radar automated test &measurement system (ats) · – automated test system (ats), meeting the...

1

RADAR Automated Test &Measurement System (ATS)

1. Introduction ISTRAC is responsible for the Design, Development, Integration, Testing and

commissioning of Radars required to cater the needs of ISRO as well as other national

requirements at X,C and S frequency bands. Characterisation of different subsystems and

system is essential during the development, system integration and system maintenance.

Radar Automated Test and Measurement System (ATS) is proposed for elaborate, accurate

and fast evaluation & qualification of subsystems and system to cater overall performance

specification of different radars.

ISTRAC has been using multiple bench top equipment like Signal Generators, Signal

Analysers, Network Analysers, Oscilloscopes etc. for testing various subsystems and

systems. ATS design with different test instruments and related Hardware & Software is

proposed here. The ATS should include all required test instruments for the characterization

of the Radars. ATS should be scalable, upgradeable and flexible in nature. The ATS should

also be of open architecture from a software perspective so that it can be automated or

integrated in any heterogeneous instruments and programming environment for the ease of

work and to improve test efficiency and timings.

Radar Automated Tests and Measurement System shall carry out the accurate system level

performance tests, measurements & calibrations and subsystem level functional and

performance tests including Antenna, Servo, Transmitter, Waveform Generator, RF Front-

end, RF/IF Receiver, Clock Generator, Digital Receiver and Signal Processor, Display &

Archival subsystems.

2. Guideline to Vendors: 2.1.Automated test System requirements for S, C & X-Band Radar Systems may be

combined in a single system.

2.2.Vendor shall develop common ATS control software and hardware to cater the

requirement for S, C and X-Band Radar.

2.3.Vendor shall develop ATS to cater requirement of individual subsystems &integrated

system level testing for S, C & X-Band Radar systems.

2.4.Only OEMs and OEM certified Authorised Dealers are required to submit the quote.

Certificate issued by OEMs should be provided along with the quote.

2

2.5.Vendor is required to quote for 5 years warranty and application support.

2.6.All Software Source codes and installation kit containing actual deliverable software

shall be provided.

2.7.All the ATS modules shall be of 19” Rack mountable unit, with necessary power,

cabling and any other additional accessories.

2.8.The ATS shall be deployed at different places of Radar. ATS shall be designed with

easy dismantling features and also suitable packing shall be provided for the purpose

of transportation and quick installation and integration.

2.9.ISTRAC shall evaluate the price bids of technically qualified vendors for deciding

lowest bidder (L-1) on the basis of ultimate landing cost including all the deliverables,

calibrations, soft wares and warranty as per TENDER.

2.10. L1 will be computed based on the total landing cost with five years warranty.

Extended warranty will execute after the completion of 5 years warranty at the

discretion of ISTRAC.

3. Scope of Work

Building, integrating (both hardware and software segments) and supplying integrated Radar

– Automated Test System (ATS), meeting the following requirements:

3.1.Shall be able to Test all subsystems sequentially as per the specifications. It shall be

possible to test even single subsystem independently.

3.2.Shall provide all the external interfaces needed by all the DUTs and control the

DUTs. Shall be able to power all or any one of the DUTs selectively. However,

measurements can be sequential.

3.3.All the test instruments, switch matrix and RF cables need to be calibrated

automatically by ATS and to be used before any measurements.

3.4.Shall be able to run through the complete test plan without any further manual

intervention, once the setup is made and calibration is done.

3.5.A single GUI software package shall be provided to carry out all test and evaluation

and calibration as listed in the document.

3.6.The software package shall have all flexibilities to configure the instruments to its

maximum and minimum specifications, formulate test cases etc. GUI also supports

self-calibration of instruments and generates the report.

3

3.7.The ATS software shall be implemented such that it is modular, easily amenable to

modifications/expansions without major change in the "core" of the software.

3.8.ATS software shall be able to process the measured data and shall be able to generate

plots, export the data to Microsoft Excel spread sheets or any spread sheet software,

e.g. open-office & PDF format with all the necessary annotations.

3.9.Integrated Automatic report generation for all tests shall be a part of the software.

3.10. Vector Network Analyzer

will be supplied by ISTRAC. The vendor shall integrate the

VNA supplied by ISTRAC into the ATS. The ATS software shall be capable of handling

VNA also. The overall ATS block diagram with Radar DUT is shown in Figure. 1.

3.11. The vendor shall carry out on-

site calibration of the equipments of the ATS as listed

in Table.1. The periodicity of calibration shall be as follows:

a) Once every six months

b) Whenever any equipment is found to be out of calibration.

Automated warning message shall be generated to alert the initiation of the calibration

process.

3.12. Detailed calibration, test and evaluation requirement is listed in the document.

The test instruments required and configuration requirement also listed. However,

there may be requirement of additional instruments or configuration to complete all

the calibration and testing listed in the document. It is the responsibility of the vendor

to identify such instrument or adding additional configuration while quoting the

tender and explain in detail. If any part of the test is unable to complete with the setup

projected by ISTRAC or the vendor modified configuration will lead into non-

compliance of deliverables.

