his operation centum vp

HIS Operation

IM 33M05D10-40E

IM 33M05D10-40E2nd Edition

iIM 33M05D10-40E

IntroductionThis operation manual is written for plant operators who use the CENTUM VP to perform operation and monitoring. This manual comprises the following chapters. Listed below are their brief explanations:

Starting up HIS This chapter explains HIS windows structure and how to start up HIS.

Calling the Graphic Views This chapter explains how to use the buttons to call the graphic views.

Useful Features of HIS This chapter explains the easy and efficient functions to use HIS.

Operating the Instrument Faceplate This chapter explains how to operate the instrument faceplate.

When a Message is Generated This chapter explains the measures that should be taken when a message is generated while operating/monitoring the plant and how to find messages generated in the past.

Reading the Data collected from Plant This chapter explains how to use the trend view to read data acquired from the plant.

Outputting Screen Images This chapter explains how to output the screen images.

When a System Error Occurred This chapter explains the measures that should be taken when a system error occurred.

2nd Edition : Dec.22,2009-00Media No. IM 33M05D10-40E (DVD) 2nd Edition : Dec. 2009 (YK)All Rights Reserved Copyright 2008, Yokogawa Electric Corporation

ii

IM 33M05D10-40E

CENTUM VP Document Map

HIS OperationIM 33M05D10-40E

EngineeringTest Guide

IM 33M10D20-40E

OperatingMessages

IM 33M05D20-40E

ReferenceIM 33M01A30-40E

APCSDocumentation

EngineeringTutorial

IM 33M10D10-40E

User's manual

Only available in electronic document

Relationship between manualsthat must be read in order

Relationship to a referred manual

Reference manual

Engineering

Operation and Monitoring

Hardware

Installation

CommunicationDevices

IM 33M50D10-40E

TurbomachineryI/O Modules

IM 33M10U10-40E

Input & OutputModules

IM 33M50G10-40E

Field ControlStations

IM 33M50E40-40E

CENTUM VP InstallationIM 33M01A20-40E

PeripheralsIM 33M50C10-40E

CENTUM VPEngineeringGuidance

FieldbusDocumentation

CENTUM Data Access Library

IM 33M05F10-40E

Migrated-FCS (FIO)IM 33M50W10-40E

Vnet/IPIM 33L01A10-40E

1st Edition : Mar.23,2008-00

iii

IM 33M05D10-40E

Safety Precautions

n Safety,Protection,andModificationoftheProduct In order to protect the system controlled by the product and the product itself and ensure

safe operation, observe the safety precautions described in this users manual. We assume no liability for safety if users fail to observe these instructions when operating the product.

If this instrument is used in a manner not specified in this users manual, the protection provided by this instrument may be impaired.

If any protection or safety circuit is required for the system controlled by the product or for the product itself, prepare it separately.

Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter simply referred to as YOKOGAWA) when replacing parts or consumables.

Modification of the product is strictly prohibited.

The following symbols are used in the product and users manual to indicate that there are precautions for safety:

Indicates that caution is required for operation. This symbol is placed on the product to refer the user to the users manual in order to protect the operator and the equipment. In the users manuals you will find precautions to avoid physical injury or death of the operator, including electrical shocks.

Identifies a protective grounding terminal. Before using the product, ground the terminal.

Identifies a functional grounding terminal. Before using the product, ground the terminal.

Indicates an AC supply.

Indicates a DC supply.

Indicates that the main switch is ON.

Indicates that the main switch is OFF.


iv

IM 33M05D10-40E

n Notes on Handling Users Manuals Please hand over the users manuals to your end users so that they can keep the users

manuals on hand for convenient reference. Please read the information thoroughly before using the product. The purpose of these users manuals is not to warrant that the product is well suited to any

particular purpose but rather to describe the functional details of the product. YOKOGAWA reserves the right to make improvements in the users manuals and product at

any time, without notice or obligation. If you have any questions, or you find mistakes or omissions in the users manuals, please

contact our sales representative or your local distributor.

n Warning and DisclaimerThe product is provided on an as is basis. YOKOGAWA shall have neither liability nor responsibility to any person or entity with respect to any direct or indirect loss or damage arising from using the product or any defect of the product that YOKOGAWA can not predict in advance.

n Notes on Software YOKOGAWA makes no warranties, either expressed or implied, with respect to the

softwares merchantability or suitability for any particular purpose, except as specified in the terms of warranty.

This product may be used on a machine only. If you need to use the product on another machine, you must purchase another product.

It is strictly prohibited to reproduce the product except for the purpose of backup. Store the DVD-ROM (the original medium) in a safe place. It is strictly prohibited to perform any reverse-engineering operation, such as reverse

compilation or reverse assembling on the product. No part of the product may be transferred, converted or sublet for use by any third party,

without prior written consent from YOKOGAWA.


vIM 33M05D10-40E

Documentation Conventions

n TypographicalConventionsThe following typographical conventions are used throughout the users manuals:

l Commonlyusedconventionsthroughoutusersmanuals:

Characterstringtobeentered:

The characters that must be entered are shown in monospace font as follows:Example:

FIC100.SV=50.0

Mark

This symbol indicates the description for an item for which you should make a setting in the products engineering window. While operating an engineering window, the help information for the selected item can be accessed from Builder Definition Items in the Help menu.

Listing more than one definition item after this symbol implies that the paragraph on the page describes more than one definition item.

Example: Tag Name, Station Name

Mark

Indicates a space between character strings that must be entered.Example:

. ALPIC010-SC

Characterstringenclosedbybrackets({}):

Indicates an option that can be omitted.Example:

. PRTAG{.sheet name}


vi

IM 33M05D10-40E

l Conventionsusedtoshowkeyorbuttonoperations:

Charactersenclosedbybrackets([]):

Characters enclosed by brackets within any description on a key or button operation, indicate either a key on the HIS (Human Interface Station) keyboard, a key on the operation keyboard, a button name on a window, or an item displayed on a window.Example:

To alter the function, press the [ESC] key.

l Conventionsusedincommandsyntaxorprogramstatements:The following conventions are used within a command syntax or program statement format:

Charactersenclosedbyangle-brackets:

Indicate character strings that user can specify freely according to certain guidelines.Example:

#define

...Mark

Indicates that the previous command or argument may be repeated.Example:

Imax (arg1, arg2, ...)

Charactersenclosedbybrackets([]):

Indicate those character strings that can be omitted.Example:

sysalarm format_string [output_value ...]

Charactersenclosedbyseparators(||):

Indicate those character strings that can be selected from more than one option.Example:

opeguide [, ...]OG,


vii

IM 33M05D10-40E

n SymbolMarksThroughout this users manual, you will find several different types of symbols are used to identify different sections of text. This section describes these icons.

CAUTION Identifies instructions that must be observed in order to avoid physical injury and electric shock or death of the operator.

WARNING Identifies instructions that must be observed in order to prevent the software or hardware from being damaged or the system from becoming faulty.

IMPORTANT Identifies important information required to understand operations or functions.

TIP Identifies additional information.

SEE ALSO

Identifies a source to be referred to.

Clicking a reference displayed in green can call up its source, while clicking a reference displayed in black cannot.

n Drawing ConventionsSome drawings may be partially emphasized, simplified, or omitted, for the convenience of description.Some screen images depicted in the users manual may have different display positions or character types (e.g., the upper / lower case). Also note that some of the images contained in this users manual are display examples.


viii

IM 33M05D10-40E 2nd Edition : Dec.22,2009-00

CopyrightandTrademarkNotices

n AllRightsReservedThe copyright of the programs and online manuals contained in the DVD-ROM or CD-ROM shall remain in Yokogawa.You are allowed to print out the required pages of the online manuals for using the product, however, you are not allowed to print out the entire document. You can purchase the printed manual from Yokogawa.Except as stated above, no part of the online manual may be reproduced, either in electronic or written form, registered, recorded, transferred, sold or distributed (in any manner including without limitation, in the forms of paper documents, electronic media, films or transmission via the network).

n TrademarkAcknowledgments CENTUM and Vnet/IP are registered trademarks of YOKOGAWA. Microsoft, Windows, Windows Vista, Visual Basic, Visual C++ and Visual Studio are either

registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Adobe, Acrobat and Acrobat Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Ethernet is a registered trademark of XEROX Corporation. Java is a registered trademark of Sun Microsystems,Inc. MELSEC is a registered trademark of Mitsubishi Electric Corporation. Modicon and Modbus are registered trademarks of Schneider Electric SA. Memocon-SC is a registered trademark of Yaskawa Electric Corporation. PLC is a registered trademark of Rockwell Automation, Inc. SYSMAC is a registered trademark of OMRON Corporation. SIEMENS and SIMATIC are registered trademarks of Siemens Industrial Automation Ltd. FOUNDATION in FOUNDATION fieldbus is a registered trademark of Fieldbus Foundation.

SmartPlant is a registered trademark of Intergraph Corporation. HART is a registered trademark of the HART Communication Foundation. All other company and product names mentioned in this users manual are trademarks or

registered trademarks of their respective companies. We do not use TM or mark to indicate those trademarks or registered trademarks in this

users manual. We do not use logos and logo marks in this manual.

