fl tool catalog

Quick ChangeTapered Toolholders Quick-change tapered toolholders are designed and built to increase product quality by accurately positioning cutting tools on production and non-production machines. They feature improved cutting tool centerline accuracy, positive drive ofthe cutting tool and thru-coolant capability.

Each patented tapered toolholder also features a compact design which minimizes spindle to spindle center distance as well as overhang from the bearing diameters to the spindle end, making the system ideal for single and mUltiple spindle stub drilling applications without the use of costly bushing plates.

Six separate body sizes are available to accommodate a wide variety of tool shank diameters beginning at V16-inch (1.5mm) diameter. Each tapered toolholder assembly features a guaranteed accuracy of 0.0005 T.I.R. runout 2-in. from the collet face measured by a zero spindle and class XX gage pin.

Special holders, such as extended lengths and solid soft blank nosepieces for cutter inserts, can also be designed and manufactured to customer specifications.

Quick Change Tapholders 51 Series quick change tapholders are especially designed for applications in which machine feed does not exactly match that produced by t he tap pitch . Parallel float compensates for misal ignment conditions between the hole to be tapped and the machine spindle.

51 Series tapholders offer: • Quick change- a finger operated sleeve enables

fast tool change to reduce machine downtime. • Close center tooling- the small overall toolhold

er diameter allows too ling on close center distances.

• Sensitive pressure compensation-a compression spring neutralizes feed rate variations to ensure that ideal pressure is applied to the tool at the beginning of the cut.

• Built-in protection-if the drilling operation has been omitted, tool holders collapse within themselves to prevent tool breakage. All tapholder models are available w ith or without compression and tension features.

Hydraulic Chucks Hydraulic expansion chucks guarantee a maximum runout of 0.00012-inches at two times the tool shank diameter. This provides a balanced chip load and increased part quality. Reduced wear pro longs tool life as much as 300 percent.

Hydraulic expansion chucks can be operated at very high speeds. Additional balancing is recommended for speeds above 15,000 RPM. The special resilient sleeve design enables hydraulic expansion chucks to clamp cylindrica l shanks up to 1.250-inch diameter and Weldon flats shanks up to 0.75-inch.

The slimmer design of all hydraul ic chucks permits operation in difficult working situations. Interchangeable collet types can be inserted with variable shank diameters using one hydraulic expansion chuck. The radial runout ofthese hydraulic chucks with collets is less than 0.0002-inch.

The complete line of hydraulic chucks includes CAT, BT, HSK and flange-mounted models. Each chuck style is available with thru -coolant capacity.

Quick-Change Straight ShankToolholders Straight shank tool holders and automotive collettype holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design . Benefits of the system include increased machining efficiency, high accuracy repeatability and quick-change ability .

Each straight shank toolholder assembly includes a body, collet, collet nut and snap ring, positive drive and preset screw assembly as well as a rubber washer for thru-coolant applications. In operation, the tool holder is locked into the spindle by rotating the spind le mounted collar against the Acme left hand thread on the tool holder body.

Three different body sizes are available in each model to accommodate tools ranging from 7/ 64

(2 .7788 mm) to 3J4-inch (19.0500 mm) in diameter. Each straight shank holder series features a guaranteed accuracy within 0.001 T.I.R. runout 2-inches from the collet face . This is measured by a zero spindle and a class XX gage pin.

Over.:rhe-Spindle Adapter AsselDblies Over-the-spindle adapters transform standard high production machine spindles into quick-change adjustable tool adapters. They can be used with straight shank holders, automotive collet type holders or existing automotive shank tool holders by using a standard spindle collar and adapter nut assembly.

Located directly onto the spindle outside diameter and securely fastened by a locking set screw, the over-thespindle adapter assemblies feature a left-hand threaded collar that forces an Acme left hand threaded adapter nut to seat directly against the spindle face. This enables the sp indle to take the thrust generated by the tool, el im inating any thrust being directed to the set screw.

When loosened, the mechanically activated over-the -spindle adapter

(standard or stub model) forces chips away from the spindle face . Details are hardened and ground for consistent accuracy and are available to f it every machine builder's standard spindles.

Collets Precision collets feature a single angle design D.D. with a ground and lapped I.D. manufactured to within 0.0001inches ofthe required tool shank diameter. A single split through the collet allows tool clamping without losing accuarcy, unlike other collets with mul tiple splits which lose accuracy while allowing wider tool shank ranges. Six individual col let sizes are available to accommodate tools ranging from 1/16

inch to Pis-inches in diameter. These collets can be used in conjunc

tion with tapered and stra ight shank tool holders or w ith other tool holder designs where clamping accuracy is essential.

Precision Spindles In addition to quick-change tool holders and accessories, FLTool Holders has years of experi ence with the very close tolerance work required for sp indle manufacturing today.

When existing spindle designs are available, FL-Tool Holders can assist clients in determin ing the operations needed to complete the spindle and to manufacture complete spindles to meet specific customer requirements.

Spindles and toolholders are used in many manufacturing plants throughout North America . Among the companies that benefit from using FL-Tool Holders are:

• Ford Motor Company: Engine block, cylinder head, crankshaft, camshaft; transmission carrier, stator support, va lve bodies.

• General Motors Corporation: Cylinder head, cam carrier and rear axle bolt holes.

• Chrysler Corporation: Cylinder head retoo l, exhaust manifold and transmission case.

• Litton Industrial Automation: Lamb Technicon Division • Giddings & Lewis • Ann Arbor Machine • R&B Machine • Standard Machine • Western Machine

Gun DrilllReamer Toolholders Gun drill/reamer holders provide a guaranteed accuracy of 0.0001 T.I.R., two inches from the front face of the collet. This toolholder is available in four separate sizes to accommodate tool shank sizes of V4, 5/16, 3/8, 7/16, V2, 9/16, 5/8,

1V16 and 3f4-inches. The basic construction of the holder assembly includes

a Jacobs type beveled tooth nosepiece, a precision tapered collet and nut assembly that securely clamps and unclamps the tool from the holder and an internal flat that provides positive drive for the tool. Each tool holder also features thru-coolant capability and radial positioning for diamond tipped tools.

Toolsetting Fixtures FL-Tool Holders manufactures and stocks various kinds of toolsetting fixtures. Among the systems available are turret type, flange type, slide type, electronic and indicator. SOV tapered adapters, replaceable bushings and special applications can be designed and built to accommodate specific customer requirements.

36010 Industrial Road - Livonia, Michigan 48150 Telephone 734-591-0134 - FAX 734-591-7866

www.fltoolholders.com

Litho In USAAGC-377/94

FL-Tool Holders

Quick-Change Tapered Tool Holders Increase Positioning Accuracy to Improve Product Quality Quick-change tapered

Tool holder Assemblies are designed and built to increase product quality by positioning cutting tools accurately on production and non-production machines . The tapered tool holder assembly is available in six separate body sizes to accommodate a wide variety of tool shank diameters beginning at 1/16-inch (1.5 mm) diameter.

Each patented tool holder features a precision full length tapered 0 .0 . shank (3.500 inches/ foot on diameter) and I. O. tapered collet seat (10° included) to locate the cutting tool centerline accurately.

Positive drive of the tool is achieved by a non-rotating square drive that accepts the tool tang as well as an adjustable preset screw for adjusting tool height.

Mounted to the spindle, the collar is rotated in a clockwise direction to mate with the Acme left hand thread on the tool holder body seating the taper into the spindle. (See photo illustration on page 3.)

The tapered tool holder's compact design minimizes spindleto-spindle center distance as well as overhang from the spindle end to the bearing journal diameters. Thru-coolant

Capability is provided for in each tool holder body size.

These features make tapered tool holders ideally suited to meet the demands of today's manufacturing specifications for multiple spindle applications . Additional services include training, designing and building specials , modification of standards and spindle manufacturing.

Tapered tool holder assemblies feature a guaranteed accuracy of .0005 TI.R. runout 2-inches our from the collet face.

2------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Tapered Tool Holders

System Operation 1. 3 .

To load the quick·change tapered tool holder ,simply inert the holder into the corresponding machine tool spindle.

2.

Keep advancing the tapered shank holder into the spindle until it comes to a stop. At this point, the Acme left hand thread will be positioned against the spindle collar.

Rotate the spindle mounted collar in a clockwise direction until tapers are seated. Tighten securely with spindle collar wrench.

Table of Contents Tool Holder and Spindle Collar Assembly ......... .. ... 4

Collet and Nut Assembly .. .. ........ .......... ............ . 4

Tapered Tool Holder Assembly with Collet. ... ..... .. .. 5

Tapered Tool Holder Assem bly without Collet.. .. .. ... 6

Tapered Tool Holder with Collet Nut ........ .... .. ........ 7

Tapered Tool Holder Blank...... .......... .... . .... ...... .. 7

Tapered Tool Holder Components ....... .. .. .. .. ......... 8

Quick Change Tapered Body ............... .. .......... .... 8

Tool Holder Seal and Snap Ring .... ... .. .. . .. .. .......... 8

Collet Nut .. . ... ... .. .. ...... ...... ...... .. .... .......... . ......... 9

Collet Snap Ring .. .. ..... ...... .. .... ..... ......... ...... .. .. . 9

Collets ............ ... ... . ........... ... .... ... .. ... ............ .. . 9

Positive Drive and Pre-Set Screw Assembly ...... .. ... 10

Rubber Washer ... ......... ... ............ .. ... ' " ... ... ... .. .. 11

Spindle Components ............. ....... .. .... ... .. ... .. .. .. .. 12

Spindle Collar and Retaining Ring ....... ..... ... ... ... .. 12

Open End Spindle Wrench ........ . ........ ... . .... .. ...... . 12

Open End Spindle Collar Wrench ...... ...... ... ...... .... 12

Socket Spindle Collar Wrench... ... .. . ... ...... ... ... .... 13

Holding Adapter for Tool Change .. . ... ........... ........ . 13

Spindle Cleaning Swab ........ .... """ ............. .. ..... 13

Tool Setting Fixture Assembly .. .... ..... ...... .... .. .. .... 14

. Tool Setting Fixture ........................................... 14

Screwdriver Adapter .. .. .. .... .... . ..... .. ... .... . .. . .. . .. .... 14

Tool Setting Fixture ...... .............. ....... .. .. ...... ...... 14

Toque Wrench (3/8" Drive) .. .. ..... ... ... .. ............ ..... 15

Crowsfoot for Collet Nut. .. ........ . ........... .......... .... . 15

Snap Ring Pliers ...... .............. .. ......................... 15

Toolsetting Fixtures .. . .. .......... .................... ...... .. 16

This is measured by a zero spindle and a class XX gage pin. ------------~----~----------~----~~--------------------------------------3

PHONE: 734·591·0134· FAX: 734-591·7866

GAGE LINE

COLLET SNAP RING

FL-Tool Holders

Tool Holder and Spindle Collar Assembly ~---H---~

TOOL SET RANGE -IMiN~UM I :'LEAR.

E REF.

D REF.

B /,--SPDL. - ~ - -DIA. 'ii. ___r-"1:I..__lJ

GAGE LINE SPINDLE END

SERIES A·TOOL SIZE

INCHES A·TOOL SIZE

MM B·MIN. SPOL.

C·MIN. CENTER

0 REF .

E REF.

F REF .

G REF. MIN.

H MAX

1002 .0625 .2500 1.5875 6.3500 .940 1.375 1.10 1.20 1.27 1.06 1.12 1.85

2002 .0625 .3750 1.5875 9.5250 1.315 1.750 1.37 1.47 1.65 1.06 1.20 2.60

3002 .1094 .5000 2.7788 12.7000 1.565 2.000 1.53 1.63 1.90 1.06 1.50 3.10

4002 .1094 .7500 2.7788 19.0500 2.065 2.500 1.57 1.74 2.40 1.06 2.30 4.00

5002 .2500 1.0000 6.3500 25.4000 2.565 3.00 1.90 2.10 2.88 1.18 3.00 4.80

6002 .3750 1.3750 9.5250 34.925 3.06 3.50 2.06 2.26 3.38 1.18 2.70 5.30

Collet and Nut Assembly

COLLET NUT~ MINIMUMCLEARANCE

CO~ff _~I

~ F ~

NOTE: The collet and nut are not sold as an assembly. See individual components for part numbers.

SERIES TOOL SIZE

INCHES TOOL SIZE

MM A B C 0 E F

1002 .0625 .2500 1.5875 6.3500 .22 .12 .48 .438 .87 .75 HEX

2002 .0625 .3750 1.5875 9.5250 .22 .12 .57 .563 1.23 1.06 HEX

3002 .1094 .5000 2.7788 12.7000 .26 .16 .64 .720 1.44 1.25 HEX

4002 .1094 .7500 2.7788 -19.0500 .30 .19 .70 1.131 2.02 1.75 HEX

5002 .2500 1.0000 6.3500 25.4000 .42 .21 .84 1.446 2.50 2.50 OIA

6002 .3750 1.3750 9.525 34.925 .47 .21 .84 1.910 3.00 3.00 DIA

t<tSPINDLE

__

C SPINDLE

TO SPINDLE I M~N. CENTER ~ISTANCE

J

TOOL RANGE

NOTE: Full scale drawing templates of tool holder assemblies and components are available for assistance in tool layouts, alterations or new designs. FL-Tool Holders will supply CAD disks upon request.

4--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150


Tapered Tool Holder Assembly with Collet

NOTE: Tool Holder assembly includes Body, Collet, Collet Nut, Collet Snap Ring, Tool Holder Seal, Tool Holder Snap Ring, Positive Drive and Pre-Set Screw Assembly. Ordering Information

SERIES A·TOOL SIZE

INCHES A·TOOL SIZE

MM PART NUMBER

1002

.0625 .1249 1.5875 3.1725 l oo2·ooo·E/MXXXX·K

.1250- .1874 3.1750 - 4.7600 l oo2·oo1·E/MXXXX·K

.1 87 5- .2500 4.7625 6.3500 l O02·o02·E/MXXX X·K

2002

.0625 .1249 1.5875 3.1725 2oo2·ooo·E/MXXXX·K

.1250- .1 874 3.1 750 - 4.7600 2002·00 l ·E/MXXXX·K

.1875 .2499 4.7625 6.3475 2oo 2·oo 2·E/MXXXX·K

.2500- .3124 7.93 75 - 95250 2oo2·oo3·E/MXXXX·K

.3125 - .3750 6.3500 7. 9350 2oo2·oo4·E/MXXXX·K

3002

.1094 - .1249 2.77 88 3.1725 3oo2·2oo·E/MXXXX·K

.1250- .1 874 3.1750 - 4.7600 Jo02·oo1 ·E/MXXXX·K

.1875 - .2499 4.7625 - 6.3475 3002·o02·E/MXXXX·K

.2500 - .3124 6.3500 - 7.9350 Jo02·ooJ·E/MXXXX·K

.3125 - .3749 7.9375 9. 5225 Jo02·oo4·E/MXXXX·K

.3750 .4687 9.5250 11.9050 Jo02·oo5·E/MXXXX·K

.4688 .5000 11 .9075 12.7000 3oo2·oo6·E/MXXXX·K

4002

.1094 .1249 2.7788 3.1725 4002·ooo·E/MXXXX·K

.1250- .1874 3.1750 - 4.7600 4oo2·oo1 ·E/MXXXX·K

.1875 .2499 4.7625 - 6.3475 4oo2·oo2·E/MXXXX·K

.2500 .31 24 6.3500 7.9350 4oo2·oo3·E/MXXXX·K

.31 25 - .3749 7.9375 9.5225 4oo2·oo4·E/MXXXX·K

SERIES A·TOOL SIZE

INCHES A·TOOL SIZE

MM PART NUMBER

4002

.3750 .4687 9.5250 - 11.9050 4oo2·oo5·E/MXXXX·K

.4688 - .5624 11.9075 14.2850 4oo2·oo6·E/MXXXX·K

.5625 .6561 14.2875 16.6649 4oo2·oo7·E/MXXXX·K

.6562- .7500 16.6675 19.0500 4oo2·ooB·E/MXXXX·K

500 2

.2500 .3124 6.3500- 7.9350 5oo2·oo3·E/MXXXX·K

.3125- .3749 7.93 75 9.5225 5oo2·oo4·E/MXXXX·K

.3750 .4687 9.5250- 11 .9050 5oo2·oo5·E/MXXXX·K

.4688- .5624 11.9075 14.2850 5oo2·oo6·E/MXXXX·K

.5625 - 6561 14.2875 16.6649 5oo2·007·E/MXXXX·K

.6562 .7499 16.6675 - 19.0475 5oo2·ooB·E/MXXXX·K

.7500 .8749 19.0500 - 22.2225 5oo2·oo9·E/MXXXX·K

.8750 1.000" 22.2250 - 25.4000 5oo2·010·E/MXXXX·K

6002

.3750 .4687 9.5250·11 .9050 6oo2·oo5·E/MXXXX·K

.4688 .5624 11 .9075 14.2850 6oo2·oo6·E/MXXXX·K

.5625 - 6561 14.2875 -1 6.6649 6oo2·oo7·E/MXXXX·K

.6562 .7499 16.6675 19.0475 6oo2·0oB·E/MXXXX·K

6002·009·E/MXXXX·K .7500 .8749 19.0500·22.2225

.8750 9999 22.2250 25.3975 6oo2·010·E/MXXXX·K

1.0000 1.1 874 25.4000 30.1600 6oo2·o11 ·E/MXXXX·K

1.1875 1.3750 30.1625 - 34.9250 6002·o12·E/MXXXX·K

To order a complete tool holder assembly (with NOTES: 1. It is recommended that all tools have tang drives. collet) . you must have the following information: 1. Tool holder series 2. Pre-set screw size (see tables above using tool

size to determine part number) 3. Specify English (E) or Metric (M) 4. Tool Shank size for collet 1.0. (See page 7 for

proper collet ordering information). 5. Specify (K) if Thru-Coolant application is required . Example: _002 - 00_- __ -K

~ ~ ~ ~ ~

(1) (2) (3) (4) (5)

------------------------------------------------------------------------------------5 PHONE: 734·591·0134· FAX: 734·591·7866

FL-Tool Holders

Tapered Tool Holder Assembly without Collet

NOTE: Tool Holder assembly includes Body, Collet Nut, Tool Holder Seal, Tool Holder Snap Ring, Positive Drive and Pre-Set Screw Assembly.

Ordering Information

SERIES A·TOOL SIZE A·TOOL SIZE PART NUMBER

1002

.0625 .1249 1.5875 3.1725 1002·000

.1250 .1874 3.1750 - 4.7600 1002·001

.1 875 - .2500 4.7625 6.3500 1002·002

2002

.0625 - .1249 1.5875 3.1725 2002·000

.1250 .1 874 3.1750 - 4.7600 2002·001

.1875 .2499 4.7625 6.3475 2002·002

.2500 .3124 6.3500 7.9350 2002·003

.3125 .3750 7.9375 95250 2002·004

300 2

.1094 .1249 2. 7788 3.1725 3002·200

.1250 .1874 3.1750 4.7600 3002·001

.1875 .2499 4.7625 6.3475 3002·002

.2500 .31 24 6.3500 7.9350 3002·003

.3125 - .3749 7.9375 9.5225 3002·004

.3750 .4687 9.5250 11 .9050 3002·004

.4688 .5000 11.9075 12.7000 3002·006

4002

.1094 .1 249 2. 7788 3. 1725 4002·000

.1250 .1874 3. 1750 - 4.7600 4002·001

.1875 .2499 4.7625 6.3475 4002·002

.2500 .3124 6.3500 7.9350 4002·003

.3125 .3749 7.9375 9.5225 4002·004

SERIES A·TOOL SIZE A·TOOL SIZE PART NUMBER

4002

.3750 .4687 9.5250 11 .9050 4002 ·005

.4688 .5624 11 .9075 14.2850 4002·006

.5625 .6561 14.2875 16.6649 4002·007

.6562 .7500 16.6675 19.0500 4002·008

5002

.2500 .3124 6.3500 7.9350 5002·003

.3125 .3749 7.9375 9.5225 5002·004

.3750 .4687 9.5250 11 .9050 5002·005

.4688 .5624 11 .9075 14.2850 5002·006

.5625 6561 14.2875 16.6649 5002·007

.6562 .7499 16.6675 19.0475 5002·008

.7500 .8749 19.0500 22.2225 5002·009

.8750 1.000 " 22.2250 25.4000 5002·010

6002

.3750 .4687 9.5250·11 .9050 6002·005

.4688 .5624 11 .9075 14.2850 6002·006

.5625 6561 14.2875 - 16.6649 6002·007

.6562 .7499 16.6675 19.0475 6002·008

.7500 .8749 19.0500·22.222 5 6002·009

.8750 9999 22.2250 25.3975 6002·010

1.0000 1.1874 25.4000 30.1600 6002·011

1.1875 1.3750 30.1625 34.9250 6002·012

To order a complete tool holder assembly (without collet), you must have the following information: 1. Tool holder series 2. Positive drive size (see tables above using tool size to determine part number) Example: _002 - 00_

~ ~

(1) (2)

NOTES: 1. It is recommended that all tools have tang drives.

