WALL CARE PUTTY

VIJAYWHITE

Vijay White Wall Care Putty is a specially formulated powder putty with unique

raw materials & additives.

1 Kg 20 Kg 40 KgPACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White lump-free powderDrying time Initial = 40 – 60 min Final = 4 – 6 hoursPot Life ofthinned material 1 – 1.5 hours Tensile adhesion > 1.0 N/mm2 after 28 days

Water retentivity > 98% Tapped density 1.5 – 1.7 g/ccRecoatability 2 – 3 hoursUSESInterior & Exterior plastered surfacesI concrete, rendered wall, hollow block, precast walls, concrete ceilings,aerated light-weight blocks.BENEFITSExcellent whiteness & smooth finishI Excellent workability and ease of application I Prevents water leakageI Prevents growth of algae and fungusI Provides ideal base for painting I Never peels off I Provides good breathabilityI Anti-flaking I No blisteringI No chalking I No curing required.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protectfrom direct sunlight.Recommended Dilution1st coat = 40% v/w dependingon surface conditions 2nd coat = 45 - 50% v/w dependingon surface conditions

COVERAGE2 sq.mtr / kg / 2 coats on well prepared substrate.DIRECTIONS OF USEClean the surface with emery paper,putty blade or wire brush. Moisten the wall with clean water. There should be no dirt, oil traces or algae on the surface I Mix the putty with 40 % water by volume to Vijay White to prepare a uniform paste. Add the water gradually. Stir the mix thoroughly to avoid formation of lumps. Let it rest for 10 minutes. Give the paste a good mix once more I Apply first coat of putty starting from the bottom of the wall in an upward direction uniformly using a putty knife I Allow it to dry for 2 -3 hours and then rib the surface gently with fine emery paper to remove loose particlesI Apply the second coat with fresh material and maintain the total thicknessof the two coats to about 1.5 mmI Allow it to dry for at least 10 – 12 hours.NOTENot recommended for paintedor non-cementitious surfacesI Ensure the material is mixedhomogenously with waterI Once the putty paste is hardened,it should not be softened by the additionof water and applied on the wall.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of waterI Keep out of reach of children.

M-Sand Boozter is a chloride-free, synthetic polymer-based cement enhancer which allows replacing river sand with M-Sand completely

for plastering, concrete and brick works.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquid Colour Dark brown Specific gravity @ 27°C 1.25 ± 0.05 Non-volatile content 35 ± 3 % pH 10 ± 3 USESCement brick works, cement plaster and cement concrete I Ready mix concrete, concrete piles, and precast concrete I Dams, bridges, tunnels, fly-overs, canals and sea shore projects I Foundations, floor slaps, walls, columns, beams, ceilings, balconies, etc I All slender components with heavy reinforcement.BENEFITSEffectively helps replace river sand I While plastering, smooth and ease of application by locking the pores I Increases in compressive strength and plasticity I Development of early strength, workability, slump retention and setting time I Reduction of cement content, cracks, creeps and shrinkage I Reduction of cost and time of construction and amount of labour required.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.ADVANTAGESDevelopment of early strength, workability, slump retention and setting time. I Reduction of cost and time for construction and the amount of labour required.RECOMMENDED DOSAGE200 ml / 50 kg of cement. DIRECTIONS OF USECement, sand and other aggregates are mixed with 90-95% of required water for 2-3 minutes I The recommended quantity of M-Sand Boozter is measured and added to the balance 5-10% of water and added to wet concrete I This mixture is mixed thoroughly for further 2-3 minutes to get a homogenous mix.NOTEDo not add M-Sand Boozter directly to dry mix I Maintain water-cement ratio as low as possible I Do not increase the dosage of M-Sand Boozter beyond the recommended level I Over dosage may lead to delay in setting time.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

M SAND BOOZTERM SAND LUBRICATOR

200 ml 1 Lt 5 Lt 20 Lt

SUPER PLASTICISER

Flow Faast is a chloride-free super plasticiser which allows mixing water to be reduced

considerably and enhances the concrete strength significantly, particularly at early stages.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Wine red/dark brownSpecific gravity @ 27°C 1.05 – 1.15Non-volatilecontent 15 ± 3 %ph 9-13Water reduction Max 20%USESReady mix concrete, concrete piles and precast concrete I Dams, bridges, tunnels, fly-overs, canals and sea shore projects I Foundations, floor slaps, walls, columns, beams, ceilings, balconies, etc I All slender components with heavy reinforcement.BENEFITSIncreases in compressive strength and plasticity I Reduces water to cement ratio by about 20% and significantly reduces water permeability I Development of early strength, workability, slump retention and setting time I Reduction of cement content, cracks, creeps and shrinkage I Reduction of cost and time of construction and amount of labour required I Provides faster mould release and increases bonding to reinforcement steels I Improvesflow up to 120 mm slump test.

SHELF LIFE & STORAGEBest before 12 monthsin an unopened, undamaged,originally sealed packing and if storedin dry conditions I Protectfrom direct sunlight.Recommended Dilution100 – 200 ml / 50 kg of cement.DIRECTIONS OF USECement, sand and other aggregates are mixed with 90-95% of required water for 2-3 minutesI The recommended quantityof Flow Faast is measured and addedto the balance 5-10% of water and added to wet concrete I This mixture is mixed thoroughly for further 2-3 minutes to get a homogenous mix.NOTEDo not add Flow Faast directly to dry mix I Maintain water-cementratio as low as possible I Do not increase the dosage of Flow Faast beyond the recommended level I Over dosage may lead to delay in setting time.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

FLOW FAAST

1 Lt 5 Lt 20 Lt

Veco Latex is a rubberised polymer, specifically designed for use with cement formulations,

in making cement modified coatings, polymer modified mortars and concrete.

