notes
TRANSCRIPT
CHAPTER 5 COMPRESSION MEMBER
CONTENTS: 5.1 Introduction 5.2 Critical Load 5.3 Euler’s Theory 5.4 Column Having Various Types of Supports 5.5 Secant Formula 5.6 Perry-Robertson Formula 5.7 Rankine-Gordon Formula
5.1 Introduction Column = vertical member carries compressive axial loads. Sometimes, the compressive axial load is applied at the centroid and offset from
centroid. P1 P2
P e1 e2 Axially loaded column Eccentric column Type of columns;
a) short column = when the dimensional x-section is not very large as compared to its height. It fails due to ‘crushing’ of column material.
P P
CRUSH
P
CRUSH
P
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
1
b) long/slender column = when the dimension x-section is very large as compared to its height. It fails due to ‘buckling’.
P P 5.2 Critical Load
Assume the column is pinned at both support; P Pcr L Pcr P
For the beginning, the column is considered as an ideal column :perfectly straight before loading.
When the load,P is increasing until failure occurs by fracture/yielding. When the critical load, Pcr is reached, the column is becoming unstable. Any additional loading will cause the column to buckle and therefore deflect
laterally as shown above. Ideal column = is initially perfectly straight, made of homogeneous material and the load is applied through the centroid of the cross section.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
2
Critical load, Pcr = the maximum load that a column can support when it is on the verge of buckling. This loading represents a case of neutral equilibrium. To illustrate the phenomenon of buckling, the concept of stability is applied. 5.3 Euler’s Theory
Developed by the Swiss mathematician Leonard Euler on 1757 Initially developed for slender column
Column with pinned-ended support; Assumptions; 1) column is perfectly straight 2) load,P is applied exactly at the centroid of column 3) no lateral loads act along the height of column 4) material behaves within elastic region or ideal rigid-plastic or elastic-plastic
behaviour P P L y M x x
y
P P P Assume when the column is pinned support; Applying Theory of Bending;
Pydx
ydEI
Mdx
ydEI
curvaturedx
ydR
butREIM
yRE
IM
−=
=
===
==
2
2
2
2
2
21
σ
Cut any distance with x vertically; = M + Py M = -Py
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
3
)1(..........0
...
22
2
22
2
=+
=−
=
ydx
yd
EIPlet
EIPy
dxyd
α
α
Solve the equation (1) by using ‘complementary function’; )2.(..........sincos xBxAy αα += Applying the boundary condition;
a) y = 0 and x = 0 into (2);
0 = A + 0 A= 0 …. substitute A into (2)
b) y = 0 and x = L into (2);
Sine graph (column started buckle at sin π =0) +1 0 90 180 270 360 (ºdegree) -1 ..)3,2,1(
....)3,2,0(sin0sin
sin00
sincos
==
===
+=
+=
nnL
LwhenLLB
LB
xBxAy
πα
πππααα
α
αα
from substituteEIP
=2α πα nL =
2
22
2
22
LEInP
Ln
EIP
Ln
EIP
nxLEIP
π
π
π
π
=
=
=
=
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
4
n=1 n=2 n=3
Buckle shape that might be happened
Pcr = π2 EI if n =1 L2
where; Pcr = critical or maximum axial load on the column just before it begins to buckle. This load must not cause the stress in the column to exceed the proportional limit. E = modulus of elasticity for the material I = least moment of inertia (the weakest axis) for the column’s cross sectional
area. L = unsupported length of the column, whose ends are pinned
For purpose of design; from equation
Pcr = π2 EI …….(1) L2
2
22
2
22
2
)(
);1()3()2(
)3......()2....(
LEr
AP
LArEP
andSubstitute
ArIandA
P
cr
cr
crcr
π
π
σ
=
=
⇒
==
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
5
2
2
)( rL
Ecr
πσ =
……… (L/r) - slenderness ratio, buckling will occur about the axis when the ratio gives the greatest value.
