immo integrated in ic

7/28/2019 Immo Integrated in IC

1/3

Determining IMMO-ID & VIN (ECU)[Select][01 - Engine]Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.[Close Controller, Go Back - 06]

---OR---

[Select][01 - Engine][Meas. Blocks - 08]Select Block 081.[Go!]The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..[Done, Go Back][Close Controller, Go Back - 06]

Determining IMMO-ID & VIN (Instrument Cluster)[Select][17 - Instruments]Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.[Close Controller, Go Back - 06]

---OR---

[Select][17 - Instruments][Meas. Blocks - 08]

Select Block 081.[Go!]The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..[Done, Go Back][Close Controller, Go Back - 06]

Instrument Cluster Swapping (Used Cluster)Prerequisites:

The NEW (USED) cluster is installed in the car.Battery voltage at least 12.0 V.All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for theinternal installation list since they do not have address 19-CAN Gateway. If inquestion, run a complete Adaptation Control Module Map with the old module installed.


2/3

Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.Make sure to have the Radio Code (for factory radios only).

[Select][17 - Instruments]

[Login - 11]For the following procedure, use the PIN of the NEW (USED) instrument cluster.There are 2 possibilities how to enter a PIN, choose the one that applies for you.

4-digit PINEnter zero followed by the 4-digit PIN directly in the Login field. For example,if your PIN is 1234, enter 01234.If you have a 4-digit PIN then you would NOT use the 7-digit PIN/SKC button at all[Do it!]---OR---

7-digit PIN[Use 7-digit PIN/SKC]Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, alongwith the Workshop Code (WSC) and the Importer number of the dealer that generated the code.[OK]VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".[Do it!]

[Adaptation - 10]

Enter 050 in "Channel Number".[Read]For the following procedure, use the PIN of the OLD (ORIGINAL) instrument cluster.There are 2 possibilities how to enter a PIN, choose the one that applies for you.

4-digit PINEnter zero followed by the 4-digit PIN directly in the New Value field. For example, if your PIN is 1234, enter 01234.If you have a 4-digit PIN then you would NOT use the 7-digit PIN/SKC button at all

[Test][Save][Done, Go Back][Close Controller, Go Back - 06]---OR---

7-digit PIN[Use 7-digit PIN/SKC]Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along


3/3

with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.[OK]VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".[Test][Save][Done, Go Back][Close Controller, Go Back - 06]

Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.

Proceed with Key Matching now.Special NotesInstructions for mileage entry on a new instrument cluster can be found here: Pr

ocedure for installing a NEW Instrument Cluster in vehicles with Immobilizer IIIPlease note the Country Coding and Kilometer -or- Mile units prior to saving theadaptation value!

immo integrated in ic

Documents