3.13. Proper naming convention shall be defined to identify different radar systems

and subsystems.

3.14. ATS supply voltage: 230V ac , single phase, 50 Hz (nominal)

3.15. Vendor has to work out data backup plan on separate machine (workstation as

listed in Table.1) Automatic data transfer after each test set is required. It should have

feature of viewing test report from backup machine.

3.16. Modifications in the specifications and test plan, if any, will be intimated at

the time of PDR.

4

Fig.1 ATS Block Diagram for Radar DUT

3.17. Tests and Calibrations to be performed by the software application

Following are the list of Tests and Calibrations to be performed by ATS:

3.17.1. SSPA/Klystron/Magnetron Transmitter tests

(i) Power Output for Long, Medium, Short Pulses over BW

(ii) Interlocks and Status

(iii)Triggers/Timings/Controls

(iv) VSWR

(v) Rise time, fall time, pulse droop, pulse distortion

3.17.2. RF Front-end tests

(i) Gain, P1dB

5

(ii) Dynamic Range/Linearity, Sensitivity

(iii)Noise Figure

(iv) Bandwidth, Harmonics & Spurious

(v) Intermodulation Distortion

(vi) LO Spectral Purity, Image Rejection

3.17.3. IF Receiver tests

(i) Gain, P1dB

(ii) Dynamic Range/Linearity

(iii)Noise Figure

(iv) Bandwidth

(v) Harmonics & Spurious

(vi) Intermodulation Distortion, Image rejection

3.17.4. Antenna System RF Testing

(i) Antenna Gain

(ii) Radiation Pattern

(iii) Co-pol

(iv) Cross-pol

(v) Sidelobes

(vi) Radome loss

(vii) Beamwidth & Pointing Accuracy

3.17.5. Radar Waveform Generator

(i) Pulse measurements – rise time, fall time,

(ii) Spectrum – Harmonics, spurious

(iii) Phase Noise

3.17.6. Digital Receiver, DSP, Data Processor & Displays tests

(i) Power Level Sweep, Frequency Level Sweep

(ii) Pulsed RF measurements

(iii) Real Signal-to-Noise Ratio (SNR in dB)

(iv) Phase Noise Performance

(v) Wideband Noise Performance

(vi) Jitter and SNR Performance of the Signal generator as a Clock Source

(vii) Jitter Bandwidth

(viii) Distortion and Spurious

(ix) Signal-to-noise and distortion (SINAD in dB)

(x) Total harmonic distortion (THD in dBc)

(xi) Spurious-free dynamic range (SFDR)

6

(xii) Third-order input intercept point (IIP3 in dBm)

(xiii) Harmonics

(xiv) Non-Harmonics

3.17.7. Integrated Radar Testing

(i) Dynamic Range

(ii) Doppler Sweep

(iii)Multi carrier Dynamic and Doppler Sweep Tests.

3.18. Deliverables:

3.18.1. Hardware Deliverables of ATS: The vendor shall deliver the

instruments and hardware as listed in Table.1 for the RADAR Automated

Tests and Measurement System for S, C & X Band along with all Manuals.

Refer Annexure-1 for the detailed specifications of the instruments and the

hardware listed in the Table.1.

Table1: RADAR Automated Tests and Measurement System

Module (Test Instruments and Hardware) Qty (Nos)

1) Real Time Spectrum Analyzer (Detailed Specifications in Table 3) 1

2) Arbitrary Waveform Generator (Detailed Specifications in Table 4) 1

3) RF Signal Generators (Detailed Specifications in Table 5) 3

4) RF & Clock Signal Generator (Detailed Specifications in Table 6) 1

5) Mixed Signal Oscilloscope (Detailed Specifications in Table 7) 2

6) Arbitrary Function Generator (Detailed Specifications in Table 8) 2

7) RF Switch Matrix(Detailed Specifications in Table 9) 1

8) Workstation (Detailed Specifications in Table 10) 2

9) Laptop (Detailed Specifications in Table 11) 2

10) 10G Rack mount Ethernet LAN Switch (Detailed Specifications in

Table 12)

3

11) 19” Instrumentation Rack with required accessories (Detailed

Specifications in Table 13)

1

12) ATS Software Application for all the test cases 1

3.18.2. 18.2 Software Deliverables of ATS:

ATS Software Application shall be developed to carry out all the test cases mentioned

in point 17 Tests and Calibrations and shall have following requirements:

7

3.18.2.1. Documents: Vendor should provide Software Requirement Specification

(SRS), Software Design Document (SDD), User manual for software and offer

them for review.

3.18.2.2. All Software Source Code and Installation Kit containing actual deliverable

software shall be provided.

3.18.2.3. Code walk-through is to be conducted by ISTRAC team along with vendor

at the time of ATP.

3.18.2.4. Software Audit to be conducted by ISTRAC team before final delivery.

3.18.2.5. The vendor shall ensure continued support for the supplied software

including the Operating system on which the application resides for a period

of at least five years from the date of acceptance.

