INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE I~PPLIANCE

THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE.

INSTALL OR SERVICE THIS RANGE.ccccccccc ccccc ccccc

~

ADJUSTMENt ALTERATION SERVICE

CLEARANCE DIMENSIONS

For complete information in regard to installation of range. see figures 1 and 2 on page 2. For SAFETYCONSIDERATIONS, do not install a range in any combustible cabinetry which is not in accord with the installationclearances shown in figure 1 on page 2.

CAUTION: SOME CABINETS AND BUILDING MATERIALS ARE NOT DE:SIGNED TO WITHSTANDTHE HEAT PRODUCED BY THE NORMAL SAFE OPERATION OF A LISTED APPLIANCE.DISCOLORATION OR DAMAGE, SUCH AS DELAMINATION, MAY OCCUR.

8101P120-60(03-95-00)

cA. Do not attempt to operate this oven with the door opensince open-door operation can result in harmfulexposure to microwave energy. It is important not todefeat or tamper with the safety interloc:ks.

B. Do not place any object between the oven front faceand the door or allow soil or cleaner residue toaccumulate on sealing surfaces.

D

Do not operate the oven if it is damaged. It isparticularly important that the oven door closeproperly and that there is no damage to the: (1) Door(bent), (2) hinges and latches (broken or loosened),(3) door seals and sealing surfaces.

The oven should rlot be adjusted or repaired byanyone except properly qualified service personnel. I

IMPORTANT -PLEASE KEEP FOR THE USE OF THE LOCAL ELEC:TRICAL INSPECTOR.

"A" = 30 inches minimum clearance between the top of the cooking surface and thebottom of an unprotected wood or metal cabinet, or "A" = 24 inches minimum whenbottom of wood or metal cabinet is protected by not less than 1 /4-inch thick flame-retar(jant millboard covered with not less than No. 28 MSG sheet steel, 0.015-inchthick stainless steel, 0.024-inch thick aluminum, or 0.020-inch thick copper.

To eliminate the risk of burns orfire by reaching over heated surface units, cabinetstorage space located above the surface units should be avoided. If cabinet storageis to be provided, the risk can be reduced by installing a range hood that projectshorizontally a minimum of 5 inches beyond the bottom of the cabinets.

1, 2, 3 -COMBUSTIBLE BUILDING WALLS.4 -COMBUSTIBLE WALL CABINET.

A FREE-STANDING RANGE MAY BE IN~)TALLED ADJACENT TO (0" FROM) COMBUSTIBLE WALLS 1, 2 & 3

-2-

1611

"j 25 II NORMA L

COUNTER~ TOP DEPTH

2411 CAB I NETDEPTH. I

36'1 COUNTERTOP HEIGHT 5 3/411

"""-3011 CAB I NET

OPENINGS.UPPER & LOWER

~~

"'-

PROVIDE FOR 120/240 VOLTOUTLET IN THIS AREA.

r'

FIGURE 2

Electric Free-Standing Ranges

-3-

The installation of a range designed for mobile homeinstallation must conform with the Manufactured HomeConstruction and Safety Standard, Title 24 CFR, Part 3280(formerly the Federal Standard for Mobile HomeConstruction and Safety, Title 24 HUD, Part 280) or, whensuch standard is not applicable, the Standard forManufactured Home Installations 1982 (ManufacturedHome Sites, Communities and Set-Ups), ANSIA225.1-1984, or with local codes.

Place range where it will be well lighted. Do not set rangeover holes in the floor or other locations where it may besubject to strong drafts. Any opening in the wall behind therange and in the floor under the range should always besealed. Make sure the flo~' of combustion or ventilation air isnot obstructed.

B.WARNING: A risk of range tip-overexists if the applianceis not installed in accordance with the installationinstructions provided. The proper use of this deviceminimizes the risk of TIP-oVER. In using this device theconsumer must still observe the safety precautions as statedin the USE and CARE MANUAL and avoid using the ovendoor and/or lower drawer as a step stool.