6-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI 48150


Tapered Tool Holder with Collet Nut

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

NOTE: Tool Holder includes Tool Holder Body, Tool Holder Seal, Tool Holder Snap Ring and Collet Nut.

SERIES PART NUMBER

1002 1002·BN

2002 2002·BN

3002 3002·BN

4002 4002·BN

5002 5002·BN

6002 6002·BN

Tapered Tool Holder Blank (Solid)

I NOTE: Tool Holder includes Tool Holder Seal and Snap Ring. These solid holders are to plug spindles when not being used.

BDIA.

~


SERIES PART NUMBER A B

1002 1002·BLANK 1.00 .62

2002 2002·BLANK 1.25 .88

3002 3002·BLANK 1.38 1.06

4002 4002·BLANK 1.38 1.56

5002 5002·BLANK 1.50 2.12

6002 6002·BLANK 1.50 2.50

------------------------------------------------------------------------------------ 7 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Tapered Tool Holder Components TOOL HOLDER SEAL

SPINDLE RETAINING RING (See page 11)

SPINDLE COLLAR COLLET(See page 8)(See page 11) SNAP RING

TOOL HOLDER BODY TOOL HOLDER (See page 9)(See page 8) SNAP RING

(See page 8) COLLET (See page 9)

POSITIVE DRIVE and PRE-SET SCREW

RUBBER WASHER COLLET NUT (Thru-coolant only) (See page 9)

ASSEMBLY (See page 10)

(See page II)

Quick-Change Tapered Body Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

GAGE DIA. r B

SERIES PART NUMBER A B C 0

1002 1002·B .6875 7/8 -12 1.005 2.27

2002 2002·B 1.000 11/4- 12 1.245 2.93

3002 3002·B 1.250 11/2-12 1.375 3.56

4002 4002·B '.

1.750 2 -12 1.375 4.16

5002 5002·B 2.250 21/2 - 12 1.685 5.03

6002 6002·B 2.750 3 -12 1.850 5.85

D

Tool Holder Seal and Snap Ring SERIES PART NUMBER

1000 1002·TS

2000 2002·TS

3000 3002·TS

4000 4002·TS

5000 5002·TS

6000 6002·TS

SERIES PART NUMBER

1000 1002·TSR

2000 2002·TSR

3000 3002·TSR

4000 4002·TSR

5000 5002·TSR

6000 6002·TSR Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed. NOTE: Snap rings are manufactured by

Spir%x Company.

8 -----------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Collet Nut ---. A .-

SPANNER NUTD.A.l.

SERIES PART NUMBER A B C 0

1002 1002·N .477 .87 9/16 28 3/4

2002 2002·N .571 1.23 13/16-12 11/16

3002 3002·N .644 1.44 1 - 12 11/4

4002 4002·N .696 2.02 11/2 - 12 1 3/4

5002 5002·N .840 2.50 2.0 -12 SPANNER

6002 6002·N .840 3.00 25/16-12 SPANNER

SERIES PART NUMBER

1002 1002·SR

2002 2002·SR

3002 3002·SR

4002 4002·SR

5002 5002·SR

6002 6002·SR

NOTE: Snap rings are manufactured by Tru-Arc Company.

SNAP RING REFERENCE

SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE B C

1002 1002·E/M (KI .0625 .2500 1.5875 6.3500 1.005 .4390

2002 2002·E/M (K) .0625 .3750 1.5875 9.5250 1.035 .5630

3002 J002·E/M (K) .1094 .5000 2.7788 12.7000 1.185 .7200

4002 4002·E/M (K) .1094 .7500 2.7788 19.0500 1.770 1.1310

5002 500H/M (K) .2500 1.0000 6.350 25.4000 2.200 1.4460

6002 6002·E/M (K) .3750 1.3750 9.5250 34.9250 2.700 1.9100

NOTE: These are precision collets, manufactured within ±.0001inch of specified tool shank size. FL-Tool Holders recommends a + .0000/ - .0005 tolerance on the tool shank to ensure maximum accuracy and clamping performance (up to - .0015 tolerance is acceptable if necessary.) Shank taper should no exceed .0002.

t B

MINIMUM CLEARANCE

DIAMETER

•+-0_ WRENCH

SIZE

Ordering Information 1. l.ocate desired Series number. 2. Order by Part Number listed.

Collet Snap Ring Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

Collets

(

GAGE DIAMETER

Ordering Information 1. Order by Part Number. 2. Specify English or Metric 3. To determine proper collet ID size, use the high

tolerance limit on the tool shank.

Example: A 4000 Series collet used with a .7500 +.0000/.0005 diameter tool shank requires collet Part Number 4002 - E7500.

Add 'K' at end of part number if Thru-Coolant is required (a rubber washer will be supplied).

A snap ring is supplied with each collet item ordered.

------------------------------------------------------------------------------------9 PHONE: 734·591·0134· FAX: 734·591·7866

FL-Tool Holders

Positive Drive and Pre-Set Screw Assembly Ordering Information B~ III( ..

1. Locate desired Series number. O.A.L. I 2 Use Tool Shank Size to determine HEX FOR --.. D '-.1

correct Part Number. ALLEN WRENCH T

NOTE: It is recommended that all tools have tang drives.

LEFT HAND THREAD

SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE A B C D E

1002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 5/64

1002 1002·1 .1250 - .1874 3.1750 - 4.7600 5/16 - 24 .31 .096 .18 5/64

1002·2 .1875 - .2500 4.7625 - 6.3500 .125 .18 5/64

2002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 7/64

2002·1 .1250- .1874 3.1750 - 4.7600 .096 .18 7/64

2002 2002·2 .1875 - .2499 4.7625 - 6.3475 7/16 - 20 .70 .125 .18 7/64

2002·3 .2500 - .3124 6.3500 - 7.9350 .172 .22 7/64

2002·4 .3125 - .3750 7.9375 - 9.5250 .213 .22 7/64

3002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 7/32

3002·1 .1250- .1874 3.1750 - 4.7600 .096 .18 7/32

3002·2 .1875 - .2499 4.7625 - 6.3475 .125 .18 7/32

3002 3002·3 .2500 - .3124 6.3500 - 7.9350 9/16 - 24 .80 .172 .22 7/32

3002·4 .3125 - .3749 7.9375 - 9.5225 .213 .25 7/32

3002·5 .3750 - .4687 9.5250 -11 .9050 .253 .25 7/32

3002·6 .4687 - .5000 119050 - 12.7000 .313 .25 7/32

4002·0 .1094- .1249 2.7788- 3.1725 NO SLOT 5/16

4002·1 .1250 - .1874 3.1750 - 4.7600 .096 .25 5/16

4002·2 .1875 - .2499 4.7625 - 6.3475 .125 .25 5/16

4002·3 .2500 - .3124 6.3500 - 7.9350 .172 . .31 5/16

4002 4002·4 .3125 - .3749 7.9375 - 9.5225 13/16 - 20 .85 .213 .31 5/16

4002·5 .3750 - .4687 9.5250 - 119050 .253 .31 5/16

4002·6 .4687 - .5624 119050 -14.2850 .313 .31 5/16

4002·7 .5625 - .6561 14.2875 - 16.6649 .383 .31 5/16

4002·8 .6562 - .7500 16.6675 - 19.0500 .453 .31 5/16

5002·3 .2500 - .3124 6.3500 -7.9350 .172 .31 7/16

5002·4 .3125 - .3749 7.9375 - 9.5225 .213 .31 7/16

5002·5 .3750 - .4687 9.5250 - 11 .9050 .253 .31 7/16

5002 5002·6 .4687 - .5624 119050 - 14.2850

1 1/8 -..20 1.00 .313 .31 7/16

5002·7 .5625 - 6561 14.2875 -16.6650 .383 .31 7/16

5002·8 .6562 - .7499 16.6675 - 19.0475 .453 .38 7/16

5002·9 .7500 - .8749 19.0500 - 22.2225 .524 .38 7/16

5002·10 .8750 - 1.000 22.2250 - 25.4000 .620 .38 7/16

6002·5 .3750 - .4687 9.5250 - 11.9050 .253 .31 1/2

6002·6 .4687 - .5624 11 .9050- 14.2850 .313 .31 1/2

6002·7 .5625 - .656 1 14.2875 - 16.6650 .383 .31 1/2

6002 6002·8 .6562 - .7499 16.6675 - 19.0475

11/2 - 2,0 1.25 .453 .38 1/2

6002·9 .7500 - .8749 19.0500 - 22.2225 .524 .38 1/2

6002·10 .8750 - .9999 22.2250 - 25.3975 .620 .38 1/2

6002·11 1.0000 -1.1874 25.4000 - 30.1600 .710 .44 1/2

6002·12 1.1875 - 1.3750 30.1625 - 34.9250 .827 .44 li2

1001 SERIES ONLY

TANG

--

.094 - .090

.122 -. 118

--

.094 - .090

.122 - .118

.162 - .158

.203 - .199

--

.094 - .090

.122 - .118

.162 - .158

.203 - .199

.243 - .239

.303 - .297

- -.094 - .090

.122- .118

.162 - .158

.203 - .199

.243 - .239

.303 - .297

.373 - .367

.443 - 4.37

.162- .158

.203- .199

.243 - .239

.303 - .297

.373 - .367

.443 - .437

.514 - .508

.609 - .601

.243 - .239

.303 - .297

.373 - .367

.443 - .437

.514 - .508

.609 - .601

.700 - .692

.817 - .809

10---------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Rubber Washer 10 Ordering Information 1. Locate desired Series number. 2. Use Tool Shank Size to determine

correct Part Number

PART TOOL SIZE TOOL SIZE SERIES PART TOOL SIZE TOOL SIZE

SERIES NUMBER INCHES MM NUMBER INCHES MM

1002·RWO .180·.200 4.57·5.08 5002·RWI .250·.260 6.35·6.60

1002·RWOA .201 ·.220 5.10·5.59 5002·RW2 .261·.300 6.63·7.62 1002

1002·RW1 .221·.240 5.61·6.10 5002·RW3 .301 ·.340 7.64·8.64

1002·RW1A .241·.250 6.12·6.35 5002·RW4 .341·.380 8.66·9.65

2002·RWO .180·.200 4.57·5.08 5002·RW5 .381 ·.420 9.68·10.67

2002·RWOA .201 ·.220 5.10·5.59 5002·RW6 .421·.460 10.69·11.68

2002·RW1 .221·.240 5.61 ·6.10 5002·RW7 .461·.500 11.71·12.70

2002·RW1A .241·.260 6.12·6.60 5002·RW8 .501 ·.540 12.72-13.72

2002·RW2 .261 ·.280 6.63·7.11 5002·RW9 .541 ·.580 13.74·1 4.73

2002 2002·RW2A .281 ·.300 7.14-7.62 5002 5002·RW10 .581 ·.620 14.75·15.75

2002·RW3 .301 ·.320 7.64·8.13 5002·RW11 .621·.660 15.77-16.76

2002·RW3A .32 1·.340 8.15·8.64 5002·RW12 .661 ·.700 16.79·17.78

2002·RW4 .341 ·.360 8.66·9.14 5002·RW13 .701-.740 17.80·18.80

2002·RW4A .361 ·370 9.17·9.40 5002·RW14 .741 ·.780 18.82·19.81

2002·RW5 .371 ·.375 9.42·9.53 5002·RW15 .781·.820 19.83·20.83

3002·RWO .180·.200 4.57·5.08 5002·RW16 .821 ·.860 20.85·21.84

3002·RWOA .201 ·.220 5.10·5.59 5002·RW17 .861 ·.900 21 .87·22.86

3002·RWI .221·.240 5.61 ·6.10 5002·RW18 .901·.940 22.88·23.88

3002·RWIA .241 ·.260 6.12·6.60 5002·RW19 .941·.980 23.90·24.89

3002·RW2 .261 ·.280 6.63·7.11 5002·RW20 .981·1.00 24.92·25.40

3002·RW2A .281·.300 7.14·7.62 6002·RW4 .375·.380 9.53·9.65

3002·RW3 .301·.320 7.64·8.13 6002·RW5 .381 ·.420 9.68·10.67

3002 3002·RW3A .321 ·.340 8.15·8.64 6002·RW6 .421·.460 10.69·11.68

3002·RW4 .341 ·.360 8.66·9.14 6002·RW7 .461·.500 11.71 ·12.70

3002·RW4A .361 ·.380 9.17·9.65 .6002·RW8 .501 ·.540 12.72- 13.72

3002·RW5 .381 ·.400 9.68·10.16 6002·RW9 .541 ·.580 13.74·14.73

3002·RW5A .401 ·.420 10.18·10.67 6002·RW10 .581 ·.620 14.75·15.75

3002·RW6 .421·.440 10.69·11.18 6002·RWll .621 ·.660 15.77- 16.76

3002·RW6A .441·.460 11 .20·11 .68 6002·RW12 .661 ·.700 16.79·17.78

3002·RW7 .461 ·.480 11.71·12.19 6002·RW13 .701 ·.740 17.80·18.80

3002·RW7A .481 ·.500 12.22·12.70 6002·RW14 .741 ·.780 18.82·19.81

4002·RWO .180·.220 4.57·5.59 6002·RW15 .781 ·.820 19.83-20.83

4002·RWI .221·.260 5.61 ·6.60 6002 6002·RW16 .821·.860 20.85·21.84

4002·RW2 .261 ·.300 6.63·7.62 6002·RW17 .861 ·.900 21.87·22.85

4002·RW3 .301·.340 7.64·8.64 6002·RW18 .901 ·.940 22.88·23.88

4002·RW4 .341 ·.380 8.66·9.65 6002·RW19 .941 ·.980 23.90·24.89

4002·RW5 .381 ·.420 9.68·10.67 6002·RW20 .981-1.020 24.92·25.91

4002·RW6 .421 ·.460 10.69·11.68 6002·RW21 1.021-1.060 25.93·26.92

4002 4002·RW7 .461 ·.500 11.71·12.70 6002·RW22 1.061 ·1.1 00 26.95·27.94

4002·RW8 .501·.540 12.72-13.72 6002·RW23 1. 101 ·1.140 27.96·28.96

4002·RW9 .541 ·.580 13.74·14.73 6002·RW24 1.141 ·1.180 28.98·29.97

4002·RW10 .581 ·.620 14.75·15.75 6002·RW25 1.1 81-1.220 30.00·30.99

4002·RW11 .621 ·.660 15.77-16.76 6002·RW26 1.221-1.260 31 .01 ·32.00

4002·RW12 .661 ·.700 16.79·17.78 6002·RW27 1.261·1.300 32.03-33.02

4002·RW13 .701 ·.740 17.80·18.80 6002·RW28 1.301-1.340 33.04·34.04

4002·RW14 .741 ·.750 18.82·1 9.05 6002·RW29 1.341-1.375 34.06·34.93

11

PHONE: 734-591-0134· FAX: 734-591-7866

Spindle Components TAPERED TOOL HOLDER

BLY


FL-Tool Holders

SERIES PART NUMBER

1002 1002·CR

2002 2002·CR

3002 3002·CR

4002 4002·CR

5002 5002·CR

6002 6002·CR

NOTE: Spindle components consist of a collar and retaining ring. They may be purchased Individually or as an assembly.

Spindle Collar and Retaining Ring SERIES PART NUMBER A

1002 1002·C 7/8 - 12

2002 2002·C 11/4 - 12

3002 3002·C 1 1/2 - 12

4002 4002·C 2 -1 2

5002 5002·C 2.5 -1 2

6002 6002·C 3 - 12 Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

Open End Spindle Wrench

I. A "I


SERIES PART NUMBER

1002 1002·R

2002 2002·R

3002 3002·R

4002 4002·R

5002 5002·R

6002 6002·R

SERIES PART NUMBER ADIM B DIM

100i . 100Z·WSP·S 10.00 .82

2002 ZOOZ·WSP·S 10.00 1.20

3002 300Z-WSP·S 12.00 1.44

4002 400Z·WSP·S 12.00 1.94

5002 5002·WSP·S 12.00 2.38

6002 600Z-WSP·S 12.00 2.86

NOTE: This wrench is used to retain the spindle when loosening or tightening the spindle collar if necessary.

Open End Spindle Collar Wrench


SERIES PART NUMBER A DIM B DIM

1002 100Z·WSP 8.00 1.16

2002 ZOO2·WSP 8.00 1.53

3002 300Z·WSP 9.50 1.78

4002 400Z-WSP 9.50 2.28

5002 500Z·WSP 9.50 2.62

6002 600Z·WSP 9.50 3.1 2

NOTE: It is recommended that this wrench be used to loosen or tighten the spindle collar.

12---------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Socket Spindle Collar Wrench

I B

~ Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed.

SERIES PART NUMBER ADIA. B LENGTH

1002 1002·W 1.50 4.00

2002 2002·W 1.88 4.50

3002 3DD2·W 2.12 4.50

4002 4D02·W 2.62 4.50

5002 5002·W 3.12 4.50

6002 6002·W 3.62 4.50


Holding Adapter for Tool Change


Spindle Cleaning Swab

Ordering Information I . Locate desired Series number. 2. Order by Part Number listed.

SERIES PART NUMBER A LENGTH B FLATS

1002 IOD2·A 1.62 1.25

2002 2D02·A 2.12 1.50

3002 3002·A 2.62 2.00

4002 4002·A 3.25 2.50

5002 5002·A 3.90 3.00

6002 6D02·A 4.50 3.50

NOTE: The holding adapter is designed to be used in a vise to loosen or tighten the collet nut. This prevents damage to the tool holder body.

SERIES PART NUMBER

1002 1002·S

2002 2002·S

3002 3002·S

4002 4002·S

5002 5002·S

6002 6002·S

NOTE: These cleaning swabs are designed for easy cleaning of the spindle taper.

------------------------------------------------------------------------------13 PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders

Tool Setting Fixture Assembly /

TAPERED TOOL HOLDER SERIES AS REQUIRED

GAGE LINE

Tool Setting Fixture


Screwdriver Adapter

Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed _ 3. Specify Screwdriver or Hex style.

Tool Setting Fixture

r TOOL SET

l/AGELINE

r CERTIFIED

DIM.

1 _ . - -_ . _ . _. _. - . - . _ . -. _.

GRANITE

j EPLATE

---.. CERTIFIED DIM.

SERIES PART NUMBER

1002 1002-RTF

2002 2002-RTF

3002 3002-RTF

4002 4002·RTF

5002 5002-RTF

6002 6002-RTF

NOTE: These holders have an ANSI 50V 0 _0. taper with Series required I.D.

SERIES PART NUMBER

1002 & 2002 1002 & 2002 - RTA

3002 & 4002 3002 & 4002 - RTA

5002 5002-RTA

6002 6002·RTA

NOTE: These spring loaded adapters are used with tool setting fixtures instead of a screwdriver or Allen wrench. Ends are replaceable .