- measurement of the column’s flexibility
where; σcr = critical stress which is an average stress in the column just before the column buckles. This stress is an elastic stress, σcr ≤ σy , (σy = yield stress of material) E = modulus of elasticity of material L = unsupported length of the column whose ends are pinned
r = radius of gyration determined from AIr = , where I is the least moment of
inertia of the column’s cross sectional area, A.
Euler’s formula can be used to determine the buckling load since the stress in the column remains elastic.
It is also important to realize the column will buckle about the principal axis of the cross section having the least moment of inertia (the weakest axis).
Allowable/Safety Load = SafetyofFactor
PLoadCritical cr )(
From σcr ≤ σy; The graph below is used to identify the (L/r) for the column made of a structural steel.
σcr(103)MPa
The graph used to represent the sritical stress versus the slenderness ratio. The curve is hyperbolic and valid only for critical stress below the material’s yield point. The yield stress of steel; (σy )s=250MPa (Es = 200GPa) From the curve,the smallest acceptable slenderness ratio (L/r)s = 89
250 Structural steel (σy = 250MPa) 89 L/r
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
6
For a steel column if (L/r)s ≥ 89 , Euler’s formula can be used to determine the buckling load since the stress in the column remains elastic. But if the (L/r)s < 89, the column’s stress will exceed the yield point and the Euler formula is not valid in this case.
Or the slenderness ratio can be determined from this equation;
8910250
)10200(
)(
6
92
2
2
2
==
=
=
xx
ErL
rL
E
cr
cr
π
σπ
πσ
EXAMPLE 5.1 A 7.2m long of steel tube having the cross section shown in figure is to be used as a pin-ended column. Determine the maximum axial load the column can support so that it does not buckle. Check whether the Euler’s formula is appropriate or not by using the condition σcr ≤ σy .Given Es = 200GPa, MPay 250=σ . Pcr 75mm 70mm Pcr
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
7
Solution; 1st Step: Identify the type of support.
[ ]
46
46
44
44
106
106
707541
41@
64
mx
mmx
rdI
−=
=
−=
=
π
ππ
kN
xx
LEIPcr
5.2282.7
)106)(10200(2
692
2
2
=
=
=
−π
π
2nd Step: Check whether the Euler’s equation is appropriate or not;
MPaxx
APcr
cr 2.1001028.2105.228
3
3
=== −σ
Since MPaMPawhereycr 2502.100 << σσ
(23
22
2
1028.2
14.015.04
4
mx
dA
−=
−=
=
π
π
So, Euler’s equation is appropriate. The maximum axial load= 228.5kN
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
8
EXAMPLE 5.2 The steel with the size W200 x 46 shown in figure is to be used as a pin-connected at the both ends. Determine the largest axial load it can support before it either begins to buckle or the steel yields. Check whether the Euler’s formula is appropriate or not by using the condition σcr ≤ σy .Given Es = 200GPa, MPay 250=σ .
Solution; From Appendix;
46
46
2
103.15
105.455890
mmxI
mmxImmA
y
x
=
=
=
By inspection, the column will buckle about the principal axis of the cross section having the least moment of inertia. From the given I, Iy-y is the lowest moment of inertia. The column will buckle at this axis. Take 46103.15 mmxI y =
kN
xx
LEIPcr
1.18884
)1053.1)(10200(2
592
2
2
=
=
=
−π
π
………..For the pinned-ended support
Check whether the Euler’s equation is appropriate or not;
.6.320/6.3205890
101.1888 23
MPaormmNxA
Pcrcr ===σ
As we know, the yield stress of steel is MPay 250=σ . The rule of Euler’s equation is σcr ≤ σy.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
9
From the calculation, it shows that σcr > σy where 320.6MPa > 250MPa. The stress exceeds the yield stress. Application of Euler’s equation is not appropriate. Use σy =250MPa to determine the new axial load.
kNPxPx
APcr
cr
5.1472105890
10250 66
=
=
=
−
σ
EXAMPLE 5.3 A steel column has a length of 9m and pinned at both ends. If the cross sectional area has the dimensions shown in figure, determine the critical load. Check whether the Euler’s formula is appropriate or not by using the condition σcr ≤ σy .Given Es = 200GPa,
MPay 250=σ .