PACKAGING

SUPER LATEX POLYMER

250 ml 500 ml 1 Lt 3 Lt 5 Lt

VECOLATEX

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquidColour Milky WhiteSpecific gravity @ 27°C 1.00 ± 0.10Non-volatile content 35.00 ± 3.00% pH range 8 – 10USESFor concrete repair, particularly those concrete structures which are damaged due to Corrosion of reinforcement I Bridge deck overlays and cement patching work I Waterproofing treatment I For bonding old to new concrete I As an admixture for making polymer modified mortar & concrete I For fixing tiles I Abrasion resistant and anti-corrosive floor.BENEFITSWaterproofing I Corrosion inhibition I Protects surface from attack of salty petre I Universal repair product.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGEWaterproofing 1 part Veco Latex : 4 or bonding coat part water : 6 part CementRepair, 1 part Veco Latex: 4 part plastering and Water : Cement & Sand sealing mortar as requiredAbrasion resistant Add 5 to 10% by weight flooring of cementDIRECTIONS OF USEThe surfaces must be be clean and free from oil, grease, dust, rust, etc I Prepare Veco Latex solution by mixing it with water. Add this mixture to the required cement and sand combination to prepare cement mortar, plastering, waterproofing / bond coat, putty I Dampen the surface and apply the Veco Latex modified cementitious mixture by brush or trowel I Cure by spraying water periodically for 2– 3 days.NOTEPrepared material must be usedwithin 30 minutes I Never add Veco Latex directly to cement.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Corrosolve is a corrosion inhibiting admixture for steel reinforced concrete.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Amber colourSpecific gravity @ 27°C 1.10 – 1.20 Non-volatile content 20 – 30%pH 7 – 8USESConventional steel reinforced concrete I Parking garage decks, bridge decks and marine structures.BENEFITSPenetrates concrete and protects the rebars from corrosion I Provides effective protection against corrosion by chlorides in concrete I Enhancing the life and strength of reinforced concrete I Environment friendly I Easy to use, neutral set liquid admixture.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packing and if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE100 ml Corrosolve for 1 bag (50 kg) cement.

DIRECTIONS OF USE Dry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 75% of required water and mix for 2-3 minutes I In the remaining portion of the required water add Corrosolve. Then add thisto concrete mixer and mix for another2-3 minutes for a homogenous mixI Flow Faast and Water Seal can be added to the mixture I Cure as per the normal procedure.NOTEDo not add Corrosolve directly to dry cement or aggregate mix I Do not increase the dosage of Corrosolve than the recommended level.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with water immediately after use I Cured material can be removed mechanically.

500ml 1 Lt 5 Lt 20 Lt

CORROSOLVERUST INHIBITOR ADMIXTURE

1 Lt 5 Lt 20 Lt

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquidColour Dark brownSpecific gravity @ 27°C 1.00 – 1.10Non-volatile content 8 – 12 % pH range 5 – 7BENEFITSTime-tested and traditional method I Cost effective I Avoids crack formation I Resists water leakage I Excellent resistance to all weather conditions I Enhances the strength of concrete roof.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packing

and if stored in dry conditionsI Protect from direct sunlight.RECOMMENDED DOSAGE1 litre / for 20 litre of water.DIRECTIONS OF USEThoroughly clean the roof surface I Add 1 litre Surki Bond to 20 litre water and mix well I Mix the Surki Bond solution with recommended cement or lime, sand, brick aggregates then spread over the surface. NOTEDo not add Surki Bond directly to dry cement or aggregate mix. HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Surki Bond is a traditional weatherproof admixture which is used along with sand, aggregates, cement

or lime wash in the concrete roofs.

PACKAGING

WEATHER PROOF ADMIXTURE

SURKI BOND

Tile Plus is a specially designed pleasant paint for Kollam and Mangaluru clay roofing tiles.

It is composed of advanced polymer ingredients and is a water-soluble

environmental friendly product.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSType Solvent based Colour As per customer requirement Specific gravity @ 27°C 1.00 ± 0.05 Non-volatile content 40.00 ± 5.00%Viscosity 100 - 200 cPFinish Rich Matt Touch dry 1 hourHard dry 8 hoursOver coating interval 4 – 6 hoursUSESKollam and Mangaluru clay roofing tiles I Exterior brick works.BENEFITSRich matt finish I Good hiding property I Allows the surface to breathe and expel moisture I Colour never faded I Algae and fungal resistance I Waterproofing I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE400 ml of water per litre of cement primer.COVERAGE80 – 90 sq.ft / litre / coat. DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Dampen the surface with water I Dilute with 40% of water by volume to Tile Plus and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours with brush/rollers I After 4 – 6 hours, apply another coat I Two coats are recommended.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with proper thinner or kerosene immediately after use.

1 Lt 4 Lt 10 Lt 20 Lt

TILEPLUS

A PLEASANT PAINT FOR ROOF TILES

500 ml 1 Lt 4 Lt

Shine-Tile is a paint composed of special polymers along with technically advanced ingredients in a unique formulation for providing a high

gloss, long lasting coating.

PACKAGING

SHINETILE

ROOF CLAY TILE POLISH PAINT

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSType Solvent based Colour As per customer requirement Specific gravity @ 27°C 1.00 ± 0.05 Non-volatile content 40.00 ± 5.00%Viscosity 100 - 200 cPFinish GlossyTouch dry 1 hourHard dry 8 hoursOver coating interval 4 – 6 hoursUSESKollam and Mangaluru clay roofing tiles I Exterior brick works.BENEFITSGlossy finish I UV resistance I Dust resistance I Colour never faded I Algae and fungal resistance I Water repellent property I Ideal for wood, metal & cement surfaces.SHELF LIFE & STORAGEBest before 24 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE2 Coats.COVERAGE100 – 120 sq.ft / litre / coat. DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Prime the surfaces with V-Repel water repellent primer I Apply a single coat and allow it to dry for about 4 – 6 hours with brush/rollers I After 4 – 6 hours, apply another coat I Two coats are recommended.NOTEDon’t thin the paint with any solvent I Never apply on wet/damp surfaces.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.CLEANING OF TOOLSClean all tools and application equipments with proper thinner or kerosene immediately after use. Cured material can be removed mechanically.

Gosana is a water-based emulsion composed of acrylic polymers and selected ingredients.

