foamular extruded polystyrene (xps) · pdf filetechnical bulletin foamular® extruded...

Technical Bulletin FOAMULAR ® Extruded Polystyrene (XPS) Insulation ASTM C578—Types and Physical Properties This table outlines the basic physical property requirements of ASTM C578 1 and FOAMULAR ® XPS insulation compliance. The products are organized, left to right, in ascending compressive strength. For complete details on board types, properties and other quality requirements see the actual ASTM standard. Polystyrene Board Type 2 EPS EPS EPS FOAMULAR ® 150, XPS EPS FOAMULAR ® 250, XPS EPS FOAMULAR ® 400, XPS EPS FOAMULAR ® 600, XPS EPS FOAMULAR ® 1000, XPS ASTM C578 Classification Type XI Type I Type VIII Type X Type II Type IV Type IX Type VI Type XIV Type VII Type XV Type V Compressive resistance at yield or 10 % deformation, whichever occurs first (with skins intact) min, psi (kPa) 5.0 (35) 10.0 (69) 13.0 (90) 15.0 (104) 15.0 (104) 25.0 (173) 25.0 (173) 40.0 (276) 40.0 (276) 60.0 (414) 60.0 (414) 100.0 (690) Density, min, lb/ft 3 (kg/m 3 ) 0.70 (12) 0.90 (15) 1.15 (18) 1.30 (21) 1.35 (22) 1.55 (25) 1.80 (29) 1.80 (29) 2.40 (38) 2.20 (35) 2.85 (46) 3.00 (48) Thermal resistance of 1.00-in. (25.4-mm) thickness, min, hr•ft 2 •°F/Btu (K·m 2 /W) Mean temperature: 75 2°(24 1°C) 3.10 (0.55) 3.60 (0.63) 3.80 (0.67) 5.00 (0.88) 4.00 (0.70) 5.00 (0.88) 4.20 (0.74) 5.00 (0.88) 4.20 (0.74) 5.00 (0.88) 4.30 (0.76) 5.00 (0.88) Flexural strength, min, psi (kPa) 10.0 (70) 25.0 (173) 30.0 (208) 40.0 (276) 35.0 (240) 50.0 (345) 50.0 (345) 60.0 (414) 60.0 (414) 75.0 (517) 75.0 (517) 100.0 (690) Water vapor permeance of 1.00-in. (25.4-mm) thickness, max, perm (ng/Pa·s·m 2 ) 5.0 (287) 5.0 (287) 3.5 (201) 1.5 (86) 3.5 (201) 1.5 (86) 2.5 (143) 1.1 (63) 2.5 (143) 1.1 (63) 2.5 (143) 1.1 (63) Water absorption by total immersion, max, volume 4.0 4.0 3.0 0.3 3.0 0.3 2.0 0.3 2.0 0.3 2.0 0.3 1. ASTM C578-10, “Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation”; published by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959 2. XPS is extruded polystyrene. EPS is expanded polystyrene, also known as molded polystyrene. OWENS CORNING FOAM INSULATION, LLC ONE OWENS CORNING PARKWAY TOLEDO, OHIO 43659 1-800-GET-PINK ® www.owenscorning.com Pub. No. 10015702. Printed in U.S.A. September 2011. THE PINK PANTHER™&©1964-2011Metro-Goldwyn-MayerStudiosInc.AllRights Reserved. The color PINK is a registered trademark of Owens Corning. ©2011 Owens Corning. Disclaimer of Liability Technical information contained herein is furnished without charge or obligation and is given and accepted at recipient’s sole risk. Because conditions of use may vary and are beyond our control, Owens Corning makes no representation about, and is not responsible or liable for the accuracy or reliability of data associated with particular uses of any product described herein. Nothing contained in this bulletin shall be considered a recommendation.

Upload: vokiet

Post on 06-Feb-2018

214 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Technical Bulletin

FOAMULAR® Extruded Polystyrene (XPS) InsulationASTM C578—Types and Physical Properties

This table outlines the basic physical property requirements of ASTM C5781 and FOAMULAR® XPS insulation compliance. The products are organized, left to right, in ascending compressive strength. For complete details on board types, properties and other quality requirements see the actual ASTM standard.