10 150
200 10
10
Solution; The cross section is symmetry due to the same dimensions. Centroid or neutral axis is
.)85,100(, mmyx =
d1
d2
1
3
2
x
y
85=y
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
10
PART
AREA(mm2) Ix =
12
3bh
(103) (mm4)
d
(mm)
Ad2(103)(mm4)
1 200(10)=2000 12
)10(200 3
=16.67
85-5= 80
12800
2
150(10)=1500 12
)150(10 3
=2812.5
0 0
3
200(10)=2000 12
)10(200 3
=16.67
80 12800
=∑ xxI [Ix + Ad2]1 + [Ix + Ad2]2 +[Ix + Ad2]3
= [(16.67 + 12800)x2 + 2812.5] x103
= 28.45 x106 mm4
PART
AREA(mm2) Iy =
12
3hb
(103) (mm4)
s
(mm)
As2(103)(mm4)
1 200(10)=2000 12
)10(2003
=6666.67
0 0
2
150(10)=1500 12
)150(103
=12.5
0 0
3
200(10)=2000 12
)10(2003
=6666.67
0 0
=∑ yyI [Ix + As2]1 + [Ix + As2]2 +[Ix + As2]3
= [6666.67+12.5+6666.67] x103
= 13.35 x106 mm4
To determine the critical load, pick the value of lowest I=13.35 x106 mm4
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
11
kN
xx
LEIPcr
63.3269
)1034.1)(10200(2
592
2
2
=
=
=
−π
π
………..For the pinned-ended support
Check whether the Euler’s equation is appropriate or not;
.4.59/4.595500
101.63.326 23
MPaormmNxA
Pcrcr ===σ
As we know, the yield stress of steel is MPay 250=σ . The rule of Euler’s equation is σcr ≤ σy where 59.4MPa <250MPa.
The application of Euler’s equation is appropriate.
The critical load = 326.63kN.
EXERCISE 5.1 The pinned ended column is shown in figure. Determine;
a) whether the column is slender or not by using the slenderness ratio of slender column >100. Given E=200 kN/mm2 and factor of safety=2.0.
b) the allowable load for the column.
10 96
84 6m
20
20
(all units in mm) [Ans : L/r > 100 = slender column, allowable load = 54.4kN]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
12
EXERCISE 5.2 The 4m steel pipe column has an outer diameter of 75mm and a thickness of 6mm.
a) Determine the critical load if the ends are assumed to be pin connected. b) Check whether the Euler’s formula is appropriate or not by using the
condition σcr ≤ σy .Given Es = 210GPa, MPay 250=σ .
[Ans : Pcr = 101.1kN]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
13
5.4 Column Having Various Types of Supports
In the previous section, we derived the Euler load for a column that is pin connected of free to rotate at its ends. However, column may be supported in some other way with the different type of supports. Cantilever supports EXAMPLE 5.4
P P P δ δ y y Mx L L P
The diagram shows the column is fixed at its base and free at the top. The internal moment at arbitrary section is Mx = P(δ – y). Prove the critical load occurs at the column is Pcr = π2 EI .
4L2
Solution;
)(
)(
2
2
2
2
yPdx
ydEI
Mdx
ydEI
yPM
x
X
−=
=
−+−=
δ
δ
EIPy
EIP
dxyd
−=δ
2
2
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
14
)1(..........
.....