Toc-1

IM 33M05D10-40E

CENTUM VPHIS Operation

2nd Edition : Dec.22,2009-00

CONTENTS

IM33M05D10-40E2ndEdition

1. StartingupHIS .......................................................................................... 1-11.1 HISOperation And Monitoring Windows .......................................................1-41.2 UsingSystemMessageBanner ......................................................................1-71.3 UsingBrowserBar ............................................................................................1-8

2. UsingGraphicViews ................................................................................ 2-12.1 CallingGraphicViews ......................................................................................2-22.2 UsingGraphicView ..........................................................................................2-4

3. Useful Features of HIS ............................................................................. 3-13.1 OperationPanelMode ......................................................................................3-23.2 SwitchingtoOperationandMonitoringWindowswhileoperating

general-purposeWindowsApplications ........................................................3-43.3 UsingShortCutKeys .......................................................................................3-53.4 Multiple-Monitor ................................................................................................3-9

4. OperatingtheInstrumentFaceplate ...................................................... 4-14.1 EnteringData .....................................................................................................4-24.2 ChangingtheBlockMode ................................................................................4-64.3 OperationMarkonInstrumentFaceplate ......................................................4-84.4 TightShutandFullOpen ...............................................................................4-10

5. WhenaMessageisGenerated ............................................................... 5-15.1 ConfirmingMessages ......................................................................................5-25.2 MessageSearch ................................................................................................5-95.3 Messages On Help Window ...........................................................................5-155.4 ConfirmingMessagesinCAMSforHIS........................................................5-18

6. ReadingtheTrendofProcessData ........................................................ 6-16.1 ConfirmingDataintheTrendView .................................................................6-26.2 ChangingtheAssignmentofTrendDataBeingDisplayed ..........................6-46.3 Creating/Displaying Trend Reference Patterns ............................................6-8

7. Outputting Screen Images ...................................................................... 7-17.1 OutputtingtheScreenImageofCurrentlyDisplayedWindows .................7-27.2 OutputtingthePreviouslyOutputScreenImagesAgain .............................7-6

8. WhenaSystemErrorOccurred .............................................................. 8-1

Blank Page

1-1

IM 33M05D10-40E

1. StartingupHISItisnecessarytostartupanHISbeforecommencingtheplantoperationandmonitoring.ThischapterexplainsthestepstostartuptheHIS.

n Starting up HIS1. Turn on the power of the computer running Windows.2. In the Windows log-on window, enter the user name and password that were set in the HIS

Utilities dialog box. HIS will start up.

TIPIf [Auto Logon] is checked in the HIS Utility dialog box, turning on the power of the computer with Windows will automatically start up the HIS.


1-2

IM 33M05D10-40E

n SecurityCheckforOperationandMonitoringonHISThe operation and monitoring scope on HIS is determined by the settings of user group and the privilege level.The user rights on the HIS are predefined on the HIS security builder according to the user group and the privilege level.The security setting of each HIS can be different from others, so that a users right maybe different on different HISs. Thus a users operation and monitoring scope on a HIS can be performed only in the range predefined for the HIS.

l ChangingPrivilegeLevelIf an operation keyboard is connected to the HIS, the privilege level can be changed by switching the MODE key on the keyboard.There are two types of keys for the keyboard, operation key and engineering key.

010001E.ai

In the case of the operation keyChanges between the ON, OFF positions.

When the engineering key is inserted.The key can beswitched to any position.

MODEOFF

ONENG

MODEOFF

ONENG

Figure ModeSwitchingKey

Using an operation key cannot switch to ENG position. When the MODE switch position is OFF or no key:

Privilege level of the user(logged-in user) during operation When the MODE switch position is ON:

S2 privilege When the MODE switch position is ENG:

S3 privilege

TIPIn the CAMS for HIS message monitor, the privilege level set by the MODE key is not applied. For example, if you log in as an S1 user, your privilege level remains S1 even if you turn the key to ENG.

SEE ALSO For more information about the security with operation keyboard, see the following:

n Change Privilege Level on Operation Keyboard in F3.3, Privilege Level of Reference (IM 33M01A30-40E)


1-3

IM 33M05D10-40E

l SwitchingUserafterHISStartupAfter HIS startup, the HIS user can be switched on User-In dialog box.1. Click the following user information display area on the toolbar of the system message

window of HIS.

010002E.aiTESTUSER

SEE ALSO For the details of System Message Banner, see the following:

1.2, Using System Message Banner

The User-In dialog box displays.

010003E.ai

User Name

Password

CancelUser OutUser InChange Password

ENGUSER

Shut Down

User-In

User Information

User ENGUSER (Default ENG User)Group DEFGRP (Default User Group ALL)Since 2004/10/28 16:52

Figure User-InDialogBox

2. Enter user name and password to this dialog box.3. Click [User-In] button.

The user is switched and the operation right is also switched accordingly.

SEE ALSO For more information about User-In dialog box, see the following:

n User-In and User-Out in E2.5.1, Components of System Message Banner of Reference (IM 33M01A30-40E)


1-4

IM 33M05D10-40E

1.1 HISOperation And Monitoring WindowsTheoperationandmonitoringwindowsofHISareexplainedinthischapterforproperlyusingthewindowsaccordingtotheoperationaltargets.

SEE ALSO For more information about various HIS windows, see the following:

E2.3, System Windows and User-Defined Windows of Reference (IM 33M01A30-40E)

The HIS Operation and Monitoring Window is composed of the following areas.

Recycle Bin

010101E.ai

Container window

Window Desktop

Frame

View

Browser bar

System Message Banner

Figure HISDesktop

System Message Banner: shows alarms and provides buttons to call views or windows on the alarms, a button to switch users, a button to print and others.

Browser bar: lists the names of views and windows, and tag information CENTUM VP provides together with buttons to call them.

Container window: the outer window of the HIS display area containing a frame.Frame: shows views immediately below per each purpose or feature

within the Container window.View: contents shown in a frame.


1-5

IM 33M05D10-40E

For facilitating your operation and monitoring

For Managing Units

For Checking Process Status and Operation Logs

Tag Report Search

I/O Report Search

Search for a Historical Message

Graphic View

Trend View

Tuning View

Trend Point View

Faceplate View

Custom Faceplate View

Operator Guide View

Process Alarm View

Message Monitor Window

SFC View

Logic Chart View

Sequence Table View

Control Drawing View

Image Window

SEBOL View

SEBOL Detail View

Help Window

Process Report View

Historical Message Report Window

Operator Guide Individual Acknowledgement

Process Alarm Individual Acknowledgement

CAMS for HIS Message Monitor View

CAMS for HIS Historical Viewer

For Managing Systems

Basics of Operation and MonitoringSystem Message BannerBrowser Bar

010102E.ai

*2

*1

*3

*2

*3

Fiugre HISOperationAndMonitoringWindows(1/2)

*1: Valid only if you use CAMS for HIS.*2: Valid only if you do not use CAMS for HIS.*3: Valid only if you do not use CAMS for HIS, or if you use CAMS for HIS and Operator Guide Message is not integrated.


1-6

IM 33M05D10-40E

Windows for System Administration

Station Tab

Printer Tab

Buzzer Tab

Display Tab

Window Switching Tab

Alarm Tab

Preset Menu Tab

Equalize Tab

Function Keys Tab

Operation Mark Tab

Multimedia Tab

Browser Bar Tab

Trend Tab

Long-Term Tab

External Recorder Tab

Report Tab

OPC Tab

Multiple-Monitor Tab

Process Management Tab

System Report Dialog Box

HIS Report Dialog Box

FCS Report Dialog Box

Gateway Status Display Dialog Box

HIS Report Dialog Box

Touch Panel Maintenance Dialog Box

V net Setup Dialog Box

Node Status Display Dialog Box

FCS Report Dialog Box LFCS

BCV Report Dialog Box

System Alarm Message Search

System Alarm Individual Acknowledgment Window

System Status Overview View

System Alarm View

HIS Setup Window

Advanced Alarm Filter Window

BCV Status Display View

HIS Status Display View

Adjust Time Dialog Box

FCU Status Display View XL

EFCS Status Display View XL

EFUS Status Display View XL

FMS Status Display View XL, V

CFCS Status Display View CENTUM V

xFCS Status Display View

010103E.ai

Basics of Operation and MonitoringSystem Message WindowNavigator Window

*2

Fiugre HISOperationAndMonitoringWindows(2/2)


1-7

IM 33M05D10-40E

1.2 UsingSystemMessageBannerSystemMessageBannershowsalarmsandprovidesbuttonstocallviewsorwindowsonthealarms.

Alsobuttonsforswitchingusersandprintingareprovided.

010201E.ai

?Copy

00 0

2008/03/03 14:35

TESTUSER

FCS0101 Batch Manager Ready FCS0101 RIGHT Control FCS0101 RIGHT Manual Reset Start

Process Alarm

System Alarm

Operation Guide

Message Display Area

Icon Display Area

Message MonitorUser InBuzzer Reset

Hard Copy

Figure SystemMessageBanner

SEE ALSO For the details of the System Message Banner, see the following:

Section E2.5, System Message Banner in Reference (IM 33M01A30-40E)


1-8

IM 33M05D10-40E

1.3 UsingBrowserBarBrowserBarliststhenamesofviews,windows,andtagsthatCENTUMVPprovides.

BrowserBaralsoprovidesbuttonstocalltheviewsandwindows.

Browser Bar contains the following boxes. Click the tabs in the left most strip to switch the boxes.

Overview Tool Box

Preset Menu Tool Box

Tool Button Tool Box

Name Input Tool Box

Window History Tool Box

010301E.ai

Overview Preset Menu

CommentAddress /USER

Favorite favorite-1 MYPJT1 .SH GR0002 favorite-2 TG0216 CG0001

OverviewView Trend Plant

NAME

Search

USER CG0001 CR0001 OV0001 TG0101 TG0201 TG0301 TG0401 TG0501 TG0601 TG0701 TG0801 GR0003SYSTEM .AL .OG .SO .PRPRODUCT

PP

?

Preset Menu

NAME

Hard Copy

CG0001

Circhlate

User In

Figure ToolBox(1/2)


1-9

IM 33M05D10-40E

010302E.ai

Tool Button Name Input

Tool Button

NAME

Name Input

NAME

Wnidou Name Input

Call

Default Stabio;Ingotmtn

Window History

NAME

Window History

Function Name

O LI201 -SCCG0001GR0002CG0001O FIC100FF -SCGR0001GR0001OV0001OV0001CG0001O FIC100FF TUN -SMFIC002FIC002System Status OverviewFIC001Station Status Display

O LI201 -SCO CG0001 -SLO GR0002 -SLO CG0001-SLO FIC100FF -SO GR0001 -SLO GR0001 -SLO OV0001 -SLO OV0001 -SLO CG0001 -SMO FIC100FF TUO FIC002 TUN O FIC002 -SCO .SO -SL O FIC001 -SCO .SF FCS0102

Command .

