Descriptionillmod 600 is an impregnated, pre-compres-

sed foam sealing tape for sealing joints and

connections in structural engineering against

driving rain and has proven in-service perfor-

mance since 1965.

The product is continually monitored in-hou-

se and by independent bodies to guarantee

its consistently high quality.

MaterialOpen-cell polyurethane soft foam, impregna-

ted with flame retardant synthetic resin.

Colour

• anthracite

• grey

Product advantages

• 10 year “i3” performance guarantee*

• 600 Pa after 10 years’ exposure to the

elements, tested at the MPA (Materials

Testing Institute) Hanover

• since 1999, BG1 tested according to DIN

18 542

• UV resistant, water vapour permeablei

• CE Certification (ETA 05/0058) since 2005

DesignRolled product, pre-compressed, and self-ad-

hesive on one side.

* Under the conditions specified by the manufactu-

rers. Only valid on receipt of the correct registration

documents in accordance with terms and conditi-

ons, available on request.

illbruckillmod 600

06/0

6

illbruck illmod 600

DIN Classification

Class of building materials 4102 B1 (low combustibility), P-NDS 04-229

Thermal conductivity 52612 λ10 � 0,055 W/m • k

Evaporative resistance value EN ISO 12572 µ � 100

Temperature resistance -30°C až +90°C

Root resistance 4062 complies with requirements

Porosity of joints EN 1026 a � 0,1 m3/[h • m • (daPa)n]

Resistance to weathering 18542 complies with requirements

Grouping according to 18542 BG1

Resistance to driving rain EN 1027 Requirements fulfilled up to 600 Pa

Compatibility with other 18542 iron, zinc, steel, galvanised sheet iron, aluminium

building materials and copper show no signs of corrosion. Concrete,

foam concrete, brick, chalky sandstone, hard

PVC, Plexiglas and wood show no detrimental

effects. Other materials on request.

Durability 10 year warranty*

Storage period 2 years

Storage temperature + 1°C to + 20°C

Technical data

Window connecting joint

sealing system complete

with 10 year guarantee.*

Joint depth Application Contentarea/ Box

joint width*

(mm) (mm) (m)8 2 462.50

10 375.00

15 250.00

20 187.50

8 3 370.00

10 300.00

15 200.00

20 150.00

12 3 - 7 200.00

15 160.00

20 120.00

15 5 - 10 112.00

20 84.00

ToolsA tape measure, thin bladed trowel, scissors

or knife, and possibly wooden wedges are

required for installation.

Application

• Calculate the width of the joint and select

the tape size using the above table as

a guide.

• Trim and remove the over-compressed

start or end piece.

• Allow at least an extra 1 cm/m when

cutting the tape into lengths.

• For vertical joints, begin installation at the

bottom. The ends of the tape should be

tightly butt jointed.

• The sides of the joints should run parallel

(max. deviation 3 degrees). Most of the

building detritus and mortar residue must

be removed from the sides of the joints.

• The tape must be located 2 mm back

from the front edge of the joint to prevent

over-expansion.

• Wet joints can neutralise the selfadhesive

which is used as an installation aid.

In such a case, illmod 600 can be held in

place with wedges until it has expanded.

• If the product is in contact with paints,

coatings, sealing materials and natural

stone, please enquire about compatibility.

Installation Tips for Windows

• illmod 600 must not be applied around

the corner of the window frame (Fig. 1).

• The tapes must be spliced flush with

a tight butt joint (Fig. 2).

Installation Tips for Cross-jointsEnsure that the surface of the cross joint

between the vertical and horizontal sealing

tape is flush using a tight butt joint.

Installation Tips for MassiveStructures

• Spacers or shims must be used when

installing finished parts to prevent exces-

sive compression of the illmod tape.

• For highly absorbent materials, it is

recommended to apply a waterrepellent

finish to the sides of the joint before

installing illmod 600.

• The self-adhesive surface must be inser-

ted face downwards if the tape is installed

horizontally.

NoteWeigh down the remaining rolls in the opened

boxes to prevent the rolls from rising at the

sides (telescoping). The tape must not come

into contact with solvents or aggressive

chemicals.

Fig. 1: Corner application for window installation Fig. 2: Butt joint for window installation

illbruckillmod 600

Tremco illbruck s.r.o.Úvalská 737/34, 100 00 Praha 10tel.: +420-296 565 333fax +420-296 565 300http://www.tremco-illbruck.come-mail: prodej@tremco-illbruck.com

Supplementary informationThis information must be regarded as general guidelines only. Since we are unable to influence the

use and application conditions, and due to a large variety of all sorts of materials, the user should

always carry out tests to check the suitability of the material for the relevant application.

Manufacturer’s information as at June 2006. We reserve the right to make technical changes.

ServiceOur company is always prepared to provide

technical consultancy services and support.

If you have any queries, do not hesitate to

contact us.

Joint depth Application Contentarea/ Box

joint width*

(mm) (mm) (m)15 7 - 12 86.00

20 64.50

20 8 - 15 49.50

30 33.50

20 10 - 18 97.50

25 78.00

30 65.00

30 13 - 24 52.00

40 36.40

35 17 - 32 32.00

40 28.00

40 28 - 40 18.90

50 16.00

Dimensions

* Movements of components and temperature-induced changes in lengths must also added to the existingwidths of the joints. Dimensional tolerance in accordance with DIN 7715 P3.