listing constructional data report (cdr)lhs.pdf · listing constructional data report (cdr) report...

Listing Constructional Data Report (CDR)

Report Number 141015030GZU-001 Original Issued: 8-Jan-2015 Revised: None

Standard(s)

Applicant Manufacturer

Address Address

Country CountryContact ContactPhone PhoneFAX FAXEmail [email protected] [email protected]

0750-30903820750-3090382

Motor-Operated Household Food Preparing Machines-UL 982, 6th Edition, Rev. Jun. 9, 2010Portable Electrical Motor-Operated and Heating Appliances: Particular Requirements forElectrical Motor-Operated Kitchen Appliances-CSA C22.2 No.1335.2.14-93 R2013, See also CSA C22.2 No.1335.1-93 R2013

York liang York liang

1.0 Reference and Address

No. 11, Tongle Rd., Tangxia town,Pengjiang Qu, Jiangmen, Guangdong,China

0750-3097695 0750-3097695

No. 11, Tongle Rd., Tangxia town,Pengjiang Qu, Jiangmen, Guangdong,China

China

Sinsion Technology Industrial Co., Ltd

China

Sinsion Technology Industrial Co.,Ltd

of 33

Report No. 141015030GZU-001Sinsion Technology Industrial Co., Ltd

of 33 Issued: 8-Jan-2015Revised: None

ProductBrand name

Models

Model Similarity

RatingsOther Ratings NA

120 V, 60 Hz, 240 W.

2.0 Product Description

ROCKET BLENDERSENSIO, COOKS

DescriptionThe product covered by this report are ROCKET BLENDERs having a rating of 120 V, 60 Hz,for household and indoors use only, provided with a non-detachable power supply cordterminated in a 2-wire polarized type plug.

HB-1102, HB-1102A, HB-1103

HB-1102 is identical with HB-1102A, except the side enclosure of HB-1102 is metal.HB-1103 is identical with HB-1102A, except the shape of enclosure.

ED 16.3.15 (1-Jan-13) Mandatory



Photo 1 - External View of HB-1102 and Accessories

3.0 Product Photographs

17

1

Blender Cup

Coffee mill Cup

Photo 2 - External View of HB-1102

16





Photo 3 - External View of HB-1102

15

Photo 4 - Bottom View of HB-1102 and HB-1102A

2

5





Photo 5 - Internative View of HB-1102 and HB-1102A

3

4

Photo 6 - Internative View of HB-1102

1312

14






6

7

8

9


10

11





Photo 9 - External View of HB-1102A

Photo 10 - External view of HB-1103





Photo 11 - Bottom view of HB-1103

Photo 12 - Internal View of HB-1103Photo 12 Internal View of HB 1103





Photo 13 - Extenal view of alternative outside ( with plated Lower Enclosure)




Ph

oto

#

Item

no.1Name

Manufacturer/

trademark2 Type / model2Technical data and securementmeans

Mark(s) ofconformity

3

1 1 Power Cord Set Various SPT-2

Rated 300 V, 105 ºC, VW-1, 18AWG x 2C. Not less than 0.61 mfrom cord entry to plug face,flexible cord integrally molded ona recognized 2-wire polarized type1-15P plug.

cURus

4 2 Cord BushingKINGFA SCI &TECH CO LTD

VSLOY-PM Rated V-0, HWI=1, HAI=0, 95 ,minimum 1.5 mm thick.

cURus

5 3 Cord Clamp

A SCHULMANPLASTICS(DONGGUAN)LTD

XP 31 RPC material. Rated HB, 80 ,minimum 1.5 mm thick.

cURus

5 4 Bottom Cover

HUIZHOU WOTEADVANCEDMATERIALS COLTD

2100-FR615

ABS material. Rated V-0, HWI=3,HAI=1, CTI=1, 60 , minimum1.6 mm thick. Overall measured Ф114 mm x 65 mm for HB-1102,HB-1102A, measured Ф113 mm x71 mm for HB-1103.

cURus

4 5 Foot Various VariousRubber material. Rated HBminimum, measured 10 mm indiameter and 2 mm extended.