3.18.2.6. ATS Software applications should have the following quality attributes:

a) Security: Login and password facility with user registration and password

recovery mechanism. All important configuration files and code files should

be protected with separate administrative password. Session time out facility.

b) Software should be maintainable which includes modification, corrections,

improvements or adaptation of the software to changes in environment. To

achieve this modularity of software is compulsory along with version control

feature.

c) GUI of ATS shall have following features: display- preferably: User id and

DUT, Instrument connectivity status, Input parameters entry, Test result and

test condition selection, Test result status, Test completion time and error

message display. GUI shall be elegant and user friendly with all settings

through user editable configuration files.

4. Requirement Specification Review & Preliminary Design Review

Vendor shall prepare system requirement document including Hardware and Software

requirements within 3 weeks after the confirmation of the order. This document shall we

reviewed and vetted by ISTRAC team before PDR.

Vendor shall conduct a Preliminary Design Review (PDR) approximately 6 weeks after

confirmation of order. PDR will consist of design/configuration (block diagram), Interface

details, Software Design etc., of ATS. Acceptance Test Plan (ATP) shall be prepared by

vendor in consultation with RDA, ISTRAC.

8

4.1.Factory Acceptance Testing (FAT)

Upon completion of the ATS development, vendor shall demonstrate the compliance of

functional requirements and measurement accuracy/ precision specifications as per mutually

agreed Acceptance Test Plan (ATP) including software. ISTRAC/ ISRO representative may

witness the Pre-shipment Clearance Testing at manufacturer’s premises. Shipment clearance

will be given after successful completion of FAT.

4.2.Site Acceptance Test (SAT)

Vendor is responsible for installation and commissioning of the Radar Automated Test

System (ATS) at ISTRAC, Bangalore or at a place in India, as suggested by ISTRAC. Upon

completion of the installation and commissioning of ATS at site, vendor shall demonstrate

the compliance of functional requirements and measurement accuracy/ precision

specifications as mentioned in ATP. ISTRAC Engineer(s) shall be witnessing the acceptance

testing at the time of ATP. The ATS will be accepted after the successful completion of the

ATP cleared by ISTRAC/ISRO Committee.

5. Training Once the system is installed and operational, training shall be held. System Engineer familiar

with the hardware, software and test methodologies shall conduct this training. The training

shall focus on familiarization with the instrumentation, test methodologies, programming and

operational usage of the ATS.

6. On Site Application Support Vendor shall provide application support for 5 years after acceptance of the system. System

Engineer familiar with the hardware, software and test methodologies used shall be available

to deliver this support. This support shall immediately follow the system installation and

training.

In case of any failure in ATS, vendor shall respond to ISTRAC within2 days (48 hrs.)with

respect to the request sent by ISTRAC. After that vendor has to correct the fault within 4

days (96 hours).

9

7. Warranty, Support and Calibration ATS shall have 5 years of warranty. If 5 years warranty is not available as standard, vendor

shall quote for standard warranty plus chargeable warranty for remaining term. If equipments

are to be sent for calibration/repair, pickup and delivery from site of installation shall be done

by vendor only at no additional costs.

8. Payment terms & conditions along with delivery schedule Payment terms: Vendor shall specify payment terms and conditions.

Delivery Schedule:

Table-2 Delivery Schedule

System Requirements Specification

(SRS) Review

3 Weeks after confirmation of order by vendor

Preliminary Design Review (PDR) 6 Weeks after confirmation of order by vendor

Factory Acceptance Testing (FAT) 20 weeks after confirmation of order by vendor

Site Acceptance Testing (SAT) 22 weeks after confirmation of order by vendor

Note: ISTRAC will provide DUTs for SAT.

9. Documentation For ATS, vendor shall produce custom system documentation and compile it into a System

Reference Manual. This shall include

Operating manual for the ATS.

Comprehensive Service manual for maintaining the complete system

ATS Calibration data and procedure.

Custom System Reference Documentation shall include rack layout, system interconnect

diagrams, serialized instrument/equipment and other hardware list, custom cable pin out

tables and certificates as applicable. The documents shall be supplied in electronic form.

10. Additional Guideline to vendors 10.1. The vendor shall examine the whole RFP thoroughly and offer point by point

compliance matrix indicating clearly the parameter/specification in tabular format for

their offer. In case of non-compliance, the deviation from the specified parameter

shall be furnished.

10.2. Vendor must quote for all the points mentioned in RPF. All the test cases (Section

3 Scope of Work, point 17) are necessary for offer consideration.

10.3. Vendor shall quote in two parts :

10

a. Part 1: Technical offer along with masked price-bid

b. Part 2: Commercial offer

10.4. Vendor can attach additional information if any, which may provide more

information on ATS.

10.5. The delivery schedule shall be presented in a bar chart form showing sequence and

time of all important activities e.g. ATS development, testing etc.( including design

reviews etc.)