SERIES PART NUMBER

1002 1002-TSF

2002 2002-TSF

3002 3002·TSF

4002 4002·TSF

5002 5002·TSF

6002 6002·TSF

This gage is designed to be used on a granite base plate with an indicator stand to set tool height.

14 ---------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Torque Wrench (3/8" Drive) Ordering Information 1. Order by Part Number.

Crowsfoot for Collet Nut Ordering Information 1. Locate desired Series number. 2. Order by Part Number listed .

SERIES

1002

2002

3002

4002

5002

6002

Snap Ring Pliers Ordering Information 1. Order by Part Number.

PART NUMBER PART NUMBER

752·1 752·1A

752·2 752·2A

752·3 752·3

752·4 752·4

N/A N/A

N/A N/A

PART NUMBER

752·MF

PART NUMBER A

N/A 3/4

N/A 11/16

N/A 11/4

N/A 13/4

752·5 2 1/2

752·6 3

XXXO & XXX1 SERIES USES A OCTAGON NUT XXX2 SERIES USES A HEX NUT *5000 & 6000 SERIES ARE SPANNER NUT ONLY

PART NUMBER

B52·SRP

_________________________________________________________________________________ 15

PHONE: 734-591-0134· FAX: 734-591-7866

Toolsetting Fixtures FL-Tool Holders manufactures and

stocks various kinds of toolsetting fixtures . Among the systems available are turret type , flange type, slide type, electronic and indicator. 50V tapered adapters, replaceable bushings and special applications can be designed and built to accommodate specific customer requirements.

FL-Tool Holders

16-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI48150

FL-Tool Holders'"

Straight Shank and Collet-Type Toolholders and Straight shank and collet-type tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design. Benefits of the systems include increased machining efficiency, high accuracy repeatability and quick-change ability.

Three different body sizes are available in each model to accommodate tools ranging from %4 (2.7788 mm) to %-inch (19.0500 mm) in diameter. Straight shank tool holders feature a guaranteed accuracy within 0.001 T.LR. runout 2-inches from the collet face. This is measured by a zero spindle and a class XX gage pin.

Each straight shank and collettype tool holder assembly includes a body, collet, collet nut and snap ring, tool holder seal and snap ring, positive drive and a preset screw assembly as well as a rubber washer and rear coolant seal for thru-coolant applications. OPERATION The close fit of the toolholder O.D. to the spindle LD. enables accurate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a clockwise direction to mate with the Acme left-hand thread on the toolholder body, retaining the holder intothespindle. Counterclockwise rotation of the collar forces the toolholder body out of the spindle.

Each patented toolholder series features an automotive straight shank and an LD. tapered collet seat that accurately locates the cutting tool centerline, and adjustable preset screw and drive assembly which pro-

vides tool height adjustment and positive drive to the tool. The compact design minimizes spindle-to-spindle center distance and overhang from the spindle end to the bearing journal diameters.

A complete line of optional accessories complements the straight shank holder and collet type toolholder. They include toolsetting fixtures, holding adapters for tool change, spindle cleaning swabs and spindle collar wrenches. FL:Tool Holders

Features and Benefits

• Increased Machining Efficiency

• High Accuracy Repeatability

• Quitk Changeability

• Thru-Coolant Capability

can provide full scale drawing templates or CAD disks for every product upon request.

2 ____________________________________________________________________________ __

Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters

Over-The-Spindle Adapter Assemblies

Over-the-spindle adapters transform standard high production machine spindles into quickchange adjustable tool adapters. They can be used with straight shank tool holders, automotive collet type tool holders or existing automotive shank toolholders by using a standard spindle collar and adapter nut assembly.

Located directly onto the spindle outside diameter and securely fastened with a locking set screw, the over-the-spindle adapter assemblies feature a left-hand threaded collar that forces an Acme left-hand threaded adapter nutto seat directly againstthe spindle face. This enables the spindle to take the thrust generated by the tool, eliminating any

Table of Contents Adapter Assemblies ........ .. ..... 4

Adapters ............ .... ..... .. ..... ... 5

Adapter Nut .... ...... .. ...... ....... . 5

Lockscrew ......... ...... .... ..... ..... 5

Toolholder Seal .. ... ..... ... ... .. .... 5

Toolholder Snap Ring .. .... ....... 5

Straight Shank Assembly .... ... . 6

Straight Shank Components .. 7

Straight Shank Body ..... .. .... ... 7

Collet-Type Assembly ......... .. .. 8

Collet-Type Components ... .. .. 9

Collet-Type Body .. ... ..... .. ....... 9

Collet .. ... .... .. .... .. .... .. ....... ... . 10

Collet Nut ...... ... ........ ... .... .... 10

Collet Snap Ring ... ... .. .. ..... ... 10

Rubber Washer ..... ... .... ........ 10

Positive Drive and Pre-Set Screw Assembly ........... .... 11

Rear Coolant Seals .. .... ... ..... . 11

Spindle Dimensions ..... ... ... ... 12

Socket Spindle Collar Wrench .... .... ... .. ....... .... .... 12

Open End Spindle Collar Wrench ..... ...... ......... .... ... . 12

thrust from being directed to the set screw.

When loosened, the mechanically activated over-the-spindle adapter (standard or stub model) forces chips away from the spindle face. Details are hardened and ground for consistent accuracy and are available to fit every machine builder'sstandard spindles.

____________________________________________________________________________ 3

FL-Tool Holders""

Over-The-Spindle Adapter Assembly

SPINDLE END

ADAPTER NUT

ADAPTER SIZE

-r--------· E

G SPINDLE TO

SPINDLE

C~~~ER SNAP RING DISTANCE FACE SEAL

-~- -- - -- -- - -- - - - --- - - -- - -- - - -- - -- - --- - -- - -- - - -- -Ordering Information 1. Locate desired adapter size. 2. Order by Part Number.

LOCKSCREW-NOTE: FOR RETAINING O.S.A. ONTO SPINDLE V4-28 UNF FOR 1;2 ADAPTERS 5116-24 UNF FOR REMAINING ADAPTERS -.. ~

O.S.A .

SLEEVE

+.000 - .002

F SPINDLE DIA.

SERIES ADAPTER SIZE

-lNCHES

10500 112

10625 &8

10750 314

10875 7Al

11000 1

11063 1-111 6

11375 1-3-8

11875 1-7Al

A SSEMBLY PART

NUMBER

10500AN

10625AN

10750AN

10875AN

11000AN

11063AN

11375AN

11875AN

NOTE: Assembly includes sleeve, collar, retaining ring assembly, adapter nut and lock screw, face seal and snap ring.

A B C D E F G

.64 1.250 .93 1.910 1.15 .735 1.25

.64 1.250 .96 1.910 1.40 .985 1.50

.64 1.250 1.01 1.910 1.65 1.235 1.75

.64 1.56 1.01 2.220 1.77 1.360 1.87

.64 1.56 1.01 2.220 1.90 1.484 2.00

.64 1.56 1.01 2.220 2.02 1.610 2.12

.64 1.810 1.01 2.470 2.40 1.985 2.50

.75 2.31 0 1.10 3.090 3.02 2.610 3.1 2

Over-The-Spindle Adapter Assembly IL--_------' (Stub Model)

SPINDLE END ~

ADAPTER NUT\

ADAPTER SIZE

-r ---- ----D DIA.-

LOCKSCREW-NOTE: FOR RETAINING O.S.A. ONTO SPINDLE 516-24UNF

G SPINDLE TO

SPINDLE MIN.

CENTER ADAPTER ASSEMBLY DISTANCE

-~-- - - - -- -- - - - - -- - - --- - --- - - - - - - - - - -- - - - - -- - - - - - SERIES

Ordering Information 10750

1. Locate desired adapter size. 2. Order by Part Number. 10875

11000

11063

11375

11875

ADAPTER SIZE

-lNCHES

314

7Al

1

1-1116

1-3-8

1-7Al

NOTE: Assembly includes sleeve, collar, retaining ring assembly, adapter nut and lock screw, face seal and snap ring.

ASSEMBLY A B C D E F PART

NUMBER

10750SAN .64 1.01 1.20 1.65 1.235 1.75

10875SAN .64 1.01 1.20 1.77 1.360 1.87

11000SAN .64 1.01 1.20 1.90 1.484 2.00

11063SAN .64 1.01 1.20 2.02 1.610 2.1 2

11375SAN .64 1.01 1.20 2.40 1.985 2.50

11875SAN .75 1.10 1.20 3.02 2.610 3.12

4 ________________________________________________________________________ _


Over-The-Spindle Adapter SERIES SIZE PART NUMBER INCHES

10500 112 l0500A

10625 &8 10625A

10750 :¥4 10750A

10875 718 10875A

11000 1 11000A

11063 1-111 6 11063A

Ordering Information 11375 1-3-8 11375A

11875 1-718 11875A 1. locate desired adapter size. 2. Order by Part Number.

Over-The-Spindle Adapter L-I ______ ---'

(Stub Model) SERIES SIZE PART NUMBER

INCHES

10750 :¥4 10750SA

10875 718 l0875SA

11000 1 11000sA

11063 1-111 6 11063SA

Ordering Information 11375 1-3-8 11375SA

1. locate desired adapter size. 11875 1-718 11875SA 2. Order by Part Number.

Adapter Nut and Lockscrew ,--I _____ _ SERIES SIZE PART NUMBER SERIES SIZE PART NUMBER

INCHES INCHES

10500 112 10500N 10500 112 l0500L

10625 &8 10625N 10625 &8 l0625L

10750 :¥4 10750N 10750 :¥4 10750L

10875 718 10875N 10875 718 10875L

11000 1 ll000N 11000 1 11000L

11063 1-111 6 11063N 11063 1-1116 11063L

Ordering Information 11375 1-3-8 11375N Ordering Information 11375 1-3-8 11375L

11875 1-718 11875N 1. locate desired adapter size. 2. Order by Part Number.

11875 1-718 11875L 1. locate desired adapter size. 2. Order by Part Number.

Toolholder Seal and Snap Ring ,-I _ ___ ----'

SERIES PART NUMBER

10750 107~TS

Ordering Information 11063 11063-TS

11375 4002-TS 1. locate desired Series number 2. Order by Part Number listed

SERIES

10750

Ordering Information 11063

11375 1. locate desired Series number 2. Order by Part Number listed

PART NUMBER

3002-TSR

4002-TSR

4002-TSR

NOTE: Snap rings are manufactured by Spir%x Company.

______________________________________________________________________________ 5

FL-Tool Holders'"

Straight Shank Toolholder Assembly

t

SERIES A B HOLDER TOOL SIZE TOOL SIZE SHANK -INCHES ~

10750 314 .0625-.4375 1.5875-11 .1120

11063 1-1116 .1094-.7500 2.7788-19.0500

11375 1-3-8 .1094-.7500 2.7788-19.0500

SERIES TOOL SIZE TOOL SIZE PART NUMBER -INCHES ~

.0625-.1249 1.5875--3.1725 10750-SS-000

.1250-.1874 3.1750-4.7600 1 0750-5S-001

.1875-.2499 4 .7625~.3475 10750-5S-002 10750

.2500-.3124 6.3500-7.9350 10750-55-003

.3125-.3749 7.9375-9.5225 10750-55-004

.3750-.4375 9.5250-11 .1120 10750-S5-o05

.1094-.1249 2.7788--3.1725 11063-55-000 11375-S5-o00

.1250-.1874 3.1750-4.7600 11063-SS-001 11375-SS-001

.1875- .2499 4 .7625~.3475 11063-55-002 11375-55-002

.2500-.3124 6.3500-7.9350 11063-S5-o03

11063 11375-SS-003

OR .3125-.3749 7.9375-9.5225 11 063-5S-004 11375-5S-004

11375 11063-55-005 .3750-.4687 9.5250-11 .9050

11375-5S-005

.4688-.5624 11 .9075-14.2850 11 063-5S-006 11375-55-006

.5625-.6561 14.2875-16.6649 11063-S5-007 11375-S5-007

.6562-.7500 16.6675-19.0500 11063-S5-o08 11375-5S-008

F

C D

MIN.

1.65 1.75 1.50

2 .00 2.18 2.30

1.70 1.88 2.30

NOTE: Toolholder assembly includes body, collet, collet nut, snap ring, positive drive, pre-set screw assembly, face seal and snap ring. For thru-coolant applications a rear coolant seal and rubber washer are required.

E F G

MAX.

3.62 1.44 112--32

5.24 2.02 13'16- 20

4.80 2.02 13'16-20

Ordering Information (With Collet) To order a complete toolholder assembly (with collet), you must have the following information: 1. Series to be used, 2. Positive drive size (see tables above using tool size to determine Part Number). 3. Specify English (E) or Metric (M). 4. Tool shank size for collet I.D.-4 place decimal. (See page 8 for collet ordering information.) 5. Specify K if thru-coolant application is required.

EXAMPLE: -55-00 - - -K

-~- -~-~-~ ~

(1) (2)(3) (4) (5)

Ordering Information (Without Collet) To order a complete tool holder assembly (without collet), you must have the following information: 1. Series to be used. 2. Positive drive size (see tables above using tool size to determine Part Number).

EXAMPLE: _---, __ -55-00

~ (1)

~ (2)

NOTE: Tang drives are recommended for all tools.

6 ________________________________________________________________________ _


Individual Components SPINDLE (Page 12)

LOCK SCREW (Page 5)

OVER-THESPINDLE ADAPTER (Page 5)

POSITIVE DRIVE & PRE-SET SCREW

ASSEMBLY (Page 11 )

NOTE: Toolholder assembly is retained in the spindle by a FL-Tool Holders QuickChange over-the-spindle adapter. NOTE: All straight shank components are interchangeable with tapered toolholders except for the positive drive and set screw assembly for Part Number 10750. NOTE: For Thru-coolant applications, a rubber washer (page 10) and rear coolant seal (page 11) are required.

STRAIGHT SHANK TOOLHOLDER

(This page)

TOOLHOLDER COLLET SNAP RING (Page 10)

(Page 5)

TOOLHOLDER RUBBER WASHER SEAL - THRU-COOLANT

(Page 5) ONLY (Page 10)

COLLET SNAP RING

(Page 10)

COLLET NUT

(Page 10)

Straight Shank Toolholder BO~Y II-___ _

E DIA.

~-------- A---------.j

1----- B ---.j

D- ACME THREAD (LEFT HAND) ~ C-ACME THREAD

SERIES SHANK A B C 0 SIZE PART

~NCHES NUMBER

Ordering Information 10750 314 1075~558 4.00 1.50 1-124G 1-3-8-12 1. Locate desired Series Number. 2. Order by Part Number.

11063 1-1116 11063-558 4.92 1.80 l -V2- 124G 1-314-12

11375 1-3-8 11375-558 5.52 1.50 1-V2-124G 2- 12

E

.75001.7499

1.0626/1 .0625

1.3751 /1.3750

_________________________________________________________________________ 7

FL-Tool Holders™

Collet Type Toolholder Assembly

E ~---- TOOL SET RANGE -----,~

COOLANT PLUG MAX. DIM .)

G

SERIES A-TOOL SIZE B-TOOLSIZE B-TOOLSIZE

~NCHES ~NCHES -MM

10750 314 .0625-.4375 1.5875-1 1.1120

11063 1-V16 .1094-.7500 2.7788-19.0500

11375 1-36 .1094- .7500 2.7788-1 9.0500

SERIES TOOL SIZE TOOL SIZE PART NUMBER ~NCHES -MM

.0625-.1249 1.5875-3.1725 107SD-OH-OOO

.1250-.1874 3.1750--4.7600 1075D-OH-D01

.1875-.2499 4 .7625~.3475 1075D-OH-D02 10750

.2500-.3124 6.3500-7.9350 1075D-OH-003

.3125-.3749 7.9375-9.5225 107SD-OH-004

.3750-.4375 9.5250-11.1120 1075D-OH-DOS

.1094-.1249 2.7788-3.1725 11063-0H-OOO 11375-0H-OOO

.1250-.1874 3.1750--4.7600 1',~-_ --.11

11375-0H-D01

.1875-.2499 4.7625~.3475 1',_y-_ ~ .• _

11375-0H-D02

.2500-.3124 6.3500-7.9350 11063-0H-003

11063 11375-0H-003

OR .3125-.3749 7.9375-9.5225 11063-0H-004 11375-0H-004

11375 .3750-.4687 9.5250-11 .9050 11063-0H-005 11375-0H-005

.4688-.5624 11 .9075-14.2850 11063-DH-D06 11375-0H-D06

.5625-.6561 14.2875-16.6649 111 7 11375-0H-D07

.6562-.7500 16.6675-19.0500 11063-DH-008 11375-0H-008

F

C 0 E MAX.

1.68 1.78 1.50 3.70

2.06 2.24 2.30 4.56

1.68 1.86 2.30 5.20

NOTE: Toolholder assembly includes body, collet, collet nut, snap ring, positive drive pre-set screw assembly, adjuster nut, face seal and snap ring. For thru-coolant applications a rear coolant seal and rubber washer are required.

F G

1.44 112-32

2.02 13116-20

2.02 13116-20

Ordering Information (With Collet) To order a complete toolholder assembly (with collet), you must have the following information: 1. Series to be used. 2. Positive drive size (see tables above using tool size to determine Part Number). 3. Specify English (E) or Metric (M). 4. Tool shank size for collet I.D.-4 place decimal. (See page 8 for collet ordering information.) 5. Specify K if thru-coolant application is required .

EXAMPLE: -DH-OO _ - _ - __ -K

~ ~ ~ ~ ~ (1) (2) (3) (4) (5)

Ordering Information (Without Collet) To order a complete toolholder assembly (without collet), you must have the following information: 1. Series to be used. 2. Positive drive size (see tables above using tool size to determine Part Number) .

EXAMPLE: ___ -DH-OO

~ ~ (1) (2)


8 ____________________________________________________________________________ __


Individual Components SPINDLE (Page 12)

OVER-THESPINDLE ADAPTER ( 5)

TOOLHOLDER SNAP RING

(Page 5)

ADAPTER NUT (Page 5)

LOCK SCREW (Page 5)

TOOLHOLDER POSITIVE DRIVE & SEAL PRE-SET SCREW

(Page 5) ASSEMBLY

NOTE: Toolholder assembly is retained in the spindle by a FL-Tool Holders Quick-Change over-the-spindle adapter. NOTE: All straight shank components are interchangeable with tapered toolholders except for the positive drive and set screw assembly for Part Number 10750. NOTE: For Thru-coolant applications, a rubber washer (page 10) and rear coolant seal (page 11) are required.

(Page 11)

STRAIGHT SHANK TOOLHOLDER

(This page)

COLLET (Page 10)

RUBBER WASHER - THRU-COOLANT

ONLY (Page 10)

COLLET SNAP RING

(Page 10)

COLLET NUT

(Page 10)

Collet Type Toolholder Body IL--_ ___ ---'

D-ACME THREAD (LEFT HAND) ~ ~ C- ACME THREAD

SHANK PART SERIES SIZE- NUMBER A B C 0 INCHES

10750 314 10750-DHB 3.81 1.00 1- 124G 314-12

Ordering Information 11063 1-1 /16 11063-DHB 4.88 1.38 1-1;2-124G 1-1/1 6- 12

1. locate desired Series Number. 2. Order by Part Number. 11375 1-3-8 11375-DHB 5.38 1.00 1-1;2-124G 1-3-8--12

_________________________________________________________________________ 9

Collet

Ordering Information 1. Order by Part Number. 2. Specify English (E) or Metric (M) .

C

TOOL SIZE RANGE

FL-Tool Holders'"

o SNAP RING

REFERENCE

3. Determine proper collet I.D. size, use the high limit on the tool shank. 4. Add K at end of Part Number if thrucoolant is required (a rubber washer will be supplied).