It is specially formulated to be used as floor paint, as an alternate for applying cow dung

on the floor, at the entrance of buildings.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth paste Colour Cow dung colour Specific gravity @ 27°C 1.40 ± 0.05 Non-volatile content 55.00 ± 5.00%Viscosity 3000 – 5000 cPpH 8.00 ± 1.00Finish Rich mattSurface dry 30 minutesOver coating interval 4 – 6 hoursStability of thinned paint 24 hours USESConcrete flooring I Artificial and natural stones.BENEFITSRich matt finish I Good hiding property I Abrasion resistance I Waterproofing & does not fade with weather I Very good intercoat adhesion I Can be applied by brush or rollers or spray I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE400 ml of water per litre of cement primer.COVERAGE60 – 70 sq.ft/ litre/ coat .DIRECTIONS OF USEFloor must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Application should start 4 hours after the application of Primer I Dilute with 40% of water by volume to Gosana and stir thoroughly to get homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

FLOOR PAINT

GOSANA

1 Lt 4 Lt 10 Lt 20 Lt

5 Kg

TOP COOL COAT

Solar Koat is a two component cooling coating for the roof which reduces the room temperature.

PACKAGING

SOLAR KOATPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance after mixing White, smooth pasteMix density 1.40±0.05pH 9.00±1.00Surface dry 30 minutes Over coating interval 6 hoursUSESTerraces, rooftops, parapet walls, lime terraced roofs, roof slabs I RCC, asbestos, sunshades I Exterior walls of buildings.BENEFITSIdeal for R.C.C. Asbestos, G.I. Sheets, exterior walls and pathways I Reduces power and water consumption of humidification plants I Prevents emission of highly polluting particles from asbestos sheets I Glass wool padding and false ceiling are eliminated I Cost effective.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

COVERAGE300 sq.ft / 5 kg bag / 2 coats.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Wet the surface enough prior to painting I Mix 125 ml of Solar Koat liquid into 8 litres of clean water I Add 5 kg of Solar Koat powder slowly and stir into the mixed solution I Apply the paint over the wet surface uniformly and allow it to dry completely I After 2-4 hours, apply another coat.NOTEDo not apply in hot sunlight (generally don’t paint between 10 a.m. to 5 p.m.) I Don’t mix the liquid directly to the powder I In a single shot, mix all the contents.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

COOL COATING & WATERPROOFING COATING

Surya Kavash is a single component acrylic based, microspheres enhanced waterproofing

roof coating which reduces the room temperature up to 8°C.

PACKAGING

SURYA KAVASHPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White, smooth pasteSpecific gravity @ 27°C 1.40±0.05Brookfield viscosity 20000 ± 3000 cPNon-volatile content 60 ± 2%pH 8.00±1.00Surface dry 30 minutesDFT per coat 80 – 90 micronsOver coating interval 6 hoursUSESTerraces, rooftops, parapet walls, lime terraced roofs, roof slabs I RCC, asbestos, sunshades & metal surfaces I Exterior coating for PVC water tanks placed in direct sunlight I Exterior walls of buildings.BENEFITSIdeal for R.C.C. Asbestos, Terracotta tiles, G.I. Sheets, Plastic tanks etc I Reduces power and water consumption of humidification plants I Prevents emission of highly polluting particles from asbestos sheets I Glass wool padding and false ceiling are eliminated I Acts as 100% waterproofing coating and prevents fungal & algae growth.

SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Repair holes and cracks with Vijay Crack-X / Tek Seal and prime the surface using Surya Kavash in 1:1 ratio with water I Dilute with 40% of water by volume to Surya Kavash and stir thoroughly to get homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEDo not apply in hot sunlight (generally don’t paint between 10 a.m. to 5 p.m.) I Primer and two coats are mandatory for durability of coating.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

1 Kg 5 Kg 20 Kg5 Kg

ROOF COOL COATING

Summer Coat is a two component cooling coating for the roof which reduces the room temperature.

PACKAGING

SUMMER COATPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance after mixing White, smooth pasteMix density 1.40±0.05pH 9.00±1.00Surface dry 30 minutes Over coating interval 6 hoursUSESTerraces, rooftops, parapet walls, lime terraced roofs, roof slabs I RCC, asbestos, sunshades I Exterior walls of buildings.BENEFITSIdeal for R.C.C. Asbestos, G.I. Sheets, exterior walls and pathways I Reduces power and water consumption of humidification plants I Prevents emission of highly polluting particles from asbestos sheets I Glass wool padding and false ceiling are eliminated I Cost effective.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

COVERAGE300 sq.ft / 5 kg bag / 2 coats.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Wet the surface enough prior to painting I Mix 125 ml of Summer Coat liquid into 8 litres of clean water I Add 5 kg of Summer Coat powder slowly and stir into the mixed solutionz I Apply the paint over the wet surface uniformly and allow it to dry completely I After 2-4 hours, apply another coat.NOTEDo not apply in hot sunlight (generally don’t paint between 10 a.m. to 5 p.m.) I Don’t mix the liquid directly to the powder I In a single shot, mix all the contents.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

ANTI HEAT CUMWATERPROOFING

Summer-eX is a single component acrylic based, microspheres enhanced waterproofing

roof coating which reduces the room temperature up to 8°C.

PACKAGING

SUMMER - eX

1 Kg 5 Kg 20 Kg

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White, smooth pasteSpecific gravity @ 27°C 1.40±0.05Brookfield viscosity 20000 ± 3000 cPNon-volatile content 60 ± 2%pH 8.00±1.00Surface dry 30 minutesDFT per coat 80 – 90 micronsOver coating interval 6 hoursUSESTerraces, rooftops, parapet walls, lime terraced roofs, roof slabs I RCC, asbestos, sunshades & metal surfaces I Exterior coating for PVC water tanks placed in direct sunlight I Exterior walls of buildings.BENEFITSIdeal for R.C.C. Asbestos, Terracotta tiles, G.I. Sheets, Plastic tanks etc I Reduces power and water consumption of humidification plants I Prevents emission of highly polluting particles from asbestos sheets I Glass wool padding and false ceiling are eliminated I Acts as 100% waterproofing coating and prevents fungal & algae growth.

SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Repair holes and cracks with Vijay Crack-X / Tek Seal and prime the surface using Summer-eX in 1:1 ratio with water I Dilute with 40% of water by volume to Surya Kavash and stir thoroughly to get homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEDo not apply in hot sunlight (generally don’t paint between 10 a.m. to 5 p.m.) I Primer and two coats are mandatory for durability of coating.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White, smooth pasteBrookfield viscosity 8000 ± 1000 cPSpecific gravity @ 27°C 1.00±0.05Non-volatile content 60±3% pH 8.00 – 10.00Surface dry 30 minutesDFT per coat 80 – 90 micronsOver coating interval 2-4 hoursUSESAsbestos, non-asbestos, sunshades, RCC, cement sheets I Terraces, rooftops, parapet walls, lime terraced roofs, roof slabs I Exterior & Interior walls of buildings. BENEFITSIdeal for R.C.C., asbestos, aon-asbestos, Cement sheets, etc I Reduces power and water consumption of humidification plants I Highly flexible film I Water vapour permeable (breathable) I Crack bridging I Prevents fungal & algae growth I Environment friendly.

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protectfrom direct sunlight.COVERAGE135 – 150 sq.ft / litre / coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, oil, wax, rust and loose or peeling paint before painting I Repair holes and cracks with Vijay Crack-X and prime the surface using M-Cool Primer in 1:1 ratio with water by brush or spray I Dilute with 40 - 50% of water by volume to M-Cool and stir thoroughly to get a homogenous mixture I Apply single coat by brush or spray and allow it to dry for about 2-4 hours I After 2-4 hours, apply second coat by brush or spray.NOTEDo not apply in hot, direct sunlight I Primer and two coats are mandatory for durability of coating.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

M-Cool is a innovative acrylic-based, newly designed, special additives enhanced,

ready-to-use flexible, sunlight reflection & thermal insulation coating

which reduces the room temperature up to 7 – 9°C at peak summer hours.

PACKAGING

ROOF COOL COATING

1 Lt 4 Lt 10 Lt 20 Lt

M COOLPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White, smooth pasteViscosity 25000 ± 2000 cPSpecific gravity @ 27°C 1.45±0.05Non-volatile content 50 – 60% pH 9.00±1.00Surface dry 30 minutesSheen level Soft sheenOver coating interval 2-4 hoursStability of thinned paint 24 hours

USESAsbestos, non-asbestos, brick work, gypsum boards I Cement plasters, concrete, cementitious renderings I False ceilings.BENEFITSSmooth finish I Good hiding property I Allows the surface to expel moisture I Breathable I Very good intercoat adhesion I Seals chalky surfaces, improves top coat adhesion & top coat area coverage I Free from heavy metals like mercury, lead and chromium.

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protectfrom direct sunlight.RECOMMENDED DILUTION1litre of water per litre of cement primer.COVERAGE110 – 120 sq.ft/litre/coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, oil, wax, rust and loose or peeling paint before painting I Repair holes and cracks with Vijay Crack-X I Add 1:1 of water and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours by brush or spray.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

M-Cool Primer is a water-based breathable primer suitable for interior & exterior sand

plastered surfaces, concrete and asbestos, etc specially designed as a primer coat prior

to Roof Cool Coatings.

PACKAGING

PRIMER FOR M-COOL

1 Lt 4 Lt 10 Lt 20 Lt

M COOL PRIMERPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Wine red/dark brown Specific gravity @ 27°C 1.05 – 1.07 Non-volatile content 11 – 15 % pH 8 – 12Setting time 30 – 600 minutesUSESBasements I Roof slaps and screeds I External plastering I Balconies and bathrooms I Water tanks, water retaining structures and terrace I Sumps and drains I Beams and columns I Repair works and renovation works.BENEFITSCompatible with all types of cements I Reduces the permeability of water into concrete and improves water tightness I No added chloride thus not contributing to corrosion of steel I Reduces capillary structures formed in concrete I Facilitates better workability without increased water content I Reduces shrinkage and thus avoid crack formation I Leads to better finish.

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE200 ml / 50 kg of cement.DIRECTIONS OF USEDry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 70-80% of required water and mix for 2-3 minutes I In the remaining portion of water add Water Seal IW. Add this to concrete mixer and mix for another 2-3 minutes for a homogenous mix I Place the concrete or apply plaster as per your need I Cure as per the normal procedure.NOTEDo not add Water Seal IW Plus directly to dry cement or aggregate mix I Do not increase the dosage of Water Seal IW Plus than the recommended level I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Water Seal IW Plus is an integral liquid waterproofing admixture for all types

of concrete, plaster and mortar.

PACKAGING

LIQUID WATERPROOFING ADMIXTURE

WATER SEALIW PLUS

100 ml 500 ml 1 Lt 2.5 Lt 5 Lt 20 Lt100 ml 500 ml 1 Lt 2.5 Lt 5 Lt 20 Lt

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Wine red/dark brown Specific gravity @ 27°C 1.05 – 1.07 Non-volatile content 12 – 15 % pH 9 – 12Setting time 30 – 600 minutesUSESBasements I Roof slaps and screeds I External plastering I Balconies and bathrooms I Water tanks, water retaining structures and terrace I Sumps and drains I Beams and columns I Repair and renovation works.BENEFITSCompatible with all types of cements I Reduces the permeability of water into concrete and improves water tightness I No added chloride thus not contributing to corrosion of steel I Reduces capillary structures formed in concrete I Facilitates better workability without increased water content I Reduces shrinkage and thus avoid crack formation I Leads to better finish.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE100 ml / 50 kg of cement.DIRECTIONS OF USEDry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 70-80% of required water and mix for 2-3 minutes I In the remaining portion of water add Water Seal. Then add this to concrete mixer and mix for another 2-3 minutes for a homogenous mix I Place the concrete or apply plaster as per your need I Cure as per the normal procedure.NOTEDo not add Water Seal directly to dry cement or aggregate mix I Do not increase the dosage of Water Seal beyond the recommended level I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Water Seal is an integral liquid waterproofing admixture for all types of concrete,

plaster and mortar.