222
2
22
2
δαα
αδ
=+
==+
ydx
yd
EIPlet
EIP
EIPy
dxyd
Solve the equation (1) by using ‘complementary function’; )2.(..........sincos δαα ++= xBxAy Applying the boundary condition;
a) x = 0 and y = 0 into (2);
0 = A + 0 + δ A= -δ …. substitute A into (2)
b) x = 0 and dxdy = 0 into (2);
0000
cossin
=
=+=
+−=
BB
B
xBxAdxdy
αα
αααα
A= -δ and B=0, substitute into (2); )2.(..........sincos δαα ++= xBxAy δαδ +−= xy cos Since the deflection occur at the top of the column;
At x = L, y = δ cosines graph (column started buckle at sin 0.5π =0) +1
-90 0 90 180 270 360 (ºdegree)
-1 cos 0.5π, 1.5 π, 2.5π = 0
δαδδ +−= Lcos Lαδ cos0 −= Lαδ cos0 = Lαcos0 =
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
15
Known that EIP
=2α or EIP
=α
2
2
2
4
2
2
2
LEIP
LEIP
LEIP
xLEIP
π
π
π
π
=
⎟⎠⎞
⎜⎝⎛=
=
=
…. Its proven
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
16
Table 5: Effect of support conditions
Pinned-pinned Fixed-fixed Cantilever Fixed-pinned
Le
Basic Formula
2
2
ecr L
EIP π=
Le
L
0.5L
2L
0.7L
Pcr
2
2
)(LEIPcr
π= 2
2
)5.0( LEIPcr
π= 2
2
)2( LEIPcr
π= 2
2
)7.0( LEIPcr
π=
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
17
EXERCISE 5.3 The steel with size W310-129 has a length of 4m. If its bottom end is fixed supported while its top is free,
a) determine the effective length of column b) the slenderness ratio c) the allowable axial load it can support. Use a factor of safety with respect to
buckling of 1.75. Given Es = 210GPa, MPay 250=σ .
[Ans: Pallow = 1850.44kN] P
EXAMPLE 5.5 The aluminum column is fixed at its bottom and is braced at its top by cables in order to prevent movement at the top along x axis. If it is assumed to be fixed at its base; a) Check whether the Euler’s formula is appropriate or not by using the condition σcr ≤
σy . b) Determine the largest allowable load, P that can be applied. Use a factor of safety for buckling = 3.0. Given Eal = 70GPa, σy=215MPa, A = 7.5(10-3) m2, Ix = 61.3 (10-6) m4, Iy = 23.2(10-6) m4.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
18
Solution; Due to this condition of bracing, the column will buckle with different axis namely are x and y axis. In y axis, the column will behave as the fixed at its bottom and pinned at the
top end. So, the critical load is 2
2
)7.0( LEIPcr
π= .
kN
xxx
LEIPcr
8.1308
)57.0()102.23)(1070(
)7.0(
2
692
2
2
=
=
=
−π
π
In x axis, the column will behave as the fixed at its bottom and free at the top end. So, the
critical load is 2
2
)2( LEIPcr
π= .
kN
xxx
LEIPcr
6.423
)52()103.61)(1070(
)2(
2
692
2
2
=
=
=
−π
π
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
19
By comparison the column will buckle to the lowest P which is x axis. Pcr = 423.6kN a) And check whether the Euler’s equation is appropriate or not;
MPaA
Pcrcr 48.56
)10(5.7)10(6.423
3
3
=== −σ
Given, the yield stress of aluminum is MPay 250=σ . The rule of Euler’s equation is σcr ≤ σy where 56.48MPa < 215MPa. The application of Euler’s equation is appropriate. b)
The allowable load is; kNxSOF
PP crallow 2.141
3106.423
..
3
===
The critical load = 423.6kN The allowable load = 141.2kN
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
20
5.5 Secant Formula
The Euler formula was derived with the assumption; i) the load,P is always applied through the centroid of the column’s cross
sectional area and; ii) the column is perfectly straight.
