hse requirements
TRANSCRIPT
HSE REQUIRMENTS & GUIDLINES
FOR
WELL LOCATIONS AND ACCESS ROADS
CONTRUTION WORK IN TAL BLOCK
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 2 of 24
CONTENTS
1. INTRODUCTION--------------------------------------------------------------------------------------------------1
2. POLICY AND RESPONSIBILITIES--------------------------------------------------------------------------1
3. PERSONNEL-------------------------------------------------------------------------------------------------------4
4. HSE WORKSHOP, AWARENESS AND TRAINING----------------------------------------------------6
5. PROJECT HSE PLAN-------------------------------------------------------------------------------------------6
6. LEGAL AND OTHER REQUIREMENTS-------------------------------------------------------------------8
7. PERSONAL PROTECTIVE EQUIPMENT (PPE) -------------------------------------------------------10
8. OCCUPATIONAL HEALTH REQUIREMENTS---------------------------------------------------------11
9. HSE REQUIREMENTS – CAMPS & WORKSHOPS--------------------------------------------------13
10. ENVIRONMENTAL REQUIREMENTS--------------------------------------------------------------------16
11. JOURNEY MANAGEMENT & DRIVING-----------------------------------------------------------------17
12. EQUIPMENT AND TOOLS-----------------------------------------------------------------------------------19
13. HSE REPORTING-----------------------------------------------------------------------------------------------21
14. EMERGENCY RESPONSE AND MEDICAL EVACUATION----------------------------------------21
15. INFORMATION / DOCUMENTS REQUIRMENTS------------------------------------------------------22
16. COMMITMENTS-------------------------------------------------------------------------------------------------23
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 3 of 24
1. INTRODUCTION
This document is being issued with the Letter of Invitation to Tender and Contract Document
for Well Locations & Access Roads Construction in TAL Block. It sets out the requirements
for Health, Safety and Environment that the bidders are expected to meet and the final
contract awardees is expected to implement as a minimum acceptable standard during the
execution of the works.
1.1 SCOPE AND OBJECTIVES
The document is intended as a guideline for the prospective contractor of Well Locations and
access roads Construction to enable them to prepare their bid in manner that will allow the
Company to evaluate their capabilities to meet or exceed all of the Company HSE
requirements. It does not absolve the Contractors and the prospective Contractor from their
own HSE responsibilities and is not universal in nature.
The document will help the Contractors in preparing their bids for this service and will provide
MOL Pakistan with enough information to objectively evaluate the bids on HSE issues.
The successful bidder will also be able to use this document to prepare its Project HSE Plan
& Procedures in line with the corresponding MOL Pakistan current procedures.
2. POLICY AND RESPONSIBILITIES
2.1 HSE Policy
Contractor and its sub Contractors will acknowledge Company’s strong commitment to HSE
and affirm that they have written health, safety and environmental policies, which are of a
standard comparable to that of company. These policies will be signed and actively
supported and endorsed by Contractor’s management. Contractor will further affirm that its
policies are widely disseminated and understood among employees and sub Contractor's
employees. These policies should be in English and such other local languages as required.
Contractor’s health, safety and environmental policies should include a description of
Contractor’s organization, procedures, responsibilities and methods of communication to and
from personnel.
2.2 Policy Dissemination
Contractor shall outline its scheme for the dissemination of its operational health, safety,
environmental policies to employees at all levels. This shall include general training other
than specifically job-related (e.g. in fire fighting, hygiene etc.), display of posters, and
incentive schemes after accident-free periods where appropriate.
2.3 Responsibilities
The Contractor is responsible, through his organization, for applying the HSE measures
required to carry out the work assigned to him by the Company so as to prevent
accidents/incidents or events which jeopardize the HSE of personnel and of the installation.
The Contractor is responsible for the correct selection of personnel to be assigned to the
jobs.
The Contractor shall possess all the equipment needed to carry out the work (appropriate for
the work environment) as well as all the clothing, safety devices and personal and collective
protection devices required.
The Contractor shall plan all actions, controls and inspections aimed at ensuring that HSE
requirements are observed, applying the measures defined in his own HSE Manual.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 4 of 24
The Contractor shall provide a fully qualified Doctor/ Medic and HSE officer appropriate at
the site.
2.4 Contractor’s HSE Organization
During the bidding stage the Contractor shall present a complete and detailed organization
chart in the form of a block diagram, which will indicate all the positions and functions
including any external organizations (Sub vender / sub contractors) involved in carrying out
the various activities covered by the Contract. It should also include the connections existing
between the contractor’s site organization and the head office.
Contractor will also submit CV’s & job descriptions of its personnel responsible for handling
HSE matters i.e. Project Manager, HSE Officer and Doctor/Medic.
Once the contract has been assigned the Contractor shall provide the Company with the
actual project organization chart, specifying also the names and relevant professional
profiles of the key positions.
Contractor shall establish and document, during the bidding stage, how the responsibilities,
competencies and authority levels are allocated to the various units or departments while the
project work is being carried out.
2.5 Responsibility for HSE Compliance
Contractor and its sub Contractors will affirm that all supervisors are responsible for ensuring
that the work is performed in accordance with all applicable health, safety and environmental
rules, regulations and good working practices, with equal diligence being paid to the
fulfillment of the contractual technical specifications.
Contractor and sub Contractors will advise such personnel of their HSE responsibilities.
Contractor shall provide Crew Organization Charts, specifying the areas of HSE
responsibility of each supervisor.
3. PERSONNEL
These requirements pertain to all Contractor personnel deployed Well Locations and access
road construction works in TAL Block.
3.1 Recruitment
The personnel & supervisors provided by the Contractor will meet the following
requirements:
a) Age Limit
The maximum allowable age limit is 60 years and make sure that any individual less than 18
years will not be hired as an employee.
b) Medical Screening
The Contractor shall ensure that all its employees are medically fit and healthy. The
contractor will arrange medical examination for its entire staff for Construction services to
MOL Pakistan at Contractor’s own cost. The Certificates of Medical fitness must be kept at
Contractor’s Camp Clinic with test reports.