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Figure ToolBox(2/2)


Blank Page

2-1

IM 33M05D10-40E

2. UsingGraphicViewsThischapterdescribesbasicgraphicviewsforoperatingandmonitoringplant,andhowtousethem.

n WhatisGraphicView?Graphic View is a window showing a customized plant view with control statuses. It shows real-time process status. You can create the Graphic View from the Graphic Builder.

SEE ALSO For the details of Graphic Builder, see the following:

Section F12. Graphic Builder of Reference (IM 33M01A30-40E)

The following figure shows an example of Graphic View.

020001E.ai

Ready

DISTILGR_3D 3D Distillation Graphic

Vapor

Reflux Drum

Steam

Reboiler

BottomExtraction

1MC1011MC101

1MC300

CondenserDistillation Column

Oscill TR

Tag Display

Dist TR

ALRM

ALRM

ALRM

Feedstock

Compressor okay

Dynamic

Instruments

1LIC100

36.2 %

1FIC101

DEVICE ALERTCHECK PRM!

40.8 M3/H

1TIC100

59.4 DegC

DegC

M3/H

1FIC100

70.0 M3/H

1TIC400

48.1

1FIC300

31.7

1LIC300

25.9 %

1FIC200

36.2 M3/H

SYS-OV

1 22D

3 4

Figure GraphicView

n AttributesofGraphicViewsGraphic views are categorized into three attributes.

Graphic views with graphic attribute Become the target of call operation via the graphic button.

Graphic views with overview attribute Become the target of call operation via the overview button and graphic button.

Graphic views with control attribute Become the target of call operation via the control button.


2-2

IM 33M05D10-40E

2.1 CallingGraphicViewsYoucancallgraphicviewsbyclickingthebuttontodisplayGraphicviewintheBrowserBar,orbyenteringthegraphicviewnameintheNameInputToolBox.

n CallingfromtheBrowserBar1. In the Tool Button Tool Box in the Browser Bar, click the button to display Graphic view. 2. Graphic view opens. (Graphic attributes)*1

020101E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Graphic view

Figure OpeningGraphicView

*1: when you first open the Graphic view, the graphic view at the top of the hierarchy appears. From the second on, the previously called graphic view appears.


2-3

IM 33M05D10-40E

n CallingfromtheNameInputToolBox1. In the Name Input Tool Box in the Browser Bar, enter the name of the graphic view you

want.

020102E.ai

Name Input

NAME

Window Name Input

Call

Default Station Information

GRAPHIC 1

Figure EnteringinNameInputToolBox

2. Press the Call button. The graphic view you requested (GRAPHIC 1 in the above example) appears.

SEE ALSO For calling other windows from the Name Input Tool Box, see the following:

The section l Calling up Windows by Entering Names in the section E2.7.1, Directly Calling up Operation and Monitoring Windows in Reference (IM 33M01A30-40E)


2-4

IM 33M05D10-40E

2.2 UsingGraphicViewThissectiondescribesthebasicsofhowtousegraphicview.

n ChangingFaceplateAssignmentThe faceplates displayed on the graphic windows can be assigned to different function blocks. The new assignment will become valid only after the changed contents are downloaded to HIS.The detailed procedure is as follows:

1. Click the button to display Faceplate Assignment dialog.

020201E.ai

The Faceplate Assignment dialog box displays as follows.

CancelOK

020202E.ai

1. FIC100

FI101

FI102

FI103

FI104

TIC100

TIC200

TIC300

2.

3.

4.

5.

6.

7.

8.

9. AIC100

LIC10010.

11.

12.

13.

14.

15.

16.

Faceplate Assignment

Figure FaceplateAssignmentDialogBox

2. Enter a new tag names to the corresponding faceplates, then click [OK] button. The faceplates will indicate the newly changed function blocks.


2-5

IM 33M05D10-40E

n SwitchingGenericNameSetofGraphicDisplaysWhen creating Graphic views for similar process units, if their drawing objects are the same but the function block, data item of process data, modifier conditions as well as constant values indicated by the drawing objects are different, thus using Generic Name Set switching the bound data can display the multiple units with one graphic view.How to switch the data bindings using the predefined data set are explained as follows.

SEE ALSO For more information about generic name set of graphics, see the following:

F12. Graphic Builder of Reference (IM 33M01A30-40E)

1. Call an operation and monitoring graphic view.2. Click the button to display Switch Generic Name Set dialog on the graphic view.

020203E.ai

Switch Generic Name Set dialog box displays.

020204E.ai

CancelOK

Switch Generic Name Set

BIND01Set Name

Comment

Generic name set

Comment

Figure SwitchGenericNameSetDialogBox

3. Choose a generic name set from the pull-down list, and then click [OK]. The data displayed on the graphic view will be changed to a different data set.


2-6

IM 33M05D10-40E

n ZoomInandZoomOutofGraphicViewUsing the Zoom In/Out setting box, the graphic views zoom levels and the center of the zoomed window can be set.Besides the graphic windows, this tool can also be used for zooming Logic Chart view and Control Drawing view.How to zoom in or zoom out a graphic window is explained as follows.

1. Call an operation and monitoring graphic view.2. Click the button to display Pan & Zoom dialog on the graphic view.

020205E.ai

Pan & Zoom dialog box displays.

020206E.ai

Pan & Zoom

+

-

Figure Pan&ZoomDialogBox

Zoom InTo zoom in, do one of the following. Click [ZoomIn] button ( button). Move the slider in the direction [ZoomIn].

Zoom OutTo zoom out, do one of the following. Click [ZoomOut] button ( button). Move the slider in the direction [ZoomOut].


3-1

IM 33M05D10-40E

3. Useful Features of HISInordertoimproveoperability,thefollowingfunctionsarepreparedinHIS.

Thischapterexplainsthesefunctionsandsetupforusingthese.

Usingthetwooperationpanelmodes

SwitchingtoOperationandMonitoringWindowswhileoperatinggeneral-purposeWindows Applications.

UsingtheShortcutKeys

UsingtheMultimonitoring


3-2

IM 33M05D10-40E

3.1 Operation Panel ModeTwooperationpanelmodes,full-screenmodeandwindowmodeareavailable.Theoperatorcanswitchfromonemodetotheotheraccordingly.

SEE ALSO For more information about operation panel mode, see the following:

E2.2, Operation Screen Mode of Reference (IM 33M01A30-40E)

n SwitchingtheOperationPanelModeSwitching between the full-screen mode and window mode is done in the HIS Setup window.

IMPORTANT The selected operation panel mode will become effective after logoff.

1. In the Tool Button Tool Box in the Browser Bar, click the button to show System Status Overview view.

030101E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

OverviewSystem Status Overview View

Figure Opening System Status Overview View

2. System Status Overview view appears. In the view, click the button for HIS Setup.

030102E.ai


3-3

IM 33M05D10-40E

The HIS Setup Window displays as follows.

030103E.ai

.SH HIS Setup

Font Name

Courier New (Westem)

Height

Font

16

Reset to Defaults

5

2

3

HelpApplyCancelOK

24x24

Window Design

Tag Name Length 12

Windows Type

Change Reconfirmation Button Style

Use Tooltips for Data Items

Toolbar Button Size

Default (Double Click)Pointing Operation

Operation Screen Mode (HIS should be reastan.)

Full Screen Mode

Number of pop-Up Windows

Number of Fiamge

Window Mode

Number of Containneee

Use faceplate frame as a default

File

Control Drawing

Logic Chart

Status Display without Scaling

REPORT Process Management Multiple-MonitorEqualize Function Keys Operation Mark Multimedia Long-Term

OPCWindow Switching Navigator Alarm

Preset Menu

Station Printer Buzzer Display

(When two or more monitors are used, the following value is needed for each monitor.)

Figure DisplaytaboftheHISSetupWindow

3. Open [Display] tab.4. Check [Full Screen Mode] in the field of Operation Screen Mode, and then click [OK] button.

5. Restart HIS.


3-4

IM 33M05D10-40E

3.2 SwitchingtoOperationandMonitoringWindowswhileoperatinggeneral-purposeWindows Applications

Tomovetheoperationandmonitoringwindowstotheforefrontofthescreenwhileyouareusingageneral-purposeWindowsapplication,usetheCirculatefunction.Withthisfunction,youcanmovetheHISwindowstogethertothefrontortotheback.

n Using Circulate function1. While you are using a general Windows application, click the button to circulate in the Tool

Button Tool Box.

030201E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Circulate

Figure Executing Circulate

2. The Operation and Monitoring Window at the back is moved to the front.

System Message Banner System Message Banner

030202E.ai

Bro

wse

r Bar

Bro

wse

r Bar

WindowsApplication Window

Operation and Monitoring Window

WindowsApplication Window

Operation and Monitoring Window

Figure Circulate


3-5

IM 33M05D10-40E

3.3 Using ShortCutKeysUsingtheshort-cutkeysprovidedbyHIS,youcanexecutefunctionsassignedtotheFunctionkeysontheOperationkeyboard.

ItwillenableyoutooperateHISefficientlyfromthekeyboardonstandardPCsinanenvironmentwherenoOperationkeyboardisavailable.

SEE ALSO For details of short cut keys, see the following:

Section E2.12, Shortcut Keys for Operation and Monitoring Windows in Reference (IM 33M01A30-40E)

n Preparingforusingshort-cutkeysBefore you use the short-cut keys, you must do the following. 1. Assign functions to the Function keys on the Operation keyboard. 2. Enable short-cut keys.

l AssigningfunctionstotheFunctionkeysontheOperationkeyboardYou can assign functions to the Function keys on the Operation keyboard in the Function Key Assignment Builder or HIS Setup window.