This is actually quite unrealistic since manufactured columns are never perfectly straight. In actual condition, column never suddenly buckle, instead they begin to bend slightly upon the application of the load. The actual criterion for load application will be limited either to a specified deflection of the column or by not allowing the maximum stress exceed the allowable stress in the column. To investigate this effect load, P is applied to the column at a short eccentric distance, e from the centroid of the cross section.
Ly y
y
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
21
From Theory of Bending;
Mdx
ydEI
curvaturedx
ydR
butREIM
yRE
IM
=
===
==
2
2
2
21
σ
From figure above, internal moment column is;
)1..(..........
.....
)(
)(
)(
222
2
22
2
2
2
2
2
2
2
eydx
yd
EIP
EIPe
EIPy
dxyd
EIPy
EIPe
dxyd
yeEI
Pdx
yd
yePdx
ydEI
yePM
αα
α
−=+
=−=+
−−
=
+−
=
+−=
+−=
Solve the equation (1) by using ‘complementary function’; )2.(..........sincos exBxAy −+= αα
where A and B are constants and can be determined by using boundary condition.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
22
Applying the boundary condition; a) y = 0 and x = 0 into (2)
0 = A + 0 - e A= e subs A into (2)
)4.......(cossin
)3.(..........sincos
xBxedxdy
exBxey
αααα
αα
+−=
−+=
b) 0=== θslopedxdy and x = L/2 into (4)
)5....(..........2
tan
tancossin
cossin
cossin)4(
⎟⎠⎞
⎜⎝⎛=
==
=
+−=→
Le
xexxeB
xBxe
xBxedxdyFrom
α
ααα
αααα
αααα
Substitute (5) into (3);
)6.(..........sin2
tancos
sincos
exLexe
exBxey
−⎟⎠⎞
⎜⎝⎛+=
−+=
ααα
αα
Equation (6) is a general equation to find deflection anywhere within the column height. But there will be one position, y becomes maximum.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
23
For this pin-ended column, ymax ocuurs at mid-height;
At x = L/2 into (6)
)7..(..........12
sec
2sin
2tan
2cos
sin2
tancos)6(
max
⎥⎦
⎤⎢⎣
⎡−⎟
⎠⎞
⎜⎝⎛=
−⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎠⎞
⎜⎝⎛
⎟⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛=
−⎟⎠⎞
⎜⎝⎛+=→
Le
eLLeLey
exLexeyFrom
α
ααα
ααα
P M=P.e ymax M=P.e P deflection max occurs at x = L/2
Resubstitute EIP
=2α into (7);
)8.......(12
.sec
12
secmax
⎥⎦
⎤⎢⎣
⎡−=
⎥⎦
⎤⎢⎣
⎡ −⎟⎠⎞
⎜⎝⎛=
LEIPe
Ley α
Equation (8) indicates that ymax infinite when 22π
=EIPL
While deflection does not actually become infinite and nevertheless becomes unacceptably large. P should not be allowed to reach the critical value, Pcr.
For this support condition;
2
2
2
2
π
π
LPEI
LEIP
cr
cr
=
=
…into (8)
ymax ⎥⎦
⎤⎢⎣
⎡−= 1
2sec
crPPe π …….(9)
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
24
To find maximum stress; σmax
The column will reached compressive stress and σmax occurs when moment is maximum;
y
)(
)(
maxmax yePM
yePM
+=
+=
Substitute equation (8) into Mmax;
)10(..........2
.sec
12
.sec1
12
.secmax
⎟⎟⎠
⎞⎜⎜⎝
⎛=
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−+=
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛−+=
LEIPPe
LEIPPe
LEIPeePM
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
25
From Theory of Bending;
)11.........(2
sec.1
2.sec.
112
.sec.
2.sec.
.