cURus

7 6 Internal Wire Various 1015Rated 600 V, VW-1, 105 ,minimum 22 AWG, servised asmotor leading wire.

cURus

GUANGZHOUTAIHENGELECTRONIC &ELECTRICAL COLTD

THW-3Two provided. Rated 125 V, 5 A,125 . 6000 cycles endurance.

cURus

GUANGZHOUQUANTAIELECTRIC COLTD

SMA-2Two provided. Rated 125 V, 6 A,85 . 6000 cycles endurance.

cURus

YUEQINGDONGNANELECTRONICSCO LTD

KW4ATwo provided. Rated 125 V, 5 A,85 . 6000 cycles endurance.

cURus

7 8 Interlock Shaft

ASAHI-DUPONTPOM(ZHANGJIAGANG) CO LTD

3510POM material. Rated HB, 90 ,minimum 0.9 mm thick.

cURus

8 9 Spring Various VariousSteel Wire measured Ф0.5 mm.Measured 15 mm long.

cURus

8 10 MotorSinsionTechnologyIndustrial Co., Ltd.

SX54/30Rated 120 V, 60 Hz, tested withappliance.

See 5.0

8 11 Motor Bracket RTP CORTP PA66 30GF FR0 BLK

PA6/6 material. Rated V-0, 105, minimum 0.8 mm thick.Overall measured Ф89.5 mm x46.5 mm.

cURus

6 12 Lower Enclosure


2100-FR615

For HB-1102, HB-1102A only.ABS material. Rated V-0, HWI=3,HAI=1, CTI=1, 60 , minimum1.6 mm thick. Overall measured Ф117.8 mm x 46.5 mm. May beplated outside.

cURus

4.0 Critical Components

Interlock Switch77




Ph

oto

#

Item

no.1Name

Manufacturer/

trademark2 Type / model2Technical data and securementmeans

Mark(s) ofconformity

3

4.0 Critical Components


2100-FR615

For HB-1102 only. ABS material.Rated V-0, HWI=3, HAI=1, CTI=1,60 , minimum 1.6 mm thick.Overall measured Ф110 mm x Ф98.5 mm x 121.5 mm.

cURus

Various Various

For HB-1103, HB-1102A only.SUS201 material. Minimum 0.4mm thick, overall measured Φ110mm x Φ98.5 mm x 121.5 mm forHB-1102 A, Φ113 mm x Φ99 mmx 199 mm for HB-1103.

NR

6 14 Upper Enclosure


2100-FR615

ABS material. Rated V-0, HWI=3,HAI=1, CTI=1, 60 , minimum1.6 mm thick. Overall measured Ф103 mm x 61.5 mm.

cURus

3 15 Driving Coupler RTP CORTP PA66 30GF FR0 BLK

PA6/6 material. Rated V-0, 105, minimum 0.8 mm thick.

cURus

2 16 Cup

NINGBO LGYONGXINGCHEMICAL COLTD

80HF

SAN material. Rated HB, 50 ,minimum 1.5 mm thick. Overallmeasured Ф86.5 mm x Ф68.5mm x 157.5 mm long for blender,measured Φ86.5 mm x Φ68.5 mmx 102 mm long for coffee mill.Both cups are marked max. lineon the side.

cURus

1 17 Cutter Base Various Various Consisted of following parts. cURus

1 17a Coupler MatchDongguan AMGElectronics Ltd

GTP-(X)Silicone Rubber, rated V-0, 105, minimum 0.5 mm thick.

cURus

1 17b Plastic Base RTP CORTP 20(o) FRXC

Rated V-0, 105 , minimum 0.75mm thick. Measured Ф84.5 mm x38.5 mm.

cURus

1 17c Shaft Various VariousSUS303 material. Measured Ф6.0mm x 31.5 mm long.

NR

1 17d Blade Various VariousSUS301 material. Measured 1.0mm thick.

