origami inspired design of a hydraulic tele...
TRANSCRIPT
-
Abstract
Origami-engineering is an emerging design and manufacturing technology for creating three-dimensional robotic systems
using two-dimensional designs. We present a new micromanipulation system featuring origami-inspired minimal design and
hydraulic teleoperation. Operators move wearable user-interface-devices on their fingers to control a multi degree-of-freedom
micromanipulator where a simple hydraulic system using syringes of different diameters allows motion reduction and force
transmission between the master (finger exoskeletons) and the slave (manipulator). The paper presents design considerations
and features for creating the origami-based hydraulic tele-micromanipulation system using inexpensive paper cardboards and
disposable syringes. Finally, a range of different high level micromanipulation abilities such as trajectory following,
pick-and-place, micro-separation, and 3D micro-assembly are demonstrated. Highlighting rapid design and fabrication of a
low-cost precision micromanipulation system, this paper proposes new applications of origami-inspired robots to wearable
robots and micro robotic manipulation.
1. Introduction
Traditional robots are complex electro-mechanical systems consisting of sensors, actuators, and mechanical structures,
controlled by a programmable computer. Thus, developing functional robotic systems is very expensive from time and cost
perspectives. The printable programmable robot paradigm is an emerging technology for creating three-dimensional robotic
systems using two-dimensional features (Mehta et al., 2014; Onal et al., 2011). This technical approach allows rapid design and
fabrication of mass-producible and customizable miniature robotic systems. As a result, different origami-based robotic systems
such as autonomous hexapod robots (Soltero et al., 2013), inchworm robots (Felton et al., 2013), thermally-actuated
programmable matter (Hawkes et al., 2010), a miniature quad-rotor (Mehta et al., 2013), and thermally activated, configurable
electric devices are proposed (An et al., 2014; Felton et al., 2014; Miyashita et al., 2014; Tolley et al., 2014).
Previously, we introduced a paper-made tele-micromanipulation system and its preliminary results, highlighting new
applications of origami-inspired robots to wearable devices and micro robotic manipulation (Yim and Kim et al., 2015).
Micromanipulation is the key technology for applications in micro-manufacturing (Bhattacharyya et al., 2001; Shimada et al.,
2000), micro-assembly (Popa et al., 2004; Thompson et al., 2001), clinical micro-surgery (Yasargil et al., 2006; Boecks et al.,
1976), cell manipulation (Gauthier et al., 2006; Tabares et al., 2010), and biomedical engineering research (Causa et al., 2007;
Inoue et al., 2005). However, the working ranges and resolution of commercial micromanipulators are set for several target
applications such as transgenics (Kawase et al., 2001; Caron et al., 2000), neuroscience (Rebec et al., 1993; Tan et al., 1993), and
in-vitro fertilization (Steirteghem et al., 1994). Also, those systems consist of very expensive electric motors or piezoelectric
S. Yim and S. Kim are with the mechanical engineering department of Massachusetts Institute of Technology, and Shuhei Miyashita and Daniela Rus are with
Computer Science and Artificial Intelligence Laboratory of Massachusetts Institute of Technology, Cambridge, MA 02139 USA.
Origami-Inspired Design of a Hydraulic
Tele-Micromanipulation System
Sehyuk Yim, Shuhei Miyashita, Daniela Rus, and Sangbae Kim
-
actuators, gears, precision linear stages, and user-interface-devices. In this paper, we present an advanced origami-inspired
hydraulic tele-micromanipulation system with detailed analysis and quantified experimental results. The proposed
micromanipulation system is easy-to-design in a computer-aided-design program, easy-to-make by using a laser cutting machine,
cost-effective because it is made of low-cost paper cardboards and disposable syringes, and its working range and resolution are
customizable by changing the motion reduction ratio of the hydraulic system.
This paper contributes the following four aspects:
This is the first origami-based tele-micromanipulation system where both the wearable user-interface-devices and the
slave manipulator are manufactured by printing and folding.
This paper presents key origami elements for the precise linear motion of the slave micromanipulator. These elements
are also useful in designing other origami-based devices requiring precise motion.
The minimal ergonomic designs of finger exoskeleton interfaces are expandable to other wearable devices or
human-machine interface devices.
We developed a crease pattern design method for integrating multiple single-sided foldable structures into one pattern.
As a result, each origami-based device consisting of complex three-dimensional mechanisms is manufactured from one
single paper cardboard where flexure hinges and rigid frames are easily implemented using the thick material.
The paper is organized as follows. Section 2 describes the overall manipulation system. Section 3 and 4 introduce the design
features, considerations and manufacturing methods of the finger exoskeletons and the micromanipulator, respectively. Section 5
evaluates the motion precision of the manipulation system quantitatively, and demonstrates different manipulation abilities. In
Section 6, the contribution and limitations of the current system are discussed.
Fig. 1. A photograph of the origami-inspired hydraulic tele-micromanipulation system consisting of the paper-made finger
exoskeletons (left) and micromanipulator (right). Operators move wearable user-interface-devices on their fingers to control
the micromanipulator. The hydraulic system using syringes of different diameters allows motion reduction and force
transmission between the master (finger exoskeletons) and the slave (manipulator).
