proel ms32 manual

8/18/2019 Proel MS32 Manual

1/57

PROELMS 32

PROGRAMMABLEMIDI SENDER

OWNER’S

MANUAL


2/57

2 Proel MS 32 Owner's Manual

INDEXSPECIFICATIONS....................................................................................................................... 3

MEMORY STRUCTURE ............................................................................................................ 4

MS 32 FRONT AND REAR VIEW ............................................................................................. 5

POWER ON.................................................................................................................................. 6

GLOBAL PARAMETERS........................................................................................................... 7POWER-ON NAME : ..............................................................................................................................................7

POWER-ON SET & PATCH RECALL : .................................................................................................................8BASIC RX MIDI CHANNEL : ................................................................................................................................9

FOOT CONTROLLER 1 CALIBRATION :........................................................................................................... 10FOOT CONTROLLER 2 CALIBRATION :........................................................................................................... 11CONTINUE SWITCH ASSIGNMENT:................................................................................................................. 12GLOBAL PARAMETERS FLOW CHART : .........................................................................................................13WRITE GLOBAL PARAMETER:.........................................................................................................................14

MODE......................................................................................................................................... 15

SET MODE................................................................................................................................. 16SET SELECTION (0~9): .......................................................................................................................................16START/STOP AND CONTINUE FUNCTIONS:................................................................................................... 17

NOTE:...................................................................................................................................................................17SET NAME : ........................................................................................................................................................19SONG SELECT :................................................................................................................................................... 20

"A" PART TX MIDI CHANNEL : .........................................................................................................................21"B" PART TX MIDI CHANNEL : .........................................................................................................................22SET PARAMETERS FLOW CHART:...................................................................................................................23

WRITE SET MEMORY: .......................................................................................................................................24

PATCH MODE........................................................................................................................... 250~9 PATCH SELECTION: ....................................................................................................................................25START/STOP AND CONTINUE FUNCTIONS: ..................................................................................................26EDIT PATCH PARAMETERS: .............................................................................................................................27

FC1 ASSIGN :........................................................................................................... ............................................28FC1 RANGE : .......................................................................................................................................................29FC2 ASSIGN :.......................................................................................................... .............................................30

FC2 RANGE : .......................................................................................................................................................31FC 1/2 LINK :........................................................................................................................................................32

PATCH BAY SWITCH 1-2 : .................................................................................................................................33PATCH BAY SWITCH 3-4 : .................................................................................................................................34A CHANNEL BANK SELECT CC00 & CC32 : ....................................................................................................35A CHANNEL PROGRAM CHANGE :.................................................................... ..............................................36

A CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :............................................................................37A CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :............................................................................38B CHANNEL BANK SELECT CC00 & CC32 : ....................................................................................................39

B CHANNEL PROGRAM CHANGE : ..................................................................................................................40B CHANNEL PROGRAMMABLE "x" CONTROL CHANGE : ............................................................................ 41B CHANNEL PROGRAMMABLE "y" CONTROL CHANGE : ............................................................................ 42

PATCH PARAMETERS FLOW CHART: .............................................................................................................43WRITE PATCH MEMORY:..................................................................................................................................44

FACTORY RESET & MIDI DATA DUMP.............................................................................. 45FACTORY RESET:...............................................................................................................................................46DATA MIDI DUMP (sending):..............................................................................................................................47

DATA MIDI DUMP (receiving): ...........................................................................................................................48

FREE MODE.............................................................................................................................. 49MESSAGE SELECTION.......................................................................................................................................49THE POSSIBLE MIDI MESSAGES:.....................................................................................................................50MIDI MESSAGE TRANSMISSION:............................ .........................................................................................52

MIDI CHANNEL/ PATCH BAY SWITCHES .......................................................................................................53

FACTORY SETUP & RANGE.................................................................................................. 54GLOBAL PARAMETERS.....................................................................................................................................54SET PARAMETERS .............................................................................................................................................54PATCH PARAMETERS.......................................................................................................................................54

TECHNICAL SPECIFICATIONS ............................................................................................ 55SPARE PARTS & OPTIONALS ............................................................................................... 56


3/57

Proel MS 32 Owner's Manual 3

SPECIFICATIONS Rear Panel I/O & switch :

MIDI In

MIDI Out with Phantom Power

MIDI Thru

Foot Controller 1 In (FC 1 In)

Foot Controller 2 In (FC 2 In

Patch Bay Switch 1 Out (PBS 1 Out)




DC In

16 Switches, 3 Led

Display :

LCD 16 x 1

Mode :

Free

Patch

Set

Memory structure : (1 global, 10 sets, 100 patches)

Global parameter:1. Power On 10 characters name

2. Power On Set and Patch Number

3. RX Basic Midi Channel for Set and Patch recall Program Changes

4. Foot Controller 1 min/max calibrate

5. Foot Controller 2 min/max calibrate

6. Continue switch assign

10 Setseach containing:

1. 10 characters name

2. Song select to be sent (0~127/Off)

3. "A" part Midi Channel (1~16)

4. "B" part Midi Channel (1~16)

5. 10 Patches to be recalled

100 Patches10 for each Set containing 2 parts (A,B) midi data:1. FC 1 assign to CC (0~120 on channel A/B,AB, Off with min and max value)

2. FC 2 assign to CC (0~120 on channel A/B AB, Off with min and max value)

3.