11

Annexure-1

Detailed Specifications of ATS Items

11.Real Time Spectrum Analyzer

Table: 3 Technical Specifications for Real Time Spectrum Analyzer

S. No. Parameter Specifications

11.1. Architecture Real time Spectrum analyzer

11.2. Frequency Range 10 Hz to 12 GHz or better

11.3. Real-time acquisition bandwidth 150 MHzor better

11.4. Aging Rate Better than 1 x 10-7

/year

11.5.

Displayed Average Noise Level

(Without Preamp) Better than –140dBm/Hz at 12 GHz

11.6.

Displayed Average Noise Level

(With Preamp) Better than –150dBm/Hz at 12 GHz

11.7. Harmonic Distortion Better than –65dBc at 12 GHz

11.8. Spectrum Length Upto 32K points

11.9. Selectivity Better than 5:1

11.10. Spurious Free Dynamic Range Better than70dBc

11.11. Trigger Modes Free Run, Single Triggered

11.12. Trigger Types Power, Frequency, Time

11.13. Detectors ±Peak, Average (VRMS), Sample

11.14. Pulse Measurements Pulse Trace, Pulse Table

11.15.

Phase Noise & Jitter

Measurements

Should support Phase Noise as well as Jitter

Measurement

-130dBc @10KHz offset @1GHz

11.16.

Noise Figure and Gain

Should support Noise Figure and Gain

Measurement with following specification

or better

Gain Range: -10 to 30 dB

Noise figure Range: 0 to 30 dB

Resolution : 0.01dB

Noise figure measurement error : ±0.1dB

Gain measurement error : ±0.1dB

12

11.17. Display LCD/LED Display

11.18. Interfaces LAN, USB

11.19. Operating Temperature Range 0 °C to 55 °C

11.20. Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%

11.21. Rack Mountable accessories To be provided

11.22. Warranty

Quote for 5 Years of Warranty with periodic

calibration.

11.23. Operating and service Manual

Soft and Hard copy of manual needs to be

provided.

11.24.

All necessary connectors and

adapters are to be provided by

the vendor to carry out the

required test.

11.25.

Calibration Kit & Calibration

certificate to be provided.

12. Arbitrary Waveform Generator

Table:4 Technical Specifications for Arbitrary Waveform Generator

S.No. Parameter Specifications

12.1. Number of Channels 2 Analog Channels

12.2. Frequency Output 10 GHz or better

12.3. Analog Bandwidth 10 GHz or better

12.4. Rise Time 25ps or better

12.5. DAC Sampling rate 20 GS/s or better

12.6. Vertical Resolution 8 Bits or better

12.7. Waveform Memory 1 GSamples on both channels or better

12.8. Spurious Free Dynamic Range - 40 dBc or better

12.9. Flatness Parameter Better than ± 2 dB

12.10.

Triggering & Run Modes Continuous, Triggered and Triggered

Continuous & Individual sequences can

be run on each channel

12.11. Interface LAN, USB

13

12.12. Display Characteristics LCD/LED display

12.13.

Radar Generation Capabilities

(IQ, IF&RF Waveforms)

1) Modulation types, viz. FM Chirp,

NLFM, FM Step, User-defined Step FM

2) Define all Pulse Parameters including

Start Time, Rise Time, Off Time, Fall

Time, Pulse Width, and impairments like

Droop, Overshoot, and Ripple

3) Define a Staggered PRI with Ramp,

User-defined Profiles and Multipath

4) Ability to generate IQ impairments

like I/O imbalance, Quadrature error,

carrier Leakage

12.14. Operating Temp. Range 0 °C to 40 °C



12.17.

Warranty Quote for 5 Years of Warranty with

periodic calibration.

12.18.

Operating and service Manual Soft and Hard copy of manual needs to

be provided.

12.19.




required test.

12.20.


certificate to be provided.

13. RF Signal Generator

Table:5 Technical Specifications for RF Signal Generator

S. No. Parameter Specifications

13.1. Frequency Range: 100 kHz to 12.75 GHz

13.2. Frequency Resolution 0.001 Hz

13.3. Frequency error < 1 × 10–7

13.4. Reference Frequency 10MHz (internal and external)

14

13.5. Reference oscillator OCXO

13.6.

Power Level range (above 1

MHz)

–140 dBm to +15 dBm or better

13.7. Power Level Resolution 0.01 dB

13.8.

Maximum permissible reverse

power

0.5W

13.9. Harmonics < –30 dBc

13.10.

SSB phase noise @ 10GHz

(1Hz bandwidth), carrier offset

20KHz

<-97dBc

13.11.

Frequency sweep Trigger mode

Digital mode with free run, full sweep,

execute one step, external trigger, internal

trigger

13.12. Trigger source

external trigger, remote control, internal

trigger

13.13. Sweep range full frequency range

13.14. Sweep shape triangle, sawtooth

13.15. Step spacing linear

13.16. Power level sweep

digital sweep in discrete steps with 0.01 dB

resolution

13.17. Trigger mode

free run, full sweep, execute one step,

external trigger, internal trigger

13.18.