2
2
222
maxmax
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛+=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
=⎟⎟⎠
⎞⎜⎜⎝
⎛+=
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
+=
EAP
rL
rye
AP
rL
EAP
AryPe
AP
rrthatknownL
AErP
AryPe
AP
LEIP
IyPe
AP
IyM
APσ
ArI 2=
where; σmax = maximum elastic stress in the column which occurs at the inner concave
side at the column’s midpoint. This stress is compressive. P = vertical load applied to the column. P < Pcr unless e = 0, then P = Pcr. e = eccentricity of the load P measured from the neutral axis of the column’s
cross sectional area to the line of P action.
y = distance from the neutral axis to the outer fiber of the column where the maximum compressive stress σmax occurs.
A = cross sectional area of the column. L = unsupported length of the column. For supports other than pins, the
effective length Le should be used.
E = modulus of elasticity for the material. r = radius of gyration, AIr /= where I is computed about the neutral or
bending axis.
2rey = eccentricity ratio
⎟⎟⎠
⎞⎜⎜⎝
⎛EAP
rL2
= Euler angle
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
26
Summary of Secant Formula Maximum Deflection;
⎥⎦
⎤⎢⎣
⎡−= 1
2.secmaxL
EIPey
y Maximum Stress;
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛+=
EAP
rL
rye
AP
2sec.1 2maxσ
EXAMPLE 5.6 The steel column shown in figure is assumed to be pin connected at its top and base.
a) Determine the allowable eccentric load, P that can be applied. Due to bracing assume buckling does not occur about the y axis.
b) Determine the maximum stress and deflection of the column due to this loading.
Given Es = 200 GPa and MPay 250=σ . z
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
27
Solution;
a) Determine the allowable eccentric load, P that can be applied.
y 50mm x 150mm
4633
4633
1056.112
)150(5012
1006.1412
)150(5012
mmxhbI
mmxbhI
y
x
===
===
A = 50(150) = 7500 mm2
e = 25mm
Refer to the question; Due to bracing assume buckling does not occur about the y axis. Take Ix.
mmxr 3.437500
1006.14 6
==
In the secant formula, the curves has been established for Es = 200 GPa and
MPay 250=σ , this curves can be used to determine the value of P/A to avoid a trial and error solution of the secant formula. From the curves L/r is the slenderness ratio and the type of support is pinned connected at the both ends, L/r is 4500/43.3 = 104. If the type of support is cantilever L/r will become as 2L/r and so on. y is the distance from the neutral axis to the outer fiber of the column where the maximum compressive stress occurs. So, the distance is 75mm.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
28
1.02 =rey
02 =rey
Using the curves, the eccentricity ratio, 13.43
)75(2522 ==
rey
The value of P/A approximate to be,
MPaAP 83≈
P = 83(7500) = 622.5kN
The allowable eccentric load, P = 622.5kN
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
29
b) the maximum stress and deflection of the column due to this loading.
To calculate the maximum stress, σmax;
( )[ ]
( )[ ]2
3
3
2
3
2max
/3.252
65.60sec1183
0585.1sec1183
7500)10200()10(5.622
)3.43(24500sec
3.43)75(251
7500)10(5.622
2sec.1
mmN
rad
x
EAP
rL
rye
AP
=
°+=
+=
⎥⎥⎦
⎤
⎢⎢⎣
⎡
⎟⎟⎠
⎞⎜⎜⎝
⎛+=
⎥⎥⎦
⎤
⎢⎢⎣
⎡⎟⎟⎠
⎞⎜⎜⎝
⎛+=σ
°= 64.601800585.1π
x
σy > σmax where 250MPa > 252.3 MPa Use σy =250 MPa because σmax can not be exceed than σy
To calculate the maximum deflection, ; maxy
[ ]
mm
rad
xx
LEIPey
26
)165.60(sec25
10585.1sec25
12
4500.)1006.14)(10200(
)10(5.622sec25
12
.sec
63
3
max
=
−°=
−=
⎥⎥⎦
⎤
⎢⎢⎣
⎡−=
⎥⎦
⎤⎢⎣
⎡−=
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
30
EXERCISE 5.4 The steel column shown in figure below is assumed to be pin-connected at its base and top. a) Determine the allowable eccentric load, P that can be applied. b) Calculate the maximum deflection of the column due to this loading?