SEE ALSO For details of function keys, see the following:

Section E13.2, Function Keys in Reference (IM 33M01A30-40E)


3-6

IM 33M05D10-40E

l Enablingshort-cutkeys1. Click the Tool Button Tool Box tab in the Browser bar, and then click the button to show the

System Status Overview view.

030301E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

OverviewSystem Status Overview view

Figure OpeningtheSystemStatusOverviewView

2. The System Status Overview view appears. Click [HIS Setup]. HIS Setup window opens.

030302E.ai


3-7

IM 33M05D10-40E 1st Edition : Mar.23,2008-00

3. Click the Station Tab, and then select the [Emulate Function Key] check box. Click [OK].

030303E.ai

.SH HIS Setup

File

REPORT Process Management Multiple-MonitorEqualize Function Keys Operation Mark Multimedia Long-Term

OPCWindow Switching Navigator Alarm

Preset Menu

Station Printer Buzzer Display

Cancel ApplyOK

ExportImport

Help

Print

(The computer should be restarted.)

Number of Tags 100000Emulate Function Key (HIS should be restarted)

Project : MYPJT1Station Name : HIS0164 Type : PC (PC) Address : 01-64 Comment : OS : Windows Vista (6.0.6000:)OPKB Revision : 0.0 Port :

Figure StationtaboftheHISSetupWindow

4 Restart HIS. The setting you made in the step 3 becomes valid.

3-8


n Usingshort-cutkeysThe setting you made earlier enables the following short-cut keys.

l EmulatedFunctionsofHISOperationKeyboard Ctrl+F1; Function of PF01(*1) Ctrl+F2; Function of PF02(*1) Ctrl+F3; Function of PF03(*1) Ctrl+F4; Function of PF04(*1) Ctrl+F5; Function of PF05(*1) Ctrl+F6; Function of PF06(*1) Ctrl+F7; Function of PF07(*1) Ctrl+F8; Function of PF08(*1) Ctrl+F9; Function of PF09(*1) Ctrl+F10; Function of PF10(*1) Ctrl+Shift+F1; Function of PF11(*1) Ctrl+Shift+F2; Function of PF12(*1) Ctrl+Shift+F3; Function of PF13(*1) Ctrl+Shift+F4; Function of PF14(*1) Ctrl+Shift+F5; Function of PF15(*1) Ctrl+Shift+F6; Function of PF16(*1) Ctrl+Shift+F7; Function of PF17(*1) Ctrl+Shift+F8; Function of PF18(*1) Ctrl+Shift+F9; Function of PF19(*1) Ctrl+Shift+F10; Function of PF20(*1)

*1: PF01 to PF20 stand for the function keys of the HIS operation keyboard, and the functions assigned to the keyboard are customizable.

l ReservedShortcutFunctionsThe following three shortcut functions are the reserved functions to the designated shortcut keys. These functions are always valid by the shortcut key actions even if emulating the HIS operation keyboard is disabled.The shortcut key actions and the corresponding functions are as follows:

Ctrl+Alt+F11; Switches the console isolation mode Ctrl+Alt+F12; Displays a menu Ctrl+Alt+Backspace; Displays User-In dialog box

3-9


3.4 Multiple-MonitorThefunctionknownasMultiple-MonitorconnectsuptofourmonitorstooneHumanInterfaceStation(HIS),anddisplayswindowsfortheoperationandmonitoringoneachmonitor.Inthiswayuptofourmonitorscanbehandledasonelarge,logicaldesktoparea(virtualdesktoparea).

TheMultipleMonitorsfeatureofWindowsisutilizedtoformthemultiple-monitoringschemeofHIS.Therefore,theoperatingenvironmentinthegeneral-purposepersonalcomputershouldbeeitherWindowsXPorWindowsVistathatsupportsthemultiplemonitors.Andthepackageforthemultiplemonitoring(LHS4600)shouldbeinstalledinthePCtoo.

n OverviewofMultiple-MonitorAn overview of Multiple-Monitor is as follows:

Up to four monitors can be connected to one HIS. A display card compatible with the Multiple Monitors feature of Windows is used for connection.

The monitors can be stacked (vertical orientation) or placed side-by-side (lateral orientation).

One monitor is designated as the main monitor and the others are the sub monitors. Multiple full-size operation and monitoring windows can be displayed at the same time. The secondary dialog that is called up from an operation and monitoring window is

displayed on the monitor where the calling window is being displayed. System Message Banner is displayed on each monitor, showing the same information. Browser Bar is displayed on each monitor. Each Browser Bar can be operated

independently. A display destination monitor can be designated when calling up an operation and

monitoring window.The following display operations can be performed on a Multiple-Monitor HIS:

Windows can be called up on a specified monitor.

Windows on a specified monitor can be erased.

The Print Screen can be executed for a specified monitor.

Windows can be transferred between the specified two monitors (shift and exchange).

The mouse cursor can be freely moved across the monitors. Operation and monitoring windows can be moved across the monitors by dragging with

mouse.

3-10


n Installing monitors The multiple monitors can be stacked vertically or placed side-by-side, as shown below. You need to setup in the Windows Display Properties on how you install the multiple monitors.

030401E.ai

Figure Monitor Arrangement in Multimonitoring

n MainMonitorandSubMonitorMultiple-Monitor uses one monitor as the main monitor and the other monitors as sub monitors. The main monitor is the monitor specified as the primary monitor in Display Properties of Windows. The Windows taskbar is only displayed on the main monitor.The System Message Banner is displayed on all monitors with the same contents. It can also be operated on all monitors.The Browser Bar is displayed on all the monitors at the same position but can be operated independently. The contents of Favorites folder are the same for all the monitors.When calling an operation and monitoring window without specifying the monitor number, the window may be displayed on the monitor where the active window locates or on the monitor where the new window is called from. If either the active window or the origin of calling is unidentifiable, the called window will be displayed on the main monitor. Moreover, the operation keyboard with 8-loop control keys behaves differently when operating the function block faceplates on the main monitor and on the sub monitor.With Multiple-Monitor, windows can be transferred between any specified pair of monitors.

SEE ALSO For details of the Multimonitoring, see the following:

Section E14. Multiple-Monitor in Reference (IM 33M01A30-40E)

4-1

IM 33M05D10-40E

4. OperatingtheInstrument FaceplateTheinstrumentfaceplateisafunctionthatdisplaysthefunctionblockstatusanddata.Inadditiontodisplayingstatusanddata,theinstrumentfaceplateisalsousedtoenterdataandchangeblockmodes.Thischapterexplainshowtooperatetheinstrumentfaceplate.

SEE ALSO For details of instrument faceplate, see the following:

Section E6. Instrument Faceplate in Reference (IM 33M01A30-40E)

Components of Instrument Faceplate are shown below.

ST

AUT IMANNR CAL AOFPV M3/H

70.0SV

98.0MV 100.0

100.0

80.0

60.0

40.0

20.0

OPN

CLS

FIC100Reactor conduitvapor pressure

MAINTENANCE

040001E.ai

0.0

Commentdisplay area

Statusdisplay area

Parameterdisplay area

Instrumentdisplay area

Operation mark

Data entry dialogbox call button

Tag nameTag comment

Block mode

Tag mark

Alarm status

Data item name

Open/close mark

Index

Manipulated outputvalue pointer

Manipulatedoutput value limit bar

Open/close mark

Engineering unit

Data

Instrument faceplate scalehigh limit

Instrument faceplate scalelow limit

Setpoint value pointer

Process variable bar

Operation setpointvalue limit bar

Cascade mark

CMP mark

Instrument mark

Calibration status

Alarm ON/OFF status

Block status

figure ComponentsofInstrumentFaceplate


4-2

IM 33M05D10-40E

4.1 EnteringDataDatacanbeenteredviaoperationfromtheDataEntrydialogboxorfromtheINC/DECOperationdialogbox.Thissectiondescribeshowtousethetwodialogbox.Howtochangetheoperationdataitemisalsoexplained.

n OperationfromtheDataEntryDialogBox1. Click on the button to display Data Entry dialog box in the instrument faceplate.

040101E.ai

100.0

0.0

FIC001

PV M3/H70.0

AUTNR

SV M3/H50.0

MV %65.1

TankA

Button to call data entry dialog box

Figure OpeningtheDataEntryDialogBox

2. The Data Entry dialog box will appear.

FIC001 TankA

040102E.ai

MV = 65.1%

DATA =

ITEM

Data entry area

Figure DataEntryDialogBox

3. Enter data in the data entry area, and press the [RETURN] key.4. If the setting exceeds the high limit or low limit, a reconfirmation window will appear.

5. Confirm the data value.


4-3

IM 33M05D10-40E

n ChangingtheDataItem1. In the displayed Data Entry dialog box, click on the item button.

FIC001 TankA

040103E.ai

MV = 65.1%

DATA =

ITEM

Item button

Figure OpeningtheDataItemChangeDialogBox

2. The Data Item Change dialog box will appear.

FIC001

040104E.ai

ITEM OK

CancelMVPPHPLPMV

Data item

Figure DataItemChangeDialogBox

3. In the Data Item Change dialog box, click on the new data item and click on the [OK] button.

ITEMMVPPHPLPMV

FIC001

040105E.ai

OK

Cancel

Click

Mouse

Figure SelectingtheDataItem

4. The item name displayed in the Data Entry dialog box will be changed.

040106E.ai

FIC001 TankA

MV = 65.1%

DATA =

ITEM

FIC001 TankA

PH = 80.0M3/H

DATA =

ITEM

Changes from [MV] to [PH]

Figure ChangetheDataItemName

In the above example, the display will change from [MV] to [PH], and changing the value of data item PH becomes possible.


4-4

IM 33M05D10-40E

n OperationfromtheINC/DECOperationDialogBox1. Use the mouse to click on the set point value pointer or the manipulated output value pointer

of the instrument faceplate with an operation pointer. The manipulated output value can be changed in the MAN mode, while the set point value can be changed in the AUT mode.