-
2. System Overview
The developed micromanipulation system consists of hydraulically connected two mechanical systems. One is the
finger exoskeletons that users control like user-interface-devices (master), and the other is the micromanipulator acting
as a slave. Figure 2 shows a schematic diagram of the system. The motion of the finger exoskeleton synchronized with
each finger is reduced in the manipulator domain via the hydraulic motion reduction system using two syringes of
different diameters where the motion reduction ratio is determined by the cross-sectional area ratio of the syringes. Four
finger exoskeletons are required to produce the manipulator’s x-, y-, z- motions and the grippers’ motion. As a result,
operators can pick and place micro objects in a three-dimensional space with the wearable user-interface-devices on
their fingers, monitoring the positions of the micro objects and the motion of the manipulator tip in displayed video
images. Table 1 shows the specifications of the micromanipulator and finger exoskeletons.
Table 1. Specifications of the manipulator and interface devices.
Micromanipulator
degree-of-freedom 4 (x,y,z, and g-motions)
workspace (x × y × z) < 7×7×10 mm3
main materials paper cardboard
(thickness:1.2 mm, Blick, US)
height (z-axis) 70 mm
length (x-axis) 250 mm
width (y-axis) 60 mm
weight 50.7g
embedded syringe 3 cm3
Finger exoskeletons
rotational angle range (thumb)
maximum motion distance (index and middle)
30° - 85°
< 20 mm
main materials paper cardboard
weight 18g
Embedded syringe 1 cm3
-
3. Wearable user-interface-devices: paper-made finger exoskeletons
3.1. Motion Mapping Strategy
Human fingers are excellent biomechanical systems for interfacing with machines because their dense and sensitive muscular
system allows for precise and dexterous control of their motions. The user-interface-devices of the micromanipulation system are
wearable on thumb, index, and middle fingers (Fig. 3). The bending angles (α, β, and γ) of the three finger modules correspond to
the 3D position (x, y, and z) of the manipulator tip. This motion mapping strategy presents that the 3-D motion of the manipulator
is decomposed into three 1D motions, which are independently controlled by multiple user-interface-devices.
Fig. 2. A schematic diagram of the developed hydraulic tele-micromanipulation system. The middle, index and thumb fingers
of the left hand (section 3) move the manipulator tip in the x-, y-, and z-directions using linear motion stages (section 4.1),
repsectively, and the index finger of the right hand controls grippers (section 4.2). The motions of the finger exoskeletons are
reduced in the micromanipulator domain by the hydraulic motion reduction system (section 4.3). The microscope above the
manipulator and a monitor provide the display for visual feedback to the human operator.
-
3.2. Index and Middle Finger Exoskeletons
Each finger exoskeleton device has one degree-of-freedom motion to implement the motion mapping strategy in Fig. 3. We
designed the finger exoskeletons considering the ergonomics of fingers. Figure 4(a)-(b) shows the design and motion of the index
(and/or middle) finger exoskeleton. One rigid rectangular parallelepiped holds the proximal phalanx, which becomes the
reference. If the finger is bent by contracting the flexor muscle, the distal phalanx (or the middle one) slightly slides in the second
rectangular parallelepiped in its length direction, pressing the bottom surface in the normal direction. The expanding syringe
draws water from the other syringe in the manipulator (Section 4.3 details this hydraulic mechanism). If the finger is relaxed by
contracting the extensor muscle, the produced torque compresses the syringe piston and pushes water to the manipulator syringe
where the two phalanx holders are connected by the point of lever. Figure 5 shows the free-body-diagram of the exoskeleton to
obtain analytical equations about the motion and force relation. The linear displacement of the syringe piston is expressed as
)2
sin(2 mm rd
(1)
where θm is the angle between two phalanx holders, r is the height of the finger holder, and dm is the distance between two
surfaces P1 and P2. On the basis of the rotational moment law, the relation between the finger pressing (and/or pulling) force and
the linear force on the syringe piston is expressed as
inout F
rr
aF
2cos2
2
(2)
Equation (2) is plotted as Fig. 5(b), showing that the output/input force ratio is determined by the rotational angle and the ratio
between the length and height of the distal phalanx holder.
Fig. 3. Motion mapping between the finger exoskeletons in the master domain and the micromaniplator tip in the slave
domain. The 3D motion of the manipulator tip is controlled by the three fingers’ bending motions. The black dots and the
yellow dots mean the reference points and the moving points, respectively. The blue dotted arrows indicate the corresponding
pairs.
-
Fig. 4. Motion of the index (or middle) finger in the finger exoskeleton. (a) Initial state. (b) Deployed state. The
displacement of the syringe is synchronized with the motion of the finger. The blue solid line and the red arrow indicate the
rotation of the exoskeleton and the expansion of the syringe, respectively.
Fig. 5. (a) A free-body-diagram of the index finger exoskeleton. The syringe piston is moved by the rotation of the distal
phalanx holder. (b) The ratio between the syringe force (Fout) and the finger force (Fin) is dependent on the rotational angle (θ)
and the ratio between a and r, which are the length and the height of the distal phalanx. The green region shows the working
range of the finger exoskeleton, between about 30° and 85° degree.
Fig. 6. The unfolded crease pattern of the index finger exoskeleton. The red surfaces (B) and the dark-gray surfaces (E)
become piston and syringe holders, respectively. The blue-colored surfaces (A) and the light-gray surfaces (D) become
phalanx holders. The green surfaces connect two phalanx holders. There are four pairs of connecting surfaces (A1 and B1, A2
and C2, C3 and D3, and D4 and E4).