PACKAGING

TRIPLE ACTION CEMENT WATER

PROOFING COMPOUND

WATERSEAL

TRIPLE ACTION CEMENT WATER PROOFING COMPOUND

1 kg box and 1 kg pouch

1 Kg

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Lump free powderColour Pale white Tapped density 1.50 ± 0.10 pH of 10% slurry 7 – 9Setting time 30 – 600 minutesUSESBasements I Roof slaps and screeds I External plastering I Balconies and bathrooms I Water tanks, water retaining structures and terrace I Sumps and drains I Beams and columns I Repair and renovation works.BENEFITSCompatible with all types of cements I Reduces the permeability of water into concrete and improves water tightness I No added chloride thus not contributing to corrosion of steel I Reduces capillary structures formed in concrete I Facilitates better workability without increased water content I Reduces shrinkage and thus avoid crack formation I Leads to better finish.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE1 kg / 50 kg of cement.DIRECTIONS OF USEDry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 70-80% of required water and mix for 2-3 minutes I In the remaining portion of water add Water Seal Powder. Then add this to concrete mixer and mix for another 2-3 minutes for a homogenous mix I Place the concrete or apply plaster as per your need I Cure as per the normal procedure.NOTEDo not add Water Seal directly to dry cement or aggregate mix I Do not increase the dosage of Water Seal beyond the recommended level I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

Water Seal is an integral powder waterproofing admixture for all types of concrete,

plaster and mortar.

PACKAGING

WATERSEAL

POWDER WATER PROOFING COMPOUND

100 ml 500 ml 1 Lt 2.5 Lt 5 Lt 20 Lt

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Wine red/dark brown Specific gravity @ 27°C 1.05 – 1.07 Non-volatile content 10 – 12 % pH 9 – 13Setting time 30 – 600 minutesUSESBasements I Roof slaps and screeds I External plastering I Balconies and bathrooms I Water tanks, water retaining structures and terrace I Sumps and drains I Beams and columns I Repair and renovation works.BENEFITSCompatible with all types of cements I Reduces the permeability of water into concrete and improves water tightness I No added chloride thus not contributing to corrosion of steel I Reduces capillary structures formed in concrete I Facilitates better workability without increased water content I Reduces shrinkage and thus avoid crack formation I Leads to better finish.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE100 ml / 50 kg of cement.DIRECTIONS OF USEDry mix the sand, aggregates and cement as per the mix design in a concrete mixer for 2 minutes I Then add 70-80% of required water and mix for 2-3 minutes I In the remaining portion of water add Wet Seal. Then add this to concrete mixer and mix for another 2-3 minutes for a homogenous mix I Place the concrete or apply plaster as per your need I Cure as per the normal procedure.NOTEDo not add Wet Seal directly to dry cement or aggregate mix I Do not increase the dosage of Water Seal beyond the recommended level I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

Wet Seal is an integral liquid waterproofing admixture for all types of concrete,

plaster and mortar.

PACKAGING

CEMENT WATER PROOFING COMPOUND

WETSEAL

OYT is a water-based emulsion composedof acrylic polymers and selected ingredients which is specially designed for water tanks.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth paste Colour Cow dung colour Specific gravity @ 27°C 1.40 ± 0.05 Non-volatile content 55.00 ± 5.00%Viscosity 3000 – 5000 cPpH 8.00 ± 1.00Finish Rich mattSurface dry 30 minutesOver coating interval 4 – 6 hoursStabilityof thinned paint 24 hoursUSESWater tanks, septic tanks I Swimming pools.BENEFITSAlternate to chlorinated rubber paint I Environment friendly I Advanced formulation to arrest water leakage I Elastomeric flexible coating I Excellent resistance to ingress of water I Non toxicI Safe for potable water.

SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE400 ml of water per litre of OYT.COVERAGE100 – 110 sq.ft / litre / coat. DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Apply one coat of Veco Primer and allow it to dry for 4-6 hours I Dilute with 40% of water by volume to OYT and stir thoroughly to get homogenous mixture I Apply single coat and allow it to dry for about 4-6 hours I After 4-6 hours, apply another coat.NOTEDo not apply on wet tanks I Ambient and surface temperatures must be between 5°C and 40°C during application.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

TANK COATEMULSION

OYT

1 Lt 4 Lt 10 Lt 20 Lt

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Two-componentAppearance of mix Free-flowing slurrySpecific gravity @ 27°C 1.60±0.10Viscosity of mix 10000 ± 2000 cPpH 10.00 – 12.00Pot life of mix 40 – 45 minutesSurface dry 30 minutesWater Excellent – no leakagepermeability after 24 hours Over coatinginterval 4 – 6 hoursUSESConcrete walls, roofs, terrace I Concrete roof slabs, floors, balcony floor slabs I Water tanks and swimming pools I Waterproof coating (bottom coat) for marble, granite and other natural stones.BENEFITSFlexible and permeable coating I Waterproofing for concrete structures I Excellent adhesion to concrete and natural stones I Can be applied as thick coating.RECOMMENDED MIX RATIO4:1 (Part A: Part B) (Part A = Powder & Part B = Liquid).

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.COVERAGE70 – 80 sq.ft/litre/coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, oil, wax, rust and loose or peeling paint before painting I Repair holes and cracks with a thick paste of V-Flex G2K prepared in the recommended ratio I Prepare the main batch of V-Flex G2K in the recommended ratio and stir thoroughly to get a homogenous mixture I Wet the surface with water by sprinkler and apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, repeat the above process.NOTEThe entire quantity of both the components have to be mixed and used at one go I For best results do not dilution with water.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

V-Flex G2K is a two-component cementitious polymer modified elastomeric, waterproofing & protective coating. which reduces the room

temperature up to 7 – 9°C at peak summer hours.