040107E.ai

100.0

0.0

FIC001

PV M3/H70.0

AUTNR

SV M3/H50.0

MV %65.1

TankA

Click one of them

Mouse

Figure OpeningtheINC/DECOperationDialogBox

The operable is shown in red. In MAN mode, if you click the set point value (in yellow), it turns red and changeable.

2. The INC/DEC Operation dialog box will appear.

040108E.ai

MV = 65.1

FIC001 [Shift-Key Mode] Pressing both...

INC button

DEC button

Figure INC/DECOperationDialogBox

3. Click on the INC button or DEC button to change the data value.4. If the setting exceeds the high limit or low limit, a reconfirmation window will appear.

5. Confirm the data value.

TIP The INC/DEC Operation dialog box will not appear if the clicked pointer cannot be changed. When test function is running, logon the TESTUSER does not pop up a reconfirmation window.


4-5

IM 33M05D10-40E

l UsingMouseintheINC/DECDialogBoxYou can increase or decrease the value shown in the INC/DEC dialog box by using your mouse with the INC/DEC buttons. By default, hold down the Shift key while you click either INC or DEC button and keep pressing the mouse button. The value will keep increasing or decreasing until you release the button. In addition to the default mode, Continuous mode and One-step mode are available.

SEE ALSO For more information about the INC/DEC operation mode using mouse, see the following:

l Using Mouse in n Data INC/DEC Operation in E6.4, Operations on Instrument Faceplate of Reference (IM 33M01A30-40E)


4-6

IM 33M05D10-40E

4.2 ChangingtheBlockModeTheoperatingstatusofafunctionblockiscalledblockmode.Thissectionexplainshowtochangetheblockmode.

Tochangetheblockmode,useeithertheBlockModeChangeOperationdialogboxorashortcutmenuforchangingblockmodes.YoumustspecifywhichtouseintheHISConstantbuilder.

n OperationfromtheBlockModeChangeOperationDialogBox1. Click on the block mode display area (the area in which the block modes such as AUT and

MAN are displayed).

040201E.ai

100.0

0.0

FIC001

PV M3/H70.0

AUTNR

SV M3/H50.0

MV %65.1

TankA

Click

Mouse

Figure OpeningtheBlockModeChangeOperationDialogBox

2. The Block Mode Change Operation dialog box will appear.

040202E.ai

FIC001

CAS buttonAUT buttonMAN button

Figure BlockModeChangeOperationDialogBox

3. In the Block Mode Change Operation dialog box, click on the mode button to be changed. For the blocks with SEMI mode, clicking on the CAS button changes the mode to SEMI.

4. Clicking any of the buttons will call a dialog box to confirm the operation.

5. Perform confirmation operation.


4-7

IM 33M05D10-40E

n ChangingBlockModeUsingtheMenu1. Click the block mode on the instrument faceplate. Then a menu with blocks modes will pop

up.

040203E.ai

Click

mouse

MANNRPV M3/H

70.0SV M3/H 100.0MV % 100.0

100.0OPN

FIC100Flowrate in TankA

MANAUTCAS

Figure MenuforChangingBlockMode

2. Select a block mode on the menu. Then a dialog box will be displayed for confirmation.

3. Confirm.


4-8


4.3 OperationMarkonInstrumentFaceplateSettinganoperationmarkonaninstrumentfaceplatecantemporarilyapplyanoperationalrestrictiontothefunctionblock.Itcanalsoputalabeltext.

Therestrictionoftheoperationmarkaswellasthelabeltextandthecolorcanbedefinedontheoperationmarkbuilder.

SEE ALSO For details of operation marks, see the following:

Section F3.5, Operation Mark in Reference (IM 33M01A30-40E)

n SettingAnOperationMark1. Open the tuning view of the function block.

Click the following button on the tuning view.

040301E.ai

Operation Mark Assignment dialog box displays.

CancelOK

040302E.ai

None

Setting

InspectionOperation prohibitedRunningOPMARK04OPMARK05OPMARK06OPMARK07OPMARK08OPMARK09OPMARK10OPMARK11OPMARK12OPMARK13OPMARK14OPMARK15

FIC100A system intake flowrate

Operation Mark Assignment

Figure OperationMarkAssignmentDialogBox

2. Check [Setting], and then select an operation mark from the list. For removing an operation mark, [None] should be checked instead of [Setting].

3. Click [OK]. The selected operation mark is set to the instrument faceplate of the function block.

4-9

IM 33M05D10-40E

n ChangingLabelTextandColorofAnOperationMarkThe label and the color of the operation mark can be changed on HIS Setup window.1. In the Tool Button Tool Box in the Browser Bar, click the button to show System Status

Overview view.

040303E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

OverviewSystem Status Overview view

Figure Opening System Status Overview View

2. System Status Overview view appears. In the view, click the button for HIS Setup.

030102E.ai

3. Open the [Operation Mark] tab on HIS Setup window.4. Enter the label text and choose a favorite color, and then click [OK].

Confirm that the label text and the color of the operation mark are changed.


4-10


4.4 TightShutandFull OpenTheTightshut/Fullopenoperationisforsecuringthetightshutorfullopenofthevalvebychangingtheactualoutputvalueaccordingtothemanipulatedvalue(MV).IftheMVis0%,toavalueoflessthan0%,andiftheMVis100%,toavalueofmorethan100%.

For tight shut or full open of the valve: If the Tight shut/Full open is required, do one of the following.

In the Data Input dialog box, enter 0 or 100 in MV. Press the INC or DEC button and keep pressing it one or two seconds longer after the MV

shown in the faceplate reaches MV=0.0% or MV=100.0%.

IMPORTANT If the output destination of the manipulated value (MV) of a function block having the Tight

shut/Full open feature is a Fieldbus Faceplate block, set the Tight shut/Full open to No in the Function Block Detail Builder.

In the Function Block Detail Builder, the setting items Output Value for Tight-shut (Ms) and Output Value for Full-open (Mf) are named assuming the valves with reverse actions where the valves close tightly if the manipulated value (MV) is 0 %. For the valves that close tightly if the manipulated value (MV) is 100 %, the setting item Output Value for Tight-shut (Ms) is a value for setting the actual output value to a value less than 0 % if the manipulated value (MV) is 0 %. Take note that the setting item Output Value for Full-open (Mf) is a value for setting the actual output value to a value more than 100 % if the manipulated value (MV) is 100 %.

5-1

IM 33M05D10-40E

5. WhenaMessageisGeneratedMessagesgeneratedduringoperationincludepredefinedmessagesanduser-definedmessages,bothofwhichareusedtonotifytheoperatorofchangesinsystemstatus,theoperation status of a process and various events occurring in a process.

Thischapterexplainshowtoconfirm/acknowledgemessagesaswellastofindthosegeneratedinthepast.


5-2

IM 33M05D10-40E

5.1 ConfirmingMessagesDifferenttypesofmessagesaregeneratedwhenmonitoring.Whenamessageisgenerated,thecorrespondingmessagebuttonwillflashinthesystemmessagewindowornavigatorwindowtonotifytheoperatorthatamessagewasgenerated.

Thissectionexplainshowtoconfirmthegeneratedmessages.

SEE ALSO For using Consolidated Alarm Management Software (CAMS for HIS), see the following:

Section E12. Consolidated Alarm Management Software in Reference (IM 33M01A30-40E)

n ConfirmingmessagesinSystemMessageBannerWhen a process alarm message, annunciator message, system alarm message or operator guide message is generated, beeps are output and the corresponding button in the System Message Banner flashes.

?Copy

00 0

2008/03/03 14:35

TESTUSER


050101E.ai

Flashes if a process alarm message or an annunciator message occurs

Flashes if a system alarm message occurs

Flashes if an operator guide message occurs

Message Display Area

Figure ButtonsintheSystemMessageBanner

1. If beeps are output, look at the flashing button in the System Message Banner to check which type of message is generated.

2. Click the Message Display area in the System Message Banner. Or click the flashing button.

3. A message window appears.


5-3

IM 33M05D10-40E

4. To acknowledge all the messages at once, click the Acknowledge button. To acknowledge each message, click the message you want to acknowledge, and then click the Acknowledge button.

5/ 5

050102E.ai

Range: All

1

2

3

4

5

08/18 04:18:33 PMReactor, high temperature!08/18 04:18:14 PMReactor operation condition error!Pressure and temperature exceed the specified values. PIC100 11 kPa TIC200 125 DEG08/18 03:17:40 PMTransfer process starts.08/18 03:17:05 PMEnter the setpoint.08/18 02:16:18 PMRaw material charge is completed.

SBP201: MSG002

Specified valus 3.5 kPa Specified valus 120.0 DEG

SBP200: MSG001

Ready

.OG Operator Guide Message

Acknowledge buttonDelete button

Figure AcknowledginganOperatorGuideMessage

5. With a group acknowledgment, all of the unacknowledged messages are acknowledged; with an individual acknowledgment, the selected messages are acknowledged.

Interactive message acknowledgment An interactive operator guide message can only be acknowledged individually. Select the operator guide message to be acknowledged in the operator guide view, then click on the acknowledge button. The operator guide individual acknowledgment window displaying the selected interactive message will appear.

050103E.ai

08/18 04:17:05 PM SBP200: MSG001

Move to the reaction process.

Move condition =

.OG Operator Guide Message

Delete buttonAcknowledge button

Figure AcknowledgingtheInteractiveMessage

TIPIn the case of an operator guide message or system alarm message, clicking on the delete button after acknowledging operation will delete the message.


5-4

IM 33M05D10-40E

n Viewing Process ReportIn the Process Report view, the information on the system operation statuses is collected. And the information is shown in a window or is printed at the request of user. The data shown in the window or printed is the current one. The following two types of Process Report are available.

Tag Report I/O Report

l Tag Report1. In the Tool Button Tool Box in the Browser Bar, click the button to display Process Report

View.

050104E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Process Report View

Figure Opening Process Report View

The process report view displays.2. Click the following button on the toolbar of the process report view.