-
Each exoskeleton component is a folded structure. Figure 6 shows the unfolded crease pattern of the finger exoskeleton
consisting of four parts (A, B, C and D). The green surfaces (C) are folded about the center line. The blue surfaces become the
rigid rectangular parallelepiped for holding the distal phalanx. The surfaces A2 and C2 connecting the parts A and C are folded
back-to-back. As a result the surface C2 is located inside the rigid rectangular parallelepiped. The light-gray surfaces (D) become
the rigid rectangular structure for holding the proximal phalanx. The surfaces D3 and C3 connecting the parts D and C are folded
back-to-back. The surface C3 is located inside the rigid rectangular parallelepiped. The dark-gray surfaces and the red surfaces
become compliant rectangular parallelepipeds, holding the syringe and the piston, respectively. The surfaces D4-E4, and A1-B1
are folded back-to-back as the previous connecting surfaces.
The back-to-back folding surfaces play two important roles in the origami structure. First, they change the folding directions
of structures, so that complex shape three-dimensional structures are integrated into one and made from one single paper. Figure
7(a)-(b) show simple examples. If the surfaces Ac and Bc connecting two parts are folded back-to-back, the folding direction
changes after these connecting surfaces. This property was used multiple times when designing the crease pattern of the finger
exoskeleton to integrate four rectangular parallelepipeds into one.
Second, it is possible to adjust the rigidity of the 3D structure using the length (and/or width) margin of the connecting
surfaces. For example, while the syringe and piston holders are easily slanted by the orientation of the syringe, the phalanx
holders are very rigid because the surfaces C2 and C3 inside the phalanx holders do not have a length margin for the surrounding
structures to move (i.e., LC2 = LA2 and LC3 = LD3).
Fig. 7. Changing the folding direction of the single-sided foldable structure using the back-to-back folding surfaces (Ac and
Bc).
-
3.3. Thumb exoskeletons
Thumbs have two short phalanxes of which bending angles are relatively limited. Thus, thumb exoskeletons need a different
design from the index finger exoskeleton, considering ergonomics. Figure 8 shows the minimal design for the thumb exoskeleton,
which is made of a single paper cardboard. The device holds the operator’s palm and distal phalanx using the rigid rectangular
structures (D and A), respectively. The syringe piston is pushed (or pulled) in the c-direction by the thumb holder. The foldable
linkages (B) protects this linear motion. The rotational joint (C) connecting the linearly moving parts (A and B) to the palm
holder (D) is passively rotated about the e-axis by the position and orientation the thumb phalanx. This passive joint is
Fig. 8. Motion of the thumb in the exoskeleton. (a) Initial state. The dashed lines present the axes (c and e). A: phalanx
holder, B: foldable linkages for the syringe’s linear motion, C: passive joint, D: palm holder. (b) Compressed state. The right
blue arrow indicates the applied force direction (or the moving direction of the piston). h means the displacement of the
piston. The left arrow shows the passive rotation (θp) of the connecting joint about the e-axis.
Fig. 9. The workspace of the center of the thumb phalanx holder where P0 is [15 0 30]T, its linear displacement (hα) changes
between 0 and 20 mm, and the passive rotational angle (θp) changes between 0° and 30°.
10 20 30 4015
20
25
30
35
40
45
50
55
s (mm)
c (
mm
)
-
ergonomically important to make operators feel comfortable during operation. Equation (3) shows the matrix form equation to
calculate the three-dimensional center of the phalanx holder, Pt = [st et ct]T.
1
)(
1000
0)(cos0)(sin
0010
0)(sin0)(cos
1
0
0
0
thc
e
s
tt
tt
c
e
s
app
pp
t
t
t
(3)
where θp is the rotational angle of the passive joint, P0 = [s0 e0 c0]T is the initial position of the center of the thumb phalanx holder,
and ha is the displacement of the syringe piston in the c’-direction. Fig. 9 shows the two-dimensional workspace of Pt considering
the design variables of the thumb exoskeleton.
Figure 10 shows the unfolded crease pattern, which consists of four parts including three pairs (A1/B1, B2/C2, and C3/D4) of
back-to-back folding surfaces. The palm holder has a bi-layer to strengthen the mechanical robustness because it should not be
rotated or distorted when the finger pushes (or pulls) the piston. The left foldable line of the surface A1 is slanted to make the
thumb phalanx fit into the holder.
3.4. Material and manufacturing methods
We used 1.2 mm thickness paper cardboards, which are made of alpha-cellulose pulp from purified wood fiber. The laser-cutting
machine engraves or cuts the paper cardboard, following all lines of the designed crease pattern. The laser beam frequency is set
low around 280 Hz not to burn the paper. The outer lines are cut through by a high power laser-beam (> 30%). The foldable lines
are engraved by a week laser beam (15-20%). The thickness of the hinge determines its compliance. The stiffness of the flexure
hinge is analytically modeled as
l
Ewtk
12
3
(4)
Fig. 10. The crease pattern of the thumb exoskeleton. Blue surfaces (A): the phalanx holder. Red surfaces (B): the linear
motion linkages. Gray surfaces (C): the passive rotational joint. (D) Yellow surfaces: the palm holder.
-
where l is the length of the engraved hinge, t is the thickness, w is the width into the surface, and E is the Young’s modulus of the
paper cardboard (Hoover et al., 2009). This equation presents that the thickness of hinge is the most critical factor to determine its
compliance.