Field Doctor/Medic will conduct physical examination of daily wages local labors not residing
in camps
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 5 of 24
c) Drivers / Operators
Contractor drivers/operators shall be in possession of valid driving licenses for the
appropriate category of vehicle/equipment. No unauthorized usage of transport shall be
tolerated.
Minimum requirements for driver / operators qualification, experience, selection and training
are to be certified by a third party as fully trained and competent to drive a particular vehicle
in that terrain.
3.2 CONTRACTOR’s SITE HSE Representative
Contractor will provide HSE Officer to be present at site full time. The primary responsibility
of the HSE Officer shall include, but not be limited to, the maintenance, monitoring, and
implementation of health, safety and environmental guidelines and procedures on the work
site. Co-ordination of such activities shall be conducted with and approved by Contractor’s
line management. Contractor will ensure that the HSE Officer have attended a HSE course
relevant to specific Operations.
3.3 TRAINING & AWARENESS
Contractor is responsible for maintaining and enhancing the HSE awareness of all personnel
including arranging regular toolbox talks, short training courses and emergency drills. It also
includes job related training required by law, Company regulations and Contractor’s own
HSE policy, and will provide certificates if so required. Where possible Contractor should
provide in consultation with MOL Pakistan training opportunities to suitable locals in semi-
skilled and skilled trades
Contractor shall ensure that all its personnel who require it shall have access to, and receive
adequate training and refresher courses viz.
a) HSE Induction
Contractor shall ensure that all new arrivals to the work site receives a comprehensive HSE
Induction briefing immediately upon arrival at the work site and before these new arrivals
commence work and maintain its record.
The induction should cover the emergency response and evacuation, escape routes and
mustering, communication methods, medical and first aid facilities, traveling, lifting and
rigging, environment, and other HSE aspects etc.
b) First Aid
At each work site, contractor will ensure that at least one person for each 25 people
(Minimum No. 1) has received training on First Aid and Casualty Handling, and is in
possession of a valid certificate from a recognized institute. First aid box should be available
at each vehicle and work site.
c) Fire Fighting
At each work site, contractor will ensure that at least one person for each 25 people
(Minimum No. 1) have received training on Basic Fire Fighting. Fire extinguisher should be
available at each vehicle and work site.
d) Defensive Driving Training
Contractor will ensure that all of its drivers/operators undergo a formal course on Defensive
Driving by a Third Party for Certification of drivers/operators competency prior to mobilization
at its own cost.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 6 of 24
e) Survival Techniques
At least one supervisor of each construction team shall have received hilly area search and
survival training or have demonstrated competence based on experience to a level enabling
them to carry out search operations or survive in the conditions appropriate to the area of
operations.
4.0 HSE WORKSHOP, AWARENESS AND TRAINING
4.1 PRE-MOBILISATION HSE WORKSHOP
Contractor and its sub Contractors would be required to participate in a Pre-mobilization HSE
Workshop prior to start of the work, in which event contractor should prepare notes for this
meeting covering (but not limited to) the following points.
Compliance with Environmental Management Plan (EMP)
Management of health in extreme weathers and other local health hazards.
Heat Management
Snake bite Management
Climatic and seasonal considerations (earth slips, road erosion, rains, etc.)
Technical and HSE training program (Before & during Contract) including first aid, fire
fighting, and survival techniques.
PPE Requirements.
Qualified medical services.
Contingency planning.
HSE Procedures including Emergency Handling
Auditing and reporting
Minutes of this meeting with agreed action items will be given to all participants and action
parties.
4.2 Awareness and Meetings
Contractor is responsible for maintaining and enhancing the HSE awareness of all
personnel, on the work sites including arranging regular toolbox talks, short training courses
and emergency drills.
Contractor shall be responsible for holding HSE meetings on a regular basis, to be pre-
determined in pre-mobilization workshop with company, contractor, sub Contractors and 3rd
party key and management personnel.
Copies of minutes of Contractor’s HSE meetings shall be regularly sent to Company’s HSE
Manager.
HSE meetings will also address environmental issues and, environmental induction briefings
will also be given to new starters..
Contractor shall be responsible to deliver the specific talks to its workforce involved in
hazardous operations.
5. PROJECT HSE PLAN
Contractor will prepare and submit a HSE plan at the contract award stage. At the bidding
stage, the contractor will need to submit a letter of intent that HSE Plan meeting the following
requirements will be developed at award stage, shared with the Company and implemented
during the execution stage. The plan will include the following sections:
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 7 of 24
5.1 Introduction
This section should include:
An outline of the project HSE Plan
Reference standards, Statutory Compliance and other documents
Project Management description, organization and resources
Project HSE Plan review cycle and responsibilities
5.2 Description of Facilities and Operations
This section should contain a description of the project and its components, machinery,
fittings, systems and equipment including types, numbers and location of all safety
equipment. It should specifically describe the essential features relevant to the HSE and
emergency management of the facility and operations. This enables an understanding of
how major hazards and effects, could impact the construction operations and its HSE
management systems.
5.3 Description of the Operational HSE Management System
The structure is given below with of main topics.
Leadership and Commitment
Policy and Strategic Objectives
Organization, Resources and Documentation
Evaluation and Risk Management:
Planning and Procedures
Implementation and Monitoring
Auditing and Reviewing
5.4 Hazard Register
This section should include potentially significant hazards identified for the construction
operation or site. It should demonstrate that all potentially significant hazards and effects
have been identified, the risks from the hazards and effects evaluated and understood, and
that controls to manage risks of the hazards and effects are in place. Each potentially
significant hazard identified should be described by a Hazard Sheet, which should cover the
following items:
(a) Hazard Description
(b) Possible consequences of hazards release (unmanaged or uncontrolled hazard)
What could happen?
What are possible end results?
(c) Risk Assessment based on the potential consequences of the hazard release and the
probability of this potential consequence materializing, if no special control measures
are put in place.
(d) Threats that could release the hazard.
Examples are poor weather (resulting in bad visibility, floods, and slippery roads), corrosion
(resulting in leakage of fuel containers), high gradient roads in hilly area (result in serious
accident etc).
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 8 of 24
(e) Measures to control such threats (barriers)
Barriers include physical guards, separation, procedures, etc.
(f) Escalation factors that may increase the probability or consequences of hazard
release.
