof clips.

• Engineered profile features preventing paneldamage from fastener head contact.

• Engineered installation torque drive controlfor uniform installation performance.

Application #10 Type A: Pancake Head2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to wood

#10 Type A: Pancake HeadPhillips DriveStainless SteelMetal to wood

#10 Self-Drill: Pancake Head2/2 Quadrex Drive

Carbon Steel, Zinc PlatedMetal to metalMin projection: 3/8" of threadsbelow substrate

#12–8 XG Sharp Point: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood

#12 Type A: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to wood

#12 Self-Drill: Pancake Head2/2 Quadrex DriveCarbon Steel , Zinc PlatedMetal to metalMin projection: 3/8" of threadsbelow substrate .

Head Height: .080 – .068Head Dia: .447 – .423Thread Major Dia: .194 – .188Thread Minor Dia: .133 – .126

Strength (lbs ult.): Carbon Stainless Tensile: 1825 1653Torsional: 48 in-lbs 50 in-lbsShear: 1535 1587

#10 Type A, Pull-out (lbs ult.):

SPF wood:1" penetration: 821

#10 Self Drill, Pull-out (lbs ult.): 12 ga (.105) : 178214 ga (.075): 107216 ga (.060): 782

Roof Panel

Roof Panel

Clip

BlanketInsulation

Roof Purlin

Low ProfileHead Fastener



Pull-out (lbs ult.): SPF wood:

1" penetration: 724

Head Height: .080 – .068Head Dia: .447 – .423Thread Major Dia: .215 –.209Thread Minor Dia: .113–.127


Performance (lbs ult.): Pull-out SPF 1-1/2" Penetration 874SPF 1" Penetration 5711x4" Pine 5903/4" Plywood 5875/8 " Plywood 4461/2" Plywood 38423/ 32" OSB 52419/32" OSB 456



Pull-out (lbs ult.): 12 ga (.105) : 153914 ga (.075): 101016 ga (.060): 724




Clip Fasteners Clip attachment fastenersFor metal to metal, metal to wood



Application

1/4 -14 #2 PointDrilling capacity (#2 point): .050 – .150

Attachment thickness:Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.


12-24 #5 Point: Pancake Head2/2 Quadrex DriveCarbon Steel, Zinc PlatedMetal to metal

Drilling capacity: .075 – .500Attachment thickness:Thickness is based on normal,single thickness purlin/girt ormultiple material thicknesscombined for total.

Min projection: 3/8” of threadsbelow substrate

NotesDimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result oflaboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.

Fasteners installed in less than 1" of solid wood may have an increased potential for a connection failure over time. This may be due to the fastener s being stripped out duringinstallation and/or due to the lack of adequate wood fiber material to hold the fastener in place when forces are exer ted upon the connection.

Selection

5/16" AF Hex Washer Head3/8" AF Hex Washer HeadThread Major Dia: .246 – .240Thread Minor Dia: .192 – .185


#2 Point, Pull-out (lbs ult.): 12 ga (.105): 208814 ga (.075): 131216 ga (.060): 903

BlanketInsulation

Roof Panel

Roof Purlin

Roof PanelClip

Roof Panel

OptionsSentri ™


Strength (lbs ult.): Tensile: 3450

Torsional: 100 in-lbsShear: 2420

Pull-out (lbs ult.): 12 ga (.105): 13783/16" (.187): Exceeds tensile value1/4" (.250): Exceeds tensile value

InstallationTools: 2000 – 2500 rpm #10 self drill, 0 – 2000 rpm on 1/4-14 self drill screwdriver equipped with depth sensing nosepiece.

Length

#10 Type APancake

Carbon Steel

#10 Type APancake

Stainless Steel #10 Self-Drill

Pancake #12–8 XGPancake

#12 Type APancake

#12 Self-DrillPancake

12–24 #5 PointPancake

1/4–14 #2 Point5/16 AF HWH

1/4–14 #2 Point3/8 AF HWH

1" A1191F E0235F S3431F A1900F A1710F S4552F — — S5171F

1-1/4" — — — — — — — S5191F —

1-1/2" A1351F — S4221F A1940F — — S4750F S5286F S5271F

2" A1391F E0271F S4421F A1950F — — — — —



Weather Gard® Closure and Venting Products

WG-7™ Closure WG-7 closure and WG-7 adhesive closureFor panel opening fille


• The original industry closure material — time tested-millionsof feet installed over the last 30-plus years.