050105E.ai


5-5

IM 33M05D10-40E

The tag report view displays the tag numbers and their state according to the conditions set in the Tag Search dialog box.

"I/O" FCS0101 %SW"TAG" DEFAULT

Tag Name Tag Comment Alarm Operation System Tag NameModeCurrent ValueFIC300 Discharge line A NR 80.0M3/H MAN .BL0158S010101TIC100 Charge tank NR 20.0DEGC MAN IMAN Maint .BL0159S010101 LIC200 Discharge tank NR 36.0L/H MAN .BL0160S010101PI150 Reactor NR 25.0PA AUT .BL0161S010101MC100 Wash valve 1 NR 0.0% MAN .BL0162S010101SIO220 Flowrate valve NR 1 MAN .BL0163S010101LSW111 Agitator NR .BL0164S010101SW330 Discharge line .BL0165S01010101ST0002 NR 2 AUT .BL0166S010101LC001 Transfer 1 NR MAN .BL0167S010101LC002 Transfer 2 NR MAN .BL0168S010101LIC001 NR 0.0% MAN .BL0169S010101LIC002 NR 0.0% MAN .BL0170S010101AN0001 Tank level error ALM 1 Maint .AN0001S010101AN0002 Pump A fail NR 0 .AN0002S010101AN0003 Tank A temp HI NR 0 .AN0003S010101AN0004 Tank B temp LO NR 0 .AN0004S010101AN0005 Tank A level HH NR 0 .AN0005S010101AN0010 Tank B level HI NR 0 .AN0010S010101AN11 Tank C level LO NR 0 .AN0011S010101

MORE

050106E.ai

.PR Process Report

Figure ProcessReportView(TagReport)

The dialog box consists of multiple tabs; only the conditions in the selected tab are applied. Click the above button again may refresh the displayed tag report.

3. Click the following button can open the Tag Search dialog box for setting conditions.

050107E.ai


5-6

IM 33M05D10-40E

Tag Search Dialog Box displays as follows.

Save AsResetCancelOK

DEFAULT SHEET1 SHEET2 SHEET3 SHEET4

050108E.ai

Tag Report Search Dialog

FCS0101

Range

Function BlockAnnunciatorCommon SwitchProcess I/OGlobal Switch

User GroupAllStation Specification

Equipment AOFCALOperation Mark

Element TypeAllSpecified Element

TagUser-Defined TagAll TagsSpecified Tag

Arbitrary Character

StateAllAlarmSpecified Alarm

...

...

ItemProcess Value of Tag Item

Arbitrary Character

Figure TagReportSearchDialogBox

4. Change a tab or click [Reset] button on this dialog box.5. Set the conditions and click [OK].

The process report will be displayed according to the new conditions.


5-7


l I/O Report1. In the Tool Button Tool Box in the Browser Bar, click the button to display Process Report

view.

050109E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Process Report view

Figure Opening Process Report View

The process report view displays.2. Click the following button on the toolbar of the process report view.

050110E.ai

The I/O report view displays the I/O points and their state according to the conditions set in the I/O Search dialog box.

"I/O" FCS0101 %AN

FCS0101

AN0000AN0050AN0100AN0150AN0200

1234567890. . 1. 1. 1. 11. 11111. 1. . . 1. 111. 11. . . 1. 11. 1. . . 111. . 1111

123456789011. 111. . . . 1. . 1. . . 1. . . 1. . . 1. 1. . 1. 1111. . . 111. . . 1. . . 1

1234567890. 111. 11. 1. . . 1. . 1. 11. 11. . . . . 111. . . . . 111. . . . 11. . . . 11

1234567890 1234567890 123456789011. . . 1. . . . . . . . . 1. . 11. 1. 1. 1. . . 1. . . . . 11. 1. 11. 1. 1. . 1.

1234567890. . . 11. . . . . . . 11. . . . . . . . . . . 1. 1. . 1. 1111. . . 1. 111. 1. . . 1

AN02501234567890. . . 1. 1

1234567890 12345678901234567890 1234567890 1234567890 1234567890

050111E.ai

.PR Process Report

"TAG" DEFAULT

Figure ProcessReportView(I/OReport)

Click the above button again may refresh the displayed I/O report.

5-8


3. Click the following button can open the I/O Search dialog box for setting conditions.

050112E.ai

The I/O Search Dialog Box displays.

CancelOK

Element Seed

FCS0101Subject Station

AnnunciatorCommon SwitchProcess I/OCommunication I/OGlobal Switch

050113E.ai

I/O Report Search Dialog

Figure I/OReportSearchDialogBox

4. Set the conditions and click [OK].

5-9


5.2 MessageSearchAmessagegeneratedinthepastcanberedisplayedforconfirmation.Tosearchforamessage,usetheFilterdialogbox,afunctionblockorthehistoricalmessagereportwindow.

SEE ALSO For using Consolidated Alarm Management Software (CAMS for HIS), see the following:


n FindingaMessageUsingtheFilterDialogBoxUse the Filter dialog box to find a process alarm message, annunciator message, operator guide message or system alarm message generated in the past. Using the filter dialog box, the messages that matched the filter conditions can be displayed separately from the display of the entire messages.The example below explains how to find a process alarm message:

1. Click on the button to display filter dialog in the process alarm view.

050201E.ai

1234

.AL Process Alarm

Ready

10/28 10:18:15 FIC005 Flowrate 5 NR 33.0M3/H NR10/28 10:18:15 FIC005 Flowrate 5 LO 33.0M3/H NR10/28 10:17:05 FIC004 Flowrate 4 DV+ 50.0M3/H DV+10/28 10:16:45 FIC003 Flowrate 3 HH 12.0M3/H HH

1.0m3/s

4/4Type: AllRange: All

Filter dialog

Figure OpeningtheFilterDialogBox

5-10


2. The Filter dialog box will appear.

CancelOK

All

Function Block Only

Annunciator Only

050202E.ai

Filter

Type

Range

All

FCS Name

Equipment Name

Tag Name

Batch ID

Safety Control Station

FCS0101

Range

%DR0001S010101 ...

Figure FilterDialogBoxfortheProcessAlarm

3. In the Filter dialog box, specify the range and type of the alarm to be searched for, then click on the [OK] button.

With a horizontal split, a view can be displayed into two frames. The filtered messages are displayed in the top frame while the whole messages are displayed in the bottom frame.

An example of the process alarm window split is shown as follows:

123

050208E.ai

.AL FCS0101 Process Alarm

Ready

07/25 15:05:32 FIC1000 Temperature Control NR07/25 15:05:32 FIC1000 Temperature Control LO07/25 15:05:30 FIC1000 Temperature Control LO

1.0m3/s

123456

07/25 15:05:32 FIC1000 Temperature Control NR07/25 15:05:32 FIC1000 Temperature Control LO07/25 15:05:30 FIC1000 Temperature Control LO07/25 15:05:45 TIC1000 Primary Temperature Control NR07/25 15:05:45 TIC1000 Primary Temperature Control LO07/25 15:05:43 TIC1000 Primary Temperature Control LO

3/3 6/6Range: Tag Name: FIC1000 Type: All

Figure Process Alarm View Split

5-11


n FindingaMessageUsingaFunctionBlockMessages associated with a function block can be called from the function block.The example below explains how to call a process alarm message from the trend view.1. Select a trend pen in the trend view.

050203E.ai

13:34

Tag Name

13:36 13:38 13:40 13:42 13:44

82.3

62.3

42.3

22.3

2.3

FIC

001.

PV

102.3

Tag Comment Value Unit Upper Lower

Gathering 00:12:00 100%

FIC001. PVFIC002. PVLIC100. PVTIC100. PVTIC200. PV

12345678

Inlet flowOutlet flowLevelTemp ATemp B

M3/hM3/hMDEGCDEGC

100.0100.0100.0100.0100.0

0.00.00.00.00.0

72.153.3

3.825.714.1

TG0101 Block:01 Group:01

ClickMouse

1

2

Figure SelectingtheFunctionBlock

2. Click the button to display the process alarm view in the System Message Banner.

?Copy

00 0

2008/03/03 14:35

TESTUSER


050204E.ai

Process alarm view

Figure Opening Process Alarm View

5-12


3. The process alarm view will open, displaying process alarm messages associated with the trend pen (FIC001) selected in the trend view.

123

050205E.ai

.AL Process Alarm

Ready

10/28 01:18:30 PM FIC001 Tank Flowrate 1 NR 50.1M3/H NR10/28 01:18:30 PM FIC001 Tank Flowrate 1 LO 72.1M3/H NR10/28 10:17:45 AM FIC001 Tank Flowrate 1 LO 72.1M3/H NR

1.0m3/s

3/3 Type: AllRange: FIC001

Figure Process Alarm View

5-13


n ConfirmingfromtheHistoricalMessageReportWindowIn the historical message report window, all messages occurred in the past, no matter if they are alarm messages, operation messages or other types of messages, are stored and can be confirmed.

1. In the Browser bar, click the button to display the Historical Report view.

NAME

050206E.ai

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Historical Report view

Figure Opening Historical Report View

5-14


2. After calling up the historical message report window, the messages in the window may be confirmed.

20 Items Found

Message No Date Message Text

Ready

File Edit View Window Help

12061201120612011206120112061201110611021101120612011206120111061102120611011201

07/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/2607/12/26

11:59:4011:59:3811:59:3711:59:3511:59:3311:59:3111:59:2911:59:2811:24:5411:24:5411:24:3411:24:0411:23:4711:23:4411:23:3110:49:3510:49:3510:49:2810:49:2310:48:58

Tank level errorTank level errorTank level errorTank level errorTank level errorTank level errorTank level errorTank level errorFIC008FIC008FIC008Pump A failAgitator failAgitator failPump A failFIC005FIC005Tank level errorFIC005Tank level error

Flowrate 8Flowrate 8Flowrate 8

Flowrate 5Flowrate 5

Flowrate 5

NRALMNRALMNRALMNRALM

NRALMNRALM

NR

ALM

NRPV = 55.0 M3/H LO RecoverPV = 50.0 M3/H LO

NRPV = 60.0 M3/H LO Recover

PV = 59.1 M3/H LO

STOP

050207E.ai

Historical Report - [Operation and Monitoring Message]

Figure Historical Message Report Window

5-15


5.3 Messages On Help WindowThehelpmessagesassignedtothefunctionblockfaceplatesandwindowsaswellasthehelpmessagesofoccurredalarmscanbedisplayedonhelpwindow.

n Help Messages of Occurred System Alarms1. In the System Message Banner, click the button to display the system alarm view.