GAGE DIAMETER

NOTE: These are precision collets manufactured within ±.0001 inch of specified tool shank size. FL-Tool Holders recommends a +.0000/-.0005 inch tolerance on tool shank to ensure maximum accuracy and clamping performance (up to -.0015 inch tolerance is acceptable if necessary). Shank taper should not exceed .0002 inch.

EXAMPLE: Series 11375 collet used with a .7500 +.0000/-.0005 diameter tool shank requires collet part number 4000-El500.

A snap ring is supplied with each collet item ordered.

SERIES

10750

11063 or 11375

PART NUMBER A·TOOLSIZE -INCHES

3002--£IM (I<) .1094-.5000

4002--£IM (I<) .1094-.7500

A·TOOLSIZE B C -MM

2.7788-12.7000 1.185 .7200

2.7788-19.0500 1.770 1. 1310

Collet Nut and Snap Ring L..-I ______ ----'

1 O.~Lr

C THREAD SIZE

SERIES

10750

11063 or 11375

PART NUMBER

3002-N

4002-N

D WRENCH

SIZE / I

/\ A B C 0

.644 1.44 1- 12 1·V4

.696 2.02 1·112-12 1':314

+ B

MINIMUM CLEARANCE DIAMETER

t

Ordering Information 1. Locate desired Series Number. 2. Order by Part Number.

o --

SERIES PART NUMBER

10750 3002-5R

11063 or 11375 4002-5R

RubberVVasher~1 ____________________ ~

o PART NUMBER A·TOOLSIZE A·TOOLSIZE -INCHES -MM

~ .180-.220 4.57-5.60

RW-1 .220-.260 5 .6~.60

PART NUMBER A·TOOLSIZE A·TOOLSIZE -INCHES -MM

RW~ .500-.540 12.70-13.70

RW---e .540-.580 13.70-14.70

Ordering Information ~ .260-.300 6.60-7.60 RW-10 .580- .620 14.70-15.70

1. Locate desired Series Number. ~ .300-.340 7 .6Q-8.60 RW-11 .620-.660 15.70- 16.80

RW-4 .340-.380 8.60-9.60 2. Use Tool Shank size to determine Part Number.

RW-12 .660-.700 16.80-17.80

SERIES PART NUMBER RW-6 .380- .420 9.60- 10.60 RW-13 .700-.740 17.80-18.80

10750 3002-RW_ RW-6 .420-.460 10.60-11 .70 RW-14 .740-.780 18.80-19.80

11063 or 11375 4002-RW_ RW-7 .460-.500 11 .70-12.70

10 __________________________________________________________________________ __


Positive Drive and Pre-Set Screw Assembly E

HEX FOR ALLEN WRENCH

Ordering Information 1. Locate desired Series Number. 2. Use Tool Shank size to determine Part Number.

SERIES

10750

11063

OR

11375

SCREW DRIVER SLOT REF.

A-TOOL SIZE PART NUMBER -INCHES

1075G-O .0625-.1249

10750-1 .1250- .1874

10750-2 .1875-.2499

10750-3 .2500-.3124

10750-4 .3125-.3749

10750-5 .3750-.4375

4OO2---{) .0625- .1249

4002-1 .1250-.1874

4002-2 .1875-.2499

4002-3 .2500-.3124

4002-4 .3125-.3749

4002-5 .3750- .4686

4oo2~ .4687-.5624

4002-7 .5625-.6561

4002-8 .6562-.7500

r~~ ~

A LEFT HAND THREAD

A-TOOL SIZE A -NM

1.5875-3.1725

3.1750-4.7600

4 .7625~ .3475

112-32 6.3500-7.9350

7 .9375-9.5250

9.5250-11 .1120

1.5875-3.1725

3.1750-4.7600

4 .7625~.3475

6.3500-7.9350

7.9375-9.5225 13'16- 20

9.5250- 12.4104

12.4130-14.2850

14.2875-16.6649

16.6675-19.0500


B C 0 E TANG WIDTH REFERENCE

NO SLOT 3'16 - --

.096 .18 3'16 .094- .090

.125 .18 3'16 .122- .118 .70

.172 .22 3'16 .162- .158

.213 .22 3'16 .203-.199

.253 .25 3'16 .243-.239

NO SLOT 5116 ---

.096 .25 5116 .094- .090

.125 .25 5116 .122- .118

.172 .31 5116 .162- .158

.88 .213 .31 5116 .203- .199

.253 .31 5116 .243-.239

.313 .31 5116 .303- .297

.383 .31 5116 .373-.367

.453 .31 5116 .443- .437

Rear Coolant Seals L--I _________ ----'

o COOLANT

HOLE

Ordering Information

C

1. Locate desired Series Number. 2. Use Tool Shank size to determine Part Number.

ORING GROOVE REF.

A PLUG 0 .0.

B SPINDLE 1.0.

t SERIES PART ±O.OO5 A +0.002 C 0

NUMBER ~.OOOB

10750 10750-RCS .740 .750 1/2-32 .31

11063 11063-RCS .740 .750 13/16- 20 .50

11375 11375-RCS .990 1.000 13/16-20 .50

Note: a ring supplied with plugs

11

FL-Tool Holders'"

FACE MUST BE SQUARE --,--_

M WITH BORE WITHIN 0.0002 T.I.R. 90. Recommended Spindle Dimensions

L* P DRILL G ~\ ~~K~~ 30.l

~I

NOTE: Diameters marked with an asterisk (*) must be concentric within. ODDS T.I.R.

SERIES .. IUNI03 .. 0.005 +0.005 -G.OOOO A -G.OOO B -G.OOO C

10750 .7503 .162 .830

11063 1.0629 .193 1.158

11375 1.3754 .256 1.499

.. 0.000 -G.DOS D

1.250

1.562

1.812

- A* E -- - --

~dJ

(Long O.S.A.) 1------- H

J

E +0.000 G H J -G.002 F

.81 1.235 2.50 2.62 3.62

1.12 1.610 3.12 3.25 4.25

1.44 1.985 4.12 4.25 5.25

K .. 0.002 M -G.OOO L

.81 .750 .78

1.12 .750 .78

1.44 1.000 1.03

.. 0.000 P -G.OOS N

.500 .250

.500 .312

.500 .375

Socket Spindle Collar Wrench 1'----------' A


B ·1


SERIES PART NUMBER

10500 l0500-W

10625 l0625-W

10750 1075G-W

10875 10875-W

11000 11~W

11063 11063-W

11375 11375-W

11875 11875-W

A B DIAMETER LENGTH

1.38 4.00

1.62 4.50

1.88 4.50

2.00 4.50

2.12 4.50

2.23 4.50

2.62 4.50

3.25 4.50

Open End Spindle Collar Wrench L--I _ __ ---'

~ B

j

11+-------... - A~J SERIES PART NUMBER A B

DIM. DIM.

10750 2002-WSP 7.81 1.54

11063 l1063-WSP 8.62 1.91

11375 4002-WSP 8.62 2.28



A Member of the Air Gage Family of Companies One Step Ahead in Quality Control

36010 Industrial Road Livonia, Michigan 48150 Telephone 313/591-0134 FAX 313-591-7866

12 ________________________________________________________________________ __ AGC-311/94 LITHO IN USA

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 48150

Phone: 734-591-0134· Fax: 734-591-7866 www.fltoolholders.com

3/4" STRAIGHT SHANK TOOL HOLDERS WITH ER 16 COLLET NUT SYSTEM

• Increased Machining Efficiency • High Accuracy Repeatability

• Quick Changeability • Thru Coolant Capability

• Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design, Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange ability,

The 3/4" body size will accommodate tools ranging from 1/16" (1 ,588 mm) to 7/16" (11 ,112 mm) in diameter, Straight shank tool holders feature a guaranteed accuracy within 0,0001 T,I.R, runout two inches from the collet face, This is measured by a zero spindle and a class XX gage pin ,

The close fit of the tool holder 0.0, to the spindle I. D, enables accurate and secure positioning of the over-the-spindle adapter collar , Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face, This eliminates the rocking condition seen is short taper designs, Counterclockwise rotation of the collar forces the tool holder body out of the spindle ,

Each patented tool holder assembly features a straight shank with an 1.0, tapered collet seat that accurately locates the cutting tool centerline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool. A sealed collet and rear coolant seal for thru-coolant applications are available, ,The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters,

STRAIGHT SHANK TOOL HOLDER WITH ER 16 COLLET NUT SYSTEM

AOAPTER ASSEMBLY STANDARD PT.# 107S0-A STUB PT# 10750-SA

-.--- -----

+ .000 -.002 1.235 DIA. SPINDLE REF.

SHANK DIAMETER

314

LOCKSCREW 5/16-24 UNF PT.# 10750-L INCLUDED IN ASS'Y

TOOL SHANK RANGE

.0625-.1249

.1250-.1874

.1875-.2499

.2500-.3124

.3125-.3749

.3750-.4375

1.60 MIN. 3.20 MAX.

f---- 1.91 (STANDARD)

~ 1.20

(STUB)

r 1.01 REF.

-----f-NOTE: SUBTRACT .50 ON THE MAX. toOL AOJUSTMENT IF A COOLANT PLUG 'is USED.

1.10 DIA.RET.

_~SPINDLE ~ END REF.

1.25 1.80 (STANDARD)

ASSEMBLY ORDERING OPTIONS ASSEMBLY ASSEMBLY

ASSEMBL Y WITH

WITH COLLET LESS COLLET BODY & COLLET

NUT

10750·ER·000·EIMXXXX 10750·ER·000

10750·ER·001 ·EIMXXXX 1 0750·ER·00 1

10750·ER·002·EIMXXXX 10750·ER·002 10750·ERBN

10750·ER·003·EIMXXXX 10750·ER·003

10750·ER·004·EIMXXXX 10750·ER·004

10750·ER·005·EIMXXXX 10750·ER·005

OSA

10750·A (STANDARD)

OR 10750·SA

(STUB)

INDIVIDUAL COMPONENT ORDERING OPTIONS SHANK TOOL SHANK

POSITIVE DRIVE TOOL HOLDER

COLLET NUT OSA DIAMETER RANGE BODY

.0625-. 1249 10750·0

.1250-.1874 10750·1 10750·A

.1875-.2499 10750·2 (STANDARD) 314 10750·ERB SA·20·5A OR

.2500-.3124 10750·3 10750·SA

.3125-.3749 10750·4 (STUB)

.3750-.4375 10750·5

REAR COOLANT SEAL

10750·RCS

REAR COOLANT SEAL

10750·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

FL-TOOL HOLDERS 3601 0 Industrial Road • Livonia, Michigan 481 50


1 3/8" STRAIGHT SHANK TOOL HOLDERS WITH ER 32 COLLET NUT SYSTEM



• Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design. Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange ability.

The 1 3/8" body size will accommodate tools ranging from 7/64" (2.778 mm) to 3/4" (19.05 mm) in diameter. Straight shank tool holders feature a guaranteed accuracy within 0.0001 T.I .R. runout two inches from the collet face. This is measured by a zero spindle and a class XX gage pin .

The close fit of the tool holder 0.0 . to the spindle I. D. enables accurate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face . This eliminates the rocking condition seen is short taper designs. Counterclockwise rotation of the coliar forces the tool holder body out of the spindle .

Eac h patented tool holder assembly features a straight shank with an 1.0. tapered collet seat that accurately locates the c utting tool centerline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool. A sealed col let and rear coolant seal for thru-coolant applications are available .

. The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters.


ADAP TER ASSEMBL Y STANDARD PT.# l1J 75-A STUB PT# l 1J75-SA

+.000 -. 002· 1.985 DIA. SPINDLE REF.

2. 12 MIN. 4.70 MAX.

-- 2.47 (STANDARD)

-----t-NOTE; SUBTRACT .50 ON THE MAX. TOOL ADJUSTMEN T IF A COOLA NT PLUG IS USED.

.38 REF.

1.97 DIA.REF.

-L--_ - - - - - - -:s~===~~t:5r-E::::: +----'-

SHANK DIAMETER

1·3/8

LOCKSCREW 5/16-24 UNF PT.# 1I 375~L INCLUDED IN ASS'Y

TOOL SHANK RANGE

.1094-.1249

.1250-.1874

.1875-.2499

.2500-.3124

.3125- .3749

.3750- .4687

.4688-.5624

.5625-.6561

.6562-.7500


1.810 1.75 (STANDARD)

ASSEMBLY ORDERING OPTIONS

ASSEMBLY ASSEMBLY ASSEMBLY WITH

BODY & WITH COLLET LESS COLLET

COLLET NUT

11375·ER·000·E/MXXXX 11375·ER·000

11375·ER·00 l·E/MXXXX 11375·ER·00 1

11375·ER·002·E/MXXXX 11375·ER·002

11375·ER·003·E/MXXXX 11375·ER·003

11375·ER·00H/MXXXX 11375·ER·004 11375·ERBN

11375·ER·005·E/MXXXX 11375·ER·005

11375·ER·006·E/MXXXX 11375·ER·006

11375·ER·007 ·E/MXXXX 11375·ER·007

11375·ER·008·E/MXXXX 11375·ER·008

OSA

11375·A (STANDARD)

OR 11375·SA

(STUB)




.1094- .1249 4002·0

.1250 - .1874 4002·1

.1875-.2499 4002·2 11375·A

.2500- .3124 4002·3 (STANDARD) 1·3/8 .3125- .3749 4002-4 11375·ERB SA·32·5A OR

.3750-.4687 4002·5 11375·SA (STUB)

.4688- .5624 4002·6

.5625-.6561 4002·7

.6562-.7500 4002·8

REAR COOLANT SEAL

11375·RCS

REAR COOLANT SEAL

11375·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs , Cad disk available upon request.


Phone: 734-591 -0134 · Fax: 734-591-7866 www.fltoolholders.com

1 1/16" STRAIGHT SHANK TOOL HOLDERS WITH ER 32 COLLET NUT SYSTEM



• Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regard less of orig inal manufacturer, into a quick-change design. Benefits of the system include increased machining efficiency, high accuracy repeatabi lity and quickchange ability.

The 1 1/l 6" body size wi ll accommodate tools ranging from 7/64" (2 .788 mm) to 3/4" (19.05 mm) in diameter . Straight shank tool holders feature a guaranteed accurac y within 0.000 1 T.I.R. runout two inches from the collet face . This is measured by a zero spindle and a c lass XX gage pin .

The close fit of the tool holder 0.0 . to the spindle I. D. enables accurate and secure positioning of the over-the-spindle adapter collar. Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face. This e liminates the rocking condition seen is short taper designs. Counterc lockwise rotation of the collar forces the tool holder body out of the spindle.

Each patented tool holder assembly features a stra ight shank with an 1.0. tapered collet seat that accurately locates the c utting tool centerline and an adjustable preset screw and drive assembly whic h provides tool height adjustment and positive drive to the tool. A sealed collet and rear coolant seal for thru-coolant applications are avai lable . The compact design minim izes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters.


ADAPT[R ASS[MBLY STANDARD PT. # 11063- A STUB PT# II 063-SA

+ .000 -.002 . I .6 10DIA SPINDL[ R[F.

SHANK DIAMETER

1·1/16

LOCKSCR[W 5/16 - 2 4 UNF PT.# 11 063 - L INCLUDED IN ASS'Y

TOOL SHANK RANGE

.1094-.1249

.1250 -.1874

.1875-.2499

.2500- .3124

.3125-.3749

.3750- .4687

.4688-.5624

.5625-.6561

.6562-.7500

2. 12 MIN. 3.70 MA X.

f--- 2.22 (STANDARD)

----t-NOT[: SUBTRA CT .50 ON TH[ MAX. TOOL ADJUSTM[NT IF A COOLANT PLUG IS USED.

~ 1. 20

(STUB)

r 1.01 RET

.38 R[F.

_~SPINDL[ ~ [NO R[F ..

1. 56 1.75 (S TANDARD)

.2362 MIN. _

. 7500 MAX. TOOL RANG[


ASSEMBLY ASSEMBLY ASSEMBLY WITH

BODY & WITH COLLET LESS COLLET

COLLET NUT

11063·ER·000·E/MXXXX 11063·ER·000

11063·ER·001 ·E/MXXXX 11063·ER·001

11063·ER·002·E/MXXXX 11063·ER·002

oSA

11063·A 11063·ER·003·E/MXXXX 11063·ER·003 (STANDARD) 11063·ER·004·E/MXXXX 11063·ER·004 11063·ERBN OR

11063·ER·005·E/MXXXX 11063·ER·005 11063-SA (STUB)

11063·ER·006·E/MXXXX 11063·ER·006

11063·ER·007·E/MXXXX 11063·ER·007

11063·ER·008·E/MXXXX 11063·ER·008



COLLET NUT oSA DIAMETER RANGE BODY

.1094-.1249 4002·0

.1250 -. 1874 4002·1

.1875-.2499 4002·2

.2500- .3124 4002·3 11063·A

(STANDARO) 1·1/16 .3125-.3749 4002·4 11063·ERB SA·32·5A OR

11063·SA .3750-.4687 4002·5 (STUB)

.4688-.5624 4002·6

.5625- .6561 4002·7

.6562-.7500 4002·8

REAR COOLANT SEAL

11063·RCS

REAR COOLANT SEAL

11063·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs. Cad disk available upon request.


Phone: 734-591-0134· Fax: 734-591-7866 'N'NW. fltoolholders. com

1 1/1 6" STRAIGHT SHANK TOOL HOLDERS WITH ER 16 COLLET NUT SYSTEM



• Patented

Straight shank tool holders can be used in existing automotive spindles with over-the-spindle adapters to transform any spindle, regardless of original manufacturer, into a quick-change design , Benefits of the system include increased machining efficiency, high accuracy repeatability and quickchange abil ity,

The 1 1/16" body size will accommodate tools ranging from 7/64" (2.788 mm) to 3/8" (9 ,525 mm) in diameter, Straight shank tool holders feature a guaranteed accuracy within 0,0001 T,I.R , runout two inches from the collet face, This is measured by a zero spindle and a class XX gage pin,

The close fit of the tool holder 0.0, to the spindle I. D, enables accurate and secure positioning of the over-the-spindle adapter collar , Mounted over an existing spindle, the collar is rotated in a

Clockwise direction to mate with the Acme lefthand thread on the tool holder body, retaining the holder securely against the spindle face , This eliminates the rocking condition seen is short taper designs, Counterclockwise rotation of the collar forces the tool holder body out of the spindle,

Each patented tool holder assembly features a straight shank with an 1.0, tapered collet seat that accurately locates the cutting tool centerline and an adjustable preset screw and drive assembly which provides tool height adjustment and positive drive to the tool , A sealed collet and rear coolant seal for thru-coolant applications are available , The compact design minimizes spindle to spindle center distance and overhang from the spindle end to the bearing journal diameters,


ADAPTER ASSEMBLY STANDARD prj 11 063- A STUB P T# 11 063-SA

-,---- - ----

+ .000 -. 002 1.610 DIA . SPINDLE REF.

1.60 MIN. 3.80 MAX.

1---- 2.22 (STANDARD)

1.20 (STUB)

- 1.0 1 REF.

----t-NOTf: SUBTRACT .50 ON THE MAX. TOOL ADJUSTMENT IF A COOLANT PLUG IS USED.

.38 REF.

--L..---_ ___ _ _ _ ~===~~

SHANK DIAMETER

1·1/16

LOCKSCREW 5/ 16- 24 UNF prj 11063 - L INCLUDED IN ASS'Y

TOOL SHANK RANGE

.1094-.1249

.1250 -.1874

.1875-.2499

.2500-.3124

.3125-.3750


1.56 - - --- 1.80 (STANDARD)


ASSEMBLY ASSEMBLY ASSEMBt. Y WITH

BOOY & WITH COLLET LESS COLLET

COLLET NUT

11063·ER·000·E/MXXXX 11063·ER·000

11 063·ER·00 l ·E/MXXXX 11063·ER·001

11063·ER·002·E/MXXXX 11063·ER·002 11063·ERBN

11063·ER·003·E/MXXXX 11063·ER·003

11063·ER·00H/MXXXX 11063·ER·004

OSA

11063·A (STANDARD)

OR 11063·SA

(STUB)




.1094- .1249 4002·0 11063·A

.1250-.1874 4002·1 (STANDARD) 1·1/16 .1875-.2499 4002·2 11063·ERB SA·32·5A OR

.2500-.3124 4002·3 11063·SA

(STUB) .3125-.3750 4002·4

4.000 mm MIN. 9.525 mm MA X. TOOL RANGE

REAR COOLANT SEAL

11063·RCS

REAR COOLANT SEAL

11063·RCS

Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately) Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately) Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet) Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

FL-Yap and Reamer Holders Increase Positioning Accuracy to Improve Quality

FL floating tool holders are designed and built to compensate for misalignment between the spindle and work piece on previous drilled holes.