Trigger source for power and

frequency sweep

external connector, remote control

13.19.

Trigger slope for power and

frequency sweep

(with external trigger) positive, negative

13.20. Power Sweep shape triangle, sawtooth

13.21. Step spacing logarithmic

13.22.

Dwell time setting range for

power and frequency sweep

10 ms to 10 s

13.23.

Modulation Type

Amplitude modulation, Frequency

modulation, Phase modulation, Pulse

modulation, Pulse generator, Pulse train with

internal and external modulation source.

13.24. Pulse modulation On/off ratio > 80 dB

15

13.25.

Minimum width for pulse

modulation

20 ns

13.26.

Repetition frequency for pulse

modulation

0 Hz to 10 MHz

13.27. Pulse generator mode single pulse, double pulse

13.28. Pulse generator Trigger modes

free run, internally triggered, externally

triggered, externally gated

13.29. Pulse period setting range 40ns to 40s

13.30.

Pulse period , pulse width

&Pulse delay setting resolution

10 ns

13.31. Pulse width setting range 20 ns to 1 s

13.32.

Pulse delay setting range (with

external trigger)

10 ns to 1 s

13.33.

Double-pulse spacing setting

range

20 ns to 1 s

13.34. Pulse Train : Trigger modes automatic (free run),externally triggered

13.35. Number of pulses in pulse train 1 to 2047

13.36.

Pulse width and pulse spacing

setting range in pulse train

20 ns to 5ms

13.37.

Pulse width and pulse spacing

setting resolution in pulse train

10 ns

13.38. Remote control Interface Ethernet/LAN (VISA interface), USB




13.42. Warranty


calibration.

13.43.

Operating and service Manual Soft and Hard copy of manual needs to be

provided.

13.44.




required test.

13.45.


certificate to be provided..

16

14. RF &CLOCK Signal Generator

Table: 11. Technical Specifications for RF & CLOCK Signal Generator


14.1.

ADC Characterization

Should support latest ADC, DACs like AD9208

Dual 3 Gsps 14b A/D converter, AD9172 Dual

12Gsps 16b D/A converter

14.2. Frequency Range Better than 12 GHz

14.3. Resolution of setting 0.001 Hz

14.4. Frequency error < 1 × 10–7

; Aging: ≤ 3 × 10–8

/year

14.5. Reference Frequency 10MHz (internal and external)

14.6. Power Level Setting range –120 dBm to +18 dBm

14.7. Maximum permissible reverse power 10W or higher with reverse power protection

14.8. Harmonics ( f = 12GHz) < -55 dBc @ 10dBm

14.9.

SSB phase noise CW, standard

performance, carrier offset 20kHz CW,

measurement bandwidth 1 Hz, level =

10 dBm

< -115dBc (1GHz to 10GHz carrier)

14.10.

Modulation Type

Amplitude modulation, Frequency modulation,

Phase modulation, Pulse modulation, Pulse

generator, Pulse train with internal and external

modulation source.

14.11. Pulse modulation On/off ratio > 80 dB

14.12. Minimum width for pulse modulation <20 ns

14.13. Pulse generator modes single pulse, double pulse

14.14. Pulse generator Trigger modes

free run, internally triggered, externally triggered,

externally gated

14.15.

Multifunction generator - Frequency

Range

Sine : 0.1 Hz to 10 MHz; pulse, triangle, trapezoid

: 0.01 Hz to 1 MHz

14.16.

Multifunction generator - noise

bandwidth

100 kHz to 10 MHz

14.17. Signal Types - LF Generator 1 sine, pulse, triangle, trapezoid

14.18. Signal Types - LF Generator 2 sine, pulse, triangle, trapezoid

17

14.19.

Noise generator (noise amplitude

distribution)

Gaussian, equal

14.20. Resolution Sine : 0.01Hz; pulse, triangle, trapezoid : 10 ns

14.21. noise bandwidth 100kHz

14.22.

Internal Differential Clock Synthesizer

up to 6GHz

14.23. Clock Signal Generation

differential square wave, differential sine wave,

single-ended sine wave, differential CMOS

14.24. Frequency range 10MHz to 6GHz

14.25. Resolution 0.001Hz

14.26. Level Setting Range

–24 dBm to 20dBm (sine wave, differential and

single-ended) 0.8 V to 2.7 V (differential CMOS)

14.27. Remote control Interface Ethernet/LAN (VISA interface), USB, serial


14.29. Power Requirement

230V ± 10%, Freque

ncy: 50 Hz ± 3%


14.31. Warranty


calibration.

14.32.

Operating and service Manual Soft and Hard copy of manual needs to be

provided.

14.33.

All necessary connectors and adapters

are to be provided by the vendor to carry

out the required test.

14.34.

Calibration Kit & Calibration certificate

to be provided.