PACKAGING

ACRYLIC CEMENTITIOUS WATER-PROOFING COATING

V - FLEX G2K

1 Kg 5 Kg 10 Kg 20 Kg

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour Clear/White Specific gravity @ 27°C 1.00 ± 0.10Non-volatile content 15.00 / 45.00pH NeutralDrying time 15 – 30 minutesUSESBuilding structures, cement plaster structures I Precast concrete, concrete blocks, concrete rendering I Asbestos sheets I Natural stones and artificial stones I Ceramic tiles, clay brick surfaces I Mangalore tiled roofs, corrugated AC roofings I Painted surfaces.BENEFITSReady to use primer I Available in both water-based and solvent-based formulations I Clear coating does not change the appearance of surface I Penetrates up to 3-4 mm I Prevents erosion I Prevents efflorescence.

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE40 – 80 sq. ft / litre / coat depending upon the porosity of the surface.DIRECTIONS OF USESurface should be cleaned thoroughly I Stir the containers well before use. Apply V-Repel evenly over the surface with brush/spray I On vertical applications, starting from the bottom, apply V-Repel in an upward direction achieving 6-8 inches rundown I After applying 2 coats for best results, allow 48-72 hours for complete penetration.NOTEDo not dilute V-Repel with any solvent/water I Close the lid after use.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.V-Repel is a silane/siloxane based penetrating

sealer for effective water repellent protective coating.

PACKAGING

WATER REPELLENT PRIMER

V - REPEL

250 ml 500 ml 1 Lt 2.5 Lt 5 Lt 20 Lt

CEMENT WATERPROOFING COMPOUND

V-Seal is a waterproofing compoundfor all types of concrete, plaster and mortar.

PACKAGING1 Lt 5 Lt 20 Lt

V - SEALPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free flowing liquidColour AmberSpecific gravity @ 27°C 1.10 – 1.20Non-volatilecontent 20 – 30%ph 7 - 8USESBasements I Roof slaps and screeds I External plastering I Balconies and bathrooms I Water tanks, water retaining structures and terraces I Sumps and drains I Beams and columns I Repair and renovation work.BENEFITSCompatible with all types of cements I Reduces the permeability of water into concrete and improves water tightness I No added chloride thus not contributing to corrosion of steel I Reduces capillary structures formed in concrete I Facilitates better workability without increased water content I Reduces shrinkage and thus avoids crack formation I Leads to better finish.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packing

and if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DILUTION100 – 200 ml / 50 kg of cement.DIRECTIONS OF USEIn a concrete mixer, dry mix the sand, aggregates and cement as per the mix design for 2 minutes I Then add 70-80% of water and mix for 2-3 minutes I In the remaining portion of water add V-Seal. Add this to the concrete mixer and mix for another 2-3 minutes for a homogenous mix I Place the concrete or apply plaster as per your need I Cure as per the normal procedure.NOTEDo not add V-Seal directly to dry cement or aggregate mix I Do not increase the dosage of V-Seal beyond the recommended level I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

Vijay Ultima is a water-based emulsion composed of acrylic polymers and special ingredients.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth paste Colour As per customer equirementSpecific gravity @ 27°C 1.10±0.05 Non-volatile content 45.00±5.00%Viscosity 15000 ± 2000 cPpH 8.00 ± 1.00Finish Rich mattSurface dry 30 minutesOver coating interval 4 – 6 hoursStability of thinned paint 24 hoursUSESDecorative coating for exterior walls & plastered surfaces I Exterior coating for dry wall surfaces like gypsum, cement fibre boards, asbestos sheets etc.BENEFITSRich matt finish I Good hiding property I Allows the surface to breathe and expel moisture I Waterproofing I Very good intercoat adhesion I Can be applied by brush or rollers I Free from heavy metals like mercury, lead and chromium.

SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DOSAGE400 ml of water per litre of cement primer.COVERAGE120 – 140 sq.ft/litre/coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Application should start 4 hours after the application of Primer I Dilute with 40% of water by volume to Vijay Ultima and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 4-6 hours I After 2-4 hours, apply another coat.NOTEThe moisture content of the wall must be less than 10% or have aged for at least 28 days I Ambient and surface temperatures must be between 5°C and 40°C during application.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

1 Lt 4 Lt 10 Lt 20 Lt

VIJAYULTIMASMOOTH FINISH

EXTERIOR EMULSION

1 Lt 4 Lt 10 Lt 20 Lt

Veco Interior Emulsion is a water based emulsion composed of acrylic polymers

and special ingredients.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth paste Viscosity 45000 ± 5000 cP Specific gravity @ 27°C 1.50±0.05 Non-volatile content 60±5% pH 10.00±1.00Finish Rich mattSurface dry 30 minutesColour Base / WhiteOver coating interval 4 – 6 hoursStability of thinned paint 24 hours USESDecorative coating for interior walls & plastered surfaces I Decorative coating for dry wall surfaces like gypsum, cement fibre boards, etc.BENEFITSRich matt finish I Good hiding property I Allows the surface to breathe and expel moisture I Waterproofing I Very good intercoat adhesion I Can be applied by brush or rollers I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DILUTION400 ml of water per litre of cement primer.COVERAGE120 – 140 sq.ft/litre/coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Application should start after 4 hours from the application of Veco Cement Primer I Dilute with 40% of water by volume to Veco Interior Emulsion and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

INTERIOR EMULSION

Reve Bond is a clear cem adhesive to be used with lime wash

or powdered distemper.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Lumps free liquid Colour ClearSpecific gravity @ 27°C 1.00 – 1.10 Non-volatile content 4 – 7% pH NeutralBENEFITSEffective bonding I Enhances the life of the cem coating I Covers the cracks in the surface I Improves the glossy of the cem coating I Increase the coverage of the cem coating.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

ADVANTAGESEnhances durability I Chalky/dusty surface minimised I Cracking/peeling reduced I Enhances glossy appearance of the walls.RECOMMENDED DOSAGE250g adhesive for 10 kg lime wash.DIRECTIONS OF USESurface must be clean, dry and free of dirt, chalk, grease, wax, rust, etc I Mix the recommended quantity of Reve Bond with lime wash or distemper powder I Paint the mixed lime wash or distemper with brush I Apply 2 coats.NOTEDo not add water to Reve Bond directly.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