Our standard holders feature various styles of shanks including acme threaded, straight, Morse taper and Cat "V". Special designs can also be manufactured to satisfy your spindle requirements.

Our standard 'line of tap reamer holding components include tap adapters,SA collets, tap collets, reamer collets, Morse taper and dedicated size. Each component within our holders is engineered and manufactured to ensure maximum wear and durability.

Features and Benefits

• Automatically compensates for misalignment

• Armorclad surface coating for corrosion resistance

• Coolant thru available • Close Center distance • Adjustable tension and self

centering • Collet system and quick

change • Specials and custom design

available • Repair Facility on premises

FL-Tool Holders

I Table of Contents I TAR Series Quick Change Non-Floating Acme Shank Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 3

TAR Series Quick Change Non-Floating Straight Shank Tap Holders - - - - - - - - - - - - - - - - - - - Page 3

TAR Series Quick Change Non-Floating Morse Taper Shank Tap Holders - - - - - - - - - - - - - - - Page 4

TATC Series Quick Change Non-Floating Straight Shank Tension and Compression Tap Holders - -Page 4

TM Series Quick Change Radial Floating Acme Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5

TAS Series Quick Change Radial Floating Straight Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5

TAM Series Quick Change Radial Floating Morse Taper Shank Tap Holders - - - - - - - - - - - - - - - - - Page 6

T ATC Series Quick Change Radial Floating Acme Shank Tension-Compression Tap Holders - - - Page 7

TATC Series Quick Change Radial Floating Straight Shank Tension-Compression Tap Holders - - - - Page 8

THA Series Quick Change Radial Floating Acme Shank Tap Holders (Standard) - - - - - - - - - - - Page 9

THS Series Quick Change Radial Floating Straight Shank Tap Holders ( Standard) - - - - - - - - - - - -Page 9

THJ Series Quick Change Radial Floating Jacobs Shank Tap Holders ( Standard) - - - - - - - - - - - Page 10

CAT Series Quick Change Radial Floating Cat "V" Flange Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 10

TA & TAP Series Quick Change Fixed Length Tap Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 11

TSA Series Quick Change Collet Type Tap Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12

TAEA Series Quick Change Tap Adapters Axial Length Adjustment-Extended - - - - - - - - - - - - - Page 14

DSA Series Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders - - - -- - - - - Pages 15-20

SM Series Collet Type Radial Floating Acme Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 21

SM Series Collet Type Radial Floating Straight Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 22

SAC Series Collet Type Radial Floating Cat "V" Flange Reamer Holders - - - - - - - - - - - - - - - - Page 22

SA 16 Series Single Angle Collets - - - - - - - - - Page 23

SA 20 Series Single Angle Collets - - - - - - - - - . Page 23

SA 25 Series Single Angle Collets - - - - - - - - - - Page 24

SA 32 Series Single Angle Collets - - - - - - - - - Page 24

SAX Series Tap Collets with Internal Square Drive-Page 25

SA Series Single Angle Collet Accuracy and Installation and Removal Diagram - - - - - - - Page 26

TCA Series Collet Type Radial Floating Acme Shank Tap and Reamer Holders - - - - - - - - - - - - Page 27

TCA Series Collet Type Radial Floating Straight Shank Tap and Reamer Holders - - - - - - - - - - - Page 28

TC Series Tap Collets - - - - - - - - - - - - - - - - - - Page 29

TC Series Reamer Collet - - - - - - - - - - - - - - - - Page 29

MTA Series Morse Taper Radial Floating Acme Shank Tap and Reamer Holders A, B - - - - - - Page 30

MTB Series Morse Taper Radial Floating Acme Shank Tap and Reamer Holders - - - - - - - - - - Page 30

MTA Series Morse Taper Radial Floating Acme TC Series Quick Change Torque Adapters - - Page 12 Shank Tap and Reamer Holders C - - - - - - - - Page 31

TALA Series Quick Change Tap Adapters Axial FL Series Adjustable Acme Nuts - - - - - - - - - Page 31 Length Adjustment - - - - - - - - - - - - - - - - - - - Page 13

------------------------------------------------------------------------2 PHONE: 734-591-0134 • FAX: 734-591-7866 36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

Quick Change Non-Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and

Holder size in table.

2. Order by Part Number shown.

PART NUMBER HOLDER

SIZE

TAR·0·7001 0

TAR·0·7002

TAR·l ·7005 TAR·l ·7006 1 TAR· l ·7009

TAR·2·7013 2

TAR·2·7014

TAR·3·7018 3

TAP A L SIZES DIAMETER LENGTH

0101/4 0.875 1.890

010 1/2 1.250 2.043

5/16107/8 1.970 2.913

13/16101 3/8 2.835 3.993

Quick Change Non-Floating Straight Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and

Holder size in table. rLnt, r-

I 2. Order by Part Number shown.

PART NUMBER

TAR·0·7055 TAR·0·7056

TAR·l ·7057 TAR·l·7058

TAR·2·7060 TAR·2·7061

TAR·3·7062

HOLDER SIZE

0

1

2

3

-I

'-- /

A

~I -~---- D ------~I u TAP A L

SIZES DIAMETER LENGTH

0101/4 0.875 1.450

010 1/2 1.250 1.650

5/16107/8 1.970 2.475

13/161013/8 2.835 3.555

FL-Tool Holders

See Pages 11-14 For Tap Adapters

D

3.00

3.00 3.00 3.625

3.625 4.625

4.625


D

4.00

4.00 5.00

5.00

SHANK

5/8·16 3/4·12

5/8·16 3/4·12

11/16·12

11/16·12 1 3/8·12

13/8·12

SHANK

1/2 3/4

3/4 1

1 1 1/2

2

3---------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Floating Tap and Reamer

Quick Change Non-Floating Morse Taper Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and



PART NUMBER

TAR·0·7021 TAR·0·7022

TAR·l ·7031 TAR·l·7032 TAR·l·7033

TAR·2·7042 TAR·2·7043 TAR·2·7044

TAR·3·7053 TAR·3·7054

HOLDER TAP SIZE SIZES

#0 o to 1/4

#1 o to 1/2

#2 5/16 to 7/8

#3 13/16 to 1 3/8

A L DIAMETER LENGTH

0.875 1.575 1.637

1.730 1.250 1.793

1.793

2.663 1.980 2.663

2.723

2.835 3.743 3.805


MORSE TAPER SHANK

lMT 2MT

1MT 2MT 3MT

2MT 3MT 4MT

3MT 4MT

Quick Change Non-Floating Straight Shank Tension and Compression Tap Holders

ORDERING INFORMATION 1. Locate desired Tap and



PART NUMBER

TATC·1-70lO

TATC·2·7071

TATC·l · 7072

TATC·2·7073

TATC·3·7074

HOLDER SIZE

#1

#2

#1

#2

#3

~r------ A --------~

Fie T COMPRESSION TENSION

cC3m_~~t A D E B F

3.15 1.42 0.75 0.75 1.57

4.06 2.18 1.22 0.75 1.57

3.58 1.42 0.75 1.00 2.01

4.49 2.16 1.22 1.00 2.01

6.50 3.07 2.36 1.50 3.00


COMPENSATION Ten. Compo

0.30 0.30

0.49 0.49

0.30 0.30

0.49 0.49

0.79 0.79

------_______________________________________________________________________ 4

PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Radial Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and

Holder size in table .


1= MtN. "I g:----::-----~ [J()~~r ;

PART NUMBER HOLDER TAP

FLOAT A L SIZE SIZES DIAMETER LENGTH

TAA·O·7101 0 o to 1/4 .010 .875 2.448

TAA·0·7102

TAA·l ·7105 TAA·l ·7106 TAA·l ·7107 1 o to 1/2 .020 1.250 2.730 TAA·l ·7108 TAA·l ·7109

TAA·2·7111 TAA·2·7112

2 5/16 to 7/8 .040 1.980 3.863 TAA·2·7113 TAA·2·7114

TAA·3·7118 3 13/16 to 1 318 .060 2.835

5.343 TAA·3·7119 5.530

Quick Change Radial Floating Straight Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and


2. Order by Part Number shown .

PART NUMBER HOLDER

SIZE

TAS·0·7161 0

TAS·l·7170 1

TAS·l·7171

TAS·2·7181 2

TAS·2·7184

TAS·3·7192 3

TAS·3·7194

I" L .. ,

~'--------if [I]~~r i ~D-~" I

TAP FLOAT

A L SIZES DIAMETER LENGTH

o to 1/4 .010 0.875 2.011

o to 1/2 .020 1.250 2.293

5/16 to 7/8 .040 1.980 3.426

13/16 to 1 318 .060 2.835 4.906


0 SHANK

3.000 5/8·16 3/4·12

3.000 5/8·16 3.000 3/4·12 3.625 7/8·12 3.625 1·12 3.625 11/16·12

3.625 7/8·12 3.625 1·12 3.625 1 1/16·12 4.625 13/8·12

4.625 13/8·12 5.625 1 7/8·12


0 SHANK

4.00 3/4

4.00 3/4 1

4.00 1 5.00 11/2

5.00 11/2

2

5-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Quick Change Radial Floating Morse Taper Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap and



E( __ _

PART NUMBER HOLDER TAP

SIZE SIZES

TAM·O·7121 0 o to 1/4

TAM·0·7122

TAM·l ·7131 TAM·l·7132 1 o to 1/2 TAM·l ·7133

TAM·2·7142 TAM·2·7143 2 5/16 to 7/8 TAM·2·7144

TAM·3·7153 3 13/16 to 1 3/8

TAM·3·7154

A

FLOAT A L

DIAMETER LENGTH

.0lD .875 2.136 2.199

2.418 .020 1.250 2.481

2.481

3.613 .040 1.980 3.613

3.671

.060 2.835 5.093 5.156

\

See Pages 11 -14 For Tap Adapters

MORSE TAPER SHANK

lMT 2MT

lMT 2MT 3MT

2MT 3MT 4MT

3MT 4MT

FL-Tool Holders Offers a Complete Line of Complementary Products

Tapered Sha~k Tool Holders Straight Shank Tool Holders

Hydraulic Chucks Gun Drill and Reamer Holders

Spindles and Tool Setting Accessories

------------------------------------------------------------------6 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

Quick Change Radial Floating Acme Shank (Tension-Compression) Tap Holders ORDERING INFORMATION 1. Locate desired Tap and



HOLDER PART NUMBER

SIZE TAC·l ·7205 TAC·1·7206 TAC·1·7207 TAC·1·7208 TAC·1·7209 TAC·1·7210 TAC·1·7211 TAC·1·7212 TAC·l·7213 TAC·1·7214 TAC·1·7215 TAC·l ·7216 TAC·1·7217 1 TAC·1·7218 TAC·1·7219

TATC·l · 7220 TATC·1·7221 TATC·l ·7222 TATC·l ·7223 TATC·l ·7224 TAT·l·7225 TAT·l·7226 TAT·1·7227 TAT·1·7228 TAT·1·7229 TAC·2·7230 TAC·2·7231 TAC·2·7232 TAC·2·7233 TAC·2·7234 TAC·2·7235 TAC·2·7236 TAC·2·7237 TATC·2·7238 TATC·2·7239

2 TATC·2·7240 TATC 2·7241 TATC·2·7242 TATC·2·7243 TATC·2·7244 TATC·2·7245 TAT·2·7246 TAT·2·7247 TAT·2·7248 TAT·2·7250

L II---------- MIN ---------1

[[--~~ :--:BJ - I ]~-. --»--~~ A

TAP FLOAT

A C T L SHANK SIZES DIAMETER COMPo TENSION LENGTH 5/8·16 3/4·12

1.170 - 6.782 7/8·12 1·12

11/16·12 5/8·16 3/4·12

1.560 - 6.980 7/8·12 1·12

11/16·12 5/8·16 3/4·12

o to 1/2 .020 1.375 1.166 0.396 6.587 7/8·12 1·12

11/16·12 5/8·16 3/4·12

0.781 0.781 6.200 7/8·12 1·12

1 1/16·12 5/8·16 3/4·12

- 1.562 5.420 7/8·12 1·12

11/16·12 7/8·12

1.090 7.853 1·12 -

11/16 · 12 13/8·12 7/8·12

1.560 8.098 1·12 -

11/16·12 13/8·12 7/8·12

5/16 to 7/8 .040 1.980 1.1116 0.396 7.704 1·12

11/16·12 13/8·12 7/8·12

0.781 0.781 7.319 1·12 11/16·12 13/8·12 7/8·12

1.562 6.538 1·12 -

11/16·12 13/8·12

7------------------------------__________________________________________________ _ 36010 INDUSTRIAL ROAD. LIVONIA, MI48150


Quick Change Radial Floating Straight Shank (Tension-Compression) Tap Holders ORDERING INFORMATION 1. Locate desired Tap and


2. Order by Part Number

L

shown.

11-.-------- MIN -----------4-1

-++----1 EJ _. ~~------L-A See Pages 11-14 ~<-------t.:------j+----*L~~~~~_---.J~I-' _---' , For Tap Adapters

PART NUMBER HOLOER TAP

FLOAT A C T L

SHANK SIZE SIZES OIAMETER COMPo TENSION LENGTH

TAC·l ·7261 3/4 TAC-l ·7262 1.170 - 6.345 1 TAC·l ·7263 11/4

TAC·l·7264 3/4 TAC·l ·7265 1.560 - 6.543 1 TAC·l·7266 1 1/4

TATC·l·7267 3/4 TATC-1-7268 1 o to 1/2 .020 1.250 1.166 0.396 6.150 1 TATC-l·7269 1 1/4

TATC·l ·7270 3/4 TATC·l·7271 0.781 0.781 5.763 1 TATC·l ·7272 11/4

TAT-1-7273 3/4 TAT-' ·7274 - 1.562 4.983 1 TAT-1-7275 1 1/4

TAC·2·7276 1 TAC-2-7277 1.090 - 7.416 1.1/4 TAC-2·7278 11/2

TAC-2·7279 1 TAC·2-7280 1.560 - 7.661 1 1/4 TAC·2·7281 1 1/2

TATC·2·7282 1 TATC·2-7283 2 5/16 to 7/8 .040 1.980 0.166 0.396 7.267 11/4 TATC-2·7284 1 1/2

TATC·2·7285 1 TATC·2·7286 0.781 0.781 6.882 1 1/4 TATC·2-7287 1 1/2

TAT·2·7288 1 TAT·2·7289 - 1.562 6.100 11/4 TAT:2-7290 1 1/2

-----------------------------------------------------------------------------8 PHONE: 734·591·0134 • FAX: 734·591·7866

FL Tool Holders

Quick Change Radial Floating Acme Shank Tap Holders (Standard) ORDERING INFORMATION 1. Locate desired Shank and



#0 & #1 Holder size take #1 size Tap Adapters

TAP PART SIZE NUMBER

THA·0·7301 THA·0·7302 THA·0·7303

Tap THA·0·7304

Range THA·0·7305

0·9/16 THA·l ·7308 THA·l ·7309 THA·l· 7310 THA·l ·7311

I'

~----~--~--~--=--=---=--C=---~--=--~-HR-

02S0~ E 1----- - D , -

HOLDER B C

SIZE A

5/8·16

#0 3/4·12

1.500 1·12

1 1/16·12 13/8·12 1.187

3/4·12 #1 1/12

1.81 2 1 1/16·12 13/8·1 2

D

3.000 3.000 3.625 3.625 4.625

3.000 3.625 3.625 4.625

F

1.400

See Pages 11 -14 For Tap Adapters

N

3.14

Quick Change Radial Floating Straight Shank Tap Holders (Standard)

ORDERING INFORMATION 1. Locate desired Shank and



#0 & #1 Holder size take #1 size Tap Adapters


THS·0·7401 THS·0·7402

Tap THS·0·7403 Range 0·9/16 THS·l ·7404

THS·l·7405 THS·l ·7406

OP T IONAL COOLANT SE AL

HOLDER SIZE A

#0 1.500

#1 1.812

I.

B C

3/4 1

1 1/2 1.187

3/4 1 1

D F

4.000 1.406


N

2.47

9---------------------------------------------------------------------------------36010 INDUSTRIAL ROAD • LIVONIA, MI 48150


Quick Change Radial Floating Jacobs Shank Tap Holders (Standard) ORDERING INFORMATION 1. Locate desired Jacobs Taper

and Holder size in table.



THJ-1-9400 THJ-2-9401 THJ-3-9402

Tap THJ-33-9404 Range 0-9/16 THJ-1-9410

THJ-2-9411 THJ-3-9412 THJ -33-9414

r-\" DI A. SHANK

~

--Jo\COBS T~ -SIZ( • ..-I --

A -

r-

~ I'

I· N-"h .984

L , --t---.I. c .1. c~ HOLDER SIZE JACOB

C 0 A TAPER

#1 #1 #2

1_500 #3 #33

1.187 4_00 #1

#2 #2 1.812 #3

#33

Quick Change Radial Floating Cat V Flange Tap Holders ORDERING INFORMATION 1. Locate desired V Flange and



ADAPTER PART SERIES NUMBER

#1 CAT-40-1 0-9/16 CAT-50-1

#2 CAT-40-2 0-7/8 CAT-50-2

"S"- V CAT FL ANGE

RETfNTlON KNOBS AVAILABL E UPON REOUES T

HOLDER B

SIZE A

#1 40 1.812 50

#2 40 2.750 50

C E

1.187

1_00

1.502

PHONE: 734-591-0134 • FAX: 734-591-7866

F


N

1.406

2.593

2.200

F

1.175 1_375

2.125 1.125


N

3_87

5_37

10

FL-Tool Holders

Quick Change Fixed Length Tap Adapters ORDERING INFORMATION 1. Locate desired Tap

and Adapter size in table.

2a. Order by Part Number shown for Tang Drive.

2b. Add (-b) to end of Part Number

ADAPTER TAP PART NUMBER

SIZE SIZES

TA·l·6 0·6 TA·l·8 8 TA·l ·l0 10 TA·l ·12 12 TA·l·l/4 14 & 1/4 TA·l·5/16

1 5/16

TA·l ·7/16 7/16 TA·l ·l/2 1/2 TA·l ·3/8 3/8 TA·l ·9/16 9/16

TA·2·5/16 5/16 TA·2·7/16 7/16 TA·2·1/2 1/2 TA·2·3/8 3/8 TA·2·9/16

2 9/16

TA·2·5/8 5/8 TA·2·11/16 11/16 TA·2·3/4 3/4 TA·2·13/16 13/16 TA·2·7/8 7/8

TA·3·13/16 13/16 TA·3·7/8 7/8 TA·3·15/16 15/16 TA·3·1 3 1 TA·3·1·1/8 1 1/8 TA·3·1·1/4 11/4 TA·3·1·3/8 13/8

PART NUMBER ADAPTER TAP

SIZE SIZES

TAP·l ·l/8 SSP 1

1/8 SSP TAp·l ·l/8 LSP 1/8 LSP

TAp·2·1/8 NPT 1/8 NPT TAp·2·1/4 NPT 2 1/4 NPT TAp·2·1/2 NPT 1/2 NPT

TAp·3·1/4 NPT 1/2 NPT TAp·3·1/2 NPT

3 3/8 NPT

TAp·3·3/8 NPT 3/4 NPT TAp·3·3/4 NPT 1 NPT

11

TANG DRIVE

BALL DRIVE

SHANK

.141

.168

.194

.220

.255

.318

.323

.367

.381

.429

.318

.323

.367

.381

.429

.480

.542

.590

.652

.697

.652

.697

.760

.800

.896 1.021 1.108

SHANK

.3125

.4375

.4375

.5625

.6875

.6875

.7000

.9063 1.125

L~--r-=it f

~~ ~ 11-*++----+-'"1" j I ~c-~----'-

SQUARE A B

DIA. DIA.