Examples are worn tires (aggravating the situation in case of poor weather), impact on fuel
store (aggravating the situation in case of corrosion), etc.
(g) Control measures for escalation factors.
(h) Residual Risk Assessment based on the potential consequences of the hazard
release and the probability of this potential consequence materializing, after all
control measures are put in place.
(i) Measures to recover from the release of a hazard.
(j) Assessment of effectiveness/importance of threat control and recovery measures
such an assessment would allow a judgment whether a (high) risk is adequately
controlled. It would also allow control tasks to be ranked in order of priority and
importance.
(k) Cross reference of the controls and recovery measures to procedures, job
descriptions and other documentation used to implement the HSE-MS in the
construction operations, including PPE specifications.
Some potential hazards that can encounter during the construction activities are:
Heat stress
Snakebites/ Scorpions
Dehydration
Driving in hilly / prohibited Areas
Lack of communication
5.5 Monitoring & Remedial Plan
This section should include:
Action tracking and close-out: should describe the system used to track action items
generated from hazard analysis, job safety analysis, audits, inspections, incident
investigations and other sources.
5.6 Statement of Fitness
This section gives a statement of fitness with regard to the management system being in
place, confirmation that the hazards have been recognized and the risks to persons and
environment as a result of those hazards has been suitably reduced to as low as is
reasonably practicable.
A senior member of the Contractor’s staff who holds line management responsibility
(Project / Construction Manager or equivalent) will sign it.
6. LEGAL AND OTHER REQUIREMENTS
Contractor shall provide suitable evidence that a management system conforming to the
Company’s Health, Safety, Environment Protection policies is applied and shall comply with
the �E&P Forum guidelines pertaining to Health, Safety, and Environment. The Contractor
shall also comply with all HSE and Industrial Hygiene provisions enacted by National
Legislation.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 9 of 24
The contractor is required to comply with all relevant National, Provincial and local Laws.
6.1 Reference Laws & Provisions
a) Environmental protection laws
Pakistan Environmental Protection Act, 1997
Pakistan Petroleum (Exploration and Production) Rules, 1986
The Wild Birds and Animals Protection Act, 1992
Forest Act, 1927
Pakistan Penal Code, 1860
Canal and Drainage Act, 1873
Occupational safety laws
The Mines Act, 1923
The Regulation of Mines and Oilfields and Mineral Development (Government Control)
Act 1948, Pakistan Petroleum (production) Rules, 1949 and Pakistan Petroleum
(Exploration and Production) Rules, 1986
The Explosives Act (1884), the Explosive Substance Act (1908) and the Explosive
Rules (1940)
b) Environmental guidelines
The Guidelines for Operating Safety, Health and Environmental Management in Pakistan
Petroleum Exploration and Production Sector, 1996
FEPA prepared comprehensive Sectoral Guidelines for Environmental Reports in 1997.
Environmental Impact Assessment Guidelines
6.2 Termination & Suspension
Any infringements by Contractor’s manpower identified by Company of its HSE regulations
and standards shall be investigated jointly by Company and Contractor and remedial action
mutually agreed upon and implemented by the Contractor.
If Contractor does not implement remedial action within agreed terms, Company has the
right to stop the contract forthwith.
6.3 Alcohol & Narcotics
Contractor manpower is required to comply with Company’s Drug and Alcohol program.
Based on that program it shall be ensured that personnel do not, at any time, while traveling
to or from, or at the work, have in their possession or under influence of any contraband or
alcoholic liquor, drug or other intoxicating substances.
Company reserves a right to subject all personnel deployed in the services of the Company
to drug test at anytime without prior notice.
6.4 Weapons, Arms & Ammunition
All firearms, ammunition, knives or any other type of weapon is completely prohibited on all
MOL Pakistan Premises. This also applies to the Contractors when they are on Company’s
Concession Area or have been developed for working under MOL contracts.
6.5 Pets
Contractor and sub Contractor personnel are not allowed to keep pets or other animals in
their camps and on their work sites
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 10 of 24
6.6 Staff Rota System
All personnel will comply with Local mines act, 1923 and Rota System should be adopted for
entire staff. The schedule must be discussed and agreed by the Company in advance at the
contract pre-award Meeting. Contractor will send 15 days leave with pay to his employees
after continuous 45 day of working and is the bare minimum applicable to all categories of
personnel. However, contractor can develop the rotational cycles of his employees by using
the same ratio of working and off day.
7. PERSONAL PROTECTIVE EQUIPMENT
Contractor will responsible to ensure that all personnel at work site wear proper Personal
Protective Equipment (PPE) relevant to their nature of job. This requires:
Assessment of the type and quantity of PPE required
Issuance of required PPE to all staff
Storage of sufficient quantity of PPE at site
Continues on-site monitoring to ensure effectiveness of PPE program
Contractor shall ensure that all personnel and visitors shall wear such equipment in the
appropriate circumstances, even if not actively engaged upon the work, as the example set
by this is of paramount importance. The minimum general PPE requirement for field
operations is as follows:
7.1 CLOSE DRESS/COVERALLS AND PROTECTIVE CLOTHINGS
On site employees shall wear close dress / overalls.
Clothing/Overall should be thin, cotton made, absorbent and light colored and should be
loose enough to allow air and blood circulation.
Clothing made from nylon or similar material should not be worn as they build up a static
charge, are highly flammable and melt with heat.
Clothing contaminated with oil, chemicals or toxic substances may be a fire hazard or lead to
skin disease and should be laundered or disposed off.
7.2 SAFETY HELMETS
Safety helmets should conform to an internationally acceptable standard or code.
All personnel shall wear safety helmets at work location
Chinstraps must be fitted and used when working in exposed positions and in high winds.
7.3 SAFETY BOOTS
Safety boots should conform to an appropriate and internationally acceptable standard.
Safety boots with a covered steel toe-cap and non-skid soles shall be worn.
Note: Safety shoes and torch should be provided to all night watchmen to avoid occurrence
of snake bite, should be provided with Safety
7.4 EYE PROTECTION
Appropriate eye protection shall be worn in all working situations where hazard or potential
hazard exists. In particular, such situations shall include but not be limited to:
Operations where dust, or other particulate matter is hazardous to the eyes.
