is 15200 (2002): hydrogen sulphide - code of safety
TRANSCRIPT
Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
इंटरनेट मानक
“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”
“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru
“Step Out From the Old to the New”
“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan
“The Right to Information, The Right to Live”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
“Invent a New India Using Knowledge”
है”ह”ह
IS 15200 (2002): Hydrogen Sulphide - Code of Safety [CHD 8:Occupational Safety, Health and Chemical Hazards]
IS 15200:2002
W?7RTWEF
* ~–qwi--l +-RaT
Indian Standard ~
HYDROGEN SULPHII)E — CODE OF SAFETY,
.
ICS 13.300; 71.060.99
0 BIS 2002
BUREAU OF INDIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
September 2002 Price Group 3
l“
Industrial Safety and Chemical Hazards Sectional Committee, CHD 8
FOREWORD
This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by the industrialSafety and Chemical Hazards Sectional Committee had been approved by the Chemical Division Council.
Hydrogen sulphide is found in volcanic gases and in many spring waters. As a product of putrefaction ofsuIphur containing decaying organic material, it is present in sewer gas and also liberates from waste water oftanneries, glue factories and fertilizer plants. It is also liberated as a by-product of de-hairing and tanningprocess. The unpleasant smell of putrefied hides and rotten eggs is partly due to this gas. Exposure to hydrogensulphide may occur in the production of viscose rayon, sulphur dyes, sulphur, oleum and coke from coal containinghigh sulphur content. The atmosphere usually contains a trace of this gas. It is an important raw material forproducing sulphur and thio-organic compounds. Since long, it is extensively used in the qualitative analysis. Itis also used in production of heavy water.
There is no ISO standard on this subject. In the preparation of this Code of safety, considerable assistance hasbeen derived from the following publications:
a) Chemical Safety Data Sheet SD-36, Hydrogen Sulphide — Manufacturing Chemists Association,Washington.
b) Dangerous Properties of Industrial Materials by Irving Sax VIth Edition.
c) National Institute for Occupational Safety and Health, US Department of Health, Education and Welfare:Criteria for a Recommended Standard on Occupational Exposure to Hydrogen Sulphide, HEWPublication No. (NIOSH) 77-158.
d) Encyclopedia of Chemical Technology — Ulman, 6th Edition.
The composition of the Committee responsible for formulation of this standard is given at Annex A.
Indian Standard
HYDROGEN SULPHIDE — CODE
1 SCOPE
This standard covers properties of hydrogen sulphide,the nature of hazards associated with it and essentialinformation of personal protective equipment, storage,handling, labelling, transport, spillage/leakage, fireprevention and fire fighting, training and healthmonitoring and fmt aid.
2 REFERENCES
The following Indian Standards contain provisionswhich through reference in this text, constituteprovisions of this standard. At the time of publication,the editions indicated were valid. All standards aresubject to revision, and parties to agreements basedon this standard are encouraged to investigate thepossibility of applying the most recent editions of thestandards indicated below:
IS No. Title4155:1966 Glossary of terms relating to
chemical and radiation hazards andhazardous chemicals
4167:1980 Glossary of terms relating to airpollution (first revision)
3 TERMINOLOGY
For the purpose of&is standard, the definitions givenin 1S4155 and IS 4167 shall apply.
4 PROPERTIES
4.1 General Information
4.1.1 Common Names
Hydrogen sulphide, sulphureted hydrogen andhydrosulphuric acid.
4.1.2 Chemical Name
Hydrogen sulphide.
4.1.3 Chemical FormuIa — I+zS.
4.1.4 Molecular Weight — 34.08.
4.1.5 CAS No. — 7783-06-4.
4.1.6 UN NO. — 1053.
4.2 Physical Properties
4.2.1 Description
Colorless flammable gas with a strong offensiveodour of rotten eggs, It is heavier than air and settleson the ground.