.110

.131

.152

.165

.191 .73 1.18

.238

.242

.275

.286

.322

.238

.242

.275

.286

.322 1.18 1.90

.360

.406

.442

.489

.523

.489

.523

.570

.600 1.75 2.75

.672

.766

.831

SQUARE A , B

DIA. DIA.

.234 .73 1.18

.32~

.328

.421 1.18 1.90

.515

.515

.531 1.75 2.75

.812

36010 INDUSTRIAL ROAD. LIVONIA, MI48150

Available in Tang Drive or Ball Drive

D C L DIA. LENGTH LENGTH

.85

.92

.92

.95

.747 .270 .95 .98

1.08 1.11 1.05 1.17

1.49 1.59 1.62 1.56

1.219 .310 1.68 1.74 1.81 1.87 1.87 1.93

2.42 2.48 2.48

1.889 .405 2.54 2.61 2.73 2.79

D C L DIA. LENGTH LENGTH

.747 .270 1.05 1.05

1.05 1.219 .310 1.18

1.37

1.41

1.889 .405 1.32 1.55 1.68


Quick Change Collet Type Tap Adapters ORDERING INFORMATION 1. Locate desired Collet series

and Adapter size in table .


PART NUMBER ADAPTER SIZE

TSA·16 #1

TSA-25 #2

TSA-32 #3

r A

L

COLLET SERIES

16

25

32

IT c

TAP RANGE A

(mm.) (in.)

#0·6 - 1/2 19 0.75

#0-6 - 3/4 31 1.22

#0-6 - 15/16 48 1.89

Quick Change Torque Adapters ORDERING INFORMATION 1. Locate desired Tap

and Adapter size in table.


A SIZE #1 SIZE #2 TAP SIZE PART # PART #

0 - 6 TC-1 -6 TC-2-6

#8 TC-1-8 TC-2-8

#10 TC-l-l0 TC-2-10

#12 TC-1 -12 TC-2-12

1/4 TC-1 -1 /4 TC-2-1/4

5/16 TC-1-5/16 TC-2-5/16

3/8 TC-1-3/8 TC -2-3/8

7/16 TC -1-7/16 TC-2-7/16

A SIZE #1 SIZE#2 A TAP SIZE PART# PART # TAP SIZE

1/2 TC -1-1/2 TC-2-1/2 1/8 LSP

9/16 TC -1-9/16 TC-2-9/16 1/4 NPT

5/8 TC-2-5/8 3/8 NPT

11/16 TC-2-11/16

3/4 TC -2-3/4

13{1 6 TC-2-13/16

7/8 TC-2-7/8

B C (mm.) (in.) (mm.) (in.)

25 0.98 28 1.10

34 1.34 42 1.65

48 1.89 50 1.97

PIPE TAP

SIZE #1 SIZE #2 PART # PART #

TP-2-1/8 LSP TP-2-1/8 LSP

TP-2-1/4 NPT

TP-2-3/8 NPT

--------------------------------------------------------------------------------12 PHONE: 734-591-0134. FAX: 734-591-7866

Quick Change Tap Adapters Axial Length Adjustment ORDERING INFORMATION 1. Locate desired Tap and

Adapter size in table.


2b. Add (-b) to end of Part Number for Ball Drive.

PART NUMBER ADAPTER

SIZE

TALA·l·6 TALA·l·8 TALA·l ·1 0 TALA·l·12 TALA·l ·1/4

1 TALA·l·5/16 TALA·l·7/16 TALA·l·1/2 TALA·l ·3/8 TALA·l·9116

TALA·2·5/16 TALA·2·7/16 TALA·2·1/2 TALA·2·3/8 TALA·2·9/16

2 TALA·2·5/8 TALA·2·11116 TALA·2·3/4 TALA·2·13/16 TALA·2·7/8

TALA·3·5/8 TALA·3·11/16 TALA·3·3/4 T ALA·3·13/16 TALA·3·7/8

3 TALA·3·15/16 TALA·3·1 TALA·3·1·1/8 TALA·3·1 1/4 TALA·3·1 3/8

TALA·2·1/8 SSP 1

TALA·2·1/8 LSP

TALA·2·1/8 NPT TALA·2·1/4 NPT

2 TALA·2·1/2 NPT TALA·2·3/8 NPT

TALA·3·1/4 NPT TALA·3·1/2 NPT TALA·3·3/8 NPT 3 TALA·3·3/4 NPT TALA·3·1 NPT

BALL DRIVE

TAP SIZES

0·6 8 10 12

14 & 1/4 5/16 7/16 1/2 3/8 9/16

5/16 7/16 1/2 3/8 9/16 5/8

11/16 3/4

13/16 7/8

5/8 11/16 3/4

13/16 7/8

15/16 1

11/8 11/4 13/8

1/8 SSP 1/8LSP

1/8 NPT 1/4 NPT 1/2 NPT 3/8 NPT

1/4 NPT 1/2 NPT 3/8 NPT 3/4 NPT

1 NPT

I--- c

SHANK SQUARE A B

DlA. DlA.

.141 .110

.168 .131

.194 .152

.220 .1 65

.255 .191 .74 1.18

.318 .238

.323 .242

.367 .275

.381 .286

.429 .322

.318 .238'

.323 .242

.367 .275

.381 .286

.429 .322 1.18 1.90

.480 .360

.542 .406

.590 .442

.652 .489

.697 .523

.480 .360

.542 .460

.590 .442

.652 .489

.697 .523 1.88 2.75

.760 .570

.800 .600

.896 .672 1.021 .766 1.1 08 .831

.3125 .234 .74 1.18

.4375 . 3~8

.4375 .328

.5625 .421 1.18 1.90

.6875 .515

.7000 .531

.5620 .421

.6875 .515

.7000 .531 1.88 2.75

.9063 .812 1.125 .843

FL-Tool Holders


D ADUST C L DlA. LENGTH LENGTH LENGTH

.75

.82

.82

.85

.747 .394 1.28 .85 .96

1.05 1.08 1.02 1.15

1.03 1.12 1.15 1.09

1.219 .610 2.24 1.22 1.68 1.74 1.81 1.81 1.87

1.56 2.10 2.16 2.17

1.889 .980 2.98 2.23 2.23 2.30 2.36 2.48 2.55

.747 .394 1.28 1.02 1.02

1.08

1.219 .610 2.24 1.19 1.37 1.25

1.21 1.41

1.889 .980 2.98 1.27 1.46 1.58

13--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Quick Change Tap Adapters Axial Length Adjustment-Extended ORDERING INFORMATION 1. Locate desired Tap and

Adapter size in table.


2b. Add (-b) to end of Part Number for Ball Drive. BALL

DRIVE

PART NUMBER ADAPTER TAP

SIZE SIZES

TAEA·l·6 0·6 TAEA·l ·8 8 TAEA·l·l0 10 TAEA·l· 12 12 TAEA·l·1/4

1 14 & 1/4

TAEA·l·5/16 5/16 TAEA·l·7/16 7/16 TAEA·l ·1 /2 1/2 TAEA·l ·3/8 3/8 TAEA·l·9/16 9/16

TAEA·2·5/16 5/16 TAEA·2·7/16 7/16 TAEA·2·1/2 1/2 TAEA·2·3/8 3/8 TAEA·2·9/16

2 9/16

TAEA·2·5/8 5/8 TAEA·2·11/16 11/16 TAEA·2·3/4 3/4 TAEA·2·13/16 13/16 TAEA·2·7/8 7/8

TAEA·3·5/8 5/8 TAEA·3·1 1/16 11/16 TAEA·J.3/4 3/4 TAEA·3·13/16 13/16 TAEA·3·7/8

3 7/8

TAEA·3·15/16 15/16 TAEA·3·1 1 TAEA·3·1 1/8 11/8 TAEA·3·1 1/4 11/4 TAEA·J.l 3/8 13/8

TAEA·l·1/8 SSP 1

1/8 SSP TAEA·l· 1/8 LSP 1/8 LSP

TAEA·2·1/8 NPT 1/8 NPT TAEA·2·1/4 NPT

2 1/4 NPT

TAEA·2·1/2 NPT 1/2 NPT TAEA·2·3/8 NPT 3/8 NPT

TAEA·3·1/4 NPT 1/4 NPT TAEA·3·1/2 NPT 1/2 NPT TAEA·J.3/8 NPT 3 3/8 NPT TAEA·J.3/4 NPT 3/4 NPT TAEA·3·1 NPT 1 NPT

",", ___ I_.~L ~ __ ---.

__ -- ----=l-r t '" /1 SHANK A B

'F't---'lJ:)If--A_I.C.,--~ -----.J- -=r~ t .1. · ·


I-----C ADJUSTMENT

SHANK SQUARE A B D ADJUST C L

DlA. DlA. DIA. LENGTH LENGTH LENGTH

.141 .1 10 .75

.1 68 .1 31 .82

.194 .152 .82

.220 .165 .85

.255 .191 .74 1.18 .747 .394

.85 .318 .238 .96 .323 .242 1.05 .367 .275 1.08 .381 .286 1.02 .429 .322 1.15

.318 .238 1.03

.323 .242 1.12

.367 .275 1.15

.381 .286 1.09

.429 .322 1.18 1.90 1.219 .610

1.22 .480 .360 1.68 .542 .406 1.74 .590 .442 1.81 .652 .489 1.81 .697 .523 1.87

.480 .360 1.56

.542 .460 2.10

.590 .442 2.16

.652 .489 2.17

.697 .523 1.88 2.75 1.889 .980

2.23 .760 .570 2.23 .800 .600 2.30 .896 .672 2.36 1.021 .766 2.48 1.108 .831 2.55

.3125 .234 .74 1.18 .747 .394 1.28

1.02 .4375 .328 1.02

.4375 .328 1.08

.5625 .421 1.18 1.90 1.219 .610 2.24

1.19 .6875 .515 1.37 .7000 .531 1.25

.5620 .421 1.21

.6875 .515 1.41

.7000 .531 1.88 2.75 1.889 .980 2.98 1.27

.9063 .812 1.46 1.125 .843 1.58

PHONE: 734-591-0134 • FAX: 734-591-7866

14

FL-Tool Holders

Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders ORDERING INFORMATION 1. Locate desired Tap, Shank

and Holder Series in table.


""""'""~ KEY

OPTIONAL COOLANT SEA~ I' "

-A

t \ ----- ----------------- --- -

B rn - -ACME THREAD lli t -- ----- ----- --- -

I : 0250~ E~

D .. C

E

TAP PART NUMBER B A

C SIZE SHANK SERIES

DSA-0-8000 1/2-16 #6 DSA-0-8001 5/8-1 6

DSA-0-8002 3/4-12 .141 DSA-0-8003 7/8-12

SHANK DSA-0-8004 1-12 DSA-0-8005 1 1/16-12

DSA-0-8008 1/2-16 #8 DSA-0-8009 5/8-16

DSA-0-8010 3/4-12 .168 DSA-0-8011 7/8-12

SHANK DSA-0-8012 1-12 DSA-0-8013 1 1/16-12 #0

SERIES 1.187 DSA-0-8016 1/2-16 1.500

#10 DSA-0-8017 5/8-16 DSA-0-8018 3/4-12

.195 DSA-0-8019 7/8-12 SHANK DSA-0-8020 1-12

DSA-0-8021 1 1/16-12

DSA-0-8024 1/2-16 #12 DSA-0-8025 5/8-16

DSA-0-8026 3/4-12 .220 DSA-0-8027 7/8-12

SHANK DSA-0-8028 1-12 DSA-0-8029 1 1/16-12

N • -r-

'-

~I. F-

0 E

3.000 5_562 3.000 5.562 3.000 5.562 3_625 6_187 3.625 6.187 3_625 6_187

3.000 5.562 3_000 5.562 3_000 5.562 3.625 6.187 3.625 6.187 3.625 6.187

3.000 5.562 3.000 5.562 3.000 5.562 3.625 6.187 3.625 6.187 3.625 6.187

3.000 5.562 3.000 5_562 3_000 5.562 3.625 6.187 3.625 6.187 3.625 6.187

TAP DEPTH TAP SIZE ENTERS

#10 1.125 #12 1.125

I T ~ L 1 :v

~ G

M

F G

1.375 1.00

Radial Float .032 Per Side

N M

4.187 1

4.250 11/16

4.437 11/4

4.437 1 1/4

15--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150





V""~""~ KEY

OP TIONAL COOLANT SEAL\

I~

t ~ ---------------- ---------

B ACME THREAD lli--1

! ----- -------- --------

t== 0.250 ~

D

TAP PART NUMBER

B A SIZE SHANK SERIES

DSA-D-8D32 1/2-16 1/4 DSA-0-8033 5/8-16

DSA-0-8034 3/4-12 _255 DSA-0-8035 7/8-2

SHANK DSA-0-8036 1-12 DSA-0-8037 1 1/16-12

DSA-0-8040 1/2-16 5/16 DSA-0-8041 5/8-16

DSA-0-8042 3/4-12 .318 DSA-0-8043 7/8-12

SHANK DSA-0-8044 1-12 #0 DSA-0-8045 1 1/16-12 SERIES

1.500 DSA-0-8048 1/2-16

3/8 DSA-0-8049 5/8-16 DSA-0-8050 3/4-12

.381 DSA-0-8051 7/8-12 SHANK DSA-0-8052 1-12

DSA-0-8053 1 1/16-12

1/8 LSP DSA-0-8500 1/2-16 DSA-0-8501 5/8-16

.437 DSA-0-8502 3/4-12 SHANK DSA-0-8503 7/8-12


y.. 1.250

5/16 1250

3/8 1.375

1/8 LSP 1.187

N

-A

r-

- ,

l- i J: j) Radial Float -.l J, .032 Per Side

- I-

.F- .1* ~ G

C F-

E . M

C D E F G N M

3.000 5.562 3.000 5_562 3_DOO 5_562

4.437 1 1/4 3.625 6.187 3.625 6.187 3.625 6.187

1_00 3.000 5.562 3_000 5_562 3.000 5.562

4.710 115/32 3.625 6.187 3.625 6_187

1.187 3.625 6.187 1.375

3.000 5.562 3.000 5.562 3.000 5.562

4_750 19/16 3.625 6_187 3.625 6.187 3.625 6.187 1.125

3_000 5.562 3_000 5_562

4.125 15/16 3.000 5.562 3.625 6_187

-----------------------------------------------------------------------------16 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders




w""'cc,~ KE Y

OPTIONAL COOLAN T SE AL\

t ~ -- -------- ----------- ----

B ACME THREAD U1L-J

! ------- - ----~---- -- --

I'

I: 0.250 ~

D

TAP PART NUMBER

B A SIZE SHANK SERIES

1/4 DSA·l ·8134 3/4·12 DSA·l ·8135 7/8·12

.255 DSA·l ·8136 1·12

SHANK DSA·l ·8137 1 1/16·12 DSA·l ·8138 1 3/8·12

5/16 DSA·l·8142 3/4·12 DSA·l ·8143 7/8·12

.318 DSA·l ·8144 1·12

SHANK DSA·l ·8145 1 1/16·12 DSA·l ·8146 13/8·12

3/8 DSA·l ·8150 3/4·12 DSA·l ·8151 7/8·12 #1

DSA·l ·8152 1·12 SERIES .381

DSA·l ·8153 1 1/16·12 1.812 SHANK

DSA·l·8154 13/8·12

7/16 DSA·l·8157 3/4·12 DSA·l ·8158 7/8·12

.323 DSA·l·8159 1·12

SHANK DSA·l·8160 1 1/16·12 DSA·l·8161 13/8·12

1/2 DSA·l·8164 3/4·12 DSA·l ·8165 7/8·12

.367 DSA·l·8166 1·12

SHANK DSA·l ·8167 1 1/16·12 DSA·l ·8168 13/8·12

N

- A

~ ~ ~

- r-

I - L

-'--

.E C .\. 'F-

E

C 0 E

3.000 5.562 3.625 6.187 3.625 6.187 3.625 6.187 4.625 7.187

3.000 5.562 3.625 6.187 3.625 6.187 3.625 6.187 4.625 7.187

3.000 5.562 3.625 6.187

1.187 3.625 6.187 3.625 6.187 4.625 7.187

3.000 5.562 3.625 6.187 3.625 6.187 3.625 6.187

, 4.625 7.187

3.000 5.562 3.625 6.187 3.625 6.187 3.625 6.187 4.625 7.187

iAP SIZE

y.. 5/16

3/8

7/16

~

- G

M

F

1.375

DEPTH TAP ENTERS

1.250

1.250

1.375

1.375

1.375

...

T l" -L ..1/

G

1.00

1.1 25


N M

4.437 11/4

4.710 1 15/32

4.750 19/16

4.968 125/32

5.187 2

17 -----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150




2. Order by Part N umber '" DODR FF "'i KEY

OPT IDNAL IL\ COOLANT SEAL

shown.

t \ -------------------------

rn B -ACME THREAD lli t ----- ------- --------

I' -

-

TAP SIZE

9/16

1/8 LSP

N

r- A

r-

f- r L

~

T ~

DEPTH TAP ENTERS

1.500

1.187

~

R adial Float 32 Per Side .0

1"1 Y

I: 0250 ~ .E .1. - G

D

TAP B A SIZE

PART NUMBER SHANK SERIES

9/16 DSA·l·8172 3/4·12 DSA·l·8173 7/8·12

.429 DSA·l·8174 1·12 DSA·l·8175 11/16·12

SHANK DSA·l ·8176 1 3/8·12 #1

SERIES

1/8lSP DSA·l ·8510 3/4·12 1.812 DSA·l ·8511 7/8·12

.437 DSA·l·8512 1·12 DSA·l·8513 1 1/16·12

SHANK DSA·l·8514 13/8·12

I FEATURES AND BENEFITS I • ALLOWS FOR 1/32 RADIAL FLOAT

• ADJUSTABLE FOR VERTICAL OR

HORIZONTAL MACHINING

• DURABLE THREE PIECE DESIGN

• ARMORCLAD®SURFACE COATING FOR

CORROSION RESISTANCE

• AUTOMATICALLY COMPENSATES

FOR MISALIGNMENT

• POSITIVE DRIVE

E

C

1.187

C F -

M

D E F G N

3.000 5.562 3.625 6.187 3.625 6.187 1.125 5.281 3.625 6.187 4.625 7.187

1.375 3.000 5.562 3.625 6.187 3.625 6.187 1.250 4.125 3.625 6.187 4.625 7.187

OPERATING PROCEDURE

(2) Pull the operating sleeve down.

M

23/32

15/16

o Push Tap into the Holder.