?Copy

00 0

2008/03/03 14:35

TESTUSER


050301E.ai

System alarm view

Figure Opening System Alarm View

2. System Alarm Message view appears. Click one system alarm message and then click the button to display the Help window.

26/77Range: All

1 0823 01/14 03:20:01 Printer PRINTER 1 Offline 2 0502 01/14 02:31:02 DataBase Equalize Complete 3 0510 01/14 02:30:57 Data Base Download from YOKOGAWA File = ClsDef.odb 4 0510 01/14 02:30:57 Data Base Download from YOKOGAWA File = TrDspAssign.odb 5 0510 01/14 02:30:57 Data Base Download from YOKOGAWA File = TrAssign.odb 6 0502 01/14 02:29:33 DataBase Equalize Complete 7 0510 01/14 02:29:23 Data Base Download from YOKOGAWA File = ClsMng.odb 8 0510 01/14 02:29:23 Data Base Download from YOKOGAWA File = TrDef.odb 9 0823 01/12 09:50:03 Printer PRINTER 1 Offline 10 0502 01/12 09:28:46 DataBase Equalize Complete 11 0510 01/12 09:28:37 Data Base Download from YOKOGAWA File = OGAR010101.odb 12 0510 01/12 09:28:37 Data Base Download from YOKOGAWA File = SDAR010101.odb 13 0510 01/12 09:28:37 Data Base Download from YOKOGAWA File = Inst0357.odb 14 0510 01/12 09:28:37 Data Base Download from YOKOGAWA File = TFAR010101.odb 15 0510 01/12 09:28:37 Data Base Download from YOKOGAWA File = TFFCS0101.odb 16 0471 01/12 09:28:28 FCS0101 Online Download Complete 17 0502 01/09 06:29:46 DataBase Equalize Complete 18 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = OPSBL1.dsp 19 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = UTSW1.dsp 20 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = OPSFC1.dsp 21 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = SFCSW1.dsp 22 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = OGAR010101.odb 23 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = SDAR010101.odb 24 0510 01/09 06:29:41 Data Base Download from YOKOGAWA File = Inst0357.odb 25 0510 01/09 06:29:40 Data Base Download from YOKOGAWA File = TFAR010101.odb 26 0510 01/09 06:29:40 Data Base Download from YOKOGAWA File = TFFCS0101.odb

050302E.ai

.SA System Alarm Message

Ready

HELP

Help window

Figure OpeningtheHelpWindow

5-16

IM 33M05D10-40E

3. In the help window, the contents of the selected system alarm message appear.

Message number 0046

.HW Help

Search key

When process C starts, close the distillation tower intake valve.

Cancel

Display

050303E.ai

Figure Help Window

n User-DefinedHelpMessagesforFunctionBlocks,View,Window1. Open a faceplate or a view or window by entering the name directly or using the related

button. The faceplate or the view or window displays.

2. Activate the view or window or the faceplate on the desktop and then click the button to display the Help window on in the Tool Button Tool Box in the Browser Bar.

050304E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Help window

Figure OpeningtheHelpwindow

Help window with the help messages for the faceplate or the window is displayed.


5-17

IM 33M05D10-40E

n SearchHelpMessageOnHelpWindow1. Deactivate all the windows displayed on the desktop.2. Click the button to display the Help window in the Tool Button Tool Box in the Browser Bar.

A Help window appears.

Message number 9100

.HW Help

Search key

When process C starts, close the distillation tower intake valve.

Cancel

Display

050305E.ai

Figure Help Window

3. In the Search key area in the Help window, choose a search key from the list. The following search keys are available:

View or Window Name Tag Name Message Number Help Number

4. Enter an alphanumeric string to the field at right-hand side of the search key, and then click [Display] button. The detailed help message matches the above condition will be displayed.


5-18

IM 33M05D10-40E

5.4 ConfirmingMessagesinCAMS for HISConsolidatedAlarmManagementSoftwareforHIS(hereinafter,CAMSforHIS)iscapableofshowinginonewindowallthealarmsandeventmessagessuchassystemalarmmessages, process alarm messages, and operator guide messages.

Inaddition,itdisplaysthepastA&Emessagesandoperationrecordsofoperatorsonthewindowforthehistoricaldatalist,thatCAMSforHISkeeps.

n WhatisCAMSforHIS?CAMS for HIS has two kinds of windows.

l Message Monitor of CAMS for HISCAMS for HIS replaces the Process Alarm view, System Alarm view, and Operator Guide view with one CAMS for HIS window, CAMS for HIS Message Monitor (*1). All the messages are gathered and shown in the CAMS for HIS Message Monitor.*1: As to Operator Guide view, the message monitor of CAMS for HIS is displayed when selecting [Exclude operation guide

messages] in CAMS for HIS Tab of HIS Utility.

050401E.ai

Shelving

Filter

CAMS for HIS : Message Monitor

File Edit View Operation Tools

Data Massage

Data Massage

Favorites-

+ SIS(0/0/0)System(10/32/32)Process(0/0/0)Operator Guide(0/0/0)

TESTUSER(10/32/32)All Filters

3/4/2008 11:36:21 AM HIS Start (Virtual) 3/4/2008 11:36:21 AM FCS0101 Fail3/4/2008 11:36:21 AM STN0102 Fail3/4/2008 11:36:21 AM ACG0103 Fail 3/4/2008 11:36:21 AM HIS0164 Fail 3/4/2008 11:37:08 AM FCS0101 Recover 3/4/2008 11:37:10 AM FCS0101 RIGHT Fail (SW STOP Code=0000 0000 0000 0000) 3/4/2008 11:37:10 AM FCS0101 RIGHT Manual Reset Start 3/4/2008 11:37:10 AM FCS0101 RIGHT Control 3/4/2008 11:37:10 AM FCS0101 Batch Manager Ready 3/4/2008 1:13:08 PM DataBase Equalize Complete 3/4/2008 1:13:28 PM DataBase Equalize Complete 3/4/2008 1:13:29 PM DataBase Equalize Complete 3/4/2008 1:13:44 PM DataBase Equalize Complete 3/4/2008 1:14:42 PM DataBase Equalize Complete 3/4/2008 1:15:15 PM DataBase Equalize Complete 3/4/2008 1:15:33 PM DataBase Equalize Complete 3/4/2008 1:16:23 PM DataBase Equalize Complete 3/4/2008 1:16:35 PM FCS0101 Fail 3/4/2008 1:16:41 PM HIS Shutdown 3/4/2008 1:17:38 PM HIS Start (Virtual) 3/4/2008 1:17:38 PM FCS0101 Fail 3/4/2008 1:17:38 PM STN0102 Fail 3/4/2008 1:17:38 PM ACG0103 Fail 3/4/2008 1:17:38 PM HIS0164 Fail 3/4/2008 1:18:25 PM FCS0101 Recover 3/4/2008 1:18:27 PM FCS0101 RIGHT Fail (SW STOP Code=0000 0000 0000 0000)3/4/2008 1:18:27 PM FCS0101 RIGHT Manual Reset Start 3/4/2008 1:18:27 PM FCS0101 RIGHT Control 3/4/2008 1:18:27 PM FCS0101 Batch Manager Ready 3/4/2008 1:19:46 PM DataBase Equalize Complete 3/4/2008 1:19:55 PM DataBase Equalize Complete

3/4/2008 11:36:21 AM HIS Start (Virtual) 3/4/2008 11:36:21 AM FCS0101 Fail3/4/2008 11:36:21 AM STN0102 Fail3/4/2008 11:36:21 AM ACG0103 Fail 3/4/2008 11:36:21 AM HIS0164 Fail 3/4/2008 11:37:08 AM FCS0101 Recover 3/4/2008 11:37:10 AM FCS0101 RIGHT Fail (SW STOP Code=0000 0000 0000 0000) 3/4/2008 11:37:10 AM FCS0101 RIGHT Manual Reset Start 3/4/2008 11:37:10 AM FCS0101 RIGHT Control 3/4/2008 11:37:10 AM FCS0101 Batch Manager Ready

Figure CAMS for HIS Message Monitor View


5-19

IM 33M05D10-40E

l Historical Viewer of CAMS for HISHistorical Viewer of CAMS for HIS can hold the occurred A&E messages and operational audit trails; and display the stored historical data.Historical Viewer of CAMS for HIS is a replacement of Historical Message Report Window.