NR

1 17e Shaft Seal Ring3M CHINA COLTD

5516-ST Silicone. Rated V-0, 105 ,minimum 0.5 mm thick.

cURus

1 17f Cup Seal RingDongguan AMGElectronics Ltd

GTP-(X)Silicone Rubber, rated V-0, 105, minimum 0.5 mm thick.

cURus

4 18Marking Label(Not Shown)

Various VariousFor ABS and stainless steelsurface. Rated min. 70 .

cURus

13 Side Enclosure

3) Indicates specific marks to be verified, which assures the agreed level of surveillance for the component. "NR" - indicates Unlisted andonly visual examination is necessary. "See 5.0" indicates Unlisted components or assemblies to be evaluated periodically refer to section5.0 for details.

1) Not all item numbers are indicated (called out) in the photos, as their location is obvious.

2) “Various“ means any type, from any manufacturer that complies with the "Technical data and securement means" and meets the "Mark(s)of conformity" can be used.

NOTES:

6




Photo # Item no.

8 10

A

Motor

INSULATED COIL

Rated 250VAC, 5 A, Tf=130. Others same asabove.

P2-3A-F

Rated 250VAC, 3A, Tf=115. Enclosed byimpregnated fiberglass tubing, and wrap byinsulating tape,then tightly secured to thestator winding by metal clamp.

AUPOELECTRONICSLTD

120 V, 60 Hz, 240 W. Insulation class

5.0 Critical Unlisted CEC Components

Name Manufacturer/Trademark

VariousPA material, rated at least 105 °C, used forbinding the lead wires and thermal protector.

HB-77Vulcanized fibre Industrial laminates. Rated HB,110 ºC, minimum 0.71 mm thick.

Type / model

MATERIALS LIST (refer to illustration 4 for assembly drawing)Component Manufacturer Type/model Dimensions/thickness/assembly information

Sinsion TechnologyIndustrial Co., Ltd.

SX54/30

Component Standard used: Tested with appliance.Electrical Rating:

Stator Magnet Wire

Consisted of Si steel sheets.Each sheet 0.5 mmthick.

Rotor Lamination Various VariousConsisted of Si steel sheets. Each sheet 0.5mm thick.

Stator Lamination Various Various

Rotor Magnet Wire

DONG GUANYIDAINDUSTRIAL COLTD

1PEWANSI Type MW 5-C, Temperature Class: 155.Ф0.25 mm, total 60 coils.

410Aramid Insulating Paper, rated V-0, HWI=0,HAI=0, CTI=3, 220°C, min. 0.254mm thick.

ANSI Type MW 79-C, Temperature Class: 155.Ф0.43 mm, total 170 coils.

Various Various

Copper material. Overall 15 mm OD by 10mm long. Consists of 10 segments, each 4.0mm wide, insulated from motor shaft byphenolic composition ring.

1022/(#)PA material, Rated HB, HWI=0, HAI=0,CTI=1, 105 °C. Minimum 1.5 mm thick.

DONGGUANSHENGJIAENAMELLEDWIRE CO LTD

2UEW

PANASONICCORPORATION

CN4610Phenolic, rated V-0, HWI=0, HAI=0, CTI=2, 150°C. Minimum 0.75 mm thickness.

Various

Slots Liner for Statorand Rotor

E I DUPONT DENEMOURS & COINC

HOKUETSUTOYO FIBRE COLTD

Cable Tie

Solvay SpecialtyPolymers USA L LC

Thermal Protector

Insulated Tubing Various Various

AUPOELECTRONICSLTD

P4-5A-F

Impregnated fiberglass sleeving.

Cable Tie Various Various Rated 105minimum, VW-1.Insulating Tape Various Various Rated min.130.

Fan Blade Various VariousPA66 material. Rated HB minimum, 105 °Cminimum, Min. 0.8 mm thick, with 10 blades,tightly secured to the shaft of the motor.

Commutator

Spider of Rotor

Wedge

Commutator Holder




5.0 Critical Unlisted CEC Components

170 / /60 / /

Frequency: Annual 1

Brush Holder

SHANGHAIEUROPEANASIAN SYNTHETICMATERIAL COLTD

EA-7501JTwo provided, Melamine / Phenolic Compound,rated V-0, HWI=0, HAI=0, CTI=0, 150°C.Minimum 0.8mm thickness.