• Polyethylene foam for exceptional strengthand compressibility.

• Most configurations are cut with dovetails that eliminate

gapping between pieces.

• Moisture and water vapor transmission is barely measurable.• Adhesive applied to the contact side of the panel surface

assures positive positioning during installation.• Resist damaging ultra violet rays and ozone deterioration.• Over 1800 panel configurations available.

• Manufactured in multiple plants for quick delivery.

Typical Inside Closure Application Typical Outside Closure Application

Endwall

Closure

Roof Panel

SidewallRoof Panel

EndwallClosure

Sidewall

Application

WG-7 ClosureMaterial Thickness: 1", 1-1/2", 2"

Color: Grey

FeaturesProperty Units Properties*

Nominal density lb/f t3 1.5 – 2.0Skin/Skin

Recommended operating degrees F +212 max temperature range -94 min

Compression stress-strain characteristics

10% compression psi 4.64



Compression set

(22 hrs, 25% compression, 23˚C)

1/2 hour recovery % set 12

24 hour recovery 5

Tear strength ft-lbs 295

Tensile strength psi 46.27

Elongation % 102

Thermal conductivity

(at mean temp of 50˚ F) BTU/ ft-hr.-degrees F 0.02 3

Horizontal Burning Characteristics Burn Rate

0.197" thickness in/sec 0.0830.512" thickness in/sec 0.059

FMVSS. 302 (pass thickness) in 0.394" and above

Shore Hardness 00 scale

(min. 0.394" cell/cell thickness) 43

*All properties are nominal values and are subject to change.

OptionsNone



Pipe Flashing Square and round base pipe flashingFor roof pipe flashing



Application

Square BaseSize Pipe size Base size

1 1/4 – 2" 4-1/2"

2 1-1/4 – 3" 6"

3 1/4 – 4" 8"

4 3 – 6" 10"

5 4 – 7" 11"

6 5 – 9" 12"

7 6 – 11" 14"

8 7 – 13" 17"

9 10 – 18" 25"10 13 – 26" 34"

Round BaseSize Pipe size Base Size

1 1/4 – 2" 4-3/4"

2 1-3/4 – 3-1/4" 6-1/4"

3 1/4 – 5" 7-3/4"

4 3 – 6-1/4" 9-1/4"

5 4-1/4 – 7-1/2" 10-3/4"

6 5 – 9" 12-1/4"

7 6 – 11" 14-1/4"

8 7 – 13" 16-1/2"

9 10 – 19" 25-1/2 "

Retrofit Square BaseSize Pipe size Base Size

1 1/2 – 4" 8-3/16"

2 4 – 9-1/4" 14-1/4"

3 9-1/4 – 16-1/4" 21-1/2"

Material SpecificationsTest Type EPDM Silicone (Hi-Temp)

Advance ozone resistance

70 Hrs. 70 Hrs. test @ 500 pphmHigh temperature:

Intermittent +275º F +500º F

Continuous +212º F +437º F

Low temperature:

Resistance tested to -65º F -100º F

Tensile strength 1450 psi 700 psi

OptionsNone

• Pipe opening can be easily customized on job sightutilizing clearly marked pipe diameters on each flashing.

• EPDM and Silicone are both flexible materials, resistant to ultraviolet rays, cracking or weathering.

• Available in EPDM black or gray and silicone red.

• The aluminum base is corrosion resistant and conformseasily to any panel configuration or roof pitch.

• Retrofit flashing is available for piping with welded capsor cross bars.

• Square base also available in white, terra cotta, bright red,

light green, dark green, light blue, dark blue and brown.