IS 15200:2002
OF SAFETY
4.2.2 Boiling Point — -60.4”C.
4.2.3 Melting Point — –85.53°C
4.2.4 Speczjlc Gravity — (18°C/40C) — 1.54.
4.2.5 Vapour Density (Air= 1) — 1.189.
4.2.6 Density of Saturated Liquid — 774 kglm3 at21c10c.
4.2.7 Density of Saturated Vapour—31.04 kglm3 at21.1°c.
4.2.8 Vapour Pressure — 20 atm at 25”C.
4.2.9 Critical Temperature — 100.4”C.
4.2.10 Critical Pressure — 88.9 atm.
4.2.11 Critical Density — 349 kglm3.
4.2.12 Physical Status
Gaseous at ordinary temperature but may exist asliquid at low temperature and high pressure.
4.2.13 Volubility
Slightly so}uble in cold water, 0.32 percent maximumat 26.67°C (m/m), more soluble in alcohol.
4.3 Chemical Properties
4.3.1 Reactivity
In aqueous solution it is weakly acidic in nature andreacts vigorously with nitrogen halides, metal oxides,sodium peroxide and oxidants.
4.4 Explosion Hazard
At elevated temperature, it decomposes to its elementsand may cause bursting of container. Thermaldecomposition is promoted by contact with metal likeplatinum.
4.5 Fire Hazard
4.5.1 Hydrogen sulphide is a flammable gas and burnsin air with blue flame. It may cause fire and explosionwhen exposed to heat, flame or oxidizer. It emits high iytoxic fumes of oxides of sulphur in case of fire.Hydrogen sulphide gas is heavier than air and maytravel considerable distance to a source of ignition andflash back.
4.5.2 Auto Ignition Temperature in Air — 260”C.
4.5.3 Flammable Limits in Air (Percent by Volume) ut20”C:
a) Lower explosion limit (LEL) : 4,3
1
IS 15200:2002
b) Upper explosive limit (UEL) : 46
4.6 Corrosivity
Hydrogen sulphide is a corrosive material. It attacksmany metals, which results in the formation ofsulphide. In presence of moisture and any oxidizingmaterial, it may form sulphuric acid and corrode thecontainers.
5 HEALTH HAZARD
5.1 Hydrogen sulphide can affect the body if it isinhaled or if comes in contact with the eyes, skin, noseor throat. It can also affect the body if it is swallowed.Inhalation of high concentrations of hydrogen sulphidevapour may cause loss of consciousness and death.Inhalation of lower concentrations may causeheadache, dizziness and upset stomach. Exposure tohydrogen sulphide can cause temporary loss of thesense of smell, and irritation of the eyes, nose or throat.The toxic effects of hydrogen sulphide can becategorized as acute effects, sub-acute effects andchronic effects.
The acute toxic effects of hydrogen sulphide in humanpoisoning are summarized in Table 1.
5.2 Toxicity
5.2.1 Threshold Limit Value (TL~ — 10 ppm (15mg/m3) (ACGIH).
5.2.2 Short-Term Exposure Limit (STEL)-- 15 ppmfor 15 min.
5.2.3 Toxic Dose Level (TDL) — 0.0047.
5.2.4 Odour ThreshoId — 0,13 ppm (0.215 mg/m3).
5.2.5 LC50 (inhal-rat) — 444 ppm.
5.2.6 Target Organs — Respiratory organs and eyes.
6 PERSONAL PROTECTION
6.1 Wear impervious clothing to prevent the skincontact from liquid hydrogen sulphide or from contactwith vessels containing liquid hydrogen sulphide.
6.2 Wear splash-proof safety goggles to prevent anypossibility of eye contact where liquid hydrogensulphide is handling.
6.3 Employees should wash promptly when skinbecomes wet.
6.4 Remove clothing immediately that becomes wetwith liquid hydrogen sulphide until the hydrogensulphide is evaporated.
6.5 Respiratory protection is essential to preventinhalation of gas. Minimum respiratory protectionrequired for concentration above 10 ppm are given inTable 2.
6.6 Respirators may be used for operations whichrequire entry into tanks or closed vessels and inemergency situation. The respirator used shall beapproved by the concerned authority.
6.7 Lead acetate paper should be carried along withportable hydrogen sulphide monitor for use wherenecessary.
6.8 Amyl nitrite should be given to the victim forinhalation by crushing the ampule in fkont of nostrilsof the victim.
Table 1 Acute Toxic Effects of Hydrogen Sulphide in Human
(Clause 5.1)
SI Concentration. Durntinnof Exposure CommentsNo. of H2S,ppm .