WINDING(S) RESISTANCEWindingDesignation

Wire Size

(AWG or mm2)Wire Type Turns Volts Amps

DC resistance(Ω) +/- 10%:

Test Name Test Parameters

Stator Magnet Wire Ф0.43 mm Cu wire 2.6Rotor Magnet Wire Ф0.25 mm Cu wire 7.0

Dielectric StrengthApply voltage Between Test Voltage Test Time

Primary to core 1000 60

Winding resistance See resistance per winding above.

VERIFICATION PROCESSTest Site: CEC Number of samples to test:




2. Mechanical Assembly - Components such as switches, fuseholders, connectors, wiring terminals and displaylamps are mounted and prevented from shifting or rotating by the use of lockwashers, starwashers, or othermounting format that prevents turning of the component.

3. Corrosion Protection - All ferrous metal parts are protected against corrosion by painting, plating or theequivalent.

4. Accessibility of Live Parts - All uninsulated live parts in primary circuitry are housed within a metal or non-metallic enclosure constructed with no openings other than those specifically described in Sections 4 and 5.

5. Polarized Connection - This product is provided with a polarized power supply connection. All single poleswitches and fuses are connected only to the ungrounded supply circuit conductor.

6. Internal Wiring - Internal wiring is routed away from sharp or moving parts. Internal wiring leads terminatingin soldered connections are made mechanically secure prior to soldering. Recognized Componentseparable (quick disconnect) connectors of the positive detent type, closed loop connectors, or other typesspecifically described in the text of this report are also acceptable as internal wiring terminals. At pointswhere internal wiring passes through metal walls or partitions, the wiring insulation is protected againstabrasion or damage by plastic bushings or grommets.

7. Marking - The product is marked on a component labeling system as follows:- manufacturer’s name, trade name- model number- date of manufacture- electrical ratings (volts, power & frequency)- refer to Marking 1 for details.

8. Installation, Operating and Safety Instructions - Instructions for installation and use of this product areprovided by the manufacturer. Upper case and lower case letters shall not be less than 2.0 mm and 1.6 mmin height respectively. The phrases “IMPORTANT SAFEGUARDS” and “SAVE THESE INSTRUCTIONS”shall be in letters not less than 4.8 mm in height. (Refer to Illustration 2 for details.)

9. Carton Markings - The following are required: -The “HOUSEHOLD USE ONLY” or “HOUSEHOLD TYPE” must be located on at least one outsidesurface. -Appear in lettering not less than the height as specified: The dimension of the carton panel (mm) Minimum height of lettering (mm) 0~152 3.2 152~254 4.8 more than 254 6.4

Critical Features/Components - An essential part, material, subassembly, system, software, or accessory of aproduct that has a direct bearing on the product’s conformance to applicable requirements of the productstandard.Construction Details - For specific construction details, reference should be made to the photographs anddescriptions. All dimensions are approximate unless specified as exact or within a tolerance. In addition to thespecific construction details described in this Report, the following general requirements also apply.

Recognized Component - A component part, which has been previously evaluated by an accredited certificationbody with restrictions and must be evaluated as part of the basic product considering the restrictions as specifiedby the Conditions of Acceptability.

6.0 Critical Features

Unlisted Component - A part that has not been previously evaluated to the appropriate designated componentstandard. It may also be a Listed or Recognized component that is being used outside of its evaluated Listing orcomponent recognition.

1. Spacing - In primary circuits, 1.6 mm minimum spacing are maintained through air and over surfaces ofinsulating material between current-carrying parts of opposite polarity and 1.6 mm minimum between suchcurrent-carrying parts and dead-metal parts or low voltage isolated circuits.

Listed Component - A component part, which has been previously Listed or Certified by an accreditedCertification Organization with no restrictions and is used in the intended application within its ratings.