CD Release the Operating Sleeve

PHONE: 734-591-0134 • FAX: 734-591 -7866

18

FL-Tool Holders



2. Order by Part Number shown. VO""'~c~ I~ KE Y

OPTIONAL COOLANT SEAL\

~

t m\ ------ ------------------- -

B -ACME THREAD W---1

i --- ---- ------ -------- -

I :

0.250 ~ .E D

E

TAP PART NUMBER

B A C

SIZE SHANK SERIES

7/16 DSA·2·8259 1·12 .323 DSA·2·8260 11/16·12

SHANK DSA·2·8261 13/8·12

1/2 DSA·2·8266 1·12 .367 DSA·2·8267 11/16·12

SHANK DSA·2·8268 13/8·12

9/1 6 DSA·2·8274 1·12 .429 DSA·2·8275 11/16·12

SHANK DSA·2·8276 13/8·12

5/8 DSA·2·8278 1·12 .480 DSA·2·8279 11/16·12

SHANK DSA·2·8280 1 3/8·12

3/4 DSA·2·8282 1·12 #2 .590 DSA·2·8283 1 1/16·12 SERIES 1.468

SHANK DSA·2·8284 13/8·12 2.187

7/8 DSA·2·8286 1·12 .697 DSA·2·8287 1 1/16·12

SHANK DSA·2·8288 1 3/8·12

1/8lSP DSA·2·8520 1·12 , .437 DSA·2·8521 11/16·12

SHANK DSA·2·8522 13/8·12

1/4 NPT DSA·2·8528 1·12 .562 DSA·2·8529 1 1/16·12

SHANK DSA·2·8530 13/8·12

3/8 NPT DSA·2·8536 1·12 .700 DSA·2·8537 11/16·12

SHANK DSA·2·8538 13/8·1 2

N

-A

-.. ~

-

l-

cl F-

D E

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3,625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593

3.625 6.593 3.625 6.593 4.625 7.593


7/16 1.375

1.375

9/16 1.500

1/8 PLG 1.187

11, PLG 1.312

r T l 1-

- G

M

F G

1.125

1.250

1.500

1.500

1.125

1.250

1.375

·1 Radial Float 032 Per Side

"'1"-.v

N M

5.125 1 25/32

5.343 2

5.437 23/32

5.656 25/16

5.843 21/2

6.281 215/16

4.28 15/16

4.468 1 1/8

4.53 13/16



Quick Change Dedicated Size Radial Floating Acme Shank Tap Holders

ORDERING INFORMATION 1. Locate desired Tap Shank


2. Order by Part Number WOODRUFF

'~ shown . KEY

1 OPT IONAL 'L\ COOLANT SEAL

~

t m\ ------- -------- -- ---- -

B -ACME THREAD lli i - - - - - - - - -

I :

0.250 ~ .E D

E

TAP PART NUMBER

B A C

SIZE SHANK SERIES

5/8 OSA·3·8379 1 1/16·12 .480 OSA·3·8380 1 3/8·12

SHANK OSA·3·8381 1 7/8·12

3/4 OSA·3·8383 11/16·12 .590 OSA·3·8384 1 3/8·12

SHANK OSA·3·8385 1 7/8 ·12

7/8 OSA·3·8386 1 1/16·12 #3 .697 OSA·3·8387 1 3/8·12 SERIES 1.562

SHANK OSA·3·8388 1 7/8·12 2.750

1" OSA,3·8389 1 1/16·12 .800 OSA·3·8390 1 3/8·12

SHANK OSA·3·8391 1 7/8 ·12

1 1/8 OSA·3·8392 11/16·12 .896 OSA·3·8393 1 3/8·12

SHANK OSA·3 ·8394 1 7/8·12

TAP PART NUMBER

B A C

SIZE SHANK SERIES

3/8 NPT OSA·3·8545 1 1/16·12 .700 OSA·3·8546 1 3/8·12

SHANK OSA·3·8547 1 7/8·12

1/2 NPT OSA·3·8553 11/16·12 #3 .687 OSA·3·8554 1 3/8·12 SERIES 1.562

SHANK OSA·3·8555 1 7/8·12 2.750

3/4 NPT OSA·3·8560 1 1/16·12 .906 OSA·3·8561 1 3/8·12

SHANK OSA·3·8562 1 7/8 ·12

TAP SIZE

SIB

0/. 7/B

3/B PT

N

r-A

h ~

-

f- I L

-'--

.1. '- G

C F-

M

D E F G

3.625 6.687 4.625 7.687 1.250 5.625 8.687

3.625 6.687 4.625 7.687 1.375 5.625 8.687

3.625 6.687 4.625 7.687 1.500 1.500 5.625 8.687

3.625 6.687 4.625 7.687 1.625 5.625 8.687

3.625 6.687 4.625 7.687 1.750 5.625 8.687

D E F G

3.625 6.687 4.625 7.687 5.625 8.687

1.375 3.625 6.687 4.625 7.687 1.500 5.625 8.687

3.625 6.687 4.625 7.687 1.625 5.625 8.687

I 1

OEPTH TAP ENTERS

1.500

1.750

1.750

1.375

1 R adial Float

32 Per Side .0 l ' 1/

N M

6.06 25/16

6.25 21/2

6.68 215/16

7.06 35/16

7.31 39/16

N M

4.93 1 3/16

5.25 11/2

5.50 13/4

---------------------------------------------------------------------------20 PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders

CO'llet Type Radial Floating Acme Shank Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shank



.42 OPTIONAL

POSITIVE DRIVE

1-+ ___ _ REF. ---f--~ N

H ------~+-------~ A

HlEI[It-! -L--- t:t:.=:.=:------=------=----c-===-------~- ~

O.250~ E - I F ~I I. D • c -t--- REF---l

COLLET PART NUMBER

B A C D

REF G

SERIES SHANK SERIES F

SAA·O·9100 1/2·1 2 3.00 SAA·O·9l0l 5/8·12

#0 3.00

16 SAA·0·9102 3/4·12

SERIES 3.00

1.670 1.10 SAA·Q·9104 1 "·12 1.5

3.625 SAA·O·9105 1·1/16· 12 3.625 SAA·0·9106 1·3/8 ·12 1.187 4.625

SAA· 1 ·91 07 5/8·12 3.00 SAA· 1 ·91 08 3/4·12 #1 3.00

20 SAA·l ·9ll0 1"·12 SERIES 3.625 1.430 1.34 SAA· 1 ·91" 1·1/16· 12 1.812 3.625 SAA· 1·91 12 1·3/8·12 4.625

SAA·2·9115 3/4·1 2 #2

3.00

25 SAA·2·9117 1"·12

SERIES 1.468 3.625

2.060 1.65 SAA·2·9118 1 ·1/16· 12 2.187

3.625 SAA·2·9119 1·3/8·12 4.625

SAA·3·9125 1·1/16 #3 3.625 32 SAA·3·91 26 1·3/8 SERIES 1.562 4.625 2.30 2.00

SAA·3·9127 1·7/8 2.750 5.625


REF H

N

3.50 1.800

3.29 1.450

4.20 1.812

4.53 2.125

* See pages 23-26 for Collet Information * See page 32 for Positive drive Information

All SA Collet Holders are Available with Positive drive

Call for Detail Information

/.1--------------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150


Collet Type Radial Floating Straight Shank Reamer Holders ORDE~NGINFORMAnON

1. Locate desired Collet, Shank and Holder size in table.


COllET PART NUMBER

SERIES

SAA·0·9201 16 SAA·0·9202

SAA·0·9203

SAA·0·9206 20 SAA·1·9207

SAA·1·9208

SAA·2·9211 25

SAA·2·9212

SAA·3·9216 32

SAA·3·9217

OP TI ONAL COOLANT SEAL

B

i

B SHAN.K

3/4·12 1·12

11 /2·1 2

3/4·12 1·12

1 1/2·12

1·12 1 1/2·12

1 1/2·12 13/4·12

L-n .1. A

C 0 REF

SERIES F

#0 SERIES

1.5 1.187 4.00 1.600

#1 SERIES 1.812

#2 SERIES 1.468 1.375 2. 187

5.00 #3

SERIES 1.562 1.660 2.750

Collet Type Radial Floating Cat V Flange Reamer Holders

ORDERING INFORMATION 1. Locate desired V-Flange,

collet series and Holder size in table.

2. Order by Part Number

COLLET SERIES

16

20

25

32

'B'-V CAT FLANGE

GAGE LINE

RUENTION KNOBS AVAILABLE UPON REQUEST

PART NUMBER B

SHANK SAC·0·40·16 40 SAC·0·50·16 50

SAC·1·40·20 40 SAC·1·50·20 50

SAC·2·40·25 40 SAC·2·50·25 50

SAC·3·40·32 40 SAC·3·50·32 50

,

A

A C F

SERIES

1.500 1.093 1.375

1.812 1.125 1.625

2.187 1.625 1.625

2.750 1.937 1.937

PHONE: 734-591-0134 • FAX: 734-591-7866

G

1.100

1.340

1.650

2.000

G

1.100

1.340

1.650

2.000


REF N

2.812

2.562

2.844

3.219

Radial Float ,032 Per Side

22

FL-Tool Holders

Single Angle Collets (Series 16) ORDERING INFORMATION 1. Locate desired Shank Size

in table.


INCH

PART NUMBER

SA-16-1/16

SA-16-3/32

SA·16·1/8

SA-16-5/32

SA-16·3/16

SA·16·7/32

SA- 16-1/4

SA·16-9/32

SA·16-5/16

SA-16-11 /32

SA·16·3/8

SA- 16·13/32

CLAMPING RANGE PART

NUMBER

.062-_047 SA-16-Ml

.093-078 SA-16-M2

.125·. 110 SA-16-M3

.156·.141 SA·16·M4

187'. 172 SA-16-M5

.218-.203 SA·16·M6

SA-16-M7 250'.235

SA·16·M8 .280-.266

SA-16-M9 .312-.297

SA-16-Ml0 .344-.328

.375·.360

.406-.391


in table.


INCH

PART NUMBER

SA-20·1 /16

SA-20-3/32

SA-20-1/8

SA-20-5/32

SA.·20·3/16

SA-20-7I32

SA·20·1/4

SA-20-9/32

SA·20-5/16

SA-20-11/32

SA-20-3/8

SA-20·13/32

SA-20·7/16

SA-20-15/32

SA-20-1/2

CLAMPING PART RANGE NUMBER

.062·.047 SA·20-M2

.093·.078 SA·20·M3

.125·.110 SA-20·M4

.1 56·. 141 SA·20·M5

.187·.172 SA-20-M6

.218·.203 SA-20-M7

.250·.235 SA·20-M8

.281 ·.203 SA-20·M9

.312-.297 SA·20·Ml0

.343·.328 SA-20·Mll

.375·.360 SA-20-M12

.406-.391 SA·20·M13

.437'.422

.468·.453

500-.485

METRIC

CLAMPING RANGE MM INCH.

1-.05 .039·.019

2·1 .079·.039

3·2 .118-.079

4-3 .157·. 118

5·4 .197·.157

6-5 .236-. 197

7-6 .276-.236

8-7 .315-.276

9·8 .354·.315

10·9 .394-.354

METRIC

CLAMPING RANGE MM INCH

2-1 .079·.039

3·2 .118-.079

4·3 .157·. 118

5-4 .197-.157

6·5 .236-.197

7·6 .276·.236

8·7 .315·.276

9-8 .354-.315

10·9 .394·.354

11 -10 .433,.394

12-11 .472-.433

13·12 .512·472




in table.


INCH

PART NUMBER

SA·251/16

SA·253/32

SA·25 1/8

SA·255/32

SA·253/16

SA·257/32

SA·251 /4

SA·259/32

SA·255/16

SA·2511/32

SA·253/8

SA·2513/32

SA·257/16

SA·2515/32

SA·251/2

SA·25 17/32

SA·259/16

SA·2519/32 SA·255/8


.062·.047 SA·25 M2 :093·.078 SA·25 M3 .125·.110

.156·.141 SA·25 M4

.187·.172 SA·25 M5

.218·.203 SA·25 M6

.250·.235 SA·25 M7

.281·.266

.31 2·.297 SA·25 M8

.343·.328 SA·25 M9

.375·.360 SA·25 Ml0

.406,.391 SA·25 Mll

.437·.422

.468·.453 SA·25 M12

.500·.485 SA·25 M13

.531 ·.516 SA·25 M14

.562·.547 SA·25M15

.593·.578

.625·.610 SA·25 M16


in table.


INCH

PART NUMBER

SA·32·3132

SA·32·1/8

SA·32·5132

SA·32·3/16

SA·32·7132

SA·32·1/4

SA·32·9132

SA·32·5/16

SA·32·11/32

SA·32·3/8

SA·32·13/32

SA·32·7I16

SA·32·15/32

SA·32·1/2

SA·32 ·1 7/32

SA·32·9/16

SA·32·19/32

SA·32·5/8

SA·32·21/32

SA·32·11/16

SA·32·23/32


.093·.078 SA·32·M3

.125·.110 SA·32·M4

.156·.141 SA·32·M5

.187·.172 SA·32·M6

.2 18·.203 SA·32·M7

.250·.235 SA·32·M8

.281 ·.266

.312·.297 SA·32·M9

.343·.328 SA·32·M l0

.375·.360 SA·32·Mll

.406,.391 SA·32·M12

.437·.422 SA·32·M13

.468·.453 SA·32·M14

.500·.485 SA·32·M15

.531 ·.516 SA·32·M16

.562·.547 SA·32·M17

.593·.578 SA·32·M18

.625·.610 SA·32·M19

.656·.641 SA·32·M20

.687·.672

.718·.703

METRIC

CLAMPING MM INCH

2·1 .079·.039

3·2 .118·.079

4·3 .157·. 118

5-4 .197·. 157

6·5 .236·.197

7·6 .276·.236

8·7 .315·.276

9·8 .354·. 315

10·9 .394·.354

11 ·10 .433·.394

12·11 .472-.433

13·12 .512·.472

14·13 .551'.5 12

15·14 .591 ·.551

16·15 .630·.591

METRIC

CLAMPING RANGE MM INCH

3·2 .1 18·.079

4·3 .157·. 118

5-4 .197'. 157

6·5 .236·.197

7·6 .276·.236

8·7 .315·.276

9·8 .354·.315

10·9 .394·.354

11·10 .433· .394

12·11 .472-.433

13 - 12 .512·.472

14·13 .551 ·.512

15·14 .591 ·.551

16·15 .630·. 591

17·16 .669·.630

18·17 .709·.669

19·18 .748·.709

20·19 .787·.748

SA·32·3/4 .750·.735

-------------------=================~~----------------------24 PHONE: 734·591·0134. FAX: 734·591·7866

SAX Tap Collets With Internal Square Drive ORDERING INFORMATION 1. Locate desired Tap Size and

Collet Series in table.


TAP SIZE

#8

#10

#12

1/4

5/16

3/8

7/16

1/2

9/16

5/8

11/16

3/4

13/16

SAX 16 PART #

SAX ·16·168

SAX ·16·194

SAX ·16·220

SAX ·16·255

SAX 20 SAX 25 PART# PART #

SAX· 20-168 SAX· 25·168

SAX ·20·194 SAX ·25·194

SAX ·20·220 SAX ·25·220

SAX ·20·255 SAX ·25·255

SAX ·20·318 SAX ·25·318

SAX ·20·381 SAX ·25·381

SAX ·20·323 SAX ·25·323

SAX ·20·367 SAX ·25·367

SAX ·25-429

SAX ·25·480

FL-Tool Holders

SAX 32 PART #

SAX· 32·168

SAX ·32·194

SAX ·32·220

SAX ·32·255

SAX ·32·318

SAX ·32·381

SAX ·32·323

SAX ·32·367

SAX ·32-429

SAX ·32-480

SAX ·32·542

SAX ·32·590

SAX ·32·652

ALSO AVAILABLE IN METRIC SIZE TAP SHANKS UPON REQUEST

DIMENSIONAL INFORMATION

TAP SIZE B

RANGE A

SA 16 SA 20 SA 25 SA 32

#8 -1/4 0.709 0.374 0.531 0.630 0.866

5/16 - 1/2 0.866 0.374 0.472 0.709

9/16 - 7/8 0.984 0.374 0.591

* THE TAP LOCATES OFF THE ID OF THE COLLET AND DRIVES OFF THE SQUARE OF THE COLLET * POSITIVE DRIVE GIVES ACCURACY AND RIGIDABILITY

25-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150


Single Angle Collet Accuracy

INCH METRIC

CLAMPING RANGE MAXIMUM HR.

D L

PRECISION HIGH PRECISION MIN. MAX.

DIN 6499 · DIN 6499

CLAMPING RANGE MAXIMUM HR.

D L

PRECISION HIGH PRECISION MIN. MAX.

DIN 6499 DIN 6499

0.039 0.063 0.236 1.0 1.6 6

0.063 0.118 0.394 1.6 3.0 10 0.0006 0.0003 0.015 0.008

0.118 0.236 0.630 3.0 6.0 16

0.236 0.394 0.984 6.0 10.0 25

0.394 0.709 1.575 10.0 18.0 40 0.0008 0.0004 0.020 0.010

0.709 1.024 1.969 18.0 26.0 50

1.024 1.339 2.362 0.0010 26.0 34.0 60 0.025

INSERTING AND REMOVING SA COLLETS

INSERTING INSERT COLLET INTO NUT AT AN ANGLE TO ENGAGE CLIP IN NUT TO SEAT INTO THE GROOVE OF THE COLLET

2 SCREW NUT ONTO THE COLLET HOLDER PARTWAY DOWN

3 INSERT THE TOOL AND TIGHTEN DOWN WITH WRENCH

INSTALLATION ANGLE SHOWN

REMOVING 1 LOOSEN THE COLLET NUT ASS'Y WITH WRENCH 2 REMOVE THE TOOL AND UNSCREW THE NUT

FROM HOLDER 3 HOLDING ONTO THE NUT BY PUSH SIDEWARD ON

THE END OF THE COLLET, THUS UNSNAPPING IT OUT OF THE ECCENTRIC RING LOCATED IN THE COLLET NUT

GROOVE IN COLLET

IMPORTANT NOTE: ECCENTRIC RING OF NUT

NEVER SCREW THE NUT DOWN WITH OUT FIRST CHECKING THAT THE COLLET IS PROPERLY INSTALLED.

-----------------------------------------------------------------------------26 PHONE: 734-591-0134. FAX: 734-591-7866

FL-Tool Holders

Collet Type Radial Floating Acme Shank Tap and Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shank

and Holder series size in table .


B

I.tOODRUFF KEY '~

---------- ---- -----------

-3. See Page 29 for Collet

Information. ACME THREAD

L - ------------ --- -- --

I--

-

I: .25 ~.E D

COLLET PART NUMBER SERIES

TCA·0·9501

l ·TCA TCA·0·9502

RANGE TCA·0·9503 TCA·0·9504

0·1/2 TCA·0·9505 TCA·0·9506

l·TCA TCA·l ·9509

RANGE TCA·l ·9510 TCA·l ·9511

0·1/2 TCA·l ·9512

2·TCA TCA·2·9516 RANGE TCA·2·9517

9/16·3/4 TCA·2·9518


7{8·11/4 TCA·3·9526

4·TCA TCA·49528

RANGE TCA·49529 TCA·49530


* HOLDERS SERIES #4TCA AND #5TCA ARE NON STOCKED ITEMS

E

B A C

SHANK SERIES

1/2·16 5/8·16 3/4·12 #0 1·12 1.5

1 1/16·12 13/8·12 1.187

3/4·12 112 #1

11/16·12 1.812 13/8·12

112 #2

1 1/16·12 2.187

1.468 13/8·12

1 1/16·12 #3

13/8·12 2.750

1.562 1 7{8·12

1 1/16·12 13/8·12 #4 1.750 17/812

13/8·12 #5 2.125

1 7/8·12

N

~A

r-

~

~ H1 , I -I-

~ ~

l-

L..-

C lr--

0 F

3.000 3.000 3.000

1.125 3.625 3.625 3.625

3.000 3.625

1.125 3.625 4.625

3.625 3.625 1.156 4.625

3.625 4.625 1.687 5.625

3.625 4.625 2.343 5.625

4.625 3.187

5.625

t G

~ Radial Float .032 Per Side

G N

1.125 213/16

1.125 213/16

1.343 3.125

3.750 2.125 3.750

4.000

4.750 2.750 4.750

4.970

5.970 3.750

6.187

27-----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI48150


Collet Type Radial Floating Straight Shank Tap and Reamer Holders ORDERING INFORMATION 1. Locate desired Collet, Shank

and Holder series in table.


