rheofinish 225 d

Upload: ajitpushpa

Post on 16-Oct-2015

50 views

Category:

Documents


3 download

DESCRIPTION

Formwork release agent

TRANSCRIPT

  • RHEOFINISH 225 DWater based chemical release agent

    DescriptionA ready to use water based, safe, effective releaseagent which is friendly to the environment.RHEOFINISH 225 D is applied to mould andshutter faces prior to casting concrete in order toachieve a clean release. After removal of theformwork, the resultant concrete has a smooth,hard, uniform finish, with reduced incidence ofblow holes. RHEOFINISH 225 D can be appliedto the formwork by spray in the form of a lightuniform mist coating.

    Primary usesRHEOFINISH 225 D is formulated for applicationto plywood, timber, steel and plastic facedformwork and moulds, prior to casting concrete,to ensure a clean release.

    PackagingRHEOFINISH 225 D is available in 20 and 210litre drums. Bulk deliveries available upon request.

    *Typical propertiesColour Milky liquidSG finished product 0.971 at 25CChloride content: Nil

    CompositionA chemically active release agent blended withwater.

    Directions for useApply before the first casting and thereafter re-apply immediately after stripping and cleaning themould.

    Lightweight horticultural sprayers are ideal asRHEOFINISH 225 D is finely atomised to give auniform coating. Excessive application should beavoided.Alternatively, application may be made by a finehaired brush, only a very thin coating should bemade and any excess removed.

    If after the first application, the RHEOFINISH 225D is completely absorbed into new timber orplywood, a further application should be madebefore filling the moulds or formwork.

    ActionRHEOFINISH 225 D reacts chemically withcement to impart excellent release properties totreated surfaces. Concrete cast against surfacescoated with RHEOFINISH 225 D exhibit asmooth, hard, uniform finish.

    RHEOFINISH 225 D has no negative effect onthe properties of concrete nor will it impair theadhesion of subsequent surface treatments whenapplied at the recommended coverage rates.

    CoverageThe coverage rate for RHEOFINISH 225 D isbetween 30 to 40m/litre when spray applieddepending on smoothness and porosity of theformwork used. Coverage is considerablyenhanced on marine ply and steel faced forms.

  • RHEOFINISH 225 D

    Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied withany recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the

    application are beyond our control.

    As all BASF technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.

    BASF Construction Chemicals UAE LLC

    P.O. Box 37127, Dubai, UAE

    Tel: +971 4 8090800 Fax: +971 4 8851002

    www.basf-cc.ae

    Note:Progressively better results are obtained onplywood and timber moulds as they becomeimpregnated and the operatives becomeaccustomed to working with the release agent.RHEOFINISH 225 D in general, may be used overtimber moulds etc., which have been treated withother mould oils, providing excess has beenremoved.

    Equipment careRHEOFINISH 225 D may usually be left in sprayguns or sprayers without detriment, but withcertain types, there may be some softening ofrubber seals with prolonged contact.

    StorageStore under cover, out of direct sunlight andprotect from extremes of temperature. Storagelife up to 1 year when stored in unopenedcontainers as above. The product must be stirredbefore being used.

    Failure to comply with the recommended storageconditions may result in premature deterioration ofthe product or packaging. For specific storageadvice consult BASF's Technical ServicesDepartment.

    Safety precautionsAs with all chemical products care should betaken during use and storage to avoid contactwith eyes and mouth. Treat splashes to eyes andskin immediately. If accidentally ingested, seekimmediate medical attention. Keep away fromchildren and animals. Reseal containers after use.

    NoteField service, where provided, does not constitutesupervisory responsibility. For additionalinformation contact your local BASFrepresentative.

    BASF reserves the right to have the true cause ofany difficulty determined by accepted testmethods.

    Quality and careAll products originating from BASFs Dubai, UAEfacility are manufactured under a managementsystem independently certified to conform to therequirements of the quality, environmental andoccupational health & safety standards ISO 9001,ISO 14001 and OHSAS 18001.

    01/2000 BASF_CC-UAE revised 11/2003

    * Properties listed are based on laboratory controlled tests.