Illustration 1 - Marking

7.0 Illustrations

Note:

1) “CAUTION: DO NOT IMMERSE IN WATER”, “FOR HOUSEHOLD USE ONLY”, “READ ALL INSTRUCTIONS BEFORE USING” and their equivalent French shall be not less than 2.4 mm high in letters.2) “NEVER PLACE BLADE ASSEMBLY ON BASE UNLESS ASSEMBLED TO JAR” and its equivalent French shall be not less than 2.4 mm high in letters.3) The ETL logo shall not be less than 8 mm in width and 8 mm in height, and the “C” and “US” shall not be less than 2 mm in height. "Intertek" shall not be less than 3 mm in height. "CONFORMS TO UL STD. 982", "CERTIFIED TO CSA STD. C22.2 No. 1335.1 & 1335.2.14" and the control no. "4008084" and the letter height shall not be less than 2 mm in height.4) Date Code “YYWW”, "YY" means year , "WW" means week. 5) For "ITEM#" on the marking label, "X" may be 0-9.




7.0 Illustrations

Illustration 1a - Marking

Note:





7.0 Illustrations

Illustration 1b - Marking

Note:





7.0 Illustrations

Illustration 2 - Instruction Manual




7.0 Illustrations

Illustration 2a - Instruction Manual




7.0 Illustrations

Illustration 2b - Instruction Manual




7.0 Illustrations

Illustration 2c - Instruction Manual




7.0 Illustrations

Illustration 2d - Instruction Manual




7.0 Illustrations

Illustration 3 - Circuit Diagram




7.0 Illustrations

Illustration 4 - Drawing of Motor




7.0 Illustrations

Illustration 5 - Drawing of Blade

For Blender




7.0 Illustrations

Illustration 5a - Drawing of Blade

For Coffee Mill




BASIC LISTEE

Address

CountryProduct

MULTIPLE LISTEE 1AddressCountry

Brand Name

ASSOCIATEDMANUFACTURER

AddressCountry

BASIC LISTEE MODELS


Brand Name


Address

Country

BASIC LISTEE MODELS


Brand Name


Address

Country

BASIC LISTEE MODELS

None

9.0 Correlation Page For Multiple ListingsThe following products, which are identical to those identified in this report except for model number and Listeename, are authorized to bear the ETL label under provisions of the Intertek Multiple Listing Program.

Sinsion Technology Industrial Co., Ltd

No. 11, Tongle Rd., Tangxia town, Pengjiang Qu, Jiangmen, Guangdong, China

ChinaROCKET BLENDER

MULTIPLE LISTEE 1 MODELS


None


None




10.0 General InformationThe Applicant and Manufacturer have agreed to produce, test and label ETL Listed products in accordance withthe requirements of this Report. The Manufacturer has also agreed to notify Intertek and to request authorizationprior to using alternate parts, components or materials.

COMPONENTSComponents used shall be those itemized in this Intertek report covering the product, including any amendmentsand/or revisions.

LISTING MARKThe ETL Listing mark applied to the products shall either be separable in form, such as labels purchased fromIntertek, or on a product nameplate or other media only as specifically authorized by Intertek. Use of the mark issubject to the control of Intertek.

The mark must include the following four items:

1) applicable country identifiers "US" and/or "C" or "US", "C" and "EU"2) the word "Listed" or "Classified" or "Recognized Component" (whichever is appropriate)3) a control number issued by Intertek4) a product descriptor that identifies the standards used for certification. Example:

For US standards, the words, “Conforms to” shall appear with the standard number along with the word, “Standard” or “Std.” Example: “Conforms to ANSI/UL Std. XX.”

For Canadian standards, the words “Certified to CAN/CSA Standard CXX No. XX.” shall be used, orabbreviated, “Cert. to CAN/CSA Std. CXX No. XX.”

Can be used together when both standards are used.

Note: A facsimile must be submitted to Intertek, Attn: Follow-up Services for approval prior to use.The facsimile need not have a control number. A control number will be issued after signed CertificationAgreements have been received by the Follow-up Services office, approval of the facsimile of yourproposed Listing Mark, satisfactory completion of the Listing Report, and scheduling of a factoryassessment in your facility.

MANUFACTURING AND PRODUCTION TESTSManufacturing and Production Tests shall be performed as required in this Report.