COLLET PART SERIES NUMBER

l ·TC TCA·O·9552 RANGE TCA·0·9553 0·1/2 TCA·0·9554

TCA·l ·9559 l·TC TCA·l ·9560

RANGE TCA·l ·9561 0·1/2 TCA·l ·9562

TCA·l ·9563

2TC TCA·l ·9566

RANGE TCA·l·9567 TCA·2·9568

9/16·3/4 TCA·2·9569

3·TC TCA·3·9571

RANGE TCA·3·9572

7/8·1 1/4 TCA·3·9573 TCA·3·9574

I B

L

I: B

SHANK

3/4 7/8 1

3/4 7/8 1

1 1/4 11/2

1 11/4 1 1/2 13/4

11/4 11/2 13/4

2

* See page 29 for Collet Information

~N r-

-

- Hi - -I-

~ -

-'---'-----.

D .1. elF-E

A C D F

SERIES

#0 1.5

3.00

1.187 1.125

#1 1.812

3.50

#2 1.468 4.00 1.156

2.187

#3 1.562 5.00 1.687

2.75

t G

~

G

1.125

1.687

2.125


N

2.312

2.625

3.25

---------------------------------------------------------------------------- 28 PHONE: 734-591-0134 • FAX: 734-591-7866

Tap Collets ERING INFORMATION ORO

1. Locate desired Tap and 2. Order by Part Number Holder series size in table . Shown.

TAP SHANK FL·TOOL

FORD PART A B

SIZE DIA NUMBER

REF#

0·6 .141 1·TC·141 TA3·141C .1415 .115 8 .168 1·TC·168 TA3·168C .1685 .136 10 .194 1·TC·194 TA3·194C .1945 .157 12 .220 1·TC·220 TA3·220C .2205 .170 1/4 .255 1·TC·255 TA3·255C .2555 .197

5/16 .318 1·TC·318 TA3·318C .3185 .244

3/8 .381 1·TC·381 TA3·381C .3815 .292 7/16 .323 1·TC·323 TA3·323C .3235 .249 1/2 .367 1·TC·367 TA3·367C .3675 .282

9/16 .429 2·TC·429 TA3·429C .4295 .330 5/8 .480 2·TC·480 TAJ.480C .4805 .369 3/4 .590 2·TC·590 TA3·590C .5905 .452

7/8 .697 3·TC·697 TA3·697C .6975 .533 1 .800 3·TC·800 TA3·800C .8005 .611

1·1/8 .896 3·TC·896 TA3·896C .8965 .684 1.1/4 1.021 3·TC·l021 TA3·1021C 1.0215 .781

1/8 SSP .312 1·TC·312 TA3·312C .3125 .240

1/8 LSP .437 2·TC·437 TA3·437C .4375 .335 1/4P .562 2·TC·562 TA3·562C .5625 .430

3/8P .700 3·TC·700 TA3·700C .7005 .541 1/2P .687 3·TC·687 TA3·687C .6875 .525 3/4P .906 3·TC·906 TA3·906C .9065 .691

Reamer Collets ORDERING INFORMATION 1. Locate desired Reamer and

Holder series size in table. 2. Order by Part Number

Shown.

FL·TOOL A B REAM SHANK

PART # ±.002 ± SIZE DIA NUMBER .0005 ·.001

1/8 .1190 1·TC·119R .1 195 -

5/32 .1510 1·TC·151R .1515 .098 3/16 .1805 1·TC·181R .1810 .098 7/32 .2075 1·TC·208R .2080 .126 1/4 .2405 1·TC·241 R .2410 .126

9/32 .2485 1·TC·249R .2490 .126

5/16 - 11/32 .2807 1·TC·281R .2812 .166

3/8 -13/32 .3120 1·TC·312R .3125 .166

7/16-15/32 .3745 HC·375R .3750 .207

1/2 - 19/32 .4370 2·TC·437R .4375 .247

5/8 - 23/32 .5620 3·TC·562R .5625 .307

3/4 - 27/32 .6245 3·TC·625R .6250 .377

7/8 - 31/32 .7495 J.TC·750R .7500 .477

FL-Tool Holders

@ c::-..... r,;;~ --E-D A I-- -+f- I U - __ L

~ 'c f-

~H-

r- E =-1 IT

D DEPTH C HOLDER E F TAP ENTERS

SERIES (HI

.19 .63

.25 .69

.25 .69

.28 .72

.28 #1 1.00 .44 .72

.31 .625 .75

.56 .81

.38 .85

.56 .87

.44 #2

1.00 .44

1.000 1.19 .50 1.06

.69 1.18

.50 1.38

.50 #3 1.44 .62

1.43 .81 1.375 1.50 .81 1.62

.38 #1

1.00 .44 .81

.625 .81

.38 #2 1.19 .50

.88 .69 1.000 .94

.38 #3

1.12 .50 1.44 .62 1.25 .81

1.375 1.31

- L-C F H L M

± HOLDER +.000 +.000 ± .010 SERIES ·.001 ·.002 .010

#1 .69

.625 .499 .396 1.00

.81 #2

.874 .626 1.19 1.000

.94 #3

1.249 .935 1.44 1.375



Morse Taper Radial Floating Acme Shank Tap and Reamer Holders A, B, ORDERING INFORMATION 1. Locate desired Morse Taper


2. Order by Part Number shown. B

IJDDDRUFF KE Y

ACME THREAD

Type A PART A B

NUMBER SIZE SHANK

MTA-1-9830 7/8-12 MTA-1-9831 1.812 1-12 MTA-1-9832 11/16-12

MTA-2-9833 2.187

11/16-12 MTA-2-9834 1 3/8-12

MTA-3-9838 13/8-12

MTA-3-9839 2.750 1 7/8-12

MTA·3-9840

C D

1.187 3_625

1.468 3.625 4.625

1.562 4.625

r:~N A-t---r

F K

MT

lMT .968

2MT .156

3MT .187


N

3.968

4.281

5.281

ORDERING INFORMATION .,.--------~=r------jr=IN~ 1. Locate desired Morse Taper and Holder size in table.

-- -- f Radial Float t-+--ttt-- - G

_ ___ ~ .032 Per Side

2. Order by Part Number shown. B

ACME THREAD

Type B -:5j.E cl,J PART A B

C D F

J K N NUMBER SIZE SHANK MT

MTA·1 -9810 7/8-12 MTA-1-9811 1.81 2 1-12 1.187 3.625 lMT .812 .968 2.625 MTA·l ·9812 11/16-12

MTA-1-9813 2.1 87

1 1/16-12 1.468

3.625 2MT 1.125 1_031 3.00 MTA-2-9814 13/8-12 4.625

MTA-3-9815 2.750 13/8· 12 4.625 3MT 3.625 1.562 1.437 1.562

MTA-3-9816 2.750 1 7/8-12 5.625 3MT 3.875

PHONE: 734-591-0134 • FAX: 734-591-7866

30

FI-Tool Holders

Morse Taper Radial Floating Acme Shank Tap and Reamer Holders C ORDERING INFORMATION

'~ 1. Locate desired Morse Taper I.'OO DR

and Holder size in table. KEY UFF \ I A

- r-

-

-I- 1-1-- - --2. Order by Part Number shown. ! t

AC ME ~HREAD G T ,... ---<-:

- - ..,.,

L ~

1---1. - D - ----.--+--1. c --l-, J .......

-I- 1- 1- - --- -~ -

-

Type C PART A B

C 0 F

J K NUMBER SIZE SHANK MT

MTA·'·9819 7{8·12 MTA·'·9820 1.812 1·12 1.187 3.625 lMT .812 .968 MTA·l ·9821 11{16·12

MTA·'·9823 2.187 1 1/16·12

1.468 3.625

2MT 1.125 1.031 MTA·2·9824 13{8·12 4.625

MTA·3·9826 2.750 13{8·12 4.625 3MT 1.562 1.437 1.562

MTA·3·9828 2.750 1 7{8·12 5.625 3MT


N

2.625

3.00

3.625

3.875

C-NAT'L ACME THREAD

Adjustable Acme Nuts ORDERING INFORMATION 1. Locate desired Morse Taper



PART NUMBER

Fl·622

Fl·623

Fl·624

Fl·625

Fl·626

Fl·627

Fl·628

Fl·629

ACME A HREAO 00 SIZE

1{2·16 .875

5{8·16 1.00

3{4·12 1.250

7{8·12 1.250

1"·12 1.500

1 1{16·12 1.562

13{8·12 1.875

1 7{8·12 2.625

D- SET SCRE'w' SIZE

f--- A -~-l

B 0 WIDTH SET SCREW

.406 1{4·28

.406 1 {4·28

.406 1{4·28

.406 1{4·28

.406 1{4·28

.406 1{4·28

.406 1 {4·28

.625 5/16·24

31----------------------------------------------------------------------------36010 INDUSTRIAL ROAD. LIVONIA, MI 48150

FL-Tool Holders

Tap Shank Information for U.S. Standard Taps

sauAR~I1~---r=-=-: : :~:: : : : : : ::==-::-,..:::::: : SQUARE A/ F SHANK DIAM .

MACHINE SCREW NOM. FRACT. DIAM. INCHES

NOM. METRIC DIAM. SHANK SQUARE SIZE NO. MILLIMETERS DIAMETER A/F

0 1/16 M1.6 .141 .110 1 Ml .8 .141 .110 2 M2. M2.2 .141 .110 3 3/32 M2.5 .141 .110 4 .141 .110 5 1/8 M3. M3.15 .141 .110 6 M3.5 .141 .110 8 5/32 M4 .168 .131 10 3/16 M4.5. M5 .194 .152 12 7/32 .220 .165 14 1/4 M6. M6.3 .255 .191

5/16 M7. M8 .318 .238 3/8 Ml0 .381 .286 7/16 .323 .242 1/2 M12. M12.5 .367 .275

9/16 M14 .429 .322 5/8 M16 .480 .360

11/16 M18 .542 .406 3/4 .590 .442

13/16 M20 .652 .489 7/8 M22 .697 .523

15/16 M24 .760 .570 1 M25 .800 .600

1·1/16 M27 .896 .672 1·1/8 .896 .672 1·3/16 M30 1.021 .766 1·1/4 1.021 .766 1·5/16 M33 1.108 .831 1·3/8 1.108 .831 1·7/16 M36 1.233 .925 1·1/2 1.233 .925 1·5/8 M39 1.305 .979 1·3/4 M42 1.430 1.072 1·7/8 1.519 1.139

2 M48 1.644 1.233 2·1/8 1.769 1.327 2·1/4 M56 1.894 1.420 2·3/8 2.019 1.514 2·1/2 2.100 1.575 2·5/8 M64 2.225 1.669 2·3/4 2.350 1.762 2·7/8 M72 2.475 1.856

3 2.543 1.907 3-1 /8 2.668 2.001 3·1/4 M80 2.793 2.095 3·3/8 2.883 2.162 3·1/2 3.008 2.256 3-5/8 M90 3.133 2.350 3·3/4 3.217 2.413 3·7/8 3.342 2.506

4 Ml00 3.467 2.600

PHONE: 734·591·0134 • FAX.: 734·591·7866

SQUARE LENGTH

.187

.187

.1 87

.187

.187

.187

.187

.250

.250

.281

.312

.375

.437

.406

.437

.500

.562

.625

.687

.687

.750

.750

.81 2

.875

.875 1.000 1.000 1.062 1.062 1.125 1.125 1.1 25 1.250 1.250 1.375 1.375 1.437 1.437 1.500 1.500 1.562 1.562 1.625 1.625 1.750 1.750 2.000 2.000 2.125 2.125 2.250


Phone: 734-591-0134 · Fax: 734-591-7866 VVVI/W, fltoolholders, com

PRECISION TOOLHOLDERS FOR GUN DRILLS AND REAMERS

• Guaranteed Accuracy • Easy Operation

• Compact Size • Pilot Type Flange Mounted

• Patented

FL quick-change gun drill/reamer holders, designed and built by FL-Tool Holders, are available in four different pilot type models.

The pilot model holder is used where radial positioning of the tool is required and provides a guaranteed accuracy of .000050 T.I.R., one inch from the front face of the collet. The basic construction of the gun drill/reamer assembly includes a Jacobs type beveled tooth nosepiece, a tapered collet and nut assembly that securely clamps and unclamps the tool from the holder, and an internal flat that provides positive drive for the tool.

In operation, counterclockwise rotation of a chU9k key wrench causes the beveled tooth nosepiece to rotate in a counterclockwise direction. As the nosepiece turns, the internal collet and nut assembly moves downward into the tapered end of the tool holder causing the collet to constrict and the tool to be tightened along the entire length of the clamping surface. To unlock the chuck and remove the tool , a simple clockwise rotation of the key wrench against the nosepiece is required.



SHRINK FIT STRAIGHT SHANK TOOL HOLDERS



• Patented

Shrink-Fit straight-shank tool holders can be used in existing automotive spindles where rigidity and concentricity are critical. Three separate sizes are available to accommodate tool shank diameters from .2500 (6 .35 mm) to .7500 (19 .05 mm) . All tool shank diameters under .5000 (12 .70 mm) must be solid carbide .

The close fit of the holder 00 to the spindle 10 enables accurate and sec ure positioning of the overthe-spindle adapter collar . Mounted over and existing spindle, the collar is rotated in a clockwise direction to mate with the Acme left-hand thread on the collar, retaining the holder securely against the spindle face . This eliminates the rocking condition seen in all short taper designs. Counterclockwise rotation of the collar forces the tool holder body out of the spindle .

The 10 of the shrink-fit straight-shank holder is slightly smaller than the cutting tool shank diameter. A heat induction unit is used to quickly heat the holder end of the shrinker, expanding the bore's inside diameter. The tool shank then slips easily into the holder and as the holder cools, the resulting thermal contraction exerts tremendous, uniform pressure around the entire surface of the tool shank. No moving parts, no accessories, just total concentric gripping strength .

The average gripping force. imposed on the cutting tool shank is 10,000 pounds, many times greater than that of a collet, milling or hydraulic chuck. Concentricity of the straight-shank shrink-fit holder is .0003 with the cutting tool set in the shrunk condition, extending tool life by up to 1 00% or more.

SHRINK FIT STRAIGHT SHANK TOOL HOLDER SYSTEM

SERIES

10750

11063

11375

(C) MIN. CENTER DISTANCE

+.000 -. 002 (8) DIA. SPINDLE REF.

SPINDLE FACE REF.

LDCKSCR[W ± .OO I 5/'6- 24 UNF - 1.56 R[F. - (0) R[F. --I pr I 1I06J - ( S TANDARD INCLUDED IN ASS'Y 1--_ (G) MIN,/ MAX, TOOL SET RANG[ _

DIA . TOOL SHANK (MA X.) REF.

r .J8 TI1'. REF

(E) DIA. REF.

DESIGN INFORMATION

A·TOOL SIZE A·TOOL SIZE B·MIN. C·MIN. CTR. o REF. E REF. INCHES MILLIMETERS SPDL. DIA. DISTANCE

.2500 - .3750 6.350-9.525 1.315 1750 1.450 1.12

.2500-.5000 6.350- 12.700 1.565 2.000 1.620 1.25

.2500-.7500 6.350-19.050 2.065 2.500 1.750 1.50

F REF. G

MIN. MAX

1.65 1.12 2.90

1.90 1.12 3.50

2.40 1.12 4.10

Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new designs. Cad disk available upon request.

SPIN STRAIGHT SHANK TOOL OLDER

ORDERING INFORMATION

SERIES PART NO.

TOOL HOLDER BODY

10750 10750·SF·E/MXXXX

11063 11063·SF·E/MXXXX

11375 11375·SF·E/MXXXX

Tool Holder Ordering Information: 1) Locate desired tool holder series 2) Specify English (E) or Metric (M) 3) Specify tool shank size (maximum)

Example: 11063-SF-E.5000 11 063-SF-M 1 2.70

OVER THE SPINDLE ADAPTER

10750·A

11063·A

11375·A

Collar and Retaining Ring Ordering Information: 1) Locate desired tool holder series 2) Order by part number

Note: A +.0000 / -. 0002 tolerance is recommended for tool shank dias. Shank taper should not exceed .0001 .

FL-TOOL HOLDERS 36010 Industrial Road • Livonia, Michigan 481 50


SHRINK FIT TAPERED SHANK TOOL HOLDERS

• Increased Machining Efficiency • High Accuracy .Repeatabili1y

• Quick Changeabili1y • Thru Coolant Capabili1y

• Patented

Shrink-Fit tapered tool holders are designed and built to improve product quality and tool life on production and non-production machines. The holders are available in five separate body sizes to accommodate tool shank diameters from .2500 (6 .35 mm) to 1.375 (34.92 mm). All tool shank diameters under .5000 (12.70 mm) must be solid carbide .

Each patented shrink-fit holder features a precision full-length tapered OD shank and a compact design to minimize spindle-to-spindle center distance as well as overhang from the spindle end to the bearing journal diameters. These features make the shrink-fit tapered tool holder ideal for multiple spindle applications where rigidity and concentricity are critical.

The ID of the shrink-fit holder is slightly smaller than the cutting tool shank diameter. A heat induction unit is used to quickly heat the holder end expanding the bore's inside diameter. The tool shank then slips easily into the holder and as the holder cools, the resulting thermal contraction exerts tremendous, uniform pressure around the entire surface of the tool shank. No moving parts, no accesso" ries, just total concentric gripping strength .

The average gripping force imposed on the cutting tool shank is 10,000 pounds, many times

, greater than that of a collet, milling or hydraulic chuck. Concentricity of the shrink-fit tapered holder is .0003 with the cutting tool set in the shrunk condition, extending tool life by up to 100% or more.

SHRINK FIT TAPERED TOOL HOLDER SYSTEM

SERIES

2002

3002

4002

5002

6002

.1'" --4, -

(c) MIN. CENTER DISTANCE

DIA. TOOL SHANK (MAX.) REF.

rJ8 ryP REF

r.---=~~--+---L--.

, ------ --- -+----'----, .;-- - .;

'-<L .. --",,~_ , '--.-

( B) MIN. SPINDLE DIA.

A·TOOL SIZE INCHES

.2500 - .3750

.2500-.5000

.2500-.7500

.2500-1 .0000

.3750-1.3750

± .OO I (D) REF.

( H) MIN./MAX. TOOL SET RANGE

(E) DIA. REF.

DESIGN INFORMATION A·TOOL SIZE B·MIN. C·MIN. CTR. o REF. E REF.

MILLIMETERS SPDL. DIA. DISTANCE

6.350- 9.525 1.315 1750 1.450 1.12

6.350-12.700 1.565 2.000 1.620 1.25

6.350- 19.050 2.065 2.500 1.750 1.50

6.350- 25.400 2.565 3.000 2.100 1.75

9.525- 34.925 3.060 3.500 2.260 2.12

F REF. G REF.

1.65 1.06

1.90 1.06

2.40 1.06

2.88 1.18

3.38 1.18

H MIN. MAX

1.12 2.90

1.12 3.50

1.12 4.10

1.62 5.00

1.62 5.80

Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new designs, Cad disk available upon request.

ORDERING INFORMATION

SERIES PART NO.

TOOL HOLDER BODY

2002 2002 ·SF·E/MXXXX

3002 3002·SF·E/MXXXX



6002 600t-SF·E/MXXXX

Tool Holder Ordering Information: 1) Locate desired tool holder series 2) Specify English (E) or Metric (M) 3) Specify tool shank size (maximum)

Example: 4002-SF-E ,5000 4002-SF-M 12,70

SPINDLE COLLAR SPINDLE COLLAR & RING

RETAIN. RING ASSEMBLY

2002·C 2002·R 2002·CR

3002·C 3002·R 3002·CR

4002·C 4002·R 4002·CR

500z.c 5002·R 5002·CR

600z.c 6002·R 6002·CR

Collar and Retaining Ring Ordering Information: 1) Locate desired too l holder series 2) Order by part number

Note: A + .0000 / -.0002 tolerance is recommended for tool shank dias. Shank taper should not exceed .0001 .

fl tool catalog

Documents