Chipping, hammering, cutting, grinding Eye wash bottles to be available at working site.
7.5 EAR DEFENDERS
Ear defenders shall be worn in areas where a hazard exists from noise above 85 dB.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 11 of 24
All high noise areas should be clearly marked and Noise warning signs to be installed
7.6 RESPIRATORS
Respirators must be worn when personnel are working in an atmosphere contaminated with
harmful airborne contaminants. They must be of an approved type as follows:
Dust masks. Used to protect from nuisance dusts, which are irritants but not harmful.
Chemical cartridge respirators used to protect from dust, fumes and nuisance vapors.
They should not be used with toxic gases of vapors.
7.7 GLOVES
Gloves shall be worn appropriate to the hazard or potential hazard.
Leather or leather palmed gloves shall be worn when working with hot equipment, during
hammering and rebar work.
Gloves shall be changed if contamination of the inner surface is suspected.
7.8 SAFETY LINES, HARNESS & BELTS
A safety line and four-point safety harness shall be worn in the following Circumstances:
When working at heights over 2 meters or other places where there is a danger from falling
(except where other means of protection against falls has been provided).
In enclosed spaces where air may be contaminated or oxygen deficient or where rescue
could be difficult in the event of injury.
Where there is a risk of falling, harness must be used in conjunction with an inertia real
safety Line.
All safety belts, lifelines and inertia reels must be inspected by a qualified person and have a
test certificate from the manufacturer and maintained appropriately and should be thoroughly
examined before use for signs of wear or damage.
7.9 SKIN PROTECTION
Mineral oils should not be permitted to remain in close contact with skin for long periods.
Hands should be protected with barrier cream and thoroughly cleansed after exposure to
condensate or other mineral oils. Oil soaked coveralls and outer clothing should be removed
as soon as possible and changed.
8. OCCUPATIONAL HEALTH REQUIREMENTS
Following standards are a guideline and are to be used by the Contractor to develop its own
project specific plan and procedures:
8.1 MINIMUM HEALTH & HYGIENE STANDARDS
Contractor shall ensure that all its employees and its subcontractor's employees engaged in
providing service to the company are medically fit and healthy.
Contractor shall at no cost to Company be responsible for the medical welfare of its own and
its subcontractor's employees
Contractor shall provide medical facilities with a qualified and experienced doctor/medic and
ambulance available full time at site.
Contractor will pay special attention to the hygiene and health of its food handlers. Routine
inspection will be carried out by Doctor/Medic, Contractor HSE personnel and Company HSE
Monitoring team.
8.2 Contractor’s Doctor or Medic
a) Contractor Doctor
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 12 of 24
The Contractor’s doctor should be a qualified MBBS with at least 05 years post graduate
experience preferably in General Medicine, General Surgery and Emergency departments.
He should have sound communication skills and knowledge of all available local medical
facilities, medical evacuation procedures and computer.
He will be interviewed by Company Doctor (for approval) before mobilization to site. He will
sit in clinic at construction base camp.
b) Contractor Medic
A medic with nursing diploma & relevant hospital experience shall be provided by contractor
who will sit in Contractor’s Base Camp Clinic.
8.3 First Aid & Medical Facilities
Contractor will provide first aid medical facilities in the base camp
Care should be taken that the medicines in the clinic cover all general diseases and that
sufficient quantity is available.
The clinic needs to equip with necessary dressing and bandages material.
8.4 Ambulance
One four-wheel drive vehicle should be available for use as a properly fitted out ambulance
at site on a 24 hours basis. They should contain:
Oxygen cylinder with face mask
Stretcher
Any source of communication (VHF Radio, PTCL V-Wireless or Mobile Phone)
Emergency Light
Rotating flashing beacon lights
Portable suction machine
Emergency kit containing items mentioned above. The kit needs to be placed in the clinic
because of the controlled temperature, and will be kept in the ambulance in case of
emergency.
8.5 Heat Stress and Controls
Extremes of ambient temperature have major consequences on human body. Work in
extreme climates poses a certain number of daily problems.
The following practices and controls can be used to minimize the affect of high temperatures
on human body:
Schedule hot jobs for the cooler part of the day.
Alter rest/work regime to permit more rest time.
Provide cool (shaded) areas for rest and recovery.
Possibility of mechanization of the physical components of the job (e.g. use of mechanical
digger rather than a shovel).
Ensure adequate supply of cold water at the work place/ sites
Ensure that employees take fluids at least every hour.
If worker’s diet is insufficient in salt or an individual is susceptible to heat strain, the water
can be salted. People on salt restricted diet (e.g. high blood pressure) should consult the
doctor before taking additional salt.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 13 of 24
Any Field person, who suspects that they may be suffering from heat stress or has been
exposed to the sun for an excessive period, should report to the Field Doctor/Medic
immediately.
9. HSE REQUIREMENTS, CAMPS & WORKSHOPS
The contractor will need to establish Base Camps to house its work force, and a workshop to
maintain its equipment. All these facilities need to confirm to the Company standards for
similar facilities. This section broadly defines those minimum standards and should be used
by the bidders to prepare their bids and by the Contractor to plan these facilities.
9.1 Campsite Selection:
The Contractor will provide a proposed location of its base camp for Company approval prior
to commencing any work on it.
9.2 Camp Standards
At the time of bidding Contractor will provide a detailed layout of its proposed base camp for
Company’s approval prior to commencing any work on it. This detailed layout will include
details of messing facilities, sleeping quarters, cooking arrangement, storage areas (food,
water & supplies).
Camp will confirm to the following minimum standards:
Proper walkways should be made
The camp should be fenced (using acceptable material) with separate gates for normal and
emergency uses and should be properly guarded.
Camp Rule’s should be posted at prominent places.
Proper Safety awareness signs should be posted all around the camp area
9.3 Camp Hygiene
A dedicated camp boss should be designated to carry out daily inspections of the entire
camp for maintaining camp hygiene.
Camp area should have adequate number of waste baskets for collection of garbage.
Contractor shall ensure that potable water for the camp is certified fit for purpose by a
reputable 3rd Party.