15min >15min-lh >lh-4h >4-8h
(1) (2) (3) (4) (5) (6) (3)
i) 10 Eye irritation Maximum tolerableconcentration forprolonged exposure
ii) 50-100 Lossofolfactory Eyeirritation Eyeandbronchial Danger in case of Working conditionperception irritation continuousexposure necessitate
protective measuresiii) 150-250 do
Eye and bronchial Serious respiratory Serious respiratorydistress and asthenia distress sod asthenia
doirritation
iv) 300-400 Lossofolfactory Severerespiratory Pulmonaryedema Pulmonary edema Risk of death if noperception eye and distress acute asthenia and risk of death and risk of death appropriatebronchial irritation measures takenasthenia
v) 500-1000 Loss of consciousness Rkk of pulmonary —do
respiratory distress edema and deathvi) >I 000 Immediate loss of consciousnessand respiratorydistress
2
l’!
Table 2 Respiratory Protection forHydrogen Sulphide
(Clause 6.5)
N Condition Minimum RespiratoryNo. Protection Required
Above 10 ppm
(1) (2) (3)
i) Low concentration Anysupplied-airrespirator with a(up to 300 ppm) full faeepiece,helmet or hood
ii) >300 ppm and escap Self-contained breatldngfrom unknow apparatus with a fill facepiececoncentration operated in pressure demand or
other positive pressure mode
7 STORAGE/HANDLING
7.1 Storage
7.1.1 Anhydrous hydrogen sulphide does not reactwith steel at ambient temperature. However, in aqueousmedium, the hydrogen generated by reacting with ironcan diffuse in the metal causing blistering andembrittlement. The degree of corrosion depends uponthe quality of steel and is very limited with stainlesssteel. Ferritic steel is much more sensitive to hydrogenembrittlement than austenitic steel. Residual stress ofhigh strength steel for storing hydrogen sulphide is tobe relieved after welding otherwise it is likely to crackunder stress.
7.1.2 The use of copper and its alloys are to beprohibited.
7.1.3 Storage area should be well ventilated, and ifpossible, equipped with a watercooling system in caseof tire.
7.1.4 Hydrogen sulphide should be stored separatelyfrom incompatible products (oxidizing agents,inflammable materials, etc).
7.1.5 Area should be declared as ‘NO SMOKINGAREA’.
7.2 Handling
Personal protective wears are to be used invariablywhile hartdling hydrogen sulphide.
7.3 Labelling
All containers should bear an identifying label as perthe provision of prevailing relevant regulationsindicating that the contents are highly flammable andtoxic. The label should also list the special risks andinclude cautionary advices.
7.4 Transportation
7.4.1 Hydrogen sulphide is flammable and toxic. ItsUN No. is 1053, UN hazard Class 2, 3 and 6.1,
IS 15200:2002
7.4.2 The Rules and Regulations for transportation ofhazardous chemicals shall be adhered to.
8 SPILLAGE/LEAUGE AND DISPOSAL
If hydrogen sulphide is spilled or leaked, the followingsteps should be taken:
a) Remove all ignition source;
b) Ventilate area of spill or leak to disperse gas;
c) If in the gaseous form, stop flow of gas. Ifsource of leak is a cylinder and the leakcannot be stopped in place, remove theleaking cylinder to a safe place in the openair, and repair the leak or allow the cylindersto empty; and
d) If in the liquid form, allow to vaporize.
9 FIRE PROTECTION AND FIRE FIGHTING
9.1 Stop flow of hydrogen sulphide gas.
9.2 Carbon dioxide and alcohol foam type ofextinguisher should be used for fire fighting.
9.3 Fire fighting personnel should have the requiredself-contained breathing apparatus with a full facepieceoperated in pressure demand or other positive pressuremode.
10 TRAINING AND HEALTH MONITORING
10.1 Training
10.1.1 Safety in handling depends to a great extentupon the effectiveness of employees education and
training.
10.1.2 Employees should be familiar with itsflammable and toxic properties.
10.1.3 Continuous training and restraining should bedone in the safe handling procedures.
10.2 Health Monitoring
10.2.1 During pre-employment medical check up,examination of the eyes and lungs should be stressed.The following procedures should be made availableto each employee who is exposed to hydrogen sulphideat potentially hazard levels:
a)
b)
A complete history andphysical examination— The purpose is to detect pre-existingconditions that might place the exposedemployee at increased risk and to establish abaseline for future health monitoring.