Due to bracing, assume buckling does not occur about the y-axis. Take E=200(103) MPa and σy=250MPa.
C,centroid P
30mm
4.5m
60mm
120mm
[Ans: Peccentric = 360kN, ymax = 28mm]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
31
5.6 Perry-Robertson Formula
The formula used for structural steelwork is the Perry-Robertson formula that represented as the average end stress to cause yield in a strut.
where; σp = stress based on Perry-Robertson formula. σE = Euler’s stress σyield = yield stress depending on the yield strength of material η = constant depending on the material. For a brittle material η = 0.015L/r, for
a ductile material η = 0.3 (L/100r)2
5.7 Rankine-Gordon Formula
2)/(1 rLay
R +=
σσ
where E
a y2πσ
= theoretically but is usually found by experiment. Typical values are :
a
Material Compressive yield stress (MN/m2) Pinned ends Fixed ends
Mild steel 315 1/7500 1/30000 Cast iron 540 1/1600 1/6400 Timber 35 1/3000 1/12000
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
32
Appendix A
American Standard Channels or C Shapes
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
33
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
34
TUTORIAL 5
1. A steel column has a length of 9m and is fixed at its bottom and free at its top. If the cross-sectional area has the dimensions shown; a) determine the critical load. b) also check whether the Euler’s Equation is appropriate or not. Given Est= 200GPa,
σy= 250 MPa.
200mm 10mm 10mm 150mm 10mm [Ans: a) Pcr = 82.25kN, b) σcr = 14.95MPa] 2. a) The 4m steel column has an outer diameter of 80mm and a thickness of
6mm. Determines the critical load if the bottom is fixed and the top are pinned. Also check whether the Euler’s Equation is appropriate or not. Given E= 210GPa, σy= 250 MPa.
b) A steel strut is 6.5m long and constructed from circular tube with an outside
diameter of 120mm as shown in figure below. The type of strut is fixed at the bottom and pinned at the top. The strut must resist an axial load of 150kN from buckling. Using a factor of safety of 2.0, determine the required tube thickness and the critical buckling stress. Given E = 200GPa.
[Ans: a) Pcr = 254kN, σcr = 183MPa, b) t = 5.3mm, σcr = 157MPa]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
35
3. The steel angle has a cross sectional area of 1550mm2. A radius of gyration about the x axis is 32mm and about y axis is 22mm. The smallest radius of gyration occurs about z axis is 16mm. If the angle is to be used as a pin-connected with 3m long column, determine the largest axial load that can be applied through its centroid, C without causing it to buckle, E= 200GPa.
y z x C x y z [Ans: Pcr =87.03kN] 4. a) Define the following terms;
i. short column ii. slender column
iii. Euler buckling load
b) List 5 assumptions or limitation of Euler’s formula. c) A column is 8m high and is constructed from circular hollow section as shown in
figure. The column is fixed at one end and is free at the other end. Determine the critical buckling load. Given E = 2x105 N/mm2.
[Ans: c) Pcr = 36.86kN]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
36
5. a) The 4m steel pipe column has an outer diameter of 100mm and a thickness of 8mm. Determine the critical load if the ends are assumed to be pin connected. Also check whether the Euler’s Equation is appropriate or not. Given E=210GPa , σy=250MPa.
b) Determine the Euler’s buckling load for an I-section of a column as shown in
figure with length of 10m and fixed at both ends. Given E = 200GPa.
[Ans: a) Pcr = 19.31kN, σcr = 138.8MPa, b) Pcr = 459kN]
6. For the column fixed at the base and the top,
Mx
MP
Cut section y L
P M
P
L
P
Cut any section vertically.