FC1/2 link (On/Off)4. PBS 1-2-3-4 closed or opened (On/Off)

5. "A"- CC 00 (0~127/Off)

6. "A"- CC 32 (0~127/Off)

7. "A"- PC (1~128/Off)

8. "A"- xCC (0~120 at value 0~127/Off)

9. "A"- yCC (0~120 at value 0~127/Off)

10. "B"- CC 00 (0~127/Off)

11. "B"- CC 32 (0~127/Off)

12. "B"- PC (1~128/Off)

13. "B"- xCC (0~120 at value 0~127/Off)

14. "B"- yCC (0~120 at value 0~127/Off


4/57


MEMORY STRUCTURE

SET 0

SET 1

SET 9

Set name

Song select

"A" Midi Channel

"B" Midi Channel

10 Patches

"0~127/Off"

PATCH 0

PATCH 1

PATCH 9

"A"-CC 00

"A"-CC 32

"A"-PC

"A"- xCC

"A"- yCC

"SET NAME"

"0~127/Off"

"0~127/Off"

"1~128/Off"

"0~120"

"0~127/Off"

"0~120"

"0~120,A/B,AB

"0~127 (16 values) "

"On/Off"

"On/Off"

SET PARAMETERS

PATCH PARAMETERS

"0~9,0~9"

"1~16/Off"

"POWER-ON NAME"

GLOBAL PARAMETERS

"1~16"

"1~16"

"B"-CC 00

"B"-CC 32

"B"-PC

"B"- xCC

"B"- yCC

FC1

FC2

PBS1

PBS2

PBS3 PBS4

"127~0 (16 values)"

"0~120,A/B,AB

"0~127 (16 values) "

"127~0 (16 values)"

"1~128/Off"

"0~120"

"0~127/Off"

"0~120"

"0~127/Off"

"0~127/Off"

"On/Off"

"On/Off"

"min/max calibrate"

"min/max calibrate"

"Cnt,PBS,Cnt+PBS"

"on/off"

"0~127/Off" "0~127/Off"


5/57


MS 32 FRONT AND REAR VIEW

D C I N 9 V

F C 2

F C 1

P B4 P B 3 P B2 P B1

T HR U

O UT

I N

L C D C O NT RA S T

MI DI


6/57


POWER ON

When switched on the MS32 displays 3 subsequent screen shots before displaying the MASTER

screen shot;

first screen shot:

second screen shot:

third screen shot:

MASTER screen shot in the Patch mode:

PROEL MIDISender

MS-32 User Name

00 Basic Ch = 16

0 *FACTORY0* >0


7/57


GLOBAL PARAMETERS

- 10 characters name,

- SET and PATCH numbers displayed at power on

- the midi Basic channel and

- the calibrations for the Foot Controllers 1 and 2

- the assignment of the CONTINUE switch can be programmed as follows:

Power on the MS32 by keeping the "SELECT/CHANNEL" switch pressed; as soon as the stored

name is displayed, release the "SELECT/CHANNEL" switch;

POWER-ON NAME :

The "10 " and "10 " switches (

)

allow you to choose the character to beinserted.

(Keeping the switch pressed the characters

will shift automatically).

Use the " 5" and "6 " switches (

)

***User Name ***

Character Cursor

***User Name ***


8/57


Press and release:

- the "CCXXX/CONTINUE" switch (

) to confirm the data and pass to thedisplay/modification of the following "GLOBAL" parameter or

- the "SELECT/CHANNEL" switch (

) to confirm the data and exit from "GLOBAL" parameter

programming.

POWER-ON SET & PATCH RECALL :

Press the "10 " and "10 " switches (

)to choose the value (from 0 to 9) to be

inserted. (Keeping the switch pressed the

characters will shift automatically).


)

to move the cursor from SET to PATCH.

SET 0 & PATCH 0

SET 0 & PATCH 0

Value Cursor


9/57


Press and release:





programming.

BASIC RX MIDI CHANNEL :

Press the "10

" and "10

" switches (

)to choose the value (from 1 to 16 or AL =

Omni On) to be inserted and the On/Off

condition. (Keeping the switch pressed the

characters will shift automatically).


)

to move the cursor from channel number to

On/Off

Basic RxCh 16 On

Basic RxCh 16 On

Value Cursor


10/57


Press and release:





programming.

FOOT CONTROLLER 1 CALIBRATION :

FC1 mn -- Mx --

Position the Foot Pedal inserted in the FC1

socket at minimum value and press the

START/STOP switch;

Position the Foot Pedal at maximum valueand press the START/STOP switch (

).