15. Mixed Signal Oscilloscope

Table: 6.Technical Specifications for Mixed Signal Oscilloscope


15.1. No of Analog input channels 4

15.2. No of Digital input channels 16

15.3. Bandwidth 500 MHz

18

15.4. ADC Resolution 10 bits or better

15.5. Sample Rate

5 GS/s or better on all analog channels&

2 GS/s or better on all digital channels

15.6. Record Length

62.5 Mpoints or better on all analog &

digital channels

15.7. Acquisition Modes Sample, Peak detect

15.8. Analog input coupling Both DC and AC

15.9. Analog Input impedance 50 Ω and 1 MΩ

15.10.

Maximum input Analog

voltage

50 Ω: 5 VRMS, with peaks ≤ ±20 V

1 MΩ: 300 VRMS, CAT II

15.11.

Minimum detectable pulse

width

5 ns or better

15.12. Trigger modes Auto, Normal, and Single

15.13. Cursor types

Waveform, V Bars, H Bars, and V&H

Bars

15.14.

Amplitude measurements

Amplitude, Maximum, Minimum, Peak-

to-Peak, Positive Overshoot, Negative

Overshoot, Mean, RMS, AC RMS, Top,

Base, and Area

15.15.

Timing measurements

Period, Frequency, Unit Interval, Data

Rate, Positive Pulse Width, Negative

Pulse Width, Skew, Delay, Rise Time,

Fall Time, Phase, Rising Slew Rate,

Falling Slew Rate, Burst Width, Positive

Duty Cycle, Negative Duty Cycle

15.16. Display type 14 inch or better

15.17. External reference input external 10 MHz reference

15.18. Interfaces USB, Ethernet

15.19. Probes Analog and Digital Logic Probes




15.23. Warranty

Quote for 5 Years of Warranty with

periodic calibration.

15.24. Operating and service Soft and Hard copy of manual needs to

19

Manual be provided.

15.25.


adapters are to be provided

by the vendor to carry out

the required test.

15.26.

Calibration Kit &

Calibration certificate to be

provided.

16. Arbitrary Function Generator

Table: 7. Technical Specifications for Arbitrary/Function Generator

S.No. Specifications

16.1. No. of channels : Two

16.2.

Waveforms : Sine, Square, Pulse, Ramp, Triangle, sinc, Gaussian, Noise,

arbitrary waveforms & more type of waveforms will be preferable

16.3.

(i) Sine Wave: 1 microHz to 240 MHz or better, Burst Mode :1 microHz

to120 MHz or better

(ii) Square Wave : 1 microHz to 120 MHz or better , Rise/Fall time< 3 ns

(iii) Pulse Wave : 1 mHz to 120 MHz or better ,pulse width 5.00 ns to

900 s or better, pulse duty 0.001% to 99%,Overshoot <5%

(iv) Arbitrary Waveforms : 1 mHz to 120 MHz or better, Vertical

resolution 14 bits, Rise/Fall time <= 3 ns ,Memory: 128 K

samples & Sample rate 250 MS/s or better

16.4. Modulation : AM, FM, PM, FSK, PWM

16.5. Phase noise at 20 MHz, 10 kHz offset : < -100 dBc/Hz or better

16.6. Harmonic Distortion : < -50 dBc or better

16.7. Amplitude, 50 ohm Load : 50 mVp-p to 4 Vp-p

16.8.

Auxiliary Inputs: 10 MHz Reference Input , Trigger input.

Auxiliary Outputs: Trigger Output,10 MHz Reference Out Remote

Programming interface :USB and LAN

Main Output impedance: 50 ohm , Connector: BNC(F)

16.9.

Power supply input:

230V ± 10%, Frequency: 50 Hz ± 3%(Indian power plug & power cord)

20

17. RF Switch Matrix

Table: 8. Technical Specifications for RF Switch Matrix

16.10. Operating Temperature Range: 0 °C to 55 °C

16.11. Rack Mountable accessories to be provided

16.12. Warranty : Quote for 5 Years of Warranty with periodic calibration.

16.13.

Operating and service Manual: Soft and Hard copy of manual needs to be

provided.

16.14.

All necessary connectors and adapters are to be provided by the vendor to

carry out the required test.

16.15. Calibration Kit & Calibration certificate to be provided.

Switch Matrix Specifications

17.1. Frequency 10 MHz to 15 GHz

17.2. Insertion Loss 1 dB or Better

17.3. Isolation 90 dB or Better

17.4. VSWR at input port 1.3:1

17.5. Switching speed ~15ms

17.6. Impedance 50 Ohm

17.7. Life cycle ~5million

17.8. Communication Controller with LAN interface

17.9. Driving Module

proper driving module Should be

provided

17.10. power handling 1W Avg & 50 W peak

17.11. power supply 220 to 240 V AC

17.12.