CEM ADHESIVE

125 gm 250 gm 500 gm 1 kg

Total Bond is a white colour cem adhesiveto be used with lime wash

or powdered distemper.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Lumps free liquid Colour WhiteSpecific gravity @ 27°C 1.00 – 1.10 Non-volatile content 4 – 7% pH NeutralBENEFITSEffective bonding I Enhances the life of the cem coating I Covers the cracks in the surface I Improves the glossy of the cem coating I Increase the coverage of the cem coating.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

ADVANTAGESEnhances durability I Chalky/dusty surface minimised I Cracking/peeling reduced I Enhances glossy appearance of the walls.RECOMMENDED DOSAGE250g adhesive for 10 kg lime wash.DIRECTIONS OF USESurface must be clean, dry and free of dirt, chalk, grease, wax, rust, etc I Mix the recommended quantity of Total Bond with lime wash or distemper powder I Paint the mixed lime wash or distemper with brush I Apply 2 coats.NOTEDo not add water to Total Bond directly.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

PREMIUM CEM ADHESIVE

125 gm 250 gm 500 gm 1 kg

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature Smooth pasteViscosity 25000 ± 5000 cPSpecific gravity @ 27°C 1.50±0.05Non-volatile content 60±5% pH 8.00 – 10.00Finish Rich mattSurface dry 30 minutesColour Base / WhiteOver coating interval 4 – 6 hoursStability of thinned paint 24 hours USESDecorative coating for interior walls & plastered surfaces I Decorative coating for dry wall surfaces like gypsum,cement fibre boards, etc.BENEFITSRich matt finish I Good hiding property I Allows the surface to breathe and expel moisture I Waterproofing I Can be applied by brush or rollers I Available in both Baseand White variants I Base can be tintedwith different colours.

SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protectfrom direct sunlight.RECOMMENDED DILUTION600 ml of water per kg of distemper.COVERAGE80 – 90 sq.ft / litre / coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Application should start after 4 hours from the application of Veco Cement Primer I Dilute with 40% of water by volume to Veco Distemper and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours I After 2-4 hours, apply another coat.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

Veco Distemper is a water-based emulsion composed of acrylic polymers

and special ingredients.

PACKAGING

VECO DISTEMPERACRYLIC EMULSIONBASED DISTEMPER

1 Lt 4 Lt 10 Lt 20 Lt1 Lt 4 Lt 10 Lt 20 Lt

Veco Cement Primer is a water-based acrylic primer suitable for interior & exterior sand

plastered surfaces, concrete and asbestos, etc.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSNature White, smooth paste Viscosity 10000 ± 2000 cP Specific gravity @ 27°C 1.50±0.05 Non-volatile content 50 – 60% pH 10.00 ± 1.00Sheen level Soft sheenSurface dry 30 minutesOver coating interval 4 – 6 hoursStability of thinned paint 24 hours USESCement plasters, concrete, cementitious renderings I Asbestos, brick works, gypsum boards I False ceilings.BENEFITSSmooth finish I Good hiding power I Allows the surface to breathe and expel moisture I Seals porous surfaces I Very good intercoat adhesion I Seals chalky surfaces, improves top coat adhesion I Free from heavy metals like mercury, lead and chromium.SHELF LIFE & STORAGEBest before 12 months in an unopened,

undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.RECOMMENDED DILUTION750 ml of water per litre of cement primer.COVERAGE110 – 120 sq.ft/litre/coat.DIRECTIONS OF USEAll surfaces must be clean, dry and free of dirt, chalk, grease, wax, rust and loose or peeling paint before painting I Repair holes and cracks with suitable filler I Dilute with 75% of water by volume to Veco Cement Primer and stir thoroughly to get a homogenous mixture I Apply single coat and allow it to dry for about 2-4 hours.NOTEAmbient and surface temperatures must be between 5°C and 40°C during application I The moisture content of the wall must be less than 10% or have aged for at least 28 days.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

CEM PRIMERWATER THINNABLE

Reve Grip is a special universal gum to be used with cem or white cement

or powdered distemper.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Homogeneous liquidColour WhiteSpecific gravity @ 27°C 1.00 – 1.10Non-volatilecontent 4 – 7%ph range NeutralBENEFITSEffective bonding I Enhances the life of the cem coating I Covers the cracks in the surface I Provides emulsion finish I Increase the coverage of the cem coating.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGE50-100 ml Reve Grip for 5 kg of white cement.DIRECTIONS OF USESurface must be clean, dry and free of dirt, chalk, grease, wax, rust, etc I Mix the recommended quantity of Reve Grip with white cement or cem I Paint the mixed white cement or cem or distemper with brush. NOTEDo not add water to Reve Grip directly.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

500ml 100ml 250ml 500ml

REVE GRIPSPECIAL

UNIVERSAL GUM

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance White, smooth pasteTrack free time 30 minutesSpecific gravity @ 27°C 1.40±0.05 Maximum jointmovement ±10%Full cure 2 – 3 daysVertical sag No saggingShore A Hardness* 80±5Tensile strength* 15 ± 2 N/cm*Typical properties after seven days cure at normal atmospheric condtionsUSESExpansion joints in precast concrete boards, cement boards I Joints in block-work, brickwork and timber/steel joints I Cracks in concrete, plasterboards, cement boards & brickworks I Sealing around ceramic tiles I Sealing window and door frames I Sealing between light partition walls.BENEFITSExcellent sealing and adhesion properties I Over paintable I Outstanding flexibility I Waterproofing I Paste form, no sagging and easy to apply I Excellent resistance to UV and atmospheric conditions.SHELF LIFE & STORAGEBest before 6 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

JOINT CONFIGURATIONMinimum joint width = 1 mmMaximum joint width = 5 mmCOVERAGE6 – 7 running meter/kg (for 3 mm width and 5mm depth).DIRECTIONS OF USEBefore starting the applications, ensure all surfaces are clean, dry and free from dust and grease I Remove all loose materials from the surface with air blower or brush I Apply primer coat over the joint & the surfaces where Elasto Joint- 504 has to be applied I Fill & press Elasto Joint- 504 paste tightly into the joint with a spatula or putty knife and level with surface without any formation of cavities or bubbles I Apply Elasto Joint - 504 for 1.5 inches on both sides of the joint like a putty application I Allow it to set for 24-hours prior to another coat or other applications I For best results allow Elasto Joint - 504 to cure for 7 days.NOTEDon’t use underwater I Don’t use to seal submerged joints I Don’t apply on damp substrates I Do not use in external applications where rain is imminent within 4 hours I Allow to dry for 24-hours I For application below 10°C, drying time will be delayed I Container should be closed tight after application.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

Elasto Joint – 504 is a single pack, water-based ready to use flexible sealant for interior

and exterior cracks up to 5mm width.