OK is displayed twice on the screen.

FC1 mn Ok Mx Ok


11/57


Press and release:





programming.

FOOT CONTROLLER 2 CALIBRATION :

FC2 mn -- Mx --

Position the Foot Pedal inserted in the FC2

socket at minimum value and press theSTART/STOP switch;

Position the Foot Pedal at maximum value

and press the START/STOP (

) switch.

OK is displayed twice on the screen.

FC2 mn Ok Mx Ok


12/57


Press and release:





programming.

CONTINUE SWITCH ASSIGNMENT:

Continue=Cnt

Press the "10 " and "10 " switches ( )to select the Cnt (Continue), PBS (Patch

Bay Switches) or Cnt+PBS options.

Continue=Cnt

Value


13/57


GLOBAL PARAMETERS FLOW CHART :

"SELECT/CHANNEL" Switch

"CC XX/CONTINUE" Switch

POWER-ONNAME

POWER-ON

SET & PATCHRECALL

BASIC

RX MIDICHANNEL

FC 1CALIBRATION

FC 2CALIBRATION

EXIT

GLOBALPARAMETER

CONTINUESWITCH ASSIGN


14/57


WRITE GLOBAL PARAMETER:

Press and release the "SELECT/CHANNEL" switch (

) to confirm the data and exit from

"GLOBAL" parameter programming; the display will show the following message:

When using the WRITE switch the display will show the following message:

and will go back to the PATCH MASTER screen shot after some seconds:

WriteGlobal? W/S

Keep the WRITE/MODE switch (

)

pressed to store the GLOBAL parameters.

Press the START/STOP switch (

) toexit without storing the GLOBAL

parameters; the data of the previous

parameters will be lost.

WriteGlobal? W/S

Write Complete !

0 *FACTORY0* >0


15/57


MODE

When turned on, the MS32 is set in the PATCH mode.

Press and release the MODE/WRITE switch (

) to select one of the three operating modes of the

foot pedal as shown in the corresponding LEDs placed beside the display:

-

PATCH- FREE

- SET

Keep the MODE/WRITE switch pressed for some seconds to enter the functions WRITE SET or

WRITE PATCH.


16/57


SET MODE

In the SET mode it is possible to:

- recall the 10 SETS stored in the pedalboard using the switches from 0 to 9

- recall the 10 SETS stored in the pedalboard using the switches " "

- activate START/STOP and CONTINUE functions

- edit the SET parameters using the SELECT/CHANNEL" switch

SET SELECTION (0~9):

The pedalboard is in the SET mode when the SET LED is on, the cursor is under the SET Number

and the arrow points the SET Number.

When pressing one of the switches from 0 to 9 or one of the switches " ", the left side of the

display shows the SET number recalled and the 10 characters name associated to it.

All the set parameters are recalled :-

Song from 0 to 127/Off (midi message F3 00~7F)

- “A” part Midi Channel setting (from 1 to 16)

- “B” part Midi Channel setting (from 1 to 16)

- the stored PATCH of the new recalled SET is automatically selected

- all the recalled Set and Patch parameters are transmitted via Midi

Example:

press the switch no. 6 once or the " " switch six times, the display will show:

Note: The pedalboard allows you to recall alternatively two different sets using only one switch;

to recall alternatively the sets no. 3 and 7 press:

- the switch no. 3

- the switch no. 7

The pedalboard will now recall alternatively the sets no. 3 and 7 by pressing only switch no 7.

6


17/57


START/STOP AND CONTINUE FUNCTIONS:

When the switch START/STOP is pressed once, the START "FA" Midi message is sent to a

computer or a module sequencer connected via Midi to start a song; the display will show an "s".

If the switch START/STOP is pressed again, the STOP "FC" Midi message is sent to the equipment

connected to stop the song and the "s" is no longer displayed.

Pressing the "CONTINUE" switch while the pedalboard is in its "STOP" condition, the

CONTINUE "FB" Midi message is sent to play again the song from the previous stop position; the

display shows once again an "s".

Note: The CONTINUE function is linked to the Global "Continue switch assign" parameter.

To operate as CONTINUE control, the "Continue switch assign" parameter must beset in CNT or in PBS+CNT (cfr. page 11)

The CONTINUE switch can also operate only as PATCH BAY (PBS) selector if the

Global "Continue switch assign" parameter is set in PBS.The "s" symbol is no longer displayed when the CONTINUE switch is kept pressed.

(cfr. page 33/34)

NOTE:

Remember to set in LOCAL (INTERNAL CLOCK, REMOTE CONTROL, etc.) all theequipments (computer, module sequencer, etc.) connected via Midi to the MS 32 if you want to

control the START/STOP/CONTINUE functions from the pedalboard (note that no MIDI CLOCK signal is sent via midi from the MS-32).

0


18/57


EDIT SET PARAMETERS

When the pedalboard is in the SET mode press the "SELECT/CHANNEL" switch to edit theparameters of the selected "SET".

The display shows:

Press and release:

-

the "CCXXX/CONTINUE" switch (

) to confirm the data and pass to thedisplay/modification of the first "SET" parameter or


) to exit from "SET" parameter programming.

EDIT

Edit S continue?

Edit S continue?

Name: *FACTORY0*


19/57


SET NAME :

Press and release:


) to confirm the data and pass to the

display/modification of the following "SET" parameter or


) to confirm the data and exit from "SET" parameter

programming.


)

to select the character to be inserted.(Keeping the switch pressed the characters



)

to move the cursor.

Name: *FACTORY0*

Value Cursor

Song Sel: 0 Of


20/57


SONG SELECT :

Press and release:



display/modification of the following "SET" parameter or- the "SELECT/CHANNEL" switch (


programming.

Press the "10 " e "10 " switches (

) tochoose the value from 0 to 127 and On/Of

to be inserted.(Keeping the switch pressed the characters


Press the " 5" and "6 " switches (

)

to move the cursor from Song number to

On/Off

Song Sel: 0 Of

Value Cursor

A PartMIDI Ch 1


21/57


"A" PART TX MIDI CHANNEL :

Press and release:



display/modification of the following "SET" parameter or- the "SELECT/CHANNEL" switch (


programming.


)

to select a value from 1 to 16.(Keeping the switch pressed the characters


A PartMIDI Ch 1

Value

B PartMIDI Ch 2


22/57


"B" PART TX MIDI CHANNEL :

Press and release:


) to confirm the data and go back to the

display/modification of the first "SET" parameter or- the "SELECT/CHANNEL" switch (


programming.

Press the "10 " and "10 " switches ( )

to select a value from 1 to 16.(Keeping the switch pressed the characters


B PartMIDI Ch 2

Value

Name: *FACTORY0*


23/57


SET PARAMETERS FLOW CHART:

SETNAME

SONGSELECT

"A" PART

TX MIDICHANNEL

"B" PART

TX MIDICHANNEL

EXIT

SETPARAMETER

"SELECT/CHANNEL" switch

"CC XXX/CONTINUE" switch


24/57


WRITE SET MEMORY:

When keeping the " MODE/WRITE" switch (

) pressed for some seconds

or

in Edit mode : pressing and releasing the "SELECT/CHANNEL" switch (

) to confirm the

data and exit from "SET" parameters programming

the following message will be displayed:

When using the WRITE switch, the display will show the following message:

and will go back to the SET MASTER screen shot after some seconds:


)

to select a SET from 0 to 9 where to store

the inserted parameters. (Keeping the

switch pressed the characters will shift

automatically).

Keeping the WRITE/MODE switch (

)

pressed the displayed SET is stored.


) to

exit without saving the SET. All the data

of the previously modified parameters are

lost.

WrteSet 0 ? W/S

WrteSet 0 ? W/S

Exit (no write)WriteSet Number

Write Complete !


25/57


PATCH MODE

In the PATCH mode it is possible to:

- recall the 10 PATCHES of the current SET stored using the switches from 0 to 9

- recall the 10 SETS stored using the " " switches

- activate the START/STOP and the CONTINUE functions

- edit the PATCH parameters using the "SELECT/CHANNEL" switch

0~9 PATCH SELECTION:

When the PATCH LED is on, the cursor is under the PATCH number and an arrow points the

PATCH number, the MS32 is in its PATCH selection mode.

Pressing one of the switches from 0 to 9 the display will show, on the right side of the screen, the

PATCH number of the current SET.

All the patch parameters are recalled and transmitted via Midi:

Example:

when the switch no. 3 is pressed, the display will show:

0 *FACTORY0* >3

SET Number SET Name PATCH Number

EDIT 0~9 PATCH SELECTION START/STOP

0~9 SET SELECTION

START/STOP


26/57


If the " " or " " switches are pressed it is possible to select a different patch SET.

Example: the currently recalled patch no. 3 belongs to the set no. 0.

The pedalboard has 10 Sets, numbered from 0 to 9 and each set includes 10

patches.

It is therefore possible to recall the patches no. 0-3, 1-3, 2-3…9-3, each of themwith different parameters.

Note: The MS-32 allows you to recall alternatively two patches by using only one switch; forexample, to recall alternatively the patches no. 3 e 7 press:

- switch no. 3

- switch no. 7

The pedalboard will now recall alternatively the two patches, 3 and 7, when pressing only

the switch no. 7.

START/STOP AND CONTINUE FUNCTIONS:

If the switch START/STOP is pressed once, the START "FA" Midi message is sent to a computer

or a module sequencer connected via Midi to start a song; the display will show an "s".

When the switch START/STOP is pressed again, the STOP "FC" Midi message is sent to the

equipment connected to stop the song; the "s" is no longer displayed.

Pressing the "CONTINUE" switch while the pedalboard is in its "STOP" condition, the

CONTINUE "FB" Midi message is sent to play the song from the previous stop position; the

display shows once again an "s".