FOLLOW‑UP SERVICEPeriodic unannounced audits of the manufacturing facility (and any locations authorized to apply the mark) shallbe scheduled by Intertek. An audit report shall be issued after each visit. Special attention will be given to thefollowing:

1. Conformance of the manufactured product to the descriptions in this Report.2. Conformance of the use of the ETL mark with the requirements of this Report and the Certification Agreement.3. Manufacturing changes.4. Performance of specified Manufacturing and Production Tests.

In the event that the Intertek representative identifies non-conformance(s) to any provision of this Report, theApplicant shall take one or more of the following actions:

1. Correct the non-conformance.2. Remove the ETL Mark from non-conforming product.3. Contact the issuing product safety evaluation center for instructions.




10.1 Evaluation of Unlisted Components

Note to Intertek Follow Up Inspector: The Component Evaluation Center, CEC, will notify you in writingwhen these components must be selected and sent to the CEC for re-evaluation

Ship the samples to:Intertek Testing Services Shenzhen Limited Guangzhou BranchETL Component Evaluation CenterBlock E, No. 7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou ScienceCity

CETDD Guangzhou, China.Attn: Ms. Joey KuangSample Disposition: Due to the destructive nature of the testing, all samples will bediscarded at the conclusion of testing unless, the manufacturer specifically requests thereturn of the samples. The request for return must accompany the initial component

shipment.

Because Unlisted Components are uncontrolled, and they do not fall under a third party follow up program,Intertek may require these components to be tested and/or evaluated at least once annually, more often forcertain components, as part of the independent certification process. The Unlisted Components in Section 5.0require testing and/or evaluation as indicated.




Product Test Voltage Test TimeAll products covered by this Report. 1000V 60 s

or1240V 1 s

The test equipment shall incorporate a voltmeter in the output circuit to indicate directly the applied test potentialif the rated output of the test equipment is less than 500VA.If the rated output of the test equipment is 500VA or more, the applied test potential may be indicated by either:1 - a voltmeter in the primary circuit;2 - a selector switch marked to indicate the test potential; or3 - a marking in a readily visible location to indicate the test potential for test equipment having a single testpotential output.In cases 2 and 3, the test equipment shall include a lamp or other visual means to indicate that the test potentialis present at the test equipment output. All test equipment shall be maintained in current calibration.

The test shall be conducted on products, which are fully assembled. Prior to applying the test potential, allswitches, contractors, relays, etc., should be closed so that all primary circuits are energized by the test potential.If all primary circuits cannot be tested at one time, then separate applications of the test potential shall be made.

The test voltage specified below shall be applied between primary circuits and accessible dead-metal parts. Thetest voltage may be gradually increased to the specified value but must be maintained at the specified value forone second or one minute as required.

Test Equipment

11.1 Dielectric Voltage Withstand TestMethod

One hundred percent of production of the products covered by this Report shall be subjected to a routineproduction line dielectric withstand test.

Products Requiring Dielectric Voltage Withstand Test:

The test equipment shall incorporate a transformer with an essentially sinusoidal output, a means to indicate theapplied test potential, and an audible and/or visual indicator of dielectric breakdown.

- Dielectric Voltage Withstand Test- Polarization Test

11.0 Manufacturing and Production TestsThe manufacturer agrees to conduct the following Manufacturing and Production Tests as specified:

Required Tests




Products Requiring Polarization Test:All products covered by this Report.

11.2 Polarization TestMethod

As a routine production-line verification, each cord-connected appliance provided with a 2-wire polarized plug,shall be examined or tested for electrical continuity between the ungrounded circuit supply conductor of theattachment plug (narrow blade) and all components intended to be connected to the ungrounded conductor. Ifthe continuity cannot be readily determined by visual inspection and component checking, an electrical continuitytest is to be conducted.

a) The switch, if employed and b) The thermal protect device, if employed

Any indicating device such as ohmmeter, a battery-and-buzzer combination, or the like, shall be used todetermine compliance with the continuity requirements mentioned above.




Date/ Project Handler/Proj # Site ID Reviewer

None

12.0 Revision SummaryThe following changes are in compliance with the declaration of Section 8.1:

Section Item Description of Change


listing constructional data report (cdr)lhs.pdf · listing constructional data report (cdr) report...

Documents