Thin flexure hinges have wide bending angles, but their durability is limited because of fatigue failure. Thus, the foldable lines
should be engraved by different settings in the laser machine considering their roles in each structures. Figure 11(a)-(c) shows
several flexure hinges of different thicknesses. For example, the back-to-back folding surfaces should have very compliant
flexure hinges for precise alignment even in a wide bending angle (θ = 180). On the other hand, the slanting rectangular
structures (the parts B and E in Fig. 6) and the linear linkages (the part B in Fig. 10) need to have thicker flexure hinges because
durability is important and their bending angle is not wide (θ < 90). Thick hinges are destroyed even in a small bending angle
because of the material property (Fig. 11(c)).
The reason that single-sided foldable hinges are used in the proposed micromanipulation system is related to the
manufacturing process. Technically, it would not be easy to design the crease pattern of 3D origami structures employing only
single-sided foldable hinges because the back-to-back folding surfaces should be embedded between patterns. Assuming the use
of double-sided foldable hinges, the crease pattern would be easily designed without the integration process. However, both
surfaces of paper cardboards have to be engraved (and/or cut) by a laser beam machine, which requires manual intervention
between the steps (Yim and Kim et al., 2015). If the paper cardboards are not precisely aligned in the machine, the crease patterns
on their both sides have double outlines and foldable lines, and then they are not assembled accurately. This point is particularly
disadvantages for manufacturing precision linear motion stages.
4. Paper-made slave micromanipulator
4.1. Design features
Thick paper cardboards are useful materials for origami-based devices because rigid surfaces are folded accurately about
laser-engraved lines, not requiring additional compliant layers for flexure hinges (see Fig. 11). However, their inherent deflection
is a major drawback for the material of a precision motion system. We developed two key origami-elements to compensate for
this disadvantage.
Fig. 11. Microscopic images (side view) of the engraved flexure hinges after the laser beam machining (Epilog Zing 30W, US).
(a) 100% speed and 20% power: t = 1.2 mm. (b) 100% speed and 15% power: 0.42 mm, and (c) 100% speed and 12% power:
0.85 mm.
-
The first element is Sarrus linkage mechanism (Fig. 12(a)). Three pairs of foldable surfaces allow the precise linear motion of
the surface S, preventing its rotation or translation in other directions. Its translational stiffness in the x- and the z-direction are,
respectively, expressed as
3
3
3l
Etwk Rx (5)
3
3
3
2
l
Ethk Rz (6)
where wR and hR are the width and the height of the surface R. Geometrically, the ratios wRl-1 and hRl-1 are very high, and the
translational stiffness, kx and kz, are proportional to the third order of them.
The second key element is the bilayer cantilever with the folded side surface (Fig. 12(b)). The lower layer (F) removes the
residual stress of the upper layer (E) first. Straightness propagate along the folded line between the side surface (G) and the upper
surface. The bending stiffness of this structure about the x-axis is expressed as the equation (7). The first term and the second
term indicate the effect of the bilayer cantilever and the folded side surface, respectively.
s
wE
s
wE
s
EwR GGEx
121212
8333
(7)
The stiffness of this origami-element is about 315 times bigger than that of the single layer cantilever where we is 20mm, δ is 1.2
mm, s is 65 mm, and wg is 20mm.
The micromanipulator consists of four linear motion stages (Fig. 13). The x-, y- and g-motion stages are integrated together (g
means grippers). The z-motion stage is separated from the other motion stages, and has a cantilever, the arena of micro objects.
All motion stages are above the flat metallic surface with a low friction force. This single-storey micromanipulator minimizes the
deflection of the motion stages due to their weights. Figure 14 describes the connection of the motion stages using a simplified
schematic diagram. The active x-stage and the passive x-stage are fixed on the metallic plate by small magnets. The passive
x-stage (Xp) at the opposite side does not have a syringe, and only assists the linear motion of the active x-stage (Xa) not to be bent.
The two x-stages move the attached wide flat plate in the x-direction where the y-motion stage (Y) is fixed at one edge of the plate.
The y-motion stage moves the attached g-motion stage (G) in the y-direction. As a result, the gripper stage slides on the plate in
the x- and y-directions by Xa, Xp and Y. The g-motion stage (G) provides one degree-of-freedom to one gripper on the cantilever
Fig. 12. Critical elements of the linear motion stages. (a) Sarrus linkage mechanism. The surface S moves linearly from the
reference surface, R, under the guidance of three pairs of foldable surfaces A, B, and C. (b) The bilayer cantilever, E and F,
with the folded side surface, G, improves the straightness of the cantilever.
-
(the other gripper on the other cantilever is stationary). The z-motion stage has three pairs of linkages folding in three directions
in equilibrium, which minimizes the deflection of the top surface. Micro objects are located on the long bilayer cantilever
connected the top surface of the z-motion stage.
Figure 15(a)-(d) show the unfolded crease pattern of the motion stages. The x-stage has one pair of back-to-back folding
surfaces to change the folding direction. All stages employ Sarrus linkage mechanism. The y-, z-, and g-stages have the
orthogonal bi-layer structure. The cantilever of the z-stage becomes the arena for micro objects to be manipulated. Grippers are
fixed in the slots in the g-stage cantilever.