Note: The CONTINUE function is linked to the Global "Continue switch assign" parameter.

To operate as CONTINUE control, the "Continue switch assign" parameter must be

set in CNT or in PBS+CNT (cfr. page 11)

The CONTINUE switch can also operate only as PATCH BAY (PBS) selector if the

Global "Continue switch assign" parameter is set in PBS.The "s" symbol is no longer displayed when the CONTINUE switch is kept pressed.

(cfr. page 33/34)

NOTE:

Remember to set in LOCAL (INTERNAL CLOCK, REMOTE CONTROL, etc.) all the

equipments (computer,module sequencer, etc.) connected via Midi to the MS 32 if you want to

control the START/STOP/CONTINUE functions from the pedalboard (note that no MIDI

CLOCK signal is sent via midi from the MS-32).

0 *FACTORY0* s>3

START or CONTINUE selected


27/57


EDIT PATCH PARAMETERS:

When the pedalboard is in the PATCH mode, press the "SELECT/CHANNEL" switch to edit the

parameters of the selected PATCH.

The display will show:

Press and release:


) to display or modify the first “PATCH” parameter or


) to exit from “PATCH” parameter programming.

EDIT

Edit P continue?

Edit P continue?

FC1 to 7 AB On


28/57


FC1 ASSIGN :

Press and release:


) to confirm the data and display/modify the following

“PATCH” parameter or- the "SELECT/CHANNEL" switch (

) to confirm the data and exit from “PATCH” parameter

programming.

FC1 mn 0 Mx127


)

to select a Control Change value, from 0 to

120, the A/B/AB channel, and the On/Off

conditions.(Keeping the switch pressed the characterswill shift automatically).


)

to move the cursor back and forward.

FC1 to 7 AB On

Value Cursor


29/57


FC1 RANGE :

Press and release:- the "CCXXX/CONTINUE" switch (




programming.

FC2 to 11 AB On

Use the "10 " and "10 " switches (

)

to select a value from 0 to 127 to be

inserted as minimum and maximum pedalvalues.(Keeping the switch pressed the characters



)


FC1 mn 0 Mx127

Value Cursor


30/57


FC2 ASSIGN :

Press and release:


) to confirm the data and display/modify the following“PATCH” parameter or


) to confirm the data and exit from “PATCH” parameterprogramming.

FC2 mn 0 Mx127

FC2 to 11 AB On

Value Cursor


)

to select a Control Change value from 0 to

120, the A/B/AB channel, and the On/Off

position.(Keeping the switch pressed the characterswill shift automatically).


)



31/57


FC2 RANGE :





programming.

FC1/2 Link Of

FC2 mn 0 Mx127

Value Cursor

Press the "10 " and "10 " (

) to select

a value from 0 to 127 to be inserted as

minimum and maximum pedal values.(Keeping the switch pressed the characterswill shift automatically).


)



32/57


FC 1/2 LINK :



“PATCH” parameter or



programming.


)

to select the On/Off value of the Link

between the Foot Controllers 1 and 2.

When the Link is On each Foot Controller

transmits the parameters of both.

FC1/2 Link Of

Value

PBS1 Of PBS2 Of


33/57


PATCH BAY SWITCH 1-2 :

Note: The Patch bays stored in the ON condition can be rapidly activated and deactivated

when out of the EDIT mode by pressing the Continue switch.

The Patch Bay Switch function is linked to the Global "Continue switch assign"

parameter.

To operate as Patch Bay Switch (PBS) control, the "Continue switch assign"parameter must be set in PBS or in PBS+CNT (cfr. page 11)

Press and release:

-

the "CCXXX/CONTINUE" switch (

) to confirm the data and display/modify the following"PATCH" parameter or- the "SELECT/CHANNEL" switch (

) to confirm the data and exit from "PATCH" parameter

programming.

PBS3 Of PBS4 Of

PBS1 Of PBS2 Of

Value Cursor


)to select the On/Off condition to be

inserted for the patch bay switches 1 and 2.


)



34/57


PATCH BAY SWITCH 3-4 :

Note: The Patch bays stored in the On condition can be rapidly activated and deactivated

when out of the EDIT mode by pressing the Continue switch.

The Patch Bay Switch function is linked to the Global "Continue switch assign"

parameter.

To operate as PBS control, the "Continue switch assign" parameter must be set inPBS or in PBS+CNT (cfr. page 11)

Press and release:

-

the "CCXXX/CONTINUE" switch ( ) to confirm the data and display/modify the following"PATCH" parameter or



programming.

A c0= Of c32= 0f

PBS3 Of PBS4 Of

Value Cursor


)to choose the On/Off condition to be

inserted for the patch bay switches 3 and 4.

Use the " 5" e "6 " switches (

) to

move the cursor back and forward.


35/57


A CHANNEL BANK SELECT CC00 & CC32 :

Press and release:


) to confirm the data and display/modify the following"PATCH" parameter or


) to confirm the data and exit from "PATCH" parameterprogramming.