Disinfection should be carried out on a regular basis.
Adequate number of janitorial staff should be available to provide highest possible level of
hygiene.
Regular complete fumigation to be carried out as per advisories.
9.4 Accommodations
Accommodation shall be such that it provides protection against wind, rain and extreme
temperatures.
Accommodation shall be adequately screened against insects.
A minimum sleeping space of 4 square meters per person is recommended.
When tents are used, a floor covering capable of being readily cleaned shall be provided.
In tents candle or LALTEIN shall not be used for lighting purpose. Lights to be provided
through bulbs (generator)
Provision of mosquito net to all employees living in tents to prevent from Malaria with routine
fumigation.
Proper hygiene should be maintained for each Porta cabin / tent on a daily basis
Proper illumination of living/ working area to avoid snake bites etc.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 14 of 24
Ditch should be provided around camps to prevent snakes from entering the camp.
9.5 Kitchen Area & Food Storage
Kitchen should be in a proper room or in a Porta-cabin.
A risk assessment should be performed on the cooking area prior to mobilization.
Bon Fires are strictly prohibited and Cooking is not permitted in tents.
Gas cylinders used for cooking shall be secured properly, to avoid any accident.
Proper burners shall be used for cooking with stable and correctly sized pan supports.
All food storage shall be kept in closed containers.
Cleaning detergents or other unwanted materials / chemicals shall not be kept in food store.
Fire blanket and fire extinguishers are to be provided.
Contractor to ensure food items for at least one week in stock.
9.6 Mess Area
Mess should be in a covered area.
Mess timings shall be maintained.
9.7 Chemical Storage
All cleaning / washing chemicals should be kept separate from food storage.
Material Safety Data Sheets (MSDS) of all chemicals at site should be available.
All chemicals / detergent containers shall be labeled, for their contents.
9.8 Toilet, Sanitary Facilities & Laundry
Sufficient latrine and washing facilities shall be provided and shall be hygienically
maintained.
Washable (e.g. cement) flooring is recommended.
Laundry area should be cemented to facilitate water drainage into the septic tank.
All laundry equipment (washing machine, etc.) should be properly earthed.
Personal Protective Equipment (PPE) like apron & gloves should be worn, while handling
laundry chemicals.
9.9 Electrical System
Power generation and distribution needs to be handled with utmost care. The following
minimum standards will apply to all electrical systems operated by the Contractor during the
execution of the Contract:
All generators should be placed on a concrete pad with proper bunding arrangements.
All generators should be properly earthed as per internationally acceptable procedures.
A qualified and competent person should maintain and operate Generators.
Generator area should be out of bounds, for all personnel, except for the operator.
All electrical wires should be in PVC conduits when they are exposed to high physical wear
or high ambient temperatures.
Splicing is not allowed in the camp electrical wiring, connections must be through a junction
box.
All Junction Boxes should be weather resistant and possess proper sealing arrangements.
Earth leakage circuit breakers must be installed in each distribution board.
A separate earth wire will be used to earth all metallic enclosures.
Wiring in wet areas (shower and washrooms) shall comply with standards for such areas.
All generators, Distribution Boxes, main switches and distribution network will have to be
certified by 3rd Party, as certified fit for purpose and conforming acceptable international
standards.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 15 of 24
9.10 Fuel / Oil Storage
Following are the minimum standards that the Contractor will use to store and handle fuel at
its location.
a) Diesel
Diesel storage tanks are to be free from any leaks.
Signs for No Smoking are to be marked.
Foam type Fire Extinguishers to be placed in sufficient quantity for fire coverage.
Diesel storage areas are to be cemented and having dike walls. Storage area should have a
capacity of 1.5 times of Diesel storage.
Leak test shall be performed for the secondary containment to ensure no seepage.
Spill containment trays are to be kept for catching drips and minor spills.
b) Petrol
Following requirements should be met for Petrol storage:
Petrol should be stored in standard Jerry-cans having air vents.
Petrol should always be stored in a shade, away from the diesel storage.
Any transfer of petrol must be completed over a drip tray.
c) Oil
Lubricants to be stored in a bunded area.
Any transfer of lube oil must be completed over a drip tray.
9.11 Fire Fighting & Emergency Equipment
Contractor shall provide adequate first aid equipment, fire extinguishers and other safety
equipment to handle emergencies. These items should conform to the following minimum
company standards:
The equipment is to be maintained in a professional manner as dictated by legal and industry
standards.
An up-to-date record of manufacture, testing and maintenance of all equipment is to be
maintained.
Locations of such equipment must be clearly marked and they should be readily accessible
to all persons.
Color codes / visible marking should be used to identify different types of fire extinguishers.
All persons shall have the basic knowledge of how to operate the equipment, and the
procedures to be followed in the event of fire.
A suitable Muster point should be designated.
Manual (or electrically operated) Emergency Alarm should be installed.
9.12 Vehicle Maintenance Area
Vehicle maintenance is to be carried out at a designated area.
This area should be cemented and bunded.
Provide drip trays in case the nature of job is for a very limited time frame.
No open oil drainage should be done in or outside the camp.
Used oil should be collected in drums and disposed off through approved venders.
Used oil filters and other maintenance waste shall be segregated and disposed through
approved venders
9.13 Septic Tank
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 16 of 24
Site septic tank should be at least 20 meters from the living accommodation and build
according to standard engineering practices.
Septic tank and soak-away pit should be covered and provided with proper vents.
9.14 Waste Disposal
Adequate number of waste bins to be provided. Domestic effluent to be disposed off
properly.
Waste to be segregated properly in respective drums i.e. glass, wood, metal, plastic etc. and
disposed off properly.
9.15 Burn Pit
Camp waste to be segregated into solid waste and leftover food.
Plastic packaging and polythene bags should be segregated from the solid waste and rest of
the solid waste should be burned in a burn pit.
Contractor will prepare a burn pit to meet all safety and legal requirements.
10. ENVIRONMENTAL REQUIREMENTS
The main sensitivities are vegetation and Community so special care needs to be taken in
handling the environmental matters in the area.
This section will outline the minimum guidelines and some introduction to the way we
manage our environment and expect the contractors to follow the same.