Fig. 13. A photograph of the origami-based paper-made micromanipulator (four degree-of-freedom) on the flat metallic
plate. Xp and Xa, Y, Z and G are the x-, y-, z- and g-motion stages, respectively. The coordinate is presented on the lower-left
corner.
Fig. 14. A connection diagram of the motion stages. Xa and Xp are fixed on the surface by the magnets (red). The
manipulator tip is movable in the x-, and y-directions, and G provides one more degree of freedom for the grippers’ motion.
The arena is moved by Z anchored on the surface.
-
4.2. Grippers
Grippers are critical in performing advanced micromanipulation tasks such as pick-and-place and 3D micro-assembly. In
accordance with the design paradigm of printable programmable robots, we developed two kinds of paper-made grippers, which
are mass-producible with laser cutting machines, replaceable, customizable, and fixed with the g-motion stage without
adhesives.
i) Laser-machined 2D grippers: vertical grippers are orthogonally fixed to the cantilever using small slits (see A in Fig. 16). They
are arc-shaped, so that their sharp tips do not touch other micro objects on the arena during manipulation. The horizontal grippers
have a trapezoidal shape, and their inner-surface is cut to secure the sight of the microscope (see B in Fig. 16). Both vertical and
horizontal grippers are manufactured by using a laser cutting machine. 200 μm is the minimum width of the grippers to maintain
their mechanical strength for gripping micro objects. Using our current fabrication method and equipment (Epilog Zing laser
series 30W), it is difficult to make grippers thinner than this dimension because the burning effect of the laser beam ruins the
designed geometry.
Fig. 15. The crease pattern of the motion stages. (a) The active x-motion stage. The blue arrows indicate the back-to-back
folding surfaces. (b) The y-motion stage. (c) The g-motion stage. (d) The z-motion stage. The red arrows present the bilayer
cantilever with an orthogonally folded side surface. All figures are not drawn to scale.
-
ii) Origami-based compliant 3D grippers: origami engineering allows fabrication of compliant 3D grippers, which have two
benefits than the 2D grippers. First, the shape of their tips is customizable according to the shape of the object to be manipulated.
Second, the stress on the manipulated objects is minimized because thin film-made grippers are slightly deformed by the
interaction with objects. These features are useful to grip fragile or biological materials. Figure 18 and 19 depict origami-inspired
compliant 3D grippers and the crease pattern, respectively. The geometry is designed such that the tip angle of the gripper can be
instantly varied with a minimal modification in the design, i.e., α, whereas keeping two β the same angle ensures that the surface
can be folded full-flat thus the mechanical latches function to solidify the structure, permitting minimum deformation when
grabbing an object. On the other hand, by releasing the latches, the grippers gain certain compliance for soft handling of an object.
An observing window was added to visually capture awaiting micro objects under the cantilever to be assembled. The employed
manufacturing process is the same as in Section 3.4., with a weaker set of laser power (5%). The assembly was made by
manually folding along the creases without any usage of tools or adhesives. Except a latching process which requires
deformation of a sheet material, the assembly process can also be performed by self-folding technique (Miyashita et al., 2014;
Tolley et al., 2014).
Fig. 16. Laser-machined 2D grippers fixed on the bilayer cantilever of the g-motion stage. A: hook-shaped vertical grippers.
B: Trapezoidal-shaped horizontal grippers. The long bilayer cantilever of the z-motion stage becomes the arena for micro
objects to be manipulated.
Fig. 17. Microscopic images of the laser-machined grippers. (a) Hook-shaped gripper (side-view) (b) Trapezoidal horizontal
gripper (top-view). (c) Chopstick-shaped horizontal gripper (top-view). The yellow boxes show the position of 500 μm-sized
micro objects.
-
4.3. Hydraulic motion reduction
Each motion stage of the micromanipulator is moved by the hydraulic motion reduction mechanism using two syringes of
different diameters. Compression and expansion of the master syringe in the finger exoskeleton enables expansion and
compression of the slave syringe in the manipulator, respectively. Assuming that water is incompressible and not vaporized
inside the syringe, the displacements of the pistons in two syringes are inversely proportional to their cross-sectional area ratio.
Equations (8) and (9) show linear displacements of the motion stages as a function of the corresponding finger motion,
respectively.
),,()2
sin2
(sin20,,
stagesgandyxrdmtm
s
(8)
)(, stagezdd thumbms (9)
where α is the cross-sectional area ratio between the master syringe cylinder and the slave syringe cylinder. Table 2 shows the
look-up-table about the motion of each finger and the moving direction of the corresponding motion stage.
Fig. 18. Origami-inspired thin grippers fixed to the cantilever of the gripper stage.
Fig. 19. The unfolded crease pattern of the origami-inspired grippers. The design variables: α = 90° and β = 85°.
-
Table 2. Look-up-table about the moving direction of the manipulator tip by the finger motion.
Bending motion Straightening motion
Left index -Y +Y
Left middle +X -X
Left thumb -Z +Z
Right index gripping releasing
The employed hydraulic motion reduction system has a single-acting-unit, without a compressible spring preloading the
piston in the opposite direction. We experimentally evaluated whether this motion reduction system is repeatable and consistent.
We attached different weights (50g, 100g and 200g) to the piston bottom to cause an external load, continuously repeated full
expansion (θm = 100°) and full compression (θm = 20°) of the index finger exoskeleton twenty times in each condition, and
measured the position of the piston in the slave syringe. Table 3 shows the average and standard deviation of the gradients
between two points, presenting that the motion reduction ratio is consistent even when the external load is applied to the system.