A PC = Of

A c0= Of c32= 0f

Value Cursor


)

to select a value from 0 to 27, and the Off condition to be inserted for the A Midi

channel CC00 and CC32.


)



36/57


A CHANNEL PROGRAM CHANGE :

Press and release:



"PATCH" parameter or- the "SELECT/CHANNEL" switch (


programming.

A xCC 91 = 40

A PC = Of

Value

Press the "10 " and "10 " switches ( )

to select a value from 1 to 128 and the Off

condition to be inserted for the A channel

program change midi message.


37/57


A CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :

Press and release:





A yCC 93 = 0

A xCC 91 = 40

Value Cursor


)

to select a value from 0 to 120 and 0 to

127, in the Off condition, to be inserted,

respectively, as the type and the value of A channel control change.


)



38/57


A CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :

Press and release:





B c0= Of c32= 0f

A yCC 93 = 0

Value Cursor


)



respectively, as the type and the value of A channel control change.


)



39/57


B CHANNEL BANK SELECT CC00 & CC32 :

Press and release:





B PC = Of

B c0= Of c32= 0f

Value Cursor


)


condition to be inserted for the B channel

CC00 and CC32.


)



40/57


B CHANNEL PROGRAM CHANGE :

Press and release:

- the "CC XXX/CONTINUE" switch (


"PATCH" parameter or- the "SELECT/CHANNEL" switch (


programming.

B xCC 91 = 40

B PC = Of

Value


)


condition to be inserted for the B channel

program change.


41/57


B CHANNEL PROGRAMMABLE "x" CONTROL CHANGE :

Press and release:





B yCC 93 = 0

B xCC 91 = 40

Value Cursor


)



respectively, as the type and the value of B channel control change.


)



42/57


B CHANNEL PROGRAMMABLE "y" CONTROL CHANGE :

Press and release:


) to confirm the data and go back to thedisplay/modification of the first "PATCH" parameter or



FC1 to 7 AB On

B yCC 93 = 0

Value Cursor


)



respectively, as the type and the value of B channel control change.


)



43/57


PATCH PARAMETERS FLOW CHART:

FC 1 ASSIGN

FC 1 RANGE

"SELECT/CHANNEL" Switch

"CC XXX/CONTINUE" Switch

FC 2 ASSIGN

FC 2 RANGE

PBS 1 & PBS 2

PBS 3 & PBS 4

A CC0 & CC32

A Program Change

A xControl Change

A yControl Change

B CC0 & CC32

B Program Change

B xControl Change

B yControl Change

EXIT PATCHPARAMETER

FC 1/2 LINK


44/57


WRITE PATCH MEMORY:

When keeping the " MODE/WRITE" switch (

) pressed for some seconds

or

in Edit mode : pressing and releasing the "SELECT/CHANNEL" switch (

) to confirm the

data and exit from "PATCH" parameters programming

the following message will be displayed:

When using the WRITE switch, the display will show:

and after some seconds will go back to the PATCH MASTER screen shot:

Write Complete !

WrtPtch 0-0? W/S


)

to choose the SET and one of the "0~9"

switches (

) to select a Patch (from 0-0to 9-9) where to store the inserted

parameters.

Keeping the WRITE/MODE switch (

)

pressed, the currently displayed PATCH is

stored.


) to exit

without storing the SET. The data of the

previously modified parameters will be

lost.

Patch Number

WrtPtch 0-0? W/S

Exit (no write)

Write

Set Number

0 *FACTORY0* >0


45/57


FACTORY RESET & MIDI DATA DUMP

The MS-32 pedalboard is provided with the following functions:

- FACTORY RESET to restore the original parameters set by the manufacturers.

- MIDI DATA DUMP (transmission) to download the memory parameters via Midi on a

connected Sequencer or Computer.

-

MIDI DATA DUMP (reception) to reload via Midi the memory parameters previously saved in a

connected Sequencer o Computer.

When powered-on through the " MODE/WRITE" switch, the display of the pedalboard shows the

following screen shot; release then the " MODE/WRITE" switch;

WrtPtch 0-0? W/S

Factory Reset

or

Data Midi Dump

Press the "0" or "9" switches (

) to select,

respectively, Factory Reset or Data Midi

Dump functions.


) to

exit from the Factory/Dump screen shot

and go back to the main menu.

Exit

0-Factory 9-Dump


46/57


FACTORY RESET:

Pressing and releasing the "0" switch, the display will show:

Press and release:

-

the "CC XXX/CONTINUE" switch (

) to reset the pedalboard with all the Factory parameters;

all the parameters of the GLOBAL, SET and PATCH memories are removed and reset at

"factory" value.- the "START/STOP" switch (

) to exit from the "FACTORY" function.

- If the Continue switch is pressed, the pedalboard will display:

and go back to the main screen shots.

- Press Start/Stop to exit from the "FACTORY" function; the pedalboard will display the main

screen shots.

Reset Continue?

Reset Continue?

Loading Factory!


47/57


DATA MIDI DUMP (sending):

Pressing and releasing the "9" switch, the display will show:

Press and release:

- the "CCXXX/CONTINUE" switch ( ) to start dumping the selected data (All, Global, Set, or

Patch) through the Midi Out (downloadable on a Sequencer or Computer)- the "START/STOP" switch (

) to exit from the "DUMP" function.

- If the Continue switch is pressed, the pedalboard will show:

When the data transmission is completed, the display will go back to the main screen shots..

Dump All Cont?

Dump All Cont?

Value


)to select the data to be inserted: All (all the

data), Glb (only the Global memory), Set

(only the 10 Set memories), Ptc (only the

100 Patch memories)

Dump All Cont?

Sending Dump.. !


48/57


DATA MIDI DUMP (receiving):

If a Data Midi Dump exclusive system is received (the same system generated by the pedalboard

when the Data Midi Dump is transmitting) via Sequencer or Computer, the MS-32 enters the Data

Midi Dump mode and will display the following screen shot:

alternating with the display of the different memories received.

- The pedalboard memories are thus loaded with the received Midi data, previously saved throughthe DATA MIDI DUMP (transmission) procedure.

Note : It is important not to accelerate the DATA DUMP procedure as the pedalboard needs

time to edit the data in the Flash memory.

If there is a reception problem or an error in the data loading, it is advisable to slow

down the dump procedure in the connected computer or sequencer.

- If the pedalboard is switched off during this procedure, incomplete data might be received.

When the data receiving is completed the pedalboard stops on the last memory received ordisplays:

This means the data reception was not successfully completed; it is necessary to switch thepedalboard off and activate the Factory Reset functioned described at pages 45/46.Retry the loading procedure controlling the dump speed and slowing it down if necessary.

Receiving Dump.!

Rx Dump Error..!


49/57


50/57


THE POSSIBLE MIDI MESSAGES:

CCXX switch

CC00 switch

CC32 switch

PC 0~127 switch

PC 1~128 switch

CC 07 switch

CC 10 switch

CC YY switch

CC 11 switch

CC 16 switch

Ch = 1 CC 16= 0

Ch = 1 CC 11= 0

CC 0 Continue? Ch = 1 CC 0= 0

Ch = 1 CC 10= 0

Ch = 1 CC 07= 0

Ch = 1 PC128= 0

Ch = 1 PC127= 0

Ch = 1 CC 32= 0

Ch = 1 CC 00= 0

CC 0 Continue? Ch = 1 CC 0= 0


51/57


CC 91 switch

CC 93 switch

CC 94 switch

SONG switch

Ch = 1 Song = 0

Ch = 1 CC 94= 0

Ch = 1 CC 93= 0

Ch = 1 CC 91= 0


52/57


MIDI MESSAGE TRANSMISSION:

When CC XXX and CC YYY are selected the display shows:

After selecting the type of Control Change to be sent using the " ", " " and "0~9" switches,

press the Continue switch (in this case "Start / stop" and "Continue" do not operate), the display

shows:

It is now possible to select the value to be sent through the above-described procedure.

NOTE : In the FREE mode the Foot Controllers 1 and 2 send the values of the selected midi

messages.

CC 0 Continue?

Ch = 1 CC 0= 0

Ch= 1 CC 07= 0Press the "10 " and "10 " switches (

)

to select the first and the second digit of

the value to be sent; use the switches from"0" to "9" (

) to select the unit of thethree-digit number and confirm the Midi

message transmission.

Press the Start/Stop and Continue switches

to activate the Start(FA), Stop (FC) e

continue (FB) messages. (cfr. page 22)

Value Value START/STOPCONTINUE


53/57


MIDI CHANNEL/ PATCH BAY SWITCHES

In the "FREE" mode it is possible to select the Midi channel where to send the messages and enterthe PATCH BAY SWITCHES section to activate the 4 On/Off:

.

MIDI CHANNEL/PATCH BAY SELECTION

Keep the "SELECT/CHANNEL" switch pressed for some seconds to select the midi channel and

the patch Bay

The display shows:

Press the " " and " " switches to select the Midi channel.

Press the "SELECT/CHANNEL" switch again to exit and go back to the FREE mode.

Press the "Continue" switch to display the PATCH BAY SWITCHES:

Press the switches from 1 to 4 to select alternatively the On or Off condition for the correspondingPATCH BAY switches.

Press the "SELECT/CHANNEL" switch to exit and go back to the FREE mode.

1on 2on 3on 4on

Ch= 1 Continue ?

Ch= 1 Continue ?