M The internal moment at arbitrary section is;
. MPyMMPyM
x
x
+−=−+=
The critical load acted is 2
24L
EIPcrπ
= . Prove the equation.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
37
7. a) Write the relationship between Euler’s buckling stress with slenderness ratio. b) If a pin-ended solid circular strut is 3m long and 60mm diameter, determine the
strut’s slenderness ratio. c) If the same material on 7(b) is reshaped into a square bar with the length and same
width of 60mm, determine the percentage reduction in the slenderness ratio. [Ans: b) L/r = 200, c) 13.4%]
8. A steel strut with total length of 5m is constructed of circular tube. The dimension of tube is diameter, Doutside = 100mm and thickness t = 12mm. The type of strut is partially restrained which is fixed at the bottom and pinned at the top. Determine;
a) slenderness ratio. b) Euler buckling load. c) ratio of axial stress under the action of the buckling load to the elastic
strength of the material. Given E=200GPa , σy=250MPa. d) safety load the column can support with a factor of safety of 1.5.
[Ans: a) L/r = 111.46, b) Pcr = 527kN, c) 0.635, d) Pallow = 351.3kN] 9. a) For a pin-ended solid rectangular column with a dimension 120cm x 50cm and
5m in length. Given E = 200GPa. Determine; i. slenderness ratios at both axes.
ii. Euler’s buckling load. iii. allowable load with a factor of safety of 2.5.
b) Determine the Euler’s buckling load for an I-section of length 6m when fixed at
both ends as shown in figure.
[Ans: a) i) (L/r)x = 34.65, (L/r)y = 14.43, ii) Pcr = 987MN, iii) Pallow =394.5MN, b) Pcr =26.4MN]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
38
10. a) State all Euler’s buckling load formulas for different end support conditions. b) Determine the Euler’s buckling load for a C-section of column as shown in figure
with length of 10m and fixed at both ends. Given E = 200GPa.
[Ans: Pcr =436.63kN]
11. a) The cross sectional area of column which is fixed at the bottom and pinned at the top is shown in figure. The length of column is 1.5 meter. Given E = 200GPa. Determine;
i) slenderness ratio. ii) Euler’s buckling load. iii) the allowable load with a factor of safety of 2.5.
b) For a fixed and free ends column of length 2m with a cross section as shown in figure, determine;
i) slenderness ratio of the column. ii) Euler’s buckling load. iii) allowable load that the column can carry by assuming a factor of
safety is 2.5. Given E = 200GPa.
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
39
[Ans: a) i) L/r = 20.21, ii) Pcr = 200.13MN, iii) Pallow =80MN, b) i) L/r = 128, ii) Pcr = 414.5kN, iii) Pallow = 165.8kN] 12. a) A steel column has a hollow circular cross sectional area with an outside
diameter of 120mm and inside diameter of 100mm. The column is 6.0m length and is pin ended at both ends. Given E = 200GPa. Determine;
i. slenderness ratio ii. Euler’s Buckling load iii. Axial stress in the column when the column is subjected to the
Euler’s Buckling load.
b) The cross sectional area of the column given in 12(a) is reshaped with the new radius of gyration r = 39.9mm and area = 11 355mm2. Determine the current value of slenderness ratio, Euler Buckling load and axial stress.
c) A column of 3m height has a cross section as shown in figure. Both of its
end are fixed. Determine the safe load when a factor of safety equals to four. Check whether the Euler’s Equation is appropriate or not. Given E= 200GPa, σy= 250 MPa.
[Ans: a) i) L/r = 153.8, ii) Pcr = 288.96kN, iii) σcr = 83.6MPa,
b) i) L/r = 150.4, ii) Pcr = 992.4kN, iii) Pallow = 87.4MPa]
____________________________________________________________________________________________ BFC 2083-Mechanic of Materials
40