PACKAGING1 Kg 5 Kg 10 Kg 20 Kg

ELASTO JOINT 504

FLEXIBLE CRACK FILLING PASTE

1 Kg 5 Kg 20 Kg

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquid Colour Milky whiteSpecific gravity @ 27°C 1.00 – 1.05Non-volatile content 30.00±3.00% pH range 8 – 10USESWalls, roofing, terraces I Bathrooms, kitchens, balconies I Concrete repair work I Water retaining structures I Basements I Sealing hairline cracks I Mortar block work and brickwork.BENEFITSReduces the permeability of water into concrete and improves water tightness I Anti-efflorescence I Completely arrests water leakages I Good adhesion I Easy mixing and application I Flexible. SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGEDamp proofing 1 part V-Crete : 4 part Water : 10 part CementSalty 1 part V-Crete : 4 part petre resisting Water : 10 part Cement (this mixture has to be applied by brush after the application of V-Repel and before plastering)Crack filling 1 part V-Crete : 2 parts cement (white / grey)Wear and impact Add 5 to 10% resisting by weight of cementDIRECTIONS OF USEThe surfaces must be be clean and free from oil, grease, dust, rust, etc I Prepare V-Crete solution by mixing it with water. Add this mixture to the required cement and sand combination to prepare cement mortar, plastering, waterproofing / bond coat, putty I Dampen the surface and apply the V-Crete modified cementitious mixture by brush or trowel I Cure by spraying water periodically for 2 – 3 days.NOTEDo not add V-Crete directly to dry cement or aggregate mix I Use the mixture within 30-minutes from the time of preparation I Maintain water-cement ratio as low as possible.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of waterI Keep out of reach of children.

V-Crete is an acrylic polymer-based white liquid. When this liquid is mixed with cement,

that composite becomes sticky, strong and helps resist dampness.

PACKAGING

CEMENT DAMP PROOF

V - CRETEPRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSAppearance Free-flowing liquidColour Milky WhiteSpecific gravity @ 27°C 1.00 ± 0.10Non-volatile content 35.00 ± 3.00% pH range 7 – 9USESFor concrete repair, particularly those concrete structures which are damaged due to Corrosion of reinforcement I Bridge deck overlays and cement patching work I Waterproofing treatment I For bonding old to new concrete I As an admixture for making polymer modified mortar & concrete I For fixing tiles I Abrasion resistant and anti-corrosive floor.BENEFITSWaterproofing I Corrosion inhibition I Protects surface from attack of salty petre I Universal repair product.SHELF LIFE & STORAGEBest before 12 months in an unopened, undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

RECOMMENDED DOSAGEWaterproofing 1 part V-Crete URP : 4 or bonding coat part water : 6 part CementRepair, 1 part V-Crete URP: 4 part plastering and Water : Cement & Sand sealing mortar as requiredAbrasion resistant Add 5 to 10% by weight flooring of cementIntegral 200 ml for 50 kgWaterproofing cement bagDIRECTIONS OF USEThe surfaces must be be clean and free from oil, grease, dust, rust, etc I Prepare V-Crete URP solution by mixing it with water. Add this mixture to the required cement and sand combination to prepare cement mortar, plastering, waterproofing / bond coat, putty I Dampen the surface and apply the V-Crete URP modified cementitious mixture by brush or trowel I Cure by spraying water periodically for 2– 3 days.NOTEPrepared material must be used within 30 minutes I Never add V-Crete URP directly to cement.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin, wash with plenty of water I Keep out of reach of children.

V-Crete URP is a rubberised polymer, specifically designed for use with cement formulations,

in making cement modified coatings, polymer modified mortars and concrete.

PACKAGING

STYRENE BUTADINE RUBBER LATEX COMPOUND

V - CRETE

URP

250 ml 500 ml 1 Lt 3 Lt 5 Lt

Paint-X is a solvent-based, non flammable, instant paint remover which conforms to IS 430.

PACKAGING

PRODUCT CHARACTERISTICSPROPERTIES SPECIFICATIONSType Solvent based Colour Off whiteToxicity Non toxicNon-volatile content 3 – 5% pH Neutral USESSuitable for household, industrial, automotive and marine applications I Wood and metal surfaces.BENEFITSStarts to remove paint in 5 minutes I Non flammable I Non alkaline and non corrosive I Deep penetration, hence removes multiple layers in a single shot I Can be used in vertical surfaces also I Less evaporation rate I Available in both tin and spray type containers.SHELF LIFE & STORAGEBest before 12 months in an unopened,undamaged, originally sealed packingand if stored in dry conditions I Protect from direct sunlight.

COVERAGE20 sq.m/ litre (variable to paint thickness).DIRECTIONS OF USEShake well before use and apply liberally over the paint surface by brush or by spraying I Use general precautionary measures as done during regular painting I Wait for 5 minutes or until top layer peels and scrub the paint with a putty knife I For stubborn paint residues, apply Paint-X over them once more and remove in about 2 to 3 minutes I If the paint film is too thick, Paint-X may take additional time to penetrate and the surface may need another coat.NOTEDon’t use on plastic/polymeric surfaces I Don’t dilute the material with any solvent.HEALTH & SAFETY PRECAUTIONSUse rubber hand gloves & safety goggles I In case of contact with skin,wash with plenty of water I Keep out of reach of children.

PAINT REMOVER

PAINT X

250 ml 500ml 1 Lt 3 Lt

Tin type:

330 gm 550gm

Spray type: