production of single cell protein from natural gas john villadsen center for biochemical engineering...
TRANSCRIPT
Production of Single Cell Protein from Natural Gas
John Villadsen
Center for Biochemical Engineering
Technical University of Denmark
Genome of Methylococcus capsulatus
The bacteria with membrane bound Methane-monooxidase
Dividing M. capsulatus with clearly visible membranes
The key-enzyme Methane monooxygenase
Capture of CH4 by Methane monooxygenase
Further oxydation of methanol in the organism
Methane and Oxygen demand for SCP production
• From 1.25 kg methane one obtains 1 kg biomass*)
This corresponds to 1 kg biomass per 1.75 N m3 methane
or Ysx = 0.520 C-mole biomass per C-mole methane
• The O2 demand is (8 – 0.520٠4.20) / 4 = 1.45 mol O2 per C-mole CH4
or 2.53 N m3 O2 / kg biomass = 3.62 kg O2 / kg biomass.
Stoichiometry of methane conversion to biomass:
CH4 + 1.45 O2 + 0.104 NH3 → 0.52 CH1.8O0.5N0.2 + 0.48 CO2 + 1.69 H2O
*) Reference : Wendlandt, K.D, Jechorek, M, Brühl, E.
”The influence of Pressure on the growth of Methanotrophic Bacteria”
Acta Biotechnol. 13, 111-113 (1993)
and industrial experience: Dansk Bioprotein A/S 1992 - present.
Demand for heat removal
The reaction should take place at ≈ 45o C, the optimal temperature for
Methylococcus capsulatus fermentation.
Stoichiometry:
CH4 + 1.45 O2 + 0.104 NH3 → 0.52 CH1.8O0.5N0.2 + 0.48 CO2 + 1.69 H2O
Heat of reaction 460Yso kJ (C-mol carbon source)-1
or Q = 460٠ 1.45 = 667 kJ (mole CH4)-1 = 52 MJ (kg biomass)-1
This is an appreciable heat duty!
Demand for O2 and CH4 mass transfer
• The production rate depends on the rates of two separate processes
A. The reaction between bacteria and dissolved O2 + CH4
B. The rate of mass transfer from gas- to liquid phase.
The ”bio-chemical” reaction is limited by NH3 since we need to keep the
NH3 concentration below about 40 mg L-1 to avoid formation of NO2-
which is toxic to the bacteria. At 30 mg L-1 the rate is
qx = 0.21 X kg m-3 h-1
where X is the biomass concentration in kg m-3.
But qo2 = (1.45 / 0.52)(1000 / 24.6) qx = 113 qx mol m-3 h-1
= kl a (cO2* - cO2)
where cO2* and cO2 are respectively the saturation and the actual O2
concentrations in the liquid.
Factors that affect the mass transfer
The rate of mass transfer kl a (cO2* - cO2) (and kl a (cCH4* - cCH4))
depend on :
A. The mass transfer coefficient kl a
Maximum achievable kl a ≈ 1200 h-1
B. cO2*
C. cO2
cO2* is proportional with the partial pressure of O2 in the gas phase.
At 1 atm total pressure and pure O2 one obtains cO2* = 0.9 mM (45o C)
cO2 should be above about 20 μM to keep the organism healthy.
The switch from bioreaction control to mass transfer control
Assume that we wish to have X = 20 kg m-3 (qx = 4.2 kg m-3 h-1)
qO2 = 113 ٠ 4.2 = 475 mol m-3 h-1 = kl a (cO2* - 20) 10-3 mol m-3 h-1
For kl a = 1000 h-1 cO2* must be > 495 μM to obtain a gas transfer rate
that is higher than the rate of the liquid phase reaction 4.2 kg m-3 h-1.
For a total pressure of 1 atm and pure O2 (cO2* = 900 μM) about 50 %
of the oxygen is consumed before O2 limitation sets in.
With O2 extracted from air (21% O2, cO2* = 189 μM) oxygen limitation
prevails throughout the reactor.
With pure oxygen and 4 atm total pressure (cO2* = 3600 μM) O2
limitation occurs only in the last ≈ 14 % of the reactor.
Consequences of O2 limitation
The constant production rate qx = 4.2 kg m-3 h-1 can not be maintained
The production rate in the last part of the reactor is 1st order in cO2*
If we wish a high utilization of O2 (e.g. 95 %) the reactor volume may
increase beyond reasonable limits (or qx may decrease to an
unacceptably low level).
Reactor design
• A stirred tank reactor is hopeless: We wish the first order conversion of O2 in the last part of the reactor to proceed in plug-flow mode. In a CSTR cO2* would be 0.05 of inlet value.
• The large heat release dictates that external heat exchange is to be used.
• Liquid and gas is forced through a number of stationary mixer elements at a velocity of ≈ 1 m s -1. Gas is injected through an ejector. Ample allocation of head space assures gas/liquid separation. Holding time for liquid ≈ 5 h and for gas ≈ 60 s.
• Centrifuges (or drum filters) are used to separate biomass from liquid.
• Ultrafiltration gives ≈ 20 wt% biomass sludge. Spray drying gives the final powdery product
• Heat shock treatment (123 oC, 2-5 min) removes nucleic acids and gives a product suitable for direct human consumption.
500 L pilot plant loop-fermentor at DTU
6
11
4
12
5
7
10
3
10
89
11
11
66
1111
44
1122
55
77
1010
33
1010
8899
1111
1111
Design of a 10 m3 loop reactor
A 10 m3 fermentor
250 m3 reactor (≈ 9000 t year-1 production) in Norway