ProfileVent® Metal roofing ridge vent


• 40 year limited warranty

• Glue spots prevent slippingduring installation

• Fits under any ridge cap

• Fits any pitch 2:12 – 20:12• One person roll-out installation

• Won’t scratch panel finish

• Won’t crack, dent or rust duringshipping or installation

• Won’t clog from airborne dust

• Prevents insect infiltration

• Prevents snow infiltration• Provides proven roof ventilation

• Meets all model building codes

• Packing in English, Frenchand Spanish

• No waste—use leftoverson next job

• Will not support a flame• Made in U.S.A.

Eagle Crest/Ameridrain®

5-V Panel

Ambler/Pro Panel II

Rydal/Channeldrain 2000®

3/4" Hi Rib

M/U Panel

Agri Panel

Devon/Delta Rib

2.67 Corrugated

Uni-Rib ™

Morton Hi Rib

Regal Rib®

Rugged Rib®

7/8" Wide Rib®

Perm-A-Clad®

DuroClad

Wayne/Spanline

R Panel

Multi Rib

Tile Sheet 25/1100

LS-28 Large Tab

Ultra Lock

AP Panel

Pro-S 12 Panel

Royal Lock ™ 12"

Royal Lock ™ 16"

SL-12®

SL-16®

1" x 5/16" x 12"*

1" x 5/16" x 16"*

Alu-Loc

Medallion Loc*

Metalogic 2000 (12")





SSR Panel 16"

SSR Panel 18"

Application

ProfileVentNew or re-roof on Purlinor wood deck Construction:Use a 2" opening at the r idge

to provide ventilation. On newor re-roof wood deck construction,cut a 2" slot at the ridge (1" each side,start cut 6" from gable ends).On purlin construction position panels

to leave a 2" opening.

Available in convenient sizes• 20' package

• 50' package

• 100' package

Current panel profiles

*No positioning glue.Note: The trademarks listed above are those of the respective roof panel manufacturers.

1Allow 2" opening at ridge forventilation. ProfileVent is rolled

out along the ridge, gable to gable,about 1" up-slope from the ridge capedge. The positioning adhesive onmost profiles will hold ProfileVent inposition and allow for repositioning.

3Screw down or pop rivet the ridgecap according to manufacturer’s

instructions (works with any ridge cap).2ProfileVent can be cut with

scissors or utility knife.

Inset: When splicing ProfileVent,make the splice at the center top of the high rib and use caulk or sealantalong the splice.



Ventco™ Ridge Cap Anchor Clip Ridge cap anchor clip



1Install your metal roofing panelaccording to manufacturer’s

instructions. Apply mastic above andbelow pre-drilled holes in the clip.Before installing ProfileVent®, insert #14A screw through the large down-slope access hole in top of the RidgeCap Anchor Clip.

Anchor clips are recommended in high wind areas and on panels with major ribs 16" on center or greater.

Anchor Clip Detail

2Lift the back end of clip. SlipProfileVent under the clip. Push

clip back down and insert another #14A screw in the up-slope hole.

Application

Ventco™ Ridge Cap Anchor ClipAn independent engineering corporation tested the performanceof the Ventco Ridge Cap Anchor Clip under high wind loading.During testing, a roof/ridge vent/cap system was subjected to wind

speeds that follow the Dade County Test protocol.

The following observations were made concerning theperformance and structural integrity of the clip and ridge cap:• No lift ing of the ridge cap up to 115 mph

• No fastener pull out or loosening

• The ridge cap remained in contact with ventilation system

• No difference in performance when the cap is secured to the clip with screws or rivets

Specifications• 20 gauge galvanized steel

• Visible surface painted black for aesthetic purposes

Packaging• 25 clips per small box

• 24 small boxes per master box

• 600 clips per master box

M9002

3/4" Anchor ClipM9004

1" Anchor ClipM9006

1-1/4" Anchor ClipM9008



2-1/2" Anchor Clip

OptionsNone

Anchor Clip U.S. Pat. 6418678 (other patents pending)



Weather Gard® Tools, Belted Fasteners and Accessories

Installation Screw Guns Installation screw guns and drive socketsInstallation tools


• Screw guns and noise pieces are matched for individual products to insure consistent installation performance.