Switch matrix configuration

6x6 switch matrix -2 Nosto interface all

instruments and DUT

17.13. Attenuator(0-90 dB 10dB step) 4 Nos

17.14. Attenuator(0-70 dB 10dB step) 4Nos

17.15. Attenuator(0-10 dB 1dB step) 4Nos

17.16. Terminators 50 Ohm 20 Nos

17.17. PDC(1:4) 4 Nos

17.18. PDC(1:2) 4 Nos

21

18. Workstation

Table: 9. Technical Specifications for Workstation

S.No Features Specification

18.1 Make and Model Mandatory to Provide Make & Model

18.2 Details of Product

Specifications website

and URL (web

address) link

Mandatory to provide Product Specifications

website and its URL link

18.3 Processor

2 Nos. of Intel Xeon Silver 4116 Processor 2.1 GHz

or better

18.4 Chipset Intel C622

18.5 RAM 64 GB ECC, DDR4, 2400 MHz memory

18.6 Internal Storage 2 Nos of 1TB SSD Hard Disk

18.7 Optical Drive Internal DVD RW

18.8 Graphics Card

NVIDIA 8GB Graphics Card or better shall be

delivered.

18.9

Network

a) Integrated Dual Port one Gigabit Ethernet

b) Dual Port 10 GbE T- RJ 45 Port Card, down

gradable to 1G Support.

18.10

Key Board

Standard Wired USB Keyboard. The offered

workstation and Keyboard shall be from same

OEM. 18.11

Mouse

Standard Optical USB mouse with 3 button one

scroll wheel. The offered workstation and mouse

shall be from same OEM.

18.12

Power Supply

Power - Power supply with 80% or better efficiency,

Power Supply rating: 220 volt/50 Hz shall be

delivered 18.13

Ports Ports – Front :2 USB, Rear: 4 USB, Audio in, out

and Microphone shall be delivered

18.14

Chassis

Workstation tower model, Completely tool less

chassis with handles in front and rear side. Rack

mountable accessories to be provided

18.15 Certification RoHS, WEEE, EPEAT Gold – ENERGY STAR.

18.16 Operating System

Windows 10 Professional 64 bit with One Year

Standard support shall be delivered

18.17 Software

Microsoft Office Suite with service pack – Latest

version

18.18 Warranty 5 years Onsite Warranty

18.19

Monitor

The supplied workstation and monitor shall be from

same OEM.

Vendor shall deliver required video cables /

convertors along with the monitor. All cables and

convertors shall be OEM certified hardware

22

Supplied Monitors shall have following

specification or better

27-inch IPS LED Monitor or Better.

Panel Type/ Surface: LED backlight, antiglare,

Widescreen Flat Panel Display

Aspect Ratio: 16:9

Viewing angle: 178° horizontal; 178° vertical

Brightness: 300 cd/m2 or better

Contrast Ratio: 1000:1 static; 8000000:1 dynamic

Power Supply rating: 220 volt/50 Hz.

Interface: Compatible with the offered workstation

model suitable to drive dual display configuration.

18.20

Installation &

Commissioning

Vendor should install & commission the systems as

per the configuration at RDA, ISTRAC Bangalore.

System installation, commissioning is the sole

responsibility of the vendor. It includes the

installation of all hardware, operating system, all

necessary device drivers and system libraries.

At the time of installation and commissioning of the

configuration, if it is found that some additional

hardware accessories or software items with

licenses are required to complete the configuration

to meet the operational requirement of the

configuration which were not included in the

vendor's original list of deliverables, then vendor is

required to supply such items to ensure the

completeness of the configuration at no extra cost to

ISTRAC. Vendor should ensure completeness of the

list of deliverables in the offer to avoid such

discovery during installation.

Vendor should resolve all issues related to

compatibility of hardware, drivers, and other system

software with OS.

18.21

Notes to the Vendor

The offered product shall be from a reputed OEM

who owns such product line for at least for last five

years.

Vendor shall submit following certifications from

OEM on OEM’s letter head.

The vendor is authorized for participating in the bid.

The offered workstation hardware is not an obsolete

product.

The offered hardware / software component is back

to back supported by the OEM during the warranty

period.

For all items in the list of deliverables offered by the

vendor, the manufacturer's part number should be

clearly indicated. Offer of items without clear

specification of part number is not acceptable.

23

19. Laptop Table: 10. Technical Specifications for Laptop

Sl.

No Parameter specifications

19.1 Make and Model Mandatory to Provide Make & Model

19.2 Processor 8th Generation Intel® Core™ i7 processor, Quad

Core or better

19.3 Operating System Windows 10 Professional 64 bit OS

19.4 Memory 16GB DDR4 or Better

19.5 Hard Drive 1TB SSD Hard drive

19.6 Display 14 to 16 inch FHD or Better

19.7 Video NVIDIA 2GB DDR3 or Better

19.8 Ports 3 USB3.0 or Better

19.9 Network 10/100/1000 Ethernet

19.10 Battery 3 Cell 48 WHr battery or Better

19.11 Bluetooth& WLAN Should Support

19.12 Mouse Cordless mouse

19.13 DVD Writer External USB slim DVD +/- RW Optical Drive

19.14 Accessories 1TB USB based SSD

19.15 Accessories Laptop leather bag with cushioned compartment

with additional compartments for peripherals

19.16 Software Microsoft Office Suite with service pack – Latest

version

19.17 power pack External power pack

19.18 Adapter AC Adapter

19.19 Warranty 5 Years

19.20 Power Requirement 230V ± 10%, Frequency: 50 Hz ± 3%

19.21 Notes to the Vendor

The offered product shall be from a reputed OEM

who owns such product line for at least for last five

years.