10.1 LEGAL REQUIREMENTS AND REGULATIONS
Pakistan Environmental Protection Act 1997 (PEPA 1997) is major environmental regulations
in Pakistan. It is the responsibility of the Contractor to fully understand the
Act and implement it during its project / service period with the Company.
An important provision of the PEPA 1997 is the National Environmental Quality Standards
(NEQS) which set the limits of wastewater, air emissions and noise/vehicular emissions.
Contractors are required to comply all such limits.
10.2 ENVIRONMENTAL GUIDELINES
Contractor shall pay consideration to the environment by acting to preserve air, water, and
flora and fauna from the contrary effects of the construction activities and to minimize any
nuisance, which may arise from the operations. The following guidelines shall be applied for
the environmental protection:
Company advises the Contractor to use scrapers or bulldozers only in strictly necessary
cases only with Company’s authorization. Damages due to nonobservance of the above will
be borne entirely by the Contractor.
Contractor shall report any oil spillage to the Company and carry out remediation/reclamation
of the contaminated soil.
Contractor, in conducting the work, shall best endeavor to prevent or limit pollution within the
levels permitted by applicable laws.
Contractor shall take necessary actions to protect and respect the environment over the
Construction Area.
Affiliates harmless from and against any loss or liability (including legal expenses) arising out
of any claim or cause of action for damage to the environment.
Contractor shall follow the Environmental Management Plan in full spirit to avoid any damage
to the environment
Contractor shall not use water from ponds in the river bed/ hill streams/ /surrounding area.
Contactor shall not leave any thing in the river bed area/ hill streams area.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 17 of 24
No pollutants such as waste, oil, fuel, debris, or chemicals and the like shall be discharged or
allowed to escape to river/ hill stream.
Contractor shall be responsible for cleaning up and removing from the construction area all
the waste material and equipment, such as plastic waste, electrical wire, scraps, wrecks and
any surplus pipes as resulting from the conduct of the work.
Such clearing and clean up operations shall be conducted in accordance with the
instructions of Company or as dictated by Government. Until such removal, burial or
destruction, as permitted by applicable laws, has been effected, Contractor shall take out the
polluted or dangerous area with markers and undertake such other action to ensure safety
as may be required by the competent authorities or by Company.
Contractor shall be responsible for any bodily injury or damage to animals or material
property as suffered by Company and/or third parties and as resulting from Contractor’s
failure to carry out the aforesaid measures. All such actions shall be at Contractor’fs sole
cost and expense.
A restoration plan will be developed and provided by the Contractor, agreed by the Company
and executed prior to leaving the site.
The Contractor will be responsible for maintaining good housekeeping including the control
and disposal of domestic and general waste, hazardous materials and all other effluents and
emissions in accordance with the Company requirements.
All waste quantities shall be submitted to the Company on prescribed format on monthly
basis.
Proper planning will be carried out before any operations to ensure the highest standards of
environmental protection and restoration where appropriate. Vegetation cutting and removal
will be strictly minimized with no unnecessary cutting of trees, bushes or plants.
No material structures or other shall remain at the camp and work sites, unless specifically
requested or agreed by Company and it is the responsibility of Contractor to perform and
record the clearance of all camp and work sites.
All precautions will be taken to prevent soil and water contamination through the adoption of
approved storage methods. This will include but not limited to building secondary
containment (Bunding) of all Fuel storage areas e.g. diesel tanks with a capacity of 1.5 times
of the storage capacity by volume, drip trays for fuel transfer and lubricating oil area.
Appropriate procedures and facilities to prevent spillage of fuels and lubricants will be
adopted. Any significant spillage, incident etc., will be recorded by the Contractor and will be
reported to Company.
Local customs, cultural and religious requirements must and will be respected.
Contractor shall set out its policy and procedures for the base camp area. The site for base
camp will be identified by Contractor and approved by the Company. The Contractor will
ensure that there shall be no cutting or pruning of trees in the area without prior approval of
the Company.
All environmental incidents and accidents shall be reported as per Company procedure on
Company format.
11. JOURNEY MANAGEMENT & DRIVING
11.1 Journey Management System
The contractor is required to establish and maintain a Journey Management System to
ensure safe travel of all personnel and equipment. The components of the journey
management system should be:
Travel Management Policy
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 18 of 24
Organization and Responsibilities
Planning
Risk Assessment
Driver Standards
Vehicle standards
Implementation
Monitoring
a) Travel Management Policy
The travel management policy would define the contractor’s commitment to safe travel and
ways and means to achieve this objective.
The Travel Management Policy has the objective of:
Reducing the number of travel-related accidents
Minimizing the amount of risk exposure from traveling
Specifying the organization for travel management
Establishing criteria for the selection and use of different modes of transport
Establishing criteria for persons in charge of different modes of transport
Establishing safe working procedures for traveling
The contractor will prepare a detailed journey management system after award of contract
for approval by company. The system will conform to all current company procedures.
b) Organization & Responsibilities
Include an Organization chart showing relationships of those with responsibilities for specific
aspects of travel management.
Outline responsibilities of posts shown on the organization chart.
c) Planning
Plan the journey properly
d) Risk Assessment
Include drivers, vehicles, passengers, loads, environment, maintenance personnel, and
maintenance facilities and identify controls to be put in place for safe travel.
e) Driver / Operator Standard
All drivers / operators shall be in possession of valid driving licenses for the appropriate
category of vehicle. No unauthorized usage of transport shall be tolerated
All the drivers / operators to be certified by a third party at contractors own cost, as fully
trained and competent to drive a particular vehicle in that terrain.
As a minimum all drivers should a valid heavy-duty commercial license with five years
experience of working in remote field locations and difficult train, especially hilly areas.
All drivers should be medically screened.
Hearing and eyesight examination should be carried out and records maintained.
Contractor will ensure that all its drivers / operators undergo a formal course on defensive
driving (specially tailored for hilly areas) prior to mobilization at its own cost.