• Screw gun manufactures and individual tools are tested andpre-qualified for reliable field performance beforerecommendation.

Application

DI 600 Power ScrewdriverFor installingself-drilling fastenersFeature: Versa clutch system

CF 50 Setting Nose PieceInstallation tool with depth

locator for long SX compositepanel fastenersFeatures:

ZA 1/4"/ 80 drive shaft

E 380 drive socket

irius® Drive SocketThe E-420 setting tool is requiredfor installing the irius drive systemThe fasteners are clamped firmlyvia the teeth under the fastener head

Hex and Torx® Drive Bits1/4" Hex one piece magnetic driveSize Part No.

1/4" Hex J0865

5/16" Hex J0875

3/8" Hex J0925

1/4" Torx one piece drive bitSize Part No.

6-Lobe, 2-3/4"-long drive bit J1990

Volts: 110Amps: 6.5

Speed: 0 – 2000 rpm variable speed

Socket E-420

E-420 parts kit

Spare jaws



Panelmaster™ Assembled belted fasteners



• Increased speed of installation• Improved working ergonomics• Stand-up roof attachment

• Fasteners installed uniformly every time• Special footpieces available for attachment through the panel rib• Installs fasteners 1"– 3" long

ApplicationPanelmaster™ Tool KitStandard tool kit includes:– Panelmaster tool

– DeWalt® 18V drive unit

– Battery charger and extra battery

– One extension piece

– Extra drive bits

– Corded DeWalt drive unit available

– One-year full replacement warranty

Belted Fasteners– SFS intec fasteners 1" through 3" lengths

with sealing washers

– Can be painted to match any panel color

– All fasteners packaged 500 per carton

Woodgrip™ Fasteners

Item Length SFS Part #Woodgrip 9 –15 HWHControl Seal WasherSentri Coated

1" C0161-CCBL

1-1/2" C0261-CCBL

2" C0381-CCBL

2-1/2" C0461-CCBL

3" C0485-CCBL

Woodgrip 9 –15 HWH.001" Mech ZincControl Seal WasherSentri Coated

1" C0167-CCBL

1-1/2" C0267-CCBL

2" C0382-CCBL

2-1/2" C0467-CCBL

3" C0487-CCBL

HiLo Woodgrip 10 –15HWH Bond Seal WasherSentri Coated

1" A1067-CDBL

1-1/2" A1072-CDBL2" A1077-CDBL

2-1/2" A1082-CDBL

3" A1087-CDBL

Woodgrip XG 12 –11 HWHBond Seal WasherSentri Coated

1" A1806-EMBL

1-1/2" A1841-EMBL

2" A1851-EMBL

2-1/2" A1856-EMBL

3" A1861-EMBL

Long-Life Fasteners

Item Length SFS Part #WoodZAC 9-15 HWHSeal Washer

1" C0165-DNBL

1-1/2" C0265-DNBL

2" C0385-DNBL

2-1/2" C0465-DNBL

3" C0481-DNBL

WoodMAC 9-15 HWHSeal Washer

1" C0168-CABL

1-1/2" C0268-CABL

2" C0388-CABL

2-1/2" C0468-CABL

3" C0488-CABL

Evergrip ™ 9-15 HWHStainless Bond Seal Washer

1" E4160-CUBL

1-1/2" E4260-CUBL2" E4380-CUBL

2-1/2" E4460-CUBL

Evergrip 9-15 TorxStainless Bond Seal Washer

1" 1110324

2" 1110327

3" 1110329

Selection




Blind Rivets — Grommet FastenersBlind rivets attach light gage

Grommet fasteners attach fiberglass panels


Blind rivets• Allow for one side attachment of light gage metal panels through a pre-drilled hole.• Available in steel and aluminum or stainless for applications requiring corrosion resistance performance.• Available pre-painted to color match the panel.