Polystyrene Board Type2 EPS EPS EPSFOAMULAR®

150, XPS EPSFOAMULAR®

250, XPS EPSFOAMULAR®

400, XPS EPSFOAMULAR®

600, XPS EPSFOAMULAR®

1000, XPS

ASTM C578 Classifi cation Type XI Type I Type VIII Type X Type II Type IV Type IX Type VI Type XIV Type VII Type XV Type V

Compressive resistance at yield or 10 % deformation, whichever occurs fi rst (with skins intact) min, psi (kPa)

5.0 (35) 10.0 (69) 13.0 (90) 15.0 (104) 15.0 (104) 25.0 (173) 25.0 (173) 40.0 (276) 40.0 (276) 60.0 (414) 60.0 (414) 100.0 (690)

Density, min, lb/ft3 (kg/m3) 0.70 (12) 0.90 (15) 1.15 (18) 1.30 (21) 1.35 (22) 1.55 (25) 1.80 (29) 1.80 (29) 2.40 (38) 2.20 (35) 2.85 (46) 3.00 (48)

Thermal resistance of 1.00-in. (25.4-mm) thickness, min, hr•ft2•°F/Btu (K·m2/W)Mean temperature: 75 2°(24 1°C)

3.10 (0.55)

3.60 (0.63)

3.80 (0.67)

5.00 (0.88)

4.00 (0.70)

5.00 (0.88)

4.20 (0.74)

5.00 (0.88)

4.20 (0.74)

5.00 (0.88)

4.30 (0.76)

5.00 (0.88)

Flexural strength, min, psi (kPa) 10.0 (70) 25.0 (173) 30.0 (208) 40.0 (276) 35.0 (240) 50.0 (345) 50.0 (345) 60.0 (414) 60.0 (414) 75.0 (517) 75.0 (517) 100.0 (690)

Water vapor permeance of 1.00-in. (25.4-mm) thickness, max, perm (ng/Pa·s·m2)

5.0 (287) 5.0 (287) 3.5 (201) 1.5 (86) 3.5 (201) 1.5 (86) 2.5 (143) 1.1 (63) 2.5 (143) 1.1 (63) 2.5 (143) 1.1 (63)

Water absorption by total immersion, max, volume 4.0 4.0 3.0 0.3 3.0 0.3 2.0 0.3 2.0 0.3 2.0 0.3

1. ASTM C578-10, “Standard Specifi cation for Rigid, Cellular Polystyrene Thermal Insulation”; published by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959

2. XPS is extruded polystyrene. EPS is expanded polystyrene, also known as molded polystyrene.

OWENS CORNING FOAM INSULATION, LLCONE OWENS CORNING PARKWAYTOLEDO, OHIO 43659

1-800-GET-PINK®

www.owenscorning.com

Pub. No. 10015702. Printed in U.S.A. September 2011. THE PINK PANTHER™ & ©1964-2011 Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved. The color PINK is a registered trademark of Owens Corning. ©2011 Owens Corning.

Disclaimer of LiabilityTechnical information contained herein is furnished without charge or obligation and is given and accepted at recipient’s sole risk. Because conditions of use may vary and are beyond our control, Owens Corning makes no representation about, and is not responsible or liable for the accuracy or reliability of data associated with particular uses of any product described herein. Nothing contained in this bulletin shall be considered a recommendation.

Extruded Polystyrene Insulation in Commercial Roof Systems

Barbara A. Fabian, Owens Corning Tallmadge, OH … OH 44278; ... Extruded Polystyrene Foam Association Woodbridge, VA 22193 Alisa Hoffee, Pactiv Corporation Atlanta, GA 30328; USA

Extruded Polystyrene (XPS) Rigid Foam Insulation …€¦ · Product Data Sheet FOAMULAR® Tapered Roofi ng Products Extruded Polystyrene (XPS) Rigid Foam Insulation • Lightweight,

Polyfoam Floorboard - SIG Insulation Floorboard.pdf · Polyfoam Floorboard is a high performance, 100% ozone friendly, extruded polystyrene, rigid board insulation. ... • Under

Insul-Drain Submittal Sheet FOAMULAR Extruded Polystyrene

Thermal Insulation materials - Belt Power · 2020. 11. 3. · There are also other insulation elements, such as expanded polystyrene, extruded polystyrene, PU foam, and others, but

Typical combined system - Cabrillo Collegesmurphy/Hydronic heating- radiant floors.pdftreated wood sil 6" block (top course extruded polystyrene edge insulation welded wired reinforcing,

Insulation for a better tomorrow URSA XPS - CMT · 2018-10-05 · Extruded polystyrene for thermal insulation of buildings Extruded polystyrene URSA XPS is an excellent thermal insulator

THE FOAMULAR HIGH DENSITY EXTruDED …insulation.owenscorning.ca › assets › 0 › 188 › 273f08c7-2b0e-41...the life Cycle costs associated with one of the most important, but

The FOAMULAR® Extruded Polystyrene (XPS) Insulation family of rigid foam board products is here to offer these solutions. Together with EcoTouch® insulation and housewrap, FOAMULAR®

STYROFOAM ™ Brand SM Extruded Polystyrene Foam Insulation

IntePro PS - Inteplast · IntePro® PS board is comprised of a dense polystyrene foam center with smooth solid polystyrene on both faces. The three layers are co-extruded, providing