Vendor shall submit following certifications from

OEM on OEM’s letter head.

The vendor is authorized for

participating in the bid.

The offered workstation hardware

is not an obsolete product.

The offered hardware / software

component is back to back supported by the OEM

during the warranty period.

24

20. 10G Rack mount Ethernet LAN switch

Table: 12. Technical Specifications for 10G Rack mount Ethernet LAN switch

Sl No: Parameter Specification

20.1. Item 10 G Ethernet Switch

20.2. I/O ports and slots 12 or more RJ45 1G/10GBASE–T ports

2 SFPs or more

20.3. SFP module Switch should be loaded with 2 Nos. of 10G SR

transceivers in multi-mode fiber.

20.4. Multi-mode fiber patch

cords

3 Nos. should be included

20.5. memory 512 MB RAM or better

256 MB FLASH or better

20.6. Packet buffer size 2 MB or better

20.7. processor Cortex-A9 @ 1.25MHz or better frequency

20.8. latency Less than 5uS

20.9. Throughput/packet

forwarding rate

238 Mpps or better for 64 byte packet size

20.10. Routing/Switching

capacity

320 Gbps

20.11. Routing table size 500 entries or better

20.12. MAC address table size 16000 entries or better

20.13. MTBF 30 years or better

20.14. Switching & routing Layer -2 switching & Layer -3 static routing

20.15. IPv4 static routing & IPv6

static routing

Support IPv4 & IPv6 static routing

20.16. Access Control Lists

(ACLs)

Layer –L2/Layer –L3

20.17. Mounting scheme Rack mounting

20.18. Warranty 5 Years

20.19. Cat 6 A Patch Cords 25mtr – 6Nos, 10mtr-5nos, 5 Mts-10Nos.

20.20. Management Should be Manageable

20.21. Operating Temperature

Range 0 °C to 55 °C

25

21. 19” Instrumentation Rack

Table: 13. Technical Specifications for 19” Instrumentation Rack

S.No. Specifications

21.1

Height 42U

Width 600 mm

Depth 800 mm

21.2 Static load-carrying capacity 400 kg

21.3 Type of protection IP 55

21.4 Shielding up to 50 dB at 1 GHz, 40 dB at 3 GHz (tested to IEC 61587-3)

21.5 Fan top cover cooling with minimum 4 fans

21.6 Perforated base plate with cable ducting

21.7

Welded basic frame with conductive seal all-around, Front door, rear door,

side panel

21.8 GND/earthing kit to be provided

21.9 Adjustable foot & Raised top cover

21.10 Power supply distribution

AC supply 230V ,50Hz (Indian power plug & power cord)

21.11 Any other additional accessories

21.12 Operating Temperature Range: 0 °C to 55 °C

21.13 Warranty: 5 Years


20.23. Rack Mountable

accessories To be provided

20.24. Operating and service

Manual Soft and Hard copy of manual needs to be provided.

20.25. Vendor should install & commission the systems as per the configuration at RDA,

ISTRAC Bangalore.

20.26. Vendor should provide technical brochure and Compliance statement for the given

Specifications

26

22. GENERAL REQUIREMENTS FOR INSTRUMENTS

(TECHNICAL LITERATURE SHALL BE SUPPLIED, WHEREVER APPLICABLE)

22.1. Vendor should quote for only new equipment (No quote will be accepted for refurbished or used

equipment)

22.2 Vendor should quote for all required hardware/software/calibration standards required to meet all

the above specifications.

a. All the specifications offered by vendor shall be guaranteed specifications referenced to

instrument’s published technical data sheet.

b. If any specification is specified as typical value only, in vendor data sheet then vendor must

certify separately that the delivered instrument will comply with the tender specification at the

time of installation/commissioning.

c. In case, both, guaranteed as well as typical specs are given in data sheet, then only guaranteed

specs will be considered. Typical specs will be ignored.

22.3 Vendor should indicate the quoted equipment model and accessories parts numbers in support for

each specification in tabular form

22.4 All parts/ accessories should have operating power: 220 to 240V AC, 50 Hz. All necessary power

cords with Indian (3-pin plug) type to be provided by vendor.

22.5 Only OEM or their authorized representative for India shall quote with authorization certificate.

22.6 Operational, programming and service manual (Electronic form) must be provided with the

instrument.

22.7

For technical evaluation of the bids, if required by ISTRAC, the vendor may be asked to give

demonstration of the instrument functionality at RDA/ISTRAC, Bangalore of the quoted model

with all the options and accessories required to meet the tender specifications.