ApplicationBlind RivetsMaterials: Mandrel Rivet:Aluminum AluminumStainless Stainless

Material Size Part No. Grip Range Pre-Drill Hole Size

Aluminum AA4 3D L0520 .126 – .187 #30 (.129 – .133)Stainless STST43D L1290 .126 – .187 #30 (.129 – .133)

Grommet fasteners• Allow for one side attachment of fiberglass panels through a pre-drilled hole.• Designed to pull fiberglass panels together without cracking the material.• Come assembled with EPDM washers for a weather tight seal.

Application

Grommet FastenersMaterials:

Neoprene rubberw/ molded brass nut

Size 3/8" Grommet:Part No. E0260-CSFastener:10-32 x 1-1/4" stainless5/16" AF Hex Head

Washer:15 mm O.D stainless Bond Seal

Size 1/4" Grommet:Part No. E0080-CUFastener:

6-32 x 1-1/4" stainless1/4" AF Hex Head

Washer:12 mm O.D stainless Bond Seal


OptionsPainted

Stocking Colors:

001 White012 Blue014 Bright White020 Tan042 Burnish047 Green051 Dk. Gray109 Beige110 Brown228 Green232 Green248 Lt. Stone348 White578 Gray

850 Ash Gray890 Red



Weather Gard™ CoatingsWeather Gard


Threaded fasteners for roofing and siding systems are

available in a wide range of materials, designs, and

coatings. When specifying your fastener, be sure to

choose one that has a performance life equaling or

exceeding the life of the proposed project.

Fastener Materials

Common Fastener compositions:

• Zinc plated and paint coated carbon steel

• Alloy capped fasteners with zinc-aluminum,stainless steel, and nylon capped head designs

• Stainless Steel: 300 Series austenitic stainless steel

• Stainless Steel: 400 Series martensitic stainless steel

• Bi-metal: stainless head and threaded shank with a

joint welded hardened carbon steel drill or sharp point

Coated Corrosion-Resistant Fasteners

SFS intec offers various coating systems such as

electroplating, mechanical plating, Silver Sentri, ™ Color

Sentri and Chromagard ™ paint. Silver Sentri and Color

Sentri are plastic alloy coatings that SFS intec applies

as a barrier coating. Zinc serves as a sacrificial coating

to provide cut-edge plating protect ion.

Metal Alloy Capped Fasteners

ZAC® Zinc Aluminum Capped Head

ZAC design fasteners provide the corrosion resistance

of a zinc-aluminum alloy capped head on a hardened

steel fastener for sel f-drilling or self-tapping installation.

ZAC is the original capped zinc-aluminum head fastener

and is used in more metal buildings than any other

capped fastener.

ZAC design fasteners are available with a 5 /16" and

3/8" capped hex washer head in Impax ™ self-drilling

fasteners, Woodgrip ™ sheet-to-wood fasteners and

self-tapping screws.

MAC™ Stainless Capped Head Self-Drilling Fasteners

MAC stainless capped head design combines the

corrosion resistance of stainless steel and a hardened

steel fastener for self-drilling installation. MAC design

fasteners are available with a 5/16" capped hex washer

head in a wide selection of Woodgrips and Impax

self-drilling fasteners.

Prisma™ Nylon Head Self-Drilling

and Self-Tapping Fasteners

Prisma design fasteners combine the corrosion

resistance of a nylon-molded head with a hardened

steel fastener for self-drilling and self-tapping

installation. The nylon head is formulated with the color

built in. It naturally resists fading and will never rust

like steel headed fasteners. Prisma design fastenersare avail-able with 3/8 " and 7/16" hex washer heads in

self-drillers, Woodgrip metal-to-wood fasteners, and

self-tapping AB fasteners.

Fastener Design



Weather Gard

45SFS intec, Inc. | Weather Gard ™ Product Group | 1-800-234-4533 ©20 08 SFS intec, Inc.

Stainless Steel FastenersA commonly held belief that stainless steel will not rust

or corrode is not necessarily accurate. Stainless steel

is a generic term covering over 200 different t ypes

of alloys that, to varying degrees, corrode less than

carbon steel. It is important that a specifier be aware of

the panel and project performance expectations when

specifying stainless steel fasteners.