Table 3. Hydraulic motion reduction between the index finger exoskeleton and the motion stage.
Fload (mN) (ds,max - ds,min )(θm,max - θm,max)-1 [mm/degree]
-490 - 0.075 ± 0.0029
-980 - 0.078 ± 0.0022
-1960 - 0.078 ± 0.0045
The hydraulic motion reduction mechanism allows force transmission between the operator and the manipulated object. Note
that this is applicable only when compressing the master syringe. Equation (10) shows the relation of forces produced in two
syringes when compressing the master syringe.
)( slavemaster FSVDF (10)
where Fmaster is the applied force to the piston in the master syringe, D is the frictional force between the master syringe and the
piston, V is the viscous friction between the flowing water and the internal surfaces of syringes and a tube, S is the frictional force
between the slave syringe and the piston, and Fslave is the output force of the piston at the slave syringe. This equation presents
that Fslave is proportional to Fmaster, and the ratio is constant.
We investigated the force transmission between the master and slave syringes in experiments. They are fixed in the air by
holders, and load cells are attached to pistons respectively (Fig. 20(a)). A compliant object was placed between the slave syringe
piston and the bottom surface. We pressed the master syringe piston, and measured the forces (Fmaster and Fslave) using the load
cells. The experiments were repeated after changing the compliant object to a rigid one. The experimental results show two
analysis (Fig. 20(b)). First, the interaction force between the slave syringe piston and the object is linearly proportional to the
applied force to the master syringe piston. The gradient of the plot is about 3.72, and consistent regardless of the compliance of
the object below the slave syringe piston. The cross-sectional area ratio of the two syringes is 1:4.2. Considering the
measurement noise and the error due to the inflation of the tube, the experimental results are consistent with the theory. Second,
the total frictional force in the hydraulic system is around 1 N. If the applied force becomes higher than 1N (see the dashed-line
-
box in Fig. 20(b)), the piston slightly starts to move because of the inflation of the water-filled tube or the deformation of the
object. The linear relation between Fslave and Fmaster is valid only when the applied force is stronger than this inherent load.
5. Experiments
This section describes experimental results for micromanipulation with our system. All demonstrations are included in the
supplementary multimedia file. The operator was trained for two hours to become familiar with the mobility and the moving
direction of the manipulator in the displayed video images. As the operator’s skill and experience improved, finally, the
success/failure ratio became higher than 80%.
i) Motion precision: first, we evaluated the straightness of each motion stage and xy orthogonality (Fig. 21). We placed a small
ink-jet printed circle (diameter: 1.2 mm) on the cantilever of the g-motion stage, and manipulated it using the finger exoskeletons.
Figure 21(a)-(c) show the centroid of the circle while the manipulator is moved in the z-, x- and y-directions, respectively. We
defined that the straightness is the maximum gap distance between two lines moving back and forth divided by the one-way
length during the linear round trip. The angle between two lines moving in the x- and y-directions presents the orthogonality (Fig.
21(d)). The experiments were repeated three times in each case, and the results are summarized in Table 4. The straightness and
the xy orthogonality of the linear motion stages are also affected by the precision in assembly and alignment of parts. Technically,
Fig. 20. Force transmission experiments. (a) A schematic figure of the experimental setup for measuring the interaction
forces. The cross-sectional area ratio of the two syringes is 1:4.2. (b) The interaction force (Fslave) between the slave syringe
piston and the object is proportional to the applied force (Fmaster) to the master syringe piston regardless of the compliance of
the objects. The green arrow indicates the sum of the frictional forces modeled in the equation 10.
-
however, 0.25 – 0.96% straightness and the orthogonality error below 0.5° are achievable only when i) the deflections of paper
cardboards are compensated by using the presented origami elements, and ii) the origami-based linkages mechanisms guide the
linear motion of the stages precisely.
Table 4. The motion precision of each stage
Straightness of the motion stages XY orthogonality
X 0.0030 ± 0.0004
89.5 ± 0.96 [deg] Y 0.0025 ± 0.0012
Z 0.0096 ± 0.0004
ii) 2D trajectory following: we set three letters, MIT, on the arena, and controlled the micromanipulator tip to follow the letters
(width: 400 μm). Figure 22 shows the trace of the manipulator tip (width: 400 μm) on the reference trajectory. Following the
horizontal and vertical lines is very stable. Moving in the diagonal direction is difficult because the x-axis motion and the y-axis
motion should be combined.
iii) Pick-and-place and 3D micro-assembly: assembling micro objects in 3-D is an advanced task. We prepared two kinds of
cubic micro objects, 1 mm-sized ones and 500 μm-sized ones (Leong et al., 2007; Pandey et al., 2013), and manipulated bigger
ones with the early version of the origami-based micromanipulation system (Yim et al., 2015). Multiple micro objects are
randomly distributed at the beginning, organized to one-by-four formation, two-by-two formation and finally four-by-one
formation.
iv) Micro separation and 3D micro-assembly: manipulating some of multiple micro objects without touching the rest ones is a
higher level demonstration because the untouchable objects become obstacles limiting the path of the grippers. The vertical
grippers in Fig. 16 are useful in this manipulation task because their small tips do not conflict other micro objects on the arena.