Eye disease — Hydrogen sulphide is a severeeye irritant and may cause tissue damage.Those with pre-existing eye problems maybe at increased risk from exposure.
3
IS 15200:2002
c) 14 “-1 7“’chest roentgenogram — Hydrogensulphide may cause human lungs damage.Surveillance of the lungs is indicated.
d) FVC and FEV (1 See) — Hydrogen sulphideis a respiratory irritant. Persons with impairedpulmoqary function maybe at increased riskfrom exposure. Peridic surveillance isindicated.
10.2.2 Periodical medical examination should be doneon annual basis for all the above mentioned criteria,except that an X-ray is considered necessary only whenindicated by the results of pulmonary function testing,or by signs and symptoms of respiratory diseases.
11 FIRST AID
11.1 Eye Contact
11.1.1 [f liquid hydrogen sulphide gets into the eyesimmediately wash the eyes with large quantity of waterfor at least 15 rein, occasionally lifting the lower andupper lids.
11.1.2 Get medical attention immediately.
11.1.3 Contact lenses should not be used when workingwith this chemical.
11.2 Skin Contact
11.2.1 If liquid hydrogen sulphide gets on the skin,immediately flush the contaminated skin with water.
11.2.2 If it soaks through the clothing, immediatelyremove the clothing and flush the skin with water.
11.2.3 If irritation persists afier washing, get medicalattention.
11.3 Inhalation
11.3.1 If a person breathes in large amount of hydrogensulphide move the exposed person to fresh airimmediately and administer oxygen if available.
11.3.2 If breathing has stopped, give artificialrespiration.
11.3.3 Keep the affected person warm but not hot andat rest.
11.3.4 Get medical attention as soon as possible.
I I
IS 15200:2002
ANNEX A
(Foreword)
COMMITTEE COMPOSITION
Industrial Safety and Chemical Hazards Secitonal Committee, CHD 8
Organization
National Safety Council, Mumbai
Airports Authority of IndlANew DclhI
Atomic EnergyRegulatoryBoard, Mumbai
BhabhaAtomic ResearchCentre,Mumbai
Central Boiler Board,New Delhi
Century Rayon, Tharre
Central LeatherResearch Institute,Chennai
Central Mining ResearchInstitute,Dhanbad
Central WarehousingCorporation,New Delhi
Confederationof Indian Industries,New Deihi
Departmentof Explosives,Nagpur
Department of IndustrialPolicy&Promotion, New Delhi
DevelopmentCommissioner(SS1),New Delhi
Dkectorate Gtneral of Health Services,New Delhi
DirectorateGeneral Factory Advice Servicesand LabourInstitutes,Mumbai
Directorateof Industrial Safety and Health (Factory Inspectorate),Mumbai
DirectorateGenerrdof Mhres Safety,Dhanbad
EmployeesS&&InsuranceCorporation,New Delhi
Excel IndustriesLimited, Mumbai
HindustanAeronauticsLimited, Bangalore
HlndustanLever Limited, Mumbai
Indian lnstitutcof ChemicalTechnology,I-iydembad
IndianChemical ManufacturersAssociation,Mumbai
IndianDrugs and PharmaceuticalsLimited,RNrikesh
IndianPetrochemicrdCorporationLimited,Vadodara
Indian SpaceResearchOrganization,Sriharikota
IndustrialToxicologyResearchCentre,Lucknow
Ministryof Defence(DGQA),New Delhi
Ministryof Defence,Dkcctorate of Standardization,New DeJhl
Ministryof Defence(OFB), Kolkata
Representative(s)
Sm K.C. -A (Chsdrmn)
~AIN@
StrruP.K.Gsrosa
IhB.N. Rmm
~ATSVS
SrrrrrH.G. LJmmicxmrmmrrSrnuS. K. Mrwm (Alternate)
REH@ENTATNS
SrnrtJ.K. PANOSV
~AIWE
REHWEIWATNE
~ATNS
DRD.R Cr+.ww
k3W5FNTATIW
bWZJ3XTATIVS