An important factor in vehicle incidents is driver fatigue. Work schedules should be arranged
so that drivers do not exceed specified daily and weekly periods of duty, which include both
driving and other work related activities.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 19 of 24
f) Vehicle Standard
Contractors will manage and maintain its vehicle fleet to the following minimum standards:
All vehicles are to be in good working condition and mechanically sound for use in that
terrain. Contractor will arrange an inspection and fitness Certificate by third party prior to
mobilization of all vehicles at his own cost. Contractor shall renew certification of each
vehicle before expiry date. The vehicle without valid certification shall not be allowed to be
use at any location of Company.
In case of any accident/ damage to the vehicle it will be re-examined by third party at
contractor’s own cost, and be generated the fitness Certificate.
All site supervisors should ensure that all forms of vehicle are correctly fitted with the
appropriate safety equipment.
A comprehensive inspection is to be performed on each vehicle before going to work site
and records maintained.
Vehicles should be thoroughly checked for any Oil strains and leaks.
Audio-visual warning devices for reversing will help avoid third party crush incidents.
Vehicle cleanliness both in the cab and outside are an important part of vehicle safety.
All seating should be securely fixed; passengers should be seated whilst traveling.
Seat belts should be of the lap/sash configuration incorporating automatic retraction and
deceleration activated emergency locking mechanisms, often referred to as inertia reels.
The use of seat belts by all occupants of cars, vans and goods vehicles should be
mandatory.
Lap belts are acceptable for center seat passengers when there are more than two seats in a
row.
The use of Vehicles with rear cargo tray seating without protection as stated above should
be prohibited
Tyres need to be maintained at the correct operating pressure.
Drivers should be responsible for checking Tyre condition on a regular basis, and reporting
any deficiencies.
Daily and weekly inspections of the vehicle on the basis of checklists (Tyres, fluids, brakes,
steering, batteries, lights etc.);
Vehicles should not be overloaded.
Ensuring that servicing and maintenance are carried out as scheduled.
Speed limits set for premises and road systems should be seen to be enforced by line
management.
Contractor should ensure that all its vehicles are in road worthy condition by implementing an
effective maintenance program.
Contractor will ensure the implementation of the above mentioned components of Journey
Management.
12. EQUIPMENT AND TOOLS
Contractor will obtain at its own cost Certificate for Clearance to operate equipments which
will be used during construction at MOL Pakistan work site following an inspection from third
party. These equipments include dozers, dumper, front end loader, excavator/ jack hammer,
cranes, trailers, mixer machines, road rollers, compactors, generators and lifting tools &
gears which will be used by contractor or its sub-contractors during construction of Well
locations & access roads.
Contractor shall make and maintain a record of these inspections, and shall make such
record available for examination.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 20 of 24
Contractor should develop a schedule for maintenance of these equipments and implement
it.
12.1 Scaffolding
Scaffolding should be of good quality and all connection tied securely.
Company will not allow any scaffolding pipe which is painted/ bended.
Contractor should follow standard scaffolding practices.
Scaffolding should only be carried out by scaffolders with adequate experience of such jobs.
Scaffolding should be inspected by Contractor scaffolding Inspector / HSE Officer & properly
tagged (saying it is approved for usage etc) before starting the work
12.2 Shuttering
Wooden shuttering to be used wherever possible.
In case of steel shuttering special care shall be taken while transporting, placing and
removing them as these are falling hazards and one should take extreme care while
removing them.
While installing & removing the shuttering proper access to be provided and safety harness/
belts should be worn all the times where there is potential of fall hazard.
12.3 General
All plant, tools and equipment are to be maintained in operable condition.
All users of plant, tools and equipment are being trained, experienced, and where necessary,
licensed and certified.
All rotating or moving parts of tools and equipment are adequately guarded to prevent
accidental contact by personnel.
Every power-driven machine should be provided with adequate means, immediately
accessible and readily identifiable to the operator, of stopping it quickly, and preventing it
being started again. In the case of chain saws and hand-held power tools, this shall be of an
automatic or "dead-man-switch" type.
a) Electrical Equipment
Electrical hand-held equipment shall be appropriately connected to an external supply with
ELCB’s.
Contractor should ensure that all portable equipment is disconnected from the power supply
when not in use.
All flexible cables shall be of industrial grade, in good and safe working condition.
Taped joints in cables shall not be permitted and plugs will always be used in power sockets.
The cables shall be protected against mechanical damage.
b) Electric Arc Welding
Both alternating and direct current welding are acceptable. Electrode holders with a
completely insulated head shall always be used, and un-insulated cable lugs shall not be
permitted. All cables shall be in good condition without mechanical damage. Joints are not
permitted. All cables shall be kept out of water and coiled when not in use.
c) Gas Welding/ Cutting
Handling, storage and usage of gas cylinders shall be in accordance with the requirements
described below.
Hoses should be protected from kinking or tangling, being stepped upon, run over by trucks
or otherwise damaged. A flashback arrester and check valve shall be installed between the
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 21 of 24
cylinder and fuel-gas hose immediately after the pressure regulator and also on the oxygen
line.
Hoses shall be inspected frequently for leaks, wear and loose connections. Leaks shall be
repaired immediately by cutting out the defective part of the hose and inserting a tube with
two hose clamps. Taping of worn hoses is not permitted.
13. HSE REPORTING
13.1 Incident/ Accident Reporting
Contractor shall report all accidents and incidents.
Contractor is required to have an accident/ incident reporting system to address all types of
accidents and incidents as classified in their procedure.
Contractor will be required to implement corrective measures that arise from the accident
investigation.
13.2 Audits & Inspections
Company reserves the right to carry out HSE audits and inspections as necessary and
Contractor will cooperate with any such requests.
Company Representatives will carry out occupational Health, Safety & Environment
Management System Audit.
13.3 HSE REPORTS
Contractor’s Daily HSE Report
Unsafe Acts/Conditions Observed/reported
Resources Utilization e.g. Water, Fuel etc
Quantity of Water abstracted from each approved well
Incidents/Accidents with brief description
Meetings/ Trainings
Inspections and Audits
Tool Box talks with topics and crew
POB
Waste Generation
Average Daily Temperatures (Minimum and Maximum)
Contractor’s Weekly CAR (Corrective Action Register)
Report to the Company’s Site Representative with copy to site HSE Monitoring team about
the situation of any accidents, which have occurred at the work site.