Channel


54/57


FACTORY SETUP & RANGE

GLOBAL PARAMETERS

FACTORY VALUE RANGE

"POWER-ON NAME" User Name ASCII

"0~9,0~9" 0-0 0~9-0~9

"1~16/Off" 16 On 1~16 On/Of "min/max calibrate" 30-97 0~126-1~127

"min/max calibrate" 30-97 0~126-1~127

SET PARAMETERS

FACTORY VALUE RANGE "SET NAME" FACTORY ASCII

"1~16" 1 1~16

"1~16" 2 1~16

"0~127/Off" 0 Of 0~127 On/Of

PATCH PARAMETERS

FACTORY VALUE RANGE "0~120,A/B,AB Of" 07 AB On 0~120 A/B/AB On/Of

"0~127 (16 values) " 00,8,16,24,32,40,48,

56,64,72,80,88,96,104,112,120,127

"127~0 (16 values)" 1270,8,16,24,32,40,48,

56,64,72,80,88,96,104,112,120,127

"0~120,A/B,AB Of" 11 AB On 0~120 A/B/AB On/Of

"0~127 (16 values) " 00,8,16,24,32,40,48,

56,64,72,80,88,96,104,112,120,127

"127~0 (16 values)" 1270,8,16,24,32,40,48,

56,64,72,80,88,96,104,112,120,127

"On/Off" Of On/Of

"On/Off Of On/Of

"On/Off" Of On/Of

"On/Off" Of On/Of

"0~127/Off" 0 On 0~127 On/Of

"0~127/Off" 0 On 0~127 On/Of

"1~128/Off" 1 On 1~128 On/Of

"0~120" 91 0~120 On/Of

"0~127/Off" 40 Of 0~127 On/Of

"0~120" 93 0~120 On/Of

"0~127/Off" 0 Of 0~127 On/Of

"0~127/Off" 0 On 0~127 On/Of

"0~127/Off" 0 On 0~127 On/Of

"1~128/Off"v 1 On 1~128 On/Of

"0~120" 91 0~120 On/Of

"0~127/Off" 40 Of 0~127 On/Of

"0~120" 93 0~120 On/Of

"0~127/Off" 0 Of 0~127 On/Of


55/57


TECHNICAL SPECIFICATIONS

MIDI System Exclusive ID Number: 00H2037H

RX MIDI CHANNEL: 1, 2, 3, …, 16, OMNI

TX MIDI CHANNEL: CHANNEL A: 1, 2, 3, …, 16CHANNEL B: 1, 2, 3, …, 16

MIDI MESSAGGES: cc00, cc32, PC, cc07, cc10, cc16, cc91,

cc93, cc94, Start (FA), Stop (FC),

Continue (FB), Song Select (F3), XXcc,

YYcc

PEDALBOARD SWITCHES

FUNCTIONS: ccXX/Continue, 10 /cc00, 0/cc32,1/pc0-127, 2/pc1-128, 3/cc07, 4/cc10,

ccYY/Start-Stop, Select/Channel,

10 /cc11, 5/cc16, 6/cc91, 7/cc93,

8/cc94, 9/Song, Mode/Write

DISPLAY: LCD with contrast control 16 character xuna line. Dim. 6.0 x 12.72 (W x H) mm.

POWER: DC IN supply 12/9V cc 750mA.

DC IN with Phantom Power through the MIDI

IN

MIDI: 1 Midi OUT with Phantom Power – 7 PIN/DIN1 Midi IN – 5 PIN/DIN

1 Midi THRU – 5 PIN/DIN

LIMITATIONS: The MS-32 is limited only to the

transmission of the messages listed on

page 3 of the owner’s manual. Proel

S.p.A. is not responsible for a different

use.

This product responds to the 83/33 E.C. directives concerning the elettro-magnetical compatibility (EMC)


56/57


SPARE PARTS & OPTIONALS

SPARE PARTS

PROEL/DISPLAY: Cod. 91LCDM32

PROEL/DISPLAY LABEL: Cod. 92ETCM32

PROEL/SWITCHS LABELS: Cod. 92ETTM32

PROEL/MIDI 5 PIN SOCKET: Cod. 91PRD5PL

PROEL/MIDI 7 PIN SOCKET: Cod. 91PRD7PL

PROEL/JACK SOCKET: Cod. P385

PROEL/DC IN SOCKET: Cod. PA38/25

PROEL/SWITCH: Cod. 93TSTCHP

PROEL/POWER SUPPLY: Cod. PPSM16

OPTIONALS

PROEL/DIN 7 PIN CABLE: Cod. RLD700

PROEL/DIN 5 PIN CABLE: Cod. SH120

PROEL/FOOT CONTROLLER: Cod. PVP16L

PROEL/PATCH BAY MONO CABLE: Cod. ROAD100LU5

PROEL/OWNER’S MANUAL: Cod. 92MNIM32

PROEL/HARD CASE FOR MS32: Cod. CPMS32


57/57

PROEL S.p.A.Zona Artigianale64027 Sant’Omero (TE) – ItalyTel: +39 0861 81241Fax: +39 0861 887862Proel web site: www.proelgroup.comE-mail: [email protected]

Copyright © 1999 PROEL S.p.A.Manufactured and printed in Italy

proel ms32 manual

Documents