050402E.ai

Filter

CAMS for HIS : Historical Viewer

File Edit View Operation

Data MassageFavorites-

+ SIS(0/0/0)System(10/32/32)Process(0/0/0)Operator Guide(0/0/0)

TESTUSER(10/32/32)All Filters

TESTUSER - Current User

3/4/2008 11:36:21 AM HIS Start (Virtual) 3/4/2008 11:36:21 AM FCS0101 Fail3/4/2008 11:36:21 AM STN0102 Fail3/4/2008 11:36:21 AM ACG0103 Fail 3/4/2008 11:36:21 AM HIS0164 Fail 3/4/2008 11:37:08 AM FCS0101 Recover 3/4/2008 11:37:10 AM FCS0101 RIGHT Fail (SW STOP Code=0000 0000 0000 0000) 3/4/2008 11:37:10 AM FCS0101 RIGHT Manual Reset Start 3/4/2008 11:37:10 AM FCS0101 RIGHT Control 3/4/2008 11:37:10 AM FCS0101 Batch Manager Ready 3/4/2008 1:13:08 PM DataBase Equalize Complete 3/4/2008 1:13:28 PM DataBase Equalize Complete 3/4/2008 1:13:29 PM DataBase Equalize Complete 3/4/2008 1:13:44 PM DataBase Equalize Complete 3/4/2008 1:14:42 PM DataBase Equalize Complete 3/4/2008 1:15:15 PM DataBase Equalize Complete 3/4/2008 1:15:33 PM DataBase Equalize Complete 3/4/2008 1:16:23 PM DataBase Equalize Complete 3/4/2008 1:16:35 PM FCS0101 Fail 3/4/2008 1:16:41 PM HIS Shutdown 3/4/2008 1:17:38 PM HIS Start (Virtual) 3/4/2008 1:17:38 PM FCS0101 Fail 3/4/2008 1:17:38 PM STN0102 Fail 3/4/2008 1:17:38 PM ACG0103 Fail 3/4/2008 1:17:38 PM HIS0164 Fail 3/4/2008 1:18:25 PM FCS0101 Recover 3/4/2008 1:18:27 PM FCS0101 RIGHT Fail (SW STOP Code=0000 0000 0000 0000)3/4/2008 1:18:27 PM FCS0101 RIGHT Manual Reset Start 3/4/2008 1:18:27 PM FCS0101 RIGHT Control 3/4/2008 1:18:27 PM FCS0101 Batch Manager Ready 3/4/2008 1:19:46 PM DataBase Equalize Complete 3/4/2008 1:19:55 PM DataBase Equalize Complete

Figure Main Window of CAMS for HIS Historical Viewer


5-20

IM 33M05D10-40E

n Setting up for CAMS for HISBefore using CAMS for HIS, you must set up in the HIS Utilities. Follow the steps below for the setup. 1. Start the HIS Utilities.2. Click the CAMS for HIS tab. Select the checkbox for validating CAMS for HIS. Set other

items such as the maximum number of alarms to be held, as necessary. 3. Restart the PC. 4. Import the engineering data for CENTUM VP. Based on the data, create setup files such as

Alarm Setup and Window Layout Setup. 5. Download the setup files.

You can create and download setup files by starting the CAMS for HIS Configurator on any HIS PC.

SEE ALSO For details of setting up CAMS for HIS, see the following:

Section E12.10, Configurator of CAMS for HIS in Reference (IM 33M01A30-40E)

Section E12.2, Settings to Use CAMS for HIS in Reference (IM 33M01A30-40E)

n Starting Message Monitor of CAMS for HIS

l IntheSystemMessageBannerIn the System Message Banner, click the button to call Process Alarm view, System Alarm view, or Operator Guide view. The CAMS for HIS Message Monitor View appears with the filtering conditions of each window on.

?Copy

00 0

2008/03/03 14:35

TESTUSER


050403E.ai

Process Alarm

System Alarm

Operator Guide

Figure SystemMessageBanner

2nd Edition : Dec.22,2009-00

5-21

IM 33M05D10-40E

l IntheBrowserbar(ToolButtonToolBox)Click the button for CAMS for HIS in the Tool Box on the Browser Bar.CAMS for HIS Message Monitor View will start.

050406E.ai

NAME

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

CAMS for HIS

Figure Opening CAMS for HIS Message Monitor View


5-22

IM 33M05D10-40E

l IntheBrowserbar(NameInputToolBar)In the Name Input Tool Box, call Process Alarm view, System Alarm view, or Operator Guide view. The CAMS for HIS Message Monitor View appears with the filtering conditions of each window on.

050404E.ai

Name Input

NAME

Window Name Input

Call

Default Station Information

Figure NameInputToolBoxintheBrowserBar


5-23

IM 33M05D10-40E

n Starting Historial Viewer of CAMS for HIS

l StartfromBrowserBarClick the button to display the Historical Report View in the Tool Box on the Browser Bar.CAMS for HIS Historical Viewer will start.

NAME

050405E.ai

Tool Button

HELPSYS ?

View Operation

Call View

Window Control

Builder

Overview

Historical Report

Figure Opening CAMS for HIS Historical Viewer

SEE ALSO For the features of CAMS for HIS, see the following:



Blank Page

6-1

IM 33M05D10-40E

6. ReadingtheTrendofProcessDataUsethetrendrecordingtoreadthetrendofpastdata.Withthetrendrecording,processdataacquiredfromtheplantcanbesavedandthesaveddatacanbedisplayed.


6-2

IM 33M05D10-40E

6.1 ConfirmingDataintheTrendViewTheacquireddatacanbedisplayedinthetrendview.

Inthetrendview,datacanbedisplayedasitisacquired,orpreviouslyacquireddatacanbedisplayedagain.

n DisplayingAcquiredDataintheTrend View1. Call the trend view.

SEE ALSO For the steps to call the trend view, see the following:

Section E5, Trend Recording in Reference(IM33M01A30-40E)

2. The trend view displays the acquired data in a graph or the present values in numeric values.

060101E.ai

13:34

Tag Name

13:36 13:38 13:40 13:42 13:44

82.3

62.3

42.3

22.3

2.3

FIC

001.

PV

102.3


Gathering 00:12:00 100%


12345678


M3/hM3/hMDEGCDEGC

100.0100.0100.0100.0100.0

0.00.00.00.00.0

72.153.3

3.825.714.1

TG0101 Block:01 Group:01

1

2

Figure Trend View


6-3

IM 33M05D10-40E

n Displaying Collected Data On Trend Point View1. Double click a tag name in the trend view, or choose a trend pen and click [Display] key, the

corresponding trend point view can be displayed.

060102E.ai

FIC001. PV Inlet flow

16:22

Tag Name

16:23 16:24 16:25 16:26 16:27

FC01

.PV


3 FC01. PV 81.1 KL/h 500.0 0.0

82.3

62.3

42.3

22.3

2.3

102.3

Figure Trend Point View

When a batch trend is displayed, if a reference pattern is assigned to the displayed trend pen the reference pattern will be displayed too.


6-4

IM 33M05D10-40E

6.2 ChangingtheAssignmentofTrendDataBeingDisplayed

Theassignmentoftrendpensbeingdisplayedinthetrendwindowcanbechanged.TheassignmentoftrendgroupcanbechangedbyusingthePenAssignmentdialogboxorbyselectingafileinwhichtrenddataissavedbyusingadrag-and-dropoperationintheBrowserbar.

Thissectionexplainshowtochangetheassignmentoftrendpens.


6-5

IM 33M05D10-40E

n ChangingthePenAssignmentinthePenAssignmentDialogBox1. In the trend view, click on the following button on the tool bar.

060201E.ai

2. The Pen Assignment dialog box will appear.

Pen Assignment

060202E.ai

CollectedBlock Lower DisplaySet Upper/Lower Limit

LIC800.PV4: Rotary 05min. ... 8

7

6

6

5

4

AIC200.PV2: Rotary 01min. ... 2

FIC100.PV1

Cancel

Initialize

OK

Pen Assignment

Reference Pattern

Figure PenAssignmentDialogBox(PenAssignment)

3. Set the data to be acquired and high/low limits in the Pen Assignment dialog box. If high/low limits are not specified, the trend graph to be displayed will use the values defined via the trend gathering pen assignment builder.

4. To display desired data in the trend view, mark off the corresponding check box under [Display].

5. Click on the [OK] button.6. The trends checked in the pen assignment dialog box will be displayed.


6-6

IM 33M05D10-40E

n ChangingthePenAssignmentviaFileSelection1. In the trend view, click on the following button on the tool bar.

060203E.ai

2. A dialog box will appear; choose a file in which trend data is saved.

Open

Look in:

File name:

File comment

Files of type:

060204E.ai

Name Date modified Type Size

Preserved File (*.trf)

Open

Cancel

TG0101.trf

Trend

TG0101.trfTG0102.trfTG0103.trf

This folder is empty.Recent Places

Desktop

Administrator

Computer

Network

Figure OpenDialogBox

3. Select a desired file.

4. Click on the [Open] button.5. The data saved in the selected file will be displayed in the current trend view.


6-7

IM 33M05D10-40E

n ChangingthePenAssignmentusingaDrag-and-DropoperationinBrowserbar

1. In the Browser bar, click the the tag of the folder containing Trend setup data and trend data. Drag-and-drop it to the graph.

1

2

CommentAddress /USER

Favorite favorite-1 MYPJT1 .SH GR0002 favorite-2 TG0216 CG0001

OverviewView Trend Plant

NAME

Search

PP

060205E .ai

TR003

TR003

TR004

GROUP01

TR002GROUP01

TAG001.PV

TAG002.PV

TAG003.PV

TAG004.SV

13:34

Tag Name

13:36 13:38 13:40 13:42 13:44

82.3

62.3

42.3

22.3

2.3

FIC

001.

PV

102.3


Gathering 00:12:00 100%


12345678


M3/hM3/hMDEGCDEGC

100.0100.0100.0100.0100.0

0.00.00.00.00.0

72.153.33.8

25.714.1

TRTANK Tank A

Drag and drop

Figure Drag and Drop Tag Data

2. Pen is assigned, and the data in the folder is shown in the Trend graph view.

TIPPens are assigned from the top (1) to the bottom (8). The highest number of available pen is assigned. If the maximum 8 pens are already assigned, an assignment error is raised. In this case, delete some of the existing unneeded pen assignments before adding a new pen assignment.


6-8


6.3 Creating/Displaying Trend Reference Patterns

Inthetrendview,trendreferencepatternsthatareusedastemplatesfortrendgraphscanbedisplayed.

Thissectionexplainshowtocreateanddisplaytrendreferencepatterns.

n Creating a Trend Reference Pattern1. In the trend view, click on the following button on the tool bar.

060301E.ai

2. A dialog box to save trend data will appear.

Save As

Search

File name :

This Folder is Empty.

Save

his operation centum vp

Documents