We set multiple micro objects in a small space (Fig. 24(a)). Assuming that the object A should not be touched during
Fig. 21. Straightness of the motions and the XY-orthogonality. The yellow lines present the tracked positions of the circle
centers, which are detected by using image processing techniques. (a) The z-axis motion. This shows extremely small
displacement of the circle center as a dot. (b) The x-axis motion (c) The y-axis motion (d) xy orthogonality. In all figures, the
white arrows indicate the moving direction of the circle centers.
-
manipulation, we picked up B between A and C (Fig. 24(b)), and placed it on A (Fig. 24(c)). Next, the object C is pushed to the
safe area by the tip (Fig. 24(d)). The stacked micro objects are hidden by the gripper, but not touched. In the safe area, we picked
up C (Fig. 24(f)), and place it on B again (Fig. 24(g-h)).
v) Origami-based compliant 3D grippers: unlike the laser-machined 2D grippers, the 3D origami grippers are very compliant
because they are made of a thin film (100 μm). They are passively deformed by the interaction with micro-object, so that they are
more appropriate for manipulating fragile or biological materials. In the experiments, the sharp tips go into the hollow surface of
the object. Technically, they are disadvantages when gripping a geometrically flat micro-object. However, the shape of the tips
could be adjusted according to the shape of the objects.
Fig. 22. 2D trajectory following experiments. Three letters, MIT, are the reference. The yellow line indicates the tracked
position of the manipulator tip.
Fig. 23. Pick-and-place and 3D assembly of multiple micro objects. (a) Micro objects are randomly distributed at the
beginning, (b) organized to one-by four formation, (c) two-by-two formation, and (d) finally four-by-one formation. The
time lapse are shown in the lower-right corners.
-
6. Discussion
This research contributes a rapid design and fabrication method for a low-cost high-performance micromanipulation system
employing three-dimensional origami technologies. We envision users downloading appropriate cut-and-crease patterns from
on-line stores, and rapidly prototyping a customized system using inexpensive off-the-shelf materials and a laser cutting machine.
The design is customizable to adjust the manipulation resolution (e.g., a few millimeters to tens of micrometer). Users can
Fig. 24. Delicate separation and 3D assembly of multiple micro objects (500 μm) using the vertical grippers. The time lapse
are shown in the lower-right corner. (a) Three micro objects are in the small space. The object A in the yellow box should not
be touched during manipulation. (b) Picking-up B between A and C. (c) Placing B on A. (d-e) Pushing C to a safe area with
the tip. (f) Picking up C. (g-h) Placing C on A and B.
Fig. 25. Picking up a 500 μm-size object with the compliant 3D grippers.
-
achieve different parameters for their specific applications by changing the combination of the syringes. The time required to
build the entire micromanipulation system is less than one hour.
The developed micromanipulation system shows a range of different high level micromanipulation abilities in experiments. In
the current version, however, operators cannot feel the hydraulic feedback force during the gripping motion yet because of two
reasons. First, the force transformation ratio is 0.27, so that operators can feel only a small part of the feedback force. Second, the
interaction force is lost by the deformation of the long cantilever of the gripper stage. A new design of the micromanipulation
system with hydraulic haptic feedback is the topic of the future research.
In this paper, we used a commercial microscope to view micro objects and their manipulation. In accordance with the printable
programmable robot paradigm, this system would be replaceable with a mobile smartphone with an attachable microscope lens.
Commercial micro scope lens for smart phones cost only 10 – 20 US dollars. Also, it is possible to manufacture the lens using a
drop of glue (or a transparent polymer) as studied in (Cybulski et al., 2014). The total cost of the current system excluding the
microscope is less than five US dollars for the current design, using current prices (Table 5).
Table 5. The bill-of-material of the origami-based paper-made micromanipulation system
Material unit price × number
Paper cardboard (L 500 mm × H 800 mm size) $2.3 × 1
Syringes $0.07 × 8
Magnet (D 12.3 mm × T 1.6 mm) $0.81 × 2
Total: $4.48
7. Conclusion
This paper presents the first low-cost (i.e., bill-of-materials smaller than five US dollars), high performance (i.e., capable of
doing pick-and-place, 3D micro assembly, and micro objects separation), precision (i.e., 0.25 – 0.96% straightness and 89.5 ±
0.96° xy orthogonality) origami-inspired tele-micromanipulation system. We described the critical origami structures, the
crease pattern design process, and the planar manufacturing methods for creating the system. Finally, we evaluated the
functionalities of the developed system in experiments. The current system is the result of multiple design modification
achieving a range of high level micromanipulation tasks. However, operators can improve (or modify) the proposed design
further according to their specific applications in addition to the useful origami structures that we proposed in this paper. The
working ranges and resolution are also customizable by changing the combination of syringes in the presented hydraulic motion
reduction system.
Acknowledgement
The authors would like to thank David H. Gracias and Shivendra Pandey for providing micro objects required for experimental
demonstrations.
Funding
This work was supported by the National Science Foundation, grant numbers 1240383 and 1138967
-
References
An B, Miyashita S, Tolley MT et al. (2014) An end-to-end approach to making self-folded 3D surface shapes by uniform
heating. In: Proc. of the 2014 IEEE International Conference on Robotics and Automation (ICRA), pp.1466-1473.
Bhattacharyya B, Doloi B, and Sridhar PS (2001) Electrochemical micro-machining: new possibilities for
micro-manufacturing. Journal of materials processing Technology 113(1): 301-305.