Several types of stainless steel are used for fasteners.

300 Series Stainless/Austenitic

• 18-8 stainless alloy with 18% chromium and 8% nickel

• Best known grades are 304 and 316, both work

hardened in the thread-rolling process to manufacture

a self-tapping fastener capable of tapping threads

into steel

• Can be manufactured as a self-drilling, bi-metal

fastener by incorporating a heat-treated hardened

carbon steel drill point joint welded to the austenitic

stainless fastener

• Nonmagnetic

• Provides excellent corrosion resistance compared tomartensitic 410SS fasteners and plated steel fasteners

• Austenitic stainless steel is considered the only type

of stainless steel for panel fasteners

410 Series Stainless/Martensitic

• Stainless alloy with 11.5% to 13.5% chromium

• Can be heat treated to provide hardness to

manufacture as self-tapping or self-drilling

fasteners (when hardened, the part has less

corrosion resistance)

• Poor corrosion resistance compared

to austenitic stainless

• Magnetic

• Plated to improve corrosion resistance

(like carbon steel fasteners)

• Martensitic stainless is not considered

suitable for panel fasteners

Bi-Metal Fasteners

SX Fastener: Austenitic Stainless Self-Drilling Fasteners

SX design fasteners combine the corrosion resistance

of an austenitic 300 series stainless head and threaded

shank with a hardened carbon steel point for self-

drilling installation. These bi-metal fasteners install

like carbon steel fasteners and provide the corrosion

resistance of 18-8 300 series austenitic stainless. SX

fasteners are true stainless steel self-drilling fasteners.

When selecting a stainless steel fastener for any

application where minimizing or virtually eliminating

corrosion is the goal, a specifier should strongly

consider the dramatically greater benefits of 3 00

series over 400 series stainless steel fasteners. The

richer chemical composition and required blade (SX)

or welded drill point make 300 series stainless steel

fasteners more costly, but the corrosion resistance

benefits are far superior.



Weather Gard


Washer design contributes to the weather seal of a

fastener. SFS offers several washer options based upon

the type of fastener and the applicat ion requirements.

Bonded Washer

• EPDM rubber bonded to metal

• Metal washers are available in galvanized

steel, aluminum, and stainless steel

• Bonded washers offer a low-profile appearance

• Provides positive weather seal between

panel and fastener head

Sealer Cupped Hex Washer Head

• EPDM rubber captured under integral

cupped hex head washer

• Cupped washer head prevents overdriving

• EPDM washer and cupped head offers

an excellent weather seal

• EPDM is protected from UV rays

by cupped washer head

Control Seal

• EPDM rubber captured under the stamped “dome”

• Available on all Woodgrip drill screws

• Reinforced domed shoulder distributes clamp load• EPDM sealant compressed in three key areas

• Weather tight seal even if fastener is driven

in on an angle*

Fastener Head Styles

SFS offers a wide variety of fastener head sty les

designed to meet your project and fastener

requirements. Each head style will provide proper

panel attachment and desired finish appearance.

Available fastener head sty les are:

• irius® drive, low profile

• HWH (hex washer head)

• Cupped hex washer head sealer

• Metal-alloy capped cupped:

HWH ZAC or HWH MAC

• Pancake head

*Proper installation techniques should always be employed.

Washer Styles



Weather Gard


Fastener and steel gauge sizes used throughout this Weather Gard section are nominal.

Fastener SizesFastener Size #10 #12 #14

Thread Diameter Decimal Equivalent .190 .216 .250

Steel Gauge Sizes*

Gauge 30 28 26 24 22 20 18 16 14 12 10

Decimal Equivalent .012 .015 .018 .024 .030 .036 .048 .060 .075 .105 .135* Standard steel thickness used for panels, purlins and girts.

Fasteners are designed to withstand a varied range

of types of loading. Each panel or structural system has

its own specific fastener loading requirements. Care

must be taken to ensure that the appropriate loading

requirements for each application are considered.

Typical structural performance criteria that influence

fastener design include:

Ultimate Tension Strength

The point at which a fastener fails under a load

exerted in two direct opposite directions.