Cement or Concrete Construction:1. Suitable screws for concrete construction can be

obtained at a hardware store. Drill the required sizehole forthe screws obtained into the concrete at thecenter of the hole:s identified in figures 3 through 6,as applicable, as "holes for floor." Secure theANTI-TIP bracket to the floor. Proceed to STEP 3.

Installation instructions are provided for wood and cementinstallation in either floor or wall. Any other type ofconstruction may require special installation techniques asdeemed necessary to provide adequate fastening of theANTI-TIP bracket to the floor or wall. The bracket may beinstalled to engage the left or right rear levelin!~ leg.

STEP 3 -Range Installation

A. Complete the installation of the range per the installationinstructions provided \Nith the product.

B. Align the range to its designated location and slide itback into position. Make sure that the leveling foot is fullyinserted into and secured by the ANTI-TIP bracket.Note: A minimum clearance of 1/4" is required betweenthe range and the leveling foot that will engage theANTI-TIP bracket, see figure 7 or 8.

STEP 1 -Locating The Bracket (see figure 3)Installations with flush mount wall outlet

A. Mark the floor or wall where either the right or left rear"EDGE" of the range is to be located.

B. Place the BRACKET 15/16" from the marked "EDGE"toward center of opening and against the back wall asshown in figure 3.

C. Use the bracket as a template and mark the requiredholes, as shown in figure 3, for the type of constructionyou will be using.

CAUTION: Damage to the range may occur if range ismoved or lifted by grasping the main top or backguard.

c

D

All free-standing ranges with a glass top have a non-lift-up top. Coil tops are lift-up.

For SAFETY CONSIDERATIONS as well as optimumperformance adjust the range so that it is level. This maybe checked by placing a spirit level or a large pan ofwater on the cooktop or the oven rack. If an adjustmentis required pull the range forward, tip the range androtate the leveling feet as required.

Eo To check the range for proper installation of the anti-tipbracket: Use a flashlight and look underneath thebottom of the range to see that one of the rear levelinglegs is engaged in the bracket slot.

F. Proceed with the Iremainder of the installationinstructions provided with the range.

Installations with alternate outlet locations (see figures4 through 6.)

A. Mark the floor or wall where either right or left rear"EDGE" of the range is to be located.

B. Place the bracket 15/16" from the marked "EDGE"toward the center of opening and against the spacer asshown in figures 4 through 6, as applicable. (See figures4 through 6 for information on appropriate spacer sizes.See figure 8 for information on securing of spacer.)

C. Use the bracket as a template and mark the requiredholes, as shown in figure 4 through 6, for the type ofconstruction you will be using.

STEP 2 -Anti-Tip Bracket Installation

A. Wood Construction:

1. Floor: Locate the center of the two holes identified in

figures 3 through 6, as applicable, as "holes forfloor." Drill a 1/8"pilot hole in the center of each hole(a nail or awl may be used if a drill is not available.)

Secure the ANTI-TIP bracket to the floor with thetwo screws provided. Proceed to STEP 3.

2. Wall: Locate the center of the two holes identified in

figures 3 through 6, as applicable, as "holes forwall." Drill an angled 1/8" pilot hole in the center of

each hole as shown in figure 7 or 8 (a nail or awl maybe used if a drill is not available.) Secure theANTI-TIP bracket to the wall with the two screws

provided as shown in figure 7 or 8. Proceed to STEP

3.

-A.-

\.../~' "

~

~III

""."1.1.

\MARKED EDGEOF RANGE \

.,--,3(1

3 1/2,,1

"'",. ..-ANTI-TIPBRACKET

HOLES FOR-J'" ""- -15/16" FRO~ EDGE OF RANGEFLOOR'" , ~

~ARKED EOOE '~OF RANGE FIGURE 6

NOTE: USE A MINIMUM OF (2) SCREWSTO INSTALL BRACKET TO THEWALL OR FLOOR.