Environmental Weekly report includes Waste generation data
13.4 Person On-Board (POB)
Contractor shall submit a detailed report of its Person On-board on daily basis to
Company Representative.
14. EMERGENCY RESPONSE AND MEDICAL EVACUATION
When all safeguards fail, only tried and tested contingency plans can make the difference
between situation recovery and serious loss. The Contractor would be required to have
emergency response plan, related organization and physical facilities in place at the work
site to respond to any unforeseen emergency.
The following requirement addresses the need for the planning, organization, facilities and
equipment required to deal with emergency situations.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 22 of 24
14.1 EMERGENCY RESPONSE PLAN
Emergency response plans should be developed for all likely situations and shall be based
on assessed risks. Emergency response plans shall define roles and responsibilities of
persons involved and shall address particular locations, sections and departments in detail.
The subject plan will be tested by conducting an Emergency Response exercise involving all
parties immediately after the Contractor crew mobilization is completed.
14.2 FIRE PRECAUTION & ALARMS
Contractor shall prominently publish in all relevant languages and at all areas of the working
sites, the procedures to be carried out in the event of fire. This should include the sounding
of an alarm, assembly points and calling the roll, and the importance of personnel keeping
out of danger.
Contractor will establish a program of routine muster, Fire Fighting and general emergency
response drills and progress of plan will be monitored by Company on a regular basis.
15. INFORMATION / DOCCUMENTS REQUIREMENTS
a) Bidding Stage
All bidders should provide enough information to enable the Company to objectively evaluate
their commitment to adhere to company HSE standards. The information will include but is
not limited to:
Standard Documents
Contractor’s organization chart with details of key personnel.
Contractor’s Proposed Project Organization with details of key personnel.
Contractor’s Corporate HSE Philosophy and Policy.
Contractor’s HSE Statistics for last 3 years
Contractor’s detailed Safety Manual clearly stating responsibilities
Details Contractor’s dedicated personnel who will hold sufficient authority to manage the
entire Contract and to organize the work and site
Contractor’s policy on use of PPE.
Exceptions to Quality and Technical requirements (observations, comments, proposals for
modifications to Quality and Technical requirements)
A typical example of the Quality Control Plan for the SERVICE(S) covered by the Contract
List of personnel and subcontractors to be used for camp setup and management.
List of camping equipment, generators, facilities, etc. already available with the Contractors.
Contractor’s camping plan, including the resources and methodology that it plans to use for
managing its camp.
Contractor’s Environmental Management Philosophy.
Any other additional information the Contractor deems useful in this respect.
List of medical personnel already in employment with the Contractor, including their
qualifications.
List of medical equipment, facilities, etc. already available with the Contractors.
Contractor’s current health policies and procedures
Contractor’s travel management philosophy.
List of major tools and equipments that the contractor wishes to use in the projects and
setting the camp with their location and present state of certification. Company may inspect
them or audit relevant records as part of its bid evaluation exercise.
LTIFR (Lost Time Injury Frequency) for a significant time (at least 3 years);
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 23 of 24
LTIFR target for the current year
Breakdown of statistical injury for different activity
Any other additional information the Contractor deems useful in this respect.
16. Commitments
Contractor to submit written confirmation that they will undertake company prescribed
medical examinations and screening tests for their staff at their own cost from Company’s
approved hospitals.
Letter of intent to develop the HSE Plan at contract award stage and implement at execution
stage
Commitment to submit 3rd Party fitness certificates of all Vehicles for its services at
contractor’s own cost.
Contractor should commit that all its drivers will be certified by a third party as fully trained
and competent to drive a particular vehicle in that terrain.
All bidders should commit that they will comply with HSE and Industrial hygiene provisions of
Local, Provincial & National laws.
Abide company policy regarding Alcohol & Narcotics and Weapons, Arms & Ammunition.
Commitment to comply with the requirement of IEE & NOC.
Commitment to comply Company’s procedures and rules applicable to their scope of work.
Contractor should commit that it will abide company policy regarding respecting local
traditions and culture.
Letter of intent to develop the Health Management and action plan for Snakebite
Management for Construction activity.
Contractor should submit written commitment that they will certify generators, distribution
boxes, main switches and distribution network by 3rd Party.
a) Requirements on Contract Award
Contractor will be expected to prepare all agreed Procedures before initiating any physical
activity.
Contractor will submit the copies of Medical Fitness Certificates of its employees.
Contractor’s HSE Plan
Adequate experience / trainings evidences of site supervisors, operators and drivers
Contractor’s Vehicles Fitness Certifications by 3rd party.
Contractor’s philosophy and approach towards Corporate Social responsibility.
Contractor will be expected to prepare a comprehensive Travel Management Plan and
Procedures in consultation with the Company.
List of documents for the job (Minutes of Meeting, Quality Documents, any documents
specifically written for the Contract;
Contractor’s Health management plan for the construction activity with special reference to
the possibility of insect/reptile bites.
Procedure for recordkeeping and disaster management should also be prepared.
Contractor will be expected to prepare its Emergency Response Procedure specific to
TAL Block area and provide evidence that is making arrangements to put its emergency
response organization in place prior to mobilization and ensure that all necessary facilities
and equipment to handle emergency are available at site prior starting the activity.
b) Requirements during Execution of Work
Contractor shall report all accidents and incidents to the Company.
HSE REQUIREMENTS & GUIDELINES FOR WELL LOCATIONS & ACCESS ROADS CONSTRUCTION WORK IN TAL
BLOCK
Page 24 of 24
Contractor will be expected to implement their Health and Hygiene Procedure (approved by
the Company) and all agreed HSE requirements and Guidelines provided by Company.
Contractor shall submit a detailed report of its Person On-board on daily basis to Company
Representative.
The Contractor shall submit all daily and weekly HSE reports asked in ITT.
Weekly HSE report including Water / fuel consumption and waste generated data.
Contractor shall be responsible for holding HSE meetings on a regular basis including
environmental issues. Copies of minutes of Contractor’s HSE meetings shall be regularly
sent to Company’s HSE representative.
c) Requirements on Completion of Work
Contractor will submit Project HSE close out report including all health, safety and
environmental issues, project HSE statistics and major HSE achievements.