Boeckx W (1976) Clinical micro-surgery. Micro-surgery. Experimental techniques in the rat and clinical applications.
European Press, Ghent, Belgium, 192-194.
Caron AW, Massie B, and Mosser DD (2000) Use of a micromanipulator for high-efficiency cloning of cells co-expressing
fluorescent proteins. Methods in cell science 22(2): 137-145.
Causa F, Netti PA, and Ambrosio L (2007) A multi-functional scaffold for tissue regeneration: the need to engineer a tissue
analogue. Biomaterials 28(34): 5093-5099.
Cybulski JS, Clements J, and Prakash M (2014) Foldscope: origami-based paper microscope. PLoS ONE 9(6), e98781.
Felton S, Tolley MT, Demaine E et al. (2014) A method for building self-folding machines. Science 345(6197): 644–646.
Felton SM, Tolley MT, Onal CD et al. (2013) Robot self-assembly by folding: A printed inchworm robot. In: Proc. of IEEE
International Conference on Robotics and Automation (ICRA), pp.277-282.
Gauthier M and Piat E (2006) Control of a particular micro-macro positioning system applied to cell micromanipulation. IEEE
Transactions on Automation Science and Engineering 3(3): 264-271.
Hale LC (1999) Principles and techniques for designing precision machines. Ph.D. dissertation, Massachusetts Institute of
Technology.
Hawkes E, An B, Benbernou NM et al. (2010) Programmable matter by folding. Proceedings of the National Academy of
Sciences 107(28):12441-12445.
Hoover AM, and Fearing RS (2009) Analysis of off-axis performance of compliant mechanisms with applications to mobile
millirobot design. In: Proc. of IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp.2770-2776.
Inoue K, Arai T, Tanikawa T et al. (2005) Dexterous micromanipulation supporting cell and tissue engineering. In: Proc. of
IEEE International Symposium on Micro-NanoMechatronics and Human Science, pp.197-202.
Kawase Y, Iwata T, Watanabe M et al. (2001) Application of the piezo-micromanipulator for injection of embryonic stem cells
into mouse blastocysts. Journal of the American Association for Laboratory Animal Science 40(2): 31-34.
Leong TG, Lester PA, Koh TL et al. (2007) Surface tension-driven self-folding polyhedral. Langmuir 23(17): 8747–8751.
Mehta A, Bezzo N, An B, et al. (2014) A design environment for the rapid specification and fabrication of printable robots. In:
Proc. 14th International Symposium on Experimental Robotics (ISER).
Mehta AM, Rus D, K. Mohta et al. (2013) A scripted printable quad-rotor: rapid design and fabrication of a folded MAV. In:
Proc. of the 16th International Symposium of Robotics Research (ISRR).
Miyashita S, Meeker L, Tolley MT et al. (2014) Self-folding miniature elastic electric device. Smart Materials and Structures
23(9).
Onal C, Wood RJ, and Rus D (2011) Towards printable robotics: origami-inspired planar fabrication of three-dimensional
mechanisms. In: Proc. of IEEE International Conference on Robotics and Automation (ICRA), pp.4608-4613.
Pandey S, Gultepe E, and Gracias DH (2013) Origami inspired self-assembly of patterned and reconfigurable particles. Journal
of Visualized Experiments (72).
Popa DO, and Stephanou HE (2004) Micro and mesoscale robotic assembly. Journal of manufacturing processes 6(1): 52-71.
-
Rebec GV, Langley PE, Pierce RC et al. (1993) A simple micromanipulator for multiple uses in freely moving rats:
electrophysiology, voltammetry, and simultaneous intracerebral infusions. Journal of neuroscience methods 47(1): 53-59.
Shimada E, Thompson JA, Yan J et al. (2000) Prototyping millirobots using dextrous microassembly and folding. In: Proc. of
ASME IMECE/DSCD.
Soltero DE, Julian BJ, Onal CD et al. (2013) A lightweight modular 12-dof print-and-fold hexapod. In: Proc. of IEEE/RSJ
International Conference on Intelligent Robots and Systems (IROS), pp.1465-1471.
Tabarés JC, MacLachlan RA, Ettensohn, CA et al. (2010) Cell micromanipulation with an active handheld micromanipulator.
In: Proc. of the Annual International Conference of the IEEE on Engineering in Medicine and Biology Society (EMBC), pp.
4363-4366.
Tan KK, and Ng SC (2001) Computer controlled piezo micromanipulation system for biomedical applications. Engineering
Science & Education Journal 10(6): 249-256.
Thompson JA, and Fearing RS (2001) Automating microassembly with ortho-tweezers and force sensing. In: Proc. of
IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pp. 1327-1334.
Tolley MT, Felton SM, Miyashita S et al. (2014) Self-folding Origami: shape memory composites activated by uniform heating.
Smart Materials and Structures 23(9), 094006.
Van Steirteghem A (1994) IVF and micromanipulation techniques for male-factor infertility. Current Opinion in Obstetrics
and Gynecology 6(2):173-177.
Yaşargil M (2006) Microsurgery: applied to neurosurgery. Thieme.
Yim S and Kim S (2015) Printable, foldable and wearable tele-micromanipulation device for micro-robotic application, In:
Proc. of IEEE International Conference on Robotics and Automation, to appear.