Typical ultimate tension strengths of each fastener type

are provided on the fastener information pages.

Ultimate Torsion Strength

The point at which a fastener fails under a twisting

load exerted on the head during installation in

a torsional direction.

Typical ultimate torsion strengths of each fastener type

are provided on the fastener information pages.

Ultimate Shear StrengthThe point at which a fastener fails under

a load exerted in offset opposing directions,

usually upon the shank of the fastener.

Typical ultimate shear strengths of each

fastener type are provided on the fastener

information pages.

Pull-out Performance

The ability of a fastener’s threaded connection

to remain intact and resist tensile loads.

Self-tapping fasteners require that a pilot hole be

drilled prior to installation. The pullout resistance

will be directly related to the pilot hole diameter.

Self-drilling fasteners have been developed,

and are available, for most steel construction

applications, to a metal thickness of 1/2". This type

of fastener is manufactured with its own integral drill

point, which is engineered to drill the optimum hole

size to facilitate eff icient thread forming in the metal

structure, resulting in optimized pullout values.

Pull-over Performance

The ability of a fastener to resist the pulling of

the fastened sheet material over the head of the

fastener due to gravity, wind, or other load.

The resistance to pullover failure is related to the

strength and diameter of the fastener washer and

the strength and thickness of the metal panel.

Structural Performance



Weather Gard


Plating Definitions

Electroplating is a method of depositing zinc on the

surface of the part using an electrolytic at traction of

the zinc to the fastener. Electroplating deposits a dense

coating of zinc over the entire surface of the part.

The zinc plating is a sacrificial coating protecting the

base part from scratches or other coating breaks.

Mechanical plating is a method of depositing zinc

on the surface of the part using a hammering or impact

process. This method applies the zinc to the entire

surface of the part. Mechanical plating deposits a less

dense, but thicker coating of zinc over the surface

of the part. The zinc plating is a sacrificial coating

protecting the base part from scratches or other

coating breaks.

Sentri™ Corrosion Resistance Coating

Silver Sentri ™ and Color Sentri ™ are proprietary heat-

cured plastic alloy coatings that SFS intec applies

to the entire sur face of the plated steel fastener.

Chemically, Sentri is a metallic filled organic polymer

coating applied to fasteners by means of a dip/ spin/

cure process. Both Silver and Color Sentri are applied

in multiple coats to a prescribed finished film thickness.

Each coat is oven cured after application for maximum

adhesion and corrosion protection. Color Sentri isavailable in a variety of colors to match selected panel

colors. Fasteners with sealing washers are assembled

prior to coating so that all of the final assembly surfaces

are coated with the corrosion-resistant film.

Coatings

Sentri coating exceeds Factory Mutual 4470 corrosion-resistance standard.

Kesternich Accelerated Corrosion Testing

Below is a comparison of Silver Sentri coated fasteners, G-90 galvanized and Galvalume ® corrosion resistance

in Kesternich accelerated corrosion testing. Kesternich cabinet testing simulates acid rain conditions and is

used worldwide for accelerated corrosion testing.



HeadquartersSpring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610610-376-5751 Fax: 610-376-8551

Manufacturing Plants

Exeter Plant Lincoln Corporate Center, 41 Dennis DriveReading, PA 19606

Medina Plant 5201 Portside DriveMedina, OH 44256

Wyomissing Plant Spring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610

U.S. Service Centers

Reading Service Center Spring Street & Van Reed Road, PO Box 6326Wyomissing, PA 19610

Durant Service Center PO Box 576, 500 West Third AvenueDurant, IA 52747

Houston Service Center 6120 West by Northwest Boulevard, Unit 160

Houston, TX 77040

Atlanta Service Center 675 Progress Center AvenueUnit MLawrenceville, GA 30043

Sacramento Service Center 2426 Port StreetWest Sacramento, CA 95691

Contact Us Toll Free: 1-800-234-4533 Fax: 1-888-485-4225Visit our website at www.sfsintecusa.com

Weather Gard Fastening Systems

sfs weather gard may08

Documents