DrtA.K. IvhrumMSsnuS. P. RANA(Alternate)
~AllVE
~R OFhhr?s S~ (MSE)Dasurv hIUXtVROFMaws S.wr?m(I-IQ)(Alternate)
~ATNE
SrmiVrrmB. IMsrn
~A~
Sm B. B.DAVE%tru&rnYAJHAvAR(A&rrate)
Smas. vmxmEawARAluo
SrnuV.N. DNSrnuA. A. Ptwwma (Akmrate)
~ATIVS
%llUp.VUAWl,@iAVANSmoM. R. PAma,(Alternate ~
Smu A. V. S.m+m (Aknate II)
SrnuP.N. S~SrrraV.K.SSUVASTAVA(Alternate)
DRvrRENLrRAMssaADRV.P. Ssrmmm(Alternate)
Smr M.S. Sr.a-TMSmuSumGOSH(Alternate)
%Up. S. /ii+uJALT-COL‘fmwm Smcw(Ahernate)
DRD.S. S. GmrormYSrauR. .%UNWASAN(Alternate)
-,-
(Continued on page 6)
5
f,-7
1S 15200:2002
(Continuedfrom page 5)
Organization
Ministry of Dcfence (R&D), Kanpur
Mhsistryof Environment &Forest New Delhi
National Institute of Occupational Heaftb,Ahmedabad
National Grganic Chemical IndustriesLimited, Thane
National Safety Council, Mumbai
Gil Industry Safety Dkcctorate, New Delhi
SaferyAppliancesManufacturers’Association,Mumbai
Standing Fire Advisory Council, New Delhi
Steel Authority of India Limited, Ranchi
SIEL Chemical Complex, New Delhi
Southern PetrochemicalIndustriesCorporationLimited,Tuticorin
Tata AfG Rkk Management Services Limited, Mumbsd
BIS Dkectorate Generrd
Representative(s)
Ds A.K. SAXSNADs R.4mrw Snmr (Mternde)
~AIWE
RHREWIWATIVE
DRB.V. BAPATWasV. R.NASLA(/4fternate)
SNRSP.M. RAOWinsD. BISWAS(Akvrrate)
Smu S. K.CHAXRASARTISmr V.K.SIUVASTAVA(Alternate)
f@SBENTAIIVS
RHWSENTAYIVE
SmuV.JAYASAMANSmuS.MuarJGANANDAM(Ahenrote)
SmuURMSSHD.SHAH
SHRIS. K.C~rJOHORI,Director& Head (CHD)~epresenting DirectorGeneral (Ek-oficio)]
Member .!kcretkyySHIUN.K. PAL
Dkector (CHD), BIS
iii
6
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promoteharmonious development of the activities of standardization, marking and quality certification of goodsand attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in any formwithout the prior permission in writing of BIS. This does not preclude the free use, in the course ofimplementing the standard, of necessary details, such as symbols and sizes, type or grade designations.Enquiries relating to copyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewedperiodically; a standard along with amendments is reaffiied when such review indicates that no changes areneeded; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standardsshould ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of‘BIS Catalogue’ and ‘Standards: Monthly Additions’.
This Indian Standard has been developed from Doc : No. CHD 8 (896).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS
Headquarters :
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002 Telegrams : ManaksansthaTelephones :3230131,3233375,323 9402 (Common to all offices)
Regional Offices : Telephone
Central :
Eastern :
Northern :
Southern :
Western :
Branches :
Manak Bhavan, 9 Bahadur Shah Zafar Marg
{
3237617NEW DELHI 110002 3233841
1/14 C.I.T. Scheme VII M, V. L P. Road, Kankurgachi{
3378499,3378561KOLKATA 700054 3378626,3379120
SCO 335-336, Sector 34-A, CHANDIGARH 160022
{
603843602025
C.I.T. Campus, IV Cross Road, CHENNAI 600113
{
2541216,25414422542519,2541315
Manakalaya, E9 MIDC, Marol, Andheri (East){
8329295,8327858MUMBAI 400093 8327891, 8327892
AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD.GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHAPATNAM
Reprography Unit, BIS, New Delhi, Indim
1 --’