""'---,.-

BRACKET - SCRI:WS MUST~NTI:R WOOD ORNET~\L

"" NAILED TOWALL PLATE

-WALL PLATE

"-1/4"MlN.

SlIDE IN TO SECURE

~~

~

><./ 1./

~

'-~---

ART,A219-761B ART .$21$-$20-AUSE A MINIMUM OF TWO (2)10d x 3" LONG NAILS O~LONG SCREWS TO ANCHORSPACER TO WALL. PLATE.

FIGURE 8FIGURE 7

-5-

~3/8. SPACER BLOCK WI LLREQUIRED BEHIHD THE AHTIBRACKET. NAI L DR SCREW \WJOOEN \

sPACER BLOCK CNOT PROVIDED)LTO WALL STRUCTURE. r L

..2 NAILS OR SCREWS

~~;~~~~~~8 " /: ?' ~~~

LOOR

--~--":ATTACH TIE-oO~ BRACKETWITH LDNG SCREWS.

~OLES FOR WALL

~EVEL I NG FOOT

WOODEN SPACER

RANGE ANTI-TIP~ nlBOTTOM BRACKET --'1 rSCREW BRACKETTO SPACER

SLIDE IN TO~

OUTSIDE WIRINGYour local utility company will tell you whether the presentelectric service to your home is adequate. It may benecessary to increase the size of the wiring to the house andservice switch to take care of the electrical load demandedby the range. The kilowatt rating forthe range is specified onthe name plate on the range.

wire plug-in outlet placed at a convenient point near theback of the range. The range is then connected to this outletthrough an approved service cord (pigtail) fastened securelyto the terminal block with proper strain relief at the range anda three or four pronged plug at the opposite end.

RANGE CONNECTIONSOn models using service cords (Pigtail) the front surface ofthe range outlet must be mounted flush to wall. See figures10A and 10C.

HOUSE WIRINGMost local Building Regulations and Codes require that allelectrical wiring be done by licensed electricians. All wiringshould conform to Local and National Electrical Codes. Thisrange requiresasingle phase three wire 120/240 volt,60 Hz,AC circuit. Wiring codes require a separate circuit be runfrom the main entrance panel to the range and that it beequipped with separate disconnect switch and fuses, eitherin the main entrance panel or in a separate switch and fusebox. In some communities, a solid or flexible continuousarmored conduit must be used from main entrance panel tothe terminal box on the rear of the range. Others will permitthe termination of the range circuit at a polarized three orfou r

On models not provided with a service cord and modelshaving a conduit, connection to the power supply isnecessary. REMEMBER -mobile homes and some LOCALCODES DO NOT PERMIT GROUNDING THROUGHNEUTRAL. Hence, 4-wire service MUST be provided forsuch installations. All others permit 3-wire service, useCOPPER WIRE ONLY. Make connections as explainedbelow and with reference to the appropriate illustration. (Seefigures 10A thru 100). After installation, insure tightness ofall electrical connections and replace all covers.

NOTE: For cord replacement -ONLY a power supply cordrated at 240 volts minimum, 40 amperes or 50 amperespower supply cord that is marked for use with nominal 1 3/8"(34.93 mm) diameter connection opening, with closed loopterminals and marked for use with ranges shall be used.

.0'. RAISE FRCWT r:I'" RAIa -SLIOC TI£ BASE COVER (C1>TI~EOOIP1£NT) LIa"R TIE LEG LEVELERS (SEE ILLUSTRA TICW) .

-INSTALLATION OF FRONT FLOOR COV£R-OPTIONAL EOUIPMENT

-6-

ELECTRIC SUPPLYThe range must be installed in accordance with Local andNational Electric Code (NEC) ANSI/NFPA No. 70-1993.See rating plate on front of range for total connected kw

rating.

,. A£U6'T TIE REAR LEG LEVELE/?S TO TIEl/? C{RRECT fEIGHT.

2. A£U6'T TIE FRCWT LEG LEVELE1?S TO AN APPROX. fEIGHT.

3. POSITlOO TfE /?AIa' IN TJo£ CUTOOT.

4. MAKE FINAL AD.AJST~NT TO FroYT LEG LEVELERS.

3. Both the white wire and the uninsulated (bare) wire fromthe conduit should connect to the white service wire asshown. The bare wire is the range chassis ground.

Remove terminal block access cover from range back. (Seefigure 9).

For service cord (pigtail) use, remove knockout ring fromconduit plate. (See figures 10A and 10C).

4-WIRE SERVICE CORD INSTAllATION(MOBILE HOMES) FIGURE 1 DC

1. The copper ground strap connected between the neutral(middle) post of the main terminal block and the chassisMUST be removed and discarded. Keep the greenground screw. Only a 4 conductor cord should be used.

2. The green wire from the service cord must connect to therange chassis using the green ground screw.

3. The white wire of the service cord must connect to theneutral (middle) post of the main terminal block. Theother two wires of the service cord connect to the red andblack posts of the main terminal block, respectively.

4. Position the strain relief with flanges on top of conduitplate as shown and secure to service cord.

4-WIRE CONDUIT INSTAllATION(MOBILE HOMES) FIGURE 100

1. The range conduit must be routed and properlyconnected to an approved electrical junction box behindthe range.

2. The red and black wires from the range conduit mustrespectively connect to the red and black service wires.An approved wire connector must be used.

3. The white wire from the conduit must be connected to thewhite service wire.

4. The uninsulated (bare) wire from the conduit must beconnected either to a green or bare service wire.

3-WIRE SERVICE CORD INSTAllATIONFIGURE 10A

1. Insure that the copper ground strap IS CONNECTEDbetween the middle post of the main terminal connectionblock and the range chassis.

2. The middle wire of the service cord MUST connect to theneutral (middle) post of the main terminal connectionblock. The other two wires of the service cord connect tothe outside posts of the main terminal connection block.Polarity is unimportant.

3. Position strain relief with flanges on top of conduit plateas shown and secure to service cord.

CONVERSION FRO~t 3-WIRE TO 4-WIRESERVICE(Free-Standing Models Only With 3-Wire Service Cord

Attached).Disconnect range from power. Remove the access cover onback of range and remove the 3-wire service cord from themain terminal block. Follow instructions as outlined in figure10C to connect the 4-wire service cord.

NOTE: Cord replacement -ONLY a power supply cordrated at 240 volts minimum, 40 amperes or 50 amperespower supply cord that is marked for use with nominal 1 3/8"(34.93 mm) diameter connection opening, with closed loopterminals and marked for use with ranges shall be used.

3-WIRE CONDUIT INSTAllATIONFIGURE 10B

1. The range conduit must be routed and properlyconnected to an approved electrical junction box behindthe range.

2. The red and black wires from the range conduit mustrespectively connect to the red and black service wires.An approved wire connector must be used.

-7-

FIGURE 10ANORMAL -3 WIRE PLUG

FIGiURE 108NOR~IIAL -3 WIRE CONDUIT

RED-,

--~r-~~~._.:~ ~.: ANGE CONDU I T

.-~APPROVED~- CONNECTOR

RED

WHITEAPPROVED CONNECTORS

ACKA,APPROVED BOX'"

~

L 1 (RED)~V~

NEUTRAL

GROUND

2 (BLACK)ART.

9219-749-A

CIRCUIT(POWER SUPPLY)

WIRING METHOD IF CODE DOESNOT PERMIT GROUNDING THROUGHNEUTRAL CONDUCTOR & ALSOREQUIRED IN MOBILE HOMES.

FIGURE 10DMOBILE HOME: -4 WIRE CONDUIT

FIGURE 10CMOBILE HOME -4 WIRE PLUG

-8-